AD AD9625BBPZRL-2.5 1.3 v/2.5 v analog-to-digital converter Datasheet

12-Bit, 2.6 GSPS/2.5 GSPS/2.0 GSPS,
1.3 V/2.5 V Analog-to-Digital Converter
AD9625
Data Sheet
FUNCTIONAL BLOCK DIAGRAM
AVDD
AGND
REFERENCE
DRVDD DRGND
DIGITAL INTERFACE
AND CONTROL
VCM
VIN+
VIN–
ADC
CORE
DDC
fS/8 OR fS/16
SERDOUT[0]±
SERDOUT[1]±
SERDOUT[2]±
SERDOUT[3]±
SERDOUT[4]±
SERDOUT[5]±
SERDOUT[6]±
SERDOUT[7]±
RBIAS_EXT
CONTROL
REGISTERS
SYSREF±
CLK±
CLOCK
MANAGEMENT
AD9625
CMOS DIGITAL
INPUT/OUTPUT
SDIO
SCLK
CSB
CMOS
DIGITAL
INPUT/
OUTPUT
LVDS
DIGITAL
INPUT/
OUTPUT
FD
RSTB
IRQ
SYNCINB±
DIVCLK±
11814-001
12-bit 2.5 GSPS ADC, no missing codes
SFDR = 79 dBc, AIN up to 1 GHz at −1 dBFS, 2.5 GSPS
SFDR = 77 dBc, AIN up to 1.8 GHz at −1 dBFS, 2.5 GSPS
SNR = 57.6 dBFS, AIN up to 1 GHz at −1 dBFS, 2.5 GSPS
SNR = 57 dBFS, AIN up to 1.8 GHz at −1 dBFS, 2.5 GSPS
Noise spectral density = −149.5 dBFS/Hz at 2.5 GSPS
Differential analog input: 1.2 V p-p
Differential clock input
3.2 GHz analog input bandwidth, full power
High speed 6- or 8-lane JESD204B serial output at 2.6 GSPS
Subclass 1: 6.5 Gbps at 2.6 GSPS
Two independent decimate by 8 or decimate by 16 filters
with 10-bit NCOs
Supply voltages: 1.3 V, 2.5 V
Serial port control
Flexible digital output modes
Built-in selectable digital test patterns
Timestamp feature
Conversion error rate < 10−15
JESD204B
INTERFACE
FEATURES
Figure 1.
APPLICATIONS
Spectrum analyzers
Military communications
Radar
High performance digital storage oscilloscopes
Active jamming/antijamming
Electronic surveillance and countermeasures
GENERAL DESCRIPTION
PRODUCT HIGHLIGHTS
The AD9625 is a 12-bit monolithic sampling analog-to-digital
converter (ADC) that operates at conversion rates of up to
2.6 giga samples per second (GSPS). This product is designed
for sampling wide bandwidth analog signals up to the second
Nyquist zone. The combination of wide input bandwidth, high
sampling rate, and excellent linearity of the AD9625 is ideally
suited for spectrum analyzers, data acquisition systems, and a
wide assortment of military electronics applications, such as
radar and electronic countermeasures.
1.
2.
3.
High performance: exceptional SFDR in high sample rate
applications, direct RF sampling, and on-chip reference.
Flexible digital data output formats based on the JESD204B
specification.
Control path SPI interface port that supports various
product features and functions, such as data formatting,
gain, and offset calibration values.
The analog input, clock, and SYSREF± signals are differential
inputs. The JESD204B-based high speed serialized output is
configurable in a variety of one-, two-, four-, six-, or eight-lane
configurations. The product is specified over the industrial
temperature range of −40°C to +85°C, measured at the case.
Rev. C
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2014–2016 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD9625* PRODUCT PAGE QUICK LINKS
Last Content Update: 03/25/2017
COMPARABLE PARTS
REFERENCE MATERIALS
View a parametric search of comparable parts.
Informational
EVALUATION KITS
Press
• 2 AD9625 ADC’s running at 2.5GSPS with an effective
sampling rate of 5GSPS
• 2.6-GHz A/D Converter in High-Reliability Package Meets
Specific Sample Rate and Dynamic Range Requirements
of Aerospace/Defense Applications
• JESD204 Serial Interface
• AD9625 Evaluation and Synchronization
• AD9625 Evaluation Board
• ADA4961 & AD9625 Analog Signal Chain Evaluation and
Converter Synchronization
• ADL5567 & AD9625 Analog Signal Chain Evaluation and
ADF4355-2 Wideband Synthesizer with VCO
• Analog Devices Unveils 2.5-GSPS A/D Converter, Driver
Amplifier and Rapid Prototyping FMC Module
• Global Leader in Converter Technology Releases
Industry’s Highest Performing 2-GSPS Data Converter
• New PLLs Deliver Widest Frequency Range Coverage and
Lowest VCO Phase Noise in a Single Device
DOCUMENTATION
Technical Articles
Data Sheet
• A Test Method for Synchronizing Multiple GSPS
Converters
• AD9625: 12-Bit, 2.6 GSPS/2.5 GSPS/2.0 GSPS, 1.3 V/2.5 V
Analog-to-Digital Converter Data Sheet
User Guides
• Designing High Speed Analog Signal Chains from DC to
Wideband
• AD-FMCADC2-EBZ FMC Board User Guide
• MS-2660: Understanding Spurious-Free Dynamic Range in
Wideband GSPS ADCs
TOOLS AND SIMULATIONS
• MS-2670-1: The Demand for Digital: Challenges and
Solutions for High Speed Analog-to-Digital Converters
and Radar Systems
• Visual Analog
• AD9625 AMI Model
• MS-2672: JESD204B Subclasses - Part 1: An Introduction to
JESD204B Subclasses and Deterministic Latency
• MS-2677: JESD204B Subclasses - Part 2: Subclass 1 vs.
Subclass 2 System Considerations
• MS-2702: Gigasample ADCs Run Fast to Solve New
Challenges
• MS-2708: GSPS Data Converters to the Rescue for
Electronics Surveillance and Warfare Systems
• MS-2714: Understanding Layers in the JESD204B
Specificaton: A High Speed ADC Perspective, Part 1
• MS-2728: Demystifying the Conversion Error Rate of High
Speed ADCs
• MS-2735: Maximizing the Dynamic Range of SoftwareDefined Radio
• Taming the Wideband Conundrum with RF Sampling
ADCs
DESIGN RESOURCES
SAMPLE AND BUY
• AD9625 Material Declaration
Visit the product page to see pricing options.
• PCN-PDN Information
• Quality And Reliability
TECHNICAL SUPPORT
• Symbols and Footprints
Submit a technical question or find your regional support
number.
DISCUSSIONS
View all AD9625 EngineerZone Discussions.
DOCUMENT FEEDBACK
Submit feedback for this data sheet.
This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not
trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.
AD9625
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Numerically Controlled Oscillator .......................................... 33
Applications ....................................................................................... 1
High Bandwidth Decimator ..................................................... 33
Functional Block Diagram .............................................................. 1
Low Bandwidth Decimator ....................................................... 36
General Description ......................................................................... 1
Digital Outputs ............................................................................... 37
Product Highlights ........................................................................... 1
Introduction to the JESD204B Interface ................................. 37
Revision History ............................................................................... 3
Functional Overview ................................................................. 37
Specifications..................................................................................... 4
JESD204B Link Establishment ................................................. 39
DC Specifications ......................................................................... 4
Physical Layer Output................................................................ 43
AC Specifications.......................................................................... 5
Scrambler ..................................................................................... 43
Digital Specifications ................................................................... 6
Tail Bits ........................................................................................ 43
Switching Specifications .............................................................. 7
DDC Modes (Single and Dual) ................................................ 43
Timing Specifications .................................................................. 7
CheckSum ................................................................................... 44
Absolute Maximum Ratings............................................................ 9
8-Bit/10-Bit Encoder Control ................................................... 44
Thermal Characteristics .............................................................. 9
Initial Lane Alignment Sequence (ILAS) ................................ 44
ESD Caution .................................................................................. 9
Lane Synchronization ................................................................ 45
Pin Configuration and Function Descriptions ........................... 10
JESD204B Application Layers .................................................. 48
Typical Performance Characteristics ........................................... 16
Frame Alignment Character Insertion .................................... 51
AD9625-2.0 ................................................................................. 17
Thermal Considerations............................................................ 51
AD9625-2.5 ................................................................................. 20
Power Supply Considerations ................................................... 51
AD9625-2.6 ................................................................................. 24
Serial Port Interface (SPI) .............................................................. 52
Equivalent Test Circuits ................................................................. 27
Configuration Using the SPI ..................................................... 52
Theory of Operation ...................................................................... 28
Hardware Interface..................................................................... 52
ADC Architecture ...................................................................... 28
Memory Map .................................................................................. 53
Fast Detect ................................................................................... 28
Reading the Memory Map Register ......................................... 53
Gain Threshold Operation ........................................................ 28
Memory Map Registers ............................................................. 53
Test Modes ................................................................................... 29
Applications Information .............................................................. 71
Analog Input Considerations ........................................................ 30
Design Guidelines ...................................................................... 71
Differential Input Configurations ............................................ 30
Power and Ground Recommendations ................................... 71
Using the ADA4961 ................................................................... 30
Clock Stability Considerations ................................................. 71
DC Coupling ............................................................................... 32
SPI Port ........................................................................................ 71
Clock Input Considerations ...................................................... 32
Outline Dimensions ....................................................................... 72
Digital Downconverters (DDC) ................................................... 33
Ordering Guide .......................................................................... 72
Frequency Synthesizer and Mixer ............................................ 33
Rev. C | Page 2 of 72
Data Sheet
AD9625
REVISION HISTORY
9/2016—Rev. B to Rev. C
Changes to ADC Output Control Bits on JESD204B Samples
Section ..............................................................................................45
Changes to Table 94 ........................................................................67
Changes to Table 110 and Table 111 .............................................69
Changes to Table 113 and Table 114 .............................................70
Changes to the Clock Stability Considerations Section .............71
Changes to Ordering Guide ...........................................................72
5/2015—Rev. A to Rev. B
Added AD9625-2.6 ....................................................... Throughout
Change to Figure 1 ............................................................................ 1
Changes to Table 1 ............................................................................ 4
Changes to Table 2 ............................................................................ 5
Change to Figure 5 ..........................................................................10
Added Endnote 1, Table 8 ..............................................................11
Added Endnote 2, Table 9 ..............................................................13
Added AD9625-2.6 Section ...........................................................24
Changes to Figure 61 and Figure 63 .............................................27
Changes to Table 11 ........................................................................30
Added Using the ADA4961 Section .............................................30
Added Figure 77; Renumbered Sequentially, Figure 78,
Figure 79, and Figure 80 .................................................................31
Changes to Table 12 ........................................................................34
Changes to Low Bandwidth Decimator Section and Table 13.....36
Changes to Table 28 ........................................................................54
Changes to Table 107 ......................................................................69
Changes to Ordering Guide ...........................................................72
9/2014—Rev. 0 to Rev. A
Added AD9625-2.5 ....................................................... Throughout
Changes to Features and General Description Sections .............. 1
Changes to Table 1 ............................................................................ 4
Changes to Table 2 ............................................................................ 5
Changes to Table 3 ............................................................................ 6
Changes to Table 4 ............................................................................ 7
Changes to Figure 3 and Figure 4.................................................... 8
Changes to Table 6 ............................................................................ 9
Changes to Pin K4; Figure 5, Table 8, and Table 9 ......................10
Added Typical Performance Characteristics Summary and
Changes to Typical Performance Characteristics .......................16
Changes to Figure 45, Figure 49, and Figure 50; Added
Figure 51 to Figure 54 ..................................................................... 23
Changes to Gain Threshold Operation Section .......................... 24
Changes to Analog Input Considerations Section...................... 26
Changes to Digital Downconverters (DDC) Section ................. 28
Added Figure 68 .............................................................................. 32
Changes to Data Streaming Section; Added Link Setup
Parameters Section.......................................................................... 33
Changes to Digital Outputs, Timing, and Controls Section and
Table 15 ............................................................................................. 34
Changes to Table 16 and Table 17 ................................................. 35
Added Table 18 ................................................................................ 36
Added Multichip Synchronization Using SYSREF± Timestamp,
Six Lane Output Mode, and SYSREF± Setup and Hold IRQ
Sections ............................................................................................. 39
Added IRQ Guardband Delays (SYSREF± Setup and Hold)
Section .............................................................................................. 40
Added Using Rising/Falling Edges of CLK to Latch SYSREF±
Section .............................................................................................. 41
Changes to Configuration Using the SPI Section ....................... 46
Changes to Transfer Register Map Section, Table 26, and
Table 27 ............................................................................................. 47
Changes to Table 28, Table 29, and Table 30 ............................... 48
Changes to Table 33 and Table 34 ................................................. 49
Changes to Table 53 ........................................................................ 52
Changes to Table 54 ........................................................................ 52
Changes to Table 58 ........................................................................ 54
Changes to Table 71 ........................................................................ 56
Changes to Table 79 and Table 80 ................................................. 57
Changes to Table 81, Table 82, Table 83, Table 84, Table 85, and
Table 86 ............................................................................................. 58
Changes to Table 89 ........................................................................ 59
Changes to Table 92 and Table 93 ................................................. 60
Changes to Table 94, Table 97, and Table 98 ............................... 61
Changes to Table 101 and Table 106 ............................................. 62
Added Table 107 and Table 108..................................................... 63
Added Table 115 and Table 116..................................................... 64
Added Applications Information Section .................................... 65
Changes to Ordering Guide ........................................................... 66
5/2014—Revision 0: Initial Version
Rev. C | Page 3 of 72
AD9625
Data Sheet
SPECIFICATIONS
DC SPECIFICATIONS
AVDD1 = DVDD1 = DRVDD1 = 1.3 V, AVDD2 = DVDD2 = DRVDD2 = 2.5 V, specified maximum sampling rate, 1.2 V internal
reference, AIN = −1.0 dBFS, default SPI settings, dc-coupled output data, unless otherwise noted.
Table 1.
Parameter
RESOLUTION
ACCURACY
No Missing Codes
Offset Error
Gain Error
Differential Nonlinearity
(DNL)
Integral Nonlinearity (INL)
ANALOG INPUTS
Differential Input
Voltage Range
Resistance
Capacitance
Internal Common-Mode
Voltage (VCM)
Analog Full-Power
Bandwidth2
Input Referred Noise
POWER SUPPLIES
AVDD1
AVDD2
DRVDD1
DRVDD2
DVDD1
DVDD2
DVDDIO
SPI_VDDIO
IAVDD1
IAVDD2
IDRVDD1
IDRVDD2
IDVDD1
IDVDD2
IDVDDIO
ISPI_VDDIO
Power Dissipation
Power-Down Dissipation
1
2
Test Conditions/
Comments
Internal VREF = 1.2 V
Internal termination
Eight lane mode
Temperature1
AD9625-2.0
Min Typ
Max
12
Full
Full
Full
Full
−7
−8
−0.7
Full
−3.6
±0.9
492
1.1
100
1.5
525
Full
25°C
25°C
Full
25°C
25°C
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Guaranteed
±0.5
+6.4
+8
±0.3
+0.7
+3.6
563
Min
12
1.3
2.5
1.3
2.5
1.3
2.5
2.5
2.5
1120
383
456
9
410
<1
<1
<1
3.48
125
Full temperature range is −40°C to +85°C measured at the case (TC).
See Figure 75 and Figure 76 for networks.
Rev. C | Page 4 of 72
Min
12
3.8
3.8
Unit
Bits
Guaranteed
−8.5
±0.5
+7.0
−13.8
+20.9
−0.6
±0.3
+0.7
LSB
%FSR
LSB
−2.1
±1.0
−2.7
±1.0
+2.3
LSB
492
1
100
1.5
525
492
1
100
1.5
525
563
V p-p
Ω
pF
mV
+2.1
563
3.2
2
1.32
2.6
1.32
2.6
1.32
2.6
3.3
3.3
1222
460
470
10
430
AD9625-2.6
Typ
Max
Guaranteed
−7
±0.5
+6.4
−10.8
+14.2
−0.5
±0.3
+0.7
3.2
2
1.26
2.4
1.26
2.4
1.26
2.4
2.4
2.4
AD9625-2.5
Typ
Max
1.26
2.4
1.26
2.4
1.26
2.4
2.4
2.4
1.3
2.5
1.3
2.5
1.3
2.5
2.5
2.5
1250
427
476
9
425
<1
<1
<1
3.90
125
3.2
2
1.32
2.6
1.32
2.6
1.32
2.6
3.3
3.3
1351
491
518
10
473
4.2
1.26
2.4
1.26
2.4
1.26
2.4
2.4
2.4
1.3
2.5
1.3
2.5
1.3
2.5
2.5
2.5
1267
432
497
9
441
<1
<1
<1
4.0
125
GHz
LSBRMS
1.32
2.6
1.32
2.6
1.32
2.6
3.3
3.3
1390
492
544
10
503
4.3
V
V
V
V
V
V
V
V
mA
mA
mA
mA
mA
mA
mA
mA
W
mW
Data Sheet
AD9625
AC SPECIFICATIONS
AVDD1 = DVDD1 = DRVDD1 = 1.3 V, AVDD2 = DVDD2 = DRVDD2 = 2.5 V, specified maximum sampling, 1.2 V internal reference,
AIN = −1.0 dBFS, sample clock input = 1.65 V p-p differential, default SPI settings, unless otherwise noted.
Table 2.
Parameter
SPEED GRADE
ANALOG INPUT
NOISE DENSITY
SIGNAL-TO-NOISE RATIO
(SNR)
fIN = 100 MHz
fIN = 500 MHz
fIN = 1000 MHz
fIN = 1800 MHz
Test Conditions/
Comments
Full scale
Temperature1
Min
Full
25°C
25°C
25°C
25°C
Full
AD9625-2.0
Typ
Max
2.0
1.1
−149.0
55.4
59.5
59.4
59.0
58.2
54.1
58.4
58.4
58.0
57.2
Min
AD9625-2.5
Typ
Max
2.5
1.2
−149.5
54.1
58.3
58.0
57.6
57.0
53.1
57.2
57.0
56.5
55.9
Min
AD9625-2.6
Typ
Max
2.6
1.1
−150.0
Unit
GSPS
V p-p
dBFS/Hz
55.0
58.1
58.0
57.5
56.6
dBFS
dBFS
dBFS
dBFS
53.9
57.0
56.9
56.4
55.6
dBc
dBc
dBc
dBc
SIGNAL-TO-NOISE AND
DISTORTION (SINAD)
fIN = 100 MHz
fIN = 500 MHz
fIN = 1000 MHz
fIN = 1800 MHz
25°C
25°C
25°C
Full
EFFECTIVE NUMBER OF
BITS (ENOB)
fIN = 100 MHz
fIN = 500 MHz
fIN = 1000 MHz
fIN = 1800 MHz
25°C
25°C
25°C
25°C
9.4
9.4
9.3
9.2
9.2
9.2
9.1
9.0
9.2
9.2
9.1
8.9
Bits
Bits
Bits
Bits
25°C
25°C
25°C
Full
80
81
80
76
77
76
79
77
80.5
79.6
77.3
75.4
dBc
dBc
dBc
dBc
−81
−83
−80
dBc
dBc
dBc
dBc
SPURIOUS FREE
DYNAMIC RANGE
(SFDR)
fIN = 100 MHz
fIN = 500 MHz
fIN = 1000 MHz
fIN = 1800 MHz
WORST OTHER SPUR
Including second or
thrid harmonic
fIN = 100 MHz
fIN = 500 MHz
fIN = 1000 MHz
fIN = 1800 MHz
TWO-TONE
INTERMODULATION
DISTORTION (IMD)
fIN1 = 728.5 MHz, fIN2 =
731.5 MHz
fIN1 = 1805.5 MHz, fIN2 =
1808.5 MHz
1
67
70
65
Excluding second or
third harmonic
25°C
25°C
25°C
Full
−80
−86
−83
−85
25°C
−82.8
−81.2
−78.3
dBc
25°C
−77.6
−76.3
−77.7
dBc
−73
−77
−76
−82
−78
−70
−78.0
−66.0
At −7 dBFS per tone
Full temperature range is −40°C to +85°C measured at the case (TC).
Rev. C | Page 5 of 72
AD9625
Data Sheet
DIGITAL SPECIFICATIONS
AVDD1 = DVDD1 = DRVDD1 = 1.3 V, AVDD2 = DVDD2 = DRVDD2 = 2.5 V, specified maximum sampling rate, 1.2 V internal
reference, AIN = −1.0 dBFS, default SPI settings, unless otherwise noted.
Table 3.
Parameter
CLOCK INPUTS (CLK+, CLK−)
Differential Input Voltage
Common-Mode Input Voltage
Input Resistance (Differential)
Input Capacitance
SYSREF INPUTS (SYSREF+, SYSREF−)
Differential Input Voltage
Common-Mode Input Voltage
Input Resistance (Differential)
Input Capacitance
LOGIC INPUTS (SDIO, SCLK, CSB)
Logic Compliance
Voltage
Logic 1
Logic 0
Input Resistance
Input Capacitance
SYNCB+/SYNCB− INPUT
Logic Compliance
Input Voltage
Differential
Common Mode
Input Resistance (Differential)
Input Capacitance
LOGIC OUTPUT (SDIO)
Logic Compliance
Voltage
Logic 1 (IOH = 800 μA)
Logic 0 (IOL = 50 μA)
DIGITAL OUTPUTS (SERDOUT[x]±)
Compliance
Output Voltage
Differential
Offset
Differential Return Loss (RLDIFF)2
Common-Mode Return Loss (RLCM)
Differential Termination Impedance
RESET (RSTB)
Voltage
Logic 1
Logic 0
Input Resistance (Differential)
Input Capacitance
FAST DETECT (FD), PWDN, AND INTERRUPT (IRQ)
Logic Compliance
Voltage
Logic 1
Logic 0
Input Resistance (Differential)
Input Capacitance
1
2
Temperature1
Min
Full
Full
Full
Full
500
Full
Full
Full
Full
500
Typ
Max
Unit
1800
mV p-p
V
kΩ
pF
1800
mV p-p
V
kΩ
pF
0.88
40
1.5
0.88
40
1.5
CMOS
Full
Full
Full
Full
0.8 × SPI_DVDDIO
0.5
30
0.5
Full
Full
Full
Full
Full
V
V
kΩ
pF
LVDS
250
1200
1.2
100
2.5
mV p-p
V
Ω
pF
CMOS
Full
Full
0.8 × SPI_VDDIO
0.3
Full
CML
Full
Full
25°C
25°C
25°C
360
Full
Full
Full
Full
0.8 × DVDDIO
700
DRVDD/2
V
V
800
8
6
100
0.5
20
2.5
mV p-p
mV p-p
dB
dB
Ω
V
V
kΩ
pF
CMOS
Full
Full
Full
Full
0.8 × DVDDIO
0.5
20
2.5
Full temperature range is −40°C to +85°C measured at the case (TC).
Differential and common-mode return loss measured from 100 MHz to 0.75 × baud rate.
Rev. C | Page 6 of 72
V
V
kΩ
pF
Data Sheet
AD9625
SWITCHING SPECIFICATIONS
AVDD1 = DVDD1 = DRVDD1 = 1.3 V, AVDD2 = DVDD2 = DRVDD2 = 2.5 V, specified maximum sampling rate, 1.2 V internal
reference, AIN = −1.0 dBFS, default SPI settings, unless otherwise noted.
Table 4.
Parameter
CLOCK (CLK)
Maximum Clock Rate
Minimum Clock Rate
Clock Pulse Width High
Clock Pulse Width Low
SYSREF (SYSREF±)3
Setup Time (tSU_SR)
Hold Time (tH_SR)
FAST DETECT OUTPUT (FD)
Latency
OUTPUT PARAMETERS (SERDOUT[x]±)
Rise Time
Fall Time
Pipeline Latency
SYNCB± Falling Edge to First K.28 Characters
CGS Phase K.28 Characters Duration
Differential Termination Resistance
APERTURE
Delay
Uncertainty (Jitter)
Out-of-Range Recovery Time
Test Conditions/Comments
Eight lane mode
Temperature1
Min
Full
Full
Full
Full
3302
50 ± 5
50 ± 5
Typ
Max
Unit
2600
MSPS
MSPS
% duty cycle
% duty cycle
25°C
25°C
+200
−100
ps
ps
Full
82
Clock cycles
25°C
25°C
25°C
25°C
25°C
25°C
70
70
226
100
ps
ps
Clock cycles
Multiframes
Multiframes
Ω
200
80
2
ps
fS rms
Clock cycles
4
1
Full
Full
Full
1
Full temperature range is −40°C to +85°C measured at the case (TC).
Must use a two-lane, generic output lane configuration for minimum sample rate. For more information, see the lane table in the JESD204B specification document.
3
SYSREF± setup and hold times are defined with respect to the rising SYSREF± edge and rising clock edge. Positive setup time leads the clock edge. Negative hold time
also leads the clock edge.
2
TIMING SPECIFICATIONS
Table 5.
Parameter
SPI TIMING REQUIREMENTS
tDS
tDH
tCLK
tS
tH
tHIGH
tLOW
tEN_SDIO
tDIS_SDIO
Test Conditions/Comments
Min
Setup time between the data and the rising edge of SCLK
Hold time between the data and the rising edge of SCLK
Period of the SCLK
Setup time between CSB and SCLK
Hold time between CSB and SCLK
Minimum period that SCLK should be in a logic high state
Minimum period that SCLK should be in a logic low state
Time required for the SDIO pin to switch from an input to an
output relative to the SCLK falling edge
Time required for the SDIO pin to switch from an output to an
input relative to the SCLK rising edge
2
2
40
2
2
10
10
10
ns
ns
ns
ns
ns
ns
ns
ns
10
ns
Rev. C | Page 7 of 72
Typ
Max
Unit
AD9625
Data Sheet
Timing Diagrams
CLK–
CLK+
tSU_SR
11814-202
tH_SR
SYSREF–
SYSREF+
Figure 2. SYSREF± Setup and Hold Timing
tDS
tS
tHIGH
tCLK
tDH
tH
tLOW
CSB
SDIO DON’T CARE
DON’T CARE
R/W
W1
W0
A12
A11
A10
A9
A8
A7
D5
D4
D3
D2
D1
D0
DON’T CARE
11814-203
SCLK DON’T CARE
Figure 3. Serial Port Interface Timing Diagram (MSB First)
ANALOG
INPUT
SIGNAL
SAMPLE N
N – 226
N – 225
N+1
N – 224
N–1
CLK–
CLK+
CLK–
CLK+
SERDOUT0±
SAMPLE N – 226
ENCODED INTO 2
8-BIT/10-BIT SYMBOL
SAMPLE N – 225
ENCODED INTO 2
8-BIT/10-BIT SYMBOL
Figure 4. Data Output Timing for Eight Lane Mode
Rev. C | Page 8 of 72
SAMPLE N – 224
ENCODED INTO 2
8-BIT/10-BIT SYMBOL
11814-204
SERDOUT7±
Data Sheet
AD9625
ABSOLUTE MAXIMUM RATINGS
Table 6.
Parameter
Electrical
AVDD1 to AGND
AVDD2 to AGND
DRVDD1 to DRGND
DRVDD2 to DRGND
DVDD1 to DGND
DVDD2 to DGND
DVDDIO to DGND
SPI_VDDIO to DGND
AGND to DRGND
VIN± to AGND
VCM to AGND
VMON to AGND
CLK± to AGND
SYSREF± to AGND
SYNCINB± to DRGND
SCLK to DRGND
SDIO to DRGND
IRQ to DRGND
RSTB to DRGND
CSB to DRGND
FD to DRGND
DIVCLK± to DRGND
SERDOUT[x]± to DRGND
Environmental
Storage Temperature Range
Operating Case Temperature Range
Maximum Junction Temperature
Rating
−0.3 V to +1.32 V
−0.3 V to +2.75 V
−0.3 V to +1.32 V
−0.3 V to +2.75 V
−0.3 V to +1.32 V
−0.3 V to +2.75 V
−0.3 V to +3.63 V
−0.3 V to +3.63 V
−0.3 V to +0.3 V
−0.3 V to AVDD1 + 0.2 V
−0.3 V to AVDD1 + 0.2 V
−0.3 V to AVDD1 + 0.2 V
−0.3 V to AVDD1 + 0.2 V
−0.3 V to AVDD1 + 0.2 V
−0.3 V to DRVDD2 + 0.2 V
−0.3 V to SPI_VDDIO + 0.2 V
−0.3 V to SPI_VDDIO + 0.2 V
−0.3 V to DVDDIO + 0.2 V
−0.3 V to DVDDIO + 0.2 V
−0.3 V to SPI_VDDIO + 0.2 V
−0.3 V to DVDDIO + 0.2 V
−0.3 V to DRVDD2 + 0.2 V
−0.3 V to DRVDD1 + 0.2 V
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
THERMAL CHARACTERISTICS
The following characteristics are for a 4-layer and 10-layer
printed circuit board (PCB).
Table 7. Thermal Resistance
PCB
4-Layer
10-Layer
1
TA (°C)
85.0
85.0
θJA
(°C/W)
18.7
11.5
N/A means not applicable.
ESD CAUTION
−60°C to +150°C
−40°C to +85°C
(measured at case)
110°C
Rev. C | Page 9 of 72
ΨJT
(°C/W)
0.61
0.61
ΨJB
(°C/W)
6.1
4.1
θJC
(°C/W)
1.4
N/A1
AD9625
Data Sheet
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
AD9625
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
AGND
AGND
AGND
AVDD1
AGND
AVDD2
VCM
AGND
VIN+
VIN–
AGND
VM_BYP
AVDD2
AVDD2
B
AGND
AGND
AGND
AGND
AVDD1
AGND
AVDD2
AGND
AGND
AGND
AGND
AVDD2
AGND
AGND
C
AGND
AGND
AGND
AGND
AGND
AVDD1
AGND
AVDD2
AGND
AGND
AVDD2
AGND
AGND
AVDD1
D
DVDD1
DVDD1
DVDD1
DNC
AGND
AGND
AVDD1
AVDD2
AGND
AGND
AVDD2
AVDD1
AVDD1
AVDD1
E
DGND
DGND
DGND
DVDD2
VMON
AGND
AVDD1
AVDD2
AGND
AGND
AVDD2
AVDD1
AGND
AGND
F
DVDD1
DVDD1
DVDD1
SPI_VDDIO
DVDDIO
AGND
AVDD1
AVDD2
AGND
AGND
AVDD2
AVDD1
AGND
CLK+
G
DGND
DGND
DGND
CSB
DVDDIO
AGND
AVDD1
AVDD2
AGND
AGND
AVDD2
AVDD1
AGND
CLK–
H
DVDD1
DVDD1
DVDD1
SCLK
IRQ
AGND
AVDD1
AVDD2
AGND
AGND
AVDD2
AVDD1
AGND
AGND
J
DGND
DGND
DGND
SDIO
FD
RBIAS_EXT
AVDD1
AVDD2
AGND
AGND
AVDD2
AVDD1
AGND
SYSREF+
K
DVDD1
DVDD1
RSTB
PWDN
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
SYSREF–
L
DGND
DNC
DGND
DGND
DGND
DGND
DGND
DNC
DNC
DNC
AGND
AGND
M
DRGND
DRGND
DRGND
DRGND
DRGND
DRGND
DRGND
DRGND
DRGND
DRGND
DRVDD1
REXT
DRGND
DRGND
N
DRVDD1
SERDOUT
[7]+
SERDOUT
[6]+
SERDOUT
[5]+
SERDOUT
[4]+
DRVDD1
SERDOUT
[3]+
SERDOUT
[2]+
SERDOUT
[1]+
SERDOUT
[0]+
DRVDD1
VP_BYP
DRVDD2
DRVDD2
P
DRVDD1
SERDOUT
[7]–
SERDOUT
[6]–
SERDOUT
[5]–
SERDOUT
[4]–
DRVDD1
SERDOUT
[3]–
SERDOUT
[2]–
SERDOUT
[1]–
SERDOUT
[0]–
DRVDD1
DRGND
DIVCLK–
DIVCLK+
SYNCINB– SYNCINB+
NOTES
1. DNC = DO NOT CONNECT. DO NOT CONNECT TO THIS PIN. LEAVE THIS PIN FLOATING.
Figure 5. Pin Configuration
Rev. C | Page 10 of 72
11814-009
TOP VIEW
(Not to Scale)
Data Sheet
AD9625
Table 8. Pin Function Descriptions (By Pin Number)
Pin No.
A1 to A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
B1 to B4
B5
B6
B7
B8 to B11
B12
B13, B14
C1 to C5
C6
C7
C8
C9, C10
C11
C12, C13
C14
D1 to D3
D4
D5, D6
D7
D8
D9, D10
D11
D12 to D14
E1 to E3
E4
E5
E6
E7
E8
E9, E10
E11
E12
E13, E14
F1 to F3
F4
F5
F6
F7
F8
F9, F10
Mnemonic
AGND
AVDD1
AGND
AVDD2
VCM
AGND
VIN+
VIN−
AGND
VM_BYP
AVDD2
AVDD2
AGND
AVDD1
AGND
AVDD2
AGND
AVDD2
AGND
AGND
AVDD1
AGND
AVDD2
AGND
AVDD2
AGND
AVDD1
DVDD1
DNC
AGND
AVDD1
AVDD2
AGND
AVDD2
AVDD1
DGND
DVDD2
VMON
AGND
AVDD1
AVDD2
AGND
AVDD2
AVDD1
AGND
DVDD1
SPI_VDDIO
DVDDIO
AGND
AVDD1
AVDD2
AGND
Type
Ground
Power
Ground
Power
Output
Ground
Input
Input
Ground
Input
Power
Power
Ground
Power
Ground
Power
Ground
Power
Ground
Ground
Power
Ground
Power
Ground
Power
Ground
Power
Power
N/A1
Ground
Power
Power
Ground
Power
Power
Ground
Power
Output
Ground
Power
Power
Ground
Power
Power
Ground
Power
Power
Power
Ground
Power
Power
Ground
Description
ADC Analog Ground. These pins connect to the analog ground plane.
ADC Analog Power Supply (1.30 V).
ADC Analog Ground. This pin connects to the analog ground plane.
ADC Analog Power Supply (2.50 V).
Analog Input, Common Mode (0.525 V).
ADC Analog Ground. This pin connects to the analog ground plane.
Differential Analog Input, True.
Differential Analog Input, Complement.
ADC Analog Ground. This pin connects to the analog ground plane.
Voltage Bypass.
ADC Analog Power Supply (2.50 V).
ADC Analog Power Supply (2.50 V).
ADC Analog Ground. These pins connect to the analog ground plane.
ADC Analog Power Supply (1.30 V).
ADC Analog Ground. This pin connects to the analog ground plane.
ADC Analog Power Supply (2.50 V).
ADC Analog Ground. These pins connect to the analog ground plane.
ADC Analog Power Supply (2.50 V).
ADC Analog Ground. These pins connect to the analog ground plane.
ADC Analog Ground. These pins connect to the analog ground plane.
ADC Analog Power Supply (1.30 V).
ADC Analog Ground. This pin connects to the analog ground plane.
ADC Analog Power Supply (2.50 V).
ADC Analog Ground. These pins connect to the analog ground plane.
ADC Analog Power Supply (2.50 V).
ADC Analog Ground. These pins connect to the analog ground plane.
ADC Analog Power Supply (1.30 V).
ADC Digital Power Supply (1.30 V).
Do Not Connect. Do not connect to this pin. Leave this pin floating.
ADC Analog Ground. These pins connect to the analog ground plane.
ADC Analog Power Supply (1.30 V).
ADC Analog Power Supply (2.50 V).
ADC Analog Ground. These pins connect to the analog ground plane.
ADC Analog Power Supply (2.50 V).
ADC Analog Power Supply (1.30 V).
Digital Control Ground Supply. These pins connect to the digital ground plane.
ADC Digital Power Supply (2.5 V).
CTAT Voltage Monitor Output.
ADC Analog Ground. This pin connects to the analog ground plane.
ADC Analog Power Supply (1.30 V).
ADC Analog Power Supply (2.50 V).
ADC Analog Ground. These pins connect to the analog ground plane.
ADC Analog Power Supply (2.50 V).
ADC Analog Power Supply (1.30 V).
ADC Analog Ground. These pins connect to the analog ground plane.
ADC Digital Power Supply (1.30 V).
SPI Digital Power Supply (2.50 V).
Digital I/O Power Supply (2.50 V).
ADC Analog Ground. This pin connects to the analog ground plane.
ADC Analog Power Supply (1.30 V).
ADC Analog Power Supply (2.50 V).
ADC Analog Ground. These pins connect to the analog ground plane.
Rev. C | Page 11 of 72
AD9625
Pin No.
F11
F12
F13
F14
G1 to G3
G4
G5
G6
G7
G8
G9, G10
G11
G12
G13
G14
H1 to H3
H4
H5
H6
H7
H8
H9, H10
H11
H12
H13, H14
J1 to J3
J4
J5
J6
J7
J8
J9, J10
J11
J12
J13
J14
K1 to K2
K3
K4
K5 to K13
K14
L1
L2
L3
L4
L5 to L9
L10 to L12
L13, L14
M1 to M10
M11
M12
M13, M14
Data Sheet
Mnemonic
AVDD2
AVDD1
AGND
CLK+
DGND
CSB
DVDDIO
AGND
AVDD1
AVDD2
AGND
AVDD2
AVDD1
AGND
CLK−
DVDD1
SCLK
IRQ
AGND
AVDD1
AVDD2
AGND
AVDD2
AVDD1
AGND
DGND
SDIO
FD
RBIAS_EXT
AVDD1
AVDD2
AGND
AVDD2
AVDD1
AGND
SYSREF+
DVDD1
RSTB
PWDN
AGND
SYSREF−
DGND
DNC
SYNCINB−
SYNCINB+
DGND
DNC
AGND
DRGND
DRVDD1
REXT
DRGND
Type
Power
Power
Ground
Input
Ground
Input
Power
Ground
Power
Power
Ground
Power
Power
Ground
Input
Power
Input
Output
Ground
Power
Power
Ground
Power
Power
Ground
Ground
I/O
Output
Input
Power
Power
Ground
Power
Power
Ground
Input
Power
Input
Input
Ground
Input
Ground
N/A1
Input
Input
Ground
N/A1
Ground
Ground
Power
Input
Ground
Description
ADC Analog Power Supply (2.50 V).
ADC Analog Power Supply (1.30 V).
ADC Analog Ground. This pin connects to the analog ground plane.
ADC Clock Input, True.
Digital Control Ground Supply. These pins connect to the digital ground plane.
SPI Chip Select CMOS Input. Active low.
Digital I/O Power Supply (2.50 V).
ADC Analog Ground. This pin connects to the analog ground plane.
ADC Analog Power Supply (1.30 V).
ADC Analog Power Supply (2.50 V).
ADC Analog Ground. These pins connect to the analog ground plane.
ADC Analog Power Supply (2.50 V).
ADC Analog Power Supply (1.30 V).
ADC Analog Ground. This pin connects to the analog ground plane.
ADC Clock Input, Complement.
ADC Digital Power Supply (1.30 V).
SPI Serial Clock CMOS Input.
Interrupt Request Output Signal.
ADC Analog Ground. This pin connects to the analog ground plane.
ADC Analog Power Supply (1.30 V).
ADC Analog Power Supply (2.50 V).
ADC Analog Ground. These pins connect to the analog ground plane.
ADC Analog Power Supply (2.50 V).
ADC Analog Power Supply (1.30 V).
ADC Analog Ground. These pins connect to the analog ground plane.
Digital Control Ground Supply. These pins connect to the digital ground plane.
SPI Serial Data CMOS Input/Output; Scan Output 1.
Fast Detect Output. This pin requires an external 10 kΩ resistor connected to ground.
Reference Bias. This pin requires an external 10 kΩ resistor connected to ground.
ADC Analog Power Supply (1.30 V).
ADC Analog Power Supply (2.50 V).
ADC Analog Ground. These pins connect to the analog ground plane.
ADC Analog Power Supply (2.50 V).
ADC Analog Power Supply (1.30 V).
ADC Analog Ground. This pin connects to the analog ground plane.
System Reference Chip Synchronization, True.
ADC Digital Power Supply (1.30 V).
Chip Digital Reset, Active Low.
Power-down.
ADC Analog Ground. These pins connect to the analog ground plane.
System Reference Chip Synchronization, Complement.
Digital Control Ground Supply. This pin connects to the digital ground plane.
Do Not Connect. Do not connect to this pin. Leave this pin floating.
Synchronization, Complement.
Synchronization, True. SYNCINB LVDS input (active low, true).
Digital Control Ground Supply. These pins connect to the digital ground plane.
Do Not Connect. Do not connect to these pins. Leave these pins floating.
ADC Analog Ground. These pins connect to the analog ground plane.
Digital Driver Ground Supply. These pins connect to the digital driver ground plane.
Power Supply (1.3 V) Reference Clock Divider, VCO, and Synthesizer.
External Resistor, 10 kΩ to Ground.
Digital Driver Ground Supply. This pin connects to the digital driver ground plane.
Rev. C | Page 12 of 72
Data Sheet
Pin No.
N1
N2
N3
N4
N5
N6
N7
N8
N9
N10
N11
N12
N13, N14
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
1
Mnemonic
DRVDD1
SERDOUT[7]+
SERDOUT[6]+
SERDOUT[5]+
SERDOUT[4]+
DRVDD1
SERDOUT[3]+
SERDOUT[2]+
SERDOUT[1]+
SERDOUT[0]+
DRVDD1
VP_BYP
DRVDD2
DRVDD1
SERDOUT[7]−
SERDOUT[6]−
SERDOUT[5]−
SERDOUT[4]−
DRVDD1
SERDOUT[3]−
SERDOUT[2]−
SERDOUT[1]−
SERDOUT[0]−
DRVDD1
DRGND
DIVCLK−
DIVCLK+
AD9625
Type
Power
Output
Output
Output
Output
Power
Output
Output
Output
Output
Power
Input
Power
Power
Output
Output
Output
Output
Power
Output
Output
Output
Output
Power
Ground
Output
Output
Description
Serial Digital Power Supply (1.3 V).
Lane 7 CML Output Data, True.
Lane 6 CML Output Data, True.
Lane 5 CML Output Data, True.
Lane 4 CML Output Data, True.
Serial Digital Power Supply (1.3 V).
Lane 3 CML Output Data, True.
Lane 2 CML Output Data, True.
Lane 1 CML Output Data, True.
Lane 0 CML Output Data, True.
Serial Digital Power Supply (1.3 V).
Voltage Bypass.
Power Supply (2.5 V) Reference Clock Divider for SYNCINB±, DIVCLK±.
Serial Digital Power Supply (1.3 V).
Lane 7 CML Output Data, Complement.
Lane 6 CML Output Data, Complement.
Lane 5 CML Output Data, Complement.
Lane 4 CML Output Data, Complement.
Serializer Digital Power Supply (1.30 V).
Lane 3 CML Output Data, Complement.
Lane 2 CML Output Data, Complement.
Lane 1 CML Output Data, Complement.
Lane 0 CML Output Data, Complement.
Serializer Digital Power Supply (1.30 V).
Digital Driver Ground Supply. This pin connects to the digital driver ground plane.
Divide-by-4 Reference Clock LVDS, Complement.
Divide-by-4 Reference Clock LVDS, True.
N/A means not applicable.
Table 9. Pin Function Descriptions (By Function)1
Pin No.
General Power and Ground Supply Pins
A1 to A3, A5, A8, A11, B1 to B4, B6, B8 to B11,
B13, B14, C1 to C5, C7, C9, C10, C12, C13, D5,
D6, D9, D10, E6, E9, E10, E13, E14, F6, F9, F10,
F13, G6, G9, G10, G13, H6, H9, H10, H13, H14,
J9, J10, J13, K5 to K13, L13, L14
J6
Clock Pins
F14
G14
ADC Analog Power and Ground Supplies Pins
A6, A13, A14, B7, B12, C8, C11, D8, D11, E8,
E11, F8, F11, G8, G11, H8, H11, J8, J11
A4, B5, C6, C14, D7, D12 to D14, E7, E12, F7,
F12, G7, G12, H7, H12, J7, J12
A12
A1 to A3, A5, A8, A11, B1 to B4, B6, B8 to B11,
B13, B14, C1 to C5, C7, C9, C10, C12, C13,D5,
D6, D9, D10, E6, E9, E10, E13, E14, F6, F9, F10,
F13, G6, G9, G10, G13, H6, H9, H10, H13, H14,
J9, J10, J13, K5 to K13, L13, L14
Mnemonic
Type
Description
AGND
Ground
ADC Analog Ground. These pins connect to the analog
ground plane.
RBIAS_EXT
Input
Reference Bias. This pin requires an external 10 kΩ resistor
connected to ground.
CLK+
CLK−
Input
Input
ADC Clock Input, True.
ADC Clock Input, Complement.
AVDD2
Power
ADC Analog Power Supply (2.50 V).
AVDD1
Power
ADC Analog Power Supply (1.30 V).
VM_BYP
AGND
Input
Ground
Voltage Bypass.
ADC Analog Ground. These pins connect to the analog
ground plane.
Rev. C | Page 13 of 72
AD9625
Pin No.
ADC Analog Input and Outputs Pins
A9
A10
A7
E5
JESD204B High Speed Power and Ground Pins
N1, N6, N11, P1, P6, P11
M1 to M10, M13, M14, P12
Data Sheet
Mnemonic
Type
Description
VIN+
VIN−
VCM
VMON
Input
Input
Output
Output
Differential Analog Input, True.
Differential Analog Input, Complement.
Analog Input, Common Mode (0.525 V).
CTAT Voltage Monitor Output (Diode Temperature Sensor).
DRVDD1
DRGND
Power
Ground
N13, N14
DRVDD2
Power
M11
DRVDD1
Power
N12
L2
JESD204B High Speed Serial I/O Pins
J14
K14
L4
L3
VP_BYP
DNC
Input
N/A2
Serial Digital Power Supply (1.3 V).
Digital Driver Ground Supply. These pins connect to the
digital driver ground plane.
Power Supply (2.5 V) Reference Clock Divider, SYNCINB±,
DIVCLK±.
Power Supply (1.3 V) Reference Clock Divider, VCO, and
Synthesizer.
Voltage Bypass.
Do Not Connect. Do not connect to this pin.
SYSREF+
SYSREF−
SYNCINB+
SYNCINB−
Input
Input
Input
Input
N10
P10
N9
P9
N8
P8
N7
P7
N5
P5
N4
P4
N3
P3
N2
P2
P14
P13
Digital Supply and Ground Pins
D1 to D3, F1 to F3, H1 to H3, K1 to K2
F5, G5
F4
E4
E1 to E3, G1 to G3, J1 to J3, L1, L5 to L9
SERDOUT[0]+
SERDOUT[0]−
SERDOUT[1]+
SERDOUT[1]−
SERDOUT[2]+
SERDOUT[2]−
SERDOUT[3]+
SERDOUT[3]−
SERDOUT[4]+
SERDOUT[4]−
SERDOUT[5]+
SERDOUT[5]−
SERDOUT[6]+
SERDOUT[6]−
SERDOUT[7]+
SERDOUT[7]−
DIVCLK+
DIVCLK−
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
DVDD1
DVDDIO
SPI_VDDIO
DVDD2
DGND
Power
Power
Power
Power
Ground
DNC
N/A2
RSTB
PWDN
REXT
CSB
SCLK
Input
Input
Input
Input
Input
D4
Digital Control Pins
K3
K4
M12
G4
H4
Rev. C | Page 14 of 72
System Reference Chip Synchronization, True.
System Reference Chip Synchronization, Complement.
Synchronization, True. SYNCINB LVDS input (active low, true).
Synchronization, Complement. SYNCINB LVDS input (active
low, complement).
Lane 0 CML Output Data, True.
Lane 0 CML Output Data, Complement.
Lane 1 CML Output Data, True.
Lane 1 CML Output Data, Complement.
Lane 2 CML Output Data, True.
Lane 2 CML Output Data, Complement.
Lane 3 CML Output Data, True.
Lane 3 CML Output Data, Complement.
Lane 4 CML Output Data, True.
Lane 4 CML Output Data, Complement.
Lane 5 CML Output Data, True.
Lane 5 CML Output Data, Complement.
Lane 6 CML Output Data, True.
Lane 6 CML Output Data, Complement.
Lane 7 CML Output Data, True.
Lane 7 CML Output Data, Complement.
Divide-by-4 Reference Clock LVDS, True.
Divide-by-4 Reference Clock LVDS, Complement.
ADC Digital Power Supply (1.3 V).
Digital I/O Power Supply (2.5 V).
SPI Digital Power Supply (2.5 V).
ADC Digital Power Supply (2.5 V).
Digital Control Ground Supply. These pins connect to the
digital ground plane.
Do Not Connect. Do not connect to this pin. Leave this pin
floating.
Chip Digital Reset, Active Low.
Power-down for the AD9625.
External Resistor, 10 kΩ to Ground.
SPI Chip Select CMOS Input. Active low.
SPI Serial Clock CMOS Input.
Data Sheet
Pin No.
J4
J5
H5
L10 to L12
1
2
AD9625
Mnemonic
SDIO
FD
Type
I/O
Output
IRQ
DNC
Output
N/A2
Description
SPI Serial Data CMOS Input/Output.
Fast Detect Output. This pin requires an external 10 kΩ
resistor connected to ground.
Interrupt Request Output Signal.
Do Not Connect. Do not connect to these pins. Leave these
pins floating.
Note that when pins are relevant to multiple categories, they are repeated in Table 9. Pins may not appear in alphanumeric order within Table 9.
N/A means not applicable.
Rev. C | Page 15 of 72
AD9625
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
100
0
95
–1
90
SFDR (dBc), 240MHz
–2
AMPLITUDE (dBFS)
85
75
SFDR (dBc), 1821MHz
70
65
SNR (dBFS), 240MHz
60
55
2500
Figure 6. SNR/SFDR vs. Sample Rate
FOUR LANE
MODE
1100
1000
IAVDD1
900
5000
4.5
1.0
4.0
0.9
3.5
0.8
EIGHT LANE
MODE
TOTAL
POWER
800
700
IDRVDD1
IAVDD2
3.0
VMON (V)
TWO LANE
MODE
1200
1000
Figure 8. Full Power Input Bandwidth (Input Network in Figure 76 Used
>2 GHz, Input Network in Figure 75 Used <2 GHz)
POWER (W)
1300
100
INPUT FREQUENCY (MHz)
11814-330
2300
2100
1900
1700
1500
1300
1100
900
700
500
300
SAMPLE RATE (MSPS)
CURRENT (mA)
–6
–9
10
40
500
–5
–8
45
600
–4
–7
SNR (dBc), 1821MHz
50
–3
11814-326
SNR/SFDR (dB)
80
0.7
400
300
SAMPLE RATE (MSPS)
2500
2300
2100
1900
1700
1500
1300
1100
900
700
500
0
300
0.6
2.0
0.5
–50
Figure 7. Current and Power vs. Sample Rate: Two Lane, Four Lane, and Eight
Lane Output Modes
–25
0
25
50
75
JUNCTION TEMPERATURE (°C)
100
125
11814-344
100
2.5
IDVDD2 , IDRVDD2
IDVDD1
11814-322
200
Figure 9. VMON Output Voltage vs. Junction Temperature VMON (V) =
−0.0013 × TEMP(C) + 0.8675
Rev. C | Page 16 of 72
Data Sheet
AD9625
AD9625-2.0
For the AD9625-2.0 model, the full-scale range used is 1.1 V.
0
–40
–60
–80
–40
–60
–80
0
200
400
600
800
1000
FREQUENCY (MHz)
Figure 10. FFT Plot at 2.0 GSPS, fIN = 3010 MHz at AIN (SFDR = 73.1 dBc,
SNR = 56.2 dBFS) (Input Network in Figure 76 Used)
0
–120
11814-308
–120
0
400
600
800
1000
FREQUENCY (MHz)
Figure 13. FFT Plot at 2.0 GSPS, fIN = 310.3 MHz at AIN (SFDR = 82.2 dBc,
SNR = 59.6 dBFS)
100
2000MSPS
1807.3MHz AT –1dBFS
SNR = 58.12dBFS
SFDR = 75.5dBc
–20
200
11814-106
–100
–100
90
80
SFDR (dBFS)
70
–40
SNR/SFDR (dB)
AMPLITUDE (dBFS)
2000MSPS
310.3MHz AT –1dBFS
SNR = 59.6dBFS
SFDR = 82.2dBc
–20
AMPLITUDE (dBFS)
–20
AMPLITUDE (dBFS)
0
2000MSPS
3010MHz AT –1.0dBFS
SNR = 56.2dBFS
SFDR = 73.1dBc
–60
–80
SNR (dBFS)
60
50
SFDR (dBc)
40
30
–100
SNR (dB)
20
200
400
600
800
1000
FREQUENCY (MHz)
0
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
AMPLITUDE (dB)
11814-108
0
11814-104
10
–120
Figure 14. SNR/SFDR vs. Analog Input Amplitude at 2.0 GSPS,
fIN = 241.1 MHz at AIN
Figure 11. FFT Plot at 2.0 GSPS, fIN = 1807.3 MHz at AIN (SFDR = 75.5 dBc,
SNR = 58.12 dBFS)
100
0
2000MSPS
730.3MHz AT –1dBFS
SNR = 59.19dBFS
–20 SFDR = 80.9dBc
90
80
SFDR (dBFS)
SNR/SFDR (dB)
–60
–80
SNR (dBFS)
60
50
SFDR (dBc)
40
30
SNR (dB)
20
–100
–120
0
200
400
600
FREQUENCY (MHz)
800
1000
11814-105
10
Figure 12. FFT Plot at 2.0 GSPS, fIN = 730.3 MHz at AIN (SFDR = 80.9 dBc,
SNR = 59.19 dBFS)
Rev. C | Page 17 of 72
0
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
AMPLITUDE (dB)
Figure 15. SNR/SFDR vs. Analog Input Amplitude at 2.0 GSPS,
fIN = 1811.3 MHz at AIN
11814-109
AMPLITUDE (dBFS)
70
–40
AD9625
Data Sheet
120
90
+90°C
+25°C
–55°C
IMD3 (dBFS)
85
100
80
SFDR (dBFS)
SNR/SFDR (dB)
SFDR (dB)
80
60
SFDR (dBc)
40
SFDR (dBc)
75
70
65
60
20
–80
–70
–60
–50
–40
–30
–20
–10
0
AMPLITUDE (dBFS)
11814-112
0
–90
Figure 16. Two Tone SFDR and IMD3 vs. Analog Input Amplitude at 2.0 GSPS
at 1800 MHz AIN
120
50
100
700
900
0
AMPLITUDE (dBFS)
60
SFDR (dBc)
40
1300
1500
1700
1900
2000MSPS
fIN1 = 1805.5MHz AT –7.0dBFS
fIN2 = 1808.5MHz AT –7.0dBFS
SFDR = 78.117dBc
–20
SFDR (dBFS)
1100
Figure 19. SNR/SFDR vs. Analog Input Frequency at Different Temperatures
at 2.0 GSPS
IMD3 (dBFS)
80
20
–40
–60
–80
–80
–70
–60
–50
–40
–30
–20
–10
0
AMPLITUDE (dBFS)
–120
11814-215
0
–90
0
0
–20
4.0
AMPLITUDE (dBFS)
2.0
1.5
800
1000
2000MSPS
fIN1 = 728.5MHz AT –7.0dBFS
fIN2 = 731.5MHz AT –7.0dBFS
SFDR = 80.98dBc
4.5
2.5
600
Figure 20. Two Tone FFT Plot at 2.0 GSPS, fIN1 = 1805.5 MHz and
fIN2 = 1808.5 MHz at AIN, −7.0 dBFS (SFDR = 78.117 dBc)
5.0
3.0
400
FREQUENCY (MHz)
Figure 17. Two Tone SFDR and IMD3 vs. Analog Input Amplitude at 2.0 GSPS
at 230 MHz AIN
3.5
200
11814-219
–100
–40
–60
–80
1.0
–100
0
MORE
N–4
N–2
N
N+2
N+4
MORE
BINS
11814-114
0.5
Figure 18. Input Referred Noise Histogram with 2.0 GSPS
–120
0
200
400
600
800
1000
FREQUENCY (MHz)
Figure 21. Two Tone FFT Plot at 2.0 GSPS, fIN1 = 728.5 MHz and
fIN2 = 731.5 MHz at AIN, −7.0 dBFS (SFDR = 80.98 dBc)
Rev. C | Page 18 of 72
11814-220
SFDR (dB)
500
ANALOG INPUT FREQUENCY (MHz)
100
HITS (Millions)
300
11814-113
SNR (dBFS)
55
Data Sheet
AD9625
0
–20
0.4
0.2
–60
–80
–0.2
–100
–0.4
–120
0
200
400
600
800
1000
FREQUENCY (MHz)
0.5
0.4
0.3
0.2
0.1
0
–0.1
–0.2
–0.3
1023
2047
3071
4095
CODES
11814-222
–0.4
–0.5
–1
–0.6
0
1024
2048
3072
4096
CODES
Figure 24. Integral Nonlinearity (INL), ±0.4 LSB at 2.0 GSPS
Figure 22. Two Tone FFT Plot at 2.0 GSPS, fIN1 = 228.5 MHz and
fIN2 = 231.5 MHz at AIN, −7.0 dBFS (SFDR = 80.76 dBc)
DNL (LSB)
0
Figure 23. Differential Nonlinearity (DNL), ±0.2 LSB at 2.0 GSPS
Rev. C | Page 19 of 72
11814-223
INL (LSB)
–40
11814-221
AMPLITUDE (dBFS)
0.6
2000MSPS
fIN1 = 228.5MHz AT –7.0dBFS
fIN2 = 231.5MHz AT –7.0dBFS
SFDR = 80.76dBc
AD9625
Data Sheet
AD9625-2.5
For the AD9625-2.5 model, full-scale range used is 1.2 V.
0
–40
–60
–80
0
750
1000
1250
–60
–80
500
750
1000
1250
FREQUENCY (MHz)
Figure 26. FFT Plot at 2.5 GSPS, fIN = 730.3 MHz at AIN (SFDR = 77.1 dBc,
SNR = 57.8 dBFS)
0
500
750
1000
1250
–142
–144
–146
–148
–150
0
1000
2000
3000
4000
5000
6000
INPUT FREQUENCY (MHz)
Figure 29. Noise Specrtal Density (NSD) vs. AIN at 2.5 GSPS (Input Network in
Figure 76 Used <2 GHz, Input Network in Figure 75 Used >2 GHz)
100
2500MSPS
115.05MHz AT –1.0dBFS
SNR = 58.1dBFS
SFDR = 78.4dBc
–20
250
Figure 28. FFT Plot at 2.5 GSPS, fIN = 2990.11 MHz at AIN (SFDR = 70.6 dBc,
SNR = 55.3 dBFS) (Input Network in Figure 75 Used)
11814-307
–100
250
0
FREQUENCY (MHz)
NOISE SPECTRAL DENSITY (dBFS/Hz)
–40
0
–120
–140
2500MSPS
730.3MHz AT –1.0dBFS
SNR = 57.8dBFS
SFDR = 77.1dBc
–20
AMPLITUDE (dBFS)
–80
11814-310
500
Figure 25. FFT Plot at 2.5 GSPS, fIN = 1816.7 MHz at AIN (SFDR = 80.35 dBc,
SNR = 57.1 dBFS)
90
80
SFDR (dBFS)
70
–40
SNR/SFDR (dB)
AMPLITUDE (dBFS)
–60
11814-311
250
11814-306
0
FREQUENCY (MHz)
–120
–40
–100
–100
–120
2500MSPS
2990.11MHz AT –1.0dBFS
SNR = 55.3dBFS
SFDR = 70.6dBc
–20
AMPLITUDE (dBFS)
–20
AMPLITUDE (dBFS)
0
2500MSPS
1816.7MHz AT –1.0dBFS
SNR = 57.1dBFS
SFDR = 80.35dBc
–60
–80
SNR (dBFS)
60
50
SFDR (dBc)
40
30
SNR (dB)
20
–100
0
250
500
750
FREQUENCY (MHz)
1000
1250
0
–90
11814-309
–120
Figure 27. FFT Plot at 2.5 GSPS, fIN = 115.05 MHz at AIN (SFDR = 78.4 dBc,
SNR = 58.1 dBFS)
–80
–70
–60
–50
–40
AMPLITUDE (dB)
–30
–20
–10
0
11814-320
10
Figure 30. SNR/SFDR vs. Analog Input Amplitude at 2.5 GSPS, fIN = 241 MHz
at AIN
Rev. C | Page 20 of 72
Data Sheet
AD9625
100
120
90
80
SFDR (dBFS)
100
SNR (dBFS)
80
60
SFDR (dB)
SNR/SFDR (dB)
70
50
SFDR (dBc)
40
IMD3 (dBFS)
SFDR (dBFS)
60
40
30
SFDR (dBc)
SNR (dB)
20
20
–80
–70
–60
–50
–40
–30
–20
–10
0
AMPLITUDE (dB)
0
–90
11814-321
0
–90
Figure 31. SNR/SFDR vs. Analog Input Amplitude at 2.5 GSPS, fIN = 1811 MHz
at AIN
–80
–70
–60
–50
–40
–30
–20
–10
AMPLITUDE (dBFS)
11814-327
10
Figure 34. Two Tone SFDR and IMD3 vs. Analog Input Amplitude at 2.5 GSPS
at 1800 MHz AIN
60
120
–40°C
59
IMD3 (dBFS)
+25°C
58
100
57
+85°C
80
55
SFDR (dB)
SNR (dBFS)
56
54
53
52
SFDR (dBFS)
60
40
SFDR (dBc)
51
50
20
0
500
1000
1500
2000
2500
3000
INPUT FREQUENCY (MHz)
0
–90
11814-323
48
Figure 32. SNR at 2.5 GSPS vs. Temperature (Input Network in Figure 76 Used
<2 GHz, Input Network in Figure 75 Used >2 GHz)
–80
–70
–60
–50
–40
–30
–20
–10
AMPLITUDE (dBFS)
11814-328
49
Figure 35. Two Tone SFDR and IMD3 vs. Analog Input Amplitude at 2.5 GSPS
at 230 MHz AIN
85
120
IMD3 (dBFS)
+25°C
80
100
75
–40°C
80
SFDR (dB)
SFDR (dBc)
70
65
+85°C
60
55
SFDR (dBFS)
60
40
SFDR (dBc)
50
20
0
500
1000
1500
2000
INPUT FREQUENCY (MHz)
2500
3000
0
–90
11814-324
40
Figure 33. SFDR at 2.5 GSPS vs. Temperature (Input Network in Figure 76
Used <2 GHz, Input Network in Figure 75 Used >2 GHz)
–80
–70
–60
–50
–40
AMPLITUDE (dBFS)
–30
–20
–10
11814-329
45
Figure 36. Two Tone SFDR and IMD3 vs. Analog Input Amplitude at 2.5 GSPS
at 730 MHz AIN
Rev. C | Page 21 of 72
AD9625
Data Sheet
85
59
80
58
57
75
56
SNR (dBFS)
SFDR (dBc)
70
65
60
55
55
54
53
52
51
50
50
45
6000
ANALOG INPUT FREQUENCY (MHz)
48
100
11814-331
1000
Figure 37. SFDR vs. AIN Frequency at 2.5 GSPS (Input Network in Figure 76
Used <2 GHz, Input Network in Figure 75 used >2 GHz)
1000
6000
ANALOG INPUT FREQUENCY (MHz)
11814-332
49
40
100
Figure 40. SNRFS vs. AIN Frequency at 2.5 GSPS (Input Network in Figure 76
Used <2 GHz, Input Network in Figure 75 Used >2 GHz)
4.0
0
2500MSPS
fIN1 = 1808.5MHz AT –7.0dBFS
fIN2 = 1805.5MHz AT –7.0dBFS
SFDR = 75.9dBc
3.5
–20
AMPLITUDE (dBFS)
HITS (Millions)
3.0
2.5
2.0
1.5
–40
–60
–80
1.0
N–4
N–2
N
N+2
N+4
N + 6 MORE
CODE
–120
11814-333
0
MORE N – 6
0
500
750
1000
1250
FREQUENCY (MHz)
Figure 41. Two Tone FFT Plot at 2.5 GSPS, fIN1 = 1808.5 MHz and
fIN2 = 1805.5 MHz at AIN, −7.0 dBFS (SFDR = 75.9 dBc)
Figure 38. Input Referred Noise Histogram with 2.5 GSPS
0
0.5
2500MSPS
fIN1 = 728.5MHz AT –7.0dBFS
fIN2 = 731.5MHz AT –7.0dBFS
SFDR = 79.3dBc
0.4
–20
0.3
AMPLITUDE (dBFS)
0.2
0.1
0
–0.1
–0.2
–0.3
–40
–60
–80
–100
–0.5
0
1024
2048
3072
4096
CODES
–120
0
250
500
750
1000
1250
FREQUENCY (MHz)
Figure 42. Two Tone FFT Plot at 2.5 GSPS, fIN1 = 728.5 MHz and
fIN2 = 731.5 MHz at AIN, −7.0 dBFS (SFDR = 79.3 dBc)
Figure 39. Differential Nonlinearity (DNL), ±0.3 LSB at 2.5 GSPS
Rev. C | Page 22 of 72
11814-335
–0.4
11814-341
DNL (LSB)
250
11814-334
–100
0.5
Data Sheet
AD9625
0
–20
1.0
–40
–60
0
–80
–0.5
–100
–1.0
–120
0
250
500
750
1000
1250
FREQUENCY (MHz)
–1.5
0
1024
2048
3072
4096
CODES
Figure 44. Integral Nonlinearity (INL), ±1.0 LSB at 2.5 GSPS
Figure 43. Two Tone FFT Plot at 2.5 GSPS, fIN1 = 228.5 MHz and
fIN2 = 231.5 MHz at AIN, −7.0 dBFS (SFDR = 76.7 dBc)
Rev. C | Page 23 of 72
11814-343
INL (LSB)
0.5
11814-336
AMPLITUDE (dBFS)
1.5
2500MSPS
fIN1 = 228.5MHz AT –7.0dBFS
fIN2 = 231.5MHz AT –7.0dBFS
SFDR = 76.7dBc
AD9625
Data Sheet
AD9625-2.6
For the AD9625-2.6 model, full-scale range used is 1.1 V.
0
100
2600MSPS
1820.825MHz AT –1dBFS
SNR = 55.556dB
SFDR = 76.47dBc
–15
90
70
–45
SNR/SFDR (dB)
AMPLITUDE (dBFS)
SFDR (dBFS)
80
–30
–60
–75
60
SNR (dBFS)
50
SFDR (dBc)
40
30
–90
SNR (dB)
20
–105
150
300
450
600
750
900
1050
1200
FREQUENCY (MHz)
0
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
AMPLITUDE (dB)
Figure 45. FFT Plot at 2.6 GSPS, fIN = 1820.825 MHz at AIN
(SFDR = 76.47 dBc, SNR = 55.556 dB)
0
Figure 48. SNR/SFDR vs. Analog Input Amplitude at 2.6 GSPS,
fIN = 1811 MHz at AIN
100
2600MSPS
729.028MHz AT –1dBFS
SNR = 56.766dB
SFDR = 78.248dBc
–15
90
80
SFDR (dBFS)
70
SNR/SFDR (dB)
–45
–60
–75
SNR (dBFS)
60
SFDR (dBc)
50
40
–90
30
–105
20
SNR (dB)
150
300
450
600
750
900
1050
1200
FREQUENCY (MHz)
0
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
AMPLITUDE (dB)
Figure 46. FFT Plot at 2.6 GSPS, fIN = 729.028 MHz at AIN
(SFDR = 78.248 dB, SNR = 56.766)
0
Figure 49. SNR/SFDR vs. Analog Input Amplitude at 2.6 GSPS,
fIN = 241 MHz at AIN
59
2600MSPS
113.940MHz AT –1dBFS
SNR = 57.159dB
SFDR = 81.161dBc
–15
58
+25°C
57
–30
56
–45
SNR (dBFS)
AMPLITUDE (dBFS)
11814-512
10
0
11814-503
AMPLITUDE (dBFS)
–30
–120
11814-513
0
11814-506
10
–120
–60
–75
+85°C
55
–40°C
54
53
52
–90
51
–105
50
150
300
450
600
750
FREQUENCY (MHz)
900
1050
1200
Figure 47. FFT Plot at 2.6 GSPS, fIN = 113.940 MHz at AIN (SFDR = 81.161,
SNR = 57.159)
Rev. C | Page 24 of 72
48
0
400
800
1200
1600
INPUT FREQUENCY (MHz)
Figure 50. SNR vs. Temperature at 2.6 GSPS
2000
11814-515
0
11814-500
49
–120
Data Sheet
AD9625
100
120
IMD3 (dBFS)
90
–40°C
100
80
+25°C
60
SFDR/IMD3 (dB)
SFDR (dBFS)
70
+85°C
50
40
30
SFDR (dBFS)
80
60
SFDR (dBc)
40
20
0
400
800
1200
1600
2000
INPUT FREQUENCY (MHz)
11814-516
0
0
–90
–80
–70
–60
–50
–40
–30
–20
–10
AMPLITUDE (dBFS)
Figure 51. SFDR vs. Temperature at 2.6 GSPS
11814-519
20
10
Figure 54. Two Tone SFDR and IMD3 vs. Analog Input Amplitude at
2.6 GSPS at 1807 MHz AIN
4.0
120
IMD3 (dBFS)
3.5
100
HITS (Millions)
SFDR/IMD3 (dB)
3.0
SFDR (dBFS)
80
60
SFDR (dBc)
2.5
2.0
1.5
40
1.0
20
BINS
Figure 55. Input Referred Noise Histogram with 2.6 GSPS
Figure 52. Two Tone SFDR and IMD3 vs. Analog Input Amplitude at
2.6 GSPS at 230 MHz AIN
0
120
2600MSPS
fIN1 = 794.5MHz AT –7.0dBFS
fIN2 = 791.5MHz AT –7.0dBFS
SFDR = 79.154dBc
IMD3 (dBFS)
–20
SFDR (dBFS)
AMPLITUDE (dBFS)
60
SFDR (dBc)
40
–60
–80
–100
–80
–70
–60
–50
–40
AMPLITUDE (dBFS)
–30
–20
–10
11814-518
20
0
–90
–40
–120
0
200
400
600
800
1000
1200
FREQUENCY (MHz)
Figure 56. Two Tone FFT Plot at 2.6 GSPS AIN = 1807 MHz
Figure 53. Two Tone SFDR and IMD3 vs. Analog Input Amplitude at
2.6 GSPS at 730 MHz AIN
Rev. C | Page 25 of 72
1400
11814-511
SFDR/IMD3 (dB)
100
80
11814-514
N+6
MORE
N+5
N+4
N+3
N+2
N
–10
N+1
–20
N–1
–30
N–3
–40
N– 2
–50
AMPLITUDE (dBFS)
N–4
–60
N–5
–70
N–6
–80
MORE
0
11814-517
0
–90
0.5
AD9625
0
0.5
2600MSPS
fIN1 = 728.5MHz AT –7.0dBFS
fIN2 = 731.5MHz AT –7.0dBFS
SFDR = 78.362dBc
–20
0.4
0.3
0.2
–40
DNL (LSB)
AMPLITUDE (dBFS)
Data Sheet
–60
–80
0.1
0
–0.1
–0.2
–0.3
–100
200
400
600
800
1000
1200
1400
FREQUENCY (MHz)
–0.5
11814-510
0
0
4096
1.2
0.8
–40
INL (LSB)
0.4
–60
–80
0
–0.4
–100
–120
0
200
400
600
800
1000
1200
FREQUENCY (MHz)
1400
–1.2
Figure 58. Two Tone FFT Plot at 2.6 GSPS AIN = 230 MHz
0
1024
2048
3072
CODES
Figure 60. Integral Nonlinearity (INL) at 2.6 GSPS
Rev. C | Page 26 of 72
4096
11814-508
–0.8
11814-509
AMPLITUDE (dBFS)
3072
Figure 59. Differential Nonlinearity (DNL) at 2.6 GSPS
2600MSPS
fIN1 = 231.5MHz AT –7.0dBFS
fIN2 = 228.5MHz AT –7.0dBFS
SFDR = 78.117dBc
–20
2048
CODES
Figure 57. Two Tone FFT Plot at 2.6 GSPS AIN = 730 MHz
0
1024
11814-507
–0.4
–120
Data Sheet
AD9625
EQUIVALENT TEST CIRCUITS
DRVDD
VDD
0.6pF
15Ω
890nH
0.5pF
50Ω
0.2pF
DIVCLK
0.2pF
11814-010
VCM
11814-150
AIN
DRVDD
Figure 66. Equivalent DIVCLK Output Circuit (DRVDD)
Figure 61. Equivalent Analog Input Circuit
VDD
EMPHASIS/SWING
CONTROL (SPI)
VDD
DRVDD
DATA+
11814-011
OUTPUT
DRIVER
DRVDD
DRGND
DATA–
Figure 62. Equivalent SCLK Circuit
11814-400
SCLK
1kΩ
DRGND
DVDD
Figure 67. Digital Outputs
2kΩ
1kΩ
DVDD2
11814-012
2pF
DVDD2
Figure 63. Equivalent VMON Temperature Sensor Circuit (DVDD)
DVDD2
200Ω
SYNCINB+
200Ω
SYNCINB–
100Ω
AVDD
20kΩ
CLK+
AVDD
0.88V
20kΩ
11814-153
AVDD
CLK–
11814-013
Figure 68. Equivalent SYNCINB± Input
DRVDD
Figure 64. Equivalent Clock Input Circuit
ESD
PROTECTED
DVDD
DRVDD
1kΩ
SDIO
SDI
30kΩ
30kΩ
ESD
PROTECTED
1kΩ
11814-401
ESD
PROTECTED
CSB
SDO
Figure 69. Equivalent SDIO Circuit
11814-015
ESD
PROTECTED
AVDD
AVDD
Figure 65. Equivalent CSB/PWDN Input Circuit
20kΩ
20kΩ
SYSREF–
11814-014
SYSREF+
AVDD
0.9V
Figure 70. Equivalent SYSREF± Input Circuit
Rev. C | Page 27 of 72
AD9625
Data Sheet
THEORY OF OPERATION
The FD bit is set when the absolute value of the input signal
exceeds the programmable upper threshold level. The FD bit
clears only when the absolute value of the input signal drops
below the lower threshold level for greater than the programmable
dwell time, thereby providing hysteresis and preventing the FD
bit from excessive toggling.
ADC ARCHITECTURE
The AD9625 is a pipelined ADC. The pipelined architecture
permits the first stage to operate on a new input sample and the
remaining stages to operate on the preceding samples. Sampling
occurs on the rising edge of the clock.
Each stage of the pipeline, excluding the last, consists of a low
resolution flash ADC connected to a switched capacitor digitalto-analog converter (DAC) and an interstage residue amplifier
(MDAC). The residue amplifier magnifies the difference between
the reconstructed DAC output and the flash input for the next
stage in the pipeline. One bit of redundancy is used in each stage
to facilitate digital correction of flash errors. The last stage simply
consists of a flash ADC.
GAIN THRESHOLD OPERATION
For best performance, the AD9625 needs an input signal to
perform internal calibration. This signal needs to exceed a set
threshold that is established through register settings. The
threshold prohibits background calibration updates for small
signal amplitudes. The threshold for gain calibration is enabled
by default.
Threshold Operation
The input stage contains a differential sampling circuit that can
be ac- or dc-coupled in differential or single-ended modes. The
output staging block aligns the data, corrects errors, and passes
the data to the output buffers. The output buffers are powered
from a separate supply, allowing adjustment of the output drive
current.
The absolute value of every sample is accumulated to produce
an average voltage estimate.
When the calibration has run for its predetermined number of
samples, the voltage estimate is compared to the data set threshold.
If the voltage estimate is greater than the threshold, the calibration coefficients update; otherwise, no update occurs.
Synchronization capability is provided to allow synchronized
timing between multiple devices.
Threshold Format
FAST DETECT
The threshold registers are all 16-bit registers loaded via the SPI
one byte at a time. The threshold values range from 0 to 16,384,
corresponding to a voltage range of 0.0 V to 1.2 V (full scale).
The fast detect block within the AD9625 generates a fast
detection bit (FD), which, when used with variable gain
amplifier front-end blocks, reduces the gain and prevents the
ADC input signal levels from exceeding the converter range.
The calibration threshold range is 0 to 16,384 (0x00 to 0x4000,
hexadecimal) and represents the average magnitude of the
input. For example, to set the threshold so that a −6 dBFS input
sine wave sits precisely at the threshold requires a threshold
setting of
Figure 71 shows the rapidity by which the detection bit is
programmable using an upper threshold, lower threshold,
and dwell time.
6
16,384 × 10 20 × 2 ≥ 5228

UPPER THRESHOLD
DWELL TIME
TIMER RESET BY
RISE ABOVE LT
DWELL TIME
FD
Figure 71. Fast Detection Bit
Rev. C | Page 28 of 72
TIMER COMPLETES BEFORE
SIGNAL RISES ABOVE LT
11814-016
LOWER THRESHOLD
Data Sheet
AD9625
TEST MODES
ADC TEST PATTERNS
12 BIT
SPI REGISTER 0x00D
BITS[3:0] ≠ 0000
JESD204B TEST PATTERNS
10 BIT
SPI REGISTER 0x061
BITS[5:4] = 01 AND
BITS[3:0] ≠ 0000
JESD204B
TEST PATTERNS
16 BIT
SPI REGISTER 0x061
BITS[5:4] = 00
AND BITS[3:0] ≠ 0000
SERALIZER
JESD204B
SAMPLE
CONSTRUCTION
ADC CORE
FRAME
CONSTRUCTION
SCRAMBLER
(OPTIONAL)
8b/10b
ENCODER
OUTPUT
11814-018
FRAMER
TAIL
BITS
Figure 72. Test Modes
Table 10. Flexible Output Test Modes from SPI Register 0x00D
Output Test
Mode Bit
Sequence
0000
0001
0010
0011
0100
0101
0111
1000
Pattern Name
Off (default)
Midscale short
Positive full scale
Negative full scale
Alternating checkerboard
PN sequence long
One-/zero-word toggle
User test mode
1111
Ramp output
Digital Output Word 1
(Default Twos Complement
Format)
Not applicable
0000 0000 0000
0111 1111 1111
1000 0000 0000
1010 1010 1010
Not applicable
1111 1111 1111
User data from
Register 0x019 to
Register 0x020
N
Rev. C | Page 29 of 72
Digital Output Word 2 (Default Twos
Complement Format)
Not applicable
= Word 1
= Word 1
= Word 1
0101 0101 0101
Not applicable
0000 0000 0000
User data from Register 0x019 to
Register 0x020
N+1
Subject to
Data Format
Select
Yes
Yes
Yes
Yes
No
Yes
No
Yes
No
AD9625
Data Sheet
ANALOG INPUT CONSIDERATIONS
AVDD
ANALOG
INPUT
Small series resistors (R3 and R4) limit input bandwidth, but can
be installed to further improve performance. Choose the input
network components such that its equivalent impedance, in
parallel with the 100 Ω input impedance of the AD9625, is
matched to the output impedance of the balun or amplifier.
Using a larger value for R3 and R4 suppresses the input
kickback from the sampling capacitor seen at the input to the
AD9625. However, the tradeoff is a lower usable input
bandwidth and an increase in the amount of signal power
needed to drive into the network for the AD9625 to sample a
full-scale signal.
Series isolation resistors (R5 and R6) are recommended to
reduce bandwidth peaking and minimize kickback from the
ADC sampling capacitor. Table 11 lists the front-end
requirements.
R3
DRVDD
R5
R1
AD9625
R2
R4
R6
VCM
11814-024
0.1µF
AD9625
50Ω
0.1µF
0.1µF
33Ω
1.5pF
ADC INTERNAL
INPUT Z
VCM
11814-359
INPUT
Z = 50Ω
Figure 74. Input Network Example for Passive Balun with High Bandwidth
25Ω
33Ω
33Ω
0.1µF 33Ω
0.1µF
AD9625
100Ω
INTERNAL
11814-360
EXTERNAL
BALUN/AMP
25Ω
Figure 75. Input Network Example for Passive Balun and >2 GHz ADC
Bandwidth
0.1µF 25Ω
EXTERNAL
BALUN/AMP
33Ω
33Ω
33Ω
0.1µF 25Ω
0.1µF
33Ω
AD9625
100Ω
INTERNAL
Figure 76. Input Network Example for Passive Balun and <2 GHz ADC
Bandwidth
USING THE ADA4961
As an alternative to using only a passive differential balun input
for wideband applications, the ADA4961 differential amplifier
driver can be used (see Figure 80).
The ADA4961 is a high performance BiCMOS RF differential
gain amplifier (DGA) optimized for driving heavy loads out to
2.0 GHz and beyond. It typically achieves −90 dBc IMD3
performance at 500 MHz and −85 dBc at 1.5 GHz. The device
also exhibits very low output noise (6.8 nV/√Hz). Together,
these performance numbers result in an SFDR of 133 dB/Hz
at 1.5 GHz.
The ADA4961 has an internal differential input impedance of
100 Ω and a differential dynamic output impedance of 50 Ω,
eliminating the need for external termination resistors. The
digital adjustability provides for 1 dB resolution, thus
optimizing SNR for input levels spanning 21 dB.
Figure 73. Recommended Front-End Network
Table 11. Recommended Front-End Components
Component
R1
R2
R3
R4
R5
R6
33Ω
100Ω
0.1µF 33Ω
Optimum performance is achieved while driving the AD9625
in a differential input configuration. A passive input configuration can be used with a single to differential balun at the analog
input to the AD9625. Because the AD9625 does not make use
of an internal input buffer, an external network needs to be
designed to reduce bandwidth peaking and minimize kickback
from the ADC sampling capacitor.
AVDD
0.1µF
50Ω
DIFFERENTIAL INPUT CONFIGURATIONS
0.1µF
0.1µF
DRVDD
11814-361
The AD9625 has a differential analog input, which is optimized
to provide superior wideband performance and must be driven
differentially. For best dynamic performance, the source
impedances driving VIN+ and VIN− should be matched such
that common-mode settling errors are symmetrical. Mismatch
between VIN+ and VIN− introduces undesired distortion. A
wideband transformer, balun, or amplifier can provide the
differential analog inputs for applications that require a singleended to differential conversion.
Component Value
33 Ω to 50 Ω (termination)
33 Ω to 50 Ω (termination)
0 Ω to 33 Ω (lower for higher bandwidth)
0 Ω to 33 Ω (lower for higher bandwidth)
33 Ω
33 Ω
Rev. C | Page 30 of 72
Data Sheet
AD9625
The two-tone 1 GHz IMD of two 0.55 V p-p signals have an
SFDR of greater than 75 dBc, as shown in Figure 78.
Figure 80 uses a 1:2 impedance transformer to provide the
100 Ω input impedance of the ADA4961 with a matched input.
The open collector outputs of the ADA4961 are biased through
the two 560 nH inductors. The two 0.1 μF capacitors on the
outputs decouple the 5 V inductor voltage from the input
common-mode voltage of the ADA4961. The two 50 Ω
resistors in parallel with the 100 Ω input impedance of the
AD9625 provide the 50 Ω load to the ADA4961, whose gain
is load dependent. The 2 nH inductors and the 1.5 pF internal
capacitance of the AD9625 constitute a 1 GHz low-pass filter to
−1 dB. The two 10 Ω isolation resistors suppress any switching
currents from the AD9625 sample-and-hold circuitry. The
circuit depicted in Figure 80 provides variable gain, isolation,
filtering and source matching for the AD9625. By using this
circuit with the ADA4961 in a gain of 15 dB (maximum gain)
an SNRFS of 55 dB and an SFDR performance of 77 dBc are
achieved with a 1 GHz input as shown in Figure 80.
0
2500MSPS
fIN1 = 1022.3MHz AT –7.0dBFS
fIN2 = 1012.3MHz AT –7.0dBFS
SFDR = 75.8dBc
AMPLITUDE (dBFS)
–20
–40
–60
–80
2F1 + F2
F1 + F2
2F2 + F1
F2 – F1
2F1 – F2
2F2 – F1
–120
0
150
300
450
600
750
900
FREQUENCY (MHz)
1050
1200
11814-364
–100
Figure 78. Measured Two-Tone Performance of the Circuit Shown in
Figure 80 for a 1 GHz input Signal Using Maximum Gain (15 dB)
10
2500MSPS
1003.8MHz AT –1.0dBFS
SNR = 53.83dB
SFDR = 77.354dBc
–20
5
0
–40
AMPLITUDE (dB)
–60
23
–80
46
5
+
–5
–10
–15
–100
150
300
450
600
750
900
1050
11814-363
0
1200
FREQUENCY (MHz)
–25
10
Figure 77. Measured Single-Tone Performance of the Circuit Shown in
Figure 80 for a 1 GHz Input Signal Using Maximum Gain (15 dB)
100
1000
10000
FREQUENCY (MHz)
Figure 79. Measured Frequency Response of the AD9625 Interface with
ADA4961 Depicted in Figure 80
5.0V
0.5nH
MARKI
5.0V
BAL-0006GSMG
1:2
0.1µF
BANDPASS
FILTER
0.1µF
2nH
10Ω VIN+
50Ω
50Ω
ADA4961
1.5pF
50Ω
AC
0.1µF
AD9625
+
100Ω
2nH
0.1µF
10Ω VIN–
VCM
0.5nH
DIGITAL
INTERFACE
5.0V
Figure 80. Configuration for Driving the AD9625 with ADA4961
Rev. C | Page 31 of 72
11814-365
–20
–120
11814-362
AMPLITUDE (dBFS)
0
AD9625
Data Sheet
DC COUPLING
The AD9625 can operate using a dc-coupled input configuration. The differential analog common-mode input signal would
need to be referenced to the VCM output of the AD9625.
CLOCK INPUT CONSIDERATIONS
For optimum performance, drive the AD9625 sample clock
inputs (CLK+ and CLK−) with a differential signal. This
signal is typically ac-coupled to the CLK+ and CLK− pins via a
transformer or capacitors. These pins are biased internally and
require no additional biasing.
Clock Jitter Considerations
High speed, high resolution ADCs are sensitive to the quality of the
clock input. The degradation in SNR at a given input frequency
(fA) due only to aperture jitter (tJ) can be calculated by
SNR = 20 × log 10(1/(2 × π × fA × tJ))
In cases where aperture jitter may affect the dynamic range of
the AD9625, treat the clock input as an analog signal. To avoid
modulating the clock signal with digital noise, separate power
supplies for clock drivers from the ADC output driver supplies.
Low jitter, crystal-controlled oscillators make the best clock
sources. If the clock is generated from another type of source (by
gating, dividing, or other methods), it should be retimed by the
original clock at the last step. Refer to the AN-501 Application
Note and the AN-756 Application Note for more information
about jitter performance as it relates to ADCs.
Clock Duty Cycle Considerations
Typical high speed ADCs use both clock edges to generate a
variety of internal timing signals. As a result, these ADCs may
be sensitive to clock duty cycle. Commonly, a 5% tolerance is
required on the clock duty cycle to maintain dynamic performance
characteristics.
In this equation, the rms aperture jitter represents the rootmean-square of all jitter sources, including the clock input,
analog input signal, and ADC aperture jitter specifications. IF
undersampling applications are particularly sensitive to jitter
(see Figure 81).
130
12.5fS
25fS
50fS
100fS
200fS
400fS
800fS
120
110
90
80
70
60
50
40
30
10
100
1000
10000
ANALOG INPUT FREQUENCY (MHz)
11814-366
SNR (dB)
100
Figure 81. Ideal SNR vs. Analog Input Frequency and Jitter
Rev. C | Page 32 of 72
Data Sheet
AD9625
DIGITAL DOWNCONVERTERS (DDC)
MODE SELECT:
96MHz OR 192MHz BW
I-PHASE
NCO
MIXER
8 × 13-BIT
@ 250MHz
SYNTHESIZER
TUNER SELECT:
–1.0GHz TO +1.0GHz
8 × 12-BIT
@ 250MHz
MIXER
16-BIT @ 250MHz
DECIMATION
BY 8
16-BIT
@ 125MHz
GAIN SELECT:
0dB, 6dB, 12dB, 18dB
8 × 13-BIT
@ 250MHz
DECIMATION
BY 2
GAIN SELECT:
0dB, 6dB,
12dB, 18dB
DECIMATION
BY 8
TO
FRAMER
16-BIT
@ 125MHz
TO
FRAMER
16-BIT @ 250MHz
Q-PHASE
11814-019
12-BIT ADC
@ 2.0GSPS
8 × 12-BIT
@ 250MHz
Figure 82. Digital Downconverter Block Diagram Operating at 2.0 GSPS
The AD9625 architecture includes two DDCs, each designed to
extract a portion of the full digital spectrum captured by the
ADC. Each tuner consists of an independent frequency synthesizer
and quadrature mixer; a chain of low-pass filters for rate conversion
follows these components. Assuming a sampling frequency of
2.500 GSPS, the frequency synthesizer (10-bit NCO) allows for
1024 discrete tuning frequencies, ranging from −1.2499 GHz to
+1.2500 GHz, in steps of 2500/1024 = 2.44 MHz. The low-pass
filters allow for two modes of decimation.
FREQUENCY SYNTHESIZER AND MIXER

A high bandwidth mode, 240 MHz wide (from −120 MHz
to +120 MHz), sampled at 2.5 GHz/8 = 312.5 MHz for the
I and Q branches separately. The 16-bit samples from the I
and Q branches are transmitted through a dedicated
JESD204B interface.
A low bandwidth mode, 120 MHz wide (from −60 MHz to
+60 MHz), sampled at 2.5 GHz/16 = 156.25 MHz for the I
and Q branches separately. The 16-bit samples from the I
and Q branches are transmitted through a dedicated
JESD204B interface.
Each DDC has a 10-bit oscillator that is synthesized and mixed
with the ADC output data. The 10-bit phase can be tuned for
each DDC based on the value used in its NCO registers. The
phase for DDC0 is located with Register 0x132 and Register 0x131.
The phase for DDC1 is located with Register 0x13A and
Register 0x139. The NCO output frequency for DDC0 =
(decimal(Register 0x132[1:0]; Register 0x131[7:0]) × fS)/1024. The
NCO output frequency for DDC1 = (decimal(Register 0x13A[1:0];
Register 0x139[7:0]) × fS)/1024.
By design, all of the blocks operate at a single clock frequency of
2.5 GHz/8 = 312.5 MHz.
The first filter stage is designed for a rate reduction factor of 8,
yielding a sample rate of 2.500 GHz/8 = 312.5 MHz. To achieve
a combination of low complexity and low clock rate, the DDC
employs a decimate-by-8 polyphase fuse filter that receives
eight 13-bit samples from the mixer block at every clock cycle.

Each filter stage includes a gain control block that is programmable
by the user. The gain varies from 0 dB to 18 dB, in steps of 6 dB,
and the gain is applied before final scaling and rounding. The
gain control feature may be useful in cases where the tuner
filters out a strong out-of-band interferer, leaving a weak
in-band signal.
For a sampling rate of 2.500 GHz, the synthesizer (10-bit
NCO) outputs one of 1024 possible complex frequencies from
−1.249 GHz to +1.250 GHz. The synthesizer employs the direct
digital synthesis technique, using look-up sine tables and a
phase accumulator. The user specifies the tuner frequency by
writing to a 10-bit phase increment register.
NUMERICALLY CONTROLLED OSCILLATOR
HIGH BANDWIDTH DECIMATOR
The block design provides user specified gain control, from 0 dB to
18 dB in steps of 6 dB. The gain is applied before final scaling
and rounding to 16 bits.
Rev. C | Page 33 of 72
AD9625
Data Sheet
10
Table 12. Filter Tap Coefficients for High Bandwidth
Decimator
0
–10
MAGNITUDE (dB)
–20
–30
–40
–50
–60
–70
–80
–100
fS/2
FREQUENCY (MHz)
11814-020
–90
Figure 83. Magnitude Response of the Decimate-by-8 Polyphase Fuse Filter
Filter performance is shown in Figure 83 and Figure 84. The
filter yields an effective bandwidth of 120 MHz, with a transition
band of 156.5 MHz − 120 MHz = 36.5 MHz. Therefore, the
two-sided complex bandwidth of the filter is 240 MHz.
A rejection ratio of 85 dB ensures that the seven aliases that fold
back into the pass band yield an SNR of 85 dB − 10log10(7) =
76.5 dB, which ensures that the aliases remain sufficiently below
the noise floor of the input signal. The pass-band ripple is
±0.05 dB, as shown in Figure 84.
0.25
0.20
MAGNITUDE (dB)
0.15
0.10
0.05
0
–0.05
–0.10
–0.15
0
20
40
60
80
100
120
FREQUENCY (MHz)
11814-021
–0.20
Figure 84. Magnitude Ripple in the High Bandwidth Pass Band
The high bandwidth decimator has a filter architecture that
consists of a 142 tap delay line. The coefficients are 17 bits each
and are listed in Table 12.
Tap Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
Rev. C | Page 34 of 72
Coefficient
−38
−57
−92
−132
−172
−204
−219
−207
−162
−79
+43
+196
+369
+540
+685
+780
+800
+727
+554
+289
−48
−420
−778
−1069
−1238
−1242
−1055
−677
−135
+513
+1186
+1785
+2210
+2372
+2209
+1698
+869
−200
−1382
−2516
−3425
−3945
−3944
−3353
−2179
−519
+1446
+3467
+5250
+6496
+6945
Data Sheet
Tap Number
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
AD9625
Coefficient
+6412
+4831
+2276
−1031
−4725
−8330
−11304
−13098
−13222
−11306
−7160
−808
+7498
+17281
+27882
+38515
+48340
+56550
+62451
+65536
+65536
+62451
+56550
+48340
+38515
+27882
+17281
+7498
−808
−7160
−11306
−13222
−13098
−11304
−8330
−4725
−1031
+2276
+4831
+6412
+6945
+6496
+5250
+3467
+1446
−519
−2179
−3353
−3944
−3945
−3425
−2516
−1382
Tap Number
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
Rev. C | Page 35 of 72
Coefficient
−200
+869
+1698
+2209
+2372
+2210
+1785
+1186
+513
−135
−677
−1055
−1242
−1238
−1069
−778
−420
−48
+289
+554
+727
+800
+780
+685
+540
+369
+196
+43
−79
−162
−207
−219
−204
−172
−132
−92
−57
−38
AD9625
Data Sheet
LOW BANDWIDTH DECIMATOR
Use the second filter stage in the optional low bandwidth mode
only. It achieves an additional rate reduction factor of 2, yielding a
final sample rate of 2.500 GHz/16 = 156.25 MHz. The internal
architecture of the low bandwidth decimation filter is similar to
that of a high bandwidth decimator. Moreover, for ease of
physical design, the block operates at 312.5 MHz, a result of
which both the I- and Q-phases can share the filter engine.
The performance of the low bandwidth decimation filter is
shown in Figure 85 and Figure 86. The filter yields an effective
bandwidth of 60 MHz, with a transition band of 81.25 MHz −
60 MHz = 21.25 MHz. Thus, the two sided, complex bandwidth
of the filter is 120 MHz. A rejection ratio of 85 dB ensures that
the alias region folds back well below the noise floor of the
input signal.
As with the high bandwidth filter, this block provides user
specified gain control, from 0 dB to 18 dB, in steps of 6 dB. The
gain is applied before final quantization at the output of the low
bandwidth decimation filter to 16 bits.
10
0
–10
MAGNITUDE (dB)
–20
–30
–40
–50
–60
–70
–80
–100
0
20
40
60
80
100
120
140
160
FREQUENCY (MHz)
11814-022
–90
Figure 85. Magnitude Response of Decimate-by-2 Filter
0.4
The low bandwidth decimator has a filter architecture that
consists of a 31 tap delay line. The coefficients are 17 bits each
and are listed in Table 13.
Table 13. Filter Tap Coefficients for Low Bandwidth
Decimator
Tap Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
0.2
0.1
0
–0.1
–0.2
0
10
20
30
40
50
60
FREQUENCY (MHz)
11814-023
MAGNITUDE (dB)
0.3
Figure 86. Magnitude Ripple in the Low Bandwidth Pass Band
Rev. C | Page 36 of 72
Coefficient
+126
+312
−16
−859
−628
+1217
+1428
−1944
−3227
+2511
+6302
−3099
−13075
+3441
+43442
+65536
+43442
+3441
−13075
−3099
+6302
+2511
−3227
−1944
+1428
+1217
−628
−859
−16
+312
+126
Data Sheet
AD9625
DIGITAL OUTPUTS
INTRODUCTION TO THE JESD204B INTERFACE
The AD9625 digital output complies with the JEDEC Standard
No. JESD204B, Serial Interface for Data Converters. JESD204B is
a protocol to link the AD9625 to a digital processing device
over a serial interface up to and above 6.5 Gbps link speeds. The
benefits of the JESD204B interface over LVDS include a reduction
in required board area for data interface routing, and enabling
smaller packages for converter and logic devices. The AD9625
supports one, two, four, six, or eight output lanes.
The JESD204B data transmit block assembles the parallel data
from the ADC into frames and uses 8-bit/10-bit encoding as
well as optional scrambling to form serial output data. Lane
synchronization is supported using special characters during
the initial establishment of the link. Additional data that is used
to maintain synchronization is embedded in the data stream
thereafter. A JESD204B receiver is required to complete the
serial link. For additional details on the JESD204B interface,
users are encouraged to refer to the JESD204B standard.
Table 14 describes the JESD204B interface nomenclature (the
terms, converter device and link, are used interchangeably in
the specification).
Table 14. JESD204B Interface Nomenclature
Symbol
S
M
L
N
N'
CF
CS
K
HD
F
C
T
Description
Samples transmitted per single converter per frame cycle
Number of converters per converter device (link)
Number of lanes per converter device (link)
Converter resolution
Total number of bits per sample
Number of control words per frame clock cycle per
converter device (link)
Number of control bits per conversion sample
Number of frames per multiframe
High density mode
Octets per frame
Control bit (overrange, timestamp)
Tail bit
TRANSPORT
LAYER
PROCESSED
SAMPLES
FROM ADC
SAMPLE
CONSTRUCTION
FRAME
CONSTRUCTION






M = 1 (single converter, always for AD9625)
L = 1 to 8 (up to eight lanes)
S = 4 (four samples per JESD204B frame)
F = 1, 2, 4, 8 (up to 8 octets per frame)
N’ = 12, 16 (12- or 16-bit JESD204B word size)
HD = 0, 1 (high density mode, sample span multiple lanes)
FUNCTIONAL OVERVIEW
The block diagram in Figure 87 shows the flow of data through
the JESD204B hardware from the sample input to the physical
output. The processing can be divided into layers that are
derived from the OSI model widely used to describe the
abstraction layers of communications systems. These are the
transport layer, data link layer, and physical layer (serializer).
Each of these layers are described in detail in the following
sections.
Transport Layer
The transport layer handles packing the data (consisting of
samples and optional control bits) into 8-bit words that are sent
to the data link layer. The transport layer is controlled by rules
derived from the link configuration data. It packs data according to
the rules, adding tail bits to fill gaps when required.
Data Link Layer
The data link layer is responsible for the low level functions of
passing data across the link. These include optionally scrambling
the data, handling the synchronization process for characters,
frames, and lanes across the links, encoding 8-bit data-words
into 10-bit characters, and inserting appropriate control
characters into the data output. The data link layer is also
responsible for sending the initial lane alignment sequence
(ILAS), which contains the link configuration data, used by
the receiver (Rx) to verify the settings in the transport layer.
Physical Layer
The physical layer consists of the high speed circuitry clocked at
the serial clock rate. The physical layer includes the serialization
circuits and the high speed drivers.
DATA LINK
LAYER
SCRAMBLER
ALIGNMENT
CHARACTER
GENERATION
Figure 87. Data Flow
Rev. C | Page 37 of 72
8-BIT/10-BIT
ENCODER
PHYSICAL
LAYER
CROSSBAR
MUX
SERIALIZER
OUTPUT
11814-242
The AD9625 JESD204B transmit block maps to two digital
down converters for the outputs of the ADC over a link. A
link can be configured to use up to eight JESD204B lanes.
The JESD204B specification refers to a number of parameters
to define the link, and these parameters must match between
the JESD204B transmitter (AD9625 output) and receiver
(FPGA, ASIC, or logic device).
The AD9625 adheres to the JESD204B draft specification,
which provides a high speed, serial, embedded clock interface
standard for data converters and logic devices. It is designed as
an MCDA-ML, Subclass 1 device that uses the SYSREF± input
signal for multichip synchronization and deterministic latency.
This design adheres to the following basic JESD204B link configuration parameters:
AD9625
Data Sheet
JESD204B INTERFACE
M = 1; L = 8; N = 12; N' = 16; CF = 0; CS = 0; CS = 0...4; K = 32; HD = 1; F = 1
400ps MIN (2.5GHz)
CLK+
(ENCODE CLOCK)
f g h
i
j a
b
F = 1 OCTETS
F = 1 OCTETS
F = 1 OCTETS
SAMPLE N [11:4]
SAMPLE N + 4 [11:4]
SAMPLE N + 8 [11:4]
SAMPLE N + 12 [11:4]
c d
e
f g h
i
j
a
SAMPLE N [3:0],
CTTTT
LANE B±
@ 6.25Gbps
f g h
i
j a
b
c d
e
f g h
f g h
i
j a
b
c d
e
f g h
i
j
a
f g h
i
j a
b
c d
e
f g h
i
j
a
f g h
i
j a
b
c d
e
f g h
i
j
a
f g h
i
j a
b
c d
e
f g h
i
j
a
f g h
i
j a
b
c d
e
f g h
i
j
a
i
f g h
i
j a
b
c d
e
f g h
i
b
c d
e
f g h
i
b
c d
e
f g h
i
b
c d
e
f g h
i
b
c d
e
f g h
i
b
c d
e
f g h
i
j
a
b
c d
e
f g h
i
j a
a
b
c d
e
f g h
i
c d
b
c d
j a
b
c d
f g h
i
j
a
e
f g h
i
e
f g h
i
j a
b
c d
e
f g h
i
j
a
b
c d
e
f g h
i
j
a
b
c d
e
f g h
i
j
a
b
c d
e
f g h
i
j
a
b
c d
e
f g h
i
i
j
b
c d
e
f g h
i
j
b
c d
e
f g h
i
j
b
c d
e
f g h
i
j
b
c d
e
f g h
i
j
SAMPLE N + 14 [3:0],
CTTTT
j
a
b
c d
e
f g h
i
j
SAMPLE N + 15 [11:4]
j
a
SAMPLE N + 11 [3:0],
CTTTT
j a
f g h
SAMPLE N + 14 [11:4]
SAMPLE N + 11 [11:4]
j a
e
SAMPLE N + 13 [3:0],
CTTTT
SAMPLE N + 10 [3:0],
CTTTT
j a
c d
SAMPLE N + 13 [11:4]
SAMPLE N + 10 [11:4]
j a
b
SAMPLE N + 12 [3:0],
CTTTT
SAMPLE N + 9 [3:0],
CTTTT
Figure 88. JESD204B Lane Data Mapping
Rev. C | Page 38 of 72
e
SAMPLE N + 9 [11:4]
SAMPLE N + 7 [3:0],
CTTTT
j
b
SAMPLE N + 8 [3:0],
CTTTT
SAMPLE N + 7 [11:4]
SAMPLE N + 3 [3:0],
CTTTT
LANE H±
@ 6.25Gbps
j a
SAMPLE N + 6 [3:0],
CTTTT
SAMPLE N + 3 [11:4]
LANE G±
@ 6.25Gbps
i
SAMPLE N + 6 [11:4]
SAMPLE N + 2 [3:0],
CTTTT
LANE F±
@ 6.25Gbps
f g h
SAMPLE N + 5 [3:0],
CTTTT
SAMPLE N + 2 [11:4]
LANE E±
@ 6.25Gbps
e
SAMPLE N + 5 [11:4]
SAMPLE N + 1 [3:0],
CTTTT
LANE D±
@ 6.25Gbps
c d
SAMPLE N + 4 [3:0],
CTTTT
SAMPLE N + 1 [11:4]
LANE C±
@ 6.25Gbps
b
b
c d
e
f g h
i
j
SAMPLE N + 15 [3:0],
CTTTT
j
a
b
c d
e
f g h
i
j
11814-373
LANE A±
@ 6.25Gbps
F = 1 OCTETS
Data Sheet
AD9625
JESD204B LINK ESTABLISHMENT
Data Streaming
The AD9625 JESD204B Tx interface operates in Subclass 1 as
defined in the JEDEC Standard No. 204B-July 2011 specification.
It is divided into the following steps: code group synchronization,
initial lane alignment sequence, and data streaming.
After the initial lane alignment sequence is complete, the user
data is sent. In a usual frame, all characters are user data.
However, to monitor the frame clock and multiframe clock
synchronization, there is a mechanism for replacing characters
with /F/ or /A/ alignment characters when the data meets
certain conditions. These conditions are different for unscrambled
and scrambled data. The scrambling operation is enabled by
default but may be disabled using SPI.
Code Group Synchronization (CGS) and SYNCINB±
CGS is the process where the JESD204B receiver finds the
boundaries between the 10-bit characters in the stream of data.
During the CGS phase, the JESD204B transmit block transmits
/K28.5/ characters. The receiver (external logic device) must
locate the /K28.5/ characters in its input data stream using clock
and data recovery (CDR) techniques.
The receiver issues a synchronization request by activating the
SYNCINB± pins of the AD9625. The JESD204B Tx begins
sending /K28.5/ characters until the next LMFC boundary.
When the receiver has synchronized, it waits for the correct
reception of at least four consecutive /K28.5/ symbols. It then
deactivates SYNCINB±. The AD9625 then transmits an initial
lane alignment sequence (ILAS) on the following LMFC
boundary.
For more information on the code group synchronization
phase, refer to the JEDEC Standard No. 204B-July 2011, Section
5.3.3.1.
The SYNCINB± pin operation can be controlled by SPI. The
SYNCINB± signal is a differential LVDS mode signal by default,
but it can also be driven single ended. For more information on
configuring the SYNCINB± pin operation, refer to the Memory
Map section.
Initial Lane Alignment Sequence (ILAS)
The ILAS phase follows the CGS phase and begins on the next
LMFC boundary. The ILAS consists of four mulitframes, with
an /R/ character marking the beginning and an /A/ character
marking the end. The ILAS begins by sending an /R/ character
followed by 0 to 255 ramp data for one multiframe. On the
second multiframe, the link configuration data is sent starting
with the third character. The second character is a /Q/ character
to confirm that the link configuration data follows. All
undefined data slots are filled with ramp data. The ILAS
sequence is never scrambled.
The ILAS sequence construction is shown in Figure 90. The
four multiframes include the following:




Multiframe 1: begins with an /R/ character (K28.0) and
ends with an /A/ character (K28.3).
Multiframe 2: begins with an /R/ character followed by a
/Q/ [K28.4] character, followed by link configuration
parameters over 14 configuration octets and ends with an /A/
character. Many of the parameter values are of the notation of
the value, −1.
Multiframe 3: this is the same as Multiframe 1.
Multiframe 4: this is the same as Multiframe 1.
For scrambled data, any 0xFC character at the end of a frame is
replaced by an /F/, and any 0x7C character at the end of a
multiframe is replaced with an /A/. The JESD204B Rx checks
for /F/ and /A/ characters in the received data stream and
verifies that they only occur in the expected locations. If an
unexpected /F/ or /A/ character is found, the receiver handles
the situation by using dynamic realignment or activating the
SYNCINB± signal for more than four frames to initiate a
resynchronization. For unscrambled data, if the final character
of two subsequent frames is equal, the second character is
replaced with an /F/ if it is at the end of a frame, and an /A/ if it
is at the end of a multiframe.
Insertion of alignment characters may be modified using SPI.
The frame alignment character insertion is enabled by default.
More information on the link controls is available in the
Memory Map section, Register 0x062.
Link Setup Parameters
The following steps demonstrate how to configure the AD9625
JESD204B interface and the output:
1.
2.
3.
4.
5.
6.
7.
Disable the lanes before changing configuration.
Select one quick configuration option.
Configure the detailed options.
Check FCHK, checksum of JESD204B interface parameters.
Set additional digital output configuration options.
Reenable the required lane(s).
Before modifying the JESD204B link parameters, disable
the link and hold it in reset.
8-Bit/10-Bit Encoder
The 8-bit/10-bit encoder converts 8-bit octets into 10-bit
characters and inserts control characters into the stream when
needed. The control characters used in JESD204B are shown in
Table 15. The 8-bit/10-bit encoding allows the signal to be dc
balanced by using the same number of ones and zeros.
The 8-bit/10-bit interface has options that may be controlled via
SPI. These operations include bypass, invert or mirror. These
options are intended to be a troubleshooting tool for the
verification of the digital front end (DFE).
Rev. C | Page 39 of 72
AD9625
Data Sheet
Digital Outputs, Timing, and Controls
VRXCM
The AD9625 physical layer consists of drivers that are defined in
the JEDEC Standard No. 204B-July 2011. The differential digital
outputs are powered up by default. The drivers utilize a
dynamic 100 Ω internal termination to reduce unwanted
reflections.
DRVDD
R
D
D
A
R
Q
C
C
D
D
OR
100Ω
RECEIVER
0.1µF
OUTPUT SWING = 300mV p-p
11814-243
SERDOUT[x]–
VCM = VRXCM
Figure 89. AC-Coupled Digital Output Termination Example
If there is no far end receiver termination, or if there is poor
differential trace routing, timing errors may result. To avoid
such timing errors, it is recommended that the trace length be
less than six inches, and that the differential output traces be
close together and at equal lengths.
The AD9625 digital outputs can interface with custom ASICs
and FPGA receivers, providing superior switching performance
in noisy environments. Single point-to-point network topologies
are recommended with a single differential 100 Ω termination
resistor placed as close to the receiver inputs as possible.
K
50Ω
SERDOUT[x]+
Place a 100 Ω differential termination resistor at each receiver
input to result in a nominal 300 mV p-p swing at the receiver
(see Figure 89). Alternatively, single-ended 50 Ω termination
can be used. When single-ended termination is used, the termination voltage should be DRVDD/2; otherwise, 0.1 μF ac coupling
capacitors can be used to terminate to any single-ended voltage.
K
50Ω
100Ω
DIFFERENTIAL
0.1µF TRACE PAIR
De-Emphasis
De-emphasis enables the receiver eye diagram mask to be met
in conditions where the interconnect insertion loss does not
meet the JESD204B specification. The de-emphasis feature
should only be used when the receiver is unable to recover the
clock due to excessive insertion loss. Under normal conditions,
it is disabled to conserve power. Additionally, enabling and
setting too high a de-emphasis value on a short link may cause
the receiver eye diagram to fail. Using the de-emphasis setting
may increase EMI. See the Memory Map section for details.
A
R
D
D
A
R
D
D
A
D
START OF
ILAS
START OF LINK
CONFIGURATION
DATA
START OF
USER DATA
Figure 90. Initial Lane Alignment Sequence
Table 15. AD9625 Control Characters Used in JESD204B
Abbreviation
/R/
/A/
/Q/
/K/
/F/
Control Symbol
/K28.0/
/K28.3/
/K28.4/
/K28.5/
/K28.7/
8-Bit Value
000 11100
011 11100
100 11100
101 11100
111 11100
10-Bit Value
RD (Running
Disparity) = −1
001111 0100
001111 0011
001111 0010
001111 1010
001111 1000
Rev. C | Page 40 of 72
10-Bit Value
RD (Running
Disparity) = +1
110000 1011
110000 1100
110000 1101
110000 0101
110000 0111
Description
Start of multiframe
Lane alignment
Start of link configuration data
Group synchronization
Frame alignment
11814-132
END OF
MULTIFRAME
Data Sheet
AD9625
Table 16. JESD204B Mode of Operation (M = 1, S = 4, N' = 16, Unless Otherwise Noted)
Quick
Configuration
Value
0x02
0x04
0x06
0x08
0x42
0x44
0x48
0x81
0x82
0x91
0xC1
0xC2
0xC4
0xE1
0xE2
0xE4
0xD1
0xD2
1
Description1
Generic
Generic
Generic (N' = 12)
Generic
fS × 8
fS × 4
fS × 2
Single DDC, high BW
Single DDC, high BW
Single DDC, low BW
Dual DDC, high BW
Dual DDC, high BW
Dual DDC, high BW
Dual DDC, mixed BW
Dual DDC, mixed BW
Dual DDC, mixed BW
Dual DDC, low BW
Dual DDC, low BW
Lanes
(L)
2
4
6
Octets/
Frame (F)
4
2
1
Sample Clock Rate
Minimum Maximum
MSPS
MSPS
330
650
650
1300
1300
2500
Sample Clock
Multiplier
10
5
2.5
JESD204B Lane Rate
Minimum
Maximum
Mbps
Mbps
3300
6500
3250
6500
3250
6250
8
2
4
8
1
2
1
1
2
4
1
2
4
1
2
1
4
2
1
8
4
8
8
4
2
8
4
2
8
4
1300
406
813
1625
650
1300
1300
330
650
1300
330
650
1300
650
1300
2.5
8
4
2
5
2.5
2.5
10
5
2.5
10
5
2.5
5
2.5
3250
3250
3250
3250
3250
3250
3250
3300
3250
3250
3300
3250
3250
3250
3250
2500
813
1625
2500
1300
2500
2500
650
1300
2500
650
1300
2500
1300
2500
6250
6500
6500
5000
6500
6250
6250
6500
6500
6250
6500
6500
6250
6500
6250
DDC means digital downconverter, BW means bandwidth, fS × x means sample rate multiplied by an integer (where x is an integer: 2, 4, 8).
Table 17. JESD204B Logical Lane Mapping
Quick
Configuration
Value
0x02
0x04
0x06
0x08
0x42
0x44
0x48
Description
Generic
Generic
Generic
(N' = 12)
Generic
fS × 8
fS × 4
fS × 2
Lanes
(L)
2
4
6
8
2
4
8
0x81
Single DDC,
high BW
1
0x82
Single DDC,
high BW
Single DDC,
low BW
2
0xC1
Dual DDC,
high BW
1
0xC2
Dual DDC,
high BW
Dual DDC,
high BW
Dual DDC,
mixed BW
2
Dual DDC,
mixed BW
2
0x91
0xC4
0xE1
0xE2
1
4
1
Logical
Logical
Logical
Logical
Logical
Logical
Lane 0
Lane 1
Lane 2
Lane 3
Lane 4
Lane 5
S[N],
S[N + 2],
Off
Off
Off
Off
S[N + 1]
S[N + 3]
S[N]
S[N + 1]
S[N + 2]
S[N + 3]
Off
Off
SMSB[N], SLSB[N], SMSB[N + 1], SLSB[N + 1], SMSB[N + 2], SLSB[N + 2], SMSB[N + 3], SLSB[N + 3]
Logical
Lane 6
Off
Logical
Lane 7
Off
Off
Off
Off
Off
SMSB[N]
SLSB[N]
SMSB[N + 1]
SLSB[N + 1]
SMSB[N + 2]
SLSB[N + 2]
SMSB[N + 3]
SLSB[N + 3]
See Figure 104, fS × 2 mode application layer (transmit)
See Figure 104, fS × 2 mode application layer (transmit)
SMSB[N], SLSB[N], SMSB[N + 1], SLSB[N + 1], SMSB[N + 2], SLSB[N + 2], SMSB[N + 3], SLSB[N + 3], SMSB[N + 4], SLSB[N + 4];
see Figure 104, fS × 2 mode application layer (transmit)
Off
Off
Off
Off
Off
Off
Off
I0[N],
Q0[N],
I0[N + 1],
Q0[N + 1]
I0[N+1],
Off
Off
Off
Off
Off
Off
I0[N],
Q0[N]
Q0[N+1]
Off
Off
Off
Off
Off
Off
Off
I0[N],
Q0[N],
I0[N + 1],
Q0[N + 1]
Off
Off
Off
Off
Off
Off
Off
I0[N],
Q0[N],
I1[N],
Q1[N]
I0[N],
I1[N],
Off
Off
Off
Off
Off
Off
Q0[N]
Q1[N]
I0[N]
Q0[N]
I1[N]
Q1[N]
Off
Off
Off
Off
I0[N],
Q0[N],
I1[N],
Q1[N]
I0[N],
Q0[N]
Off
Off
Off
Off
Off
Off
Off
I1[N],
Q1[N]
Off
Off
Off
Off
Off
Off
Rev. C | Page 41 of 72
AD9625
Quick
Configuration
Value
0xE4
0xD1
0xD2
Data Sheet
Description
Dual DDC,
mixed BW
Dual DDC,
low BW
Dual DDC,
low BW
Lanes
(L)
4
Logical
Lane 0
I0[N]
Logical
Lane 1
Q0[N]
Logical
Lane 2
I1[N]
Logical
Lane 3
Q1[N]
Logical
Lane 4
Off
Logical
Lane 5
Off
Logical
Lane 6
Off
Logical
Lane 7
Off
1
I0[N],
Q0[N],
I1[N],
Q1[N]
I0[N],
Q0[N]
Off
Off
Off
Off
Off
Off
Off
I1[N],
Q1[N]
Off
Off
Off
Off
Off
Off
2
Table 18. Typical Current Consumption per ADC Mode (Unused Output Lanes are Powered Down)
Quick
Configuration
Value
0x02
0x04
0x06
0x08
0x42
0x44
0x48
0x81
0x82
0x91
0xC1
0xC2
0xC4
0xE1
0xE2
0xE4
0xD1
0xD2
Typical Current Consumption (A)
Mode
Generic, two lane
Lanes
(L)
2
Sample Rate
(MSPS)
650
IAVDD1
0.7
IAVDD2
0.3
IDRVDD1
0.2
IDRVDD2
0.0
IDVDD1
0.1
IDVDD2
0.0
Total Power (W)
2.1
Generic, four lane
Generic, six lane
Generic, eight lane
fS × 8
fS × 4
fS × 2
Single DDC high BW, one lane
Single DDC high BW, two lane
Single DDC low BW, one lane
Dual DDC high BW, one lane
Dual DDC high BW, two lane
Dual DDC high BW, four lane
Dual DDC mixed BW, one lane
Dual DDC mixed BW, two lane
Dual DDC mixed BW, four lane
Dual DDC low BW, one lane
Dual DDC low BW, two lane
4
6
8
2
4
8
1
2
1
1
2
4
1
2
4
1
2
1300
2600
2600
813
1625
2600
1300
2600
2600
650
1300
2600
650
1300
2600
1300
2600
0.9
1.2
1.2
0.7
1.0
1.2
0.9
1.2
1.2
0.7
0.9
1.2
0.7
0.9
1.2
0.9
1.2
0.3
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.3
0.4
0.5
0.2
0.3
0.5
0.1
0.2
0.1
0.1
0.2
0.3
0.1
0.2
0.3
0.1
0.2
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.1
0.2
0.4
0.4
0.2
0.3
0.4
0.3
0.6
0.6
0.2
0.5
0.8
0.2
0.5
0.8
0.4
0.8
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
2.6
3.4
3.9
2.3
3.0
3.8
2.7
3.6
3.5
2.3
2.9
4.0
2.3
2.9
4.0
2.8
4.0
Rev. C | Page 42 of 72
Data Sheet
AD9625
180
PHYSICAL LAYER OUTPUT
160
400
140
300
120
HITS
100
0
100
80
60
–100
40
–200
20
–300
0
–15
–400
–10
–5
0
5
10
15
–150
–100
–50
0
50
100
150
TIME (ps)
11814-026
TIME (ps)
Figure 91. Recovered Data Eye of JESD204B Lane at 6.25 Gbps
Figure 93. Time Interval Histogram Error of JESD204B Output at 6.25 Gbps
SCRAMBLER
The scrambler polynomial is 1 + x14 + x15. The scrambler enable
bit is located in Register 0x06E[7].
1
1–2


1–4
Setting Bit 7 to 0 disables the scrambler.
Setting Bit 7 to 1 enables the scrambler.
TAIL BITS
1–6
The tail bit, PN generator, is located in Register 0x05F[6].
1–8
1–10


1–12
DDC MODES (SINGLE AND DUAL)
1–14
–0.5
–0.4
–0.3
–0.2
–0.1
0
0.1
0.2
0.3
0.4
UI
Figure 92. Bathtub Plot of JESD204B Output at 6.25 Gbps
0.5
11814-027
BER
11814-028
VOLTAGE (mV)
200
Setting Bit 6 to 0 disables the tail bit generator.
Setting Bit 6 to 1 enables the tail bit generator.
The AD9625 contains two separate DDCs that can digitally
downconvert real ADC output data into I/Q decimated data
at a reduced bandwidth. This feature is useful when the full
bandwidth supplied by the 2.6 GSPS converter is not needed.
Figure 94 shows a simplified block diagram of the DDC blocks
as they traverse through the AD9625. Because all JESD204B
frames contain four samples (S = 4), the output from the DDCs
must also output four samples. Table 19 shows the remapping of
I/Q samples to converter samples for the JESD204B interface,
specific to the AD9625.
When in mixed bandwidth mode, DDC 0 is always in high
bandwidth mode and DDC 1 is always in low bandwidth mode.
To match the data throughput of the high bandwidth mode, the
low bandwidth samples are repeated twice in mixed bandwidth
mode. Table 20 lists the four frames of data for both DDC 0
(high bandwidth mode) and DDC 1 (low bandwidth mode).
Rev. C | Page 43 of 72
AD9625
Data Sheet
ADC
16
LOGICAL LANE 1 (L1)
Q0 16
48
I1
DCC 1
LOGICAL LANE 0 (L0)
SAMPLE [N]
16
SAMPLE [N + 1]
REMAP
I/Q TO
CONVERTER
SAMPLES
SAMPLE [N + 2]
JESD204X
LOGICAL LANE 2 (L2)
INTERFACE
(M = 1; L = 8; S = 4;
F = 1; N = 16; N' = 16; LOGICAL LANE 3 (L3)
CF = 0; SCR = 0, 1;
HD = 1;
LOGICAL LANE 4 (L4)
K = SEE SPECS)
LOGICAL LANE 5 (L5)
Q1 16
LOGICAL LANE 6 (L6)
SAMPLE [N + 3]
LOGICAL LANE 7 (L7)
11814-029
12-BIT ADC
SAMPLES [N]
THROUGH [N + 3]
DCC 0
I0
Figure 94. DDC Mapping
Table 19. DDC Remap I/Q to Converter Samples
Application Mode
Single DDC
Dual DDCs
Sample[N]
I0[N]
I0[N]
Sample[N + 1]
Q0[N]
Q0[N]
Sample[N + 2]
I0[N + 1]
I1[N]
Sample[N + 3]
Q0[N + 1]
Q1[N]
Table 20. DDC Mixed Bandwidth Mode
JESD204B Frame Number
Frame 0
Frame 1
Frame 2
Frame 3
Sample[N]
I0[N]
I0[N + 1]
I0[N + 2]
I0[N + 3]
Sample[N + 1]
Q0[N]
Q0[N + 1]
Q0[N + 2]
Q0[N + 3]
Sample[N + 2]
I1[N]
I1[N]
I1[N + 1]
I1[N + 1]
Sample[N + 3]
Q1[N]
Q1[N]
Q1[N + 1]
Q1[N + 1]
CHECKSUM
INITIAL LANE ALIGNMENT SEQUENCE (ILAS)
The JESD204B checksum value is sent with the configuration
parameters during the initial lane alignment sequence. Disabling
the checksum is primarily for debug purposes only.
The AD9625 must support three different ILAS modes that are
controlled using Bits[3:2] in Register 0x05F as follows:
8-BIT/10-BIT ENCODER CONTROL
The 8-bit/10-bit encoder must be controlled in the following
manner:



The bypass 8-bit/10-bit encoder is controlled by
Register 0x60, Bit 2 (0 = 8-bit/10-bit enabled; 1 =
8-bit/10-bit bypassed).
The invert 10-bit encoder is controlled by Register 0x060,
Bit 1 (0 = normal; 1 = invert).
The mirror 10-bit encoder is controlled by Register 0x060,
Bit 0 (0 = normal; 1 = mirrored).
The inversion of the 10-bit values allows the user to swap the
true/complement differential pins swapped on the boards. For
details about Register 0x060, see the Memory Map Register
section.




00: disabled
01: enabled
10: reserved
11: always on test mode
When enabled, the device must also support the capability to
repeat the ILAS using Bits[7:0] in Register 0x062 to determine
the number of times ILAS is repeated (0 = repeat 0 times, ILAS
runs one time only, 1 = repeat one time, ILAS runs twice, and
so forth). Because the number of frames per multiframe is
determined by the value of K, the total number of frames
transmitted during the initial lane alignment sequence is
4 × (K + 1) × (ILAS_COUNT + 1)
where the value of K is defined in Register 0x070, Bits[4:0].
Note that only values divisible by four can be used.
For details about Register 0x05F and Register 0x062, see the
Memory Map Register section.
Rev. C | Page 44 of 72
Data Sheet
AD9625
LANE SYNCHRONIZATION
ADC Output Control Bits on JESD204B Samples
Lane synchronization is defined by Register 0x05F, Bit 4 (0 =
disabled, 1 = enabled). For more information, see the Memory
Map Register section.
When N' = 16 and the ADC resolution is 12, there are four
spare bits available per sample. Two of these spare bits can be
used as control bits, depending on the configuration options.
The control bits are set in Register 0x072, Bits[7:6]. (CS means
control bits per sample.)
Multichip Synchronization Using SYSREF± Timestamp
The SYSREF± pin in the AD9625 can also be used as a
timestamp of data as it passes through the ADC and out the
JESD204B interface. This can be accomplished in two ways:

Replace the least significant converter bit with the
synchronous low to high captured SYSREF± signal. If
the AD9625 were configured as a 12-bit converter, this
would effectively reduce it to a 11-bit converter. This is
accomplished by setting Register 0x03A[7] = 1 in the
register map.
Use the extra output JESD204B control bits to insert the
synchronous low to high captured SYSREF± signal. These
extra control bits are only available while in the JESD204B
generic two, four, and eight lane modes. The generic six lane
mode does not support control bits as both N and N’ = 12.
Six Lane Output Mode
The full data output bandwidth of the eight lane mode can
alternately by output using a six lane mode. This is achieved by
using an N’ = 12 in the six lane mode vs. N’ = 16 in the eight
lane mode for N = 12 ADC data.
The benefit of using the six lane mode is that only six lanes of
output data are needed instead of eight lanes and two output
data lanes can be powered down. A drawback of the six lane
mode is that because there is full efficiency of the link for N =
N’ = 12, there is no spare bandwidth available for control bits.
Therefore, control bit timestamping using SYSREF± cannot be
used in the six lane mode. The LSB of the 12-bit ADC data can
be substituted to output the SYSREF± timestamp.
N+2
N
AIN
N–1
N+3
AD9625
N+1
PIPELINE
LATENCY
ENCODE
CLK
SYSREF
SYSREF
CONTROL BIT
N–1
N
N+1
N+2
N+3
12-BIT ADC
SAMPLES
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
4-BIT CONTROL
AND TAIL BITS

SYSREF± Setup and Hold IRQ
The differential SYSREF± inputs to AD9625 are critical for
JESD204B deterministic latency and sample timestamping. At
a 2.5 GSPS sample rate, the clock period is only 400 ps in
duration from which to accurately latch a SYSREF± edge to
meet setup and hold time to the sample clock. Therefore, it is
important to know the location of the SYSREF± edge relative to
the sampling edge of the encode clock. To help identify the
SYSREF± edge location within the clock period, the AD9625
provides a setup and hold time edge detector circuit to provide
feedback to the system for SYSREF± timing skew and other
alignment procedures. This is a fine timing detector (<1 clock
cycle) and does not provide useful information if coarse timing
(>1 clock cycle) skew adjustment is needed on SYSREF±.
The AD9625 provides an interrupt request (IRQ) bit that
identifies either a setup or a hold time error for the SYSREF±
edge relative to the sampling clock. The error indicates that the
SYSREF± edge is present within the designated time window.
There is a default detector window for both the actual setup and
hold time, with each being nominally 35 ps in time. This error
flag can be identified internal to the AD9625 IRQ register or the
status can be sent externally via the IRQ pin, provided that the
appropriate interrupts are masked or enabled as desired.
A SYSREF± edge located in either the setup or hold violation
window causes ambiguity as to whether the event latchs on
CLK±[N] or CLK±[N + 1]. As a best practice, the SYSREF± edge
must be earlier than both the setup and hold violation windows so
that a deterministic clock can be used to latch SYSREF±.
0
0
0
0
0
11814-480
SAMPLES
00: no control bits sent per sample (CS = 0).
01: one control bit sent per sample, overrange bit enabled,
(CS = 1).
10: two control bits sent per sample, overrange and time
stamped SYSREF± control bit (marks the sample of a rising
edge seen on the SYSREF± pin), (CS = 2). Use of the
SYSREF± control bit (CS = 2) time stamps a particular
analog sample that is seen coincident with a rising signal
on the SYSREF± pins. See the Register 0x08A description to
disable the LMFC JESD204B alignment for timestamping.
Figure 95. A SYSREF± Control Bit Can Be Used to Mark the Same Analog
Sample that is Coincident with a Sampled SYSREF± Edge by CLK±
CLK–
CLK+
SYSREF–
SYSREF+
SETUP IRQ ERROR
11814-481



Figure 96. SYSREF± Edge Falls Within the Actual Setup Time Window and
Triggers an IRQ Error
Rev. C | Page 45 of 72
AD9625
Data Sheet
an IRQ event equal to 1. All other settings would be 0. Because
there is no edge in the hold guardband delays, those would all
be 0 if they were set.
CLK–
CLK+
SYSREF–
After each IRQ alert, the status needs to be cleared, as it does
not automatically clear itself, even if the alert conditions are no
longer valid. For either the SYSREF± setup or hold IRQ alert,
the status is cleared using Register 0x03A[6]. Setting Register
0x03A[6] = 1 clears and hold the IRQ in a reset value of 0. To
allow IRQ flags pertaining to SYSREF± again, set Register
0x03A[6] = 0.
SETUP GUARDBAND
IRQ DELAYS
HOLD GUARDBAND
IRQ DELAYS
CLK+
SYSREF–
11814-483
111
110
101
100
011
010
001
000
000
010
001
011
100
101
110
111
SYSREF+
HOLD AND
GUARDBAND TIME
SYSREF–
111
110
101
100
011
010
HOLD AND
GUARDBAND TIME
11814-484
SETUP AND
GUARDBAND TIME
001
000
000
SYSREF+
Figure 99. SYSREF± Edge Falls Within the Guardbanded Hold Time Window
and Triggers an IRQ Error
In Figure 99, the SYSREF± edge misses the default setup and
hold time of the clock, but would trigger an IRQ event only if
certain hold time guardband delays were used. For this figure,
all of the hold guardband delays that would place the SYSREF±
crossing edge between it and the dotted black line would incur
an IRQ event equal to 1. All other settings would be 0. Because
there is no edge in the setup guardband delays, those would all
be 0 if they were set.
Table 22. IRQ Outcomes for All Setup or Hold Guardband
Settings Using the Case in Figure 99
CLK–
SETUP AND
GUARDBAND TIME
CLK+
010
001
The IRQ flag for the SYSREF± setup window is in Register
0x100[2], while the IRQ flag for the SYSREF± hold window is
in Register 0x100[3]. The IRQ flag mask for the SYSREF± setup
window is in Register 0x101[2], while the IRQ flag mask for the
SYSREF± hold window is in Register 0x101[3].
HOLD GUARDBAND
IRQ DELAYS
CLK–
011
There are 3 bits that define the SYSREF± setup time guardband
located in Register 0x13C[7:5]. There are 3 bits that define the
SYSREF± hold time guardband located in Register 0x13B[7:5].
A setting of 000b for either is the default of no additional timing
guardband, with just the actual setup and hold time window
used as the IRQ.
Hold
0
0
0
0
0
0
0
0
SETUP GUARDBAND
IRQ DELAYS
100
Additional guardband delays can be added to each of the default
setup and hold time windows. This yields more information to
the system about the placement of the SYSREF± edge within the
clock period and help identify the proximity of the SYSREF± edge
to the actual setup and hold time windows. With a default
setting of 00b for both setup and hold, each has seven
additional settings to increase the guardband timing feedback
information.
Setup
0
0
0
0
1
1
1
1
101
IRQ Guardband Delays (SYSREF± Setup and Hold)
Setting/IRQ
000
001
010
011
100
101
110
111
110
HOLD IRQ ERROR
Figure 97. SYSREF± Edge Falls Within the Actual Hold Time Window and
Triggers an IRQ Error
Table 21. IRQ Outcomes for All Setup or Hold Guardband
Settings for the Case in Figure 98
111
11814-482
SYSREF+
Figure 98. SYSREF± Edge Falls Within the Guardbanded Setup Time Window
and Triggers an IRQ Error
Setting/IRQ
000
001
010
011
100
101
110
111
In Figure 98, the SYSREF± edge meets the default setup and
hold time of the clock, but would trigger an IRQ event only if
certain setup time guardband delays were used. For this figure,
all of the setup guardband delays that would place the SYSREF±
crossing edge between it and the dotted black line would incur
Rev. C | Page 46 of 72
Setup
0
0
0
0
0
0
0
0
Hold
0
0
0
0
1
1
1
1
Data Sheet
AD9625
HOLD GUARDBAND
[N] IRQ DELAYS
CLK±[N + 1]
SYSREF–
SETUP AND
GUARDBAND TIME [N + 1]
11814-485
000
001
010
011
111
110
101
100
011
010
001
000
000
001
010
011
100
101
110
111
010
001
000
SYSREF+
HOLD AND
GUARDBAND TIME [N]
Figure 100. SYSREF± Edge Falls Within Both the Latest Hold Time
Guardbanded of CLK±[N] and the Earliest Setup Time Guardband of
CLK±[N + 1] and Triggers an IRQ Error
Table 23. IRQ Outcomes for All Setup or Hold Guardband
Settings Using the Case in Figure 100
Setting/IRQ
000
001
010
011
100
101
110
111
Setup
0
0
0
0
0
0
0
1
CLK–
CLK+
SYSREF–
110
101
100
011
010
001
111
11814-486
SETUP AND
GUARDBAND TIME
000
000
010
001
011
100
101
110
SYSREF+
HOLD AND
GUARDBAND TIME
Figure 101. SYSREF± Edge Changes Phase Relative to the Encode Clock,
Which can be Detected When the Edge Crosses Through the Guardband
Setup Time
Setting/IRQ
000
001
010
011
100
101
110
111
OVERLAP
CLK±[N]
HOLD GUARDBAND
IRQ DELAYS
Table 24. IRQ Outcomes for all Setup or Hold Guardband
Settings Using the Case in Figure 101
SETUP GUARDBAND
[N +1] IRQ DELAYS
CLK–
CLK+
SETUP GUARDBAND
IRQ DELAYS
111
In the case where the encode clock used for the AD9625 is
sufficiently fast (>1.75 GSPS), the guardband delays for the
earliest setup and latest hold condition starts to overlap in time
due to the fast clock period. This case occurs when the encode
clock period is smaller than 16× the nominal delay guardband
window of 35 ps or (1/fS < 16 × 35 ps). The earliest setup guardband delays from clock N can overlap with the latest guardband
delays from CLK±[N + 1]. When this is the case, a SYSREF±
edge located in one of these overlapped guardband delays
triggers an IRQ event for both the setup and hold detection.
While it is possible to make use of this information, it is
suggested to limit the number of valid settings to no more
than 5 (100b) and below when sampling above 1.75 GSPS to
avoid this situation.
Hold
0
0
0
0
0
0
0
1
Setup
0
0
0
0
1
1
1
1
Hold
0
0
0
0
0
0
0
0
Setting/IRQ
000
001
010
011
100
101
110
111
Setup
0
0
1
1
1
1
1
1
Hold
0
0
0
0
0
0
0
0
Using Rising/Falling Edges of the CLK to Latch SYSREF±
The SYSREF± signal can be latched on either the rising or
falling edge of the encode clock, based on the value of register
0x03A[3] = 0 (latch on rising edge) or 0x03A[3] = 1 (latch on
falling edge). This does not impact the analog input, which is
always sampled on the rising edge of the encode clock. For
sampling SYSREF±, the falling edge encode capture of CLK±[N]
precedes the rising edge encode capture of CLK±[N], both
corresponding to the same analog sample.
As a secondary use, the SYSREF± edge detector can also alert
the system about phase shift drift between SYSREF± and CLK
due to temperature or supply changes. For example, a conservative
guardband setting could be used, such that an IRQ status of 0
would be seen in ideal conditions. If timing drifts were significant
enough to trigger the IRQ, the system would take action to
adjust the skew of the SYSREF± to CLK accordingly to reestablish
an IRQ of 0.
Rev. C | Page 47 of 72
AD9625
Data Sheet
For synchronous sampling of multiple converters using
SYSREF±, it may be possible to have a scenario shown in
Figure 102. This case uses a SYSREF± capture with the falling
edge of the encode clock first to test the SYSREF± position
using the edge detection window. The three ADC’s each receive
a SYSREF± input that may be skewed in time due to board trace
length or source variance. For ADC[0] SYSREF± meets setup/
hold to CLK±[N], ADC[1] misses setup/hold to CLK±[N], and
ADC[2] is indeterminate as it falls within the setup/hold window
and may be latched by either CLK±[N] or CLK±[N + 1].
CLK+
CLK±[N]
FALLING
CLK±[N]
RISING
Bits[3:0] in Register 0x061 determine the type of test patterns
that are injected, as follows:






CLK±[N + 1]
FALLING
CLK–
SYSREF–
SYSREF+
ADC[0]

SYSREF–
SYSREF–
SYSREF+
ADC[1]
ADC[2]
11814-487
SYSREF+
?
Figure 102. SYSREF± Case From Three ADCs Having Various Phase Delays
Relative to the Falling Edge of the Encode Clock and is Latched on Different
Sample Clock Edges CLK±[N] or CLK±[N + 1]
As a solution to this case, the SYSREF± capture edge can be
changed from falling to rising, which is still captured to the
analog sample from CLK±[N]. When this is done, all three
ADC’s now meet the setup/hold time for the rising edge capture
of CLK±[N].
CLK–
CLK±[N]
RISING
CLK±[N + 1]
FALLING


SYSREF+
ADC[1]
11814-488
SYSREF–

ADC[0]
SYSREF–
SYSREF+
The AD9625 supports the following application layer modes via
Register 0x063[3:0]:

SYSREF–
SYSREF+
JESD204B APPLICATION LAYERS

CLK+
CLK±[N]
FALLING





ADC[2]
Figure 103. Changing the Latching Edge to Rising for All Three ADCs,
SYSREF± Can Now be Aligned to CLK±[N]


Test Modes
Bits[5:4] in Register 0x061 control the JESD204B interface test
injection points.




0000: normal operation (test mode disabled).
0001: alternating checkerboard.
0010: 1/0 word toggle.
0011: PN sequence: long (x23 + x18 + 1).
0101: continuous/repeat user test mode; most significant
bits from 16-bit user pattern (1, 2, 3, 4) are placed on the
output for one clock cycle and then repeated. (Output user
pattern: 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, ….)
0110: single user test mode; most significant bits from the
16-bit user pattern (1, 2, 3, 4) placed on the output for one
clock cycle and then outputs all zeros. (Output user
pattern: 1, 2, 3, 4, then output all zeros.)
0111: Ramp output (dependent on test injection point and
number of bits, N).
1000: modified RPAT test sequence.
1001: unused.
1010: JSPAT test sequence.
1011: JTSPAT test sequence.
1100 to 1111: unused.
00: 16-bit test generation data injected at the sample input
to the link.
01: 10-bit test generation data injected at the output of the
8-bit/10-bit encoder (at the input to PHY).
10: 8-bit test generation data injected at the input of the
scrambler.
11: reserved.
Rev. C | Page 48 of 72
0100: fS × x mode which supports line rates at integer
multiples of the sample rates
1000: single DDC mode, high bandwidth mode (only
DDC 0 used)
1001: single DDC mode, low bandwidth mode (only
DDC 0 used)
1010 to 1011: unused
1100: dual DDC mode, high bandwidth mode (both
DDC 0 and DDC 1 used)
1101: dual DDC mode, low bandwidth mode (both DDC 0
and DDC 1 used)
1110: dual DDC mode, mixed bandwidth mode (DDC 0
high bandwidth mode, DDC 1 low bandwidth mode,
samples repeated)
Data Sheet
AD9625
fS × 2, fS × 4, fS × 8 Modes
To allow the line rate of the JESD204B interface to map directly
into an integer of the converter sample rate, a four to five rate
conversion takes place to group the 12-bit ADC samples into
blocks of five samples. During this rate conversion, for every
five 12-bit ADC sample, an extra user defined, 4-bit nibble is
appended to create a 64-bit frame. Next, the 64-bit low multiplier frame maps into the four 16-bit JESD204B samples. The
most significant 16-bits of the 64-bit low multiplier frame map
to the oldest 16-bit JESD204B sample and the least significant
16-bits of the 64-bit low multiplier frame map to the most
recent 16-bit JESD204B sample.
The JESD204B low multiplier mode application layer adds a
rate conversion on top of a JESD204B transmitter/receiver with
the following configuration parameters: M = 1; L = 8; S = 4;
F = 1; N = 16; N' = 16; CS = 0; CF = 0; SCR = 0, 1; HD = 1;
K = reference JESD204B specification.
In this mode, there are five actual samples per frame and
scrambling can be optionally enabled in the JESD204B
interface. The transmit portion of the low multiplier mode
JESD204B application layer is shown in Figure 104.
The first step in this application layer is where 12-bit ADC
samples are divided into six bytes.
The receive portion of the fS × 2 JESD204B application layer is
shown in Figure 105.
fS × 2 APPLICATION LAYER (TRANSMIT)
ADC SAMPLE N + 2
(12 BITS)
CONTROL BITS FOR SAMPLE N + 3
(CS = 0, 2 OR 4 BITS)
ADC CONVERTER SAMPLE N + 3
(N = 8, 10 OR 12 BITS)
CONTROL BITS FOR SAMPLE N + 2
(CS = 0, 2 OR 4 BITS)
ADC CONVERTER SAMPLE N + 2
(N = 8, 10 OR 12 BITS)
CONTROL BITS FOR SAMPLE N + 1
(CS = 0, 2 OR 4 BITS)
ADC SAMPLE N + 1
(12 BITS)
ADC SAMPLE N + 3
(12 BITS)
4/5 RATE EXCHANGE
S[N][11:0], S[N + 1][11:8]
(16 BITS)
JESD SAMPLE N + 1
(16 BITS)
S[N][15:0]
ADC SAMPLE N + 3
(12 BITS)
ADC SAMPLE N + 4 (4 BITS)
(12 BITS)
S[N + 1][7:0], S[N + 2][11:4] S[N + 2][3:0], S[N + 3][11:0]
(16 BITS)
(16 BITS)
JESD SAMPLE N + 2
(16 BITS)
S[N + 1][15:0]
JESD SAMPLE N
(16 BITS)
JESD SAMPLE N + 3
(16 BITS)
Figure 104. fS × 2 Mode Application Layer (Transmit)
Rev. C | Page 49 of 72
LANE 7
LANE6
LANE 5
LANE 3
LANE 2
LANE 1
APPLICATION
LAYER
S[N + 4][11:0], UD[3:0]
(16 BITS)
JESD204B FRAMER + PHY
(M = 1; L = 8; S = 4; F = 1; N = 16; N' = 16; CF = 0; SCR = 0, 1; HD = 1; K = SEE SPEC
LANE 0
64 BITS
@ fS/5
ADC SAMPLE N + 2
(12 BITS)
S[N + 3][15:0]
ADC SAMPLE N + 1
(12 BITS)
S[N + 2][15:0]
ADC SAMPLE N
(12 BITS)
LANE 4
64 BITS
@ fS/5
USER DEFINED
(FSYNC[3:0])
DATA LINK,
TRANSPORT,
AND PHY LAYERS
11814-032
ADC SAMPLE N
(12 BITS)
48 BITS
@ fS/4
ADC CONVERTER SAMPLE N + 1
(N = 8, 10 OR 12 BITS)
ADC CONVERTER SAMPLE N
(N = 8, 10, OR 12 BITS)
CONTROL BITS FOR SAMPLE N
(CS = 0, 2 OR 4 BITS)
ADC
AD9625
Data Sheet
LANE 7
LANE6
LANE 5
LANE 4
LANE 3
LANE 2
LANE 0
LANE 1
fS × 2 APPLICATION LAYER (RECEIVE)
DATA LINK,
TRANSPORT,
AND PHY LAYERS
64 BITS
@ fS/5
JESD SAMPLE N
(16 BITS)
JESD SAMPLE N + 1
(16 BITS)
S[N][11:0], S[N + 1][11:8]
(16 BITS)
64 BITS
@ fS/5
ADC SAMPLE N
(12 BITS)
S[N + 3][15:0]
S[N + 2][15:0]
S[N][15:0]
S[N + 1][15:0]
JESD204B FRAMER + PHY
(M = 1; L = 8; S = 4; F = 1; N = 16; N' = 16; CF = 0; SCR = 0, 1; HD = 1; K = SEE SPEC
JESD SAMPLE N + 2
(16 BITS)
JESD SAMPLE N + 3
(16 BITS)
S[N + 1][7:0], S[N + 2][11:4] S[N + 2][3:0], S[N + 3][11:0]
(16 BITS)
(16 BITS)
ADC SAMPLE N + 1
(12 BITS)
ADC SAMPLE N + 2
(12 BITS)
ADC SAMPLE N + 3
(12 BITS)
S[N + 4][11:0], UD[3:0]
(16 BITS)
ADC SAMPLE N + 4 (4 BITS)
(12 BITS)
APPLICATION
LAYER
4/5 RATE EXCHANGE
CUSTOMER APPLICATION
Figure 105. fS × 2 Application Layer (Receive)
Rev. C | Page 50 of 72
11814-033
CONTROL BITS FOR SAMPLE N + 3
(CS = 0, 2 OR 4 BITS)
ADC SAMPLE N + 3
(12 BITS)
ADC CONVERTER SAMPLE N + 3
(N = 8, 10 OR 12 BITS)
CONTROL BITS FOR SAMPLE N + 2
(CS = 0, 2 OR 4 BITS)
ADC SAMPLE N + 2
(12 BITS)
ADC CONVERTER SAMPLE N + 2
(N = 8, 10 OR 12 BITS)
CONTROL BITS FOR SAMPLE N + 1
(CS = 0, 2 OR 4 BITS)
ADC SAMPLE N + 1
(12 BITS)
ADC CONVERTER SAMPLE N + 1
(N = 8, 10 OR 12 BITS)
CONTROL BITS FOR SAMPLE N
(CS = 0, 2 OR 4 BITS)
ADC SAMPLE N
(12 BITS)
ADC CONVERTER SAMPLE N
(N = 8, 10, OR 12 BITS)
48 BITS
@ fS/4
USER
DEFINED
Data Sheet
AD9625
Frame alignment character insertion (FACI) is defined in the
register map (see the Memory Map Register section). Disable
FACI only when it is used as a test feature.
The FACI disable bit is located in Register 0x05F, Bit 1. Use the
following settings:


Setting Bit 1 to 0 = FACI enabled
Setting Bit 1 to 1 = FACI disabled
For applications requiring an optimal high power efficiency
and low noise performance, it is recommended that ADP2386
switching regulator is used to convert the 12 V input rail into
two intermediate rails (2.1 V and 3.6 V). These intermediate
rails are then postregulated by very low noise, low dropout (LDO)
regulators (ADP1740, ADP7104, and ADP125). Figure 106
shows the recommended method.
12V
INPUT
THERMAL CONSIDERATIONS
ADP2386
2.1V
BUCK
REGULATOR
ADP1740
1.3V: AVDD1
ADP1740
1.3V: DRVDD1
LDO
LDO
Because of the high power nature of the device, it is critical to
provide airflow and/or install a heat sink when operating at a
high temperature. This ensures that the maximum case
temperature does not exceed 85°C.
ADP2386
BUCK
REGULATOR
3.6V
1.3V: DVDD1
ADP1740
2.5V: AVDD2
ADP1740
2.5V: DRVDD2
LDO
LDO
2.5V: DVDD2
POWER SUPPLY CONSIDERATIONS
ADP125
2.5V: DVDDIO
The AD9625 must be powered by the following two supplies:
AVDD1 = DVDD1 = DRVDD1 = 1.3 V, AVDD2 = DVDD2 =
DRVDD2 = 2.5 V. An optional DVDDIO and SPI_DVDDIO
may be required at 2.5 V.
ADP125
2.5V: SPI_DVDDIO
LDO
Rev. C | Page 51 of 72
LDO
Figure 106. Power Supply Recommendation
11814-054
FRAME ALIGNMENT CHARACTER INSERTION
AD9625
Data Sheet
SERIAL PORT INTERFACE (SPI)
The AD9625 SPI allows the user to configure the converter for
specific functions or operations through a structured register
space provided inside the ADC. The SPI gives the user added
flexibility and customization, depending on the application.
Addresses are accessed via the serial port and can be written to
or read from via the port. Memory is organized into bytes that
can be further divided into fields. These fields are documented
in the Memory Map section.
CONFIGURATION USING THE SPI
Three pins define the SPI of this ADC: the SCLK pin, the SDIO
pin, and the CSB pin (see Table 25). The SCLK (serial clock) pin is
used to synchronize the read and write data presented from/to the
ADC. The SDIO (serial data input/output) pin is a dual-purpose
pin that allows data to be sent and read from the internal ADC
memory map registers. The CSB (chip select bar) pin is an active
low control that enables or disables the read and write cycles.
Table 25. Serial Port Interface Pins
Pin
SCLK
SDIO
CSB
Function
Serial Clock. The serial shift clock input, which is used to
synchronize serial interface, reads and writes.
Serial Data Input/Output. A dual-purpose pin that
typically serves as an input or an output, depending on
the instruction being sent and the relative position in the
timing frame.
Chip Select Bar. An active low control that gates the read
and write cycles.
The falling edge of CSB, in conjunction with the rising edge of
SCLK, determines the start of the framing.
Other modes involving the CSB pin are available. The CSB pin
can be held low indefinitely, which permanently enables the
device; this is called streaming. The CSB pin can stall high
between bytes to allow for additional external timing. When
CSB is tied high, SPI functions are placed in a high impedance
mode. This mode turns on any SPI pin secondary functions.
All data is composed of 8-bit words. The first bit of each individual
byte of serial data indicates whether a read or write command is
issued. This allows the SDIO pin to change direction from an
input to an output.
In addition to word length, the instruction phase determines
whether the serial frame is a read or write operation, allowing
the serial port to be used both to program the chip and to read
the contents of the on-chip memory. If the instruction is a read
operation, performing a read causes the SDIO pin to change
direction from an input to an output at the appropriate point in
the serial frame.
Data can be sent in MSB first mode or in LSB first mode. MSB
first is the default on power-up and can be changed via the SPI
port configuration register.
HARDWARE INTERFACE
The pins described in Table 25 comprise the physical interface
between the user programming device and the serial port of the
AD9625. The SCLK pin and the CSB pin function as inputs when
using the SPI interface. The SDIO pin is bidirectional, functioning
as an input during write phases and as an output during read.
The SPI interface is flexible enough to be controlled by either
FPGAs or microcontrollers. One method for SPI configuration
is described in detail in the AN-812 Application Note,
Microcontroller-Based Serial Port Interface (SPI) Boot Circuit.
Do not activate the SPI port during periods when the full dynamic
performance of the converter is required. Because the SCLK signal,
the CSB signal, and the SDIO signal are typically asynchronous
to the ADC clock, noise from these signals can degrade converter
performance. If the on-board SPI bus is used for other devices, it
may be necessary to provide buffers between this bus and the
AD9625 to prevent these signals from transitioning at the converter
inputs during critical sampling periods.
Rev. C | Page 52 of 72
Data Sheet
AD9625
MEMORY MAP
READING THE MEMORY MAP REGISTER
Default Values
Each row in the memory map register contains eight bit
locations. The memory map is roughly divided into three
sections: the chip configuration registers (Address 0x000 to
Address 0x002); the transfer register (Address 0x0FF); and the
ADC functions registers, including setup, control, and test
(Address 0x008 to Address 0x13A).
After the AD9625 is reset, critical registers are loaded with
default values. The default values for the registers are given in
the memory map register tables.
The memory map register tables provide the default hexadecimal
value for each hexadecimal address that is listed.
The column with the heading, Bit 7 (MSB), is the start of the
default hexadecimal value given. For example, Address 0x14,
the output mode register, has a hexadecimal default value of
0x01. This means that Bit 0 = 1, and the remaining bits are 0s.
This setting is the default output format value, which is twos
complement. For more information on this function and others,
see the AN-877 Application Note, Interfacing to High Speed
ADCs via SPI.
Open and Reserved Locations
All address and bit locations are not currently supported for this
device. Unused bits of a valid address location should be written
with 0s. Writing to these locations is required only when a
portion of an address location is open. If the entire address
location is open, this address location should not be written.
Logic Levels
An explanation of logic level terminology follows:


“Bit is set” is synonymous with “bit is set to Logic 1” or
“writing Logic 1 for the bit.”
“Clear a bit” is synonymous with “bit is set to Logic 0” or
“writing Logic 0 for the bit.”
Transfer Register Map
Register addresses for the AD9625 are shadowed. Register
writes do not affect device operation until a transfer command
is issued by writing 0x01 to Address 0x0FF, thereby setting the
transfer bit. This allows the registers to update internally and
simultaneously when the transfer bit is set. The internal update
occurs when the transfer bit is set, and then the bit automatically clears.
MEMORY MAP REGISTERS
Address and bit locations that are not included in Table 26
through Table 116 are not currently supported for this device.
Table 26. SPI Configuration Register, Address 0x000 (Default = 0x18)
Bit No.
7
6
Access
RW
5
RW
4
3
2
R
R
RW
1
RW
0
Unused
Bit Description
Unused.
SPI least significant bit (LSB) first.
1: LSB shifted first for all SPI operations. For multibyte SPI operations, the addressing increments
automatically.
0: most significant bit (MSB) shifted first for all SPI operations. For multibyte SPI operations, the
addressing decrements automatically.
Self clearing soft reset.
1: reset the SPI registers (self clearing).
0: do nothing.
13-bit addressing enabled.
13-bit addressing enabled.
Self clearing soft reset.
1: reset the SPI registers(self clearing).
0: do nothing.
SPI LSB first.
1: LSB shifted first for all SPI operations. For multibyte SPI operations, the addressing increments
automatically.
0: MSB shifted first for all SPI operations. For multibyte SPI operations, the addressing decrements
automatically.
Unused.
Table 27. Chip ID Register, Address 0x001 (Default = 0x41)
Bit No.
[7:0]
Access
R
Bit Description
Chip ID.
Rev. C | Page 53 of 72
AD9625
Data Sheet
Table 28. Chip Grade Register, Address 0x002 (Default = 0x14)
Bit No.
[7:6]
[5:4]
Access
R
[3:0]
Bit Description
Unused.
Chip ID/speed grade.
11: 2.6 GSPS.
10: 2.5 GSPS.
01: 2.0 GSPS.
Unused.
Table 29. Power Control Mode Register, Address 0x008 (Default = 0x80)
Bit No.
7
6
5
[4:2]
[1:0]
Access
RW
Bit Description
Reserved.
Reserved.
Reserved.
Reserved.
Chip power modes.
00: normal mode (power-up).
01: Power-down.
10: standby mode; digital datapath clocks disabled, JESD204B interface enabled, outputs enabled.
11: digital datapath reset mode; digital data path clocks enabled, digital data path held in reset, JESD204B interface held
in reset, outputs enabled.
Table 30. PLL Status Register, Address 0x00A (Default = 0x00)
Bit No.
7
Access
RO
[6:0]
Bit Description
PLL locked status bit.
0: PLL is unlocked.
1: PLL is locked.
Reserved.
Table 31. ADC Test Control Register, Address 0x00D (Default = 0x00)
Bit No.
7
Access
RW
6
5
RW
4
[3:0]
RW
RW
Bit Description
ADC datapath user test mode control. Note that these bits are only used when Register 0x00D, Bits[3:0] is in user input
mode (Register 0x00D[3:0] = 1000); otherwise, they are ignored.
0: continuous/repeat pattern mode. Place each user pattern (1, 2, 3, 4) on the output for one clock cycle and then repeat.
(Output user pattern: 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, …)
1: single pattern mode. Place each user pattern (1, 2, 3, 4) on the output for one clock cycle and then output all zeros.
(Output user pattern: 1, 2, 3, 4, then output all zeros.)
Unused.
ADC long psuedo random number test generator reset.
0: long PN enabled.
1: long PN held in reset.
Unused.
ADC data output test generation mode.
0000: off, normal operation.
0001: midscale short.
0010: positive full scale.
0011: negative full scale.
0100: alternating checkerboard.
0101: PN sequence, long.
0110: unused.
0111: one-/zero-word toggle.
1000: user test mode. Used with Register 0x00D[7] and user pattern (1, 2, 3, 4) registers.
1001 to 1110: unused.
1111: ramp output.
Rev. C | Page 54 of 72
Data Sheet
AD9625
Table 32. Data Path Customer Offset Register, Address 0x010 (Default = 0x00)
Bit No.
[7:6]
[5:0]
Access
RW
Bit Description
Unused.
Digital datapath offset. Twos complement offset adjustment aligned with least converter resolution.
011111: +31.
011110: +30.
…
000001: +1.
000000: 0.
111111: −1.
…
100001: −31.
100000: −32.
Table 33. Output Mode Register, Address 0x014 (Default = 0x01)
Bit No.
[7:5]
4
Access
RW
3
2
RW
[1:0]
RW
Bit Description
Unused.
Chip output disable. Bit 4 enables and disables the digital outputs from the ADC.
0: enable.
1: disable.
Unused.
Digital ADC sample invert.
0: ADC sample data is not inverted.
1: ADC sample data is inverted.
Digital ADC data format select (DFS). Note that the use of the muxed SDIO pin to control Register 0x014[1:0] is not
supported on the AD9625.
00: offset binary.
01: twos complement (default).
10: reserved.
11: reserved.
Table 34. Serializer Output Adjust, Register, Address 0x015 (Default = 0x54)
Bit No.
7
Access
RW
[6:5]
RW
[4:0]
RW
Bit Description
Serializer output polarity selection.
0: normal, not inverted.
1: output driver polarity inverted.
Serializer output emphasis amplitude control.
00: 0 mV de-emphasis differential peak to peak.
01: 160 mV de-emphasis differential peak to peak.
10: 80 mV de-emphasis differential peak to peak.
11: 40 mV de-emphasis differential peak to peak.
Reserved.
Table 35. User Test Pattern 1 LSB Register, Address 0x019 (Default = 0x00)
Bit No.
[7:0]
Access
RW
Bit Description
User Test Pattern 1 least significant byte. Note that these bits are used only when Register 0x00D, Bits[3:0] is in user
input mode (Register 0x00D[3:0] = 1000), or when Register 0x061, Bits[3:0] is in the scrambler or 10-bit test modes
(Register 0x061[3:0] = 0100 to 0111). Otherwise, these bits are ignored.
Table 36. User Test Pattern 1 MSB Register, Address 0x01A (Default = 0x00)
Bit No.
[7:0]
Access
RW
Bit Description
User Test Pattern 1 most significant byte. Note that these bits are used only when Register 0x00D, Bits[3:0] is in user
input mode (Register 0x00D[3:0] = 1000). Otherwise, these bits are ignored.
Rev. C | Page 55 of 72
AD9625
Data Sheet
Table 37. User Test Pattern 2 LSB Register, Address 0x01B (Default = 0x00)
Bit No.
[7:0]
Access
RW
Bit Description
User Test Pattern 2 least significant byte. Note that these bits are used only when Register 0x00D, Bits[3:0] is in user
input mode (Register 0x00D[3:0] = 1000). Otherwise, these bits are ignored.
Table 38. User Test Pattern 2 MSB Register, Address 0x01C (Default = 0x00)
Bit No.
[7:0]
Access
RW
Bit Description
User Test Pattern 2 most significant byte. Note that these bits are used only when Register 0x00D, Bits[3:0] is in user
input mode (Register 0x00D[3:0] = 1000). Otherwise, these bits are ignored.
Table 39. User Test Pattern 3 LSB Register, Address 0x01D (Default = 0x00)
Bit No.
[7:0]
Access
RW
Bit Description
User Test Pattern 3 least significant byte. Note that these bits are used only when Register 0x00D, Bits[3:0] is in user
input mode (Register 0x00D[3:0] = 1000). Otherwise, these bits are ignored.
Table 40. User Test Pattern 3 MSB Register, Address 0x01E (Default = 0x00)
Bit No.
[7:0]
Access
RW
Bit Description
User Test Pattern 3 most significant byte. Note that these bits are used only when Register 0x00D, Bits[3:0] is in user
input mode (Register 0x00D[3:0] = 1000). Otherwise, these bits are ignored.
Table 41. User Test Pattern 4 LSB Register, Address 0x01F (Default = 0x00)
Bit No.
[7:0]
Access
RW
Bit Description
User Test Pattern 4 least significant byte. Note that these bits are used only when Register 0x00D, Bits[3:0] is in user
input mode (Register 0x00D[3:0] = 1000). Otherwise, these bits are ignored.
Table 42. User Test Pattern 4 MSB Register, Address 0x020 (Default = 0x00)
Bit No.
[7:0]
Access
RW
Bit Description
User Test Pattern 4 most significant byte. Note that these bits are used only when Register 0x00D, Bits[3:0] is in user
input mode (Register 0x00D[3:0] = 1000). Otherwise, these bits are ignored.
Table 43. Synthesizer PLL Control Register, Address 0x021 (Default = 0x00)
Bit No.
[7:5]
4
3
[2:0]
Access
RW
RW
Bit Description
Unused.
1: force power-down of VCO LDO.
Reserved for future use.
Unused.
Table 44. ADC Analog Input Control Register, Address 0x02C (Default = 0x00)
Bit No.
[7:3]
2
Access
RW
[1:0]
Bit Description
Unused.
Set function on VMON pin.
0: unused.
1: allows external reference on VMON pin.
Unused.
Table 45. SYSREF± Control Register, Address 0x03A (Default = 0x00)
Bit No.
7
Access
RW
6
RW
5
Bit Description
SYSREF± status bit replaces the LSB from the converter.
0: normal mode.
1: SYSREF± status bit replaces the LSB.
SYSREF± status bit flag reset. To use the flags, Register 0x03A, Bit 1 must be set to high.
0: normal flag operation.
1: SYSREF± status bit flags held in reset.
Unused.
Rev. C | Page 56 of 72
Data Sheet
Bit No.
4
Access
RW
3
RW
2
RW
1
RW
0
AD9625
Bit Description
SYSREF± transition selection.
0: SYSREF± is valid on low to high transitions using selected CLK edge.
1: SYSREF± is valid on high to low transitions using selected CLK edge.
SYSREF± capture edge selection.
0: captured on rising edge of CLK input.
1: captured on falling edge of CLK input.
SYSREF± next mode.
0: continuous mode.
1: next SYSREF± mode: uses the next valid edge only of the SYSREF± pin. Subsequent edges of the SYSREF± pin are
ignored. When the next system reference is found, Bit 1 of Register 0x03A clears.
SYSREF± pins enable.
0: SYSREF± disabled.
1: SYSREF± enabled. When Register 0x03A, Bit 2 = 1, only the next valid edge of the SYSREF± pins is used. Subsequent
edges of the SYSREF± pin are ignored.
Unused.
Table 46. Fast Detect Control Register, Address 0x045 (Default = 0x00)
Bit No.
[7:4]
3
2
1
0
Access
RW
RW
RW
Bit Description
Unused.
Force the fast detect output pin.
0: normal operation of fast detect pin.
1: force a value on the fast detect pin (see Bit 2 in this table, Table 46).
The fast detect output pin is set to the value in this bit (Register 0x045[2]) when the output is forced.
Unused.
Enable fast detect on the corrected ADC data.
0: fine fast detect disabled.
1: fine fast detect enabled.
Table 47. Fast Detect Upper Threshold Register, Address 0x047 (Default = 0x00)
Bit No.
[7:0]
Access
RW
Bit Description
These bits are the LSBs of the fast detect upper threshold. These eight LSBs of the programmable 12-bit upper threshold
are compared to the fine ADC magnitude.
Table 48. Fast Detect Upper Threshold Register, Address 0x048 (Default = 0x00)
Bit No.
[7:4]
[3:0]
Access
RW
Bit Description
Unused.
These bits are the MSBs of the fast detect upper threshold. These four MSBs of the programmable 12-bit upper
threshold are compared to the fine ADC magnitude.
Table 49. Fast Detect Lower Threshold Register, Address 0x049 (Default = 0x00)
Bit No.
[7:0]
Access
RW
Bit Description
These bits are the LSBs of the fast detect lower threshold. These eight LSBs of the programmable 12-bit lower threshold
are compared to the fine ADC magnitude.
Table 50. Fast Detect Lower Threshold Register, Address 0x04A (Default = 0x00)
Bit No.
[7:4]
[3:0]
Access
RW
Bit Description
Unused.
MSBs of the fast detect lower threshold. These four MSBs of the programmable 12-bit lower threshold are compared to
the fine ADC magnitude.
Table 51. Fast Detect Dwell Time Counter Threshold Register, Address 0x04B (Default = 0x00)
Bit No.
[7:0]
Access
RW
Bit Description
These bits are the LSBs of the fast detect dwell time counter target. This is the value for a 16-bit counter that determines
the length of time that the ADC data must remain below the lower threshold before the FD pin reset to 0.
Rev. C | Page 57 of 72
AD9625
Data Sheet
Table 52. Fast Detect Dwell Time Counter Threshold Register, Address 0x04C (Default = 0x00)
Bit No.
[7:0]
Access
RW
Bit Description
These bits are the MSBs of the fast detect dwell time counter target. This is the value for a 16-bit counter that
determines the length of time that the ADC data must remain below the lower threshold before the FD pin resets to 0.
Note that the fast detect (FD) pin deasserts after the ADC codes stay below the lower target for the number of samples
indicated by the value in Register 0x04C[7:0].
Table 53. JESD204B Quick Configuration Register, Address 0x05E (Default = 0x00)
Bit No.
[7:0]
Access
RW
Bit Description
JESD204B serial quick configuration (self clearing). This register is self clearing and does not control anything in the
AD9625 directly; it only changes the value of the other JESD240B registers that control the chip. Because this register is
self clearing, it always returns to 000 after each write. To use the quick configuration feature, write to this register first,
then, if there are any changes that need to be made to any of the following settings, write to the other JESD204B
registers.
0x00: configuration determined by other registers. Because the register is self clearing, it always returns to this value
after each write.
0x01: reserved.
0x02: Generic Two Lane Configuration Register 0x063[3:0] = 0x0; Register 0x06E[4:0] = 0x1; Register 0x072[4:0] = 0xB;
Register 0x073[4:0] = 0xF.
0x04: Generic Four Lane Configuration Register 0x063[3:0] = 0x0; Register 0x06E[4:0] = 0x3; Register 0x072[4:0] = 0xB;
Register 0x073[4:0] = 0xF.
0x06: Generic Six Lane Configuration Register 0x063[3:0] = 0x0; Register 0x06E[4:0] = 0x5; Register 0x072[4:0] = 0xB;
Register 0x073[4:0] = 0xB.
0x08: Generic Eight Lane Configuration Register 0x063[3:0] = 0x0; Register 0x06E[4:0] = 0x7; Register 0x072[4:0] = 0xB;
Register 0x073[4:0] = 0xF.
0x42: reserved.
0x44: reserved.
0x48: fS × 2 mode, eight lanes. Register 0x063[3:0] = 0x4; Register 0x06E[4:0] = 0x7; Register 0x072[4:0] = 0xF;
Register 0x073[4:0] = 0xF.
0x81: 1 DDC (high BW), one lane. Register 0x063[3:0] = 0x8; Register 0x06E[4:0] = 0x0; Register 0x072[4:0] = 0xF;
Register 0x073[4:0] = 0xF.
0x82: 1 DDC (high BW), two lanes. Register 0x063[3:0] = 0x8; Register 0x06E[4:0] = 0x1; Register 0x072[4:0] = 0xF;
Register 0x073[4:0] = 0xF.
0x91: 1 DDC (low BW), one lane. Register 0x063[3:0] = 0x9; Register 0x06E[4:0] = 0x0; Register 0x072[4:0] = 0xF;
Register 0x073[4:0] = 0xF.
0xC1: 2 DDCs (high BW), one lane. Register 0x063[3:0] = 0xC; Register 0x06E[4:0] = 0x0; Register 0x072[4:0] = 0xF;
Register 0x073[4:0] = 0xF.
0xC2: 2 DDCs (high BW), two lanes. Register 0x063[3:0] = 0xC; Register 0x06E[4:0] = 0x1; Register 0x072[4:0] = 0xF;
Register 0x073[4:0] = 0xF.
0xC4: 2 DDCs (high BW), four lanes. Register 0x063[3:0] = 0xC; Register 0x06E[4:0] = 0x3; Register 0x072[4:0] = 0xF;
Register 0x073[4:0] = 0xF.
0xD1: 2 DDCs (low BW), one lane. Register 0x063[3:0] = 0xD; Register 0x06E[4:0] = 0x0; Register 0x072[4:0] = 0xF;
Register 0x073[4:0] = 0xF.
0xD2: 2 DDCs (low BW), two lanes. Register 0x063[3:0] = 0xD; Register 0x06E[4:0] = 0x1; Register 0x072[4:0] = 0xF;
Register 0x073[4:0] = 0xF.
0xE1: 2 DDCs (mixed BW), one lane. Register 0x063[3:0] = 0xE; Register 0x06E[4:0] = 0x0; Register 0x072[4:0] = 0xF;
Register 0x073[4:0] = 0xF.
0xE2: 2 DDCs (mixed BW), two lanes. Register 0x063[3:0] = 0xE; Register 0x06E[4:0] = 0x1; Register 0x072[4:0] = 0xF;
Register 0x073[4:0] = 0xF.
0xE4: 2 DDCs (mixed BW), four lanes. Register 0x063[3:0] = 0xE; Register 0x06E[4:0] = 0x3; Register 0x072[4:0] = 0xF;
Register 0x073[4:0] = 0xF.
All other values have no effect.
Rev. C | Page 58 of 72
Data Sheet
AD9625
Table 54. JESD204B Link Control Register 1, Address 0x05F (Default = 0x14)
Bit No.
7
6
Access
RW
5
RW
4
RW
[3:2]
RW
1
RW
0
RW
Bit Description
Unused.
JESD204B serial tail bit, PN, enable. Note that the following equation can be used to determine the number of PN bits
sent per sample = N' − N – CS (the number of control bits per sample).
0: serial tail bit, PN, disabled. Unused extra tail bits are padded with zeros.
1: serial tail bit, PN, enabled. Unused extra tail bits are padded with a pseudo random number sequence from a 31-bit
LFSR (see JESD204B 5.1.4).
JESD204B serial test sample enable.
0: JESD204B test samples disabled.
1: JESD204B test samples enabled. The transport layer test sample sequence (as specified in JESD204B Section 5.1.6.2) is
sent on all link lanes.
JESD204B serial lane synchronization enable. Note that the frame character insertion must be enabled (Register 0x05F[1] = 0)
to enable lane synchronization.
0: lane synchronization disabled. Both sides do not perform lane synchronization; frame alignment character insertion
always uses /K28.7/ control characters (see JESD204B 5.3.3.4).
1: lane synchronization enabled. Both sides perform lane sync; frame alignment character insertion uses either /K28.3/
or /K28.7/ control characters (see JESD204B 5.3.3.4).
JESD204B serial initial lane alignment sequence mode.
00: initial lane alignment sequence disabled (JESD204B 5.3.3.5).
01: initial lane alignment sequence enabled (JESD204B 5.3.3.5).
10: reserved.
11: initial lane alignment sequence always on test mode; the JESD204B data link layer test mode (where repeated lane
alignment sequence, as specified in JESD204B section 5.3.3.9.2) is sent on all lanes.
JESD204B serial frame alignment character insertion (FACI) disable.
0: frame alignment character insertion enabled (JESD204B 5.3.3.4).
1: frame alignment character insertion disabled. Note that this is for debug only (JESD204B 5.3.3.4).
JESD204B serial transmit link power-down (active high). Note that the JESD204B transmitter link must be powered
down while changing any of the link configuration bits.
0: JESD204B serial transmit link enabled. Transmission of the /K28.5/ characters for code group synchronization is
controlled by the SYNCINB± pins.
1: JESD204B serial transmit link powered down (held in reset and clock gated).
Table 55. JESD204B Link Control Register 2, Address 0x060 (Default = 0x00)
Bit No.
[7:6]
Access
RW
5
RW
[4:3]
2
RW
1
RW
0
RW
Bit Description
JESD204B serial synchronization mode.
00: normal mode.
01: reserved.
10: SYNCINB± active mode. SYNCINB± pins are active: force code group synchronization.
11: SYNCINB± pins disabled.
JESD204B serial synchronization pin invert.
0: SYNCINB± pins not inverted.
1: SYNCINB± pins inverted.
Unused.
JESD204B Serial 8-bit/10-bit bypass (test mode only).
0: 8-bit/10-bit enabled.
1: 8-bit/10-bit bypassed (most significant two bits are 0).
JESD204B 10-bit serial transmit bit invert. Note that in the event that the CML signals are reversed in a system board
layout, this bit effectively inverts the differential outputs from the PHY.
0: normal.
1: invert the a, b, c, d, e, f, g, h, i, j bits.
JESD204B 10-bit serial transmit bit mirror.
0: 10-bit serial bits are not mirrored. Transmit bit order is alphabetical: a, b, c, d, e, f, g, h, i, j.
1: 10-bit serial bits are mirrored. Transmit bit order is alphabetically reversed: j, i, h, g, f, e, d, c, b, a.
Rev. C | Page 59 of 72
AD9625
Data Sheet
Table 56. JESD204B Link Control Register 3, Address 0x061 (Default = 0x00)
Bit No.
7
Access
RW
6
RW
[5:4]
RW
[3:0]
RW
Bit Description
JESD204B checksum disable.
0: checksum enabled in the link configuration parameter. Normal operation.
1: checksum disabled in the link configuration parameter (set to zero). For testing purposes only.
JESD204B checksum mode.
0: checksum is the sum of all 8-bit registers in the link configuration fields.
1: checksum is the sum of all individual link configuration fields (LSB aligned).
JESD204B serial test generation input selection.
00: 16-bit test generation data injected at the sample input to the link.
01: 10-bit test generation data injected at the output of the 8-bit/10-bit encoder (at the input to PHY).
10: 8-bit test generation data injected at the input of the scrambler.
11: reserved.
JESD204B serial test generation mode.
0000: normal operation (test mode disabled).
0001: alternating checkerboard.
0010: 1/0 word toggle.
0011: PN sequence (long).
0100: unused.
0101: continuous/repeat user test mode. The most significant bits from the user pattern (1, 2, 3, 4) are placed on the
output for one clock cycle and then repeated (the output user pattern is 1, 2, 3, 4, 1, 2, 3, 4, 1, 2, 3, 4, …).
0110: single user test mode. The most significant bits from the user pattern (1, 2, 3, 4) are placed on the output for one
clock cycle and then output all zeros (the output user pattern is 1, 2, 3, 4, and then outputs all zeros).
0111: ramp output.
1000: modified RPAT test sequence (10-bit value).
1001: unused.
1010: JSPAT test sequence (10-bit value).
1011: JTSPAT test sequence (10-bit value).
1100 to 1111: unused.
Table 57. JESD204B Link Control Register 4, Address 0x062 (Default 0x00)
Bit No.
[7:0]
Access
RW
Bit Description
Initial lane alignment sequence repeat count. Bits[7:0] specify the number of times the initial lane alignment sequence
repeats. For ADCs, the JESD204B specification states that the initial lane alignment sequence always spans four multiframes
(JESD204B 5.3.3.5). Because Register 0x070, Bits[4:0] determine the number of frames per multiframe, the total number of
frames transmitted during the initial lane alignment sequence = 4 × (Register 0x070[4:0] + 1) × (Register 0x062[7:0] + 1).
Table 58. JESD204B Link Control Register 5, Address 0x063 (Default = 0x80)
Bit No.
7
[6:4]
[3:0]
Access
RW
Bit Description
Reserved
Reserved
JESD204B application layer mode. DDC bandwidth modes are as follows: high bandwidth, decimate by 8 (effective output
bandwidth = fS/10) and low bandwidth, decimate by 16 (effective output bandwidth = fS/20).
0000: generic (no application layer used).
0001: unused.
0010: unused.
0011: unused.
0100: fS × x mode (where x is an integer: 2, 4, 8).
0101 to 0111: unused.
1000: single DDC mode (high bandwidth mode (only DDC0 used).
1001: single DDC mode (low bandwidth mode (only DDC0 used).
1010 to 1011: unused.
1100: dual DDC mode, high bandwidth mode (both DDC 0 and DDC 1 used).
1101: dual DDC mode, low bandwidth mode (both DDC 0 and DDC 1 used).
1110: dual DDC mode, mixed bandwidth mode (DDC 0 high bandwidth mode, DDC 1 low bandwidth mode, samples
repeated).
1111: unused.
Rev. C | Page 60 of 72
Data Sheet
AD9625
Table 59. JESD204B Configuration Register, Address 0x064 (Default = 0x00)
Bit No.
[7:0]
Access
RW
Bit Description
JESD204B serial device identification (DID) number.
Table 60. JESD204B Configuration Register, Address 0x065 (Default = 0x00)
Bit No.
[7:4]
[3:0]
Access
RW
Bit Description
Unused.
JESD204B serial bank identification (BID) number (extension to DID).
Table 61. JESD204B Configuration Register, Address 0x066 (Default = 0x00)
Bit No.
[7:5]
[4:0]
Access
RW
Bit Description
Unused.
JESD204B serial lane identification (LID) number for Lane 0.
Table 62. JESD204B Configuration Register, Address 0x067 (Default = 0x01)
Bit No.
[7:5]
[4:0]
Access
RW
Bit Description
Unused.
JESD204B serial lane identification (LID) number for Lane 1.
Table 63. JESD204B Configuration Register, Address 0x068 (Default = 0x02)
Bit No.
[7:5]
[4:0]
Access
RW
Bit Description
Unused.
JESD204B serial lane identification (LID) number for Lane 2.
Table 64. JESD204B Configuration Register, Address 0x069 (Default = 0x03)
Bit No.
[7:5]
[4:0]
Access
RW
Bit Description
Unused.
JESD204B serial lane identification (LID) number for Lane 3.
Table 65. JESD204B Configuration Register, Address 0x06A (Default = 0x04)
Bit No.
[7:5]
[4:0]
Access
RW
Bit Description
Unused.
JESD204B serial lane identification (LID) number for Lane 4.
Table 66. JESD204B Configuration Register, Address 0x06B (Default = 0x05)
Bit No.
[7:5]
[4:0]
Access
RW
Bit Description
Unused.
JESD204B serial lane identification (LID) number for Lane 5.
Table 67. JESD204B Configuration Register, Address 0x06C (Default = 0x06)
Bit No.
[7:5]
[4:0]
Access
RW
Bit Description
Unused.
JESD204B serial lane identification (LID) number for Lane 6.
Table 68. JESD204B Configuration Register, Address 0x06D (Default = 0x07)
Bit No.
[7:5]
[4:0]
Access
RW
Bit Description
Unused.
JESD204B serial lane identification (LID) number for Lane 7.
Table 69. JESD204B Configuration Register, Address 0x06E (Default = 0x87)
Bit No.
7
[6:5]
Access
RW
Bit Description
JESD204B serial scrambler mode.
0: JESD204B scrambler disabled (SCR = 0).
1: JESD204B scrambler enabled (SCR = 1).
Unused.
Rev. C | Page 61 of 72
AD9625
Bit No.
[4:0]
Data Sheet
Access
RW
Bit Description
JESD204B serial lane control (L = Register 0x06E[4:0] + 1).
0: one lane per link (L = 1).
1: two lanes per link (L = 2).
2: unused.
3: four lanes per link (L = 4).
4: unused.
5: six lanes per link (L = 6).
6: unused.
7: eight lanes per link (L = 8).
8 to 31: unused.
Table 70. JESD204B Configuration Register, Address 0x06F (Default = 0x00)
Bit No.
[7:0]
Access
RO
Bit Description
JESD204B number of octets per frame (F = Register 0x06F[7:0] + 1). These bits are calculated using the
following equation:
F = (Nʹ)/(2 × L)
The following are valid values of F:
M = 1, S = 4, N' = 16, L = 1, F = 8.
M = 1, S = 4, N' = 16, L = 2, F = 4.
M = 1, S = 4, N' = 16, L = 4, F = 2.
M = 1, S = 4, N' = 12, L = 6, F = 1.
M = 1, S = 4, N' = 16, L = 8, F = 1 (default).
Table 71. JESD204B Configuration Register, Address 0x070 (Default = 0x1F)
Bit No.
[7:5]
[4:0]
Access
RW
Bit Description
Unused.
JESD204B number of frames per multiframe (K = Register 0x070[4:0] + 1). Only those values that are divisible
by four can be used.
Table 72. JESD204B Configuration Register, Address 0x071 (Default = 0x00)
Bit No.
[7:0]
Access
RO
Bit Description
JESD204B number of converters per link/device.
0: link connected to one ADC (M = 1).
1 to 255: unused.
Table 73. JESD204B Configuration Register, Address 0x072 (Default = 0x0B)
Bit No.
[7:6]
Access
RW
5
[4:0]
RW
Bit Description
JESD204B number of control bits per sample (CS, based on the JESD204B specification).
00: no control bits sent per sample (CS = 0).
01: one control bit sent per sample, overrange bit enabled (CS = 1).
10: two control bits sent per sample, overrange + timestamp SYSREF bit (CS = 2).
11: reserved.
Unused.
JESD204B converter resolution (N = Register 0x072[4:0] + 1).
0x00 to 0x06: reserved.
0x07 to 0x09: reserved.
0x0A: reserved.
0x0B: N = 12-bit ADC converter resolution.
0x0C to 0x0E: reserved.
0x0F: N = 16-bit ADC converter resolution.
0x10 to 0x1F: reserved.
Rev. C | Page 62 of 72
Data Sheet
AD9625
Table 74. JESD204B Configuration Register, Address 0x073 (Default = 0x2F)
Bit No.
[7:5]
Access
RW
[4:0]
RW
Bit Description
JESD204B device subclass version.
0x0: Subclass 0.
0x1: Subclass 1 (default).
0x2: Subclass 2 (not supported).
0x3: undefined.
JESD204B total number of bits per sample (N' = Register 0x073[4:0] + 1).
0x0 to 0xA: unused.
0xB: N' = 12 (L must be equal to 6).
0xC to 0xE: unused.
0xF: N' = 16 (L must be equal to 1, 2, 4, or 8).
Table 75. JESD204B Configuration Register, Address 0x074 (Default = 0x23)
Bit No.
[7:5]
Access
RW
[4:0]
RO
Bit Description
JESD204B version.
0x0: JESD204A. SYNCINB± pins input are internally gated by the frame clock. SYNCINB± must be low for at least
two frame clock cycles to be interpreted as a synchronization request.
0x1: JESD204B. SYNCINB± pins input are internally gated by the local multiframe clock. SYNCINB± must be low
for at least four frame clock cycles to be interpreted as a synchronization request.
0x2 to 0x7: undefined.
JESD204B samples per converter frame cycle (S = Register 0x074[4:0] + 1). These are read-only bits. For the
AD9625, S must be equal to 4 (Register 0x074[4:0] = 3).
Table 76. JESD204B Configuration Register, Address 0x075 (Default = 0x80)
Bit No.
7
Access
RO
[6:5]
[4:0]
RO
Bit Description
JESD204B high density (HD) format. This is a read-only bit.
0: HD format disabled.
1: HD format enabled. High density mode is automatically enabled based on the values of N' and L.
The values of HD for the AD9625 are as follows:
N' = 16, L = 1, HD = 0.
N' = 16, L = 2, HD = 0.
N' = 16, L = 4, HD = 0.
N' = 12, L = 6, HD = 1.
N' = 16, L = 8, HD = 1 (default).
Unused.
JESD204B Number of control words per frame clock cycle per link (CF). These are read-only bits. For the AD9625,
CF must equal 0 (Register 0x075[4:0] = 0).
Table 77. JESD204B Configuration Register, Address 0x076 (Default = 0x00)
Bit No.
[7:0]
Access
RW
Bit Description
JESD204B Serial Reserved Field 1.
Table 78. JESD204B Configuration Register, Address 0x077 (Default = 0x00)
Bit No.
[7:0]
Access
RW
Bit Description
JESD204B Serial Reserved Field 2.
Table 79. JESD204B Configuration Register, Address 0x078 (Default = 0xC3)
Bit No.
[7:0]
Access
RO
Bit Description
JESD204B serial checksum value for Lane 0. This value is automatically calculated The value = (the sum of all link
configuration parameters for Lane 0) Modulus 256. Checksum is enabled/disabled using Register 0x061, Bit 7.
Table 80. JESD204B Configuration Register, Address 0x079 (Default = 0xC4)
Bit No.
[7:0]
Access
RO
Bit Description
JESD204B serial checksum value for Lane 1. This value is automatically calculated. The value = (the sum of all link
configuration parameters for Lane 1) Modulus 256. Checksum is enabled/disabled using Register 0x061, Bit 7.
Rev. C | Page 63 of 72
AD9625
Data Sheet
Table 81. JESD204B Configuration Register, Address 0x07A (Default = 0xC5)
Bit No.
[7:0]
Access
RO
Bit Description
JESD204B serial checksum value for Lane 2. This value is automatically calculated. The value = (the sum of all link
configuration parameters for Lane 2) Modulus 256. Checksum is enabled/disabled using Register 0x061, Bit 7.
Table 82. JESD204B Configuration Register, Address 0x07B (Default = 0xC6)
Bit No.
[7:0]
Access
RO
Bit Description
JESD204B serial checksum value for Lane 3. This value is automatically calculated. The value = (the sum of all link
configuration parameters for Lane 3) Modulus 256. Checksum is enabled/disabled using Register 0x061, Bit 7.
Table 83. JESD204B Configuration Register, Address 0x07C (Default = 0xC7)
Bit No.
[7:0]
Access
RO
Bit Description
JESD204B serial checksum value for Lane 4. This value is automatically calculated. The value = (the sum of all link
configuration parameters for Lane 4) Modulus 256. Checksum is enabled/disabled using Register 0x061, Bit 7.
Table 84. JESD204B Configuration Register, Address 0x07D (Default = 0xC8)
Bit No.
[7:0]
Access
RO
Bit Description
JESD204B serial checksum value for Lane 5. This value is automatically calculated. The value = (the sum of all link
configuration parameters for Lane 5) Modulus 256. Checksum is enabled/disabled using Register 0x061, Bit 7.
Table 85. JESD204B Configuration Register, Address 0x07E (Default = 0xC9)
Bit No.
[7:0]
Access
RO
Bit Description
JESD204B serial checksum value for Lane 6. This value is automatically calculated. The value = (the sum of all link
configuration parameters for Lane 6) Modulus 256. Checksum is enabled/disabled using Register 0x061, Bit 7.
Table 86. JESD204B Configuration Register, Address 0x07F (Default = 0xCA)
Bit No.
[7:0]
Access
RO
Bit Description
JESD204B serial checksum value for Lane 6. This value is automatically calculated. The value = (the sum of all link
configuration parameters for Lane 6) Modulus 256. Checksum is enabled/disabled using Register 0x061, Bit 7.
Table 87. JESD204B Lane Power-Down Register, Address 0x080 (Default = 0x00)
Bit No.
7
Access
RW
6
RW
5
RW
4
RW
3
RW
2
RW
1
RW
0
RW
Bit Description
Physical Lane H power-down.
0: Lane H enabled.
1: Lane H powered down.
Physical Lane G power-down.
0: Lane G enabled.
1: Lane G powered down.
Physical Lane F power-down.
0: Lane F enabled.
1: Lane F powered down.
Physical Lane E power-down.
0: Lane E enabled.
1: Lane E powered down.
Physical Lane D power-down.
0: Lane D enabled.
1: Lane D powered down.
Physical Lane C power-down.
0: Lane C enabled.
1: Lane C powered down.
Physical Lane B power-down.
0: Lane B enabled.
1: Lane B powered down.
Physical Lane A power-down.
0: Lane A enabled.
1: Lane A powered down.
Rev. C | Page 64 of 72
Data Sheet
AD9625
Table 88. JESD204B Lane Control Register 1, Address 0x082 (Default = 0x10)
Bit No.
7
[6:4]
Access
RW
3
[2:0]
RW
Bit Description
Unused.
Physical Lane B assignment.
000: Logical Lane 0.
001: Logical Lane 1 (default).
010: Logical Lane 2.
011: Logical Lane 3.
100: Logical Lane 4.
101: Logical Lane 5.
110: Logical Lane 6.
111: Logical Lane 7.
Unused.
Physical Lane A assignment.
000: Logical Lane 0 (default).
001: Logical Lane 1.
010: Logical Lane 2.
011: Logical Lane 3.
100: Logical Lane 4.
101: Logical Lane 5.
110: Logical Lane 6.
111: Logical Lane 7.
Table 89. JESD204B Lane Control Register 2, Address 0x083 (Default = 0x32)
Bit No.
7
[6:4]
Access
RW
3
[2:0]
RW
Bit Description
Unused.
Physical Lane D assignment.
000: Logical Lane 0.
001: Logical Lane 1.
010: Logical Lane 2.
011: Logical Lane 3 (default).
100: Logical Lane 4.
101: Logical Lane 5.
110: Logical Lane 6.
111: Logical Lane 7.
Unused.
Physical Lane C assignment.
000: Logical Lane 0.
001: Logical Lane 1.
010: Logical Lane 2 (default).
011: Logical Lane 3.
100: Logical Lane 4.
101: Logical Lane 5.
110: Logical Lane 6.
111: Logical Lane 7.
Rev. C | Page 65 of 72
AD9625
Data Sheet
Table 90. JESD204B Lane Control Register 3, Address 0x084 (Default = 0x54)
Bit No.
7
[6:4]
Access
RW
3
[2:0]
RW
Bit Description
Unused.
Physical Lane F assignment.
000: Logical Lane 0.
001: Logical Lane 1.
010: Logical Lane 2.
011: Logical Lane 3.
100: Logical Lane 4.
101: Logical Lane 5 (default).
110: Logical Lane 6.
111: Logical Lane 7.
Unused.
Physical Lane E assignment.
000: Logical Lane 0.
001: Logical Lane 1.
010: Logical Lane 2.
011: Logical Lane 3.
100: Logical Lane 4 (default).
101: Logical Lane 5.
110: Logical Lane 6.
111: Logical Lane 7.
Table 91. JESD204B Lane Control Register 4, Address 0x085 (Default = 0x76)
Bit No.
7
[6:4]
Access
RW
3
[2:0]
RW
Bit Description
Unused.
Physical Lane H assignment.
000: Logical Lane 0.
001: Logical Lane 1.
010: Logical Lane 2.
011: Logical Lane 3.
100: Logical Lane 4.
101: Logical Lane 5.
110: Logical Lane 6.
111: Logical Lane 7 (default).
Unused.
Physical Lane G assignment.
000: Logical Lane 0.
001: Logical Lane 1.
010: Logical Lane 2.
011: Logical Lane 3.
100: Logical Lane 4.
101: Logical Lane 5.
110: Logical Lane 6 (default).
111: Logical Lane 7.
Table 92. Unused, Address 0x088 (Default = 0x67)
Bit No.
[7:0]
Access
RW
Bit Description
Unused.
Table 93. Unused, Address 0x089 (Default = 0xF0)
Bit No.
[7:0]
Access
RW
Bit Description
Unused.
Rev. C | Page 66 of 72
Data Sheet
AD9625
Table 94. Control Register, Address 0x08A (Default = 0x20)
Bit No.
[7:6]
[5:4]
[3:2]
[1:0]
Access
RW
RW
Bit Description
Unused.
Reserved; Bits[5:4] must be set to 10.
Unused.
Bits[1:0] must be set to 00 for LMFC JESD204B alignment with SYSREF±.
Bits[1:0] must be set to 10 for control bit timestamping with SYSREF±.
Table 95. JESD204B Local Multiframe Clock Offset Control Register, Address 0x08B (Default = 0x00)
Bit No.
[7:5]
[4:0]
Access
RW
Bit Description
Unused.
Local multiframe clock (LMFC) phase offset value. These bits provide the reset value for LMFC phase counter when
SYSREF± pins are asserted; this is used for deterministic delay applications.
Table 96. JESD204B Local Frame Clock Offset Control Register, Address 0x08C (Default = 0x00)
Bit No.
[7:0]
Access
RW
Bit Description
Local frame clock phase offset value. Reset value for frame clock phase counter when SYSREF± pins are asserted. For
the AD9625, only values from 0 to 7 are valid. This is used for deterministic delay applications.
Table 97. DIVCLK± Register, Address 0x0F8 (Default = 0x00)
Bit No.
[7:1]
0
Access
RW
RW
Bit Description
Spare customer register.
Register control to set the ratio between ADC sampling clock and DIVCLK±.
0: divide by 4.
1: not used.
Table 98. Reserved Register, Address 0x0F9
Bit No.
[7:0]
Access
RW
Bit Description
Reserved.
Table 99. Customer Spare Register, Address 0x0FF (Default = 0x00)
Bit No.
[7:1]
0
Access
RW
Bit Description
Unused.
Register map master/slave transfer bit. Self-clearing bit used to synchronize the transfer of data from the master to
the slave registers.
0: no effect.
1: transfers data from the master registers, written by the register maps, to the slave registers.
Table 100. Interrupt Request (IRQ) Status Register, Address 0x100 (Default = 0x00)
Bit No.
7
Access
RO
6
5
4
3
RO
RO
RO
2
RO
1
0
RO
Bit Description
Interrupt request PLL lock error.
1: the PLL is unlocked.
Unused.
Unused.
Unused.
Interrupt request SYSREF± hold error.
1: a hold error has occurred with the last SYSREF± signal received. To clear this error, set and clear Bit 6 in Register
0x03A.
Interrupt request SYSREF± setup error.
1: a setup error has occurred with the last SYSREF± signal received. To clear this error, set and clear Bit 6 in Register 0x03A.
Unused.
Interrupt request clock error.
Rev. C | Page 67 of 72
AD9625
Data Sheet
Table 101. Interrupt Request (IRQ) Mask Control Register, Address 0x101 (Default = 0xBC)
Bit No.
7
Access
RW
6
5
4
3
RW
RW
RW
2
RW
1
0
RW
Bit Description
Interrupt request PLL lock error masked.
1: PLL unlocked events are masked.
Unused.
Must be set to 1.
Must be set to 1.
Interrupt request SYSREF± hold error.
1: a hold error has occurred with the last SYSREF± signal received. To clear this error, set and clear Bit 6 in Register 0x03A.
Interrupt request SYSREF± setup error.
1: a setup error has occurred with the last SYSREF± signal received. To clear this error, set and clear Bit 6 in Register 0x03A.
Unused.
Interrupt request clock error mask.
1: clock error has occurred and the validity of the output data cannot be guaranteed. The only way to recover from this
error is to reset the device.
Table 102. Digital Control Register, Address 0x105 (Default = 0x00)
Bit No.
[7:5]
4
3
2
1
0
Access
RW
RW
RW
RW
RW
Bit Description
Unused.
Must be set to 0.
Must be set to 0.
Must be set to 0.
Must be set to 0.
Must be set to 0.
Table 103. Digital Calibration Threshold Control Register, Address 0x10A (Default = 0x10)
Bit No.
[7:5]
4
[0:3]
Access
RW
Bit Description
Unused.
Enable data set threshold logic for background gain.
Unused.
Table 104. Digital Calibration Data Set Threshold Register, Address 0x10D (Default = 0x3D)
Bit No.
[7:0]
Access
RW
Bit Description
Data set threshold for background gain calibration.
Table 105. Digital Calibration Data Set Threshold Register, Address 0x10E (Default = 0x14)
Bit No.
[7:0]
Access
RW
Bit Description
Data set threshold for background gain calibration.
Table 106. DIVCLK± Output Control Register, Address 0x120 (Default = 0x11)
Bit No.
[7:5]
4
Access
RW
3
RW
2
[1:0]
RW
Bit Description
Unused.
DIVCLK± output disable. DIVCLK± is 1/4th of the sample clock frequency.
0: DIVCLK± output is disabled.
1: DIVCLK± output is enabled.
DIVCLK± output termination selection.
0: DIVCLK± output uses an external 100 Ω resistive termination.
1: DIVCLK± output uses no external resistive termination.
Unused.
Control the differential swing for the DIVCLK± output.
00: 100 mV p-p differential.
01: 200 mV p-p differential.
10: 300 mV p-p differential.
11: 400 mV p-p differential.
Rev. C | Page 68 of 72
Data Sheet
AD9625
Table 107. Trim Setting Control Register, Address 0x121 (Default = 0x00 for AD9625-2.5 and AD9625-2.6; Default = 0x03 for
AD9625-2.0)
Bit No.
[7:2]
[1:0]
Access
RW
Bit Description
Reserved.
Select trim setting, based on sample rate (AD9625-2.0 and AD9625-2.5):
00: Trim 0: for 2.5 GSPS encode rate (default for AD9625-2.5) (not available for AD9625-2.0).
01: Trim 1: for 2.4 GSPS to 2.5 GSPS encode rate (not available for AD9625-2.0).
10: Trim 2: for 2.2 GSPS to 2.4 GSPS encode rate (not available for AD9625-2.0).
11: Trim 3: for 330 MSPS to 2.2 GSPS encode rate (default for AD9625-2.0).
Select trim setting, based on sample rate (AD9625-2.6):
00: Trim 0: for 2.55 GSPS to 2.6 GSPS encode rate (default for AD9625-2.6).
01: Trim 1: for 2.4 GSPS to 2.55 GSPS encode rate.
10: Trim 2: for 2.2 GSPS to 2.4 GSPS encode rate.
11: Trim 3: for 330 MSPS to 2.2 GSPS encode rate.
Table 108. Unused Register, Address 0x12A (Default = 0x05)
Bit No.
[7:0]
Access
RW
Bit Description
Reserved; maintain default setting of 0x05.
Table 109. DDC 0 Gain Control Register, Address 0x130 (Default = 0x00)
Bit No.
[7:6]
[5:4]
Access
RW
[3:2]
[1:0]
RW
Bit Description
Unused.
DDC 0 polyphase (decimate by 2) gain in units of 6 dB.
00: 0 dB gain.
01: 6 dB gain.
10: 12 dB gain.
11: 18 dB gain.
Unused.
DDC 0 polyphase (decimate by 8) gain in units of 6 dB.
00: 0 dB gain.
01: 6 dB gain.
10: 12 dB gain.
11: 18 dB gain.
Table 110. DDC 0 Phase Increment Least Significant Bits Register, Address 0x131 (Default = 0x00)
Bit No.
[7:0]
Access
RW
Bit Description
DDC 0 NCO phase increment value. Phase increment for the NCO within DDC 0 (Bits[7:0]).
The output frequency = (decimal(Register 0x132[1:0]; Register 0x131[7:0]) × fS)/1024.
Table 111. DDC 0 Phase Increment Most Significant Bits Register, Address 0x132 (Default = 0x00)
Bit No.
[7:2]
[1:0]
Access
RW
Bit Description
Unused.
DDC 0 NCO phase increment value. Phase increment for the NCO within DDC 0 (Bits[9:8]).
Table 112. DDC 1 Gain Control Register, Address 0x138 (Default = 0x00)
Bit No.
[7:6]
[5:4]
[3:2]
Access
RW
Bit Description
Unused.
DDC 1 polyphase (decimate by 2) gain in units of 6 dB.
00: 0 dB gain.
01: 6 dB gain.
10: 12 dB gain.
11: 18 dB gain.
Unused.
Rev. C | Page 69 of 72
AD9625
Bit No.
[1:0]
Access
RW
Data Sheet
Bit Description
DDC 1 polyphase (decimate by 8) gain in units of 6 dB.
00: 0 dB gain.
01: 6 dB gain
10: 12 dB gain.
11: 18 dB gain.
Table 113. DDC 1 Phase Increment Least Significant Bits Register, Address 0x139 (Default = 0x00)
Bit No.
[7:0]
Access
RW
Bit Description
DDC 1 NCO phase increment value. Phase increment for the NCO within DDC 1 (Bits[7:0]).
The output frequency = (decimal(Register 0x13A[1:0]; Register 0x139[7:0]) × fS)/1024.
Table 114. DDC 1 Phase Increment Most Significant Bits Register, Address 0x13A (Default = 0x00)
Bit No.
[7:2]
[1:0]
Access
RW
Bit Description
Unused.
DDC1 NCO phase increment value (Bits[9:8]).
Table 115. SYSREF±Hold Time Guardband Register, Address 0x13B (Default = 0x00)
Bit No.
[7:5]
Access
RW
[4:0]
RW
Bit Description
These bits increase the SYSREF± hold time guardband that is used to assert the SYSREF± hold IRQ flag in register
0x100[3]. This time is informational only and does not change the actual hold time for SYSREF±.
000: No additional guardband hold time.
001: 35 ps of additional hold time guardband for 0x100[3].
010: 70 ps of additional hold time guardband for 0x100[3].
011: 105 ps of additional hold time guardband for 0x100[3].
100: 140 ps of additional hold time guardband for 0x100[3].
101: 175 ps of additional hold time guardband for 0x100[3].
110: 210 ps of additional hold time guardband for 0x100[3].
111: 245 ps of additional hold time guardband for 0x100[3].
Reserved.
Table 116. SYSREF± Setup Time Guardband Register, Address 0x13C (Default = 0x00)
Bit No.
[7:5]
Access
RW
[4:0]
RW
Bit Description
These bits increase the SYSREF± setup time guardband that is used to assert the SYSREF± setup IRQ flag in register
0x100[2]. This time is informational only and does not change the actual setup time for SYSREF±.
000: No additional guardband setup time.
001: 35 ps of additional setup time guardband for 0x100[2].
010: 70 ps of additional setup time guardband for 0x100[2].
011: 105 ps of additional setup time guardband for 0x100[2].
100: 140 ps of additional setup time guardband for 0x100[2].
101: 175 ps of additional setup time guardband for 0x100[2].
110: 210 ps of additional setup time guardband for 0x100[2].
111: 245 ps of additional setup time guardband for 0x100[2].
Reserved.
Rev. C | Page 70 of 72
Data Sheet
AD9625
APPLICATIONS INFORMATION
DESIGN GUIDELINES
CLOCK STABILITY CONSIDERATIONS
Before starting system level design and layout of the AD9625, it
is recommended that the designer become familiar with these
guidelines, which discuss the special circuit connections and
layout requirements needed for certain pins.
When powered on, the AD9625 enters an initialization phase
during which an internal state machine sets up the biases and
the registers for proper operation. During the initialization
process, the AD9625 needs a stable clock. If the ADC clock
source is not present or not stable during ADC power-up, it
disrupts the state machine and causes the ADC to start up in
a less than optimum state. To correct this, an initialization
sequence must be invoked after the ADC clock is stable or any
change in the sampling clock frequency is made. By issuing a
digital reset via Register 0x00. The pseudo code sequence for a
digital reset is as follows:
POWER AND GROUND RECOMMENDATIONS
When connecting power to the AD9625, it is recommended
that separate supplies are used: one supply for the analog output
(AVDD), and a separate supply for the digital outputs (DRVDD
and DVDD). The designer can use several different decoupling
capacitors to cover both high and low frequencies. Locate these
capacitors close to the point of entry at the PCB level and close
to the pins of the part with minimal trace length.
When using the AD9625, a single PCB ground plane is
sufficient. With proper decoupling and smart partitioning
of the PCB analog, digital, and clock sections, optimum
performance is easily achieved.
#Stable Clock at the input to the AD9625
SPI_Write (0x00, 0x3C); # Reset
SPI_Write (0x080 0xFF) #SPI register transfer
SPI_Write (0x00, 0x00); # Clear Reset
SPI_Write (0x080 0xFF) #SPI register transfer
#Write further configurations
SPI PORT
When the full dynamic performance of the converter is
required, do not activate the SPI port. Because the SCLK, CSB,
and SDIO signals are typically asynchronous to the ADC clock,
noise from these signals can degrade converter performance.
If the on-board SPI bus is used for other devices, it may be
necessary to provide buffers between this bus and the AD9625
to keep these signals from transitioning at the converter input
pins during critical sampling periods.
Rev. C | Page 71 of 72
AD9625
Data Sheet
OUTLINE DIMENSIONS
7.50
REF SQ
11.20 SQ
TOP VIEW
1.70
1.59
1.50
A
B
C
D
E
F
G
H
J
K
L
M
N
P
10.40 SQ
0.80
BOTTOM VIEW
0.80 REF
DETAIL A
SIDE VIEW
0.75
REF
DETAIL A
1.33
1.26
1.19
0.38
0.33
0.28
0.51 REF
SEATING
PLANE
PKG-004709
A1 BALL
PAD CORNER
14 13 12 11 10 9 8 7 6 5 4 3 2 1
0.50
0.45
0.40
BALL DIAMETER
COPLANARITY
0.12
12-07-2015-B
A1 BALL
PAD CORNER
12.10
12.00 SQ
11.90
COMPLIANT TO JEDEC STANDARDS MO-275-GGAB-1.
Figure 107. 196-Ball Ball Grid Array, Thermally Enhanced [BGA_ED]
(BP-196-2)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
AD9625BBPZ-2.5
AD9625BBPZ-2.0
AD9625BBPZ-2.6
AD9625BBP-2.6
AD9625BBP-2.5
AD9625BBPZRL-2.5
AD9625BBPZRL-2.0
AD9625BBPRL-2.5
AD9625BBPRL-2.6
AD9625-2.6EB
AD9625-2.5EBZ
AD9625-2.0EBZ
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
196-Ball Ball Grid Array, Thermally Enhanced [BGA_ED]
196-Ball Ball Grid Array, Thermally Enhanced [BGA_ED]
196-Ball Ball Grid Array, Thermally Enhanced [BGA_ED]
196-Ball Ball Grid Array, PbSn, Thermally Enhanced [BGA_ED]
196-Ball Ball Grid Array, PbSn, Thermally Enhanced [BGA_ED]
196-Ball Ball Grid Array, Thermally Enhanced [BGA_ED], 13” Tape and Reel
196-Ball Ball Grid Array, Thermally Enhanced [BGA_ED], 13” Tape and Reel
196-Ball BGA, PbSn, Thermally Enhanced [BGA_ED], 13” Tape and Reel
196-Ball BGA, PbSn, Thermally Enhanced [BGA_ED], 13” Tape and Reel
Evaluation Board with AD9625
Evaluation Board with AD9625
Evaluation Board with AD9625
Package Option
BP-196-2
BP-196-2
BP-196-2
BP-196-2
BP-196-2
BP-196-2
BP-196-2
BP-196-2
BP-196-2
Z = RoHS Compliant Part.
©2014–2016 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D11814-0-9/16(C)
www.analog.com/AD9625
Rev. C | Page 72 of 72
Similar pages