CDE MLSG682M020JA0C Aluminum electrolytic Datasheet

Type MLSG – Slimpack, 5000 hr@125 ºC, Aluminum Electrolytic
With a profile of 1.0” by 0.5” type MLSG Slimpack capacitors fit into the
tightest of spaces and meets a DC test of 5000 hrs at rated voltage,
125 ºC. MLSG Slimpack is a perfect fit for military and aerospace
applications requiring a low profile, rugged design and long-life.
Specify type HRMLSG for high reliability burn-in.
Highlights
-
5000 hrs @ rated voltage, 125 °C
Stainless steel case
Withstands more than 80,000 feet altitude
80 g vibration
Type HR, high reliability burn-in
Specifications
Temperature Range
–55 °C to +125 °C
Rated Voltage Range
10 Vdc to 250 Vdc
Capacitance Range
140 µF to 24,000 µF
Capacitance Tolerance
±20%
Leakage Current
≤ 0.002 CV µA, @ 25 °C and 5 mins.
Ripple Current Multipliers
Case Temperature
45 °C 55 °C 65 °C 75 °C 85 °C
95 °C 105 °C 115 °C 125 °C
1.41
0.87
1.32
1.22
1.12
1.00
0.71
0.50
0.00
Ambient Temperature, No Heatsink
45 °C
55 °C
65 °C
75 °C
85 °C 95 °C 105 °C 115 °C 125 °C
0.63
0.58
Frequency
0.54
0.49
0.44
50 Hz
0.38
60 Hz 120 Hz 360 Hz
0.31
0.00
1 kHz
5 kHz
10 kHz &
up
5 to 40 V
0.95
0.96
1.00
1.03
1.04
1.04
1.04
60 to 250 V
0.80
0.84
1.00
1.18
1.25
1.30
1.30
Low Temperature Characteristics
Impedance ratio: Z–55 ⁰C ∕ Z+25 ⁰C @ 120 Hz
≤ 10 (5 - 20 Vdc)
≤ 2 (25 - 250 Vdc)
DC Life Test
5000 h at rated voltage @ 125 °C
D Capacitance +/- 15% less than or equal to 60 Vdc
D Capacitance +/- 10% greater than 60 Vdc
ESR 200% of limit
DCL 100% of limit
Shelf Life Test
500 h @ 125 °C
Capacitance 100% of limit
ESR 100% of limit
DCL 100% of limit
Vibration
MIL-STD-202, Meth. 204, Sine Swept. IEC 60068-2-6
JK Case = 80g
All Others = 50g
Mounting: Vibration capability is dependent upon mounting restraint.
0.22
CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800
Type MLSG – Slimpack, 5000 hr@125 ºC, Aluminum Electrolytic
Vibration Test
Level
The specimens, while deenergized or operating under the load conditions
specified, shall be subjected to the vibration amplitude, frequency range,
and duration specified for each case size.
Amplitude
The specimens shall be subjected to a simple harmonic motion having an
amplitude of either 0.06-inch double amplitude (maximum total excursion)
or peak level specified above (XXg peak), whichever is less. The tolerance
on vibration amplitude shall be ±10 percent.
Frequency Range
The vibration frequency shall be varied logarithmically between the
approximate limits of 10 to 2,000 Hz.
Sweep Time and Duration
The entire frequency range of 10 to 2,000 Hz and return to 10 Hz shall be
traversed in 20 minutes. This cycle shall be performed 12 times in each
of three mutually perpendicular directions (total of 36 times), so that
the motion shall be applied for a total period of approximately 12 hours.
Interruptions are permitted provided the requirements for rate of change
and test duration are met.
High Reliability Test/Burn-in
Established Reliability capacitors shall be subjected to a minimum of 100
percent of the dc rated voltage at 85 ºC for 48 hours minimum but not to
exceed 96 hours. During this test, capacitors shall be adequately protected
against temporary voltage surges of 10 percent or more of the test voltage.
After burn-in, the capacitors shall be returned to room ambient conditions
and the dc leakage, capacitance, and ESR shall be measured with respect
to specified limits.
Thermal Resistance
Large Sides
Heatsinked
Case Length
1.5"
2.0"
2.5”
3.0"
Insulation
ºC/W
ºC/W
ºC/W
ºC/W
None
6.6
4.8
3.8
3.1
Polyester
7.2
5.3
4.2
3.4
None
4.4
3.1
2.4
2
Polyester
4.7
3.3
2.6
2.2
one
both
ESL
≤30 nH measured 1/4” from case at 1 MHz
Typical Weight
Case JK = 30
Case JA = 39
Case JH = 48
Case JB = 57
Terminals
18 AWG copper wire with 60/40 tin-lead electroplate, 20 amps max
Case Material
Stainless Steel
Ripple Current Capability
The ripple current capability is set by the maximum permissible internal
core temperature, 125 ºC.
Air Cooled
The ripple currents in the ratings tables are for 85 ºC case temperatures.
For air temperatures without a heatsink use the multipliers Ambient
Temperature, No Heatsink.
Heatsink Cooled
Temperature rise from the internal hottest spot, the core, to ambient air is
∆T = I2(ESR)(θcc + θca), recommended max ΔT of 30 ºC
where θcc is the thermal resistance from core to case and θca from case to
ambient. To calculate maximum ripple capability with the MLS attached to a
heatsink use the maximum core temperature and the values for θcc.
Example
As an illustration, suppose you operate an insulated MLSG262M060JB0C
in 95 ºC air and attach it to a commercial heatsink with a free-air thermal
resistance of 2.7 ºC/W. Use a good thermal grease between the MLS and
the heatsink, and the total thermal resistance is 2.7 +3. 4 or 6.1º C/W. The
power which would heat the core to 125 °C is (125 - 95)/6. 1 or 4.9 W. For an
ESR of 47 mΩ, 4.9 W equates to a ripple current of 10.2 A.
CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800
Type MLSG – Slimpack, 5000 hr@125 ºC, Aluminum Electrolytic
Part Numbering System
HR
MLSG
821
Optional
Type
Capacitance
High
Reliability
MLSG
191 = 190 µF
102 = 1000 µF
Examples:
Standard MLSG: MLSG191M200JK0C
High Reliability: HRMLSG191M200JK0C
M
200
JB
0
A
Tolerance Rated Voltage
Case Code
Insulation
Mounting Style
M=±20%
JK, L=1.5 in.
JA, L=2.0 in
JH, L=2.5 in
JB, L=3.0 in.
* other sizes
available
0 = bare can
1 = polyester
005 = 5 Vdc
7R5 = 7.5 Vdc
200 = 200 Vdc
C = two leads
Outline Drawing
Note: The polyester tape wrap may add up to 0.020 inches to the thickness and width of the capacitor.
CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800
Type MLSG – Slimpack, 5000 hr@125 ºC, Aluminum Electrolytic
Ratings
10 Vdc @ 125 °C
12 Vdc @ 105 °C
15 Vdc Surge @ 25 °C
20 Vdc @ 125 °C
24 Vdc @ 105 °C
30 Vdc Surge @ 25 °C
30 Vdc @ 125 °C
36 Vdc @ 105 °C
45 Vdc Surge @ 25 °C
40 Vdc @ 125 °C
48 Vdc @ 105 °C
60 Vdc Surge @ 25 °C
50 Vdc @ 125 °C
60 Vdc @ 105 °C
75 Vdc Surge @ 25 °C
60 Vdc @ 125 °C
60 Vdc @ 105 °C
90 Vdc Surge @ 25 °C
75 Vdc @ 125 °C
90 Vdc @ 105 °C
112 Vdc Surge @ 25 °C
100 Vdc @ 125 °C
120 Vdc @ 105 °C
150 Vdc Surge @ 25 °C
150 Vdc @ 125 °C
180 Vdc @ 105 °C
225 Vdc Surge @ 25 °C
200 Vdc @ 125 °C
250 Vdc @ 105 °C
300 Vdc Surge @ 25 °C
250 Vdc @ 125 °C
275 Vdc @ 105 °C
350 Vdc Surge @ 25 °C
Cap
Part
Number
Ω 120 Hz
25 ºC
Cat. ESR
Ω 10 KHz
25 ºC
Cat. ESR
Ripple (A)
Ripple (A)
Surge 25 ºC
Case @ 85°C Case @ 85°C
Vdc
120Hz
10kHz
9500
MLSG952M010JK0C
0.096
0.091
6.9
7.1
14000
MLSG143M010JA0C
0.068
0.064
9.8
19000
MLSG193M010JH0C
0.053
0.050
24000
MLSG243M010JB0C
0.042
4600
MLSG462M020JK0C
6800
MLSG682M020JA0C
Case
Length
105 ºC
Vdc
15
1.5
12
10
15
2
12
12.6
12.9
15
2.5
12
0.040
15.4
15.8
15
3
12
0.102
0.097
6.6
6.8
30
1.5
24
0.072
0.068
9.4
9.7
30
2
24
9300
MLSG932M020JH0C
0.054
0.052
12.3
12.6
30
2.5
24
11000
MLSG113M020JB0C
0.042
0.040
15.2
15.6
30
3
24
3300
MLSG332M030JK0C
0.103
0.098
6.6
6.8
45
1.5
36
4900
MLSG492M030JA0C
0.072
0.069
9.5
9.7
45
2
36
6700
MLSG672M030JH0C
0.055
0.053
12.3
12.6
45
2.5
36
8500
MLSG852M030JB0C
0.043
0.041
14.9
15.3
45
3
36
2300
MLSG232M040JK0C
0.105
0.100
6.6
6.8
60
1.5
48
3400
MLSG342M040JA0C
0.072
0.068
9.5
9.7
60
2
48
4600
MLSG462M040JH0C
0.056
0.053
12.3
12.6
60
2.5
48
5900
MLSG592M040JB0C
0.045
0.043
14.9
15.3
60
3
48
1600
MLSG162M050JK0C
0.108
0.101
6.6
6.8
75
1.5
60
2500
MLSG252M050JA0C
0.073
0.700
9.5
9.7
75
2
60
3400
MLSG342M050JH0C
0.056
0.053
12.3
12.6
75
2.5
60
4300
MLSG432M050JB0C
0.046
0.043
14.9
15.3
75
3
60
1000
MLSG102M060JK0C
0.109
0.103
6.5
6.6
90
1.5
72
1500
MLSG152M060JA0C
0.074
0.071
9.3
9.6
90
2
72
2100
MLSG212M060JH0C
0.057
0.054
12.1
12.4
90
2.5
72
2600
MLSG262M060JB0C
0.047
0.044
14.7
15
90
3
72
790
MLSG791M075JK0C
0.246
0.234
4.0
4.2
112.5
1.5
90
1100
MLSG112M075JA0C
0.200
0.190
5.0
5.2
112.5
2
90
1500
MLSG152M075JH0C
0.148
0.141
6.2
6.5
112.5
2.5
90
2000
MLSG202M075JB0C
0.096
0.091
8.2
8.5
112.5
3
90
400
MLSG401M100JK0C
0.960
0.768
2
2.4
150
1.5
120
600
MLSG601M100JA0C
0.634
0.507
2.8
3.6
150
2
120
800
MLSG801M100JH0C
0.484
0.387
3.6
4.6
150
2.5
120
1000
MLSG102M100JB0C
0.387
0.310
4.4
5.7
150
3
120
200
MLSG201M150JK0C
0.960
0.768
2
2.4
225
1.5
180
300
MLSG301M150JA0C
0.634
0.507
2.8
3.6
225
2
180
400
MLSG401M150JH0C
0.484
0.387
3.6
4.6
225
2.5
180
500
MLSG501M150JB0C
0.387
0.310
4.4
5.7
225
3
180
190
MLSG191M200JK0C
1.274
1.019
1.9
2.1
300
1.5
250
280
MLSG281M200JA0C
0.845
0.676
2.8
3.1
300
2
250
380
MLSG381M200JH0C
0.634
0.508
3.6
4.1
300
2.5
250
490
MLSG491M200JB0C
0.507
0.406
4.4
5
300
3
250
140
MLSG141M250JK0C
1.200
0.960
1.9
2.2
350
1.5
300
220
MLSG221M250JA0C
0.792
0.634
2.9
3.2
350
2
300
300
MLSG301M250JH0C
0.605
0.484
3.7
4.2
350
2.5
300
380
MLSG381M250JB0C
0.484
0.387
4.5
5.1
350
3
300
CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800
Type MLSG – Slimpack, 5000 hr@125 ºC, Aluminum Electrolytic
Typical Performance Curves
Part # MLSG122M060JKOC
Cap vs. Frequency & Temp
1.2
Ratio to 25°C, 120 Hz Value
1.0
0.8
0.6
0.4
0.2
0.0
10
100
1000
10000
100000
1000000
Freq (Hz)
125
105
85
65
45
25
0
-20
-40
-55
ESR vs. Frequency & Temp
Ratio to 25°C, 120 Hz Value
10.0
1.0
0.1
0.01
1
10
125
100
105
85
1000
Freq (Hz)
65
45
25
10000
0
-20
100000
-40
1000000
-55
|Z| vs. Frequency & Temp
Ratio to 25°C, 120 Hz Value
100.0
10.0
1.0
0.1
0.01
1
10
125
100
105
85
1000
Freq (Hz)
65
45
25
10000
0
-20
100000
-40
1000000
-55
CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800
Type MLSG – Slimpack, 5000 hr@125 ºC, Aluminum Electrolytic
Typical Performance Curves
Type MLSG Operating Life in Kilohours vs Ripple Current
Expected Operating Life, kh
1000
55°C
100
65°C
75°C
85°C
95°C
105°
10
115°C
1
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.1
1.2
1.3
1.4
1.5
Rated Ripple-Current Multiple
Type MLSG Operating Life in Years vs Ripple Current
Expected Operating Life, years
100
55°C
65°C
75°C
10
85°C
95°C
105°
115°C
1
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.1
1.2
1.3
1.4
1.5
Rated Ripple-Current Multiple
CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800
Notice and Disclaimer: All product drawings, descriptions, specifications, statements, information and
data (collectively, the “Information”) in this datasheet or other publication are subject to change. The
customer is responsible for checking, confirming and verifying the extent to which the Information contained in this datasheet or other publication is applicable to an order at the time the order is placed. All
Information given herein is believed to be accurate and reliable, but it is presented without any guarantee, warranty, representation or responsibility of any kind, expressed or implied. Statements of suitability
for certain applications are based on the knowledge that the Cornell Dubilier company providing such
statements (“Cornell Dubilier”) has of operating conditions that such Cornell Dubilier company regards
as typical for such applications, but are not intended to constitute any guarantee, warranty or representation regarding any such matter – and Cornell Dubilier specifically and expressly disclaims any guarantee,
warranty or representation concerning the suitability for a specific customer application, use, storage,
transportation, or operating environment. The Information is intended for use only by customers who
have the requisite experience and capability to determine the correct products for their application. Any
technical advice inferred from this Information or otherwise provided by Cornell Dubilier with reference
to the use of any Cornell Dubilier products is given gratis (unless otherwise specified by Cornell Dubilier),
and Cornell Dubilier assumes no obligation or liability for the advice given or results obtained. Although
Cornell Dubilier strives to apply the most stringent quality and safety standards regarding the design
and manufacturing of its products, in light of the current state of the art, isolated component failures may
still occur. Accordingly, customer applications which require a high degree of reliability or safety should
employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies
or other appropriate protective measures) in order to ensure that the failure of an electrical component
does not result in a risk of personal injury or property damage. Although all product-related warnings,
cautions and notes must be observed, the customer should not assume that all safety measures are indicated in such warnings, cautions and notes, or that other safety measures may not be required.
Similar pages