TT CGH-31002205FLF Precision high-voltage thick film resistor Datasheet

Resistors
Precision High-Voltage
Thick
FilmHigh-Voltage
Resistors
Precision
Thick Film Resistors
CGH Series
1/4 watt to 5 watt
TCR of ±50 or ±100 ppm/°C
100K
ohm to 2000 megohm range
CGH
Series
±0.5%,
±2% or ±5% tolerance
• 1/4 watt to±1%,
5 watt
High thermal
conductivity substrate
• TCR of ±50 or ±100 ppm/°C
High thermal
conductivity substrate
• 100K ohm to 2000 megohm range
• ±0.5%, ±1%, ±2% or ±5% tolerance
All Pb-free parts comply with EU Directive 2011/65/EU (RoHS2)
Electrical Data
Power Rating
at 70°C (watts)¹
Voltage Rating
(volts)²
Resistance
Range (ohms)³
CGH - 1/4
1/4
750
100K - 100M
CGH - 1/2
1/2
1,500
100K - 500M
CGH - 1
1
3,000
50K - 750M
CGH - 2
2
5,000
100K - 1500M
CGH - 3
3
10,000
200K - 2000M
CGH - 5
5
20,000
300K - 2000M
IRC Type
Tolerance
(±%)4
Maximum TCR
(±ppm/°C)4
VCR (ppm/V)5
.5, 1, 2, 5
50, 100
0 - -5
Notes:
1. For power rating above 70°C, see derating curve.
2. Voltage rating shown is the rated DC continuous working voltage or the sine-wave RMS absolute maximum voltage at commercial line frequency. For DC applications the absolute maximum permissible voltage is 1.5 times the value shown for low repetition short-time-overload or
pulse conditions of 10 seconds or less duration.
3. Contact factory for higher resistance values.
4. For CGH-1 and 2 above 500 meg and CGH-3 and 5 above 1000M only 2 and 5% tolerance and 100 ppm/°C TCR available.
5. Typical voltage coefficient of resistance is -1 to -2 ppm/V measured at fulll rated voltage and 10% rated voltage.
Power Derating Curve
Temperature Rise Chart
100
100
70
60
50
40
30
20
CGH 2-3
80
CGH 1/2
70
CGH 5
60
CGH 1
50
40
30
20
10
0
CGH 1/4
90
80
% of Rated Power
% of Rated Power
90
10
80
100
120
140
160
180
0
Ambient Temperature (°C)
General Note
IRC reserves Note
the right to make changes in product specification without notice or liability.
General
All information is subject to IRC’s own data and is considered accurate at time of going to print.
TT Electronics reserves the right to make changes in product specification without notice or liability.
Wire
and Film
Technologies
Division
Street • Corpus
Christi
USA to print.
All
information
is subject
to TT Electronics’
own• 4222
dataSouth
and Staples
is considered
accurate
at Texas
time 78411
of going
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
0
10
20
30
40
50
60
70
80
90
Temperature Rise (°C)
BI Technologies IRC Welwyn
A subsidiary of
TT electronics plc
CGH Series Issue June 2009 Sheet 1 of 3
http://www.ttelectronics.com/resistors
© TT Electronics plc
12.16
Precision High-Voltage
Thick Film Resistors
CGH Series
Precision High-Voltage
Thick Film Resistors
Environmental Data
Maximum ∆R
(±3σ)
Typical² ∆R
Temperature Shock
±0.25%
±0.10%
Short-Time Overload (1.5 times rated V for 10 sec)
±0.20%
±0.10%
Solder Effect
±0.15%
±0.05%
Terminal Strength
±0.20%
±0.05%
Moisture Resistance (no load or polar)
±0.50%
±0.20%
Load Life (1000 hours at 70°C)
±1.00%
±0.25%
Shelf Life (1 year at 25°C)
±0.10%
±0.03%
High-Temperature Exposure (150°C for 2000 hours)
±0.75%
±0.30%
±1.0%
±0.40%
Test Condition¹
(175°C for 2000 hours)
Dielectric Breakdown³ (1/4 and 1/2 watt size)
2000 VDC, 1500 VAC
(1 watt through 5 watt size)
3500 VDC, 2500 VAC
Dielectric Strength4
Insulation Resistance at 500 VDC
±0.15%
±0.05%
109 ohms typ.
1011 ohms typ.
Notes:
1. Test method per MIL-STD-202 unless otherwise indicated.
2. Typical defined as that percent change which will include a minimum of 50% of the measured changes in resistance from a variety of lots
representing various unit sizes and ranges.
3. Values shown are the maximum safe dielectric voltage applied from a V block or foil wrapping which extends the complete body length of the
resistor under test.
4. Percent change after the maximum safe dielectric voltage is applied for 1 minute.
Wire and Film Technologies Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
General Note
TT Electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT Electronics’ own data and is considered accurate at time of going to print.
CGH Series Issue June 2009 Sheet 2 of 3
BI Technologies IRC Welwyn
http://www.ttelectronics.com/resistors
© TT Electronics plc
12.16
Precision High-Voltage
Thick Film Resistors
CGH Series
Precision High-Voltage
Thick Film Resistors
Precision High-Voltage
Thick Film Resistors
Physical Data
Physical Data
1.50 ± 0.125
(38.1 ± 3.2)
BL
1.50 ± 0.125
(38.1 ± 3.2)
BL
0.032 (0.81) DIA.*
BD
* CGH 1/4 leads are
0.025 (0.64) in diameter”
CL
Dimensions (Inches and (mm))
BD
IRC Type
Body Length - BL
0.032 (0.81) DIA.
CL
Body Diameter - BD
Clean Lead to Clean Lead - CL
CGH - 1/4
(Inches
(mm))
0.275 ± 0.031 (6.98 Dimensions
± 0.79)
0.088 ± and
0.010
(2.22 ± 0.25)
CGH -IRC
1/2 Type
Length
- BL
0.400Body
± 0.031
(10.16
± 0.79)
Body
Diameter
0.138
± 0.016
(3.51-±BD
0.41)
Clean Lead
to Clean
0.525
(13.34)Lead - CL
CGH
CGH -- 1/4
1
0.275±±0.062
0.031(17.53
(6.98 ±±0.79)
0.690
1.57)
0.088
0.297 ±
± 0.010
0.031 (2.22
(7.54 ±
± 0.25)
0.79)
0.400
0.900 (10.16)
(22.86)
CGH
CGH -- 1/2
2
0.400
1.062 ±
± 0.031
0.062 (10.16
(26.97 ±
± 0.79)
1.57)
0.138
0.297 ±
± 0.016
0.031 (3.51
(7.54 ±
± 0.41)
0.79)
0.525
1.250 (13.34)
(31.75)
CGH
CGH -- 1
3
0.690
2.062 ±
± 0.062
0.062 (17.53
(52.37 ±
± 1.57)
1.57)
0.297
0.297 ±
± 0.031
0.031 (7.54
(7.54 ±
± 0.79)
0.79)
0.900
2.250 (22.86)
(57.15)
CGH
CGH -- 2
5
1.062
3.062 ±
± 0.062
0.062 (26.97
(77.77 ±
± 1.57)
1.57)
0.297
0.297 ±
± 0.031
0.031 (7.54
(7.54 ±
± 0.79)
0.79)
1.250
3.250 (31.75)
(82.55)
CGH - 3
2.062 ± 0.062 (52.37 ± 1.57)
0.297 ± 0.031 (7.54 ± 0.79)
2.250 (57.15)
CGH - 5
Ordering
Data 3.062 ± 0.062 (77.77 ± 1.57)
0.297 ± 0.031 (7.54 ± 0.79)
3.250 (82.55)
Sample Part No.
0.400 (10.16)
CGH 3 - 100 - 2205 - F - LF
Ordering
Data
IRC Type
CGH 1/4, CGH 1/2, CGH 1, CGH 2, CGH 3, CGH 5
Temperature Coefficient
Sample
Part±50
No.ppm/°C)
(±100 ppm/°C,
CGH 3 - 100 - 2205 - F - LF
Resistance
IRC Type
CGH 1/4, CGH 1/2, CGH 1, CGH 2, CGH 3, CGH 5
Tolerance
D = ±0.5%
Temperature
Coefficient
F
= ±1%
(±100
ppm/°C, ±50 ppm/°C)
G = ±2%
JResistance
= ±5%
RoHS Indicator
Tolerance
LF indicates RoHS compliance
D = ±0.5%
Omit this code for SnPb finish
F = ±1%
G = ±2%
J = ±5%
RoHS Indicator
LF indicates RoHS compliance
Omit this code for SnPb finish
Wire and Film Technologies Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
Wire and Film Technologies Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA
General361Note
Telephone:
992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
TT Electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT Electronics’ own data and is considered accurate at time of going to print.
CGH Series Issue June 2009 Sheet 3 of 3
CGH Series
Issue June Welwyn
2009 Sheet 3 of 3
BI Technologies
IRC
http://www.ttelectronics.com/resistors
© TT Electronics plc
12.16
Similar pages