NPC APXJ160ARA271MF80G Conductive polymer aluminum solid capacitor Datasheet

CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
PXJ
TM
NPCAP
-
New!
Series
・Super low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte.
・Rated voltage range : 2.5 to 25Vdc, Capacitance range : 82 to 820µF
・Case size range :φ6.3×7.7L
・Suitable for DC-DC converters, voltage regulators and decoupling applications used on
computer motherboards etc.
・Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
・RoHS Compliant
・Halogen Free
PXJ
Downsizing
PXG P32
◆SPECIFICATIONS
Items
Characteristics
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
-55 to +105℃
2.5 to 25Vdc
±20% (M)
Rated voltage×1.15
Shall not exceed values shown in STANDARD RATINGS.
(at 20℃, 120Hz)
(at 105℃)
(at 20℃ after 2 minutes)
0.12 max.
(at 20℃, 120Hz)
Z(-25℃)/Z(+20℃)≦1.15
Z(-55℃)/Z(+20℃)≦1.25
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 15,000 hours
at 105℃.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to the DC rated voltage at
60℃, 90 to 95% RH for 1,000 hours.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105℃)
Bias Humidity
Surge Voltage
Failure Rate
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
◆DIMENSIONS [mm]
●Terminal
Code : A
EX) 2.5V820µF
W
P
0.3max.
L±0.3
Size Code
F80
C±0.2
B±0.2
φD±0.5
◆MARKING
φD
6.3
L
7.7
A
6.6
B
6.6
C
7.2
W
0.5 to 0.8
P
1.9
J57A
820
2.5V
A±0.2
◆PART NUMBERING SYSTEM
1
2
3
4
A PXJ
5
6
7
8
9
10
A RA
11
12
13
14
15
16
17
18
M F 8 0 G
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 82µF:820, 390µF:391)
Taping code
Terminal code
Voltage code (ex. 2.5V:2R5, 10V:100)
Series code
Category
Please refer to "Product code guide (conductive polymer type)"
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
30
CAT. No. E1001P
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
TM
NPCAP
PXJSeries
New!
-
◆STANDARD RATINGS
WV
(Vdc)
2.5
6.3
10
16
20
25
Cap
(µF)
820
560
390
270
150
82
Size
code
Leakage current
(µA max./after 2min.)
F80
F80
F80
F80
F80
F80
1,020
1,760
1,950
864
600
410
ESR
Rated ripple current
(mΩ max./20℃, 100k to 300kHz) (mArms/105℃, 100kHz)
7
8
13
13
18
28
5,000
5,000
4,460
4,460
3,790
3,040
Part No.
APXJ2R5ARA821MF80G
APXJ6R3ARA561MF80G
APXJ100ARA391MF80G
APXJ160ARA271MF80G
APXJ200ARA151MF80G
APXJ250ARA820MF80G
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
31
CAT. No. E1001P
Similar pages