TI1 LF411MWGRLQMLV Lf411qml low offset, low drift jfet input operational amplifier Datasheet

LF411QML
LF411QML Low Offset, Low Drift JFET Input Operational Amplifier
Literature Number: SNOSAO6B
LF411QML
Low Offset, Low Drift JFET Input Operational Amplifier
General Description
Features
This device is a low cost, high speed, JFET input operational
amplifier with very low input offset voltage and guaranteed
input offset voltage drift. It requires low supply current yet
maintains a large gain bandwidth product and fast slew rate.
In addition, well matched high voltage JFET input devices
provide very low input bias and offset currents. The
LF411QML is pin compatible with the standard LM741 allowing designers to immediately upgrade the overall performance of existing designs.
This amplifier may be used in applications such as high speed
integrators, fast D/A converters, sample and hold circuits and
many other circuits requiring low input offset voltage and drift,
low input bias current, high input impedance, high slew rate
and wide bandwidth.
■ Available with radiation guarantee
— ELDRS FREE
Internally trimmed offset voltage:
Input offset voltage drift:
Low input bias current:
Low input noise current:
Wide gain bandwidth:
High slew rate:
Low supply current:
High input impedance:
Low total harmonic distortion:
AV = 10, RL = 10KΩ,
VO = 20VP-P, BW = 20Hz - 20KHz
■ Low 1/f noise corner:
■ Fast settling time to 0.01%:
100 krad(Si)
0.5 mV(Typ)
10 μV/°C
50 pA
0.01 pA/√Hz
3 MHz
10V/μs
1.8 mA
1012Ω
<0.0
2%
■
■
■
■
■
■
■
■
■
50 Hz
2 μs
Ordering Information
NS Part Number
SMD Part Number
LF411MH/883
NS Package Number
H08C
Package Description
8LD T0–99 Can
LF411MWG/883
WG10A
10LD Ceramic SOIC
LF411MWG-MLS
50 krad(Si)
(Note 9)
WG10A
10LD Ceramic SOIC
WG10A
10LD Ceramic SOIC
LF411MWGRLQMLV
100 krad(Si)
(Note 10)
5962R1122201VZA
ELDRS Free
Connection Diagrams
Metal Can Package
10LD Ceramic SOIC Package
20149244
Top View
See NS Package Number WG10A
20149205
Note: Pin 4 connected to case.
Top View
See NS Package Number H08A
BI-FET II™ is a trademark of National Semiconductor Corporation.
© 2011 National Semiconductor Corporation
201492
www.national.com
LF411QML Low Offset, Low Drift JFET Input Operational Amplifier
June 30, 2011
LF411QML
Simplified Schematic
20149206
Detailed Schematic
20149234
www.national.com
2
LF411QML
Absolute Maximum Ratings (Note 1)
Supply Voltage
Differential Input Voltage
Input Voltage Range (Note 4)
Output Short Circuit Duration
Power Dissipation (Note 2), (Note 3)
H Package
WG Package
TJmax
H Package
WG Package
Thermal Resistance
±18V
±30V
±15V
Continuous
670mW
670mW
150°C
150°C
θJA
H Package Still Air
H Package 500LF/Min Air Flow
WG Package Still Air
WG Package 500LF/Min Air Flow
162°C/W
65°C/W
170°C/W
120°C/W
θJC
H Package
WG Package
Operating Temperature Range
20°C/W
26°C/W
−55°C ≤ TA ≤ 125°C
−65°C ≤ TA ≤ 150°C
260°C
Storage Temperature Range
Lead Temperature (Soldering, 10 seconds)
Package Weight (Typical)
H Package
WG Package
ESD Tolerance (Note 5)
TBD
220mg
750V
Quality Conformance Inspection
Mil-Std-883, Method 5005 - Group A
Subgroup
Description
1
Static tests at
Temp °C
+25
2
Static tests at
+125
3
Static tests at
-55
4
Dynamic tests at
+25
5
Dynamic tests at
+125
6
Dynamic tests at
-55
7
Functional tests at
+25
8A
Functional tests at
+125
8B
Functional tests at
-55
9
Switching tests at
+25
10
Switching tests at
+125
11
Switching tests at
-55
12
Settling time at
+25
13
Settling time at
+125
14
Settling time at
-55
3
www.national.com
LF411QML
LF411 883 Electrical Characteristics
DC Parameters
The following conditions apply, unless otherwise specified.
DC:
VCC = ±15V, VCM = 0V, RS = 0Ω
Symbol
VIO
IIO
Parameter
Input Offset Voltage
Conditions
Notes
RS = 10KΩ
Input Offset Current
(Note 8)
±IIB
Input Bias Current
Min
Max
Unit
Subgroups
-2.0
2.0
mV
1
-3.7
3.7
mV
2
-3.3
3.3
mV
3
-0.1
0.1
nA
1
-25
25
nA
2
1
-0.2
0.2
nA
(Note 8)
-50
50
nA
2
(Note 6)
±9.0
V
1, 2, 3
VCM
Input Common Mode Voltage
Range
CMRR
Common Mode Rejection Ratio
RS ≤ 10KΩ, VCM = ±9V
70
dB
1, 2, 3
+PSRR
Supply Voltage Rejection Ratio
+VCC = 6V, -VCC = -15V
70
dB
1, 2, 3
-PSRR
Supply Voltage Rejection Ratio
+VCC = 15V, -VCC = -6V
70
IS
Supply Current
-IOS
Output Short Circuit Current
+IOS
Output Short Circuit Current
+VIO Adj
Input Offset Voltage Adjustment
-VIO Adj
Input Offset Voltage Adjustment
+AVS
Large Signal Voltage Gain
-AVS
Large Signal Voltage Gain
VO+
Output Voltage Swing
VO-
Output Voltage Swing
dB
1, 2, 3
3.4
mA
1, 2, 3
+VI = -11V, -VI = 11V,
13
50
mA
1
RS = 10KΩ
6.0
60
mA
2, 3
+VI = 11V, -VI = -11V,
-50
-13
mA
1
RS = 10KΩ
-60
-6.0
mA
2, 3
mV
1
8.0
mV
1
VO = 0 to 10V, RL = 2KΩ
(Note 7)
25
-8.0
V/mV
4
VO = 0 to 10V, RL = 2KΩ
(Note 7)
15
V/mV
5, 6
VO = 0 to -10V, RL = 2KΩ
(Note 7)
25
V/mV
4
VO = 0 to -10V, RL = 2KΩ
(Note 7)
15
V/mV
5, 6
12
V
4, 5, 6
-12
V
4, 5, 6
Max
Unit
Subgroups
RL = 10KΩ, +VI = 11V,
-VI = -11V, RS = 10KΩ
RL = 10KΩ, +VI = -11V,
-VI = 11V, RS = 10KΩ
AC Parameters
The following conditions apply, unless otherwise specified.
AC: VCC = ±15V, VCM = 0V, RS = 0Ω
Symbol
Parameter
Conditions
Notes
Min
SR+
Slew Rate
VO = -5V to 5V
8.0
V/µS
7
SR-
Slew Rate
VO = 5V to -5V
8.0
V/µS
7
GBW
Gain Bandwidth Product
2.7
MHz
7
www.national.com
4
LF411QML
Space Level Electrical Characteristics
DC Parameters
The following conditions apply, unless otherwise specified.
DC:
VCC = ±15V, VCM = 0V, RS = 0Ω
Symbol
VIO
IIO
Parameter
Input Offset Voltage
Conditions
Notes
RS = 10KΩ
Input Offset Current
(Note 8)
±IIB
Input Bias Current
Min
Max
Unit
Subgroups
-2.0
2.0
mV
1
-3.7
3.7
mV
2
-3.3
3.3
mV
3
-0.1
0.1
nA
1
-25
25
nA
2
1
-0.2
0.2
nA
(Note 8)
-50
50
nA
2
(Note 6)
±9.0
V
1, 2, 3
VCM
Input Common Mode Voltage
Range
CMRR
Common Mode Rejection Ratio
RS ≤ 10KΩ, VCM = ±9V
70
dB
1, 2, 3
+PSRR
Supply Voltage Rejection Ratio
+VCC = 6V, -VCC = -15V
70
dB
1, 2, 3
-PSRR
Supply Voltage Rejection Ratio
+VCC = 15V, -VCC = -6V
70
IS
Supply Current
-IOS
Output Short Circuit Current
+IOS
Output Short Circuit Current
+VIO Adj
Input Offset Voltage Adjustment
-VIO Adj
Input Offset Voltage Adjustment
+AVS
Large Signal Voltage Gain
-AVS
Large Signal Voltage Gain
VO+
Output Voltage Swing
VO-
Output Voltage Swing
dB
1, 2, 3
3.4
mA
1, 2, 3
+VI = -11V, -VI = 11V,
13
50
mA
1
RS = 10KΩ
6.0
60
mA
2, 3
+VI = 11V, -VI = -11V,
-50
-13
mA
1
RS = 10KΩ
-60
-6.0
mA
2, 3
mV
1
8.0
mV
1
VO = 0 to 10V, RL = 2KΩ
(Note 7)
25
-8.0
V/mV
4
VO = 0 to 10V, RL = 2KΩ
(Note 7)
15
V/mV
5, 6
VO = 0 to -10V, RL = 2KΩ
(Note 7)
25
V/mV
4
VO = 0 to -10V, RL = 2KΩ
(Note 7)
15
V/mV
5, 6
12
V
4, 5, 6
-12
V
4, 5, 6
Max
Unit
Subgroups
RL = 10KΩ, +VI = 11V,
-VI = -11V, RS = 10KΩ
RL = 10KΩ, +VI = -11V,
-VI = 11V, RS = 10KΩ
AC Parameters
The following conditions apply, unless otherwise specified.
AC: VCC = ±15V, VCM = 0V, RS = 0Ω
Symbol
Parameter
Conditions
Notes
Min
SR+
Slew Rate
VO = -5V to 5V
8.0
V/µS
7
SR-
Slew Rate
VO = 5V to -5V
8.0
V/µS
7
GBW
Gain Bandwidth Product
2.7
MHz
7
5
www.national.com
LF411QML
Space Level Electrical Characteristics (Continued)
DC Parameters - Drift Values
The following conditions apply, unless otherwise specified.
DC: VCC = ±15V, VCM = 0V, RS = 0Ω “Delta calculations performed on Space Level devices at Group B Subgroup 5 ONLY”
Symbol
Parameter
Conditions
Notes
Min
Max
Unit
Subgroups
−1
1
mV
1
VIO
Input Offset Voltage
+IIB
Input Bias Current
−0.1
0.1
nA
1
−IIB
Input Bias Current
−0.1
0.1
nA
1
Min
Max
Unit
Subgroups
LF411–MLS 50k Radiation Electrical Characteristics
DC Parameters - Post Radiation Limits (Note 9)
The following conditions apply, unless otherwise specified.
DC: VCC = ±15V, VCM = 0V, RS = 0Ω Post Radiation Limits +25°C
Symbol
Parameter
Conditions
Notes
IIO
Input Offset Current
−0.25 0.25
nA
1
IIB+
Input Bias Current
−1.0
1.0
nA
1
IIB-
Input Bias Current
−1.0
1.0
nA
1
LF411MWGRLQMLV 100k Radiation Electrical Characteristics —
ELDRS Free Only SMD# 5962R1122201
DC Parameters - Post Radiation Limits (Note 10)
The following conditions apply, unless otherwise specified.
DC: VCC = ±15V, VCM = 0V, RS = 0Ω Post Radiation Limits +25°C
Symbol
Parameter
Conditions
Notes
Min
Max
Unit
Subgroups
IIO
Input Offset Current
−1.0
1.0
nA
1
IIB+
Input Bias Current
−0.20
6.0
nA
1
IIB-
Input Bias Current
−0.20
6.0
nA
1
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed
specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test
conditions.
Note 2: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax (maximum junction temperature), θJA (package
junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is PDmax = (TJmax - TA)/
θJA or the number given in the Absolute Maximum Ratings, whichever is lower.
Note 3: Max. Power Dissipation is defined by the package characteristics. Operating the part near the Max. Power Dissipation may cause the part to operate
outside guaranteed limits.
Note 4: Unless otherwise specified the absolute maximum negative input voltage is equal to the negative power supply voltage.
Note 5: Human body model, 100pF discharged through 1.5KΩ.
Note 6: Parameters guaranteed by CMRR test.
Note 7: Datalog in K = V/mV.
Note 8: RS = 10KΩ @ +125°C.
Note 9: Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics except as listed in the Post Radiation Limits Table.
These parts may be dose rate sensitive in a space environment and demonstrate enhanced low dose rate effect. Radiation end point limits for the noted parameters
are guaranteed only for the conditions as specified in MIL-STD-883, Method 1019
Note 10: Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics except as listed in the Post Radiation Limits Table.
These parts may be sensitive in a high dose rate environment. Low dose rate testing has been performed on a wafer-by-wafer basis, per Test Method 1019,
Condition D of MIL-STD-883, with no enhanced low dose rate sensitivity (ELDRS).
www.national.com
6
LF411QML
Typical Connection
20149201
Typical Performance Characteristics
Input Bias Current
Input Bias Current
20149211
20149212
Supply Current
Positive Common-Mode
Input Voltage Limit
20149213
20149214
7
www.national.com
LF411QML
Negative Common-Mode
Input Voltage Limit
Positive Current Limit
20149216
20149215
Negative Current Limit
Output Voltage Swing
20149217
20149218
Output Voltage Swing
Gain Bandwidth
20149219
www.national.com
20149220
8
LF411QML
Bode Plot
Slew Rate
20149222
20149221
Distortion vs Frequency
Undistorted Output
Voltage Swing
20149223
20149224
Open Loop Frequency
Response
Common-Mode Rejection
Ratio
20149225
20149226
9
www.national.com
LF411QML
Power Supply
Rejection Ratio
Equivalent Input Noise
Voltage
20149227
20149228
Open Loop Voltage Gain
Output Impedance
20149229
20149230
Inverter Settling Time
20149231
www.national.com
10
LF411QML
Pulse Response
RL=2 kΩ, CL10 pF
Small Signal Inverting
Small Signal Non-Inverting
20149240
20149239
Large Signal Inverting
Large Signal Non-Inverting
20149241
20149242
Current Limit (RL=100Ω)
20149243
11
www.national.com
LF411QML
The LF411QML will drive a 2 kΩ load resistance to ±10V over
the full temperature range. If the amplifier is forced to drive
heavier load currents, however, an increase in input offset
voltage may occur on the negative voltage swing and finally
reach an active current limit on both positive and negative
swings.
Precautions should be taken to ensure that the power supply
for the integrated circuit never becomes reversed in polarity
or that the unit is not inadvertently installed backwards in a
socket as an unlimited current surge through the resulting
forward diode within the IC could cause fusing of the internal
conductors and result in a destroyed unit.
As with most amplifiers, care should be taken with lead dress,
component placement and supply decoupling in order to ensure stability. For example, resistors from the output to an
input should be placed with the body close to the input to
minimize “pick-up” and maximize the frequency of the feedback pole by minimizing the capacitance from the input to
ground.
A feedback pole is created when the feedback around any
amplifier is resistive. The parallel resistance and capacitance
from the input of the device (usually the inverting input) to AC
ground set the frequency of the pole. In many instances the
frequency of this pole is much greater than the expected
3 dB frequency of the closed loop gain and consequently
there is negligible effect on stability margin. However, if the
feedback pole is less than approximately 6 times the expected
3 dB frequency, a lead capacitor should be placed from the
output to the input of the op amp. The value of the added
capacitor should be such that the RC time constant of this
capacitor and the resistance it parallels is greater than or
equal to the original feedback pole time constant.
Application Hints
The LF411QML series of internally trimmed JFET input op
amps ( BI-FET II™ ) provide very low input offset voltage and
guaranteed input offset voltage drift. These JFETs have large
reverse breakdown voltages from gate to source and drain
eliminating the need for clamps across the inputs. Therefore,
large differential input voltages can easily be accommodated
without a large increase in input current. The maximum differential input voltage is independent of the supply voltages.
However, neither of the input voltages should be allowed to
exceed the negative supply as this will cause large currents
to flow which can result in a destroyed unit.
Exceeding the negative common-mode limit on either input
will force the output to a high state, potentially causing a reversal of phase to the output. Exceeding the negative common-mode limit on both inputs will force the amplifier output
to a high state. In neither case does a latch occur since raising
the input back within the common-mode range again puts the
input stage and thus the amplifier in a normal operating mode.
Exceeding the positive common-mode limit on a single input
will not change the phase of the output; however, if both inputs
exceed the limit, the output of the amplifier may be forced to
a high state.
The amplifier will operate with a common-mode input voltage
equal to the positive supply; however, the gain bandwidth and
slew rate may be decreased in this condition. When the negative common-mode voltage swings to within 3V of the negative supply, an increase in input offset voltage may occur.
The LF411QML is biased by a zener reference which allows
normal circuit operation on ±4.5V power supplies. Supply
voltages less than these may result in lower gain bandwidth
and slew rate.
www.national.com
12
LF411QML
Typical Applications
High Speed Current Booster
20149209
PNP=2N2905
NPN=2N2219 unless noted
TO-5 heat sinks for Q6-Q7
13
www.national.com
LF411QML
10-Bit Linear DAC with No VOS Adjust
20149232
where AN=1 if the AN digital input is high
AN=0 if the AN digital input is low
Single Supply Analog Switch with Buffered Output
20149233
www.national.com
14
Date Released Revision
10/11/05
Section
Originator
L. Lytle
Changes
A
New Release to corporate format
05/07/07
B
Features, Ordering Information Table, L. McGee
LF411-MLS Electricals
Added reference to Radiation and Radiation
Electricals for LF411-MLS device. Revision A
will be archived.
06/30/11
C
Features, Ordering Information Table, L. McGee &
LF411-MLS 50k Post Radiation
K.Kruckmeyer
Electricals, LF411MWGRLQMLV Post
Radiation Electricals
Added LF411MWGRLQMLV to Ordering Info
and modified Radiation Electricals to
“Radiation” devices. Added 50k and 100k Post
Radiation DC parameter tables. Revision B will
be archived.
15
1 MDS data sheet was converted into the
corporate data sheet format. MDS
MNLF411M-X Rev 2A2 will be archived.
www.national.com
LF411QML
Revision History
LF411QML
Physical Dimensions inches (millimeters) unless otherwise noted
Metal Can Package (H)
NS Package Number H08C
10 Lead Ceramic SOIC (WG))
NS Package Number WG10A
www.national.com
16
LF411QML
Notes
17
www.national.com
LF411QML Low Offset, Low Drift JFET Input Operational Amplifier
Notes
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
www.national.com
Products
Design Support
Amplifiers
www.national.com/amplifiers
WEBENCH® Tools
www.national.com/webench
Audio
www.national.com/audio
App Notes
www.national.com/appnotes
Clock and Timing
www.national.com/timing
Reference Designs
www.national.com/refdesigns
Data Converters
www.national.com/adc
Samples
www.national.com/samples
Interface
www.national.com/interface
Eval Boards
www.national.com/evalboards
LVDS
www.national.com/lvds
Packaging
www.national.com/packaging
Power Management
www.national.com/power
Green Compliance
www.national.com/quality/green
Switching Regulators
www.national.com/switchers
Distributors
www.national.com/contacts
LDOs
www.national.com/ldo
Quality and Reliability
www.national.com/quality
LED Lighting
www.national.com/led
Feedback/Support
www.national.com/feedback
Voltage References
www.national.com/vref
Design Made Easy
www.national.com/easy
www.national.com/powerwise
Applications & Markets
www.national.com/solutions
Mil/Aero
www.national.com/milaero
PowerWise® Solutions
Serial Digital Interface (SDI) www.national.com/sdi
Temperature Sensors
www.national.com/tempsensors SolarMagic™
www.national.com/solarmagic
PLL/VCO
www.national.com/wireless
www.national.com/training
PowerWise® Design
University
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2011 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Technical
Support Center
Email: [email protected]
Tel: 1-800-272-9959
www.national.com
National Semiconductor Europe
Technical Support Center
Email: [email protected]
National Semiconductor Asia
Pacific Technical Support Center
Email: [email protected]
National Semiconductor Japan
Technical Support Center
Email: [email protected]
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and Automotive www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
www.ti.com/video
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
Similar pages