TI1 ISO1540-Q1 Iso154x-q1 low-power bidirectional i2c isolator Datasheet

Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
ISO1540-Q1, ISO1541-Q1
SLLSEX0 – NOVEMBER 2016
2
ISO154x-Q1 Low-Power Bidirectional I C Isolators
1 Features
3 Description
•
•
The ISO1540-Q1 and ISO1541-Q1 devices are lowpower, bidirectional isolators that are compatible with
I2C interfaces. These devices have logic input and
output buffers that are separated by Texas
Instruments Capacitive Isolation technology using a
silicon dioxide (SiO2) barrier. When used with isolated
power supplies, these devices block high voltages,
isolate grounds, and prevent noise currents from
entering the local ground and interfering with or
damaging sensitive circuitry.
1
•
•
•
•
•
•
Qualified for Automotive Applications
AEC-Q100 Qualified With the Following Results:
– Device Temperature Grade 1: –40°C to
+125°C Ambient Operating Temperature
– Device HBM ESD Classification Level 3A
– Device CDM ESD Classification Level C6
Isolated Bidirectional, I2C Compatible,
Communication
Supports up to 1-MHz Operation
3-V to 5.5-V Supply Range
Open-Drain Outputs With 3.5-mA Side 1 and 35mA Side 2 Sink Current Capability
±50-kV/µs Transient Immunity (Typical)
Safety-Related Certifications:
– 4242-VPK Isolation per DIN V VDE V 0884-10
(VDE V 0884-10): 2006-12
– 2500-VRMS Isolation for 1 Minute per UL 1577
– CSA Component Acceptance Notice 5A, IEC
60950-1 and IEC 61010-1 End Equipment
Standards
– CQC Basic Insulation per GB4943.1-2011
– UL 1577 Certification Complete; All Other
Certifications Planned
2 Applications
•
•
•
•
•
•
•
Electric and Hybrid-Electric Vehicles
Isolated I2C Buses
SMBus and PMBus Interfaces
Open-Drain Networks
Motor Control Systems
Battery Management
I2C Level Shifting
This isolation technology provides for function,
performance, size, and power consumption
advantages when compared to optocouplers. The
ISO1540-Q1 and ISO1541-Q1 devices enable a
complete isolated I2C interface to be implemented
within a small form factor.
The ISO1540-Q1 has two isolated bidirectional
channels for clock and data lines while the ISO1541Q1 has a bidirectional data and a unidirectional clock
channel. The ISO1541-Q1 is useful in applications
that have a single master while the ISO1540-Q1 is
suitable for multi-master applications. For applications
where clock stretching by the slave is possible, the
ISO1540-Q1 device should be used.
Isolated bidirectional communication is accomplished
within these devices by offsetting the low-level output
voltage on side 1 to a value greater than the highlevel input voltage on side 1, thus preventing an
internal logic latch that otherwise would occur with
standard digital isolators.
Device Information(1)
PART NUMBER
ISO1540-Q1
ISO1541-Q1
PACKAGE
SOIC (8)
BODY SIZE (NOM)
4.90 mm × 3.91 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Simplified Schematic
VCC2
Isolation Capacitor
VCC1
SDA1
or SCL1
GND1
SDA2
or SCL2
GND2
VREF
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
ISO1540-Q1, ISO1541-Q1
SLLSEX0 – NOVEMBER 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
6.11
6.12
6.13
6.14
7
8
8.1
8.2
8.3
8.4
8.5
1
1
1
2
3
4
9
Overview .................................................................
Functional Block Diagrams .....................................
Feature Description.................................................
Isolator Functional Principle....................................
Device Functional Modes........................................
17
17
18
18
19
Application and Implementation ........................ 20
9.1 Application Information............................................ 20
9.2 Typical Application .................................................. 22
Absolute Maximum Ratings ...................................... 4
ESD Ratings.............................................................. 4
Recommended Operating Conditions....................... 5
Thermal Information .................................................. 5
Power Ratings........................................................... 5
Insulation Specifications............................................ 6
Safety-Related Certifications..................................... 7
Safety Limiting Values .............................................. 7
Electrical Characteristics........................................... 8
Supply Current Characteristics ............................... 9
Timing Requirements .............................................. 9
Switching Characteristics ...................................... 10
Insulation Characteristics Curves ......................... 11
Typical Characteristics .......................................... 12
10 Power Supply Recommendations ..................... 24
11 Layout................................................................... 24
11.1 Layout Guidelines ................................................. 24
11.2 Layout Example .................................................... 24
12 Device and Documentation Support ................. 25
12.1
12.2
12.3
12.4
12.5
12.6
12.7
Documentation Support ........................................
Related Links ........................................................
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
25
25
25
25
25
25
25
13 Mechanical, Packaging, and Orderable
Information ........................................................... 26
Parameter Measurement Information ................ 15
Detailed Description ............................................ 17
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
2
DATE
REVISION
NOTES
November 2016
*
Initial release.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
ISO1540-Q1, ISO1541-Q1
www.ti.com
SLLSEX0 – NOVEMBER 2016
5 Pin Configuration and Functions
ISO1540-Q1 D Package
8-Pin SOIC
Top View
1
8
VCC2
SDA1
2
7
SDA2
SCL1
3
6
SCL2
GND1
4
5
GND2
Isolation
VCC1
Side 1
Side 2
Not to scale
Pin Functions—ISO1540-Q1
PIN
NAME
NO.
GND1
4
GND2
SCL1
I/O
DESCRIPTION
—
Ground, side 1
5
—
Ground, side 2
3
I/O
Serial clock input / output, side 1
SCL2
6
I/O
Serial clock input / output, side 2
SDA1
2
I/O
Serial data input / output, side 1
SDA2
7
I/O
Serial data input / output, side 2
VCC1
1
—
Supply voltage, side 1
VCC2
8
—
Supply voltage, side 2
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
3
ISO1540-Q1, ISO1541-Q1
SLLSEX0 – NOVEMBER 2016
www.ti.com
ISO1541-Q1 D Package
8-Pin SOIC
Top View
1
8
VCC2
SDA1
2
7
SDA2
SCL1
3
6
SCL2
GND1
4
5
GND2
Isolation
VCC1
Side 1
Side 2
Not to scale
Pin Functions—ISO1541-Q1
PIN
I/O
DESCRIPTION
NAME
NO.
GND1
4
—
Ground, side 1
GND2
5
—
Ground, side 2
SCL1
3
I
Serial clock input, side 1
SCL2
6
O
Serial clock output, side 2
SDA1
2
I/O
Serial data input / output, side 1
SDA2
7
I/O
Serial data input / output, side 2
VCC1
1
—
Supply voltage, side 1
VCC2
8
—
Supply voltage, side 2
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1) (2)
Voltage
MIN
MAX
VCC1, VCC2
–0.5
6
SDA1, SCL1
–0.5
VCC1 + 0.5 (3)
SDA2, SCL2
–0.5
VCC2 + 0.5 (3)
SDA1, SCL1
–20
20
SDA2, SCL2
–100
100
IO
Output current
TJ(MAX)
Maximum junction temperature
Tstg
Storage temperature
(1)
(2)
(3)
–65
UNIT
V
mA
150
°C
150
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values here within are with respect to the local ground pin (GND1 or GND2) and are peak voltage values.
Maximum voltage must not exceed 6 V.
6.2 ESD Ratings
VALUE
V(ESD)
Electrostatic discharge
Human-body model (HBM), per AEC
Q100-002 (1)
All pins except bus pins
±4000
Bus pins
±8000
Charged-device model (CDM), per AEC Q100-011
(1)
4
UNIT
V
±1500
AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
ISO1540-Q1, ISO1541-Q1
www.ti.com
SLLSEX0 – NOVEMBER 2016
6.3 Recommended Operating Conditions
MIN
MAX
VCC1, VCC2
Supply voltage
3
5.5
V
VSDA1, VSCL1
Input and output signal voltages, side 1
0
VCC1
V
VSDA2, VSCL2
Input and output signal voltages, side 2
0
VCC2
V
VIL1
Low-level input voltage, side 1
0
0.5
V
VIH1
High-level input voltage, side 1
0.7 × VCC1
VCC1
V
VIL2
Low-level input voltage, side 2
0
0.3 × VCC2
V
VIH2
High-level input voltage, side 2
0.7 × VCC2
VCC2
V
IOL1
Output current, side 1
0.5
3.5
mA
IOL2
Output current, side 2
0.5
35
mA
C1
Capacitive load, side 1
40
pF
C2
Capacitive load, side 2
400
pF
(1)
UNIT
fMAX
Operating frequency
TA
Ambient temperature
–40
125
°C
TJ
Junction temperature
–40
136
°C
TSD
Thermal shutdown
139
171
°C
(1)
1
MHz
This represents the maximum frequency with the maximum bus load (C) and the maximum current sink (IO). If the system has less bus
capacitance, then higher frequencies can be achieved.
6.4 Thermal Information
ISO154x-Q1
THERMAL METRIC (1)
D (SOIC)
UNIT
8 PINS
RθJA
Junction-to-ambient thermal resistance
114.6
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
69.6
°C/W
RθJB
Junction-to-board thermal resistance
55.3
°C/W
ψJT
Junction-to-top characterization parameter
27.2
°C/W
ψJB
Junction-to-board characterization parameter
54.7
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report (SPRA953).
6.5 Power Ratings
PARAMETER
TEST CONDITIONS
PD
Maximum power dissipation (both sides)
PD1
Maximum power dissipation (side-1)
PD2
Maximum power dissipation (side-2)
VCC1 = VCC2 = 5.5 V, TJ = 150 °C, C1 =
40 pF, C2 = 400 pF;
Input a 1-MHz 50% duty cycle clock signal
MIN
TYP
MAX
UNIT
85
mW
34
mW
51
mW
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
5
ISO1540-Q1, ISO1541-Q1
SLLSEX0 – NOVEMBER 2016
www.ti.com
6.6 Insulation Specifications
PARAMETER
TEST CONDITIONS
VALUE
UNIT
GENERAL
External clearance (1)
Shortest terminal-to-terminal distance through air
>4
mm
CPG
External creepage (1)
Shortest terminal-to-terminal distance across the
package surface
>4
mm
DTI
Distance through the insulation
Minimum internal gap (internal clearance)
0.014
mm
CTI
Comparative tracking index
DIN EN 60112 (VDE 0303-11); IEC 60112
>400
V
Rated mains voltage ≤ 150 VRMS
I–IV
Rated mains voltage ≤ 300 VRMS
I–III
CLR
Material group
II
Overvoltage category
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12
VIORM
(2)
Maximum repetitive peak isolation voltage AC voltage (bipolar)
VIOTM
Maximum transient isolation voltage
Apparent charge (3)
qpd
Barrier capacitance, input to output (4)
CIO
Isolation resistance, input to output (4)
RIO
VTEST = VIOTM
t = 60 s (qualification)
t = 1 s (100% production)
566
VPK
4242
VPK
Method a: After I/O safety test subgroup 2/3, Vini =
VIOTM, tini = 60 s; Vpd(m) = 1.2 × VIORM = 680 VPK, tm
= 10 s
<5
Method a: After environmental tests subgroup 1,
Vini = VIOTM, tini = 60 s; Vpd(m) = 1.6 × VIORM = 906
VPK, tm = 10 s
<5
Method b1: At routine test (100% production) and
preconditioning (type test) Vini = VIOTM, tini = 1 s;
Vpd(m) = 1.875 × VIORM = 1062 VPK, tm = 1 s
<5
VIO = 0.4 sin (2πft), f = 1 MHz
~1
pC
pF
12
VIO = 500 V, TA = 25°C
>10
VIO = 500 V, 100°C ≤ TA ≤ 125°C
>1011
VIO = 500 V at TS = 150°C
>109
Pollution degree
2
Climatic category
40/125/21
Ω
UL 1577
VISO
(1)
(2)
(3)
(4)
6
Withstand isolation voltage
VTEST = VISO = 2500 VRMS, t = 60 s (qualification);
VTEST = 1.2 × VISO = 3000 VRMS, t = 1 s (100%
production)
2500
VRMS
Creepage and clearance requirements should be applied according to the specific equipment isolation standards of an application. Care
should be taken to maintain the creepage and clearance distance of a board design to ensure that the mounting pads of the isolator on
the printed-circuit board do not reduce this distance. Creepage and clearance on a printed-circuit board become equal in certain cases.
Techniques such as inserting grooves and/or ribs on a printed circuit board are used to help increase these specifications.
This coupler is suitable for basic electrical insulation only within the maximum operating ratings. Compliance with the safety ratings shall
be ensured by means of suitable protective circuits.
Apparent charge is electrical discharge caused by a partial discharge (pd).
All pins on each side of the barrier tied together creating a two-terminal device
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
ISO1540-Q1, ISO1541-Q1
www.ti.com
SLLSEX0 – NOVEMBER 2016
6.7 Safety-Related Certifications
VDE
CSA
UL
CQC
Plan to certify according to DIN V
VDE V 0884-10 (VDE V 088410):2006-12 and DIN EN 61010-1
(VDE 0411-1):2011-07
Plan to certify under CSA
Component Acceptance Notice
5A, CSA/IEC 60950-1, and
CSA/IEC 61010-1
Basic Insulation
Maximum Transient Overvoltage,
4242 VPK;
Maximum Repetitive Peak Voltage,
566 VPK
2.8-kVRMS Insulation Rating; 400
VRMS Basic Insulation working
voltage per CSA 60950-107+A1+A2 and IEC 60950-1 2nd
Ed.+A1+A2;
Single protection, 2500 VRMS
300 VRMS Basic, 150 VRMS
Reinforced Insulation working
voltage per CSA 61010-1-12 and
IEC 61010-1 3rd Ed.,
Basic Insulation, Altitude ≤ 5000
m, Tropical Climate, 250 VRMS
maximum working voltage
Certification planned
Certification planned
Certification planned
Recognized under UL 1577
Component Recognition
Program
File number: E181974
Plan to certify according to
GB4943.1-2011
6.8 Safety Limiting Values
Safety limiting intends to minimize potential damage to the isolation barrier upon failure of input or output circuitry. A failure of
the I/O can allow low resistance to ground or the supply and, without current limiting, dissipate sufficient power to overheat
the die and damage the isolation barrier, potentially leading to secondary system failures.
PARAMETER
IS
TS
Safety input, output, or supply
current
TEST CONDITIONS
MIN
TYP
MAX
RθJA = 114.6°C/W, VI = 5.5 V, TJ = 150°C, TA = 25°C,
see Figure 1
198
RθJA = 114.6°C/W, VI = 3.6 V, TJ = 150°C, TA = 25°C,
see Figure 1
303
Safety temperature
UNIT
mA
150
°C
The safety-limiting constraint is the maximum junction temperature specified in the data sheet. The power
dissipation and junction-to-air thermal impedance of the device installed in the application hardware determines
the junction temperature. The assumed junction-to-air thermal resistance in the Thermal Information table is that
of a device installed on a high-K test board for leaded surface-mount packages. The power is the recommended
maximum input voltage times the current. The junction temperature is then the ambient temperature plus the
power times the junction-to-air thermal resistance.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
7
ISO1540-Q1, ISO1541-Q1
SLLSEX0 – NOVEMBER 2016
www.ti.com
6.9 Electrical Characteristics
over recommended operating conditions, unless otherwise noted
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SIDE 1 (ONLY)
VILT1
Voltage input threshold low, SDA1
and SCL1
500
550
660
mV
VIHT1
Voltage input threshold high, SDA1
and SCL1
540
610
700
mV
VHYST1
Voltage input hysteresis
VIHT1 –VILT1
40
60
VOL1
Low-level output voltage, SDA1
and SCL1 (1)
0.5 mA ≤ (ISDA1 and ISCL1) ≤ 3.5 mA
650
ΔVOIT1
Low-level output voltage to highlevel input voltage threshold
difference, SDA1 and SCL1 (1) (2)
0.5 mA ≤ (ISDA1 and ISCL1) ≤ 3.5 mA
50
mV
800
mV
mV
SIDE 2 (ONLY)
VILT2
Voltage input threshold low, SDA2
and SCL2
0.3 × VCC2
0.4 × VCC2
V
VIHT2
Voltage input threshold high, SDA2
and SCL2
0.4 × VCC2
0.5 × VCC2
V
VHYST2
Voltage input hysteresis
VIHT2 – VILT2
VOL2
Low-level output voltage, SDA2
and SCL2
0.5 mA ≤ (ISDA2 and ISCL2) ≤ 35 mA
0.05 × VCC2
V
0.4
V
10
µA
BOTH SIDES
|II|
Input leakage currents, SDA1,
SCL1, SDA2, and SCL2
VSDA1, VSCL1 = VCC1;
VSDA2, VSCL2 = VCC2
CI
Input capacitance to local ground,
SDA1, SCL1, SDA2, and SCL2
VI = 0.4 × sin(2E6πt) + 2.5 V
CMTI
Common-mode transient immunity
See Figure 21
VCCUV
VCC undervoltage lockout
threshold (3)
(1)
(2)
(3)
8
0.01
7
pF
25
50
kV/µs
2.1
2.5
2.8
V
This parameter does not apply to the ISO1541-Q1 SCL1 line as it is unidirectional.
∆VOIT1 = VOL1 – VIHT1. This represents the minimum difference between a Low-Level Output Voltage and a High-Level Input Voltage
Threshold to prevent a permanent latch condition that would otherwise exist with bidirectional communication.
Any VCC voltages, on either side, less than the minimum will ensure device lockout. Both VCC voltages greater than the maximum will
prevent device lockout.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
ISO1540-Q1, ISO1541-Q1
www.ti.com
SLLSEX0 – NOVEMBER 2016
6.10 Supply Current Characteristics
over recommended operating conditions, unless otherwise noted. For more information, see Figure 19.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
VSDA1, VSCL1 = GND1; VSDA2, VSCL2 = GND2;
R1, R2 = Open; C1, C2 = Open
2.4
3.6
VSDA1, VSCL1 = VCC1; VSDA2, VSCL2 = VCC2;
R1, R2 = Open; C1, C2 = Open
2.5
3.8
VSDA1, VSCL1 = GND1; VSDA2, VSCL2 = GND2;
R1, R2 = Open; C1, C2 = Open
2.1
3.3
VSDA1, VSCL1 = VCC1; VSDA2, VSCL2 = VCC2;
R1, R2 = Open; C1, C2 = Open
2.3
3.6
VSDA1, VSCL1 = GND1; VSDA2, VSCL2 = GND2;
R1, R2 = Open; C1, C2 = Open
1.7
2.7
VSDA1, VSCL1 = VCC1; VSDA2, VSCL2 = VCC2;
R1, R2 = Open; C1, C2 = Open
1.9
3.1
VSDA1, VSCL1 = GND1; VSDA2, VSCL2 = GND2;
R1,R2 = Open; C1,C2 = Open
3.1
4.7
VSDA1, VSCL1 = VCC1; VSDA2, VSCL2 = VCC2;
R1, R2 = Open; C1, C2 = Open
3.1
4.7
VSDA1, VSCL1 = GND1; VSDA2, VSCL2 = GND2;
R1, R2 = Open; C1, C2 = Open
2.8
4.4
VSDA1, VSCL1 = VCC1; VSDA2, VSCL2 = VCC2;
R1, R2 = Open; C1, C2 = Open
2.9
4.5
VSDA1, VSCL1 = GND1; VSDA2, VSCL2 = GND2;
R1, R2 = Open; C1, C2 = Open
2.3
3.7
VSDA1, VSCL1 = VCC1; VSDA2, VSCL2 = VCC2;
R1, R2 = Open; C1, C2 = Open
2.5
4
UNIT
3 V ≤ VCC1, VCC2 ≤ 3.6 V
ISO1540-Q1
ICC1
Supply current, side 1
ISO1541-Q1
ICC2
Supply current, side 2
ISO1540-Q1 and
ISO1541-Q1
mA
mA
4.5 V ≤ VCC1, VCC2 ≤ 5.5 V
ISO1540-Q1
ICC1
Supply current, side 1
ISO1541-Q1
ICC2
Supply current, side 2
ISO1540-Q1 and
ISO1541-Q1
mA
mA
6.11 Timing Requirements
tSP
Input noise filter
tUVLO
Time to recover from UVLO
2.7 V to 0.9 V; See Figure 22
MIN
NOM
5
12
30
50
MAX
UNIT
110
µs
ns
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
9
ISO1540-Q1, ISO1541-Q1
SLLSEX0 – NOVEMBER 2016
www.ti.com
6.12 Switching Characteristics
over recommended operating conditions, unless otherwise noted
PARAMETER
TEST CONDITIONS
MIN
TYP MAX
UNIT
3 V ≤ VCC1, VCC2 ≤ 3.6 V
Output Signal Fall Time
(SDA1, SCL1)
See Figure 19
R1 = 953 Ω,
C1 = 40 pF
0.7 × VCC1 to 0.3 × VCC1
tf1
tf2
Output Signal Fall Time
(SDA2, SCL2)
See Figure 19
R2 = 95.3 Ω,
C2 = 400 pF
tpLH1-2
Low-to-High Propagation
Delay, Side 1 to Side 2
tPHL1-2
High-to-Low Propagation
Delay, Side 1 to Side 2
PWD1-2
Pulse Width Distortion
|tpHL1-2 – tpLH1-2|
tPLH2-1 (1)
Low-to-High Propagation
Delay, Side 2 to Side 1
tPHL2-1 (1)
High-to-Low Propagation
Delay, Side 2 to Side 1
PWD2-1 (1)
Pulse Width Distortion
|tpHL2-1 – tpLH2-1|
tLOOP1 (1)
Round-trip propagation
delay on Side 1
See Figure 19
R1 = 953 Ω,
R2 = 95.3 Ω,
C1, C2 = 10 pF
See Figure 20;
R1 = 953 Ω, C1 = 40 pF
R2 = 95.3 Ω, C2 = 400 pF
8
17
29
0.9 × VCC1 to 900 mV
16
29
48
0.7 × VCC2 to 0.3 × VCC2
14
23
47
0.9 × VCC2 to 400 mV
35
50
100
0.55 V to 0.7 × VCC2
33
65
ns
0.7 V to 0.4 V
90
181
ns
55
123
ns
0.4 × VCC2 to 0.7 × VCC1
47
68
ns
0.4 × VCC2 to 0.9 V
67
109
ns
20
49
ns
100
165
ns
6
11
20
0.4 V to 0.3 × VCC1
ns
ns
4.5 V ≤ VCC1, VCC2 ≤ 5.5 V
Output Signal Fall Time
(SDA1, SCL1)
See Figure 19
R1 = 1430 Ω,
C1 = 40 pF
0.7 × VCC1 to 0.3 × VCC1
tf1
0.9 × VCC1 to 900 mV
13
21
39
Output Signal Fall Time
(SDA2, SCL2)
See Figure 19
R2 = 143 Ω,
C2 = 400 pF
0.7 × VCC2 to 0.3 × VCC2
10
18
35
tf2
0.9 × VCC2 to 400 mV
28
41
76
tpLH1-2
Low-to-High Propagation
Delay, Side 1 to Side 2
0.55 V to 0.7 × VCC2
31
62
ns
tPHL1-2
High-to-Low Propagation
Delay, Side 1 to Side 2
0.7 V to 0.4 V
70
139
ns
PWD1-2
Pulse Width Distortion
|tpHL1-2 – tpLH1-2|
38
80
ns
tPLH2-1 (1)
Low-to-high propagation
delay, side 2 to side 1
0.4 × VCC2 to 0.7 × VCC1
55
80
ns
tPHL2-1 (1)
High-to-low propagation
delay, Side 2 to side 1
0.4 × VCC2 to 0.9 V
47
85
ns
PWD2-1 (1)
Pulse Width Distortion
|tpHL2-1 – tpLH2-1|
8
21
ns
tLOOP1 (1)
Round-trip propagation
delay on side 1
110
180
ns
(1)
10
See Figure 19
R1 = 1430 Ω,
R2 = 143 Ω,
C1,2 = 10 pF
See Figure 20;
R1 = 1430 Ω, C1 = 40 pF
R2 = 143 Ω, C2 = 400 pF
0.4 V to 0.3 × VCC1
ns
ns
This parameter does not apply to the ISO1541-Q1 SCL1 line as it is unidirectional.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
ISO1540-Q1, ISO1541-Q1
www.ti.com
SLLSEX0 – NOVEMBER 2016
6.13 Insulation Characteristics Curves
350
VCC1 = VCC2 = 3.6 V
VCC1 = VCC2 = 5.5 V
Safety Limiting Current (mA)
300
250
200
150
100
50
0
0
50
100
150
Ambient Temperature (qC)
200
Figure 1. Thermal Derating Curve for Limiting Current per VDE
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
11
ISO1540-Q1, ISO1541-Q1
SLLSEX0 – NOVEMBER 2016
www.ti.com
6.14 Typical Characteristics
3.0
0.800
IOL1 = 3.5 mA
IOL1 = 0.5 mA
2.5
0.760
Output Current, IOL1 (mA)
Output Voltage, VOL1 (V)
0.780
0.740
0.720
0.700
0.680
0.660
0.640
2.0
1.5
1.0
0.5
0.0
0.620
-0.5
0
0.600
−40 −25 −10
5
20 35 50 65 80
Free−Air Temperature (°C)
95
0.4
0.5
0.6
20
20
18
18
16
16
14
14
12
10
8
6
-25
-10
VCC1 = 3.3 V
0.9
R1 = 1430 :
R1 = 2.2 k:
12
10
8
6
5
20 35 50 65 80
Free-Air Temperature (qC)
95
2
0
-40
110 125
-25
-10
5
D001
C1 = 40 pF
Fall time measured from 70% to 30% VCC1
VCC1 = 5 V
Figure 4. Side 1: Output Fall Time vs Free-Air Temperature
25
25
Fall Time tf2 (ns)
30
20
15
10
20 35 50 65 80
Free-Air Temperature (qC)
95
110 125
D002
C1 = 40 pF
Fall time measured from 70% to 30% VCC1
Figure 5. Side 1: Output Fall Time vs Free-air Temperature
30
5
20
15
10
5
R2 = 95.3 :
R2 = 2.2 k:
-25
-10
VCC2 = 3.3 V
5
20 35 50 65 80
Free-Air Temperature (qC)
95
R2 = 143 :
R2 = 2.2 k:
110 125
0
-40
-25
-10
D003
C2 = 400 pF
Fall time measured from 70% to 30% VCC2
Figure 6. Side 2: Output Fall Time vs Free-Air Temperature
12
0.8
4
R1= 953 :
R1= 2.2 k:
2
0
-40
0.7
Figure 3. Side 1: Output Low Current vs SDA1 or SCL1
Applied Voltage
Fall Time, tf1 (ns)
Fall Time, tf1 (ns)
0.3
TA = 25°C
4
Fall Time tf2 (ns)
0.2
Applied Voltage, VSDA1, VSCL1 (V)
Figure 2. Side 1: Output Low Voltage vs Free-Air
Temperature
0
-40
0.1
110 125
VCC2 = 5 V
5
20 35 50 65 80
Free-Air Temperature (qC)
95
110 125
D004
C2 = 400 pF
Fall time measured from 70% to 30% VCC2
Figure 7. Side 2: Output Fall Time vs Free-Air Temperature
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
ISO1540-Q1, ISO1541-Q1
www.ti.com
SLLSEX0 – NOVEMBER 2016
Typical Characteristics (continued)
120
45
100
Propagation Delay, tPHL1-2 (ns)
Propagation Delay, t PLH1-2 (ns)
40
35
30
25
20
15
10
80
60
40
20
VCC1 and VCC2 = 3.3 V, R2 = 95.3 :
VCC1 and VCC2 = 5 V, R2 = 143 :
VCC1 and VCC2 = 3.3 V, R2 = 95.3 :
VCC1 and VCC2 = 5 V, R2 = 143 :
5
0
-40
-25
-10
5
20 35 50 65 80
Free-Air Temperature (qC)
95
0
-40
110 125
C2 = 10 pF
5
20 35 50 65 80
Free-Air Temperature (qC)
95
110 125
D006
Figure 9. tPHL1-2 Propagation Delay vs Free-Air Temperature
1050
90
VCC1 and VCC2 = 3.3 V
VCC1 and VCC2 = 5 V
1045
80
Propagation Delay, t PHL1-2 (ns)
Propagation Delay, tPLH1-2 (ns)
-10
C2 = 10 pF
Figure 8. tPLH1-2 Propagation Delay vs Free-Air Temperature
1040
1035
1030
1025
1020
1015
1010
70
60
50
40
30
20
VCC1 and VCC2 = 3.3 V
VCC1 and VCC2 = 5 V
10
1005
1000
-40
-25
-10
5
R2 = 2.2 kΩ
20 35 50 65 80
Free-Air Temperature (qC)
95
0
-40
110 125
C2 = 400 pF
70
Propagation Delay, t PHL2-1 (ns)
60
50
40
30
20
-10
5
20 35 50 65 80
Free-Air Temperature (qC)
95
110 125
95
110 125
D008
60
50
40
30
20
VCC1 and VCC2 = 3.3 V, R1 = 953 :
VCC1 and VCC2 = 5 V, R1 = 1430 :
0
-40
-25
-10
D009
C1 = 10 pF
20 35 50 65 80
Free-Air Temperature (qC)
C2 = 400 pF
10
VCC1 and VCC2 = 3.3 V, R1 = 953 :
VCC1 and VCC2 = 5 V, R1 = 1430 :
-25
5
Figure 11. tPHL1-2 Propagation Delay vs Free-Air
Temperature
80
0
-40
-10
R2 = 2.2 kΩ
70
10
-25
D007
Figure 10. tPLH1-2 Propagation Delay vs Free-Air
Temperature
Propagation Delay, t PHL2-1 (ns)
-25
D005
5
20 35 50 65 80
Free-Air Temperature (qC)
95
110 125
D010
C1 = 10 pF
Figure 12. tPLH2-1 Propagation Delay vs Free-Air
Temperature
Figure 13. tPHL2-1 Propagation Delay vs Free-Air
Temperature
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
13
ISO1540-Q1, ISO1541-Q1
SLLSEX0 – NOVEMBER 2016
www.ti.com
148
80
146
70
Propagation Delay, t PHL2-1 (ns)
Propagation Delay, tPLH2-1 (ns)
Typical Characteristics (continued)
144
142
140
138
136
134
VCC1 and VCC2 = 3.3 V
VCC1 and VCC2 = 5 V
132
-40
-25
-10
5
R1 = 2.2 kΩ
20 35 50 65 80
Free-Air Temperature (qC)
95
60
50
40
30
20
VCC1 and VCC2 = 3.3 V
VCC1 and VCC2 = 5 V
10
0
−40 −25 −10
110 125
D011
C1 = 40 pF
R1 = 2.2 kΩ
Figure 14. tPLH2-1 Propagation Delay vs Free-Air
Temperature
5
20 35 50 65 80
Free-Air Temperature (°C)
C1 = 40 pF
95
110 125
Figure 15. tPHL2-1 Propagation Delay vs Free-Air
Temperature
600
140
120
595
tLOOP1 (ns)
tLOOP1 (ns)
100
80
60
590
585
40
580
20
VCC1 and VCC2 = 3.3 V
VCC1 and VCC2 = 5 V
VCC1 and VCC2 = 3.3 V, R1 = 953 :, R2 = 95.3 :
VCC1 and VCC2 = 5 V, R1 = 1430 :, R2 = 143 :
0
-40
-25
-10
C1 = 40 pF
5
20 35 50 65 80
Free-Air Temperature (qC)
95
110 125
575
-40
-25
C2 = 400 pF
5
20 35 50 65 80
Free-Air Temperature (qC)
C1 = 40 pF
R1 = 2.2 kΩ
Figure 16. tLOOP1 vs Free-Air Temperature
Common-Mode Transient Immunity (kV/Ps)
-10
D013
95
110 125
D014
C2 = 400 pF
R2 = 2.2 kΩ
Figure 17. tLOOP1 vs Free-Air Temperature
70
60
50
40
30
20
10
VCC1 and VCC2 = 3.3 V
VCC1 and VCC2 = 5 V
0
-40
-25
-10
5
20 35 50 65 80
Free-Air Temperature (qC)
95
110 125
D015
Figure 18. CMTI vs Free-Air Temperature
14
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
ISO1540-Q1, ISO1541-Q1
www.ti.com
SLLSEX0 – NOVEMBER 2016
7 Parameter Measurement Information
±
+
±
+
VCC1
R1
R1
VCC2
R2
SDA1
R2
SDA2
ISO1540
ISO1541
SCL2
SCL1
C1
C1
C2
C2
Copyright © 2016, Texas Instruments Incorporated
Figure 19. Test Diagram
VCC2
VCC1
SDA1 or
SCL1
Output
R1
Isolation
VCC1
GND1
C1
tLOOP1
0.3 VCC1
SDA1
SCL1 (ISO1540 Only)
0.4 V
GND1
Copyright © 2016, Texas Instruments Incorporated
Figure 20. tLoop1 Setup and Timing Diagram
VCCx
VCCy
2k
2k
Input
Isolation
+
Output
±
GNDx
GNDy
VCMTI
Figure 21. Common-Mode Transient Immunity Test Circuit
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
15
ISO1540-Q1, ISO1541-Q1
SLLSEX0 – NOVEMBER 2016
www.ti.com
Parameter Measurement Information (continued)
VCCy
VCCx
VCCx
Ry
SDAx or
SCLx
I solatio n
0V
Side x, Side y VCCx,VCCy
Ry
1, 2
3.3 V, 3.3 V 95.3 Ω
2, 1
3.3 V, 3.3 V 953 Ω
+
Output
GNDy
GNDx
or
VCCx
VCCy
VCCy
Ry
SDAx or
SCLx
Isola tion
0V
+
Output
GNDx
GNDy
VCCx or
VCCy
2 .7 V
t
UVLO
0 .9 V
Output
Figure 22. tUVLO Test Circuit and Timing Diagrams
16
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
ISO1540-Q1, ISO1541-Q1
www.ti.com
SLLSEX0 – NOVEMBER 2016
8 Detailed Description
8.1 Overview
The I2C bus is used in a wide range of applications because it is simple to use. The bus consists of a two-wire
communication bus that supports bidirectional data transfer between a master device and several slave devices.
The master, or processor, controls the bus, specifically the serial clock (SCL) line. Data is transferred between
the master and slave through a serial data (SDA) line. This data can be transferred in four speeds: standard
mode (0 to 100 kbps), fast mode (0 to 400 kbps), fast-mode plus (0 to 1 Mbps), and high-speed mode (0 to 3.4
Mbps). The most common speeds are the standard and fast modes.
The I2C bus operates in bidirectional, half-duplex mode, while standard digital isolators are unidirectional devices.
To make efficient use of one technology supporting the other, external circuitry is required that separates the
bidirectional bus into two unidirectional signal paths without introducing significant propagation delay. These
devices have their logic input and output buffers separated by TI's capacitive isolation technology using a silicon
dioxide (SiO2) barrier. When used in conjunction with isolated power supplies, these devices block high voltages,
isolate grounds, and prevent noise currents from entering the local ground and interfering with or damaging
sensitive circuitry.
8.2 Functional Block Diagrams
VCC1
VCC2
SDA2
VREF
Isolation Capacitor
SDA1
SCL1
SCL2
GND1
GND2
VREF
Figure 23. ISO1540-Q1 Block Diagram
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
17
ISO1540-Q1, ISO1541-Q1
SLLSEX0 – NOVEMBER 2016
www.ti.com
Functional Block Diagrams (continued)
VCC2
SDA1
SDA2
Isolation Capacitor
VCC1
VREF
SCL1
SCL2
GND1
GND2
Figure 24. ISO1541-Q1 Block Diagram
8.3 Feature Description
The device enables a complete isolated I2C interface to be implemented within a small form factor having the
features listed in Table 1.
Table 1. Features List
(1)
PART NUMBER
CHANNEL DIRECTION
ISO1540-Q1
Bidirectional (SCL)
Bidirectional (SDA)
ISO1541-Q1
Unidirectional (SCL)
Bidirectional (SDA)
RATED ISOLATION (1)
MAXIMUM FREQUENCY
2500 VRMS
4242 VPK
1 MHz
See Safety-Related Certifications for detailed Isolation specifications.
8.4 Isolator Functional Principle
To isolate a bidirectional signal path (SDA or SCL), the ISO1540-Q1 internally splits a bidirectional line into two
unidirectional signal lines, each of which is isolated through a single-channel digital isolator. Each channel output
is made open-drain to comply with the open-drain technology of I2C. Side 1 of the ISO1540-Q1 connects to a
low-capacitance I2C node, while side 2 is designed for connecting to a fully loaded I2C bus with up to 400 pF of
capacitance.
VCC1
VCC2
A
R PU1
R PU2
B
SDA1
ISO1540
Cnode
VC-out
SDA2
40 mV
Cbus
C
50 mV
VSDA1
D
GND1
V REF
GND2
VILT1
VIHT1
VOL1
Copyright © 2016, Texas Instruments Incorporated
Figure 25. SDA Channel Design and Voltage Levels at SDA1
18
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
ISO1540-Q1, ISO1541-Q1
www.ti.com
SLLSEX0 – NOVEMBER 2016
Isolator Functional Principle (continued)
At first sight, the arrangement of the internal buffers suggests a closed signal loop that is prone to latch-up.
However, this loop is broken by implementing an output buffer (B) whose output low-level is raised by a diode
drop to approximately 0.75 V, and the input buffer (C) that consists of a comparator with defined hysteresis. The
comparator’s upper and lower input thresholds then distinguish between the proper low-potential of 0.4 V
(maximum) driven directly by SDA1 and the buffered output low-level of B.
Figure 26 demonstrate the switching behavior of the I2C isolator, ISO1540-Q1, between a master node at SDA1
and a heavy loaded bus at SDA2.
VCC2
VOL1
SDA1
50%
SDA2
VIHT1
30%
Receive
Delay
Receive
Delay
VCC1
Receive
Delay
Transmit
Delay
VCC1
VCC2
VCC2
SDA2
50%
SDA1
VCC1
VCC1
VCC2
Transmit
Delay
VIHT2
30%
Figure 26. SDA Channel Timing in Receive and Transmit Directions
8.4.1 Receive Direction (Left Diagram of Figure 26)
When the I2C bus drives SDA2 low, SDA1 follows after a certain delay in the receive path. The output low is the
buffered output of VOL1 = 0.75 V, which is sufficiently low to be detected by Schmitt-trigger inputs with a minimum
input-low voltage of VIL = 0.9 V at 3 V supply levels.
When SDA2 is released, its voltage potential increases towards VCC2 following the time-constant formed by
RPU2 and Cbus. After the receive delay, SDA1 is released and also rises towards VCC1, following the timeconstant RPU1 × Cnode. Because of the significant lower time-constant, SDA1 may reach VCC1 before SDA2
reaches VCC2 potential.
8.4.2 Transmit Direction (Right Diagram of Figure 26)
When a master drives SDA1 low, SDA2 follows after a certain delay in the transmit direction. When SDA2 turns
low it also causes the output of buffer B to turn low but at a higher 0.75 V level. This level cannot be observed
immediately as it is overwritten by the lower low-level of the master.
However, when the master releases SDA1, the voltage potential increases and first must pass the upper input
threshold of the comparator, VIHT1, to release SDA2. SDA1 then increases further until it reaches the buffered
output level of VOL1 = 0.75 V, maintained by the receive path. When comparator C turns high, SDA2 is released
after the delay in transmit direction. It takes another receive delay until B’s output turns high and fully releases
SDA1 to move toward VCC1 potential.
8.5 Device Functional Modes
Table 2 lists the ISO154x-Q1 functional modes.
Table 2. Function Table (1)
(1)
(2)
POWER STATE
INPUT
OUTPUT
Z
VCC1 or VCC2 < 2.1 V
X
VCC1 and VCC2 > 2.8 V
L
L
VCC1 and VCC2 > 2.8 V
H
Z
VCC1 and VCC2 > 2.8 V
Z (2)
?
H = High Level; L = Low Level; Z = High Impedance or Float; X = Irrelevant; ? = Indeterminate
Invalid input condition as an I2C system requires that a pullup resistor to VCC is connected.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
19
ISO1540-Q1, ISO1541-Q1
SLLSEX0 – NOVEMBER 2016
www.ti.com
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
9.1.1 I2C Bus Overview
The inter-integrated circuit (I2C) bus is a single-ended, multi-master, 2-wire bus for efficient inter-IC
communication in half-duplex mode.
I2C uses open-drain technology, requiring two lines, serial data (SDA) and serial clock (SCL), to be connected to
VDD by resistors (see Figure 27). Pulling the line to ground is considered a logic zero while letting the line float is
a logic one. This logic is used as a channel access method. Transitions of logic states must occur while the SCL
pin is low. Transitions while the SCL pin is high indicate START and STOP conditions. Typical supply voltages
are 3.3 V and 5 V, although systems with higher or lower voltages are allowed.
VDD
RPU
RPU
RPU
RPU
RPU
RPU
RPU
RPU
SDA
SCL
SDA
SCL
GND
C
Master
SDA
SCL
SDA
GND
ADC
Slave
SCL
GND
DAC
Slave
SDA
SCL
GND
C
Slave
Figure 27. I2C Bus
I2C communication uses a 7-bit address space with 16 reserved addresses, so a theoretical maximum of 112
nodes can communicate on the same bus. In praxis, however, the number of nodes is limited by the specified,
total bus capacitance of 400 pF, which restricts communication distances to a few meters.
The specified signaling rates for the ISO1540-Q1 and ISO1541-Q1 devices are 100 kbps (standard mode), 400
kbps (fast mode), 1 Mbps (fast mode plus).
The bus has two roles for nodes: master and slave. A master node issues the clock and slave addresses, and
also initiates and ends data transactions. A slave node receives the clock and addresses and responds to
requests from the master. Figure 28 shows a typical data transfer between master and slave.
20
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
ISO1540-Q1, ISO1541-Q1
www.ti.com
SLLSEX0 – NOVEMBER 2016
Application Information (continued)
7-bit
ADDRESS
SDA
SCL
1 -7
R/W
ACK
8
9
8-bit
DATA
8-bit
DATA
ACK
1 -8
9
ACK /
NACK
1 -8
9
S
P
START
Condition
STOP
condition
Figure 28. Timing Diagram of a Complete Data Transfer
The master initiates a transaction by creating a START condition, following by the 7-bit address of the slave it
wishes to communicate with. This is followed by a single read and write (R/W) bit, representing whether the
master wishes to write to 0, or to read from 1 the slave. The master then releases the SDA line to allow the slave
to acknowledge the receipt of data.
The slave responds with an acknowledge bit (ACK) by pulling the SDA pin low during the entire high time of the
9th clock pulse on the SCL signal, after which the master continues in either transmit or receive mode (according
to the R/W bit sent), while the slave continues in the complementary mode (receive or transmit, respectively).
The address and the 8-bit data bytes are sent most significant bit (MSB) first. The START bit is indicated by a
high-to-low transition of SDA while SCL is high. The STOP condition is created by a low-to-high transition of SDA
while SCL is high.
If the master writes to a slave, it repeatedly sends a byte with the slave sending an ACK bit. In this case, the
master is in master-transmit mode and the slave is in slave-receive mode.
If the master reads from a slave, it repeatedly receives a byte from the slave, while acknowledging (ACK) the
receipt of every byte but the last one (see Figure 29). In this situation, the master is in master-receive mode and
the slave is in slave-transmit mode.
The master ends the transmission with a STOP bit, or may send another START bit to maintain bus control for
further transfers.
S Slave Address W A
From Master to Slave
DATA
A
DATA
A P
A = acknowledge
A = not acknowledge
Master Transmitter writing to Slave Receiver
S = Start
From Slave to Master
P = Stop
S Slave Address R A
DATA
A
DATA
Master Receiver reading from Slave Transmitter
A P
R = Read
W = Write
Figure 29. Transmit or Receive Mode Changes During a Data Transfer
When writing to a slave, a master mainly operates in transmit-mode and only changes to receive-mode when
receiving acknowledgment from the slave.
When reading from a slave, the master starts in transmit-mode and then changes to receive-mode after sending
a READ request (R/W bit = 1) to the slave. The slave continues in the complementary mode until the end of a
transaction.
NOTE
The master ends a reading sequence by not acknowledging (NACK) the last byte
received. This procedure resets the slave state machine and allows the master to send
the STOP command.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
21
ISO1540-Q1, ISO1541-Q1
SLLSEX0 – NOVEMBER 2016
www.ti.com
9.2 Typical Application
Figure 30 shows isolated I2C data acquisition system built with TI microcontroller, analog-to-digital converter, and
I2C isolator, ISO1541-Q1.
The entire circuit operates from a single 3.3-V supply. A low-power push-pull converter, SN6501-Q1, drives a
center-tapped transformer with an output that is rectified and linearly regulated to provide a stable 5-V supply for
the data converter.
VS
0.1 F
3.3 V
2
Vcc
D2
1:2.2
3
MBR0520L
6,7
10 F 0.1 F
D1
1
10 F
GND
4
OUT
13,14
5VISO
TPS76750-Q1
SN6501-Q1
GND
IN
5
GND
EN
10 F
3
MBR0520L
5
ISO Barrier
1.5 k
1.5 k
1.5 k
0.1 F
1.5 k
5VISO
0.1 F
0.1 F
43
1
VDD
41
X1
40
X2
SDA 2
TMS320F28035PAGQ SCL 3
2
VCC2
7
SDA2
ISO1541-Q1
6
3
SCL1
SCL2
SDA1
GND1
VSS
42
8
8
VCC1
4
VDD
9
10
1
GND2
4
AIN0
SDA
4 Analog
Inputs
ADS1115-Q1
SCL
ADDR
5
AIN3
GND
3
7
Copyright © 2016, Texas Instruments Incorporated
Figure 30. Isolated I2C Data Acquisition System
9.2.1 Design Requirements
The recommended power supply voltages (VCC1 and VCC2) must be from 3 V to 5.5 V. A recommended
decoupling capacitor with a value of 0.1 µF is required between both the VCC1 and GND1 pins, and the VCC2
and GND2 pins to support of power supply voltages transient and to ensure reliable operation at all data rates.
9.2.2 Detailed Design Procedure
The power-supply capacitor with a value of 0.1-µF must be placed as close to the power supply pins as possible.
The recommended placement of the capacitors must be 2-mm maximum from input and output power supply
pins (VCC1 and VCC2).
The maximum load permissible on the input lines, SDA1 and SCL1, is ≤ 40 pF and on the output lines, SDA2
and SCL2, is ≤ 400 pF.
The minimum pullup resistors on the input lines, SDA1 and SCL1 to VCC1 must be selected in such a way that
input current drawn is ≤ 3.5 mA. The minimum pullup resistors on the input lines, SDA2 and SCL2, to VCC2 must
be selected in such a way that output current drawn is ≤ 35 mA. The maximum pullup resistors on the input lines
(SDA1 and SCL1) to VCC1 and on output lines (SDA1 and SCL1) to VCC2, depends on the load and rise time
requirements on the respective lines.
22
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
ISO1540-Q1, ISO1541-Q1
www.ti.com
SLLSEX0 – NOVEMBER 2016
Typical Application (continued)
ISO1540-Q1
2mm
maximum
2 mm
maximum
VCC1
VCC2
8
1
10 …F
1k
SDA1
10 …F
Isolation Capacitor
1k
2
SCL1
3
1k
1k
SDA2
7
SCL2
6
GND1
4
GND2
5
Side 1
Side 2
Copyright © 2016, Texas Instruments Incorporated
Figure 31. Typical ISO1540-Q1 Circuit Hookup
ISO1541-Q1
2mm
maximum
2 mm
maximum
VCC1
VCC2
8
1
10 …F
1k
SDA1
10 …F
Isolation Capacitor
1k
2
SCL1
3
1k
1k
SDA2
7
SCL2
6
GND1
4
GND2
5
Side 1
Side 2
Copyright © 2016, Texas Instruments Incorporated
Figure 32. Typical ISO1541-Q1 Circuit Hookup
9.2.3 Application Curve
o
500 mV/div
TA = 25 C
VCC1 = 3.6 V
900 mV
VOL1
GND1
Time - 50 ns/div
Figure 33. Side 1: Low-to-High Transition
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
23
ISO1540-Q1, ISO1541-Q1
SLLSEX0 – NOVEMBER 2016
www.ti.com
10 Power Supply Recommendations
To help ensure reliable operation at data rates and supply voltages, TI recommends connecting a 0.1-µF bypass
capacitor at the input and output supply pins (VCC1 and VCC2). The capacitors should be placed as close to the
supply pins as possible. If only a single, primary-side power supply is available in an application, isolated power
can be generated for the secondary-side with the help of a transformer driver such as TI's SN6501-Q1 device.
For such applications, detailed power supply design and transformer selection recommendations are available in
SN6501-Q1 Transformer Driver for Isolated Power Supplies (SLLSEF3).
11 Layout
11.1 Layout Guidelines
A minimum of four layers is required to accomplish a low EMI PCB design (see Figure 34). Layer stacking should
be in the following order (top-to-bottom): high-speed signal layer, ground plane, power plane and low-frequency
signal layer.
• Routing the high-speed traces on the top layer avoids the use of vias (and the introduction of their
inductances) and allows for clean interconnects between the isolator and the transmitter and receiver circuits
of the data link.
• Placing a solid ground plane next to the high-speed signal layer establishes controlled impedance for
transmission line interconnects and provides an excellent low-inductance path for the return current flow.
• Placing the power plane next to the ground plane creates additional high-frequency bypass capacitance of
approximately 100 pF/in2.
• Routing the slower speed control signals on the bottom layer allows for greater flexibility as these signal links
usually have margin to tolerate discontinuities such as vias.
If an additional supply voltage plane or signal layer is needed, add a second power or ground plane system to
the stack to keep it symmetrical. This makes the stack mechanically stable and prevents it from warping. Also the
power and ground plane of each power system can be placed closer together, thus increasing the high-frequency
bypass capacitance significantly.
For detailed layout recommendations, see the Digital Isolator Design Guide (SLLA284)
11.1.1 PCB Material
For digital circuit boards operating at less than 150 Mbps, (or rise and fall times greater than 1 ns), and trace
lengths of up to 10 inches, use standard FR-4 UL94V-0 printed circuit board. This PCB is preferred over cheaper
alternatives because of lower dielectric losses at high frequencies, less moisture absorption, greater strength and
stiffness, and the self-extinguishing flammability-characteristics.
11.2 Layout Example
High-speed traces
10 mils
Ground plane
40 mils
Keep this
space free
from planes,
traces, pads,
and vias
FR-4
0r ~ 4.5
Power plane
10 mils
Low-speed traces
Figure 34. Recommended Layer Stack
24
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
ISO1540-Q1, ISO1541-Q1
www.ti.com
SLLSEX0 – NOVEMBER 2016
12 Device and Documentation Support
12.1 Documentation Support
12.1.1 Related Documentation
For related documentation see the following:
• Digital Isolator Design Guide (SLLA284)
• TI Isolation Glossary (SLLA353)
• SN6501-Q1 Transformer Driver for Isolated Power Supplies. (SLLSEF3)
• TPS767xx-Q1 Fast-Transient-Response 1-A Low-Dropout Voltage Regulators (SGLS009)
• ADS1115-Q1 Low-Power, 16-Bit Analog-to-Digital Converter With Internal Reference (SBAS563)
• TMS320F2803x Piccolo™ Microcontrollers (TMS320F2803x Piccolo™ Microcontrollers)
12.2 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 3. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
ISO1540-Q1
Click here
Click here
Click here
Click here
Click here
ISO1541-Q1
Click here
Click here
Click here
Click here
Click here
12.3 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
12.4 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.5 Trademarks
Piccolo, E2E are trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
12.6 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
12.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
25
ISO1540-Q1, ISO1541-Q1
SLLSEX0 – NOVEMBER 2016
www.ti.com
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
26
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: ISO1540-Q1 ISO1541-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
9-Dec-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
ISO1540QDQ1
PREVIEW
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
I1540Q
ISO1540QDRQ1
PREVIEW
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
I1540Q
ISO1541QDQ1
PREVIEW
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
I1541Q
ISO1541QDRQ1
PREVIEW
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
I1541Q
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
9-Dec-2016
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF ISO1540-Q1, ISO1541-Q1 :
• Catalog: ISO1540, ISO1541
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
Addendum-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated
Similar pages