Socay ESD0402LC05N15 Surface mount polymer esd suppressor Datasheet

Surface Mount Polymer ESD Suppressors
ESD0402LC05N15
Description
ESD0402LC05N15 is applied to electrostatic discharge (ESD)
protection. It is designed to protect the high-speed data lines
against ESD transients. It has very low capacitance and fast
turn on times makes it ideal for data and transmission lines
with high data rates. It can apply to HDMI, USB3.0, Display
port, Thunderbolt, etc.
Features
u
Protection
against
ESD
voltages
and
currents
(IEC61000-4-2 Level 4)
u
Equivalent Circuits
Extremely quick response time (<1ns) present ideal ESD
protection
u
Extremely low capacitance (0.05pF typical)
u
Bi-directional device
u
SMD (Surface Mount Device)
u
Zero signal distortion
Electrical Characteristics
Symbol
Unit
Min
Typical
Rated Voltage
VDC
V
Trigger Voltage
VT
V
300
Clamping Voltage
VC
V
20
Capacitance, @1MHz
CP
pF
0.05
15
Response time
ns
ESD Voltage Capability, Contact Discharge Mode
KV
8
ESD Voltage Capability, Air Discharge Mode
KV
15
Pulses
1000
ESD Pulse Withstand
Max.
1
VT - Measurement by using Transmission Line Pulse (TLP)
VC - Measurement by using Transmission Line Pulse (TLP)
CP - Device Capacitance measured with 1Vrms
SOCAY Electronics Co., Ltd.
Revision November 08, 2013
www.socay.com
1/4
@SOCAY Electronics Co., Ltd. 2013
Specifications are subject to change without notice.
Please refer to www.socay.com for current information.
Surface Mount Polymer ESD Suppressors
ESD0402LC05N15
Explanation of Part Number
ESD
0402
LC
05
N
15
(1)
(2)
(3)
(4)
(5)
(6)
(1) Series Type: ESD Guard
TM
Series
(2) Chip Size (EIA): 0402
(3) Series Type: Extremely low capacitance CEMI / ESD Protection
(4) Capacitance: Value - xx, 05=0.05pF
(5) Capacitance Tolerance: N - ±30%, M - ±20%
(6) Rated Voltage, VDC
Construction & Dimensions
Unit: mm
Substrate
Ceramic (Alumina)
Symbol
Spec.
Encapsulate
Polymer
L
1.00±0.1
End termination
Ag / Ni / Sn
W
0.50±0.1
H
0.38±0.1
B
0.25±0.15
A
0.50±0.1
C
0.50±0.1
D
0.50±0.1
Recommended pad outline
SOCAY Electronics Co., Ltd.
Revision November 08, 2013
www.socay.com
2/4
@SOCAY Electronics Co., Ltd. 2013
Specifications are subject to change without notice.
Please refer to www.socay.com for current information.
Surface Mount Polymer ESD Suppressors
ESD0402LC05N15
Temperature Specifications
Environmental Specifications
Item
Thermal
Shock
Specifications
Test Condition
IL≤ 10μA
-40°C to +85°C,30 min.
cycle, 5 cycles
High
Temperature
IL≤ 10μA
Solder leach
Resistance
IL≤ 10μA
Reference
JIS C0025
(1998)Test Na
Rated Voltage, 85°C,
1000hrs
MIL-STD-202G
Method 108
260°C, 10s
MIL-STD-202G
Method 210F
Parameter
Value
Unit
Operating Temperature
-55 to +85
°C
Storage Temperature
--55 to +85
°C
Storage Temperature
5 to 40
°C
Relative Humidity
<65
%RH
Storage Time
12 Max
Month
Taping Package
Storage Condition
IL - Leakage current at rated voltage, the maximum leakage current was
measured after reliability test.
Construction & Dimensions
Unit: mm
Reflow Condition
Pb free assembly
TP
Ramp-up
Critical Zone
TL to TP
-Temperature Min (Ts(min))
+150°C
-Temperature Max (Ts(max))
+200°C
-Time (min to max) (TS)
60 -180 Seconds
TL
Pre Heat
Temperature
TS(max)
Ramp-down
TS(min)
Average ramp up rate ( Liquidus Temp TL)
to peak
3°C/Second Max
TS(max) to TL - Ramp-up Rate
3°C/Second Max
Preheat
25
Time to peak temperature
(t 25℃ to peak)
Time
- Temperature (TL) (Liquidus)
+217°C
- Time (min to max) (TL)
60 -150 Seconds
Reflow
Precaution for soldering
Note that this product will be easily damaged by rapid heating,
rapid cooling or local heating.
Do not give heat shock over 100°C in the process of soldering.
We recommend to take preheating and gradual cooling
Soldering gun procedure
Note the follows, in case of using solder gun for replacement.
1) The tip temperature must be less than 280 for the period
within 3 seconds by using soldering gun under 30W
2) The soldering gun tip shall not touch this product directly.
Peak Temperature (TP)
260 +0/-5°C
Time within 5°C of actual peak
Temperature (TP)
20-40 Seconds
Ramp-down Rate
6°C/Second Max
Time 25°C to peak Temperature (TP)
8 minutes Max
Soldering volume
Note that excess of soldering volume will easily get crack the
body of this product.
SOCAY Electronics Co., Ltd.
Revision November 08, 2013
www.socay.com
3/4
@SOCAY Electronics Co., Ltd. 2013
Specifications are subject to change without notice.
Please refer to www.socay.com for current information.
Surface Mount Polymer ESD Suppressors
ESD0402LC05N15
Packaging Information
Carrier Tape Dimensions
Unit: mm
Packaging method
- Products shall be heat-sealed in the chip pocket, spacing
Symbol
0402
A
8.00±0.30
B
3.50±0.05
C
1.75±0.10
D
2.00±0.05
E
4.00±0.10
F
1.50±0.10
L
1.19±0.05
W
0.69±0.05
T
0.48±0.03
pitch 2-mm of paper carrier tape with cover tape, and carrier
tape shall be reeled to the reel.
- Tape material to be paper.
- Cover Tape adhesion to be 40±15 grams.
Taping Reel Dimensions
Taping Specifications
Unit: mm
There Shall be the portion having no product in
both the head and the end of taping, and there
shall be the cover tape in the heat of taping.
Quantity of products in the taping package
Standard Quantity
0402
10,000PCS / Reel
Shipping quantity is a multiple of standard quantity
SOCAY Electronics Co., Ltd.
Revision November 08, 2013
www.socay.com
4/4
@SOCAY Electronics Co., Ltd. 2013
Specifications are subject to change without notice.
Please refer to www.socay.com for current information.
Similar pages