TT GUS-QS8BLF012001-G Surface mount qsop resistor network Datasheet

Surface Mount QSOP
Resistor Networks
QSOP Series
•
•
•
•
•
Reliable, no internal cavity
High resistor density - .025" lead spacing
Standard JEDEC 16, 20, and 24 pin packages
Ultra-stable TaNSil® resistors on silicon substrate
RoHS compliant and Sn/Pb terminations available
IRC’s TaNSil® QSOP resistor networks are the perfect solution for high volume applications that demand a
small wiring board footprint. The 0.025" lead spacing provides higher lead density, increased component
count, lower resistor cost, and high reliability.
The tantalum nitride film system on silicon provides precision tolerance, exceptional TCR tracking, low cost
and miniature package. Excellent performance in harsh, humid environments is a trademark of IRC’s
self-passivating TaNSil® resistor film.
The QSOP series is ideally suited for the latest surface mount assembly techniques and each lead can be
100% visually inspected. The compliant gull wing leads relieve thermal expansion and contraction stresses
created by soldering and temperature excursions.
For applications requiring high performance resistor networks in a low cost, surface mount package, specify
IRC QSOP resistor networks.
Electrical Data
Environmental Data
Resistance Range
10 to 250KΩ
Absolute Tolerance
To ±0.1%
Ratio Tolerance to R1
To ±0.05%
Absolute TCR
To ±25ppm/°C
Tracking TCR
To ±5ppm/°C
Typical
Delta R
Max Delta
R
Thermal Shock
±0.02%
±0.1%
Power Conditioning
±0.03%
±0.1%
High Temperature Exposure
±0.03%
±0.05%
Short-time Overload
±0.02%
±0.05%
Low Temperature Storage
±0.03%
±0.05%
Life
±0.05%
±2.0%
Test Per
MIL-PRF-83401
Element Power Rating @ 70°C
Isolated Schematic
100mW
Bussed Schematic
50mW
Package Power Rating @ 70°C
16-Pin
20-Pin
24-Pin
Rated Operating______
Voltage
(not to exceed √ P x R)
Operating Temperature
Noise
750mW
1.0W
1.0W
100 Volts
-55°C to +125°C
<-30dB
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
QSOP Series Issue January 2009 Sheet 1 of 4
Surface Mount QSOP
Resistor Networks
Manufacturing Capability Data
ISOLATED SCHEMATIC A
Absolute
TCR
(ppm/°C)
BUSSED SCHEMATIC B
Ohmic
Range
(Ω)
Available
Tolerances
Available
Ratio
Tolerances
Best
Tracking
(±ppm/°C)
Ohmic
Range
(Ω)
Available
Tolerances
Available
Ratio
Tolerances
Best
Tracking
(±ppm/°C)
10-25
FGJ
FG
100
10-25
FGJ
FG
200
26-50
DFGJ
CDFG
50
26-50
FGJ
DFG
100
51-200
CDFGJ
CDFG
10
51-100
DFGJ
CDFG
50
201-250K
BCDFGJ
ABCDFG
5
101-200
DFGJ
BCDFG
25
201-500
BCDFGJ
BCDFG
20
501-100K
BCDFGJ
ABCDFG
5
250
100
50
26-50
DFGJ
CDFG
50
26-50
FGJ
DFG
100
51-200
CDFGJ
CDFG
5
51-100
DFGJ
CDFG
50
201-250K
BCDFGJ
ABFG
5
101-200
DFGJ
BCDFG
25
201-500
BCDFGJ
BCDFG
20
501-100K
BCDFGJ
ABCDFG
5
26-50
DFGJ
CDFG
50
51-100
DFGJ
CDFG
50
51-200
CDFGJ
CDFG
10
101-200
DFGJ
BCDFG
25
201-250K
BCDFGJ
ABFG
5
201-500
BCDFGJ
BCDFG
20
501-100K
BCDFGJ
ABCDFG
5
51-200
CDFGJ
CDFG
10
201-500
BCDFGJ
BCDFG
20
201-250K
BCDFGJ
ABFG
5
501-100K
BCDFGJ
ABCDFG
5
25
© IRC Advanced Film Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
QSOP Series Issue January 2009 Sheet 2 of 4
Surface Mount QSOP
Resistor Networks
Physical Data
# OF PINS
DIMENSION "D"
ZD REF
16
0.193″ ±0.004
0.009″
20
0.341″ ±0.004
0.058″
24
0.341″ ±0.004
0.033″
Note: N = number of pins (16, 20, 24)
Note: Lead Coplanarity 0.004" Max.
Note: All dimesions exclude mold flash and
end flash which shall not exceed 0.006" per side.
Drawing proportions not to scale.
Schematic Data
Power Derating Curve
N
R1
1
2
3
Schematic A
Isolated
N
R1
% Of Rated Power
100
50
10
1
2
3
Schematic B
Bussed
25°
70°
125°
Temperature in °C
Note: N = number of pins (16, 20, 24)
© IRC Advanced Film Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
QSOP Series Issue January 2009 Sheet 3 of 4
Surface Mount QSOP
Resistor Networks
Ordering Data
Prefix
GUS - QS8A - 01 - 1002 - F
B
Style, Schematic and Termination
QS8A = 16-pin, 8 Isolated Resistors, with standard Sn/Pb terminations
QS8ALF = 16-pin, 8 Isolated Resistors, with 100% matte tin, Pb-free terminations
QS8B = 16-pin, 15 Bussed Resistors, with standard Sn/Pb terminations
QS8BLF = 16-pin, 15 Bussed Resistors, with 100% matte tin, Pb-free terminations
QS0A = 20-pin, 10 Isolated Resistors, with standard Sn/Pb terminations
QS0ALF = 20-pin, 10 Isolated Resistors, with 100% matte tin, Pb-free terminations
QS0B = 20-pin, 19 Bussed Resistors, with standard Sn/Pb terminations
QS0BLF = 20-pin, 19 Bussed Resistors, with 100% matte tin, Pb-free terminations
QSCA = 24-pin, 12 Isolated Resistors, with standard Sn/Pb terminations
QSCALF = 24-pin, 12 Isolated Resistors, with 100% matte tin, Pb-free terminations
QSCB = 24-pin, 23 Bussed Resistors, with standard Sn/Pb terminations
QSCBLF = 24-pin, 23 Bussed Resistors, with 100% matte tin, Pb-free terminations
Absolute TCR Code
00 = ±250 ppm/°C; 01 = ±100 ppm/°C; 02 = ±50 ppm/°C; 03 = ±25 ppm/°C
Resistance Code
4-Digit Resistance Code
Ex: 1002 = 10KΩ, 50R1 = 50.1Ω
Absolute Tolerance Code
J = ±5%; G = ±2%; F = ±1%; D = ±0.5%; C = ±0.25%; B = ±0.1%
Ratio Tolerance Code (optional)
G = ±2%; F = ±1%; D = ±0.5%; C = ±0.25%; B = ±0.1%; A = ±0.05%
Packaging
Specify tubes or tape & reel.
For additional information or to discuss your specific requirements,
please contact our Applications Team using the contact details below.
© IRC Advanced Film Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
QSOP Series Issue January 2009 Sheet 4 of 4
Similar pages