Intersil ISL78302ARBNZ Dual ldo with low noise, high performance and low iq Datasheet

Dual LDO with Low Noise, High Performance and Low IQ
ISL78302
Features
ISL78302 is a high performance dual LDO capable of sourcing
300mA current from each output. It has a low standby current
and is stable with output capacitance of 1µF to 10µF with ESR of
up to 200mΩ.
• Integrates Two 300mA High Performance LDOs
The device integrates an individual Power-On-Reset (POR) function for
each output. The POR delay for VO2 can be externally programmed by
connecting a timing capacitor to the CPOR pin. The POR delay for VO1 is
internally fixed at approximately 2ms. A reference bypass pin is also
provided for connecting a noise filtering capacitor for low noise and
high-PSRR applications.
The quiescent current is typically only 47µA with both LDOs
enabled and active. Separate enable pins control each individual
LDO output. When both enable pins are low, the device is in
shutdown, typically drawing less than 0.5µA.
The part operates down to 2.3V and up to 6.5V input. The typical
output voltage can be as low as 1.2V and as high as 3.3V for
each regulator. Please refer to the ordering information section
for standard options. Other voltage selections are available upon
request.
• Excellent Transient Response to Large Current Steps
• ±1.8% Accuracy Over All Operating Conditions
• Excellent Load Regulation: < 0.1% Voltage Change Across Full
Range of Load Current
• Extremely Low Quiescent Current: 47µA (Both LDOs Active)
• Wide Input Voltage Capability: 2.3V to 6.5V
• Low Dropout Voltage: Typically 300mV @ 300mA
• Low Output Noise: Typically 37µVRMS @ 100µA (1.5V)
• Stable with 1µF to 10µF Ceramic Capacitors
• Separate Enable and POR Pins for Each LDO
• Soft-start and Staged Turn-on to Limit Input Current Surge
During Enable
• Current Limit and Over-temperature Protection
• Tiny 10 Lead 3mm x 3mm DFN Package
• TS16949 Compliant
• AEC - Q100 Tested
The ISL78302 is both AEC - Q100 rated and fully TS16949
compliant. The ISL78302 is rated for the automotive
temperature range (-40°C to +105°C).
• Pb-free (RoHS Compliant)
Applications
• Radio Receivers
• Camera Modules
• GPS/Navigation
• Infotainment Systems
Typical Application
ISL78302
VIN (2.3 TO 6.5V)
1
ON
2
ENABLE1
OFF ON
ENABLE2
OFF
3
4
5
C1
C2
VIN
EN1
VO1
VO2
EN2
POR2
CBYP
POR1
CPOR
GND
10
VOUT1
9
VOUT2 OK
8
7
VOUT2 TOO LOW
VOUT1 OK
6
C3
C4
C5
VOUT1 TOO LOW
VOUT2
RESET2
(200ms DELAY,
C3 = 0.01µF)
RESET1
(2ms DELAY)
C1, C4, C5: 1µF X5R CERAMIC CAPACITOR
C2: 0.01µF X7R CERAMIC CAPACITOR
C3: 0.01µF X7R CERAMIC CAPACITOR
January 28, 2011
FN7696.0
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2011. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
ISL78302
Block Diagram
VIN
VO1
VO2
LDO
ERROR
AMPLIFIER
VO1
~1.0V
VREF
TRIM
IS1
VO2
POR
COMPARATOR
QEN1
VOK1
1V
POR1
LDO-1
POR2
QEN2
VO1
100k
QEN1
IS2
LDO-2
IS1
VOK2
EN1
CONTROL
LOGIC
EN2
POR2
POR2
DELAY
VOK2
CBYP
VO2
BANDGAP AND
TEMPERATURE
SENSOR
VOLTAGE
REFERENCE
GENERATOR
100k
UVLO
1.00V
POR1
DELAY
VOK1
0.94V
POR1
0.90V
GND
CPOR
Pin Configuration
ISL78302
(10 LD 3X3 DFN)
TOP VIEW
2
VIN 1
10 VO1
EN1 2
9
VO2
EN2 3
8
POR2
CBYP 4
7
POR1
CPOR 5
6
GND
FN7696.0
January 28, 2011
ISL78302
Pin Descriptions
PIN
NUMBER
PIN
NAME
1
VIN
Analog I/O
Supply Voltage/LDO Input. Connect a 1µF capacitor to GND.
2
EN1
Low Voltage Compatible CMOS Input
LDO-1 Enable. ENABLE = HIGH
3
EN2
Low Voltage Compatible CMOS Input
LDO-2 Enable. ENABLE = HIGH
4
CBYP
Analog I/O
Reference Bypass Capacitor Pin. Recommended to connect capacitor of value
0.01µF between this pin and GND for optimum noise and PSRR performance.
5
CPOR
Analog I/O
POR2 Delay Setting Capacitor Pin. Connect a capacitor between this pin and
GND to delay the POR2 output release after LDO-2 output reaches 94% of its
specified voltage level. (200ms delay per 0.01µF).
6
GND
Ground
GND is the connection to system ground. Connect to PCB Ground plane.
7
POR1
Open Drain Output (1mA)
Open-drain POR Output for LDO-1 (active-low). Internally connected to VO1
through 100kΩ resistor.
8
POR2
Open Drain Output (1mA)
Open-drain POR Output for LDO-2 (active-low). Internally connected to VO2
through 100kΩ resistor.
9
VO2
Analog I/O
LDO-2 Output. Connect capacitor of value 1µF to 10µF to GND (1µF
recommended).
10
VO1
Analog I/O
LDO-1 Output. Connect capacitor of value 1µF to 10µF to GND (1µF
recommended).
TYPE
DESCRIPTION
Ordering Information
PART NUMBER
(Notes 1, 3, 4)
PART
MARKING
VO1 VOLTAGE
(V) (Note 2)
VO2 VOLTAGE
(V) (Note 2)
TEMP RANGE
(°C)
PACKAGE
(Pb-Free)
PKG
DWG. #
ISL78302ARFBZ
DNAB
2.5
1.5
-40 to +105
10 Ld 3x3 DFN
L10.3x3C
Coming Soon
ISL78302ARBFZ
DNAC
1.5
2.5
-40 to +105
10 Ld 3x3 DFN
L10.3x3C
Coming Soon
ISL78302ARNBZ
DNAD
3.3
1.5
-40 to +105
10 Ld 3x3 DFN
L10.3x3C
Coming Soon
ISL78302ARBNZ
DNAE
1.5
3.3
-40 to +105
10 Ld 3x3 DFN
L10.3x3C
Coming Soon
ISL78302ARNWZ
DNAF
3.3
1.2
-40 to +105
10 Ld 3x3 DFN
L10.3x3C
Coming Soon
ISL78302ARWCZ
DNAG
1.2
1.8
-40 to +105
10 Ld 3x3 DFN
L10.3x3C
Coming Soon
ISL78302ARFWZ
DNAH
2.5
1.2
-40 to +105
10 Ld 3x3 DFN
L10.3x3C
Coming Soon
ISL78302ARCWZ
DANJ
1.8
1.2
-40 to +105
10 Ld 3x3 DFN
L10.3x3C
NOTES:
1. Add “-T*”suffix for tape and reel. Please refer to TB347 for details on reel specifications.
2. For other output voltages, contact Intersil.
3. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil
Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
4. For Moisture Sensitivity Level (MSL), please see device information page for ISL78302. For more information on MSL please see techbrief TB363.
3
FN7696.0
January 28, 2011
ISL78302
Absolute Maximum Ratings
Thermal Information
Supply Voltage (VIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+7.1V
VO1, VO2 Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +3.6V
All Other Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to (VIN + 0.3)V
Thermal Resistance (Notes 5, 6)
θJA (°C/W) θJC (°C/W)
10 Ld 3x3 DFN Package . . . . . . . . . . . . . . .
59
18.5
Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . .-40°C to +125°C
Operating Temperature Range . . . . . . . . . . . . . . . . . . . . .-40°C to +105°C
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
ESD Ratings
Human Body Model (Tested per JESD22-A114E) . . . . . . . . . . . . . . . . . . 3kV
Machine Model (Tested per JESD-A115-A) . . . . . . . . . . . . . . . . . . . . . 200V
Charge Device Model (Tested per JESD22-C101C). . . . . . . . . . . . . . . . . 2kV
Recommended Operating Conditions
Ambient Temperature Range (TA) . . . . . . . . . . . . . . . . . . .-40°C to +105°C
Supply Voltage (VIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3V to 6.5V
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
5. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379.
6. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside.
Electrical Specifications Unless otherwise noted, all parameters are guaranteed over the operational supply voltage and
temperature range of the device as follows: TA = -40°C to +105°C; VIN = (VO + 0.5V) to 6.5V with a minimum VIN of 2.3V; CIN = 1µF; CO = 1µF;
CBYP = 0.01µF; CPOR = 0.01µF. Boldface limits apply over the operating temperature range, -40°C to +105°C.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
(Note 8)
TYP
MAX
(Note 8)
UNITS
6.5
V
DC CHARACTERISTICS
Supply Voltage
VIN
2.3
Quiescent condition: IO1 = 0µA; IO2 = 0µA
Ground Current
IDD1
One LDO active
30
36
µA
IDD2
Both LDO active
47
55
µA
0.3
2.1
µA
Shutdown Current
IDDS
UVLO Threshold
VUV+
1.9
2.1
2.3
V
VUV-
1.6
1.8
2.0
V
Regulation Voltage Accuracy
Maximum Output Current
IMAX
Internal Current Limit
ILIM
Dropout Voltage (Note 7)
VDO
Thermal Shutdown Temperature
VIN = VO + 0.5V to 5.5V, IO = 10µA to 300mA,
TJ = +25°C
-0.8
+0.8
%
VIN = VO + 0.5V to 5.5V, IO = 10µA to 300mA,
TJ = -40°C to +125°C
-1.8
+1.8
%
Continuous
300
320
mA
475
IO = 300mA
300
IO = 150mA
150
650
mA
mV
250
mV
TSD+
145
°C
TSD-
110
°C
@ 1kHz
64
dB
@ 10kHz
51
dB
@ 100kHz
38
dB
AC CHARACTERISTICS
Ripple Rejection
IO = 10mA, VIN = 2.8V(min), VO = 1.5V,
CBYP = 0.01µF
4
FN7696.0
January 28, 2011
ISL78302
Electrical Specifications Unless otherwise noted, all parameters are guaranteed over the operational supply voltage and
temperature range of the device as follows: TA = -40°C to +105°C; VIN = (VO + 0.5V) to 6.5V with a minimum VIN of 2.3V; CIN = 1µF; CO = 1µF;
CBYP = 0.01µF; CPOR = 0.01µF. Boldface limits apply over the operating temperature range, -40°C to +105°C. (Continued)
PARAMETER
SYMBOL
MIN
(Note 8)
TEST CONDITIONS
IO = 100µA, VO = 1.5V, TA = +25°C, CBYP = 0.01µF
BW = 10Hz to 100kHz
Output Noise Voltage
TYP
MAX
(Note 8)
37
UNITS
µVRMS
DEVICE START-UP CHARACTERISTICS
Device Enable Time
tEN
Time from assertion of the ENx pin to when the output
voltage reaches 95% of the VO(nom)
250
500
µs
LDO Soft-Start Ramp Rate
tSSR
Slope of linear portion of LDO output voltage ramp during
start-up
30
60
µs/V
EN1, EN2 PIN CHARACTERISTICS
Input Low Voltage
VIL
-0.3
0.5
V
Input High Voltage
VIH
1.35
VIN + 0.3
V
0.1
µA
Input Leakage Current
IIL, IIH
Pin Capacitance
CPIN
Informative
5
pF
POR1, POR2 PIN CHARACTERISTICS
POR1, POR2 Thresholds
VPOR+
POR1 Delay
As a percentage of nominal output voltage
91
94
97
%
VPOR-
87
90
93
%
tP1LH
0.5
2.0
3.2
ms
25
tP1HL
POR2 Delay
tP2LH
CPOR = 0.01µF
100
VOL
POR1, POR2 Pin Internal Pull-Up
Resistance
300
25
tP2HL
POR1, POR2 Pin Output Low
Voltage
200
µs
@ IOL = 1.0mA
RPOR
78
100
ms
µs
0.2
V
180
kΩ
NOTES:
7. VOx = 0.98*VOx(NOM); Valid for VOx greater than 1.85V.
8. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design.
EN1
EN2
tEN
VPOR+
VPOR-
VPOR+
VPOR-
<tP1HL
VO1
VO2
<tP2HL
tP1LH
tP1HL
tP2LH
tP2HL
POR1
POR2
FIGURE 1. TIMING PARAMETER DEFINITION
5
FN7696.0
January 28, 2011
ISL78302
Typical Performance Curves
0.20
0.4
VO = 2.5V
ILOAD = 0mA
+25°C
0.2
-40°C
+105°C
0.1
0
-0.1
-0.2
-0.3
-0.4
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VIN = 3.3V
0.15
OUTPUT VOLTAGE CHANGE (%)
OUTPUT VOLTAGE, VO (%)
0.3
VO = 2.5V
0.10
+25°C
0
-0.05
-0.10
-0.15
-0.20
6.5
0
50
100
INPUT VOLTAGE (V)
200
250
300
400
2.6
0.08
VIN = 3.3V
VO = 2.5V
2.4
OUTPUT VOLTAGE, VO (V)
0.06
0.04
0.02
0
-0.02
-0.04
VIN = 3.3V
VO = 1.5V
-0.06
VO = 2.5V
IO = 0mA
2.2
IO = 150mA
IO = 300mA
2.0
VO = 1.5V
IO = 0mA
IO = 150mA
IO = 300 mA
1.8
1.6
-0.08
-0.10
-40
-25
-10
5
20
35
50
65
80
95
1.4
1.5
110
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
INPUT VOLTAGE (V)
TEMPERATURE (°C)
FIGURE 5. OUTPUT VOLTAGE vs INPUT VOLTAGE (2.5V and 1.5V
OUTPUT)
FIGURE 4. OUTPUT VOLTAGE CHANGE vs TEMPERATURE
55
400
+105°C
VO = 1.5V
+25°C
300
54
-40°C
53
GROUND CURRENT (µA)
350
250
200
150
100
50
0
350
FIGURE 3. LOAD REGULATION
0.10
OUTPUT VOLTAGE CHANGE (%)
150
LOAD CURRENT - IO (mA)
FIGURE 2. LINE REGULATION (2.5V OUTPUT)
DROPOUT VOLTAGE, VDO (mV)
+105°C
-40°C
0.05
+105°C
+25°C
52
-40°C
51
50
49
48
VO1 = 2.5V
VO2= 1.5V
IO (BOTH CHANNELS) = 0µA
47
46
0
50
100
150
200
250
300
350
OUTPUT LOAD (mA)
FIGURE 6. DROPOUT VOLTAGE vs LOAD CURRENT
6
400
45
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
INPUT VOLTAGE (V)
FIGURE 7. GROUND CURRENT vs INPUT VOLTAGE
FN7696.0
January 28, 2011
ISL78302
Typical Performance Curves
(Continued)
200
60
VIN = 3.6V
VO1= 2.5V
VO1= 2.5V
+105°C
VO2= 1.5V
160
GROUND CURRENT (µA)
GROUND CURRENT (µA)
180
VIN = 3.5V
140
120
100
80
-40°C
VO2= 1.5V
55
ILOAD = 0µA
BOTH OUTPUTS ON
50
45
60
+25°C
40
0
50
100
150
200
250
LOAD CURRENT (mA)
300
350
FIGURE 8. GROUND CURRENT vs LOAD
400
40
-40
-25
-10
80
95
110
VO1 = 2.5V
VO2 = 1.5V
IL1 = 300mA
POR1
IL2 = 300mA
VO1
VO1
20
35
50
65
TEMPERATURE (°C)
FIGURE 9. GROUND CURRENT vs TEMPERATURE
VO1 = 2.5V
VO2 = 1.5V
IL1 = 300mA
VIN
5
VO2
IL2 = 300mA
CPOR = 0.01µF
POR2
V02
FIGURE 10. POWER-UP/POWER-DOWN
VO2 (10mV/DIV)
FIGURE 11. POWER-UP/POWER-DOWN WITH POR SIGNALS
VO (50mV/DIV)
VIN = 3.5V
VO = 1.5V
VO1 = 2.5V
VO2 = 1.5V
IL1, IL2 = 300mA
CBYP = 0.01uF
CL1, CL2 = 1µF
ILOAD
FIGURE 12. TURN-ON/TURN-OFF RESPONSE
7
FIGURE 13. LOAD TRANSIENT RESPONSE
FN7696.0
January 28, 2011
ISL78302
Typical Performance Curves
(Continued)
100
10
90
VOUT = 1.5V
80
IO = 10mA
CLOAD = 1µF
70
PSRR (dB)
SPECTRAL NOISE DENSITY (mV/√Hz)
VIN = 3.3V
CBYP = 0.01µF
60
50
40
30
20
10
0
10
100
1k
10k
100k
VIN = 3.6V
VOUT = 2.5V
ILOAD = 10mA
CIN = 1µF
1
CLOAD = 1µF
CBYP = 0.01µF
0.1
0.01
10
1M
100
1k
FIGURE 14. PSRR vs FREQUENCY
1M
10
VIN = 3.6V
SPECTRAL NOISE DENSITY (mV/√Hz)
SPECTRAL NOISE DENSITY (mV/√Hz)
100k
FIGURE 15. SPECTRAL NOISE DENSITY vs FREQUENCY (2.5V
OUTPUT, 10mA LOAD)
10
VOUT = 2.5V
ILOAD = 300mA
CIN = 1µF
1
CLOAD = 1µF
CBYP = 0.01µF
0.1
0.01
10
10k
FREQUENCY (Hz)
FREQUENCY (Hz)
100
1k
10k
100k
VIN = 3.6V
VOUT = 1.5V
ILOAD = 10mA
CIN = 1µF
1
CLOAD = 1µF
CBYP = 0.01µF
0.1
0.01
10
1M
100
1k
10k
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 16. SPECTRAL NOISE DENSITY vs FREQUENCY (2.5V
OUTPUT, 300mA LOAD)
100k
1M
FIGURE 17. SPECTRAL NOISE DENSITY vs FREQUENCY (1.5V
OUTPUT, 10mA LOAD)
SPECTRAL NOISE DENSITY (mV/√Hz)
10
VIN = 3.6V
VOUT = 1.5V
ILOAD = 300mA
CIN = 1µF
1
COUT = 1µF
CBYP = 0.01µF
0.1
0.01
10
100
1k
10k
100k
1M
FREQUENCY (Hz)
FIGURE 18. SPECTRAL NOISE DENSITY vs FREQUENCY (1.5V OUTPUT, 300mA LOAD)
8
FN7696.0
January 28, 2011
ISL78302
Functional Description
The ISL78302 contains two high performance LDOs. High
performance is achieved through a circuit that delivers fast
transient response to varying load conditions. In a quiescent
condition, the ISL78302 adjusts its biasing to achieve the lowest
standby current consumption.
The device also integrates current limit protection, smart thermal
shutdown protection, staged turn-on and soft-start. Smart
thermal shutdown protects the device against overheating.
Staged turn-on and soft-start minimize start-up input current
surges without causing excessive device turn-on time.
Power Control
The ISL78302 has two separate enable pins (EN1 and EN2) to
individually control power to each of the LDO outputs. When both
EN1 and EN2 are low, the device is in shutdown mode. During
this condition, all on-chip circuits are off, and the device draws
minimum current, typically less than 0.5µA.
When one or both of the enable pins is asserted, the device first
polls the output of the UVLO detector to ensure that VIN voltage is
at least about 2.1V. Once verified, the device initiates a start-up
sequence. During the start-up sequence, trim settings are first
read and latched. Then, sequentially, the bandgap, reference
voltage and current generation circuitry power-up. Once the
references are stable, a fast-start circuit quickly charges the
external reference bypass capacitor (connected to the CBYP pin)
to the proper operating voltage. After the bypass capacitor has
been charged, the LDOs power-up in their specified sequence.
Soft-start circuitry integrated into each LDO limits the initial
ramp-up rate to about 30µs/V to minimize current surge.
If EN1 is brought high and EN2 goes high before the VO1 output
stabilizes, the ISL78302 delays the VO2 turn-on until the VO1
output reaches its target level.
If EN2 is brought high and EN1 goes high before VO2 starts its
output ramp, then VO1 turns on first and, the ISL78302 delays
the VO2 turn-on until the VO1 output reaches its target level.
If EN2 is brought high and EN1 goes high after VO2 starts its
output ramp, then the ISL78302 immediately starts to ramp up
the VO1 output.
If both EN1 and EN2 are brought high at the same time, the VO1
output has priority and is always powered up first.
During operation, whenever the VIN voltage drops below 1.8V,
the ISL78302 immediately disables both LDO outputs. When VIN
rises back above 2.1V, the device re-initiates its start-up
sequence, and LDO operation will resume automatically.
Reference Generation
The reference generation circuitry includes a trimmed bandgap,
a trimmed voltage reference divider, a trimmed current reference
generator, and an RC noise filter. The filter includes the external
capacitor connected to the CBYP pin. A 0.01µF (capacitor
connected CBYP) implements a 100Hz lowpass filter and is
recommended for most high-performance applications.
Capacitor values above 0.01µF are not recommended for the
CBYP pin.
9
The bandgap generates a zero temperature coefficient (TC)
voltage for the reference divider. The reference divider provides
the regulation reference, POR detection thresholds, and other
voltage references required for current generation and
over-temperature detection.
The current generator provides the references required for
adaptive biasing as well as references for LDO output current
limit and thermal shutdown determination.
LDO Regulation and Programmable Output
Divider
The LDO regulator is implemented with a high-gain operational
amplifier driving a PMOS pass transistor. The design of the
ISL78302 provides a regulator that has low quiescent current, fast
transient response, and overall stability across all operating and
load current conditions. LDO stability is guaranteed for a 1µF to
10µF output capacitor that has a tolerance better than 20% and an
ESR less than 200mΩ. The design is performance-optimized for a
1µF capacitor. Unless limited by the application, use of an output
capacitor value above 4.7µF is not normally needed, as LDO
performance improvement is minimal.
Each LDO uses an independently trimmed 1V reference. An
internal resistor divider drops the LDO output voltage down to 1V.
This is compared to the 1V reference for regulation. The resistor
division ratio is programmed in the factory to the output voltages
of 1.2V, 1.5V, 1.8V, 2.5V and 3.3V.
Power-On Reset Generation
Each LDO has a separate Power-on Reset signal generation
circuit, which outputs to the respective POR pins. The POR signal
is generated as follows.
A POR comparator continuously monitors the output of each
LDO. The LDO enters a power-good state when the output voltage
is above 94% of the expected output voltage for a period
exceeding the LDO PGOOD entry delay time. In the power-good
state, the open-drain PORx output is in a high-impedance state.
An internal 100kΩ pull-up resistor pulls the pin up to the
respective LDO output voltage. An external resistor can be added
between the PORx output and the LDO output for a faster rise
time; however, the PORx output should not connect through an
external resistor to a supply greater than the associated LDO
voltage.
The power-good state is exited when the LDO output falls below
90% of the expected output voltage for a period longer than the
PGOOD exit delay time. While power-good is false, the ISL78302
pulls the respective POR pin low.
For LDO-1, the PGOOD entry delay time is fixed at about 2ms,
while the PGOOD exit delay is about 25µs. For LDO-2, the PGOOD
entry and exit delays are determined by the value of the external
capacitor connected to the CPOR pin. For a 0.01µF capacitor, the
entry and exit delays are 200ms and 25µs, respectively. Larger
or smaller capacitor values will yield proportionately longer or
shorter delay times. The POR exit delay should never be allowed
to be less than 10µs to ensure sufficient immunity against
transient induced false POR triggering.
FN7696.0
January 28, 2011
ISL78302
Over-Temperature Detection
The bandgap provides a proportional-to-temperature current that
indicates the temperature of the silicon. This current is compared
with references to determine whether the device is in danger of
damage from overheating. When the die temperature reaches
about +145°C, one or both of the LDOs momentarily shuts down
until the die cools sufficiently. In the overheat condition, only the
LDO sourcing more than 50mA is shut off. This shutoff does not
affect the operation of the other LDO. If both LDOs source more
than 50mA and an overheat condition occurs, both LDO outputs
are disabled. Once the die temperature falls back below about
+110°C and disabled LDOs are re-enabled, the soft-start
automatically takes place.
The ISL78302 provides short-circuit protection by limiting the
output current to about 475mA. If short circuited, an output
current of 475mA causes die heating. If the short circuit lasts
long enough, the overheat detection circuit turns off the output.
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make
sure you have the latest revision.
DATE
REVISION
1/28/11
FN7696.0
CHANGE
Initial Release.
Products
Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The Company's products
address some of the industry's fastest growing markets, such as, flat panel displays, cell phones, handheld products, and notebooks.
Intersil's product families address power management and analog signal processing functions. Go to www.intersil.com/products for a
complete list of Intersil product families.
*For a complete listing of Applications, Related Documentation and Related Parts, please see the respective device information page
on intersil.com: ISL78302
To report errors or suggestions for this datasheet, please go to: www.intersil.com/askourstaff
FITs are available from our website at: http://rel.intersil.com/reports/sear
For additional products, see www.intersil.com/product_tree
Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted
in the quality certifications found at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time
without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be
accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third
parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
10
FN7696.0
January 28, 2011
ISL78302
Package Outline Drawing
L10.3x3C
10 LEAD DUAL FLAT PACKAGE (DFN)
Rev 2, 09/09
3.00
6
PIN #1 INDEX AREA
A
B
10
6
PIN 1
INDEX AREA
1
2.38
3.00
0.50
2
10 x 0.25
6
(4X)
0.10 C B
1.64
TOP VIEW
10x 0.40
BOTTOM VIEW
5
(4X)
PACKAGE
OUTLINE
0.10 M C B
SEE DETAIL "X"
(10 x 0.60)
(10x 0.25)
0.90
MAX
0.10 C
BASE PLANE
2.38
0.20
C
SEATING PLANE
0.08 C
SIDE VIEW
(8x 0.50)
1.64
TYPICAL RECOMMENDED LAND PATTERN
C
0.20 REF
5
0.05
DETAIL "X"
NOTES:
1.
Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2.
Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3.
Unless otherwise specified, tolerance : Decimal ± 0.05
4.
Dimension b applies to the metallized terminal and is measured
between 0.18mm and 0.30mm from the terminal tip.
5.
Tiebar shown (if present) is a non-functional feature.
6.
The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 indentifier may be
either a mold or mark feature.
7. COMPLAINT TO JEDEC MO-229-WEED-3 except for E-PAD
dimensions.
11
FN7696.0
January 28, 2011
Similar pages