PAIRUI DNV30-4814 Dc converter Datasheet

DC-DC Converter
DIP-Package
DNV-30 SERIES, 30WATT, 2:1 INPUT RANGE
FEATURES:
3 years warranty
1500Vac isolation voltage
Six-side shielded metal case with low ripple and noise
Operating temperature range -40°C to +85°C
Over voltage, over current, short circuit protection
Remote on/off
Adjustable output voltage
Model
DNV30-1211
DNV30-1212
DNV30-1213
DNV30-1214
DNV30-1215
DNV30-2411
DNV30-2412
DNV30-2413
DNV30-2414
DNV30-2415
DNV30-4811
DNV30-4812
DNV30-4813
DNV30-4814
DNV30-4815
Input voltage
(Vdc)
12(9~18)
24(18~36)
48(36~72)
DNV30-11011
DNV30-11012
DNV30-11013
DNV30-11014
110(66~160)
Output voltage
(Vdc)
Output current
(A)
Efficiency
Typ.
3.3
8
83%
5.1
6
84%
12.1
2.5
85%
15.1
2
85%
24.2
1.25
85%
3.3
8
85%
5.1
6
88%
12.1
2.5
88%
15.1
2
87%
24.2
1.25
87%
3.3
8
85%
5.1
6
88%
12.1
2.5
88%
15.1
2
87%
24.2
1.25
87%
5.1
6
88%
12.1
2.5
88%
15.1
2
87%
24.2
1.25
87%
Notes:
1. Other input and output models may available on request;
2. You may request for the models with heatsink, plus “R” in the suffix, e.g. DNV30-1211R.
www.pairuigroup.com
Page:
1/4
Date: 01/24/2014
DC-DC Converter
DIP-Package
DNV-30 SERIES, 30WATT, 2:1 INPUT RANGE
ELECTRICAL
Input voltage range
Remote control
Input under voltage protection
12V
9-18Vdc
24V
18-36Vdc
48V
36-72Vdc
110V
60-166Vdc
REM left open
Output on
REM connect with -Vin
Output off
When input voltage is lower than the
low terminal input voltage
Auto-recovery
Output voltage accuracy
---
≤1%
Output voltage adjustable
---
±10% max.
Line regulation
Nominal Load, full voltage
±0.2% max.
Load regulation
20% ~ 100% rated load
±0.5% max.
Dynamic response
(transient/recovery time)
Ripple and noise
Isolation voltage
(<2mA/min)
5%-50%-75% load capability
20MHz BM, full load
∆Vo/∆t: ±5.0%/200μs
1% Vout max.
Input to output
1500Vac
Input to case
1500Vac
Output to case
500Vac
Isolation resistance
500Vdc
100MΩ
Temperature coefficient
---
Operating temperature range
Auxiliary heat sink
Storage temperature range
---
-45°C to +120°C
Over current protection
---
Auto-recovery
Short circuit protection
---
Continuous auto-recovery
Over voltage protection
---
Auto-recovery
Cooling method
30W need external heatsink
Relative humidity
---
10%-90% max.
Weight
---
60g
MTBF
Bellcore TR-332, 25°C
±0.02%/°C max.
-40°C to +85°C
Cooling by air convection
2x105Hrs
Notes: Unless otherwise specified, all the parameters of the test conditions are as follows: ambient temperature
25 , the nominal input voltage, pure resistive nominal load.
℃
www.pairuigroup.com
Page:
2/4
Date: 01/24/2014
DC-DC Converter
DIP-Package
DNV-30 SERIES, 30WATT, 2:1 INPUT RANGE
MECHANICAL
WITHOUT HEATSINK
WITH HEATSINK
50.8
(2.0)
4.6
(0.18)
5.08
(0.2)
1
BOTTOM VIEW
5
10.16
(0.4)
3
6
1
10.16
(0.4)
2
5.6
(0.22)
5.08
(0.2)
6
10.16
(0.4)
50.8
(2.0)
4.6
(0.18)
10.16
(0.4)
2
25.4
(1.0)
5.6
(0.22)
4
5
BOTTOM VIEW
10.16
(0.4)
10.16
(0.4)
3
25.4
(1.0)
4
10.0
(0.39)
12.4 11.5
(0.49) (0.45)
SIDE VIEW
5.08
(0.2)
12.4 11.5
(0.49) (0.45)
SIDE VIEW
1.00(0.039)
5.08
(0.20)
PCB LAYOUT
1.0(0.039)
CONNECTION
PIN #
SINGLE
1
+Vin
2
-Vin
3
REM
4
TRIM
5
GND
6
+Vo
Note:
* Unit is mm(inch).
TEMPERATURE PROFILE
www.pairuigroup.com
Page:
3/4
Date: 01/24/2014
DC-DC Converter
DIP-Package
DNV-30 SERIES, 30WATT, 2:1 INPUT RANGE
CAPACITIVE LOADS SELECTION
Vout:3.3V 5V
Vout:12V 5V
Vout:24V
Recommended
MAX.
Recommended
MAX.
Recommended
MAX.
value
value
value
value
value
value
10000μF
15000μF
3000μF
6000μF
2000μF
3000μF
NOTES
RECOMMENDED TEST AND APPLICATION CIRCUIT
1. TVS&FUSE be helpful with over voltage protection and inrush limiting. Recommended FUSE better be 1.5~2times of
the rated current .
2. The input filter capacitor C6 could select the aluminum electrolytic capacitors or tantalum capacitors, and the
withstand voltage should be greater than the highest input voltage. Recommended capacitor should be between
22μF~100μF.
3. C1,C2 for the input filter capacitor,0.1~1μF high-frequency ceramics capacitor or chip capacitor are recommended.
The withstand voltage of output filter C5, C7 should be greater than the highest output voltage. Recommended
capacitor of C7 better within 100μF and C5 connected with the chip to reduce the input voltage peak, recommended
0.1~1μF high-frequency ceramics capacitor or chip capacitor.
www.pairuigroup.com
Page:
4/4
Date: 01/24/2014
Similar pages