AVAGO ACPL-M484 Short maximum propagation delay Datasheet

ACPL-M484/P484/W484
Positive Logic High CMR Intelligent Power Module
and Gate Drive Interface Optocoupler
Data Sheet
Description
Features
The ACPL-M484/P484/W484 fast speed optocoupler contains a AlGaAs LED and photo detector with built-in Schmitt
trigger to provide logic-compatible waveforms, eliminating the need for additional wave shaping. The totem
pole output eliminates the need for a pull up resistor and
allows for direct drive Intelligent Power Module or gate
drive. Minimized propagation delay difference between
devices makes these optocouplers excellent solutions for
improving inverter efficiency through reduced switching
dead time.
• Positive output type (totem pole output)
• Truth Table Guaranteed: Vcc from 4.5 V to 30 V
• Performance Specified for Common IPM Applications
Over Industrial Temperature Range.
• Short Maximum Propagation Delays
• Minimized Pulse Width Distortion (PWD)
• Very High Common Mode Rejection (CMR)
• Hysteresis
• Available in SO-5 (ACPL-M484) and Stretched SO-6
package (ACPCL-P484/W484).
Applications
• IPM Interface Isolation
• Package Clearance/Creepage at 8 mm (ACPL-W484)
• Isolated IGBT/MOSFET Gate Drive
• Safety Approval:
• AC and Brushless DC Motor Drives
• Industrial Inverters
– UL Recognized with 5000 Vrms (ACPL-W484) for
1 minute per UL1577.
• General Digital Isolation
– CSA Approved.
Functional Diagram
– IEC/EN/DIN EN 60747-5-5 Approved with VIORM =
567 Vpeak for ACPL-M484 and VIORM = 891 Vpeak for
ACPL-P484 and VIORM = 1140 Vpeak for ACPL-W484,
under option 060.
ACPL-M484
Anode 1
6 VCC
Note: A 0.1 µF bypass
capacitor must be connected between pins
4 Ground Vcc and Ground.
5 VO
Cathode 3
SHIELD
Truth Table
(Positive Logic)
ACPL-P484 & ACPL-W484
Anode 1
6 VCC
N.C. 2
5 VO
Cathode 3
SHIELD
4 Ground
LED
VO
ON
OFF
HIGH
LOW
Truth Table Guaranteed:
Vcc from 4.5 V to 30 V
Specifications
• Wide operating temperature range: -40° C to 105° C
• Maximum propagation delay tPHL / tPLH = 150/120 ns
• Maximum Pulse Width Distortion (PWD) = 90 ns
• Propagation Delay Difference Min/Max = -130/130 ns
• Wide Operating VCC Range: 4.5 to 30 Volts
• 30 kV/µs minimum common mode rejection (CMR) at
VCM = 1000 V
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.
Ordering Information
ACPL-M484/P484/W484 is UL recognized with 3750/3750/5000 Vrms/1 minute rating per UL 1577.
Option
Part number
RoHS Compliant
Package
Surface Mount
ACPL-M484
-000E
SO-5
X
-500E
X
-060E
X
-560E
ACPL-P484
ACPL-W484
-000E
-500E
X
Stretched
SO-6
Tape & Reel
IEC/EN/DIN
EN 60747-5-5
100 per tube
X
X
1500 per reel
X
100 per tube
X
1500 per reel
X
X
-060E
X
-560E
X
Quantity
100 per tube
X
X
1000 per reel
X
100 per tube
X
1000 per reel
To order, choose a part number from the part number column and combine with the desired option from the option
column to form an order entry.
Example 1:
ACPL-P484-560E to order product of Stretched SO-6 Surface Mount package in Tape and Reel packaging with IEC/EN/
DIN EN 60747-5-5 Safety Approval in RoHS compliant.
Example 2:
ACPL-P484-000E to order product of Stretched SO-6 Surface Mount package in Tube packaging and RoHS compliant.
Example 3:
ACPL-M484-000E to order product of SO-5 Surface Mount package in Tube packaging and RoHS compliant.
Option datasheets are available. Contact your Avago sales representative or authorized distributor for information.
2
Package Outline Drawings
ACPL-M484 SO-5 Package, 5 mm Creepage & Clearance
ANODE 1
MXXX
XXX
4.4 ± 0.1
(0.173 ± 0.004)
7.0 ± 0.2
(0.276 ± 0.008)
CATHODE 3
6
VCC
5
VOUT
4
GND
TYPE NUMBER (LAST 3 DIGITS)
DATE CODE
0.4 ± 0.05
(0.016 ± 0.002)
3.6 ± 0.1*
(0.142 ± 0.004)
0.102 ± 0.102
(0.004 ± 0.004)
2.5 ± 0.1
(0.098 ± 0.004)
0.15 ± 0.025
(0.006 ± 0.001)
7° MAX.
0.71 MIN
(0.028)
1.27 BSC
(0.050)
MAX. LEAD COPLANARITY
= 0.102 (0.004)
Dimensions in millimeters (inches).
* Maximum Mold flash on each side is 0.15 mm (0.006).
Note: Foating Lead Protrusion is 0.15 mm (6 mils) max.
Land Pattern Recommendation
4.4
(0.17)
1.3
(0.05)
2.5
(0.10)
2.0
(0.080)
0.64
(0.025)
8.27
(0.325)
Dimension in millimeters (inches)
3
ACPL-P484 Stretched SO-6 Package, 7 mm clearance
4.580 + 0.254
0
1.27 (0.050) BSG
0.381 ±0.127
(0.015 ±0.005)
Land Pattern Recommendation
10.7 (0.421)
(0.180 + 0.010
0.000 )
1.27 (0.050)
0.76 (0.030)
2.16 (0.085)
7.62 (0.300)
1.590 ±0.127
(0.063 ±0.005)
6.81 (0.268)
0.45 (0.018)
45°
3.180 ±0.127
(0.125 ±0.005)
7°
7°
7°
0.20 ±0.10
(0.008 ±0.004)
0.254 ±0.050
(0.010 ±0.002)
7°
5° NOM.
1 ±0.250
(0.040 ±0.010)
Floating Lead Protusions max. 0.25 (0.01)
Dimensions in Millimeters (Inches)
9.7 ±0.250
(0.382 ±0.010)
Lead Coplanarity = 0.1 mm (0.004 Inches)
ACPL-W484 Stretched SO-6 Package, 8 mm clearance
Land Pattern Recommendation (W-type)
4.580 + 0.254
0
1.27 (0.050) BSG
0.381 ±0.127
(0.015 ±0.005)
1
6
2
5
3
4
7.62 (0.300)
6.807 + 0.127
0
(0.180 + 0.010
0.000 )
12.650 (0.498)
0.760 (0.030)
1.905 (0.075)
1.270 (0.050)
(0.268 + 0.005
0.000 )
0.45 (0.018)
7°
45°
1.590 ±0.127
(0.063 ±0.005)
3.180 ±0.127
(0.125 ±0.005)
7°
0.20 ±0.10
(0.008 ±0.004)
0.750 ±0.250
(0.0295 ±0.010)
7°
35° NOM.
11.500 ±0.25
(0.453 ±0.010)
4
7°
0.254 ±0.050
(0.010 ±0.002)
Floating Lead Protusions max. 0.25 (0.01)
Dimensions in Millimeters (Inches)
Lead Coplanarity = 0.1 mm (0.004 Inches)
Recommended Pb-Free IR Profile
Recommended reflow condition as per JEDEC Standard, J-STD-020 (latest revision). Non-Halide Flux should be used.
Regulatory Information
The ACPL-M484/P484/W484 is approved by the following organizations:
IEC/EN/DIN EN 60747-5-5 (Option 060 only)
Approved with Maximum Working Insulation Voltage VIORM = 567 Vpeak for ACPL-M484, VIORM = 891 Vpeak for ACPL-P484
and VIORM = 1140 Vpeak for ACPL-W484
UL
Approval under UL 1577, component recognition program up to VISO = 3750 VRMS File E55361 for ACPL-M484 & ACPLP484;
Approval under UL 1577, component recognition program up to VISO = 5000 VRMS File E55361 for ACPL-W484;
CSA
Approval under CSA Component Acceptance Notice #5, File CA 88324.
Table 1. IEC/EN/DIN EN 60747-5-5 Insulation Characteristics* (ACPL-M484/P484/W484 Option 060)
Description
Symbol
ACPL-M484
ACPL-P484
ACPL-W484
Installation classification per DIN VDE 0110/1.89, Table 1
for rated mains voltage ≤ 150 Vrms
for rated mains voltage ≤ 300 Vrms
for rated mains voltage ≤ 600 Vrms
I – IV
I – III
I – II
I – IV
I – III
I – II
I – IV
I – III
I – II
Climatic Classification
55/105/21
55/105/21
55/105/21
Pollution Degree (DIN VDE 0110/1.89)
2
2
2
Unit
Maximum Working Insulation Voltage
VIORM
567
891
1140
Vpeak
Input to Output Test Voltage, Method b*
VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec,
Partial discharge < 5 pC
VPR
1063
1670
2137
Vpeak
Input to Output Test Voltage, Method a*
VIORM x 1.6 = VPR, Type and Sample Test, tm = 10 sec,
Partial discharge < 5 pC
VPR
907
1426
1824
Vpeak
Highest Allowable Overvoltage
(Transient Overvoltage tini = 60 sec)
VIOTM
6000
6000
8000
Vpeak
Safety-limiting values – maximum values allowed in
the event of a failure.
Case Temperature
Input Current
Output Power
TS
IS, INPUT
PS, OUTPUT
175
230
600
175
230
600
175
230
600
°C
mA
mW
Insulation Resistance at TS, VIO = 500 V
RS
>109
>109
>109
Ω
*
5
Refer to the optocoupler section of the Isolation and Control Components Designer’s Catalog, under Product Safety Regulations section, (IEC/EN/
DIN EN 60747-5-2) for a detailed description of Method a and Method b partial discharge test profiles.
Table 2. Insulation and Safety Related Specifications
Parameter
Symbol
ACPL-M484 ACPL-P484
ACPL-W484 Units
Conditions
Minimum External Air Gap
(External Clearance)
L(101)
5.0
7.0
8.0
mm
Measured from input terminals to
output terminals, shortest distance
through air.
Minimum External Tracking
(External Creepage)
L(102)
5.0
8.0
8.0
mm
Measured from input terminals to
output terminals, shortest distance
path along body.
0.08
0.08
0.08
mm
Through insulation distance conductor
to conductor, usually the straight line
distance thickness between the
emitter and detector.
>175
>175
>175
V
DIN IEC 112/VDE 0303 Part 1
IIIa
IIIa
IIIa
Minimum Internal Plastic Gap
(Internal Clearance)
Tracking Resistance
(Comparative Tracking Index)
CTI
Isolation Group
Material Group (DIN VDE 0110, 1/89,
Table 1)
Table 3. Absolute Maximum Ratings
Parameter
Symbol
Min.
Max.
Units
Note
Storage Temperature
TS
-55
125
°C
Operating Temperature
TA
-40
105
°C
Average Input Current
IF(avg)
10
mA
Peak Transient Input Current
(<1 µs pulse width, 300 pps)
(<200 µs pulse width, < 1% duty cycle)
IF(tran)
1.0
40
A
mA
Reverse Input Voltage
VR
5
V
Average Output Current
IO
50
mA
Supply Voltage
VCC
0
35
Output Voltage
VO
-0.5
35
Total Package Power Dissipation (ACPL-M484)
PT
145
mW
1
Total Package Power Dissipation
PT
210
mW
1
Solder Reflow Temperature Profile
See Reflow Thermal Profile.
Table 4. Recommended Operating Conditions
Parameter
Symbol
Min.
Max.
Units
Note
Power Supply Voltage (1)
VCC
4.5
30
V
2
Forward Input Current (ON)
IF(ON)
4
7
mA
Forward Input Voltage (OFF)
VF(OFF)
–
0.8
V
Operating Temperature
TA
-40
105
°C
Note:
1. Truth Table guaranteed: 4.5 V to 30 V
6
Table 5. Electrical Specifications
Over recommended operating conditions TA = -40° C to 105° C, VCC = +4.5 V to 30 V, IF(ON)= 4 mA to 7 mA, VF(OFF) = 0 V to
0.8 V, unless otherwise specified. All typical values at TA = 25° C.
Parameter
Symbol
Logic Low Output Voltage
VOL
Min.
Typ.
Max.
Units
Test Conditions
Fig.
0.3
V
IOL = 3.5 mA
1, 3
0.5
Logic High Output Voltage
Logic Low Supply Current
Logic High Supply Current
VOH
VCC -0.3
VCC -0.04
Vcc -0.5
VCC -0.07
ICCL
ICCH
Threshold Input Current
Low to High
IFLH
Threshold Input Voltage
High to Low
VFHL
0.8
Logic Low Short Circuit
Output Current
IOSL
125
125
Logic High Short Circuit
Output Current
IOSH
Input Forward Voltage
VF
1.3
IOL = 6.5 mA
V
IOH = -3.5 mA
3.0
mA
VCC = 5.5 V, VF = 0 V, Io = 0 mA
1.7
3.0
mA
VCC = 20 V, VF = 0 V, Io = 0 mA
1.5
3.0
mA
VCC = 5.5 V, IF = 7 mA, Io = 0 mA
1.7
3.0
mA
VCC = 30 V, IF = 7 mA, Io = 0 mA
0.8
2.2
mA
V
IF = 4 mA
200
mA
VO = VCC = 5.5 V, VF = 0 V
200
mA
VO = VCC = 30 V, VF = 0 V
-200
-125
mA
VCC = 5.5 V, IF = 7 mA, VO = GND
-200
-125
mA
VCC = 20 V, IF = 7 mA, VO = GND
1.5
1.7
V
TA = 25° C, IF = 4 mA
1.85
V
IF = 4 mA
V
IR = 10 µA
Input Reverse Breakdown
Voltage
BVR
Input Diode Temperature
Coefficient
∆VF/∆TA
1.7
mV/°C
IF = 4 mA
Input Capacitance
CIN
60
pF
f = 1 MHz, VF = 0 V
7
2, 3, 7
IOH = -6.5 mA
1.5
5
Note
3
3
4
4
Table 6. Switching Specifications
Over recommended operating conditions TA = -40° C to 105° C, VCC = +4.5 V to 30 V, IF(ON) = 4 mA to 7 mA, VF(OFF) = 0 V
to 0.8 V, unless otherwise specified. All typicals at TA = 25° C.
Parameter
Symbol
Min.
Typ.
Max.
Units
Test Conditions
Fig.
Propagation Delay Time
to Logic Low Output Level
tPHL
95
150
ns
CL = 100 pF, IF(ON) = 4 mA → VF = 0 V
5, 6, 8 6
Propagation Delay Time
to Logic High Output Level
tPLH
Pulse Width Distortion
|tPHL - tPLH|
= PWD
Propagation Delay
Difference Between
Any 2 Parts
PDD
Output Rise Time (10-90%)
tr
6
ns
5
Output Fall Time (90-10%)
tf
6
ns
5
Logic High Common Mode
Transient Immunity
|CMH|
30
kV/µs |VCM| = 1000 V, IF = 4.0 mA,
VCC = 5 V, TA = 25° C
9
7
Logic Low Common Mode
Transient Immunity
|CML|
30
kV/µs |VCM| = 1000 V, VF = 0 V,
VCC = 5 V, TA = 25° C
9
7
150
85
120
Loaded as per Fig. 5
ns
120
90
130
-130
130
CL = 100 pF, VF = 0 V → IF(ON) = 4 mA
5, 6, 8 6
Loaded as per Fig. 5
ns
90
-130
Note
CL = 100 pF
9
Loaded as per Fig. 5
ns
CL = 100 pF
10
Loaded as per Fig. 5
Table 7. Package Characteristics
Parameter
Symbol
Min.
Input-Output Momentary
Withstand Voltage*
VISO
3750 (ACPL-M484/P484)
5000 (ACPL-W484)
Input-Output Resistance
RI-O
Input-Output Capacitance
CI-O
*
Typ.
Max.
Units
Test Conditions
Fig.
Note
Vrms
RH < 50%, t = 1 min.
TA = 25° C
5, 8
1012
Ohm
VI-O = 500 Vdc
5
0.6
pF
f = 1 MHz, VI-O = 0 Vdc
5
The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating, refer to the IEC/EN/DIN EN 60747-5-5 Insulation Characteristics Table (if applicable).
UVLO
Figure 10a & b show typical output waveforms during Power-up and Power-down processes.
Notes:
1. Derate total package power dissipation, PT, linearly above 70° C free-air temperature at a rate of 4.5mW/°C(ACPL-P484/W484) and linearly above
85° C free-air temperature at a rate of 0.75mW/°C(ACPL-M484).
2. Detector requires a Vcc of 4.5 V or higher for stable operation as output might be unstable if Vcc is lower than 4.5 V. Be sure to check the power
ON/OFF operation other than the supply current.
3. Duration of output short circuit time should not exceed 500 ms.
4. Input capacitance is measured between pin 1 and pin 3.
5. Device considered a two-terminal device: pins 1, 2 and 3 shorted together and pins 4, 5 and 6 shorted together.
6. The tPLH propagation delay is measured from the 50% point on the leading edge of the input pulse to the 1.3 V point on the leading edge of the
output pulse. The tPHL propagation delay is measured from the 50% point on the trailing edge of the input pulse to the 1.3 V point on the trailing
edge of the output pulse.
7. CMH is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic high state, VO > 2.0 V.
CML is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic low state, VO < 0.8 V. Note:
Equal value split resistors (Rin/2) must be used at both ends of the LED.
8. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 VRMS for one second (leakage detection
current limit, II-O < = 5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/EN/DIN EN
60747-5-5 Insulation Characteristics Table, if applicable.
9. Pulse Width Distortion (PWD) is defined as |tPHL - tPLH | for any given device.
10. The difference of tPLH and tPHL between any two devices under the same test condition.
11. Use of a 0.1 µF bypass capacitor connected between pins Vcc and Ground is recommended.
8
(VCC-VOH) - High Level Output Voltage - V
VOL - LOW LEVEL OUTPUT VOLTAGE - V
0.045
VCC = 4.5 V
VF = 0 V
0.04
0.035
IO = 6.5 mA
0.03
0.025
IO = 3.5 mA
0.02
0.015
0.01
-40
-10
20
50
TA - TEMPERATURE - °C
80
110
Figure 1. Typical Logic Low Output Voltage vs. Temperature
0.06
IO = -3.5 mA
0.04
0.02
-40
-10
4
VCC = 4.5 V
TA = 25° C
3
2
1
0
0.5
1
1.5
2
IF - INPUT CURRENT - mA
2.5
0.01000
0.00100
0.00010
1.2
1.3
1.4
VF - FORWARD VOLTAGE - V
1
6
2
5
4
SHIELD
*0.1 µF BYPASS – SEE NOTE 11
1.6
THE PROBE AND JIG CAPACITANCES ARE
INCLUDED IN C1.
OUTPUT Vo
MONITORING
* NODE
C1 =
15 pF
R1
1000 Ω
560 Ω
IF(ON)
4 mA
7 mA
ALL DIODES ARE EITHER 1N916 OR 1N3064
619 Ω
IF(ON)
D1
D2
R1
1.5
Figure 4. Typical Input Diode Forward Characteristic
5V
Figure 5. Circuit for tPLH, tPHL, tr, tf
110
0.10000
VCC
3
80
1.00000
0.00001
1.1
3
PULSE GEN.
tr = tf = 5 ns
f = 100 kHz
1% DUTY
CYCLE
Vo = 5 V
Zo = 50
INPUT
MONITORING
NODE
20
50
TA - TEMPERATURE - °C
TA = 25° C
10.00000
IF - FORWARD CURRENT - mA
Vo - OUTPUT VOLTAGE - V
IO = -6.5 mA
0.08
100.00000
Figure 3. Typical Output Voltage vs. Forward Input Current
9
IF = 4 mA
Figure 2. Typical Logic High Output Current vs. Temperature
5
0
0.1
5 kΩ
INPUT IF
tPLH
50% IF(ON)
tPHL
0 mA
D3
VOH
D4
OUTPUT V
1.3 V
VOL (0 V)
35
VCC = 4.5 V
TPHL (IF = 4 mA)
100
TPHL (IF = 7 mA)
TPLH (IF = 4 mA)
80
TPLH (IF = 7 mA)
60
-40
-10
20
50
TA - Temperature - °C
Tp - Propagation Delay - ns
25
20
15
10
5
80
0
110
Figure 6. Typical Propagation Delays vs. Temperature
120
IF = 4 mA
TA = 25° C
30
VO - Output Voltage - V
Tp - Propagation Delay - ns
120
0
5
10
15
20
25
VCC - Supply Voltage - V
Figure 7. Typical Logic High Output Voltage vs. Supply Voltage
TA = 25° C
TPHL (IF = 4 mA)
100
TPHL (IF = 7 mA)
TPLH (IF = 4 mA)
80
60
TPLH (IF = 7 mA)
0
5
10
15
20
25
VCC - Supply Voltage - V
30
35
Figure 8. Typical Propagation Delay vs. Supply Voltage
VCC
RIN/2
VFF
CMH
A
B
+
–
1
6
0.1 µF
2
RIN/2
3
5
4
SHIELD
+
VCM
(PEAK)
|VCM|
0V
OUTPUT Vo
MONITORING
NODE
VCM
–
CML
VOH
SWITCH AT A: IF = 4 mA
Vo (MIN.)*
OUTPUT Vo
SWITCH AT B: VF = 0 V
VOL
* SEE NOTE 7
Figure 9. Test Circuit for Common Mode Transient Immunity and Typical Waveforms
10
Vo (MAX.)*
30
35
10 V
Vcc = 2~4 V
Vcc
Vcc = 1.8 V (typ)
Vcc = 2~4 V
Vcc = 1.8 V (typ)
0V
Output
High
Impedance
state
High
Impedance
state
1 ms
i. LED is ON
Discharge delay,
depending on the
power supply slew rate
Figure 10a. Vcc Ramp when LED is ON
10V
Vcc = 2~4 V
Vcc
Vcc = 1.8 V (typ)
Vcc = 2~4 V
Vcc = 1.8 V (typ)
0V
High
Impedance
state
High
Impedance
state
Output
1 ms
Figure 10b. Vcc Ramp when LED is OFF
11
ii. LED is OFF
Discharge delay,
depending on the
power supply slew rate
Thermal Model for ACPL-M484
SO5 Package Optocoupler
Thermal Model for ACPL-P484/W484
SO6 Package Optocoupler
Definitions
Definitions
R11: Junction to Ambient Thermal Resistance of LED due
to heating of LED
R11: Junction to Ambient Thermal Resistance of LED due
to heating of LED
R12: Junction to Ambient Thermal Resistance of LED due
to heating of Detector (Output IC)
R12: Junction to Ambient Thermal Resistance of LED due
to heating of Detector (Output IC)
R21: Junction to Ambient Thermal Resistance of Detector
(Output IC) due to heating of LED.
R21: Junction to Ambient Thermal Resistance of Detector
(Output IC) due to heating of LED.
R22: Junction to Ambient Thermal Resistance of Detector
(Output IC) due to heating of Detector (Output IC).
R22: Junction to Ambient Thermal Resistance of Detector
(Output IC) due to heating of Detector (Output IC).
P1:
Power dissipation of LED (W).
P1:
Power dissipation of LED (W).
P2:
Power dissipation of Detector / Output IC (W).
P2:
Power dissipation of Detector / Output IC (W).
T1:
Junction temperature of LED (˚C).
T1:
Junction temperature of LED (˚C).
T2:
Junction temperature of Detector (˚C).
T2:
Junction temperature of Detector (˚C).
Ta:
Ambient temperature.
Ta:
Ambient temperature.
∆T1: Temperature difference between LED junction and
ambient (˚C).
∆T1: Temperature difference between LED junction and
ambient (˚C).
∆T2: Temperature deference between Detector junction
and ambient.
∆T2: Temperature deference between Detector junction
and ambient.
Ambient Temperature: Junction to Ambient Thermal Resistances were measured approximately 1.25cm above
optocoupler at ~23˚C in still air
Ambient Temperature: Junction to Ambient Thermal Resistances were measured approximately 1.25cm above
optocoupler at ~23˚C in still air
Description
Description
This thermal model assumes that an 5-pin single-channel
plastic package optocoupler is soldered into a 7.62 cm x
7.62 cm printed circuit board (PCB). The temperature at
the LED and Detector junctions of the optocoupler can be
calculated using the equations below.
This thermal model assumes that an 6-pin single-channel
plastic package optocoupler is soldered into a 7.62 cm x
7.62 cm printed circuit board (PCB). The temperature at
the LED and Detector junctions of the optocoupler can be
calculated using the equations below.
T1 = (R11 * P1 + R12 * P2) + Ta -- (1)
T1 = (R11 * P1 + R12 * P2) + Ta -- (1)
T2 = (R21 * P1 + R22 * P2) + Ta -- (2)
T2 = (R21 * P1 + R22 * P2) + Ta -- (2)
Jedec Specifications
R11
R12, R21
R22
Jedec Specifications
R11
R12, R21
R22
low K board
191
77, 91
99
low K board
167
64, 81
89
high K board
126
26, 35
51
high K board
117
31, 39
54
Notes:
1. Maximum junction temperature for above parts: 125 °C.
For product information and a complete list of distributors, please go to our web site:
Notes:
1. Maximum junction temperature for above parts: 125 °C.
www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2013 Avago Technologies. All rights reserved.
AV02-2947EN - September 23, 2013
Similar pages