CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Upgrade! NPCAP TM ●Super PSF - Radial Lead Series low ESR, high ripple current capability 5mΩmax. (2 to 4Vdc) ●Longer life (5,000 hours at 105℃) ●ESR after endurance is specified within the initial spec (2 to 4Vdc) ●Rated voltage range : 2 to 16Vdc ●RoHS Compliant ●Halogen Free PSF ●ESR Lower ESR PSE ◆SPECIFICATIONS Items Characteristics Category Temperature Range Rated Voltage Range Capacitance Tolerance Surge Voltage Leakage Current *Note -55 to +105℃ 2 to 16Vdc ±20% (M) Rated voltage(V)×1.15 Shall not exceed values shown in STANDARD RATINGS. Dissipation Factor (tanδ) 0.10 max. Low Temperature Characteristics (Max.Impedance Ratio) Z(-25℃)/Z(+20℃)≦1.15 Z(-55℃)/Z(+20℃)≦1.25 Endurance Bias Humidity Test Surge Voltage Test Failure Rate (at 20℃, 120Hz) (at 105℃) (at 20℃ after 2 minutes) (at 20℃, 120Hz) (at 100kHz) The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 5,000 hours at 105℃. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦The initial specified value ESR 2 to 4Vdc : ≦The initial specified value 16Vdc : ≦150% of the initial specified value Leakage current ≦The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to DC voltage at 60℃, 90 to 95% RH for 1,000 hours. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦The initial specified value ESR 2 to 4Vdc : ≦The initial specified value 16Vdc : ≦150% of the initial specified value Leakage current ≦The initial specified value The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦The initial specified value ESR 2 to 4Vdc : ≦The initial specified value 16Vdc : ≦150% of the initial specified value Leakage current ≦The initial specified value 0.5% per 1,000 hours maximum (Confidence level 60% at 105℃) *Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃. ◆DIMENSIONS [mm] Code : E Coated Case Size code F05 F08 φD 6.3 φd 0.45 0.6 F 2.5 φD' L' L+1.0max. φD' φd F05, F08, H08 F±0.5 ● Terminal 15min. F±0.5 φd φD' (FA5) L' 15min. H08 HB5 8.0 JB5 10.0 0.6 0.5 3.5 φD+0.5max. L+0.3max. L+1.0max. 5.0 L+1.5max. 4min. Coated Case F±0.5 L' FA5, HB5, JB5 FA5 (HB5, JB5) ◆MARKING EX) 2.5V560µF F 6D6 560 2.5V 4min. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. (1/2) CAT. No. E1001M CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Upgrade! NPCAP TM PSF - Radial Lead Series ◆PART NUMBERING SYSTEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 A PS F 2 R 5 E AA 5 6 1 M F 0 8 S Supplement code Size code Capacitance tolerance code Capacitance code (ex. 560µF:561) Lead forming·Taping code Terminal code Voltage code (ex. 2.5V:2R5, 16V:160) Series code Category Please refer to "Product code guide (conductive polymer type)" ◆STANDARD RATINGS WV(Vdc) Cap(µF) 2 1,000 330 470 560 820 1,200 1,600 470 560 100 100 270 270 330 470 470 2.5 4 16 Case size φD×L(mm) 6.3×8 6.3×8 6.3×8 6.3×8 6.3×8 6.3×8 8×8 6.3×8 6.3×8 6.3×5 6.3×10.5 8×8 8×11.5 8×8 8×11.5 10×11.5 ESR Leakage current (mΩ max./20℃, (μAmax/after 2min.) 100k to 300kHz) 500 500 500 500 500 1,200 800 500 500 500 500 864 864 1,050 1,500 1,500 5 5 5 5 5 5 5 5 5 24 25 10 11 13 11 10 Rated ripple current (mArms/105℃, 100kHz) 5,900 5,900 5,900 5,900 5,900 5,900 6,100 5,900 5,900 2,490 2,820 5,000 5,080 4,700 5,400 6,100 Part No. APSF2R0E□□102MF08S APSF2R5E□□331MF08S APSF2R5E□□471MF08S APSF2R5E□□561MF08S APSF2R5E□□821MF08S APSF2R5E□□122MF08S APSF2R5E□□162MH08S APSF4R0E□□471MF08S APSF4R0E□□561MF08S APSF160E□□101MF05S APSF160E□□101MFA5S APSF160E□□271MH08S APSF160E□□271MHB5S APSF160E□□331MH08S APSF160E□□471MHB5S APSF160E□□471MJB5S □□ : Enter the appropriate lead forming or taping code. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. (2/2) CAT. No. E1001M