TI1 LP2998MRE/NOPB Ddr termination regulator Datasheet

Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
LP2998, LP2998-Q1
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
LP2998/LP2998-Q1 DDR Termination Regulator
1 Features
3 Description
•
The LP2998 linear regulator is designed to meet
JEDEC SSTL-2 and JEDEC SSTL-18 specifications
for termination of DDR-SDRAM and DDR2 memory.
The device also supports DDR3 and DDR3L VTT bus
termination with VDDQ min of 1.35 V. The device
contains a high-speed operational amplifier to provide
excellent response to load transients. The output
stage prevents shoot through while delivering 1.5 A
continuous current and transient peaks up to 3 A in
the application as required for DDR-SDRAM
termination. The LP2998 also incorporates a
VSENSE pin to provide superior load regulation and
a VREF output as a reference for the chipset and
DIMMs.
1
•
•
•
•
•
•
•
•
AEC-Q100 Test Guidance with the following
results (SO PowerPAD-8):
– Device HBM ESD Classification Level H1C
– Junction Temperature Range –40°C to 125°C
1.35 V Minimum VDDQ
Source and Sink Current
Low Output Voltage Offset
No External Resistors Required
Linear Topology
Suspend to Ram (STR) Functionality
Low External Component Count
Thermal Shutdown
An additional feature found on the LP2998 is an
active low shutdown (SD) pin that provides Suspend
To RAM (STR) functionality. When SD is pulled low
the VTT output will tri-state providing a high
impedance output, but, VREF will remain active. A
power savings advantage can be obtained in this
mode through lower quiescent current.
2 Applications
•
•
•
•
•
•
DDR1, DDR2, DDR3, and DDR3L Termination
Voltage
Automotive Infotainment
FPGA
Industrial/Medical PC
SSTL-18, SSTL-2, and SSTL-3 Termination
HSTL Termination
Device Information(1)
PART NUMBER
PACKAGE
BODY SIZE (NOM)
LP2998
SO PowerPAD™ (8) 4.89 mm x 3.90 mm
LP2998
SOIC (8)
LP2998-Q1
SO PowerPAD™ (8) 4.89 mm x 3.90 mm
4.90 mm x 3.91 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
4 Simplified Schematic
LP2998
VREF
SD
SD
VREF = 0.75V
+
VDDQ
VDDQ = 1.5V
AVIN
VDD = 2.5V
VSENSE
PVIN
CIN
+
CREF
VTT = 0.75V
VTT
GND
+
COUT
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LP2998, LP2998-Q1
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
www.ti.com
Table of Contents
1
2
3
4
5
6
Features ..................................................................
Applications ...........................................................
Description .............................................................
Simplified Schematic.............................................
Revision History.....................................................
Pin Configuration and Functions .........................
1
1
1
1
2
3
6.1 Pin Descriptions ........................................................ 3
7
Specifications......................................................... 5
7.1
7.2
7.3
7.4
7.5
7.6
7.7
8
Absolute Maximum Ratings .....................................
Handling Ratings: LP2998 ........................................
Handling Ratings: LP2998-Q1 ..................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
5
5
5
5
5
6
8
Detailed Description ............................................ 11
8.1 Overview ................................................................. 11
8.2 Functional Block Diagram ...................................... 11
8.3 Feature Description................................................. 11
8.4 Device Functional Modes........................................ 11
9
Application and Implementation ........................ 13
9.1 Application Information .......................................... 13
9.2 Typical Application .................................................. 15
10 Power Supply Recommendations ..................... 20
11 Layout................................................................... 20
11.1 Layout Guidelines ................................................. 20
11.2 Layout Examples................................................... 21
12 Device and Documentation Support ................. 22
12.1
12.2
12.3
12.4
Related Links ........................................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
22
22
22
22
13 Mechanical, Packaging, and Orderable
Information ........................................................... 22
5 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision J (December 2013) to Revision K
Page
•
Added DDR3 support throughout datasheet .......................................................................................................................... 1
•
Changed formatting to match new TI datasheet guidelines; added Device Information and Handling Ratings tables,
Power Supply, Layout Examples, and Device and Documentation Support sections; reformatted Detailed
Description and Application and Implementation sections. ................................................................................................... 1
•
Changed Electrical Char table condition statement .............................................................................................................. 6
•
Changed Electrical Char table condition statement .............................................................................................................. 7
Changes from Revision I (April 2013) to Revision J
Page
•
Added AEC-Q100 Test Guidance .......................................................................................................................................... 1
•
Changed layout of National Data Sheet to TI format ........................................................................................................... 20
2
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LP2998 LP2998-Q1
LP2998, LP2998-Q1
www.ti.com
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
6 Pin Configuration and Functions
SO PowerPAD
8-LEAD DDA
TOP VIEW
GND
1
8
VTT
SD
VSENSE
2
7
PVIN
3
6
VREF
4
5
AVIN
VDDQ
GND
SOIC
8-LEAD D
TOP VIEW
GND
1
8
VTT
SD
VSENSE
2
7
PVIN
3
6
VREF
4
5
AVIN
VDDQ
Pin Functions
PIN
NUMBER
TYPE
DESCRIPTION
1
GND
Ground
2
SD
3
VSENSE
Shutdown
4
VREF
Buffered internal reference voltage of VDDQ/2
5
VDDQ
Input for internal reference equal to VDDQ/2
6
AVIN
Analog input pin
7
PVIN
Power input pin
8
VTT
Output voltage for connection to termination resistors
EP
Exposed pad thermal connection. Connect to Ground.
Feedback pin for regulating VTT.
6.1 Pin Descriptions
AVIN AND PVIN
AVIN and PVIN are the input supply pins for the LP2998. AVIN is used to supply all the internal control circuitry. PVIN,
however, is used exclusively to provide the rail voltage for the output stage used to create VTT. These pins have the
capability to work off separate supplies depending on the application. Higher voltages on PVIN will increase the
maximum continuous output current because of output RDSON limitations at voltages close to VTT. The disadvantage
of high values of PVIN is that the internal power loss will also increase, thermally limiting the design. For SSTL-2
applications, a good compromise would be to connect the AVIN and PVIN directly together at 2.5 V. This eliminates the
need for bypassing the two supply pins separately. The only limitation on input voltage selection is that PVIN must be
equal to or lower than AVIN. It is recommended to connect PVIN to voltage rails equal to or less than 3.3 V to prevent
the thermal limit from tripping because of excessive internal power dissipation. If the junction temperature exceeds the
thermal shutdown than the part will enter a shutdown state identical to the manual shutdown where VTT is tri-stated and
VREF remains active.
VDDQ
VDDQ is the input used to create the internal reference voltage for regulating VTT. The reference voltage is generated
from a resistor divider of two internal 50 kΩ resistors. This ensures that VTT will track VDDQ / 2 precisely. The optimal
implementation of VDDQ is as a remote sense. This can be achieved by connecting VDDQ directly to the 2.5 V rail at
the DIMM instead of AVIN and PVIN. This ensures that the reference voltage tracks the DDR memory rails precisely
without a large voltage drop from the power lines. For SSTL-2 applications VDDQ will be a 2.5 V signal, which will
create a 1.25 V termination voltage at VTT (See Electrical Characteristics Table for exact values of VTT over
temperature).
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LP2998 LP2998-Q1
Submit Documentation Feedback
3
LP2998, LP2998-Q1
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
www.ti.com
Pin Descriptions (continued)
VSENSE
The purpose of the sense pin is to provide improved remote load regulation. In most motherboard applications the
termination resistors will connect to VTT in a long plane. If the output voltage was regulated only at the output of the
LP2998 then the long trace will cause a significant IR drop resulting in a termination voltage lower at one end of the bus
than the other. The VSENSE pin can be used to improve this performance, by connecting it to the middle of the bus. This
will provide a better distribution across the entire termination bus. If remote load regulation is not used then the VSENSE
pin must still be connected to VTT. Care should be taken when a long VSENSE trace is implemented in close proximity to
the memory. Noise pickup in the VSENSE trace can cause problems with precise regulation of VTT. A small 0.1 uF
ceramic capacitor placed next to the VSENSE pin can help filter any high frequency signals and preventing errors.
SHUTDOWN
The LP2998 contains an active low shutdown pin that can be used to tri-state VTT. During shutdown VTT should not be
exposed to voltages that exceed AVIN. With the shutdown pin asserted low the quiescent current of the LP2998 will
drop, however, VDDQ will always maintain its constant impedance of 100 kΩ for generating the internal reference.
Therefore, to calculate the total power loss in shutdown both currents need to be considered. For more information refer
to the Thermal Dissipation section. The shutdown pin also has an internal pull-up current, therefore to turn the part on
the shutdown pin can either be connected to AVIN or left open.
VREF
VREF provides the buffered output of the internal reference voltage VDDQ / 2. This output should be used to provide the
reference voltage for the Northbridge chipset and memory. Since these inputs are typically an extremely high
impedance, there should be little current drawn from VREF. For improved performance, an output bypass capacitor can
be used, located close to the pin, to help with noise. A ceramic capacitor in the range of 0.1 µF to 0.01 µF is
recommended. This output remains active during the shutdown state and thermal shutdown events for the suspend to
RAM functionality.
VTT
VTT is the regulated output that is used to terminate the bus resistors. It is capable of sinking and sourcing current while
regulating the output precisely to VDDQ / 2. The LP2998 is designed to handle peak transient currents of up to ± 3 A
with a fast transient response. The maximum continuous current is a function of VIN and can be viewed in the Typical
Characteristics section. If a transient is expected to last above the maximum continuous current rating for a significant
amount of time then the output capacitor should be sized large enough to prevent an excessive voltage drop. Despite
the fact that the LP2998 is designed to handle large transient output currents it is not capable of handling these for long
durations, under all conditions. The reason for this is the standard packages are not able to thermally dissipate the heat
as a result of the internal power loss. If large currents are required for longer durations, then care should be taken to
ensure that the maximum junction temperature is not exceeded. Proper thermal derating should always be used (please
refer to the Thermal Dissipation section). If the junction temperature exceeds the thermal shutdown point than VTT will
tri-state until the part returns below the hysteretic trip-point.
4
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LP2998 LP2998-Q1
LP2998, LP2998-Q1
www.ti.com
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
7 Specifications
7.1 Absolute Maximum Ratings
(1) (2)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
UNIT
−0.3
6
V
PVIN to GND
–0.3
AVIN
V
VDDQ (3)
−0.3
6
V
Junction temperature
150
°C
Lead temperature (soldering, 10 sec)
260
°C
AVIN to GND
(1)
(2)
(3)
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute–maximum–rated conditions for extended periods may affect device reliability.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
VDDQ voltage must be less than 2 x (AVIN - 1) or 6V, whichever is smaller.
7.2 Handling Ratings: LP2998
Tstg
Storage temperature range
V(ESD)
Electrostatic discharge
(1)
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all
pins (1)
MIN
MAX
UNIT
−65
150
°C
−1000
1000
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
7.3 Handling Ratings: LP2998-Q1
Tstg
Storage temperature range
V(ESD)
(1)
Electrostatic discharge
Human body model (HBM), per AEC Q100-002
(1)
MIN
MAX
UNIT
−65
150
°C
−1000
1000
V
AEC Q100-002 indicates HBM stressing is done in accordance with the ANSI/ESDA/JEDEC JS-001 specification. The LP2998-Q1 is
rated at AEC-Q100 ESD HBM Classification Level H1C.
7.4 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MAX
UNIT
Junction temperature (1)
MIN
–40
125
°C
AVIN to GND
2.2
5.5
V
PVIN supply voltage
0
AVIN
V
SD input voltage
0
AVIN
V
(1)
NOM
At elevated temperatures, devices must be derated based on thermal resistance.
7.5 Thermal Information
THERMAL METRIC (1)
RθJA
(1)
Junction-to-ambient thermal resistance
LP2998/LP2998-Q1
LP2998
SO PowerPAD
SOIC
8 PINS
8 PINS
43
151
UNIT
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LP2998 LP2998-Q1
Submit Documentation Feedback
5
LP2998, LP2998-Q1
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
www.ti.com
7.6 Electrical Characteristics
Typical limits tested at TJ = 25°C. Minimum and maximum limits apply over the full operating junction temperature range (TJ =
–40°C to 125°C). (1) Unless otherwise specified, AVIN = PVIN = 2.5 V, VDDQ = 2.5 V. (2)
PARAMETER
TEST CONDITIONS
VREF voltage (DDR I)
VREF
VREF voltage (DDR II)
VREF Voltage (DDR III)
ZVREF
VREF Output Impedance
MIN
TYP
MAX
VIN = VDDQ = 2.3 V
1.135
1.158
1.185
VIN = VDDQ = 2.5 V
1.235
1.258
1.285
VIN = VDDQ = 2.7 V
1.335
1.358
1.385
PVIN = VDDQ = 1.7 V
0.837
0.860
0.887
PVIN = VDDQ = 1.8 V
0.887
0.910
0.937
PVIN = VDDQ = 1.9 V
0.936
0.959
0.986
PVIN = VDDQ = 1.35V
0.669
0.684
0.699
PVIN = VDDQ = 1.5V
0.743
0.758
0.773
PVIN = VDDQ = 1.6V
0.793
0.808
0.823
IREF = –30 to 30 µA
2.5
UNIT
V
kΩ
IOUT = 0 A
VTT
VTT Output Voltage (DDR I)
(3)
VIN = VDDQ = 2.3 V
1.120
1.159
1.190
VIN = VDDQ = 2.5 V
1.210
1.259
1.290
VIN = VDDQ = 2.7 V
1.320
1.359
1.390
VIN = VDDQ = 2.3 V
1.125
1.159
1.190
VIN = VDDQ = 2.5 V
1.225
1.259
1.290
VIN = VDDQ = 2.7 V
1.325
1.359
1.390
PVIN = VDDQ = 1.7 V
0.822
0.856
0.887
PVIN = VDDQ = 1.8 V
0.874
0.908
0.939
PVIN = VDDQ = 1.9 V
0.923
0.957
0.988
PVIN = VDDQ = 1.7 V
0.820
0.856
0.890
PVIN = VDDQ = 1.8 V
0.870
0.908
0.940
PVIN = VDDQ = 1.9 V
0.920
0.957
0.990
PVIN = VDDQ = 1.35V
0.656
0.677
0.698
PVIN = VDDQ = 1.5 V
0.731
0.752
0.773
PVIN = VDDQ = 1.6 V
0.781
0.802
0.823
IOUT = 0.2 A, AVIN = 2.5V
PVIN = VDDQ = 1.35V
0.667
0.688
0.710
IOUT = -0.2A, AVIN = 2.5V
PVIN = VDDQ = 1.35V
0.641
0.673
0.694
IOUT = 0.4 A, AVIN = 2.5 V
PVIN = VDDQ = 1.5 V
0.740
0.763
0.786
IOUT = –0.4 A, AVIN = 2.5 V
PVIN = VDDQ = 1.5 V
0.731
0.752
0.773
IOUT = 0.5 A, AVIN = 2.5 V
PVIN = VDDQ = 1.6 V
0.790
0.813
0.836
IOUT = –0.5 A, AVIN = 2.5 V
PVIN = VDDQ = 1.6 V
0.781
0.802
0.823
IOUT = ±1.5 A
V
IOUT = 0 A, AVIN = 2.5 V
VTT Output Voltage (DDR II)
(3)
IOUT = ±0.5A, AVIN = 2.5 V
V
IOUT = 0A, AVIN = 2.5 V
VTT Output Voltage (DDR III)
(1)
(2)
(3)
6
(3)
V
Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlation using
Statistical Quality Control (SQC) methods. The limits are used to calculate Texas Instruments' Average Outgoing Quality Level (AOQL).
VIN is defined as VIN = AVIN = PVIN.
VTT load regulation is tested by using a 10 ms current pulse and measuring VTT.
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LP2998 LP2998-Q1
LP2998, LP2998-Q1
www.ti.com
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
Electrical Characteristics (continued)
Typical limits tested at TJ = 25°C. Minimum and maximum limits apply over the full operating junction temperature range (TJ =
–40°C to 125°C).(1) Unless otherwise specified, AVIN = PVIN = 2.5 V, VDDQ = 2.5 V.(2)
PARAMETER
TEST CONDITIONS
VTT Output Voltage Offset (VREF –
VTT) for DDR I (3)
VOSVtt
VTT Output Voltage Offset (VREF –
VTT) for DDR II (3)
VTT Output Voltage Offset (VREF –
VTT) for DDR III (3)
IQ
Quiescent Current
ZVDDQ
ISD
IQ_SD
Quiescent current in shutdown
30
IOUT = –1.5 A
–30
0
30
IOUT = 1.5 A
–30
0
30
IOUT = 0 A
–30
0
30
IOUT = –0.5 A
–30
0
30
IOUT = 0.5 A
–30
0
30
IOUT = 0 A
–30
0
30
IOUT = ±0.2 A
–30
0
30
IOUT = ±0.4 A
–30
0
30
IOUT = ±0.5 A
–30
0
30
320
500
Shutdown leakage current
Maximum Shutdown Low Level
Iv
VTT leakage current in shutdown
115
150
SD = 0 V
2
5
1.9
0.8
SD = 0 V
VTT = 1.25 V
1
10
13
(5)
165
Thermal Shutdown Hysteresis
mV
µA
kΩ
SD = 0 V
VSENSE Input current
Thermal Shutdown
UNIT
100
(4)
Minimum Shutdown High Level
TSD_HYS
MAX
0
VDDQ Input Impedance
VIL
TSD
TYP
–30
IOUT = 0 A
VIH
ISENSE
(4)
(5)
(4)
MIN
IOUT = 0 A
10
µA
V
µA
nA
°C
Quiescent current defined as the current flow into AVIN.
The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction to ambient thermal
resistance, RθJA, and the ambient temperature, TA. Exceeding the maximum allowable power dissipation will cause excessive die
temperature and the regulator will go into thermal shutdown.
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LP2998 LP2998-Q1
Submit Documentation Feedback
7
LP2998, LP2998-Q1
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
www.ti.com
7.7 Typical Characteristics
400
1050
350
900
300
750
250
600
IQ (uA)
IQ (uA)
Unless otherwise specified AVIN = PVIN = 2.5 V.
200
450
150
300
100
150
50
0
2
2.5
3
3.5
4
4.5
5
5.5
2
2.5
3
3.5
4
4.5
5
5.5
20
30
AVIN (V)
AVIN (V)
Figure 1. IQ vs AVIN In SD
Figure 2. IQ vs AvIN
4
1.40
3.5
1.35
3
VREF (V)
VSD (V)
1.30
2.5
2
1.25
1.20
1.5
1.15
1
0.5
2.5
3
3.5
4
4.5
5
-20
-10
0
10
AVIN (V)
IREF (uA)
Figure 3. VIH and VIL
Figure 4. VREF vs IREF
3
3
2.5
2.5
2
2
1.5
1.5
1
1
0.5
0.5
0
0
0
8
1.10
-30
5.5
VTT (V)
VREF (V)
2
1
2
3
4
5
6
0
1
2
3
4
5
VDDQ (V)
VDDQ (V)
Figure 5. VREF vs VDDQ
Figure 6. VTT vs VDDQ
Submit Documentation Feedback
6
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LP2998 LP2998-Q1
LP2998, LP2998-Q1
www.ti.com
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
Typical Characteristics (continued)
Unless otherwise specified AVIN = PVIN = 2.5 V.
400
1050
350
-40°C
750
250
25°C
85°C
200
IQ (PA)
300
ISD (PA)
25oC
900
-40oC
600
85oC
125oC
450
125°C
300
150
150
100
50
0
2
2
2.5
3
3.5
4
4.5
5
2.5
3
5.5
3.5
4
4.5
5
5.5
AVIN (V)
AVIN (V)
Figure 8. IQ vs AVIN Over Temperature
1.4
1.8
1.2
1.7
1
1.6
OUTPUT CURRENT (A)
OUTPUT CURRENT (A)
Figure 7. ISD vs AVIN Over Temperature
0.8
0.6
0.4
0.2
1.5
1.4
1.3
1.2
0
1.1
2
2.5
3
3.5
4
4.5
5
5.5
2
2.5
3
AVIN (V)
VDDQ = 2.5 V
3.5
4
4.5
5
5.5
AVIN (V)
PVIN = 1.8 V
VDDQ = 2.5 V
Figure 9. Maximum Sourcing Current vs AVIN
PVIN = 2.5 V
Figure 10. Maximum Sourcing Current vs AVIN
3.0
3
2.8
OUTPUT CURRENT (A)
OUTPUT CURRENT (A)
2.8
2.6
2.4
2.6
2.4
2.2
2.0
2.2
1.8
2
1.6
3
3.5
4
4.5
5
5.5
2
AVIN (V)
VDDQ = 2.5 V
2.5
3
3.5
4
4.5
5
5.5
AVIN (V)
PVIN = 3.3 V
VDDQ = 2.5 V
Figure 11. Maximum Sourcing Current vs AVIN
Figure 12. Maximum Sinking Current vs AVIN
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LP2998 LP2998-Q1
Submit Documentation Feedback
9
LP2998, LP2998-Q1
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
www.ti.com
Typical Characteristics (continued)
1.4
2.4
1.2
2.2
1
2
OUTPUT CURRENT (A)
OUTPUT CURRENT (A)
Unless otherwise specified AVIN = PVIN = 2.5 V.
0.8
0.6
0.4
0.2
1.8
1.6
1.4
1.2
0
1
2
2.5
3
3.5
4
4.5
5
5.5
2
2.5
AVIN (V)
VDDQ = 1.8 V
3
3.5
4
4.5
5
5.5
AVIN (V)
PVIN = 1.8 V
VDDQ = 1.8 V
Figure 13. Maximum Sourcing Current vs AVIN
Figure 14. Maximum Sinking Current vs AVIN
3
OUTPUT CURRENT (A)
2.8
2.6
2.4
2.2
2
3
3.5
4
4.5
5
5.5
AVIN (V)
VDDQ = 1.8 V
PVIN = 3.3 V
Figure 15. Maximum Sourcing Current vs AVIN
10
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LP2998 LP2998-Q1
LP2998, LP2998-Q1
www.ti.com
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
8 Detailed Description
8.1 Overview
The LP2998 linear regulator is designed to meet JEDEC SSTL-2 and JEDEC SSTL-18 specifications for
termination of DDR-SDRAM and DDR2 memory. The device also supports DDR3 and DDR3L VTT bus
termination with VDDQ min of 1.35 V. The device contains a high-speed operational amplifier to provide excellent
response to load transients. The output stage prevents shoot through while delivering 1.5 A continuous current
and transient peaks up to 3 A in the application as required for DDR-SDRAM termination.
8.2 Functional Block Diagram
VDDQ
SD
AVIN
PVIN
50k
VREF
+
-
50k
+
VTT
VSENSE
GND
8.3 Feature Description
The LP2998 is a linear bus termination regulator designed to meet the JEDEC requirements of SSTL-2 and
SSTL-18. The output, VTT is capable of sinking and sourcing current while regulating the output voltage equal to
VDDQ / 2. The output stage has been designed to maintain excellent load regulation while preventing shoot
through. The LP2998 also incorporates two distinct power rails that separates the analog circuitry from the power
output stage. This allows a split rail approach to be utilized to decrease internal power dissipation. It also permits
the LP2998 to provide a termination solution for DDR3-SDRAM and DDR3L-SDRAM memory.
8.4 Device Functional Modes
The LP2998 can also be used to provide a termination voltage for other logic schemes such as SSTL-3 or HSTL.
Series Stub Termination Logic (SSTL) was created to improve signal integrity of the data transmission across the
memory bus. This termination scheme is essential to prevent data error from signal reflections while transmitting
at high frequencies encountered with DDR-SDRAM. The most common form of termination is Class II single
parallel termination. This involves one RS series resistor from the chipset to the memory and one RT termination
resistor. Typical values for RS and RT are 25 Ω, although these can be changed to scale the current
requirements from the LP2998. This implementation can be seen below in Figure 16.
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LP2998 LP2998-Q1
Submit Documentation Feedback
11
LP2998, LP2998-Q1
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
www.ti.com
Device Functional Modes (continued)
VDD
VTT
RT
RS
MEMORY
CHIPSET
VREF
Figure 16. SSTL-Termination Scheme
12
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LP2998 LP2998-Q1
LP2998, LP2998-Q1
www.ti.com
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
9 Application and Implementation
9.1 Application Information
9.1.1 Input Capacitor
The LP2998 does not require a capacitor for input stability, but it is recommended for improved performance
during large load transients to prevent the input rail from dropping. The input capacitor should be located as
close as possible to the PVIN pin. Several recommendations exist dependent on the application required. A
typical value recommended for AL electrolytic capacitors is 50 µF. Ceramic capacitors can also be used, a value
in the range of 10 µF with X5R or better would be an ideal choice. The input capacitance can be reduced if the
LP2998 is placed close to the bulk capacitance from the output of the 2.5 V DC-DC converter. If the two supply
rails (AVIN and PVIN) are separated then the 47 uF capacitor should be placed as close to possible to the PVIN
rail. An additional 0.1 uF ceramic capacitor can be placed on the AVIN rail to prevent excessive noise from
coupling into the device.
9.1.2 Output Capacitor
The LP2998 has been designed to be insensitive of output capacitor size or ESR (Equivalent Series Resistance).
This allows the flexibility to use any capacitor desired. The choice for output capacitor will be determined solely
on the application and the requirements for load transient response of VTT. As a general recommendation the
output capacitor should be sized above 100 µF with a low ESR for SSTL applications with DDR-SDRAM. The
value of ESR should be determined by the maximum current spikes expected and the extent at which the output
voltage is allowed to droop. Several capacitor options are available on the market and a few of these are
highlighted below:
AL - It should be noted that many aluminum electrolytics only specify impedance at a frequency of 120 Hz, which
indicates they have poor high frequency performance. Only aluminum electrolytics that have an impedance
specified at a higher frequency (between 20 kHz and 100 kHz) should be used for the LP2998. To improve the
ESR several AL electrolytics can be combined in parallel for an overall reduction. An important note to be aware
of is the extent at which the ESR will change over temperature. Aluminum electrolytic capacitors can have their
ESR rapidly increase at cold temperatures.
Ceramic - Ceramic capacitors typically have a low capacitance, in the range of 10 to 100 µF range, but they have
excellent AC performance for bypassing noise because of very low ESR (typically less than 10 mΩ). However,
some dielectric types do not have good capacitance characteristics as a function of voltage and temperature.
Because of the typically low value of capacitance it is recommended to use ceramic capacitors in parallel with
another capacitor such as an aluminum electrolytic. A dielectric of X5R or better is recommended for all ceramic
capacitors.
Hybrid - Several hybrid capacitors such as OS-CON and SP are available from several manufacturers. These
offer a large capacitance while maintaining a low ESR. These are the best solution when size and performance
are critical, although their cost is typically higher than any other capacitor.
9.1.3 Thermal Dissipation
Since the LP2998 is a linear regulator any current flow from VTT will result in internal power dissipation
generating heat. To prevent damaging the part from exceeding the maximum allowable junction temperature,
care should be taken to derate the part dependent on the maximum expected ambient temperature and power
dissipation. The maximum allowable internal temperature rise (TRmax) can be calculated given the maximum
ambient temperature (TAmax) of the application and the maximum allowable junction temperature (TJmax).
TRmax = TJmax − TAmax
(1)
From this equation, the maximum power dissipation (PDmax) of the part can be calculated:
PDmax = TRmax / RθJA
(2)
The RθJA of the LP2998 will be dependent on several variables: the package used; the thickness of copper; the
number of vias and the airflow.
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LP2998 LP2998-Q1
Submit Documentation Feedback
13
LP2998, LP2998-Q1
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
www.ti.com
Application Information (continued)
180
170
160
150
SOP Board
TJA
140
130
120
110
JEDEC Board
100
90
80
0
200
400
600
800
1000
AIRFLOW (Linear Feet per Minute)
Figure 17. RθJA vs Airflow (SOIC-8)
Additional improvements can be made by the judicious use of vias to connect the part and dissipate heat to an
internal ground plane. Using larger traces and more copper on the top side of the board can also help. With
careful layout it is possible to reduce the RθJA further than the nominal values shown in Figure 17.
Layout is also extremely critical to maximize the output current with the SO PowerPAD package. By simply
placing vias under the DAP the θJA can be lowered significantly.
Additional improvements in lowering the RθJA can also be achieved with a constant airflow across the package.
Maintaining the same conditions as above and utilizing the 2x2 via array, Figure 18 shows how the RθJA varies
with airflow.
51
50
qJA (oC/W)
49
48
47
46
45
0
100
200
300
400
500
600
AIRFLOW (Linear Feet Per Minute)
Figure 18. RΘJA vs Airflow Speed (Jedec Board with 4 Vias)
Optimizing the R θJA and placing the LP2998 in a section of a board exposed to lower ambient temperature
allows the part to operate with higher power dissipation. The internal power dissipation can be calculated by
summing the three main sources of loss: output current at VTT, either sinking or sourcing, and quiescent current
at AVIN and VDDQ. During the active state (when shutdown is not held low) the total internal power dissipation
can be calculated from the following equations:
PD = PAVIN + PVDDQ + PVTT
PAVIN = IAVIN * VAVIN
PVDDQ = VVDDQ * IVDDQ = VVDDQ2 x RVDDQ
(3)
(4)
(5)
To calculate the maximum power dissipation at VTT both conditions at VTT need to be examined, sinking, and
sourcing current. Although only one equation will add into the total, VTT cannot source and sink current
simultaneously.
14
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LP2998 LP2998-Q1
LP2998, LP2998-Q1
www.ti.com
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
Application Information (continued)
PVTT = VVTT x ILOAD (Sinking) or
PVTT = ( VPVIN - VVTT) x ILOAD (Sourcing)
(6)
(7)
The power dissipation of the LP2998 can also be calculated during the shutdown state. During this condition the
output VTT will tri-state, therefore that term in the power equation will disappear as it cannot sink or source any
current (leakage is negligible). The only losses during shutdown will be the reduced quiescent current at AVIN
and the constant impedance that is seen at the VDDQ pin.
PD = PAVIN + PVDDQ
PAVIN = IAVIN x VAVIN
PVDDQ = VVDDQ * IVDDQ = VVDDQ2 x RVDDQ
(8)
(9)
(10)
9.2 Typical Application
Several different application circuits are shown below to illustrate some of the options that are possible in
configuring the LP2998. Graphs of the individual circuit performance can be found in the Typical Characteristics
section. These curves illustrate how the maximum output current is affected by changes in AVIN and PVIN.
LP2998
SD
+
VDDQ = 1.5V
VDDQ
VDD = 2.5V
AVIN
47PF
0.01PF
VSENSE
VTT
PVIN
+
VREF = 0.75V
VREF
SD
VTT = 0.75V
+
GND
220PF
Figure 19. Typical Application Circuit
9.2.1 DDR-III Applications
With the separate VDDQ pin and an internal resistor divider it is possible to use the LP2998 in applications
utilizing DDR-III memory. The output stage is connected to the 1.5 V rail and the AVIN pin can be connected to a
2.2 V to 5.5 V rail.
LP2998
+
CREF
VDDQ = 1.5V
VDDQ
AVIN = 2.2V to 5.5V
AVIN
VSENSE
PVIN
VTT
PVIN = 1.5V
+
CIN
VREF = 0.75V
VREF
SD
SD
GND
VTT = 0.75V
+
COUT
Figure 20. Recommended DDR-III Termination
If it is not desirable to use the 1.5 V - 2.5 V rail it is possible to connect the output stage to a 3.3 V rail. Care
should be taken to not exceed the maximum junction temperature as the thermal dissipation increases with lower
VTT output voltages. For this reason it is not recommended to power PVIN off a rail higher than the nominal 3.3
V. The advantage of this configuration is that it has the ability to source and sink a higher maximum continuous
current.
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LP2998 LP2998-Q1
Submit Documentation Feedback
15
LP2998, LP2998-Q1
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
www.ti.com
Typical Application (continued)
9.2.2 DDR-II Applications
With the separate VDDQ pin and an internal resistor divider it is possible to use the LP2998 in applications
utilizing DDR-II memory. Figure 21 and Figure 22 show several implementations of recommended circuits with
output curves displayed in the Typical Characteristics. Figure 21 shows the recommended circuit configuration
for DDR-II applications. The output stage is connected to the 1.8 V rail and the AVIN pin can be connected to
either a 3.3 V or 5 V rail.
LP2998
+
0.01 PF
AVIN = 2.5V
AVIN
VDDQ = 1.8V
VDDQ
VSENSE
PVIN
+
VREF = 0.9V
VREF
SD
SD
VTT = 0.9V
VTT
+
GND
47 PF
220 PF
Figure 21. Recommended DDR-II Termination
If it is not desirable to use the 1.8 V rail it is possible to connect the output stage to a 3.3 V rail. Care should be
taken to not exceed the maximum junction temperature as the thermal dissipation increases with lower VTT
output voltages. For this reason it is not recommended to power PVIN off a rail higher than the nominal 3.3 V.
The advantage of this configuration is that it has the ability to source and sink a higher maximum continuous
current.
LP2998
VDDQ = 1.8V
VREF = 0.9V
VREF
SD
SD
+
CREF
VDDQ
AVIN = 3.3V or 5.5V
AVIN
PVIN = 3.3V
VSENSE
PVIN
CIN
+
VTT = 0.9V
VTT
GND
+
COUT
Figure 22. DDR-II Termination with Higher Voltage Rails
9.2.3 SSTL-2 Applications
For the majority of applications that implement the SSTL-2 termination scheme it is recommended to connect all
the input rails to the 2.5 V rail. This provides an optimal trade-off between power dissipation and component
count and selection. An example of this circuit can be seen in Figure 23.
16
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LP2998 LP2998-Q1
LP2998, LP2998-Q1
www.ti.com
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
Typical Application (continued)
LP2998
VREF = 1.25V
VREF
SD
SD
+
VDDQ
VDDQ = 2.5V
VDD = 2.5V
CIN
+
AVIN
VSENSE
PVIN
VTT
CREF
VTT = 1.25V
+
GND
COUT
Figure 23. Recommended SSTL-2 Implementation
If power dissipation or efficiency is a major concern then the LP2998 has the ability to operate on split power
rails. The output stage (PVIN) can be operated on a lower rail such as 1.8 V and the analog circuitry (AVIN) can
be connected to a higher rail such as 2.5 V, 3.3 V, or 5 V. This allows the internal power dissipation to be
lowered when sourcing current from VTT. The disadvantage of this circuit is that the maximum continuous current
is reduced because of the lower rail voltage, although it is adequate for all motherboard SSTL-2 applications.
Increasing the output capacitance can also help if periods of large load transients will be encountered.
LP2998
VREF = 1.25V
VREF
SD
SD
+
VDDQ = 2.5V
VDDQ
AVIN = 2.2V to 5.5V
AVIN
VSENSE
PVIN
PVIN = 1.8V
CIN
CREF
VTT = 1.25V
VTT
+
+
GND
COUT
Figure 24. Lower Power Dissipation SSTL-2 Implementation
The third option for SSTL-2 applications in the situation that a 1.8 V rail is not available and it is not desirable to
use 2.5 V, is to connect the LP2998 power rail to 3.3 V. In this situation AVIN will be limited to operation on the
3.3 V or 5 V rail as PVIN can never exceed AVIN. This configuration has the ability to provide the maximum
continuous output current at the downside of higher thermal dissipation. Care should be taken to prevent the
LP2998 from experiencing large current levels which cause the junction temperature to exceed the maximum.
Because of this risk it is not recommended to supply the output stage with a voltage higher than a nominal 3.3 V
rail.
LP2998
VREF
SD
SD
VREF = 1.25V
+
VDDQ
VDDQ = 2.5V
AVIN = 3.3V or 5V
AVIN
PVIN = 3.3V
VSENSE
PVIN
CIN
+
CREF
VTT = 1.25V
VTT
GND
+
COUT
Figure 25. SSTL-2 Implementation with Higher Voltage Rails
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LP2998 LP2998-Q1
Submit Documentation Feedback
17
LP2998, LP2998-Q1
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
www.ti.com
Typical Application (continued)
9.2.4 Level Shifting
If standards other than SSTL-2 are required, such as SSTL-3, it may be necessary to use a different scaling
factor than 0.5 times VDDQ for regulating the output voltage. Several options are available to scale the output to
any voltage required. One method is to level shift the output by using feedback resistors from VTT to the VSENSE
pin. This has been illustrated in Figure 26 and Figure 27. Figure 26 shows how to use two resistors to level shift
VTT above the internal reference voltage of VDDQ/2. To calculate the exact voltage at VTT the following equation
can be used.
VTT = VDDQ/2 ( 1 + R1/R2)
(11)
LP2998
VDDQ
VDDQ
VDD
VTT
VTT
AVIN
R1
PVIN
CIN
+
VSENSE
+
GND
COUT
R2
Figure 26. Increasing VTT by Level Shifting
Conversely, the R2 resistor can be placed between VSENSE and VDDQ to shift the VTT output lower than the
internal reference voltage of VDDQ/2. The equations relating VTT and the resistors can be seen below:
VTT = VDDQ/2 (1 - R1/R2)
(12)
LP2998
VDDQ
VDDQ
VDD
R2
VSENSE
AVIN
R1
CIN
VTT
VTT
PVIN
+
+
GND
COUT
Figure 27. Decreasing VTT by Level Shifting
9.2.4.1 Output Capacitor Selection
For applications utilizing the LP2998 to terminate SSTL-2 I/O signals the typical application circuit shown in
Figure 28 can be implemented.
LP2998
AVIN = 2.5V
AVIN
VDDQ = 1.8V
VDDQ
+
+
CREF
VSENSE
PVIN
CIN
VREF = 0.9V
VREF
SD
SD
VTT = 0.9V
VTT
GND
+
COUT
Figure 28. Typical SSTL-2 Application Circuit
18
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LP2998 LP2998-Q1
LP2998, LP2998-Q1
www.ti.com
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
Typical Application (continued)
This circuit permits termination in a minimum amount of board space and component count. Capacitor selection
can be varied depending on the number of lines terminated and the maximum load transient. However, with
motherboards and other applications where VTT is distributed across a long plane it is advisable to use multiple
bulk capacitors and addition to high frequency decoupling. Figure 29 shown below depicts an example circuit
where 2 bulk output capacitors could be situated at both ends of the VTT plane for optimal placement. Large
aluminum electrolytic capacitors are used for their low ESR and low cost.
LP2998
SD
VDDQ = 2.5V
VDDQ
VDD = 2.5V
AVIN
VREF = 1.25V
VREF
SD
+
0.01 PF
VSENSE
PVIN
VTT
+
47 PF
VTT = 1.25V
+
GND
+
330 PF
330 PF
Figure 29. Typical SSTL-2 Application Circuit for Motherboards
In most PC applications an extensive amount of decoupling is required because of the long interconnects
encountered with the DDR-SDRAM DIMMs mounted on modules. As a result bulk aluminum electrolytic
capacitors in the range of 1000 µF are typically used.
9.2.5 HSTL Applications
The LP2998 can be easily adapted for HSTL applications by connecting VDDQ to the 1.5 V rail. This will produce
a VTT and VREF voltage of approximately 0.75 V for the termination resistors. AVIN and PVIN should be
connected to a 2.5 V rail for optimal performance.
LP2998
VREF
SD
SD
VREF = 0.75V
+
VDDQ
VDDQ = 1.5V
AVIN
VDD = 2.5V
VSENSE
PVIN
CIN
+
CREF
VTT = 0.75V
VTT
GND
+
COUT
Figure 30. HSTL Application
9.2.6 QDR Applications
Quad data rate (QDR) applications utilize multiple channels for improved memory performance. However, this
increase in bus lines has the effect of increasing the current levels required for termination. The recommended
approach in terminating multiple channels is to use a dedicated LP2998 for each channel. This simplifies layout
and reduces the internal power dissipation for each regulator. Separate VREF signals can be used for each DIMM
bank from the corresponding regulator with the chipset reference provided by a local resistor divider or one of the
LP2998 signals. Because VREF and VTT are expected to track and the part to part variations are minor, there
should be little difference between the reference signals of each LP2998.
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LP2998 LP2998-Q1
Submit Documentation Feedback
19
LP2998, LP2998-Q1
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
www.ti.com
10 Power Supply Recommendations
There are several recommendations for the LP2998 input power supply. An input capacitor is not required but is
recommended for improved performance during large load transients to prevent the input rail from dropping. The
input capacitor should be located as close as possible to the PVIN pin. Several recommendations exist
dependent on the application required. A typical value recommended for AL electrolytic capacitors is 50 µF.
Ceramic capacitors can also be used, a value in the range of 10 µF with X5R or better would be an ideal choice.
The input capacitance can be reduced if the LP2998 is placed close to the bulk capacitance from the output of
the 2.5 V DC-DC converter. If the two supply rails (AVIN and PVIN) are separated then the 47 uF capacitor
should be placed as close to possible to the PVIN rail. An additional 0.1 uF ceramic capacitor can be placed on
the AVIN rail to prevent excessive noise from coupling into the device.
11 Layout
11.1 Layout Guidelines
1. The input capacitor for the power rail should be placed as close as possible to the PVIN pin.
2. VSENSE should be connected to the VTT termination bus at the point where regulation is required. For
motherboard applications an ideal location would be at the center of the termination bus.
3. VDDQ can be connected remotely to the VDDQ rail input at either the DIMM or the Chipset. This provides the
most accurate point for creating the reference voltage.
4. For improved thermal performance excessive top side copper should be used to dissipate heat from the
package. Numerous vias from the ground connection to the internal ground plane will help. Additionally these
can be located underneath the package if manufacturing standards permit.
5. Care should be taken when routing the VSENSE trace to avoid noise pickup from switching I/O signals. A 0.1
µF ceramic capacitor located close to the SENSE can also be used to filter any unwanted high frequency
signal. This can be an issue especially if long SENSE traces are used.
6. VREF should be bypassed with a 0.01 µF or 0.1 µF ceramic capacitor for improved performance. This
capacitor should be located as close as possible to the VREF pin.
20
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LP2998 LP2998-Q1
LP2998, LP2998-Q1
www.ti.com
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
11.2 Layout Examples
Figure 31 and Figure 32 are layout examples for the LP2998/Q1. These examples are taken from the
LP2998EVM.
Figure 31. LP2998EVM SO PowerPAD Layout Example (Front)
Figure 32. LP2998EVM SO PowerPAD Layout Example (Back)
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LP2998 LP2998-Q1
Submit Documentation Feedback
21
LP2998, LP2998-Q1
SNVS521K – DECEMBER 2007 – REVISED AUGUST 2014
www.ti.com
12 Device and Documentation Support
12.1 Related Links
Table 1 lists quick access links. Categories include technical documents, support and community resources,
tools and software, and quick access to sample or buy.
Table 1. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
LP2998
Click here
Click here
Click here
Click here
Click here
LP2998-Q1
Click here
Click here
Click here
Click here
Click here
12.2 Trademarks
PowerPAD is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
22
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LP2998 LP2998-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
30-Jul-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LP2998MA/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LP2998
MA
LP2998MAE/NOPB
ACTIVE
SOIC
D
8
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LP2998
MA
LP2998MAX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LP2998
MA
LP2998MR/NOPB
ACTIVE SO PowerPAD
DDA
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 125
LP2998
MR
LP2998MRE/NOPB
ACTIVE SO PowerPAD
DDA
8
250
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 125
LP2998
MR
LP2998MRX/NOPB
ACTIVE SO PowerPAD
DDA
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 125
LP2998
MR
LP2998QMR/NOPB
ACTIVE SO PowerPAD
DDA
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 125
LP2998
Q1MR
LP2998QMRE/NOPB
ACTIVE SO PowerPAD
DDA
8
250
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 125
LP2998
Q1MR
LP2998QMRX/NOPB
ACTIVE SO PowerPAD
DDA
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 125
LP2998
Q1MR
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
30-Jul-2014
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LP2998, LP2998-Q1 :
• Catalog: LP2998
• Automotive: LP2998-Q1
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
13-Apr-2016
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
LP2998MAE/NOPB
SOIC
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
D
8
250
178.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LP2998MAX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LP2998MRE/NOPB
SO
Power
PAD
DDA
8
250
178.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LP2998MRX/NOPB
SO
Power
PAD
DDA
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LP2998QMRE/NOPB
SO
Power
PAD
DDA
8
250
178.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LP2998QMRX/NOPB
SO
Power
PAD
DDA
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
13-Apr-2016
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LP2998MAE/NOPB
SOIC
D
LP2998MAX/NOPB
SOIC
D
8
250
210.0
185.0
35.0
8
2500
367.0
367.0
35.0
LP2998MRE/NOPB
SO PowerPAD
DDA
LP2998MRX/NOPB
SO PowerPAD
DDA
8
250
213.0
191.0
55.0
8
2500
367.0
367.0
LP2998QMRE/NOPB
SO PowerPAD
35.0
DDA
8
250
213.0
191.0
55.0
LP2998QMRX/NOPB
SO PowerPAD
DDA
8
2500
367.0
367.0
35.0
Pack Materials-Page 2
PACKAGE OUTLINE
DDA0008A
PowerPAD TM SOIC - 1.7 mm max height
SCALE 2.400
PLASTIC SMALL OUTLINE
C
6.2
TYP
5.8
SEATING PLANE
PIN 1 ID
AREA
A
0.1 C
6X 1.27
8
1
2X
3.81
5.0
4.8
NOTE 3
4
5
B
8X
4.0
3.8
NOTE 4
0.51
0.31
0.25
1.7 MAX
C A B
0.25
TYP
0.10
SEE DETAIL A
5
4
EXPOSED
THERMAL PAD
0.25
GAGE PLANE
2.34
2.24
8
1
0 -8
0.15
0.00
1.27
0.40
DETAIL A
2.34
2.24
TYPICAL
4218825/A 05/2016
PowerPAD is a trademark of Texas Instruments.
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.
5. Reference JEDEC registration MS-012.
www.ti.com
EXAMPLE BOARD LAYOUT
DDA0008A
PowerPAD TM SOIC - 1.7 mm max height
PLASTIC SMALL OUTLINE
(2.95)
NOTE 9
SOLDER MASK
DEFINED PAD
(2.34)
SOLDER MASK
OPENING
8X (1.55)
SEE DETAILS
1
8
8X (0.6)
SYMM
(1.3)
TYP
(2.34)
SOLDER MASK
OPENING
(4.9)
NOTE 9
6X (1.27)
5
4
(R0.05) TYP
METAL COVERED
BY SOLDER MASK
SYMM
( 0.2) TYP
VIA
(1.3) TYP
(5.4)
LAND PATTERN EXAMPLE
SCALE:10X
0.07 MIN
ALL AROUND
0.07 MAX
ALL AROUND
SOLDER MASK
OPENING
METAL
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4218825/A 05/2016
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
8. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature
numbers SLMA002 (www.ti.com/lit/slma002) and SLMA004 (www.ti.com/lit/slma004).
9. Size of metal pad may vary due to creepage requirement.
10. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown
on this view. It is recommended that vias under paste be filled, plugged or tented.
www.ti.com
EXAMPLE STENCIL DESIGN
DDA0008A
PowerPAD TM SOIC - 1.7 mm max height
PLASTIC SMALL OUTLINE
(2.34)
BASED ON
0.125 THICK
STENCIL
8X (1.55)
(R0.05) TYP
1
8
8X (0.6)
(2.34)
BASED ON
0.125 THICK
STENCIL
SYMM
6X (1.27)
5
4
METAL COVERED
BY SOLDER MASK
SYMM
(5.4)
SEE TABLE FOR
DIFFERENT OPENINGS
FOR OTHER STENCIL
THICKNESSES
SOLDER PASTE EXAMPLE
EXPOSED PAD
100% PRINTED SOLDER COVERAGE BY AREA
SCALE:10X
STENCIL
THICKNESS
SOLDER STENCIL
OPENING
0.1
0.125
0.150
0.175
2.62 X 2.62
2.34 X 2.34 (SHOWN)
2.14 X 2.14
1.98 X 1.98
4218825/A 05/2016
NOTES: (continued)
11. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
12. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated
Similar pages