AD ADA4522-1ARZ-RL 55 v, emi enhanced, zero drift, ultralow noise, rail-to-rail output operational amplifier Datasheet

55 V, EMI Enhanced, Zero Drift, Ultralow Noise,
Rail-to-Rail Output Operational Amplifiers
ADA4522-1/ADA4522-2/ADA4522-4
Data Sheet
PIN CONNECTION DIAGRAM
Low offset voltage: 5 µV maximum
Extremely low offset voltage drift: 22 nV/°C maximum
Low voltage noise density: 5.8 nV/√Hz typical
117 nV p-p typical from 0.1 Hz to 10 Hz
Low input bias current: 50 pA typical
Unity-gain crossover: 3 MHz typical
Single-supply operation: input voltage range includes
ground and rail-to-rail output
Wide range of operating voltages
Single-supply operation: 4.5 V to 55 V
Dual-supply operation: ±2.25 V to ±27.5 V
Integrated EMI filters
Unity-gain stable
8
V+
–IN A 2
ADA4522-2
7
OUT B
+IN A 3
TOP VIEW
(Not to Scale)
6
–IN B
5
+IN B
OUT A 1
V– 4
13168-001
FEATURES
Figure 1. 8-Lead MSOP (RM Suffix) and 8-Lead SOIC (R Suffix)
Pin Configuration
APPLICATIONS
For the ADA4522-1 and ADA4522-4 pin connections and for
more information about the pin connections for these products,
see the Pin Configurations and Function Descriptions section.
100
GENERAL DESCRIPTION
The ADA4522-1/ADA4522-2/ADA4522-4 are single/dual/quad
channel, zero drift op amps with low noise and power, ground
sensing inputs, and rail-to-rail output, optimized for total
accuracy over time, temperature, and voltage conditions. The
wide operating voltage and temperature ranges, as well as the
high open-loop gain and very low dc and ac errors make the
devices well suited for amplifying very small input signals and
for accurately reproducing larger signals in a wide variety of
applications.
The ADA4522-1/ADA4522-2/ADA4522-4 performance is
specified at 5.0 V, 30 V, and 55 V power supply voltages. These
devices operate over the range of 4.5 V to 55 V, and are excellent
for applications using single-ended supplies of 5 V, 10 V, 12 V,
and 30 V, or for applications using higher single supplies and
dual supplies of ±2.5 V, ±5 V, and ±15 V. The ADA4522-1/
ADA4522-2/ADA4522-4 use on-chip filtering to achieve high
immunity to electromagnetic interference (EMI).
The ADA4522-1/ADA4522-2/ADA4522-4 are fully specified
over the extended industrial temperature range of −40°C to
+125°C and are available in 8-lead MSOP, 8-lead SOIC, 14-lead
SOIC, and 14-lead TSSOP packages.
Rev. E
5V
30V
55V
AV = 100
10
1
0.1
10
100
1k
10k
100k
1M
FREQUENCY (Hz)
13168-165
VOLTAGE NOISE DENSITY (nV/√Hz)
Inductance, capacitance, and resistance (LCR)
meter/megohmmeter front-end amplifiers
Load cell and bridge transducers
Magnetic force balance scales
High precision shunt current sensing
Thermocouple/resistance temperature detector (RTD) sensors
Programmable logic controller (PLC) input and output
amplifiers
Figure 2. Voltage Noise Density vs. Frequency, VSY = ±15 V
Table 1. Zero Drift Op Amps (<0.1 µV/°C)
Supply Voltage
Single
Dual
Quad
5V
ADA4528-1
AD8628
AD8538
ADA4051-1
ADA4528-2
AD8629
AD8539
ADA4051-2
AD8630
16 V
AD8638
AD8639
30 V
ADA4638-1
55 V
ADA4522-1
ADA4522-2
ADA4522-4
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2015–2016 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADA4522-1/ADA4522-2/ADA4522-4
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Input Protection ......................................................................... 22
Applications ....................................................................................... 1
Single-Supply and Rail-to-Rail Output ................................... 23
General Description ......................................................................... 1
Large Signal Transient Response .............................................. 23
Pin Connection Diagram ................................................................ 1
Noise Considerations ................................................................. 24
Revision History ............................................................................... 2
EMI Rejection Ratio .................................................................. 25
Specifications..................................................................................... 3
Capacitive Load Stability ........................................................... 25
Electrical Characteristics—5.0 V Operation ............................ 3
Applications Information .............................................................. 27
Electrical Characteristics—30 V Operation ............................. 4
Single-Supply Instrumentation Amplifier .............................. 27
Electrical Characteristics—55 V Operation ............................. 5
Load Cell/Strain Gage Sensor Signal Conditioning Using the
ADA4522-2 .................................................................................. 27
Absolute Maximum Ratings ............................................................ 7
Thermal Resistance ...................................................................... 7
Precision Low-Side Current Shunt Sensor.............................. 28
ESD Caution .................................................................................. 7
Printed Circuit Board Layout ................................................... 28
Pin Configurations and Function Descriptions ........................... 8
Comparator Operation .............................................................. 29
Typical Performance Characteristics ........................................... 10
Outline Dimensions ....................................................................... 30
Theory of Operation ...................................................................... 21
Ordering Guide .......................................................................... 32
On-Chip Input EMI Filter and Clamp Circuit ....................... 22
Thermal Shutdown ..................................................................... 22
REVISION HISTORY
10/2016—Rev. D to Rev. E
Changes to Figure 73 ...................................................................... 23
4/2016—Rev. C to Rev. D
Changed ADA4522-4 Pin 4 to V+ .............................. Throughout
Changed ADA4522-4 Pin 11 to V− ............................ Throughout
Changes to Figure 5 and Table 9 ..................................................... 9
2/2016—Rev. B to Rev. C
Added ADA4522-1 ............................................................. Universal
Changes to Common-Mode Rejection Ratio Parameter and
Supply Current per Amplifier Parameter, Table 2 ........................ 3
Changes to Offset Voltage Drift Parameter, and Supply Current
per Amplifier Parameter, Table 3.................................................... 4
Changes to Offset Voltage Drift Parameter, Input Offset Current
Parameter, and Supply Current per Amplifier Parameter,
Table 4 ................................................................................................ 5
Added Figure 3 and Table 7; Renumbered Sequentially ............. 8
Moved Theory of Operation Section ........................................... 21
Changes to Figure 71 ...................................................................... 21
Changes to Figure 72 ...................................................................... 22
Changes to Ordering Guide .......................................................... 32
10/2015—Rev. 0 to Rev. A
Added ADA4522-4............................................................. Universal
Changes to General Description Section .......................................1
Change to Common-Mode Rejection Ratio Parameter, Table 2...3
Change to Offset Voltage Drift Parameter, Table 3 .......................4
Change to Offset Voltage Drift Parameter and Input Offset
Current Parameter, Table 4 ..............................................................5
Changes to Table 6.............................................................................7
Added Figure 4 and Table 8; Renumbered Sequentially ..............8
Changes to Figure 34...................................................................... 13
Changes to Figure 67...................................................................... 19
Changes to Applications Information Section ........................... 20
Changes to Thermal Shutdown Section ...................................... 21
Changes to Single-Supply Instrumentation Amplifier Section ...... 25
Changes to Precision Low-Side Current Shunt Sensor Section ..... 27
Changes to Printed Circuit Board Layout Section............................. 28
Added Figure 89 and Figure 90; Outline Dimensions ............... 30
Changes to Ordering Guide .......................................................... 30
5/2015—Revision 0: Initial Version
1/2016—Rev. A to Rev. B
Updated Outline Dimensions ....................................................... 29
Rev. E | Page 2 of 32
Data Sheet
ADA4522-1/ADA4522-2/ADA4522-4
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS—5.0 V OPERATION
VSY = 5.0 V, VCM = VSY/2 V, TA = 25°C, unless otherwise specified.
Table 2.
Parameter
INPUT CHARACTERISTICS
Offset Voltage
Offset Voltage Drift
Input Bias Current
Symbol
Test Conditions/Comments
VOS
VCM = VSY/2
−40°C ≤ TA ≤ +125°C
Min
TCVOS
IB
Typ
Max
Unit
0.7
5
6.5
15
150
500
2
250
350
500
3.5
µV
µV
nV/°C
pA
pA
nA
pA
pA
pA
V
dB
dB
dB
dB
dB
2.5
50
−40°C ≤ TA ≤ +85°C
−40°C ≤ TA ≤ +125°C
Input Offset Current
IOS
80
−40°C ≤ TA ≤ +85°C
−40°C ≤ TA ≤ +125°C
Input Voltage Range
Common-Mode Rejection Ratio
IVR
CMRR
Large Signal Voltage Gain
AV
Input Resistance
Differential Mode
Common Mode
Input Capacitance
Differential Mode
Common Mode
OUTPUT CHARACTERISTICS
Output Voltage
High
Low
ADA4522-1, ADA4522-2, VCM = 0 V to 3.5 V
ADA4522-4, VCM = 0 V to 3.5 V
−40°C ≤ TA ≤ +125°C
RL = 10 kΩ, VOUT = 0.5 V to 4.5 V
−40°C ≤ TA ≤ +125°C
0
135
130
130
125
125
30
100
kΩ
GΩ
CINDM
CINCM
7
35
pF
pF
4.98
V
V
mV
mV
mA
mA
mA
mA
mA
Ω
VOH
VOL
IOUT
ISC+
Short-Circuit Current Sink
ISC−
RL = 10 kΩ to VSY/2
−40°C ≤ TA ≤ +125°C
RL = 10 kΩ to VSY/2
−40°C ≤ TA ≤ +125°C
Dropout voltage = 1 V
4.97
4.95
20
DYNAMIC PERFORMANCE
Slew Rate
ZOUT
PSRR
ISY
SR+
SR−
TA = 125°C
f = 1 MHz, AV = 1
VSY = 4.5 V to 55 V
−40°C ≤ TA ≤ +125°C
ADA4522-2, ADA4522-4, IOUT = 0 mA
ADA4522-2, ADA4522-4, −40°C ≤ TA ≤ +125°C
ADA4522-1, IOUT = 0 mA
ADA4522-1, −40°C ≤ TA ≤ +125°C
RL = 10 kΩ, CL = 50 pF, AV = 1
RL = 10 kΩ, CL = 50 pF, AV = 1
Rev. E | Page 3 of 32
30
50
14
22
15
29
19
4
TA = 125°C
Supply Current per Amplifier
145
RINDM
RINCM
Continuous Output Current
Short-Circuit Current Source
Closed-Loop Output Impedance
POWER SUPPLY
Power Supply Rejection Ratio
155
145
150
145
160
830
840
1.4
1.3
900
950
910
970
dB
dB
µA
µA
µA
µA
V/µs
V/µs
ADA4522-1/ADA4522-2/ADA4522-4
Parameter
Gain Bandwidth Product
Unity-Gain Crossover
−3 dB Closed-Loop Bandwidth
Phase Margin
Settling Time to 0.1%
Channel Separation
EMI Rejection Ratio of +IN/+IN x
NOISE PERFORMANCE
Total Harmonic Distortion Plus Noise
Bandwidth (BW) = 80 kHz
BW = 500 kHz
Peak-to-Peak Voltage Noise
Voltage Noise Density
Peak-to-Peak Current Noise
Current Noise Density
Data Sheet
Symbol
GBP
UGC
f−3 dB
ΦM
tS
CS
EMIRR
Test Conditions/Comments
VIN = 10 mV p-p, RL = 10 kΩ, CL = 50 pF, AV = 100
VIN = 10 mV p-p, RL = 10 kΩ, CL = 50 pF, AV = 1
VIN = 10 mV p-p, RL = 10 kΩ, CL = 50 pF, AV = 1
VIN = 10 mV p-p, RL = 10 kΩ, CL = 50 pF, AV = 1
VIN = 1 V step, RL = 10 kΩ, CL = 50 pF, AV = 1
VIN = 1 V p-p, f = 10 kHz, RL = 10 kΩ, CL = 50 pF
VIN = 100 mV peak, f = 400 MHz
VIN = 100 mV peak, f = 900 MHz
VIN = 100 mV peak, f = 1800 MHz
VIN = 100 m peak, f = 2400 MHz
THD + N
AV = 1, f = 1 kHz, VIN = 0.6 V rms
eN p-p
eN
iN p-p
iN
Min
Typ
2.7
3
6.5
64
4
98
72
80
83
85
Max
0.001
0.02
117
5.8
16
0.8
AV = 100, f = 0.1 Hz to 10 Hz
AV = 100, f = 1 kHz
AV = 100, f = 0.1 Hz to 10 Hz
AV = 100, f = 1 kHz
Unit
MHz
MHz
MHz
Degrees
µs
dB
dB
dB
dB
dB
%
%
nV p-p
nV/√Hz
pA p-p
pA/√Hz
ELECTRICAL CHARACTERISTICS—30 V OPERATION
VSY = 30 V, VCM = VSY/2 V, TA = 25°C, unless otherwise specified.
Table 3.
Parameter
INPUT CHARACTERISTICS
Offset Voltage
Symbol
Test Conditions/Comments
VOS
VCM = VSY/2
−40°C ≤ TA ≤ +125°C
ADA4522-1, ADA4522-2
ADA4522-4
Offset Voltage Drift
TCVOS
Input Bias Current
IB
Min
Typ
Max
Unit
1
5
7.2
22
25
150
500
3
300
400
500
28.5
µV
µV
nV/°C
nV/°C
pA
pA
nA
pA
pA
pA
V
dB
dB
dB
dB
4
5.3
50
−40°C ≤ TA ≤ +85°C
−40°C ≤ TA ≤ +125°C
Input Offset Current
IOS
80
−40°C ≤ TA ≤ +85°C
−40°C ≤ TA ≤ +125°C
Input Voltage Range
Common-Mode Rejection Ratio
IVR
CMRR
Large Signal Voltage Gain
AV
Input Resistance
Differential Mode
Common Mode
Input Capacitance
Differential Mode
Common Mode
OUTPUT CHARACTERISTICS
Output Voltage
High
Low
Continuous Output Current
VCM = 0 V to 28.5 V
−40°C ≤ TA ≤ +125°C
RL = 10 kΩ, VOUT = 0.5 V to 29.5 V
−40°C ≤ TA ≤ +125°C
0
145
140
140
135
160
150
RINDM
RINCM
30
400
kΩ
GΩ
CINDM
CINCM
7
35
pF
pF
29.89
V
V
mV
mV
mA
VOH
VOL
IOUT
RL = 10 kΩ to VSY/2
−40°C ≤ TA ≤ +125°C
RL = 10 kΩ to VSY/2
−40°C ≤ TA ≤ +125°C
Dropout voltage = 1 V
Rev. E | Page 4 of 32
29.87
29.80
110
14
130
200
Data Sheet
Parameter
Short-Circuit Current Source
ADA4522-1/ADA4522-2/ADA4522-4
Symbol
ISC+
Test Conditions/Comments
Min
Typ
21
15
33
22
4
150
145
160
TA = 125°C
Short-Circuit Current Sink
Closed-Loop Output Impedance
POWER SUPPLY
Power Supply Rejection Ratio
Supply Current per Amplifier
DYNAMIC PERFORMANCE
Slew Rate
Gain Bandwidth Product
Unity-Gain Crossover
−3 dB Closed-Loop Bandwidth
Phase Margin
Settling Time to 0.1%
Settling Time to 0.01%
Channel Separation
EMI Rejection Ratio of +IN/+IN x
NOISE PERFORMANCE
Total Harmonic Distortion Plus Noise
BW = 80 kHz
BW = 500 kHz
Peak-to-Peak Voltage Noise
Voltage Noise Density
Peak-to-Peak Current Noise
Current Noise Density
ISC−
ZOUT
PSRR
ISY
TA = 125°C
f = 1 MHz, AV = 1
VSY = 4.5 V to 55 V
−40°C ≤ TA ≤ +125°C
ADA4522-2, ADA4522-4, IOUT = 0 mA
ADA4522-2, ADA4522-4, −40°C ≤ TA ≤ +125°C
ADA4522-1, IOUT = 0 mA
ADA4522-1, −40°C ≤ TA ≤ +125°C
SR+
SR−
GBP
UGC
f−3 dB
ΦM
tS
tS
CS
EMIRR
RL = 10 kΩ, CL = 50 pF, AV = 1
RL = 10 kΩ, CL = 50 pF, AV = 1
VIN = 10 mV p-p, RL = 10 kΩ, CL = 50 pF, AV = 100
VIN = 10 mV p-p, RL = 10 kΩ, CL = 50 pF, AV = 1
VIN = 10 mV p-p, RL = 10 kΩ, CL = 50 pF, AV = 1
VIN = 10 mV p-p, RL = 10 kΩ, CL = 50 pF, AV = 1
VIN = 10 V step, RL = 10 kΩ, CL = 50 pF, AV = 1
VIN = 10 V step, RL = 10 kΩ, CL = 50 pF, AV = 1
VIN = 10 V p-p, f = 10 kHz, RL = 10 kΩ, CL = 50 pF
VIN = 100 mV peak, f = 400 MHz
VIN = 100 mV peak, f = 900 MHz
VIN = 100 mV peak, f = 1800 MHz
VIN = 100 mV peak, f = 2400 MHz
THD + N
AV = 1, f = 1 kHz, VIN = 6 V rms
eN p-p
eN
iN p-p
iN
830
840
AV = 100, f = 0.1 Hz to 10 Hz
AV = 100, f = 1 kHz
AV = 100, f = 0.1 Hz to 10 Hz
AV = 100, f = 1 kHz
Max
900
950
910
970
Unit
mA
mA
mA
mA
Ω
dB
dB
µA
µA
µA
µA
1.8
0.9
2.7
3
6.5
64
12
14
98
72
80
83
85
V/µs
V/µs
MHz
MHz
MHz
Degrees
µs
µs
dB
dB
dB
dB
dB
0.0005
0.004
117
5.8
16
0.8
%
%
nV p-p
nV/√Hz
pA p-p
pA/√Hz
ELECTRICAL CHARACTERISTICS—55 V OPERATION
VSY = 55 V, VCM = VSY/2 V, TA = 25°C, unless otherwise specified.
Table 4.
Parameter
INPUT CHARACTERISTICS
Offset Voltage
Symbol
Test Conditions/Comments
VOS
VCM = VSY/2
−40°C ≤ TA ≤ +125°C
ADA4522-1, ADA4522-2
ADA4522-4
Offset Voltage Drift
TCVOS
Input Bias Current
IB
Min
Typ
Max
Unit
1.5
7
10
30
40
150
500
4.5
300
400
500
550
µV
µV
nV/°C
nV/°C
pA
pA
nA
pA
pA
pA
pA
6
9
50
−40°C ≤ TA ≤ +85°C
−40°C ≤ TA ≤ +125°C
Input Offset Current
IOS
80
−40°C ≤ TA ≤ +85°C
ADA4522-1, ADA4522-2, −40°C ≤ TA ≤ +125°C
ADA4522-4, −40°C ≤ TA ≤ +125°C
Rev. E | Page 5 of 32
ADA4522-1/ADA4522-2/ADA4522-4
Parameter
Input Voltage Range
Common-Mode Rejection Ratio
Large Signal Voltage Gain
Input Resistance
Differential Mode
Common Mode
Input Capacitance
Differential Mode
Common Mode
OUTPUT CHARACTERISTICS
Output Voltage
High
Low
Symbol
IVR
CMRR
AV
Data Sheet
Test Conditions/Comments
VCM = 0 V to 53.5 V
−40°C ≤ TA ≤ +125°C
RL = 10 kΩ, VOUT = 0.5 V to 54.5 V
−40°C ≤ TA ≤ +125°C
Min
0
140
135
135
125
CINDM
CINCM
7
35
pF
pF
54.8
V
V
mV
mV
mA
mA
mA
mA
mA
Ω
VOH
VOL
ISC−
RL = 10 kΩ to VSY/2
−40°C ≤ TA ≤ +125°C
RL = 10 kΩ to VSY/2
−40°C ≤ TA ≤ +125°C
Dropout voltage = 1 V
54.75
54.65
200
NOISE PERFORMANCE
Total Harmonic Distortion Plus Noise
BW = 80 kHz
BW = 500 kHz
Peak-to-Peak Voltage Noise
Voltage Noise Density
Peak-to-Peak Current Noise
Current Noise Density
ZOUT
PSRR
ISY
TA = 125°C
f = 1 MHz, AV = 1
VSY = 4.5 V to 55 V
−40°C ≤ TA ≤ +125°C
ADA4522-2, ADA4522-4, IOUT = 0 mA
ADA4522-2, ADA4522-4, −40°C ≤ TA ≤ +125°C
ADA4522-1, IOUT = 0 mA
ADA4522-1, −40°C ≤ TA ≤ +125°C
SR+
SR−
GBP
UGC
f−3 dB
ΦM
tS
tS
CS
EMIRR
RL = 10 kΩ, CL = 50 pF, AV = 1
RL = 10 kΩ, CL = 50 pF, AV = 1
VIN = 10 mV p-p, RL = 10 kΩ, CL = 50 pF, AV = 100
VIN = 10 mV p-p, RL = 10 kΩ, CL = 50 pF, AV = 1
VIN = 10 mV p-p, RL = 10 kΩ, CL = 50 pF, AV = 1
VIN = 10 mV p-p, RL = 10 kΩ, CL = 50 pF, AV = 1
VIN = 10 V step, RL = 10 kΩ, CL = 50 pF, AV = 1
VIN = 10 V step, RL = 10 kΩ, CL = 50 pF, AV = 1
VIN = 10 V p-p, f = 10 kHz, RL = 10 kΩ, CL = 50 pF
VIN = 100 mV peak, f = 400 MHz
VIN = 100 mV peak, f = 900 MHz
VIN = 100 mV peak, f = 1800 MHz
VIN = 100 mV peak, f = 2400 MHz
THD + N
AV = 1, f = 1 kHz, VIN = 10 V rms
eN p-p
eN
iN p-p
iN
AV = 100, f = 0.1 Hz to 10 Hz
AV = 100, f = 1 kHz
AV = 100, f = 0.1 Hz to 10 Hz
AV = 100, f = 1 kHz
Rev. E | Page 6 of 32
250
350
14
21
15
32
22
4
TA = 125°C
Gain Bandwidth Product
Unity-Gain Crossover
−3 dB Closed-Loop Bandwidth
Phase Margin
Settling Time to 0.1%
Settling Time to 0.01%
Channel Separation
EMI Rejection Ratio of +IN/+IN x
137
kΩ
GΩ
Short-Circuit Current Sink
DYNAMIC PERFORMANCE
Slew Rate
144
Unit
V
dB
dB
dB
dB
30
1000
IOUT
ISC+
Supply Current per Amplifier
Max
53.5
RINDM
RINCM
Continuous Output Current
Short-Circuit Current Source
Closed-Loop Output Impedance
POWER SUPPLY
Power Supply Rejection Ratio
Typ
150
145
160
830
840
900
950
910
970
dB
dB
µA
µA
µA
µA
1.7
0.8
2.7
3
6.5
64
12
14
98
72
80
83
85
V/µs
V/µs
MHz
MHz
MHz
Degrees
µs
µs
dB
dB
dB
dB
dB
0.0007
0.003
117
5.8
16
0.8
%
%
nV p-p
nV/√Hz
pA p-p
pA/√Hz
Data Sheet
ADA4522-1/ADA4522-2/ADA4522-4
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 5.
Parameter
Supply Voltage
Input Voltage
Input Current1
Differential Input Voltage
Output Short-Circuit
Duration to Ground
Temperature Range
Storage
Operating
Junction
Lead Temperature (Soldering,
60 sec)
1
Rating
60 V
(V−) − 300 mV to (V+) + 300 mV
±10 mA
±5 V
Indefinite
−65°C to +150°C
−40°C to +125°C
−65°C to +150°C
300°C
θJA is specified for the worst case conditions, that is, a device
soldered in a circuit board for surface-mount packages using a
standard 4-layer JEDEC board.
Table 6. Thermal Resistance
Package Type
8-Lead MSOP (RM-8)
8-Lead SOIC (R-8)
14-Lead TSSOP (RU-14)
14-Lead SOIC (R-14)
ESD CAUTION
The input pins have clamp diodes to the power supply pins. Limit the input
current to ±10 mA or less whenever input signals exceed the power supply
rail by 300 mV.
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Rev. E | Page 7 of 32
θJA
194
122
112
115
θJC
38
41
43
36
Unit
°C/W
°C/W
°C/W
°C/W
ADA4522-1/ADA4522-2/ADA4522-4
Data Sheet
NIC 1
8
NIC
–IN 2
ADA4522-1
7
V+
+IN 3
TOP VIEW
(Not to Scale)
6
OUT
5
NIC
V– 4
NOTES
1. NIC = NOT INTERNALLY CONNECTED.
13168-101
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
Figure 3. ADA4522-1 Pin Configuration
Table 7. ADA4522-1 Pin Function Descriptions
Mnemonic
NIC
−IN
+IN
V−
OUT
V+
Description
Not Internally Connected
Inverting Input
Noninverting Input
Negative Supply Voltage
Output
Positive Supply Voltage
OUT A 1
8
V+
–IN A 2
ADA4522-2
7
OUT B
+IN A 3
TOP VIEW
(Not to Scale)
6
–IN B
5
+IN B
V– 4
13168-002
Pin No.
1, 5, 8
2
3
4
6
7
Figure 4. ADA4522-2 Pin Configuration
Table 8. ADA4522-2 Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
Mnemonic
OUT A
−IN A
+IN A
V−
+IN B
−IN B
OUT B
V+
Description
Output, Channel A
Inverting Input, Channel A
Noninverting Input, Channel A
Negative Supply Voltage
Noninverting Input, Channel B
Inverting Input, Channel B
Output, Channel B
Positive Supply Voltage
Rev. E | Page 8 of 32
Data Sheet
ADA4522-1/ADA4522-2/ADA4522-4
OUT A 1
14 OUT D
13 –IN D
2
+IN A 3
ADA4522-4
12 +IN D
V+
4
+IN B
5
–IN B
6
9
–IN C
OUT B
7
8
OUT C
TOP VIEW
(Not to Scale)
11 V–
10 +IN C
13168-189
–IN A
Figure 5. ADA4522-4 Pin Configuration
Table 9. ADA4522-4 Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Mnemonic
OUT A
−IN A
+IN A
V+
+IN B
−IN B
OUT B
OUT C
−IN C
+IN C
V−
+IN D
−IN D
OUT D
Description
Output, Channel A
Inverting Input, Channel A
Noninverting Input, Channel A
Positive Supply Voltage
Noninverting Input, Channel B
Inverting Input, Channel B
Output, Channel B
Output, Channel C
Inverting Input, Channel C
Noninverting Input, Channel C
Negative Supply Voltage
Noninverting Input, Channel D
Inverting Input, Channel D
Output, Channel D
Rev. E | Page 9 of 32
ADA4522-1/ADA4522-2/ADA4522-4
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, unless otherwise noted.
NUMBER OF AMPLIFIERS
80
70
35
VSY = ±2.5V
VCM = VSY/2
600 CHANNELS
MEAN = 0.10µV
STD DEV. = 0.59µV
30
NUMBER OF AMPLIFIERS
90
60
50
40
30
VSY = ±2.5V
–40°C ≤ TA ≤ +125°C
160 CHANNELS
MEAN = –1.19nV/°C
STD DEV. = 1.82nV/°C
25
20
15
10
20
–4
–3
–2
–1
0
1
2
3
4
5
VOS (µV)
0
–30 –25 –20 –15 –10
13168-003
0
–5
30
50
40
30
20
–3
–2
–1
0
1
2
3
4
5
VOS (µV)
20
25
30
VSY = ±15V
–40°C ≤ TA ≤ +125°C
160 CHANNELS
MEAN = –2.48nV/°C
STD DEV. = 2.65nV/°C
25
20
15
10
0
–30 –25 –20 –15 –10
–5
0
5
10
15
20
25
30
TCVOS (nV/°C)
Figure 7. Input Offset Voltage Distribution, VSY = ±15 V
Figure 10. Input Offset Voltage Drift Distribution, VSY = ±15 V
35
VSY = ±27.5V
VCM = VSY/2
600 CHANNELS
MEAN = 0.69µV
STD DEV. = 0.81µV
NUMBER OF AMPLIFIERS
30
50
40
30
20
10
VSY = ±27.5V
–40°C ≤ TA ≤ +125°C
160 CHANNELS
MEAN = –4.54nV/°C
STD DEV. = 4.01nV/°C
25
20
15
10
5
0
–5
–4
–3
–2
–1
0
1
2
3
4
VOS (µV)
5
13168-005
NUMBER OF AMPLIFIERS
15
13168-007
–4
13168-004
0
–5
60
10
5
10
70
5
Figure 8. Input Offset Voltage Distribution, VSY = ±27.5 V
0
–30 –25 –20 –15 –10
–5
0
5
10
15
20
25
30
TCVOS (nV/°C)
Figure 11. Input Offset Voltage Drift Distribution, VSY = ±27.5 V
Rev. E | Page 10 of 32
13168-008
60
35
VSY = ±15V
VCM = VSY/2
600 CHANNELS
MEAN = 0.31µV
STD DEV. = 0.62µV
NUMBER OF AMPLIFIERS
NUMBER OF AMPLIFIERS
70
0
Figure 9. Input Offset Voltage Drift Distribution, VSY = ±2.5 V
Figure 6. Input Offset Voltage Distribution, VSY = ±2.5 V
80
–5
TCVOS (nV/°C)
13168-006
5
10
2000
VSY = 5V
20 CHANNELS
1500
1
1000
VSY = 5V
+125°C
+85°C
+25°C
–40°C
IB (pA)
3
–1
500
–3
0
–5
0
1.0
2.0
3.0
3.5
VCM (V)
Figure 12. Input Offset Voltage (VOS) vs. Common-Mode Voltage (VCM), VSY = 5 V
5
–500
13168-009
VOS (µV)
5
ADA4522-1/ADA4522-2/ADA4522-4
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
VCM (V)
13168-012
Data Sheet
Figure 15. Input Bias Current (IB) vs. Common-Mode Voltage (VCM), VSY = 5 V
3000
VSY = 30V
20 CHANNELS
VSY = 30V
2500
3
1
IB (pA)
VOS (µV)
2000
–1
+125°C
+85°C
+25°C
–40°C
1500
1000
500
–3
0
5.0
10.0
15.0
20.0
25.0
28.5
VCM (V)
–500
13168-010
–5
0
10.0
15.0
20.0
25.0
28.5
VCM (V)
Figure 13. Input Offset Voltage (VOS) vs. Common-Mode Voltage (VCM),
VSY = 30 V
5
5.0
13168-013
0
Figure 16. Input Bias Current (IB) vs. Common-Mode Voltage (VCM), VSY = 30 V
VSY = 55V
20 CHANNELS
5000
VSY = 55V
4500
3
4000
+125°C
+85°C
+25°C
–40°C
3000
IB (pA)
VOS (µV)
3500
1
–1
2500
2000
1500
1000
–3
500
5.0
13168-011
0
10.0 15.0 20.0 25.0 30.0 35.0 40.0 45.0 50.0 53.5
VCM (V)
Figure 14. Input Offset Voltage (VOS) vs. Common-Mode Voltage (VCM),
VSY = 55 V
Rev. E | Page 11 of 32
–500
0
5.0
10.0 15.0 20.0 25.0 30.0 35.0 40.0 45.0 50.0 53.5
VCM (V)
Figure 17. Input Bias Current (IB) vs. Common-Mode Voltage (VCM),
VSY = 55 V
13168-014
0
–5
ADA4522-1/ADA4522-2/ADA4522-4
2000
IB (pA)
2500
800
IB (pA)
1000
600
1500
400
1000
200
500
0
0
–200
–500
–25
0
25
50
75
100
125
TEMPERATURE (°C)
–1000
–50
13168-015
–400
–50
IB+
IB–
IOS
ISY PER AMPLIFIER (mA)
IB (pA)
50
75
100
125
0.8
1000
500
0.6
0.4
0.2
0
–25
0
25
50
75
100
125
TEMPERATURE (°C)
0
100k
15
20
25
30
35
40
45
50
55
60
+125°C
+85°C
+25°C
–40°C
VSY = ±2.5V TO ±27.5V
OUTPUT VOLTAGE LOW (VOL)
TO SUPPLY RAIL (mV)
10k
1k
100
10
1
1k
100
10
1
0.01
0.1
ILOAD (mA)
1
10
100
0.1
0.001
13168-024
0.1
0.001
10
Figure 22. Supply Current (ISY) per Amplifier vs. Supply Voltage (VSY)
+125°C
+85°C
+25°C
–40°C
10k
5
VSY (V)
Figure 19. Input Bias Current (IB) vs. Temperature, VSY = ±15 V
VSY = ±2.5V TO ±27.5V
+125°C
+85°C
+25°C
–40°C
0
13168-017
–500
–50
OUTPUT VOLTAGE HIGH (VOH)
TO SUPPLY RAIL (mV)
25
1.0
1500
100k
0
Figure 21. Input Bias Current (IB) vs. Temperature, VSY = ±27.5 V
VSY = ±15V
VCM = VSY/2
2000
–25
TEMPERATURE (°C)
Figure 18. Input Bias Current (IB) vs. Temperature, VSY = ±2.5 V
2500
IB+
IB–
IOS
3000
13168-016
IB+
IB–
IOS
1200
VSY = ±27.5V
VCM = VSY/2
3500
13168-025
1400
4000
VSY = ±2.5V
VCM = VSY/2
Figure 20. Output Voltage High (VOH) to Supply Rail vs. Load Current (ILOAD)
0.01
0.1
1
ILOAD (mA)
10
100
13168-027
1600
Data Sheet
Figure 23. Output Voltage Low (VOL) to Supply Rail vs. Load Current (ILOAD)
Rev. E | Page 12 of 32
150
VSY = ±2.5V
OUTPUT VOLTAGE LOW (VOL)
TO SUPPLY RAIL (mV)
125
RL = 2kΩ
100
75
50
RL = 10kΩ
25
0
–50
–25
0
25
50
75
100
125
150
TEMPERATURE (°C)
50
200
RL = 10kΩ
–25
0
25
50
75
100
125
150
VSY = ±15V
150
RL = 10kΩ
125
100
75
50
–25
0
25
50
75
100
125
150
TEMPERATURE (°C)
Figure 25. Output Voltage High (VOH) to Supply Rail vs. Temperature, VSY = ±15 V
100
75
50
RL = 100kΩ
0
–50
–25
0
25
50
75
100
125
150
TEMPERATURE (°C)
Figure 28. Output Voltage Low (VOL) to Supply Rail vs. Temperature, VSY = ±15 V
350
VSY = ±27.5V
300
VSY = ±27.5V
RL = 10kΩ
200
150
100
50
25
50
75
100
125
13168-020
0
200
150
100
50
RL = 100kΩ
–25
RL = 10kΩ
250
150
TEMPERATURE (°C)
Figure 26. Output Voltage High (VOH) to Supply Rail vs. Temperature,
VSY = ±27.5 V
Rev. E | Page 13 of 32
0
–50
RL = 100kΩ
–25
0
25
50
75
100
125
150
TEMPERATURE (°C)
Figure 29. Output Voltage Low (VOL) to Supply Rail vs. Temperature,
VSY = ±27.5 V
13168-023
OUTPUT VOLTAGE LOW (VOL)
TO SUPPLY RAIL (mV)
300
250
0
–50
RL = 10kΩ
125
25
RL = 100kΩ
0
–50
150
13168-022
OUTPUT VOLTAGE LOW (VOL)
TO SUPPLY RAIL (mV)
175
13168-019
OUTPUT VOLTAGE HIGH (VOH)
TO SUPPLY RAIL (mV)
75
Figure 27. Output Voltage Low (VOL) to Supply Rail vs. Temperature,
VSY = ±2.5 V
VSY = ±15V
25
OUTPUT VOLTAGE HIGH (VOH)
TO SUPPLY RAIL (mV)
RL = 2kΩ
100
TEMPERATURE (°C)
175
350
125
0
–50
Figure 24. Output Voltage High (VOH) to Supply Rail vs. Temperature,
VSY = ±2.5 V
200
VSY = ±2.5V
25
13168-018
OUTPUT VOLTAGE HIGH (VOH)
TO SUPPLY RAIL (mV)
150
ADA4522-1/ADA4522-2/ADA4522-4
13168-021
Data Sheet
ADA4522-1/ADA4522-2/ADA4522-4
140
Data Sheet
140
VSY = ±2.5V TO ±27.5V
120
100
100
CMRR (dB)
120
80
PSRR (dB)
80
60
PSRR+
PSRR–
VSY = ±2.5V TO ±27.5V
60
40
40
20
20
1k
10k
100k
1M
10M
FREQUENCY (Hz)
–20
100
1k
10k
100k
1M
10M
13168-032
100
13168-030
0
0
10
100M
FREQUENCY (Hz)
Figure 30. CMRR vs. Frequency
1k
AV = 100
AV = 10
AV = 1
0.840
VSY = ±2.5V TO ±27.5V
10
1
0.1
0.01
0.830
0.825
0.820
0.815
10k
100k
1M
10M
100M
FREQUENCY (Hz)
0.805
–50
13168-031
1k
90
60
40
45
GAIN
20
0
50
75
100
125
150
VSY = ±2.5V TO ±27.5V
50
0
40
AV = 100
30
AV = 10
20
10
AV = 1
0
–40
100
1k
10k
100k
1M
10M
–45
FREQUENCY (Hz)
–20
100
1k
10k
100k
1M
FREQUENCY (Hz)
Figure 35. Closed-Loop Gain vs. Frequency
Figure 32. Open-Loop Gain and Phase Margin vs. Frequency
Rev. E | Page 14 of 32
10M
13168-133
–10
VSY = ±2.5V TO ±27.5V
RL = 10kΩ
13168-026
OPEN-LOOP GAIN (dB)
PHASE
80
60
135
CLOSED-LOOP GAIN (dB)
100
25
Figure 34. Supply Current (ISY) per Amplifier vs. Temperature
PHASE MARGIN (Degrees)
CL = 50pF
CL = 100pF
CL = 50pF
CL = 100pF
0
TEMPERATURE (°C)
Figure 31. Closed-Loop Output Impedance vs. Frequency
120
–25
13168-028
0.810
0.001
100
–20
5V
30V
55V
0.835
ISY PER AMPLIFIER (mA)
OUTPUT IMPEDANCE (Ω)
100
Figure 33. PSRR vs. Frequency
Data Sheet
ADA4522-1/ADA4522-2/ADA4522-4
0.04
VOLTAGE (V)
1.0
0.5
0
–0.5
0.02
0
–0.02
–0.04
–1.5
–0.06
13168-034
–1.0
–2.0
TIME (4µs/DIV)
–0.08
TIME (400ns/DIV)
Figure 39. Small Signal Transient Response, VSY = ±2.5 V
Figure 36. Large Signal Transient Response, VSY = ±2.5 V
20
5
0.04
0
–5
0.02
0
–0.02
–0.04
–15
–0.06
13168-035
–10
–20
TIME (10µs/DIV)
–0.08
TIME (400ns/DIV)
Figure 37. Large Signal Transient Response, VSY = ±15 V
Figure 40. Small Signal Transient Response, VSY = ±15 V
30
VSY = ±27.5V
VIN = 100mV p-p
AV = 1
RL = 10kΩ
CL = 100pF
0.06
0.04
VOLTAGE (V)
10
0
–10
0.02
0
–0.02
–0.04
–20
–30
TIME (10µs/DIV)
–0.08
TIME (400ns/DIV)
Figure 41. Small Signal Transient Response, VSY = ±27.5 V
Figure 38. Large Signal Transient Response, VSY = ±27.5 V
Rev. E | Page 15 of 32
13168-039
–0.06
13168-036
VOLTAGE (V)
0.08
VSY = ±27.5V
VIN = 50V p-p
AV = 1
RL = 10kΩ
CL = 100pF
RS_IN+ = 100Ω
RS_IN– = 100Ω
20
VSY = ±15V
VIN = 100mV p-p
AV = 1
RL = 10kΩ
CL = 100pF
0.06
VOLTAGE (V)
10
VOLTAGE (V)
0.08
VSY = ±15V
VIN = 15V p-p
AV = 1
RL = 10kΩ
CL = 100pF
RS_IN+ = 100Ω
RS_IN– = 100Ω
15
VSY = ±2.5V
VIN = 100mV p-p
AV = 1
RL = 10kΩ
CL = 100pF
0.06
13168-037
1.5
VOLTAGE (V)
0.08
VSY = ±2.5V
VIN = 1.5V p-p
AV = 1
RL = 10kΩ
CL = 100pF
RS_IN+ = 100Ω
RS_IN– = 100Ω
13168-038
2.0
ADA4522-1/ADA4522-2/ADA4522-4
45
40
0
VSY = ±2.5V
RL = 10kΩ
AV = 1
VIN = 100mV p-p
–20
CHANNEL SEPARATION (dB)
50
Data Sheet
OVERSHOOT (%)
35
OS+
30
25
OS–
20
15
10
VIN = 0.5V p-p
VIN = 1V p-p
VIN = 2V p-p
VSY = ±2.5V
AV = –10
RL = 10kΩ
–40
–60
–80
–100
–120
100
1000
LOAD CAPACITANCE (pF)
–140
0.01
13168-040
0
10
0
VSY = ±15V
RL = 10kΩ
AV = 1
VIN = 100mV p-p
–20
30
OS+
25
20
OS–
15
10
100
1000
LOAD CAPACITANCE (pF)
–100
0
CHANNEL SEPARATION (dB)
–20
30
OS+
25
20
OS–
15
10
1
10
100
VIN = 10V p-p
VIN = 30V p-p
VIN = 50V p-p
VSY = ±27.5V
AV = –10
RL = 10kΩ
–40
–60
–80
–100
–120
100
LOAD CAPACITANCE (pF)
1000
13168-042
5
0
10
0.1
Figure 46. Channel Separation vs. Frequency, VSY = ±15 V
VSY = ±27.5V
RL = 10kΩ
AV = 1
VIN = 100mV p-p
35
OVERSHOOT (%)
–80
FREQUENCY (kHz)
Figure 43. Small Signal Overshoot vs. Load Capacitance, VSY = ±15 V
40
–60
–140
0.01
13168-041
0
10
45
–40
–120
5
50
VIN = 5V p-p
VIN = 10V p-p
VIN = 25V p-p
VSY = ±15V
AV = –10
RL = 10kΩ
13168-044
OVERSHOOT (%)
35
100
Figure 44. Small Signal Overshoot vs. Load Capacitance, VSY = ±27.5 V
Rev. E | Page 16 of 32
–140
0.01
0.1
1
10
100
FREQUENCY (kHz)
Figure 47. Channel Separation vs. Frequency, VSY = ±27.5 V
13168-045
40
10
Figure 45. Channel Separation vs. Frequency, VSY = ±2.5 V
CHANNEL SEPARATION (dB)
45
1
FREQUENCY (kHz)
Figure 42. Small Signal Overshoot vs. Load Capacitance, VSY = ±2.5 V
50
0.1
13168-043
5
Data Sheet
ADA4522-1/ADA4522-2/ADA4522-4
100
1
80kHz LOW-PASS FILTER
500kHz LOW-PASS FILTER
80kHz LOW-PASS FILTER
500kHz LOW-PASS FILTER
10
0.1
THD + N (%)
THD + N (%)
1
0.1
0.01
0.01
0.001
0.0001
0.001
1
0.1
0.01
AMPLITUDE (V rms)
0.0001
10
VSY = ±2.5V
AV = 1
RL = 10kΩ
VIN = 0.6V rms
1k
10k
100k
FREQUENCY (Hz)
Figure 51. THD + N vs. Frequency, VSY = ±2.5 V
Figure 48. THD + N vs. Amplitude, VSY = ±2.5 V
1
100
100
13168-053
VSY = ±2.5V
AV = 1
FREQUENCY = 1kHz
RL = 10kΩ
13168-050
0.001
80kHz LOW-PASS FILTER
500kHz LOW-PASS FILTER
80kHz LOW-PASS FILTER
500kHz LOW-PASS FILTER
10
0.1
THD + N (%)
THD + N (%)
1
0.1
0.01
0.01
0.001
0.0001
0.001
0.01
0.1
1
10
AMPLITUDE (V rms)
0.0001
10
100
1k
10k
100k
FREQUENCY (Hz)
Figure 52. THD + N vs. Frequency, VSY = ±15 V
Figure 49. THD + N vs. Amplitude, VSY = ±15 V
1
100
VSY = ±15V
AV = 1
RL = 10kΩ
VIN = 6V rms
13168-054
VSY = ±15V
AV = 1
FREQUENCY = 1kHz
RL = 10kΩ
13168-051
0.001
80kHz LOW-PASS FILTER
500kHz LOW-PASS FILTER
80kHz LOW-PASS FILTER
500kHz LOW-PASS FILTER
10
0.1
THD + N (%)
THD + N (%)
1
0.1
0.01
0.01
0.001
0.0001
0.001
0.01
0.1
1
AMPLITUDE (V rms)
10
0.0001
10
VSY = ±27.5V
AV = 1
RL = 10kΩ
VIN = 10V rms
100
1k
10k
FREQUENCY (Hz)
Figure 53. THD + N vs. Frequency, VSY = ±27.5 V
Figure 50. THD + N vs. Amplitude, VSY = ±27.5 V
Rev. E | Page 17 of 32
100k
13168-055
VSY = ±27.5V
AV = 1
FREQUENCY = 1kHz
RL = 10kΩ
13168-052
0.001
ADA4522-1/ADA4522-2/ADA4522-4
0
7
0.4
6
0.2
5
4
VIN
4
–0.4
–0.6
–0.8
VSY = ±2.5V
VIN = 350mV p-p
RL = 10kΩ
CL = 100pF
AV = –10
–1.0
3
2
0
INPUT VOLTAGE (V)
5
OUTPUT VOLTAGE (V)
INPUT VOLTAGE (V)
–0.2
VIN
3
VSY = ±2.5V
VIN = 350mV p-p
RL = 10kΩ
CL = 100pF
AV = –10
–0.2
–0.4
–0.6
2
1
0
VOUT
1
–0.8
–1
0
–1.0
–2
OUTPUT VOLTAGE (V)
0.2
Data Sheet
–1
–1.4
TIME (1µs/DIV)
–1.2
–3
TIME (1µs/DIV)
Figure 57. Negative Overload Recovery, VSY = ±2.5 V
Figure 54. Positive Overload Recovery, VSY = ±2.5 V
35
6
20
0
30
4
15
–2
25
2
2
13168-059
–1.2
13168-056
VOUT
–10
VOUT
–12
–14
–2
–4
5
–6
0
–8
–5
TIME (4µs/DIV)
5
0
VSY = ±15V
VIN = 2V p-p
RL = 10kΩ
CL = 100pF
AV = –10
0
–5
VOUT
–10
–15
–20
–10
TIME (2µs/DIV)
Figure 58. Negative Overload Recovery, VSY = ±15 V
Figure 55. Positive Overload Recovery, VSY = ±15 V
70
6
40
0
60
4
30
–2
50
2
2
OUTPUT VOLTAGE (V)
10
10
VIN
13168-060
–8
15
INPUT VOLTAGE (V)
–3
VSY = ±15V
VIN = 2V p-p
RL = 10kΩ
CL = 100pF
AV = –10
OUTPUT VOLTAGE (V)
20
–4
13168-057
INPUT VOLTAGE (V)
VIN
–10
20
20
VIN
10
0
–2
–4
10
–6
0
–8
VSY = ±27.5V
VIN = 4V p-p
RL = 10kΩ
CL = 100pF
AV = –10
0
–10
VOUT
OUTPUT VOLTAGE (V)
–8
30
INPUT VOLTAGE (V)
–3
40
VSY = ±27.5V
VIN = 4V p-p
RL = 10kΩ
CL = 100pF
AV = –10
OUTPUT VOLTAGE (V)
–4
–20
VOUT
–14
–10
TIME (10µs/DIV)
–30
–40
–10
TIME (4µs/DIV)
Figure 59. Negative Overload Recovery, VSY = ±27.5 V
Figure 56. Positive Overload Recovery, VSY = ±27.5 V
Rev. E | Page 18 of 32
13168-061
–12
13168-058
INPUT VOLTAGE (V)
VIN
Data Sheet
100
10
1
10
100
1k
10k
100k
1M
10M
100M
FREQUENCY (Hz)
10
1
0.1
10
1k
10k
100k
1M
Figure 63. Voltage Noise Density vs. Frequency, AV = 100
100
VSY = ±15V
AV = 1
VSY = ±15V AND ±27.5V
AV = 100
PEAK-TO-PEAK NOISE = 117nV p-p
75
INPUT REFERRED VOLTAGE (nV)
VOLTAGE NOISE DENSITY (nV/√Hz)
100
FREQUENCY (Hz)
Figure 60. Voltage Noise Density vs. Frequency, VSY = ±2.5 V
100
5V
30V
55V
AV = 100
13168-065
VOLTAGE NOISE DENSITY (nV/√Hz)
VSY = ±2.5V
AV = 1
13168-062
VOLTAGE NOISE DENSITY (nV/√Hz)
100
ADA4522-1/ADA4522-2/ADA4522-4
10
50
25
0
–25
–50
1k
10k
100k
1M
10M
100M
FREQUENCY (Hz)
–100
TIME (1s/DIV)
Figure 61. Voltage Noise Density vs. Frequency, VSY = ±15 V
Figure 64. 0.1 Hz to 10 Hz Noise
10
CURRENT NOISE DENSITY (pA/√Hz)
VSY = ±27.5V
AV = 1
10
1
10
100
1k
10k
100k
1M
10M
100M
FREQUENCY (Hz)
13168-064
VOLTAGE NOISE DENSITY (nV/√Hz)
100
13168-066
100
Figure 62. Voltage Noise Density vs. Frequency, VSY = ±27.5 V
RS = 100kΩ
AV = 100
VSY = ±2.5V
VSY = ±15V
VSY = ±27.5V
1
0.1
10
100
1k
10k
FREQUENCY (Hz)
Figure 65. Current Noise Density vs. Frequency
Rev. E | Page 19 of 32
100k
13168-067
1
10
13168-063
–75
Data Sheet
INPUT VOLTAGE (1V/DIV)
INPUT VOLTAGE (1V/DIV)
ADA4522-1/ADA4522-2/ADA4522-4
VSY = ±2.5V
RL = 10kΩ
CL = 50pF
DUT AV = –1
+1V
0
INPUT
–1V
INPUT
+1V
0
–1V
VSY = ±2.5V
RL = 10kΩ
CL = 50pF
DUT AV = –1
OUTPUT
OUTPUT
+10mV
0
–10mV
+10mV
0
–10mV
TIME (2µs/DIV)
TIME (2µs/DIV)
Figure 69. Positive Settling Time to 0.1%, VSY = ±2.5 V
INPUT VOLTAGE (5V/DIV)
VSY = ±15V AND ±27.5V
RL = 10kΩ
CL = 50pF
DUT AV = –1
0
INPUT
–5V
RL = 10kΩ
AV = –1
50
40
VIN = ±13.5V
VSY = ±15V
20
10
10k
100k
1M
10M
13168-166
VIN = ±1V
VSY = ±2.5V
FREQUENCY (Hz)
TIME (4µs/DIV)
Figure 70. Positive Settling Time to 0.1%, VSY = ±15 V and ±27.5 V
Figure 68. Output Voltage Swing vs. Frequency
Rev. E | Page 20 of 32
13168-049
–50mV
13168-047
–50mV
60
1k
ERROR BAND
POST GAIN = 10
0
Figure 67. Negative Settling Time to 0.1%, VSY = ±15 V and ±27.5 V
0
100
INPUT
–5V
0
TIME (4µs/DIV)
30
0
OUTPUT
ERROR BAND
POST GAIN = 10
VIN = ±26V
VSY = ±27.5V
VSY = ±15V AND ±27.5V
RL = 10kΩ
CL = 50pF
DUT AV = –1
+5V
+50mV
+50mV
OUTPUT
OUTPUT VOLTAGE SWING (V p-p)
INPUT VOLTAGE (5V/DIV)
Figure 66. Negative Settling Time to 0.1%, VSY = ±2.5 V
+5V
13168-048
ERROR BAND
POST GAIN = 10
13168-046
ERROR BAND
POST GAIN = 10
Data Sheet
ADA4522-1/ADA4522-2/ADA4522-4
THEORY OF OPERATION
The ADA4522-1/ADA4522-2/ADA4522-4 are single, dual, and
quad, ultralow noise, high voltage, zero drift, rail-to-rail output
operational amplifiers. They feature a chopping technique that
offers an ultralow input offset voltage of 5 µV and an input
offset voltage drift of 22 nV/°C maximum for theADA4522-1 and
ADA4522-2 and 25 nV/°C maximum for the ADA4522-4. Offset
voltage errors due to common-mode voltage swings and power
supply variations are also corrected by the chopping technique,
resulting in a superb typical CMRR figure of 160 dB and a
PSRR figure of 160 dB at a 30 V supply voltage.
The ADA4522-1/ADA4522-2/ADA4522-4 have wide operating
voltages from ±2.25 V (or 4.5 V) to ±27.5 V (or 55 V). The
devices are single supply amplifiers, where their input voltage
range includes the lower supply rail. They also offer low voltage
noise density of 5.8 nV/√Hz (at f = 1 kHz, AV = 100) and reduced
1/f noise component. These features are ideal for the amplification of low level signals in high precision applications. A few
examples of such applications are weigh scales, high precision
current sensing, high voltage buffers, and signal conditioning
for temperature sensors, among others.
Figure 71 shows the ADA4522-1/ADA4522-2/ADA4522-4
architecture block diagram. The architecture consists of an
input EMI filter and clamp circuitry, three gain stages (Gm1, Gm2,
and Gm3), input and output chopping networks (CHOPIN and
+IN x
CHOPIN
EMI
FILTER
–IN x AND
CLAMP
CHOPOUT), a clock generator, offset and ripple correction loop
circuitry, frequency compensation capacitors (C1, C2, and C3),
and thermal shutdown circuitry.
An EMI filter and clamp circuit is implemented at the input
front end to protect the internal circuitry against electrostatic
discharge (ESD) stresses and high voltage transients. The ability
of the amplifier to reject EMI is explained in detail in the EMI
Rejection Ratio section.
CHOPIN and CHOPOUT are controlled by a clock generator and
operate at 4.8 MHz. The input baseband signal is initially
modulated by CHOPIN. Next, CHOPOUT demodulates the input
signal and modulates the millivolt level input offset voltage and
1/f noise of the input transconductance amplifier, Gm1, to the
chopping frequency at 4.8 MHz. The chopping networks remove
the low frequency errors, but, in return, the networks introduce
chopping artifacts at the chopping frequency. Therefore, a offset
and ripple correction loop, operating at 800 kHz, is used. This
frequency is the switching frequency of the amplifier. This
circuitry reduces chopping artifacts, allowing the ADA4522-1/
ADA4522-2/ADA4522-4 to have a high chopping frequency
with minimal artifacts.
The thermal shutdown circuit shuts down the circuit when
the die is overheated (see the Thermal Shutdown section for
more information).
C1
CHOPOUT
C2
Gm3
Gm2
Gm1
OUT
C3
OFFSET
AND RIPPLE
CORRECTION
LOOP
CLOCK
GENERATOR
THERMAL
SHUTDOWN
4.8MHz CLOCKS
NOTES
1. THE INPUTS ARE +IN x/–IN x ON THE ADA4522-2 AND ADA4522-4,
AND +IN/–IN ON THE ADA4522-1.
2. THE OUTPUT IS OUT ON THE ADA4522-1 AND OUT x ON THE
ADA4522-2 AND ADA4522-4.
Figure 71. ADA4522-1/ADA4522-2/ADA4522-4 Architecture Block Diagram
Rev. E | Page 21 of 32
13168-068
800kHz CLOCKS
ADA4522-1/ADA4522-2/ADA4522-4
Data Sheet
ON-CHIP INPUT EMI FILTER AND CLAMP CIRCUIT
Figure 72 shows the input EMI filter and clamp circuit. The
ADA4522-1/ADA4522-2/ADA4522-4 have internal ESD
protection diodes (D1, D2, D3, and D4) that are connected
between the inputs and each supply rail. These diodes protect
the input transistors in the event of electrostatic discharge and
are reverse biased during normal operation. This protection
scheme allows voltages as high as approximately 300 mV
beyond the rails to be applied at the input of either terminal
without causing permanent damage. See Table 5 in the Absolute
Maximum Ratings section for more information.
The EMI filter is composed of two 200 Ω input series resistors
(RS1 and RS2), two common-mode capacitors (CCM1 and CCM2),
and a differential capacitor (CDM). These RC networks set the
−3 dB low-pass cutoff frequencies at 50 MHz for commonmode signals, and at 33 MHz for differential signals. After the
EMI filter, back to back diodes (D5 and D6) are added to protect
internal circuit devices from high voltage input transients. Each
diode has about 1 V of forward turn on voltage. See the Large
Signal Transient Response section for more information on the
effect of high voltage input transient on the ADA4522-1/
ADA4522-2/ADA4522-4.
As specified in the Absolute Maximum Ratings section (see
Table 5), the maximum input differential voltage is limited to
±5 V. If more than ±5 V is applied, a continuous current larger
than ±10 mA flows through one of the back to back diodes.
This current compromises long-term reliability and can cause
permanent damage to the device.
V+
RS1
200Ω
D1
+IN x
D2
D3
CCM1
–IN x
D4
RS2
C
200Ω DM
D5
D6
PD_PER_AMP = (VSY+ − VSY−) × ISY_PER_AMP + IOUT × (VSY+ − VOUT) (2)
When sinking current, replace (VSY+ − VOUT) in Equation 2 with
(VOUT − VSY−).
Also, take note to include the power dissipation of all channels
of the amplifier when calculating the total power dissipation for
the ADA4522-1/ADA4522-2/ADA4522-4.
The thermal shutdown circuitry does not guarantee the device
to be free of permanent damage if the junction temperature
exceeds 150°C. However, the internal thermal shutdown function
may help avoid permanent damage or reduce the degree of
damage. Each amplifier channel has thermal shutdown circuitry,
composed of a temperature sensor with hysteresis.
As soon as the junction temperature reaches 190°C, the thermal
shutdown circuitry shuts down the amplifier. Note that either
one of the two thermal shutdown circuitries is activated; this
activation disables the channel. When the amplifier is disabled,
the output becomes open state and the quiescent current of the
channel decreases to 0.1 mA. When the junction temperature
cools down to 160°C, the thermal shutdown circuitry enables
the amplifier and the quiescent current increases to its typical
value.
When overheating in the die is caused by an undesirable excess
amount of output current, the thermal shutdown circuit repeats
its function. The junction temperature keeps increasing until it
reaches 190°C and one of the channels is disabled. Then, the
junction temperature cools down until it reaches 160°C, and
the channel is enabled again. The process then repeats.
INPUT PROTECTION
CCM2
13168-069
V–
NOTES
1. THE INPUTS ARE +IN x/–IN x ON THE ADA4522-2
AND ADA4522-4, AND +IN/–IN ON THE ADA4522-1.
The total power dissipation is the sum of quiescent power of the
device and the power required to drive a load for all channels of
an amplifier. The power dissipation per amplifier (PD_PER_AMP)
for sourcing a load is shown in Equation 2.
Figure 72. Input EMI Filter and Clamp Circuit
THERMAL SHUTDOWN
The ADA4522-1/ADA4522-2/ADA4522-4 have internal
thermal shutdown circuitry for each channel of the amplifier. The
thermal shutdown circuitry prevents internal devices from being
damaged by an overheat condition in the die. Overheating can
occur due to a high ambient temperature, a high supply voltage,
and/or high output currents. As specified in Table 5, take care to
maintain the junction temperature below 150°C.
Two conditions affect junction temperature (TJ): the total power
dissipation of the device (PD) and the ambient temperature
surrounding the package (TA). Use the following equation to
estimate the approximate junction temperature:
TJ = PD × θJA + TA
When either input of the ADA4522-1/ADA4522-2/ADA4522-4
exceeds one of the supply rails by more than 300 mV, the ESD
diodes mentioned in the On-Chip Input EMI Filter and Clamp
Circuit section become forward-biased and large amounts of
current begin to flow through them. Without current limiting,
this excessive fault current causes permanent damage to the
device. If the inputs are expected to be subject to overvoltage
conditions, insert a resistor in series with each input to limit the
input current to ±10 mA maximum. However, consider the
resistor thermal noise effect on the entire circuit.
At a ±15 V supply voltage, the broadband voltage noise of the
ADA4522-1/ADA4522-2/ADA4522-4 is approximately
5.8 nV/√Hz (at unity gain), and a 1 kΩ resistor has a thermal
noise of 4 nV/√Hz. Adding a 1 kΩ resistor increases the total
noise to 7 nV/√Hz.
(1)
where θJA is the thermal resistance between the die and the
ambient environment, as shown in Table 6.
Rev. E | Page 22 of 32
Data Sheet
ADA4522-1/ADA4522-2/ADA4522-4
The ADA4522-1/ADA4522-2/ADA4522-4 are single-supply
amplifiers, where their input voltage range includes the lower
supply rail. This feature is ideal for applications where the input
common-mode voltage is at the lower supply rail, for example,
ground sensing. Conversely, the amplifier output is rail to rail.
Figure 73 shows the input and output waveforms of the
ADA4522-1/ADA4522-2/ADA4522-4 configured as a unitygain buffer with a supply voltage of ±15 V. With an input
voltage of ±15 V, the low output voltage tracks the input voltage,
whereas the high output swing clamps/distorts when the input
goes out of the input voltage range (−15 V ≤ IVR ≤ +13.5 V).
However, the device does not exhibit phase reversal.
20
VIN
VSY = ±15V
AV = 1
10
30
VSY = ±27.5V
20
10
0
–20
20
VOUT
10
–20
13168-071
–10
OUTPUT VOLTAGE (V)
–10
0
INPUT VOLTAGE (V)
tial voltage between the input signal and amplifier output possible.
The inverting input voltage then starts slewing with the slew
rate specified in the Specifications section until it reaches its
desired output. Therefore, as seen in Figure 74, there are two
distinctive sections of the rising and falling edge of the output
waveform. With this test condition, the amount and duration of
the input/output current is limited and, therefore, does not
damage the amplifier.
VOLTAGE (V)
SINGLE-SUPPLY AND RAIL-TO-RAIL OUTPUT
–30
TIME (10µs/DIV)
Figure 74. Large Signal Transient Response Example
0
RS_IN–
100Ω
VOUT
LARGE SIGNAL TRANSIENT RESPONSE
VIN = 50V p-p
The noninverting input is driven by an input signal source and
the inverting input is driven by the output of the amplifier. The
maximum amplifier output current depends on the input step
function and the external source resistance at the input
terminals of the amplifier.
Case 1
If the external source resistance is low (for example, 100 Ω in
Figure 75) or if the input step function is large, the maximum
amplifier output current is limited to the output short-circuit
current as specified in the Specifications section. The maximum
differential voltage between the input signal and the amplifier
output is then limited by the maximum amplifier output current
multiplied by the total input resistance (internal and external)
and the turn-on voltage of the back to back diode (see Figure 72
for the input EMI filter and clamp circuit architecture).
ADA4522-1/
ADA4522-2/
ADA4522-4
100pF
RS_IN+
100Ω VSY–
Figure 73. Input and Output Waveforms, No Phase Reversal
When the ADA4522-1/ADA4522-2/ADA4522-4 are configured
in a closed-loop configuration with a large input transient (for
example, a step input voltage), the internal back to back diodes may
turn on. Consider a case where the amplifier is in unity-gain
configuration with a step input waveform. This case is shown in
Figure 74.
VSY+
10kΩ
13168-100
–20
TIME (400s/DIV)
13168-070
–10
Figure 75. Circuit Diagram for Large Signal Transient Response
Case 2
If the external source resistance is high or if the input step function
is small, the maximum output current is limited to the instantaneous difference between the input signal and amplifier output
voltage (which is the change in the step function) divided by the
source resistance. This maximum output current is less than the
amplifier output short-circuit current. The maximum differential
voltage between the input signal and the amplifier output is
then equal to the step function. The output voltage slews until it
reaches its desired output.
Therefore, if desired, reduce the input current by adding a larger
external resistor between the signal source and the noninverting
input. Similarly, to reduce output current, add an external resistor
to the feedback loop between the inverting input and output. This
large signal transient response issue is typically not a problem
when the amplifier is configured in closed-loop gain, where the
input signal source is usually much smaller and the gain and
feedback resistors limit the current.
Back to back diodes are also implemented in many other
amplifiers; these amplifiers show similar slewing behavior.
When the noninverting input voltage changes with a step signal,
the inverting input voltage (and, therefore, the output voltage)
follows the change quickly until it reaches the maximum differenRev. E | Page 23 of 32
ADA4522-1/ADA4522-2/ADA4522-4
Data Sheet
NOISE CONSIDERATIONS
Residual Ripple
1/f Noise
As shown in Figure 60, Figure 61, and Figure 62, the ADA4522-1/
ADA4522-2/ADA4522-4 have a flat noise spectrum density at
lower frequencies and exhibits spectrum density bumps and peaks
at higher frequencies.
The ADA4522-1/ADA4522-2/ADA4522-4 are some of the
lowest noise high voltage zero drift amplifiers with 5.8 nV/√Hz
of voltage noise density at 1 kHz (AV = 100). Therefore, it is
important to consider the input source resistance of choice to
maintain a total low noise. The total input referred broadband
noise (eN total) from any amplifier is primarily a function of
three types of noise: input voltage noise, input current noise,
and thermal (Johnson) noise from the external resistors.
These uncorrelated noise sources can be summed up in a root
sum squared (rss) manner by using the following equation:
eN total = (eN2 + 4 kTRS + (iN × RS)2)1/2
where:
eN is the input voltage noise density of the amplifier (V/√Hz).
k is Boltzmann’s constant (1.38 × 10−23 J/K).
T is the temperature in Kelvin (K).
RS is the total input source resistance (Ω).
iN is the input current noise density of the amplifier (A/√Hz).
The total equivalent rms noise over a specific bandwidth is
expressed as
eN RMS = eN total BW
where BW is the bandwidth in hertz.
This analysis is valid for broadband noise calculation up to a
decade before the switching frequency. If the bandwidth of
concern includes the switching frequency, more complicated
calculations must be made to include the effect of the increase
in noise at the switching frequency.
The offset and ripple correction loop, designed to reduce the
4.8 MHz switching artifact, also creates a noise bump centered
at 800 kHz and a noise peak on top of this noise bump. Although
the magnitude of the bump is mostly constant, the magnitude of
the 800 kHz peak is different from unit to unit. Some units may
not exhibit the 800 kHz noise peak; however, for other units,
peaks occur at multiple integrals of 800 kHz, such as 1.6 MHz or
2.4 MHz.
These noise peaks, albeit small in magnitude, can be significant
when the amplifier has a closed-loop frequency that is higher
than the chopping frequency. To suppress the noise spike to a
desired level, either configure the amplifier in a high gain
configuration or apply a post filter at the output of the amplifier.
Figure 76 shows the voltage noise density of the ADA4522-1/
ADA4522-2/ADA4522-4 in various gain configurations. Note that
the higher the gain, the lower the available bandwidth is. The
earlier bandwidth roll-off effectively filters out the higher noise
spectrum.
100
With a low source resistance of RS < 1 kΩ, the voltage noise of
the amplifier dominates. As the source resistance increases, the
thermal noise of RS dominates. As the source resistance further
increases, where RS > 50 kΩ, the current noise becomes the
main contributor of the total input noise.
Rev. E | Page 24 of 32
VSY = ±15V
AV = 1
10
AV = 10
AV = 100
1
100
1k
10k
100k
1M
10M
FREQUENCY (Hz)
Figure 76. Voltage Noise Density with Various Gains
100M
13168-072
Source Resistance
The largest noise bump is centered at 6 MHz; this bump is due
to the decrease in the input gain at higher frequencies. This
decrease is a typical phenomenon and can also be seen in other
amplifiers. In addition to the noise bump, a sharp peak due to the
chopping networks is seen at 4.8 MHz. However, this magnitude is
significantly reduced by the offset and ripple correction loop. Its
magnitude may be different with different amplifier units or with
different circuitries around the amplifier. This peak can potentially
be hidden by the noise bump and, therefore, may not be detected.
VOLTAGE NOISE DENSITY (nV/√Hz)
1/f noise, also known as pink noise or flicker noise, is inherent
in semiconductor devices and increases as frequency decreases.
At a low frequency, 1/f noise is a major noise contributor and
causes a significant output voltage offset when amplified by the
noise gain of the circuit. However, because the low frequency
1/f noise appears as a slow varying offset to the ADA4522-1/
ADA4522-2/ADA4522-4, it is effectively reduced by the chopping
technique. This technique allows the ADA4522-1/ADA4522-2/
ADA4522-4 to have a much lower noise at dc and low frequency in
comparison to standard low noise amplifiers that are susceptible
to 1/f noise. Figure 64 shows the 0.1 Hz to 10 Hz noise to be only
117 nV p-p of noise.
Data Sheet
ADA4522-1/ADA4522-2/ADA4522-4
Figure 77 shows the voltage noise density of the ADA4522-1/
ADA4522-2/ADA4522-4 without and with post filters at different
frequencies. The post filter serves to roll off the bandwidth
before the switching frequency. In this example, the noise peak
at 800 kHz is about 38 nV/√Hz. With a post filter at 80 kHz, the
noise peak is reduced to 4.1 nV/√Hz. With a post filter at 8 kHz,
the noise peak is lower than the noise floor and cannot be detected.
AV = 1
AV = 1 (POST FILTER AT 80kHz)
AV = 1 (POST FILTER AT 8kHz)
100k
1M
10M
100M
FREQUENCY (Hz)
Figure 77. Voltage Noise Density with Post Filters
Current Noise Density
Figure 78 shows the current noise density of the ADA4522-1/
ADA4522-2/ADA4522-4 at unity gain. At 1 kHz, the current
noise density is about 1.3 pA/√Hz. The current noise density is
determined by measuring the voltage noise due to current noise
flowing through a resistor. Due to the low current noise density
of the amplifier, the voltage noise is usually measured with a
high value resistor; in this case, a 100 kΩ source resistor is used.
However, the source resistor interacts with the input capacitance of the amplifier and board, causing the bandwidth to roll
off. Note that Figure 78 shows the current noise density rolling
off much earlier than the unity-gain bandwidth; this roll-off is
expected.
100
VIN = 100mV p-p
90
80
70
60
50
40
30
20
VSY = ±2.5V
VSY = ±15V
VSY = ±27.5V
55V
30V
5V
10
0
10M
100M
1G
FREQUENCY (Hz)
10G
Figure 79. EMIRR vs. Frequency
CAPACITIVE LOAD STABILITY
1
0.1
10
100
1k
10k
FREQUENCY (Hz)
Figure 78. Current Noise Density at Gain = 1
100k
13168-074
CURRENT NOISE DENSITY (pA/√Hz)
RS = 100kΩ
AV = 1
EMIRR = 20log(VIN_PEAK/ΔVOS)
13168-075
10k
The ADA4522-1/ADA4522-2/ADA4522-4 have integrated EMI
filters at their input stage. To describe the ability of the
ADA4522-1/ADA4522-2/ADA4522-4 to perform as intended
in the presence of electromagnetic energy, the electromagnetic
interference rejection ratio (EMIRR) of the noninverting pin is
specified in Table 2, Table 3, and Table 4 of the Specifications
section. A mathematical method of measuring EMIRR is
defined as follows:
EMIRR (dB)
1
1k
10
Circuit performance is often adversely affected by high frequency EMI. When the signal strength is low and transmission
lines are long, an op amp must accurately amplify the input
signals. However, all op amp pins—the noninverting input,
inverting input, positive supply, negative supply, and output
pins—are susceptible to EMI signals. These high frequency
signals are coupled into an op amp by various means, such as
conduction, near field radiation, or far field radiation. For example,
wires and printed circuit board (PCB) traces can act as antennas
and pick up high frequency EMI signals.
Amplifiers do not amplify EMI or RF signals due to their relatively low bandwidth. However, due to the nonlinearities of the
input devices, op amps can rectify these out of band signals. When
these high frequency signals are rectified, they appear as a dc
offset at the output.
10
13168-073
VOLTAGE NOISE DENSITY (nV/√Hz)
100
EMI REJECTION RATIO
The ADA4522-1/ADA4522-2/ADA4522-4 can safely drive capacitive loads of up to 250 pF in any configuration. As with most
amplifiers, driving larger capacitive loads than specified may cause
excessive overshoot and ringing, or even oscillation. A heavy
capacitive load reduces the phase margin and causes the amplifier
frequency response to peak. Peaking corresponds to overshooting
or ringing in the time domain. Therefore, it is recommended that
external compensation be used if the ADA4522-1/ADA4522-2/
ADA4522-4 must drive a load exceeding 250 pF. This compensation is particularly important in the unity-gain configuration,
which is the worst case for stability.
Rev. E | Page 25 of 32
ADA4522-1/ADA4522-2/ADA4522-4
Data Sheet
+VSY
–VSY
45
35
30
25
20
15
VOUT
ADA4522-1/
ADA4522-2/
ADA4522-4
40
10
CL
5
0
10
Figure 80. Stability Compensation with Isolating Resistor, RISO
100
LOAD CAPACITANCE (pF)
Figure 81 shows the effect on overshoot with different values of
RISO.
1k
13168-077
VIN
OS+ (RISO = 0Ω)
OS– (RISO = 0Ω)
OS+ (RISO = 25Ω)
OS– (RISO = 25Ω)
OS+ (RISO = 50Ω)
OS– (RISO = 50Ω)
VSY = ±15V
55 RL = 10kΩ
AV = 1
50 V = 100mV p-p
IN
13168-076
RISO
60
OVERSHOOT (%)
A quick and easy way to stabilize the op amp for capacitive load
drive is by adding a series resistor, RISO, between the amplifier
output terminal and the load capacitance, as shown in Figure 80.
RISO isolates the amplifier output and feedback network from
the capacitive load. However, with this compensation scheme,
the output impedance as seen by the load increases, and this
reduces gain accuracy.
Figure 81. Small Signal Overshoot vs. Load Capacitance with Various Output
Isolating Resistors
Rev. E | Page 26 of 32
Data Sheet
ADA4522-1/ADA4522-2/ADA4522-4
APPLICATIONS INFORMATION
SINGLE-SUPPLY INSTRUMENTATION AMPLIFIER
The extremely low offset voltage and drift, high open-loop gain,
high common-mode rejection, and high power supply rejection of
the ADA4522-1/ADA4522-2/ADA4522-4 make them excellent op
amp choices as discrete, single-supply instrumentation amplifiers.
Figure 82 shows the classic 3-op-amp instrumentation amplifier
using the ADA4522-1/ADA4522-2/ADA4522-4. The key to high
CMRR for the instrumentation amplifier are resistors that are well
matched for both the resistive ratio and relative drift. For true
difference amplification, matching of the resistor ratio is very
important, where R5/R2 = R6/R4. The resistors are important
in determining the performance over manufacturing tolerances,
time, and temperature. Assuming a perfect unity-gain difference
amplifier with infinite common-mode rejection, a 1% tolerance
resistor matching results in only 34 dB of common-mode rejection.
Therefore, at least 0.01% or better resistors are recommended.
A1
R5
RG1
RG2
R3
A2
VOUT
R4
R6
13168-078
VIN2
RG1 = RG2, R1 = R3, R2 = R4, R5 = R6
VOUT = (VIN2 – VIN1) (1 + R1/RG1) (R5/R2)
Figure 82. Discrete 3-Op-Amp Instrumentation Amplifier
To build a discrete instrumentation amplifier with external resistors without compromising on noise, pay close attention to the
resistor values chosen. RG1 and RG2 each have thermal noise that
is amplified by the total noise gain of the instrumentation amplifier
and, therefore, a sufficiently low value must be chosen to reduce
thermal noise contribution at the output while still providing an
accurate measurement. Table 10 shows the external resistors noise
contribution referred to the output (RTO).
Table 10. Thermal Noise Contribution Example
Resistor
RG1
RG2
R1
R2
R3
R4
R5
R6
Value
(kΩ)
0.4
0.4
10
10
10
10
20
20
Resistor Thermal
Noise (nV/√Hz)
2.57
2.57
12.83
12.83
12.83
12.83
18.14
18.14
Understanding how noise impacts a discrete instrumentation
amplifier or a difference amplifier (the second stage of a 3-opamp instrumentation amplifier) is important, because they are
commonly used in many different applications. The Load
Cell/Strain Gage Sensor Signal Conditioning section and the
Precision Low-Side Current Shunt Sensor section show the
ADA4522-1/ADA4522-2/ADA4522-4 used as a discrete
instrumentation or difference amplifier in an application.
The ADA4522-2, with its ultralow offset, drift, and noise, is well
suited to signal condition a low level sensor output with high gain
and accuracy. A weigh scale/load cell is an example of an
application with such requirements. Figure 83 shows a configuration for a single-supply, precision, weigh scale measurement
system. The ADA4522-2 is used at the front end for amplification
of the low level signal from the load cell.
R2
A3
Any unused channel of the ADA4522-1/ADA4522-2/
ADA4522-4 must be configured in unity gain with the input
common-mode voltage tied to the midpoint of the power
supplies.
LOAD CELL/STRAIN GAGE SENSOR SIGNAL
CONDITIONING USING THE ADA4522-2
VIN1
R1
overall instrumentation amplifier input, is divided by the first
stage gain and is not as important. Note that the input offset
voltage and the input voltage noise of the amplifiers are also
amplified by the overall noise gain.
Thermal Noise
RTO (nV/√Hz)
128.30
128.30
25.66
25.66
25.66
25.66
18.14
18.14
Note that A1 and A2 have a high gain of 1 + R1/RG1. Therefore,
use a high precision, low offset voltage and low noise amplifier
for A1 and A2, such as the ADA4522-1/ADA4522-2/ADA4522-4.
Conversely, A3 operates at a much lower gain and has a different set of op amp requirements. Its input noise, referred to the
Current flowing through a PCB trace produces an IR voltage
drop; with longer traces, this voltage drop can be several
millivolts or more, introducing a considerable error. A 1 inch
long, 0.005 inch wide trace of 1 oz copper has a resistance of
approximately 100 mΩ at room temperature. With a load
current of 10 mA, the resistance can introduce a 1 mV error.
Therefore, a 6-wire load cell is used in the circuit. The load cell
has two sense pins, in addition to excitation, ground, and two
output connections. The sense pins are connected to the high
side (excitation pin) and low side (ground pin) of the
Wheatstone bridge. The voltage across the bridge can then be
accurately measured regardless of voltage drop due to wire
resistance. The two sense pins are also connected to the analogto-digital converter (ADC) reference inputs for a ratiometric
configuration that is immune to low frequency changes in the
power supply excitation voltage.
The ADA4522-2 is configured as the first stage of a 3-op-amp
instrumentation amplifier to amplify the low level amplitude
signal from the load cell by a factor of 1 + 2R1/RG. Capacitors
C1 and C2 are placed in the feedback loops of the amplifiers
and interact with R1 and R2 to perform low-pass filtering. This
filtering limits the amount of noise entering the Σ-Δ ADC. In
addition, C3, C4, C5, R3, and R4 provide further common-mode
and differential mode filtering to reduce noise and unwanted
signals.
Rev. E | Page 27 of 32
ADA4522-1/ADA4522-2/ADA4522-4
Data Sheet
+5V
V+
1/2
1µF
R1 11.3kΩ
RG
60.4Ω
VEXC
OUT–
SENSE+
C1 3.3µF
R4
1kΩ
C2 3.3µF
OUT+
SENSE–
R3
1kΩ
VDD
REF(+)
REF(–)
100pF
C3
1µF
DIN
DOUT/
RDY
AD7791
AIN(+)
SCLK
C5
10µF
CS
AIN(–)
C4
1µF
GND
R2 11.3kΩ
1/2
13168-079
LOAD
CELL
100pF
ADA4522-2
ADA4522-2
Figure 83. Precision Weigh Scale Measurement System
PRECISION LOW-SIDE CURRENT SHUNT SENSOR
A typical shunt may be 100 mΩ. At a measured current of 1 A,
the voltage produced from the shunt is 100 mV, and the amplifier error sources are not critical. However, at low measured current
in the 1 mA range, the 100 μV generated across the shunt demands
a very low offset voltage and drift amplifier to maintain absolute
accuracy. The unique attributes of a zero drift amplifier provide
a solution. Figure 84 shows a low-side current sensing circuit
using the ADA4522-1/ADA4522-2/ADA4522-4. The ADA4522-1/
ADA4522-2/ADA4522-4 are configured as difference amplifiers
with a gain of 1000. Although the ADA4522-1/ADA4522-2/
ADA4522-4 have high CMRR, the CMRR of the system is
limited by the external resistors. Therefore, as mentioned in the
Single-Supply Instrumentation Amplifier section, the key to
high CMRR for the system is resistors that are well matched
from both the resistive ratio and relative drift, where R1/R2 =
R3/R4.
Any unused channel of the ADA4522-1/ADA4522-2/
ADA4522-4 must be configured in unity gain with the input
common-mode voltage tied to the midpoint of the power
supplies.
VSY
VOUT*
RS
0.1Ω
I
R1
100Ω
R2
100kΩ
ADA4522-1/
ADA4522-2/
ADA4522-4
R4
100kΩ
RL
VSY
R3
100Ω
*VOUT = AMPLIFIER GAIN × VOLTAGE ACROSS RS
= 1000 × RS × I
= 100 × I
13168-080
Many applications require the sensing of signals near the
positive or negative rails. Current shunt sensors are one such
application and are mostly used for feedback control systems.
They are also used in a variety of other applications, including
power metering, battery fuel gauging, and feedback controls in
industrial applications. In such applications, it is desirable to
use a shunt with very low resistance to minimize series voltage
drop. This configuration not only minimizes wasted power, but
also allows the measurement of high currents while saving power.
I
Figure 84. Low-Side Current Sensing Circuit
PRINTED CIRCUIT BOARD LAYOUT
The ADA4522-1/ADA4522-2/ADA4522-4 are high precision
devices with ultralow offset voltage and noise. Therefore, take
care in the design of the PCB layout to achieve optimum
performance of the ADA4522-1/ADA4522-2/ADA4522-4 at the
board level.
To avoid leakage currents, keep the surface of the board clean
and free of moisture.
Properly bypassing the power supplies and keeping the supply
traces short minimizes power supply disturbances caused by
output current variation. Connect bypass capacitors as close
as possible to the device supply pins. Stray capacitances are a
concern at the outputs and the inputs of the amplifier. It is
recommended that signal traces be kept at a distance of at
least 5 mm from supply lines to minimize coupling.
A potential source of offset error is the Seebeck voltage on the
circuit board. The Seebeck voltage occurs at the junction of two
dissimilar metals and is a function of the temperature of the
junction. The most common metallic junctions on a circuit board
are solder to board traces and solder to component leads. Figure 85
shows a cross section of a surface-mount component soldered
to a PCB. A variation in temperature across the board (where TA1 ≠
TA2) causes a mismatch in the Seebeck voltages at the solder joints,
thereby resulting in thermal voltage errors that degrade the
Rev. E | Page 28 of 32
Data Sheet
ADA4522-1/ADA4522-2/ADA4522-4
however, these diodes also allow a current path from the input
to the lower supply rail, resulting in an increase in the total
supply current of the system. Both comparator configurations yield
the same result. At 30 V of power supply, ISY+ remains at 1.55 mA
per dual amplifier, but ISY− increases close to 2 mA in magnitude per dual amplifier.
performance of the ultralow offset voltage of the ADA4522-1/
ADA4522-2/ADA4522-4.
COMPONENT
LEAD
VSC1 +
SURFACE-MOUNT
COMPONENT
+
VTS1 +
VSC2
SOLDER
+ VTS2
+VSY
PC BOARD
A1
10kΩ
ISY+
ADA4522-1/
ADA4522-2/
ADA4522-4
Figure 85. Mismatch in Seebeck Voltages Causes Seebeck Voltage Error
VOUT
In Figure 85, VSC1 and VSC2 are the Seebeck voltages due to solder to
component at Junction 1 and Junction 2, respectively. VTS1 and
VTS2 are the Seebeck voltages due to solder to trace at Junction 1
and Junction 2. TA1 and TA2 are the temperatures of Junction 1
and Junction 2, respectively.
10kΩ
–VSY
To minimize these thermocouple effects, orient resistors so
that heat sources warm both ends equally. Where possible, it
is recommended that the input signal paths contain matching
numbers and types of components to match the number and type
of thermocouple junctions. For example, dummy components,
such as zero value resistors, can be used to match the thermoelectric error source (real resistors in the opposite input path).
Place matching components in close proximity and orient them
in the same manner to ensure equal Seebeck voltages, thus
cancelling thermal errors. Additionally, use leads that are of
equal length to keep thermal conduction in equilibrium. Keep
heat sources on the PCB as far away from amplifier input circuitry
as is practical.
Figure 86. Comparator Configuration A
+VSY
A1
VOUT
10kΩ
ISY–
–VSY
2.2
2.0
ISY–
1.8
1.6
ISY+
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
0
2
4
6
8
10 12 14 16 18 20 22 24 26 28 30
VSY (V)
13168-084
Figure 86 and Figure 87 show the ADA4522-1/ADA4522-2/
ADA4522-4 configured as a comparator, with 10 kΩ resistors in
series with the input pins. Any unused channels are configured as
buffers with the input voltage kept at the midpoint of the power
supplies. The ADA4522-1/ADA4522-2/ADA4522-4 have input
devices that are protected from large differential input voltages by
Diode D5 and Diode D6, as shown in Figure 72. These diodes
consist of substrate PNP bipolar transistors, and conduct whenever
the differential input voltage exceeds approximately 600 mV;
A2
Figure 87. Comparator Configuration B
ISY PER DUAL AMPLIFIER (mA)
An op amp is designed to operate in a closed-loop configuration
with feedback from its output to its inverting input. In contrast to
op amps, comparators are designed to operate in an open-loop
configuration and to drive logic circuits. Although op amps are
different from comparators, occasionally an unused section of a
dual op amp is used as a comparator to save board space and
cost; however, this is not recommended for the ADA4522-1/
ADA4522-2/ADA4522-4.
ISY+
ADA4522-1/
ADA4522-2/
ADA4522-4
10kΩ
It is highly recommended to use a ground plane. A ground
plane helps distribute heat throughout the board, maintain a
constant temperature across the board, and reduce EMI noise
pickup.
COMPARATOR OPERATION
ISY–
A2
13168-082
IF TA1 ≠ TA2, THEN
VTS1 + VSC1 ≠ VTS2 + VSC2
13168-083
TA2
13168-081
TA1
COPPER
TRACE
Figure 88. Supply Current (ISY) per Dual Amplifier vs. Supply Voltage (VSY)
(ADA4522-1/ADA4522-2/ADA4522-4 as a Comparator)
Note that 10 kΩ resistors are used in series with the input of the
op amp. If smaller resistor values are used, the supply current of the
system increases much more. For more details on op amps as
comparators, see the AN-849 Application Note, Using Op Amps
as Comparators.
Rev. E | Page 29 of 32
ADA4522-1/ADA4522-2/ADA4522-4
Data Sheet
OUTLINE DIMENSIONS
3.20
3.00
2.80
8
3.20
3.00
2.80
5.15
4.90
4.65
5
1
4
PIN 1
IDENTIFIER
0.65 BSC
0.95
0.85
0.75
15° MAX
1.10 MAX
0.80
0.55
0.40
0.23
0.09
6°
0°
0.40
0.25
10-07-2009-B
0.15
0.05
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-187-AA
Figure 89. 8-Lead Mini Small Outline Package [MSOP]
(RM-8)
Dimensions shown in millimeters
5.00 (0.1968)
4.80 (0.1890)
1
5
6.20 (0.2441)
5.80 (0.2284)
4
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
COPLANARITY
0.10
SEATING
PLANE
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
0.31 (0.0122)
0.50 (0.0196)
0.25 (0.0099)
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-012-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 90. 8-Lead Small Outline Package [SOIC_N]
Narrow Body
(R-8)
Dimensions shown in millimeters and (inches)
Rev. E | Page 30 of 32
012407-A
8
4.00 (0.1574)
3.80 (0.1497)
Data Sheet
ADA4522-1/ADA4522-2/ADA4522-4
8.75 (0.3445)
8.55 (0.3366)
4.00 (0.1575)
3.80 (0.1496)
8
14
1
7
6.20 (0.2441)
5.80 (0.2283)
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0039)
COPLANARITY
0.10
0.50 (0.0197)
0.25 (0.0098)
1.75 (0.0689)
1.35 (0.0531)
SEATING
PLANE
0.51 (0.0201)
0.31 (0.0122)
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
060606-A
COMPLIANT TO JEDEC STANDARDS MS-012-AB
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 91. 14-Lead Small Outline Package [SOIC_N]
Narrow Body
(R-14)
Dimensions shown in millimeters and (inches)
5.10
5.00
4.90
14
8
4.50
4.40
4.30
6.40
BSC
1
7
PIN 1
0.65 BSC
1.20
MAX
0.15
0.05
COPLANARITY
0.10
0.30
0.19
0.20
0.09
SEATING
PLANE
8°
0°
COMPLIANT TO JEDEC STANDARDS MO-153-AB-1
Figure 92. 14-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-14)
Dimensions shown in millimeters
Rev. E | Page 31 of 32
0.75
0.60
0.45
061908-A
1.05
1.00
0.80
ADA4522-1/ADA4522-2/ADA4522-4
Data Sheet
ORDERING GUIDE
Model1
ADA4522-1ARMZ
ADA4522-1ARMZ-R7
ADA4522-1ARMZ-RL
ADA4522-1ARZ
ADA4522-1ARZ-R7
ADA4522-1ARZ-RL
ADA4522-2ARMZ
ADA4522-2ARMZ-R7
ADA4522-2ARMZ-RL
ADA4522-2ARZ
ADA4522-2ARZ-R7
ADA4522-2ARZ-RL
ADA4522-4ARUZ
ADA4522-4ARUZ-R7
ADA4522-4ARUZ-RL
ADA4522-4ARZ
ADA4522-4ARZ-R7
ADA4522-4ARZ-RL
1
Temperature Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Package Description
8-Lead Mini Small Outline Package [MSOP]
8-Lead Mini Small Outline Package [MSOP]
8-Lead Mini Small Outline Package [MSOP]
8-Lead Small Outline Package [SOIC_N]
8-Lead Small Outline Package [SOIC_N]
8-Lead Small Outline Package [SOIC_N]
8-Lead Mini Small Outline Package [MSOP]
8-Lead Mini Small Outline Package [MSOP]
8-Lead Mini Small Outline Package [MSOP]
8-Lead Small Outline Package [SOIC_N]
8-Lead Small Outline Package [SOIC_N]
8-Lead Small Outline Package [SOIC_N]
14-Lead Thin Shrink Small Outline Package [TSSOP]
14-Lead Thin Shrink Small Outline Package [TSSOP]
14-Lead Thin Shrink Small Outline Package [TSSOP]
14-Lead Standard Small Outline Package [SOIC_N]
14-Lead Standard Small Outline Package [SOIC_N]
14-Lead Standard Small Outline Package [SOIC_N]
Z = RoHS Compliant Part.
©2015–2016 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D13168-0-10/16(E)
Rev. E | Page 32 of 32
Package Option
RM-8
RM-8
RM-8
R-8
R-8
R-8
RM-8
RM-8
RM-8
R-8
R-8
R-8
RU-14
RU-14
RU-14
R-14
R-14
R-14
Branding
A3G
A3G
A3G
A39
A39
A39
Similar pages