MP2371 1.8A, 24V, 700KHz Step-Down Converter The Future of Analog IC Technology DESCRIPTION FEATURES The MP2371 is a monolithic step-down switch mode converter with a built-in internal power MOSFET. It achieves 1.8A continuous output current over a wide input supply range with excellent load and line regulation. Current mode operation provides fast transient response and eases loop stabilization. Fault condition protection includes cycle-by-cycle current limiting and thermal shutdown. • • • • • • • • • • • The MP2371 requires a minimum number of readily available standard external components. The MP2371 is available in a 2mm x 2mm QFN8 package. 2.5A Peak Output Current 1.8A Continuous Output Current 0.3Ω Internal Power MOSFET Switch Stable with Low ESR Output Ceramic Capacitors 0.1µA Shutdown Mode Fixed 700KHz Frequency Thermal Shutdown Cycle-by-Cycle Over Current Protection Wide 4.5V to 24V Operating Input Range Output Adjustable from 0.81V to 15V Available in 2x2 QFN8 Package APPLICATIONS • • • • • Broadband Communications Equipment Digital Entertainment Systems Distributed Power Systems Battery Charger Pre-Regulator for Linear Regulators “MPS” and “The Future of Analog IC Technology” are Registered Trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION VIN 3 IN BST 7 GND D3 SW EN 4 EN GND FB 2 5 VOUT GND 6 VIN IOUT_MAX=1.8 MP2371 Rev. 1.0 5/26/2008 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2008 MPS. All Rights Reserved. 1 MP2371 – 1.8A, 24V, 700KHz STEP-DOWN CONVERTER ABSOLUTE MAXIMUM RATINGS (1) PACKAGE REFERENCE Supply Voltage VIN ....................................... 26V VSW....................................... –0.3V to VIN + 0.3V VBS ....................................................... VSW + 6V All Other Pins................................. –0.3V to +6V Junction Temperature...............................150°C Lead Temperature ....................................260°C Storage Temperature ..............–65°C to +150°C TOP VIEW NC 1 8 NC SW 2 7 BST IN 3 6 GND EN 4 5 FB Recommended Operating Conditions Supply Voltage VIN ........................... 4.5V to 24V Output Voltage VOUT ...................... 0.81V to 15V Operating Temperature .............–40°C to +85°C QFN8 (2mm x 2mm) Thermal Resistance (3) θJA θJC 2x2 QFN8 ............................... 80 ...... 16... °C/W Part Number* Package Temperature MP2371DG 2x2 QFN8 –40°C to +85°C * (2) For Tape & Reel, add suffix –Z (eg. MP2371DG–Z) For RoHS compliant packaging, add suffix –LF (eg. MP2371DG–LF–Z) Notes: 1) Exceeding these ratings may damage the device. 2) The device is not guaranteed to function outside of its operating conditions. 3) Measured on approximately 1” square of 1 oz copper. ELECTRICAL CHARACTERISTICS VIN = 12V, TA = +25°C, unless otherwise noted. Parameters Symbol Condition Feedback Voltage Feedback Current (4) Switch On-Resistance Switch Leakage Current Limit (4) Oscillator Frequency Fold-back Frequency Maximum Duty Cycle Minimum On-Time (4) Under-Voltage Lockout Threshold Rising Under-Voltage Lockout Threshold Hysteresis EN Input Low Voltage EN Input High Voltage EN Input Current Supply Current (Shutdown) Supply Current (Quiescent) Thermal Shutdown (4) VFB 4.5V ≤ VIN ≤ 24V IFB VFB = 0.8V Min Typ Max Units 0.790 0.810 0.830 V RDS(ON) fSW VEN = 0V, VSW = 0V Duty Cycle = 40% VFB = 0.6V VFB = 0V VFB = 0.6V 2.0 tON 2.5 10 nA 0.3 0 2.5 700 230 87 100 2.8 150 Ω µA A KHz KHz % ns V mV V V 10 3.1 0.4 1.5 VEN = 2V VEN = 0V VEN = 0V VEN = 2V, VFB = 1V 2.1 0.01 0.1 0.8 150 µA 1.0 1.0 µA mA °C Note: 4) Guaranteed by design. MP2371 Rev. 1.0 5/26/2008 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2008 MPS. All Rights Reserved. 2 MP2371 – 1.8A, 24V, 700KHz STEP-DOWN CONVERTER PIN FUNCTIONS Pin # Name Description 1, 8 2 NC SW 3 IN 4 EN 5 FB 6 GND 7 BST MP2371 Rev. 1.0 5/26/2008 No Connect. Switch Output. Supply Voltage. The MP2371 operates from a +4.5V to +24V unregulated input. C1 is needed to prevent large voltage spikes from appearing at the input. On/Off Control Input. Pull above 1.5V to turn the device on. Feedback. An external resistor divider from the output to GND, tapped to the FB pin sets the output voltage. To prevent current limit run away during a short circuit fault condition the frequency foldback comparator lowers the oscillator frequency when the FB voltage is below 250mV. Ground. This pin is the voltage reference for the regulated output voltage. For this reason care must be taken in its layout. This node should be placed outside of the D1 to C1 ground path to prevent switching current spikes from inducing voltage noise into the part. Bootstrap. This capacitor is needed to drive the power switch’s gate above the supply voltage. It is connected between SW and BST pins to form a floating supply across the power switch driver. www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2008 MPS. All Rights Reserved. 3 MP2371 – 1.8A, 24V, 700KHz STEP-DOWN CONVERTER TYPICAL PERFORMANCE CHARACTERISTICS VIN = 12V, VOUT = 1.8V, L=6.8µH, ILOAD=0.5A – 1.8A, TA = +20°C, unless otherwise noted. 900 3.0 880 2.5 860 840 2.0 820 800 1.5 780 1.0 760 740 0.5 720 700 5 10 15 20 0 5 10 15 20 25 0 0 20 40 60 80 100 40 35 30 VOUT_MAX DMAX Limit VIN=20V 25 20 VIN=12V Minimum On Time Limit 15 10 VFB_MIN 5 0 0 MP2371 Rev. 1.0 5/26/2008 0.5 1.0 1.5 2.0 0 5 10 15 20 25 0 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2008 MPS. All Rights Reserved. 1 4 MP2371 – 1.8A, 24V, 700KHz STEP-DOWN CONVERTER TYPICAL PERFORMANCE CHARACTERISTICS (continued) VIN = 12V, VOUT = 1.8V, L=6.8µH, ILOAD=0.5A – 1.8A, TA = +20°C, unless otherwise noted. MP2371 Rev. 1.0 5/26/2008 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2008 MPS. All Rights Reserved. 5 MP2371 – 1.8A, 24V, 700KHz STEP-DOWN CONVERTER OPERATION The MP2371 is a current mode buck regulator. That is, the EA output voltage is proportional to the peak inductor current. At the beginning of a cycle, M1 is off. The EA output voltage is higher than the current sense amplifier output, and the current comparator’s output is low. The rising edge of the 700KHz CLK signal sets the RS Flip-Flop. Its output turns on M1 thus connecting the SW pin and inductor to the input supply. The increasing inductor current is sensed and amplified by the Current Sense Amplifier. Ramp compensation is summed to Current Sense Amplifier output and compared to the Error Amplifier output by the PWM Comparator. When the sum of the Current Sense Amplifier output and the Slope Compensation signal exceeds the EA output voltage, the RS FlipFlop is reset and the M1 is turned off. The external Schottky rectifier diode (D1) conducts the inductor current. If the sum of the Current Sense Amplifier output and the Slope Compensation signal does not exceed the EA output for a whole cycle, then the falling edge of the CLK resets the Flip-Flop. The output of the Error Amplifier integrates the voltage difference between the feedback and the 0.81V bandgap reference. The polarity is such that a FB pin voltage lower than 0.8V increases the EA output voltage. Since the EA output voltage is proportional to the peak inductor current, an increase in its voltage also increases current delivered to the output. IN x20 CURRENT SENSE AMPLIFIER + -- D REGULATOR BST EN REGULATOR OSCILLATOR 700KHz S + -1pF REFERENCE FB Q DRIVER M1 R CURRENT LIMIT COMPARATOR R SW 27pF +EA -- ERROR AMPLIFIER + -- PWM COMPARATOR GND Figure 1—Functional Block Diagram MP2371 Rev. 1.0 5/26/2008 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2008 MPS. All Rights Reserved. 6 MP2371 – 1.8A, 24V, 700KHz STEP-DOWN CONVERTER APPLICATION INFORMATION Setting Output Voltage The external resistor divider is used to set the output voltage (see the schematic on front page). The feedback resistor R1 also sets the feedback loop bandwidth with the internal compensation capacitor (see Figure 1). R2 can be determined by: R2 = R1 VOUT −1 0.81V Table 1—Resistor Selection for Common Output Voltages VOUT (V) R1 (kΩ) R2 (kΩ) 1.8 2.5 3.3 5 80.6 (1%) 49.9 (1%) 49.9 (1%) 49.9 (1%) 64.9 (1%) 23.7 (1%) 16.2 (1%) 9.53 (1%) Selecting the Inductor A 1µH to 10µH inductor with a DC current rating of at least 25% percent higher than the maximum load current is recommended for most applications. For highest efficiency, the inductor’s DC resistance should be less than 200mΩ. For most designs, the required inductance value can be derived from the following equation. L1 = VOUT × (VIN − VOUT ) VIN × ∆IL × fOSC Selecting the Input Capacitor The input capacitor reduces the surge current drawn from the input and the switching noise from the device. The input capacitor impedance at the switching frequency should be less than the input source impedance to prevent high frequency switching current from passing through the input. Ceramic capacitors with X5R or X7R dielectrics are highly recommended because of their low ESR and small temperature coefficients. For most applications, a 10µF capacitor is sufficient. Selecting the Output Capacitor The output capacitor keeps output voltage ripple small and ensures loop stability. The output capacitor impedance should be low at the switching frequency. Ceramic capacitors with X5R or X7R dielectrics are recommended for their low ESR characteristics. For most applications, a 22µF ceramic capacitor will be sufficient. PCB Layout Guide PCB layout is very important to achieve stable operation. Please follow these guidelines and take Figure2 for references. 1) Keep the path of switching current short and minimize the loop area formed by Input cap, high-side MOSFET and schottky diode. 2) Keep the connection of schottky diode between SW pin and input power ground as short and wide as possible. 3) Ensure all feedback connections are short and direct. Place the feedback resistors and compensation components as close to the chip as possible. 4) Route SW away from sensitive analog areas such as FB. 5) Connect IN, SW, and especially GND respectively to a large copper area to cool the chip to improve thermal performance and long-term reliability. For single layer, do not solder exposed pad of the IC. Where ∆IL is the inductor ripple current. Choose an inductor with a rating current of approximately 30% higher than the maximum load current if the maximum load current is ≥1.8A. The maximum inductor peak current is calculated from: IL(MAX ) = ILOAD + ∆I L 2 Under light load conditions below 100mA, a larger inductance is recommended for improved efficiency. See Table 2 for suggested inductors. MP2371 Rev. 1.0 5/26/2008 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2008 MPS. All Rights Reserved. 7 MP2371 – 1.8A, 24V, 700KHz STEP-DOWN CONVERTER External Bootstrap Diode An external bootstrap diode may enhance the efficiency of the regulator, the applicable conditions of external BST diode are: z VOUT=5V or 3.3V; and z Duty cycle is high: D= VOUT >65% VIN In these cases, an external BST diode is recommended from the output of the voltage regulator to BST pin, as shown in Fig.3 External BST Diode IN4148 BST CBST MP2371 Top Layer SW L 5V or 3.3V COUT Figure 3—Add Optional External Bootstrap Diode to Enhance Efficiency The recommended external BST diode is IN4148, and the BST cap is 0.1~1µF. Bottom Layer Figure2―PCB Layout Table 2—Suggested Surface Mount Inductors Manufacturer Part Number Inductance(µH) Max DCR(Ω) Current Rating (A) Dimensions L x W x H (mm3) Wurth Electronics Toko Coiltronics 7447785004 A916CY-4R7M DR73-4R7 4.7 4.7 4.7 0.060 0.026 0.03 2.5 2.5 3 5.9 x 6.2 x 3.3 6.2 x 6.3 x 3.5 6.0 x 7.6 x 3.5 MP2371 Rev. 1.0 5/26/2008 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2008 MPS. All Rights Reserved. 8 MP2371 – 1.8A, 24V, 700KHz STEP-DOWN CONVERTER TYPICAL APPLICATION CIRCUIT VIN 3 IN BST 7 GND D3 SW EN 4 EN GND FB 2 5 VOUT GND 6 Figure 4—700KHz, 3.3V Output Step-Down Converter MP2371 Rev. 1.0 5/26/2008 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2008 MPS. All Rights Reserved. 9 MP2371 – 1.8A, 24V, 700KHz STEP-DOWN CONVERTER PACKAGE INFORMATION 2mm x 2mm QFN8 PIN 1 ID MARKING 1.90 2.10 0.25 0.45 0.18 0.30 1.90 2.10 PIN 1 ID INDEX AREA PIN 1 ID SEE DETAIL A 0.45 0.65 8 1 1.05 1.25 0.50 BSC 5 TOP VIEW 4 BOTTOM VIEW 0.80 1.00 PIN 1 ID OPTION A R0.20 TYP. PIN 1 ID OPTION B R0.20 TYP. 0.20 REF 0.00 0.05 SIDE VIEW DETAIL A NOTE: 1.90 0.70 0.60 1) ALL DIMENSIONS ARE IN MILLIMETERS. 2) EXPOSED PADDLE SIZE DOES NOT INCLUDE MOLD FLASH. 3) LEAD COPLANARITY SHALL BE 0.10 MILLIMETER MAX. 4) DRAWING CONFORMS TO JEDEC MO-229, VARIATION VCCD-3. 5) DRAWING IS NOT TO SCALE. 0.25 1.20 0.50 RECOMMENDED LAND PATTERN NOTICE: The information in this document is subject to change without notice. Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications. MP2371 Rev. 1.0 5/26/2008 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2008 MPS. All Rights Reserved. 10