ON NB3L202KMNG Differential 1:2 hcsl fanout buffer Datasheet

NB3L202K
2.5 V, 3.3 V Differential 1:2
HCSL Fanout Buffer
Description
The NB3L202K is a differential 1:2 Clock fanout buffer with
High−speed Current Steering Logic (HCSL) outputs. Inputs can
directly accept differential LVPECL, LVDS, and HCSL signals.
Single−ended LVPECL, HCSL, LVCMOS, or LVTTL levels are
accepted with a proper external Vth reference supply per Figures 4
and 6. The input signal will be translated to HCSL and provides two
identical copies operating up to 350 MHz.
The NB3L202K is optimized for ultra−low phase noise, propagation
delay variation and low output–to–output skew, and is DB200H
compliant. As such, system designers can take advantage of the
NB3L202K’s performance to distribute low skew clocks across the
backplane or the motherboard making it ideal for Clock and Data
distribution applications such as PCI Express, FBDIMM, Networking,
Mobile Computing, Gigabit Ethernet, etc.
Output drive current is set by connecting a 475 W resistor from
IREF (Pin 10) to GND per Figure 11. Outputs can also interface to
LVDS receivers when terminated per Figure 12.
www.onsemi.com
MARKING
DIAGRAM
1
1
QFN16
3x3
CASE 485AE
NB3L
202K
ALYWG
G
NB3L202K = Specific Device Code
A
= Assembly Location
L
= Wafer Lot
Y
= Year
W
= Work Week
G
= Pb−Free Package
(Note: Microdot may be in either location)
Features
•
•
•
•
•
•
•
•
•
•
•
•
Maximum Input Clock Frequency > 350 MHz
2.5 V ±5% / 3.3 V ±10% Supply Voltage Operation
2 HCSL Outputs
DB200H Compliant
Individual OE Control Pin for Each Output
100 ps Max Output−to−Output Skew Performance
1 ns Typical Propagation Delay
500 ps Typical Rise and Fall Times
80 fs Maximum Additive RMS Phase Jitter
−40°C to +85°C Ambient Operating Temperature
QFN 16−pin Package, 3 mm x 3 mm
These Devices are Pb−Free and are RoHS Compliant
ORDERING INFORMATION
See detailed ordering and shipping information page 13 of this
data sheet.
Typical Applications
•
•
•
•
•
PCI Express
FBDIMM
Mobile Computing
Networking
Gigabit Ethernet
© Semiconductor Components Industries, LLC, 2016
April, 2016 − Rev. 0
1
Publication Order Number:
NB3L202K/D
NB3L202K
Figure 1. Simplified Block Diagram
Figure 2. 16−Pin QFN Pinout
(Top View)
www.onsemi.com
2
NB3L202K
Table 1. PIN DESCRIPTION
Pin Number
Pin Name
I/O
1
GND
Power
Ground
Description
2
CLK_IN
I, DIF
Differential True input
3
CLK_IN#
I, DIF
Differential Complementary input
4
VDD
Power
Core power supply
5
GND_O
Power
Ground for outputs
6
DIF_1#
O, DIF
0.7 V Differential Complementary Output
7
DIF_1
O, DIF
0.7 V Differential True Output
8
VDD_O
Power
Power supply for outputs
9
GND
Power
Ground
10
IREF
I
11
OE0#
I, SE
LVTTL / LVCMOS active low input for enabling output DIF_0/0#. 0 enables outputs,
1 disables outputs. Internal pull down.
12
OE1#
I, SE
LVTTL / LVCMOS active low input for enabling output DIF_1/1#. 0 enables outputs,
1 disables outputs. Internal pull down.
13
VDD_O
Power
Power supply for outputs
14
DIF_0
O, DIF
0.7 V Differential True Output
15
DIF_0#
O, DIF
0.7 V Differential Complementary Output
16
GND_O
Power
Ground for outputs
EP
Exposed
Pad
Thermal
A precision resistor is attached to this pin to set the differential output current.
Use RREF = 475 W, 1% for 100 W trace, with 50 W termination.
Use RREF = 412 W, 1% for 85 W trace, with 43 W termination.
The Exposed Pad (EP) on the QFN16 package bottom is thermally connected to the die
for improved heat transfer out of package. The exposed pad must be attached to a
heat−sinking conduit. The pad is electrically connected to the die, and must be electrically and thermally connected to GND on the PC board.
www.onsemi.com
3
NB3L202K
Table 2. ATTRIBUTES
Characteristics
ESD Protection
Value
Human Body Model
> 2000 V
RPD − Pull−down Resistor
50 kW
Moisture Sensitivity (Note 1)
Level 1
Flammability Rating
Oxygen Index: 28 to 34
UL 94 V−0 @ 0.125 in
Transistor Count
1344
Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test
1. For additional information, see Application Note AND8003/D.
Table 3. ABSOLUTE MAXIMUM RATINGS
Symbol
VDD
VDD_O
Parameter
Min
Max
Unit
Core Supply Voltage
−
4.6
V
I/O Supply Voltage
−
4.6
V
VIH
Input High Voltage (Note 2)
VIL
Input Low Voltage
IOUT
Maximum Output Current
−
4.6
V
−0.5
−
V
−
24
mA
TA
Operating Temperature Range
−40 to +85
°C
Tstg
Storage Temperature Range
−65 to +150
°C
qJA
Thermal Resistance (Junction−to−Ambient) (Note 3)
qJC
Thermal Resistance (Junction−to−Case) (Note 3)
Tsol
Wave Solder
0 lfpm
500 lfpm
42
35
°C/W
4
°C/W
265
°C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
2. Maximum VIH is not to exceed maximum VDD.
3. JEDEC standard multilayer board − 2S2P (2 signal, 2 power) with 8 filled thermal vias under exposed pad.
www.onsemi.com
4
NB3L202K
Table 4. DC CHARACTERISTICS VDD = VDD_O = 3.3 V ±10% or 2.5 V ±5%, TA = −40°C to 85°C
Symbol
Characteristics
Min
Typ
Max
Unit
VDD = 3.3 V ±10%
VDD = 2.5 V ±5%
2.970
2.375
3.3
2.5
3.630
2.625
V
VDD_O = 3.3 V ±10%
VDD_O = 2.5 V ±5%
2.970
2.375
3.3
2.5
3.630
2.625
V
80
110
mA
POWER SUPPLY CURRENT
VDD
VDD_O
Core Power Supply Voltage
Output Power Supply Voltage
IDD + IDD_O Total Power Supply Current (all outputs active @ 350 MHz, RREF = 412 W,
RL = 43 W)
Istdby
Standby Current, all OE pins de−asserted with inputs @ 350 MHz
50
65
mA
lincr
Incremental output current for additional output; One OE Enabled
15
23
mA
Istdby + lincr Standby Current plus incremental current for one additional differential output;
One OE Enabled @ 350 MHz
65
88
mA
850
mV
HCSL OUTPUTS (Notes 4, 5)
VOH
Output HIGH Voltage
660
VOL
Output LOW Voltage
−150
Output Swing (Single−Ended)
Output Swing (Differential)
400
800
VOUT
mV
750
1500
mV
DIFFERENTIAL INPUT DRIVEN SINGLE−ENDED (Note 6) (Figures 4 and 6)
VIH
CLK_IN/CLK_IN# Single-ended Input HIGH Voltage
0.5
VDD
V
VIL
CLK_IN/CLK_IN# Single-ended Input LOW Voltage
GND
VIH − 0.3
V
Vth
Input Threshold Reference Voltage Range (Note 7)
0.25
VDD − 1.0
V
Single-ended Input Voltage (VIH − VIL)
0.5
VDD
V
VISE
DIFFERENTIAL INPUTS DRIVEN DIFFERENTIALLY (Note 8) (Figures 5 and 7)
VIHD
Differential Input HIGH Voltage
0.5
VDD − 0.85
V
VILD
Differential Input LOW Voltage
0
VIHD −
0.25
V
VID
Differential Input Voltage (VIHD − VILD)
0.25
1.3
V
Input Common Mode Range (Differential Configuration) (Note 9) (Figure 8)
0.5
VDD − 0.85
V
Input Leakage Current 0 < VIN < VDD (Note 10)
−5
5
mA
VIHCMR
IIL
LVTTL / LVCMOS INPUTS (OEx#)
VIH
Input HIGH Voltage
2.0
VDD + 0.3
V
VIL
Input LOW Voltage
−0.3
0.8
V
IIL
Input LOW Current (VIN = GND)
−10
+10
mA
IIH
Input HIGH Current (VIN = VDD)
100
mA
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
4. Test configuration is RS = 33.2 W, RL = 49.9, CL = 2 pF, RREF = 475 W.
5. Measurement taken from Single−Ended waveform unless specified otherwise.
6. VIH, VIL, Vth and VISE parameters must be complied with simultaneously.
7. Vth is applied to the complementary input when operating in single−ended mode.
8. VIHD, VILD, VID and VCMR parameters must be complied with simultaneously.
9. The common mode voltage is defined as VIH.
10. Does not include inputs with pulldown resistors.
www.onsemi.com
5
NB3L202K
Table 5. AC TIMING CHARACTERISTICS VDD = VDD_O = 3.3 V ±10% or 2.5 V ±5%, TA = −40°C to 85°C (Note 15)
Symbol
Fmax
Trise/Tfall
Output Slew Rate
DTrise/DTfall
Slew Rate Matching
Characteristics
Min
Maximum Input Frequency
350
Rise Time / Fall Time (Notes 13, 17 and 33) (Figure 13)
175
Output Slew Rate (Notes 13 and 17)
0.5
Typ
Max
Unit
MHz
500
700
ps
2.0
V/ns
Rise/Fall Time Variation (Notes 17 and 26)
125
ps
(Notes 18, 27 and 28)
20%
Vhigh
Voltage High (Notes 17, and 20) (Figure 14)
660
700
850
mV
Vlow
Voltage Low (Notes 17, and 21) (Figure 14)
−150
0
+150
mV
Input Slew Rate
(Note 29 and 32)
0.35
Vcross absolute
Absolute Crossing Point Voltages (Notes 12, 17 and 24)
Relative Crossing Point Voltages can be calculated (Notes 16, 17
and 24) (Figure 16)
250
Total DVcross
Duty Cycle
Total Variation of Vcross Over All Edges (Notes 17 and 25)
(Note 18) (Figure 15)
45
Vovs
Maximum Voltage (Overshoot) (Notes 17 and 22) (Figure 14)
Vuds
Maximum Voltage (Undershoot) (Notes 17 and 23) (Figure 14)
Vrb
Ringback Voltage (Note 17) (Figure 14)
Toe_lat
tpd
V/ns
0.2
OE Latency (Note 11)
Input−to−Output Delay CLK_IN, DIF_[1:0] (Note 31)
tSKEW
Output−to−Output Skew across 2 outputs DIF_[1:0] (Notes 30 and 31)
tJITTERf
Additive RMS Phase Jitter fcarrier = 156.25 MHz, 12 kHz − 20 MHz Integrated Range
550
mV
140
mV
55
%
Vhigh + 0.3
V
Vlow − 0.3
V
N/A
V
4
6
12
Cycles
0.6
1.0
1.4
ns
0
5.0
20
ps
46
80
fs
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
11. Time from deassertion until outputs are >200 mV.
12. Measured at crossing point where the instantaneous voltage value of the rising edge of CLK equals the falling edge of CLK#.
13. Measured from VOL = 0.175 V to VOH = 0.525 V. Only valid for Rising Clock and Falling Clock#.
14. This measurement refers to the total variation from the lowest crossing point to the highest, regardless of which edge is crossing
15. Test configuration is RS = 33.2 W, RP = 49.9, CL = 2 pF, RREF = 475 W.
16. Vcross(rel) Min and Max are derived using the following, Vcross(rel) Min = 0.250 + 0.5 (Vhigh avg − 0.700). Vcross(rel) Max = 0.550 − 0.5
(0.700 – Vhigh avg), (see Figure 16 for further clarification).
17. Measurement taken from Single Ended waveform.
18. Measurement taken from differential waveform.
19. Unless otherwise noted, all specifications in this table apply to all frequencies.
20. Vhigh is defined as the statistical average High value as obtained by using the Oscilloscope Vhigh Math function.
21. Vlow is defined as the statistical average Low value as obtained by using the Oscilloscope Vlow Math function.
22. Overshoot is defined as the absolute value of the maximum voltage.
23. Undershoot is defined as the absolute value of the minimum voltage.
24. The crossing point must meet the absolute and relative crossing point specifications simultaneously.
25. DVcross is defined as the total variation of all crossing voltages of Rising CLOCK and Falling CLOCK#. This is the maximum allowed variance in Vcross for any particular system.
26. Measured with oscilloscope, averaging off, using min max statistics. Variation is the delta between min and max.
27. Matching applies to rising edge rate for clock and falling edge rate for Clock#. It is measured using a ±75 mV window centered on the average
crosspoint where clock rising meets Clock# falling. The median crosspoint is used to calculate the voltage threshold the oscilloscope is to
use for the edge rate calculations.
28. Slew Rate matching is derived using the following, 2 * (Trise – Tfall) / (Trise + Tfall).
29. Input slew rate is based on single ended measurement. This is the minimum input slew rate at which the NB3L202K devices are guaranteed
to meet all performance specifications.
30. Measured into fixed 2 pF load cap. Input to output skew is measured at the first output edge following the corresponding input.
31. Measured from differential cross−point to differential cross−point with scope averaging on to find mean value.
32. The differential input clock is expected to be sourced from a high performance clock oscillator.
33. Measured at 3.3 V ± 10% with typical HCSL input levels.
www.onsemi.com
6
NB3L202K
Figure 3. Typical Phase Noise Plot at fcarrier = 156.25 MHz at an Operating Voltage of 3.3 V, Room Temperature
To obtain the most accurate additive phase noise
measurement, it is vital that the source phase noise be
notably lower than that of the DUT. If the phase noise of the
source is similar or greater than the device under test output,
the source noise will dominate the additive phase jitter
calculation and lead to an artificially low result for the
additive phase noise measurement within the integration
range.
The above phase noise data was captured using Agilent
E5052A/B. The data displays the input phase noise and
output phase noise used to calculate the additive phase jitter
at a specified integration range. The additive RMS phase
jitter contributed by the device (integrated between 12 kHz
and 20 MHz) is 45.7 fs.
The additive RMS phase jitter performance of the fanout
buffer is highly dependent on the phase noise of the input
source.
Additive RMS phase jitter + ǸRMS phase jitter of output 2 * RMS phase jitter of input 2
45.7 fs + Ǹ73.7 fs 2 * 57.8 fs 2
www.onsemi.com
7
NB3L202K
Table 6. ELECTRICAL CHARACTERISTICS − PHASE JITTER PARAMETERS
(VDD = VDD_O = 3.3 V ±10% or 2.5 V ±5%, TA = −40°C to 85°C)
Symbol
Parameter
tjphPCIeG1
tjphPCIeG2
tjphPCIeG3
tjphQPI_SMI
Additive Phase Jitter
Conditions (Notes 34 and 39)
Min
Typ
Max
Unit
PCIe Gen 1 (Notes 35 and 36)
10
ps (p−p)
PCIe Gen 2 Lo Band
10 kHz < f < 1.5 MHz (Notes 35 and 38)
0.3
ps
(rms)
PCIe Gen 2 High Band
1.5 MHz < f < Nyquist (50 MHz)
(Notes 35 and 38)
0.7
ps
(rms)
PCIe Gen 3
(PLL BW of 2−4 MHz, CDR = 10 MHz)
(Notes 35 and 38)
0.3
ps
(rms)
QPI & SMI
(100.00 MHz or 133.33 MHz, 4.8 Gb/s,
6.4 Gb/s 12UI) (Notes 37 and 38)
0.3
ps
(rms)
QPI & SMI
(100.00 MHz, 8.0 Gb/s, 12UI) (Notes 37 and 38)
0.1
ps
(rms)
QPI & SMI
(100.00 MHz, 9.6 Gb/s, 12UI) (Notes 37 and 38)
0.1
ps
(rms)
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
34. Applies to all outputs.
35. See http://www.pcisig.com for complete specs
36. Sample size of at least 100K cycles. This figures extrapolates to 108 ps pk−pk @ 1M cycles for a BER of 1−12.
37. Calculated from Intel−supplied Clock Jitter Tool v 1.6.3.
38. For RMS figures, additive jitter is calculated by solving the following equation: (Additive jitter)2 = (total jitter)2 - (input jitter)2
39. Guaranteed by design and characterization, not tested in production
www.onsemi.com
8
NB3L202K
CLK_IN
VIH
Vth
CLK_IN
VIL
CLK_IN#
CLK_IN#
Vth
Figure 4. Differential Input Driven
Single−Ended
VDD
Vthmax
Figure 5. Differential Inputs
Driven Differentially
VIHmax
VILmax
VIH
Vth
VIL
Vth
CLK_IN#
CLK_IN
VILD
VILmin
GND
Figure 6. Vth Diagram
VDD
Figure 7. Differential Inputs Driven Differentially
VIHDmax
VIHCMR MAX
VILDmax
CLK_IN#
VIHCMR
CLK_IN
VIHDtyp
VID = VIHD − VILD
CLK_IN#
CLK_IN
VIHDmin
VINPP = VIH(CLK_IN) −
VIL(CLK_IN)
DIF_n#
VILDtyp
GND
VIHD
VIHmin
Vthmin
VIHCMR MIN
VID = |VIHD(IN) − VILD(IN)|
DIF_n
VOUTPP = VOH(DIF_n) −
VOL(DIF_n)
tPHL
VILDmin
tPLH
Figure 8. VIHCMR Diagram
Figure 9. AC Reference Measurement
www.onsemi.com
9
NB3L202K
DIF_n
RS1
Z0 = 50 W
Receiver
HCSL
Driver
RS2
Z0 = 50 W
DIF_n#
IREF
CL1
2 pF
RL1
50 W
CL2
2 pF
RL2
50 W
RREF
A. Connect 475 W resistor RREF from IREF pin to GND.
B. RS1, RS2: 33 W for Test and Evaluation. Select to Minimizing Ringing.
C. CL1, CL2: Receiver Input Simulation (for test only not added to application circuit.
D. RL1, RL2 Termination and Load Resistors Located at Received Inputs.
Figure 10. Typical Termination Configuration for Output Driver and Device Evaluation
3.3 V
IREF
IOUT
C1
VMirror
MIref
2R
MMir
MOUTB
MOUT
MDum
R
OUT
~1.1 V
Out_predrv
OUT
RREF
Figure 11. HCSL Simplified Output Structure
www.onsemi.com
10
NB3L202K
NB3L202K
Qx
Zo = 50 W
100 W
HCSL
Device
Qx
100 W
Zo = 50 W
RL = 150 W
IREF
RREF
LVDS
Device
RL = 150 W
GND
Figure 12. HCSL Interface Termination to LVDS
MEASUREMENT POINTS FOR DIFFERENTIAL
TRise (Clock)
VOH = 0.525 V
VCross
VOL = 0.175 V
TFall (Clock#)
Figure 13. Single−Ended Measurement Points for Trise, Tfall
Vovs
Vhigh
Vrb
Vrb
Vlow
Vuds
Figure 14. Single−Ended Measurement Points for Vovs, Vuds, Vrb
www.onsemi.com
11
NB3L202K
TPeriod
High Duty Cycle%
Low Duty Cycle%
Skew measurement point
0.000 V
Figure 15. Differential (CLOCK – CLOCK#) Measurement Points (Tperiod, Duty Cycle)
Vcross(rel) Max
550
500
450
For Vhigh > 700mV
Use Equ. 2
For Vhigh < 700mV
Use Equ. 1
400
Crossing Point (mV)
350
Vcross(rel) Min
300
250
200
625
650
675
700
725
750
775
800
825
850
Vhigh Average (mV)
Equ 1: Vcross(rel) Max = 0.550 − 0.5(0.7 − Vhigh avg)
Equ 2: Vcross(rel) Min = 0.250 + 0.5(Vhigh avg − 0.7)
Figure 16. Vcross Range Clarification (Note 40)
40. The picture above illustrates the effect of Vhigh above and below 700 mV on the Vcross range. The purpose of this is to prevent a 250 mV
Vcross with an 850 mV Vhigh. In addition, this prevents the case of a 550 mV Vcross with a 660 mV Vhigh. The actual specification for Vcross
is dependent upon the measured amplitude of Vhigh.
www.onsemi.com
12
NB3L202K
Signal and Feature Operation
Table 7. OE# FUNCTIONALITY (Notes 41, 42 and 43)
CLK_IN / CLK_IN#
OE# (Pin)
DIF
DIF #
Notes
Running
1
Low
Low
41
Running
0
Running
Running
Not Running
x
x
x
41. The outputs are tri−stated, but the termination networks pull them low
42. OE# pins are asynchronous asserted−low signals.
43. Each OE# pin controls two pair of DIF outputs.
OE# Assertion (Transition from ‘1’ to ‘0’)
OE# De−Assertion (Transition from ‘0’ to ‘1’)
All differential outputs that were tri−stated (low due to
termination pull down) will resume normal operation in a
glitch free manner. The latency from the assertion to active
outputs is 4 − 12 DIF clock periods.
Note: Input clock must remain running for a minimum of
12 clock cycles.
The maximum latency from the de−assertion to tristated
(low due to termination pull down) outputs is 12 DIF clock
periods.
Table 8. NB3L202K RESISTIVE LUMPED TEST LOADS FOR DIFFERENTIAL CLOCKS
Board Target Trace/Term Z
Reference R, Iref = VDD/(3*RREF)
Output Current
VOH @ Z
Rs
Rp
100 W Differential
50 W Single−Ended
RREF = 475 W 1%,
IREF = 2.32 mA
IOH = 6 * IREF
0.7 V @ 50
33 W
5%
50 W
5%
85 W Differential
43 W Single−Ended
RREF = 412 W, 1%,
IREF = 2.67 mA
IOH = 6 * IREF
0.7V @ 43.2
27 W
5%
43 W
5%
ORDERING INFORMATION
Package
Shipping†
NB3L202KMNG
QFN16
(Pb−Free)
123 Units / Rail
NB3L202KMNTXG
QFN16
(Pb−Free)
3000 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
www.onsemi.com
13
NB3L202K
PACKAGE DIMENSIONS
QFN16 3x3, 0.5P
CASE 485AE
ISSUE B
D
A
B
ÇÇ
ÇÇ
PIN 1
LOCATION
L1
DETAIL A
ALTERNATE TERMINAL
CONSTRUCTIONS
E
ÉÉÉ
ÉÉÉ
0.15 C
EXPOSED Cu
0.15 C
TOP VIEW
0.10 C
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.25 AND 0.30 MM FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
5. OUTLINE MEETS JEDEC DIMENSIONS PER
MO−220, VARIATION VEED−6.
L
L
MOLD CMPD
A1
DETAIL B
(A3)
DETAIL B
ÉÉ
ÉÉ
ÇÇ
A3
ALTERNATE
CONSTRUCTIONS
A
0.08 C
A1
SIDE VIEW
NOTE 4
C
SEATING
PLANE
L
DETAIL A
5
8
3.30
E2
K
1
16X
0.65
PACKAGE
OUTLINE
9
4
16X
MILLIMETERS
MIN
MAX
0.80
1.00
0.00
0.05
0.20 REF
0.18
0.30
3.00 BSC
1.25
1.55
3.00 BSC
1.25
1.55
0.50 BSC
0.20
−−−
0.30
0.50
0.00
0.15
RECOMMENDED
SOLDERING FOOTPRINT*
D2
16X
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
L1
1
12
3.30
b
0.10 C A B
16
13
16X
0.05 C
NOTE 3
e
e/2
16X
0.30
BOTTOM VIEW
0.50
PITCH
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
14
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NB3L202K/D
Similar pages