MPD MB1524S-12ERU Low cost, 1 x 2 inch 15w, 4:1 input range dc/dc converter Datasheet

MB1500ERU
Low Cost, 1 x 2 Inch
15W, 4:1 Input Range
DC/DC Converters
Electrical Specifications
Key Features:
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
• 15W Output Power
Input
Parameter
• 4:1 Input Voltage Range
Input Voltage Range
• 1,500 VDC Isolation
• Single & Dual Outputs
Input Start Voltage
• Efficiency to 90%
Input Filter
Start-Up Time
• Compact 1 x 2 Inch Case
Output
• -40°C to +85°C Operation
• Industry Standard Pin-Out
• Low Cost
Parameter
Output Voltage Accuracy
Output Voltage Balance
Output Trim Range
Line Regulation
Load Regulation
Cross Regulation
Ripple & Noise (20 MHz)
Transient Recovery Time, See Note 5
Transient Response Deviation
Output Power Protection
Temperature Coefficient
Output Short Circuit, See Note 6
Conditions
Min.
24 VDC Input
9.0
48 VDC Input 18.0
24 VDC Input
48 VDC Input
(Pi) Filter
See Note 2
Typ.
24.0
48.0
Conditions
Typ.
±1.0
±0.5
±10
±0.2
±0.5
Min.
Dual Outputs, Balanced Loads
VIN = Min to Max
IOUT = 10% to 100%
See Note 3
See Note 4
Max.
36.0
75.0
9.0
17.8
10
70
300
25% Load Step Change
±3.0
160
±0.02
Continuous (Autorecovery)
Units
VDC
VDC
mS
Max.
±3.0
±1.0
±0.5
±1.0
±5.0
100
500
±5.0
Units
%
%
%
%
%
mV P - P
µSec
%
%
%/°C
General
Parameter
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
Conditions
60 Seconds
500 VDC
See Note 7
Min.
1,500
1,000
Typ.
Max.
Units
VDC
M
pF
kHz
Max.
+85
+105
+125
Units
°C
°C
°C
95
%
1,000
300
Environmental
Parameter
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Physical
Case Size
Case Material
Weight
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
Conditions
Ambient
Case
Min.
-40
Typ.
+25
-55
Free Air Convection
RH, Non-condensing
See Mechanical Diagram (Page 4)
Aluminum Alloy With Non-Conductive Base (UL94-V0)
0.99 Oz (28g)
Remote On/Off
Parameter
Unit On
Unit Off
Off Idle Current
Conditions
See Note 8
See Note 8
Min.
2.5
0
Typ.
Max.
12.0
1.2
1.0
Units
VDC
VDC
mA
Reliability Specifications
Parameter
MTBF
Vibration
Conditions
Min.
Typ.
Max.
MIL HDBK 217F, 25°C, Gnd Benign
1.0
10 - 55 Hz, 10G, 30 Min, on X, Y & Z Axis
Units
MHours
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Lead Temperature
Conditions
24 VDC Input
48 VDC Input
1.5 mm From Case for 10 Sec
Min.
-0.7
-0.7
Typ.
Max.
50.0
100.0
300
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com
Units
VDC
°C
www.micropowerdirect.com
Model Selection Guide
Input
Model
Number
Voltage (VDC)
Nominal
Range
Output
Current (mA)
Voltage
Current
Current
Full-Load No-Load
(VDC)
(mA, Max)
(mA, Min)
Efficiency
(%, Typ)
Over
Fuse
Voltage Capacitive
Rating
Load
Protection (µF, Max)
Slow-Blow
(VDC Typ)
(mA)
MB1524S-03ERU
24
9.0 - 36.0
633
45
3.3
4,000
200
87
3.9
10,200
1,500
MB1524S-05ERU
24
9.0 - 36.0
695
45
5.0
3,000
150
90
6.2
4,020
1,500
MB1524S-12ERU
24
9.0 - 36.0
703
15
12.0
1,250
63
89
15.0
1,035
1,500
MB1524S-15ERU
24
9.0 - 36.0
703
15
15.0
1,000
50
89
18.0
705
1,500
MB1524S-24ERU
24
9.0 - 36.0
695
20
24.0
625
31
90
30.0
470
1,500
MB1524D-05ERU
24
9.0 - 36.0
727
20
±5.0
±1,500
±75
86
±6.2
4,800
1,500
MB1524D-12ERU
24
9.0 - 36.0
710
15
±12.0
±625
±32
88
±15.0
800
1,500
MB1524D-15ERU
24
9.0 - 36.0
710
15
±15.0
±500
±25
88
±18.0
500
1,500
MB1548S-03ERU
48
18.0 - 75.0
316
35
3.3
4,000
200
87
3.9
10,200
1,000
MB1548S-05ERU
48
18.0 - 75.0
351
35
5.0
3,000
150
89
6.2
4,020
1,000
MB1548S-12ERU
48
18.0 - 75.0
355
10
12.0
1,250
63
88
15.0
1,035
1,000
MB1548S-15ERU
48
18.0 - 75.0
347
10
15.0
1,000
50
90
18.0
705
1,000
MB1548D-05ERU
48
18.0 - 75.0
363
20
±5.0
±1,500
±75
86
±6.2
4,800
1,000
MB1548D-12ERU
48
18.0 - 75.0
355
15
±12.0
±625
±32
88
±15.0
800
1,000
MB1548D-15ERU
48
18.0 - 75.0
351
15
±15.0
±500
±25
89
±18.0
500
1,000
Notes:
1. The specified maximum capacitive load is for each output.
2. Start up time is measured at nominal input and with a constant resistive load.
3. Cross regulation is measured with the main output set at 50% load. The second output is varied
from 10% to 100% load.
4. When measuring output ripple, it is recommended that an external ceramic capacitor (approx
1 µF to 10 µF) be placed from the +VOUT to the -VOUT pins.
5. Transient recovery is measured to within a 1% error band for a load step change of 25%.
6. Short circuit protection is provided by a “hiccup mode” circuit.
7. Isolation capacitance for 24 VDC output models is 2,000 pF. Isolation capacitance is measured
from input to output at 100 kHz/0.1V.
8. The control input (pin 6) is referenced to the -VIN (pin 2) input. If it is grounded, the unit will
shut off.
9. These units should not be operated with a load under 10% of full load. Operation at no-load will
not damage the unit, but they may not meet all specifications.
10. These units should not be operated over +85°C. Exceeding +85°C may damage the unit.
11. It is recommended that a fuse be used on the input of a power supply for protection. See the
Model Selection table above for the correct rating.
Derating Curve
External Trim
External Trim Notes:
On single output units, an external resistor can be used to adjust the converter
output up/down by about 10%. The connection is shown in the diagram at left. The
required resistor value is calculated by the formulas:
Trim UP = RTRIM = A $-R2 - R3
R2 A
Trim Down = RTRIM = A $-R1 - R3
R1 A
Where A =
VREF
$ R1
VTRIM - VREF
Where A = VTRIM VREF $ R2
VREF
Where RTRIM = The value of the external trim resistor
VTRIM = The amount of voltage adjustment required
The value of R1, R2, R3 and VREF are given in the table below.
Parameter
Output Voltage (VDC)
3.3
5.0
9.0
12
15
24
R1 (k)
4.801
2.883
7.500
10.971
14.497
24.872
R2 (k)
2.863
2.864
2.864
2.864
2.864
2.864
R3 (k)
15.00
10.00
15.00
17.80
17.80
20.00
VREF (V)
1.24
2.50
2.50
2.50
2.50
2.50
If not used, the Trim pin (pin 4) should be left open. Please contact the factory for more information.
292 Page Street Ste D Stoughton, MA 02072
• TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]
www.micropowerdirect.com
EMC Specifications
Parameter
Radiated Emissions
Conducted Emissions
ESD
RS
EFT
Surge
CS
Voltage Dips
Standard
See Note 1
EN 55022
See Note 1
EN 55022
EN 61000-4-2
EN 61000-4-3
See Note 2
EN 61000-4-4
See Note 3
EN 61000-4-5
EN 61000-4-6
EN 61000-4-29
Class A
Class A
Criteria B; ±4 kV Contact
Criteria A; 10V/m
Criteria B; ±2 kV
Criteria B; ±2 kV
Criteria A; 3 Vrms
Criteria B; 0% - 70%
Notes:
1. All units are rated for EN 55022 (CE/RE) class A without external components.
They will meet class B with the addition of the MDCFM-02A(W) (or a similar
discrete filter circuit). Contact the factory for more information.
2. To meet the requirements of EN 61000-4-4 (±2 kV), external components
are needed. This can be done discretely, or with the addition of the MDCFM02A(W). Contact the factory for more information.
3. To meet the requirements of EN 61000-4-5 (±2 kV), external components are
needed. This can be done discretely, or with the addition of the MDCFM-02(W).
Contact the factory for more information.
Typical Connection
7. In many applications simply adding input/output capacitors will
The diagram above illustrates a typical connection of the MB1500ERU 5. Recommended values for components are:
enhance the input surge proseries for applications that require meeting EMC standards. The units do not Component
48 VIN
24 VIN
Vin
Input
Vout
Output
tection and reduce output
require external components to operate as specified. Some notes on this
MOV
S14K35
S14K60
(VDC) Capacitor (VDC) Capacitor
ripple sufficiently. The input
diagram (starting with the input circuit) are:
L1
56 µH
56 µH
capacitor C1 and output cap1. It is recommended that an external fuse be used. The recommended fuse
3.3
470 µF
330 µF
acitors C3 and C4 shown in the 24
is shown in the model chart on page 2.
TVS
SMCJ48A
SMCJ90A
5.0
470 µF
typical connection diagram
2. An external MOV is recommended on the input to protect the unit in the
C1
330 µF/50V
330 µF/100V
12
220 µF
48
330 µF
above (and board layout
event of a surge. A recommended value is given in the table at right.
15
220 µF
C2
1.0 µF/50V
1.0 µF/100V
drawings below) illustrate
3. An external TVS is recommended on the input to protect the unit in the
24
100 µF
L2
4.7 µH
4.7 µH
their connection. Recommended capacitor
event of a voltage spike. A recommended value is given in the table at
±5
±220 µF
CY1, CY2
1,000 pF/2 kV
1,000 pF/2 kV
values are given in the table at right.
right.
±12
±100 µF
4. The output filtering capacitor (C3) is a high frequency, low resistance
±15
±100 µF
electrolytic capacitor. Care must be taken in choosing this capacitor not 6. Input noise and surge suppression modules are available for a
number of MPD DC/DC power supplies. For pricing or full technito exceed the capacitive load specification for the unit. The board layout
cal information on these modules please contact the factory.
illustration below shows a connection for dual output units. Voltage derating
of capacitors should be 80% or above.
Typical Board Layout: With External Filter/Surge Components for Single Output Unit
Typical Connection: With External Filter/Surge Components for Dual Output Unit
MicroPower Direct
•
292 Page Street Ste D Stoughton, MA 02072
• TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]
www.micropowerdirect.com
Mechanical Dimensions
Pin Connections
Pin
1
2
3
4
5
6
Single Output
+VIN
-VIN
+VOUT
Trim
-VOUT
Remote On/Off
Pin
1
2
3
4
5
6
Dual Output
+VIN
-VIN
+VOUT
Common
-VOUT
Remote On/Off
Adapter Plate
Mechanical Dimensions: With Optional Heatsink
All models of the MB1500x-xxERU series are available
mounted on an adapter plate similar to the one pictured at left. The
adapter plate makes it easier to mount the unit to a chassis or to a
standard DIN rail. Please contact the factory for more information.
For the heatsink option, add suffix “H” to the
model number (i.e. MB1524S-05ERU-H)
MicroPower Direct
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.02 (±0.50)
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: [email protected]
Similar pages