Mitsubishi Electric Corp. Datasheet MITSUBISHI OPTICAL DEVICES MF-10KSXA-007ZA 10Gbps 1310nm XFP Optical Transceiver XFP Multirate Optical Transceiver MF-10KSXA-007ZA Features: • • • • • • • Protocol Independent 10Gbps transceiver Hot pluggable Management interface compliant with I2C™ rev. 2 and XFP MSA Multi rate from 9.95Gbps to 11.0957Gbps (FEC) XFI compatible electrical interface thru 30pin connector Low power dissipation: < 2.5W Low cost Changes for the Better UQ9-07-005(XF-10K) (1/15) Mitsubishi Electric Corp. Datasheet MITSUBISHI OPTICAL DEVICES MF-10KSXA-007ZA 10Gbps 1310nm XFP Optical Transceiver 1. Description This XFP optical transceiver is designed to provide high optical performance for SDH I-64.1 / SONET SR-1 (2km) and IEEE 802.3ae LR (10km). Transmitter side uses 1310nm DFB with specified driving circuit and signal conditioning circuit. Receiver side uses PD preamp-module and integrated circuits for re-shaping, re-timing and re-generating input optical signal. Input and output signals handle NRZ format. Digital diagnostic functions are also available via 2-wire interface according to the XFP MSA specification. 2. Block Diagram 2.1 Total Block Diagram System side XFP Transceiver 2 ASIC/SerDes TD+/- Signal Conditioner Driver DFBLD Opt. Out APC 2 RD+/- Signal Conditioner Post Amp ROSA PD/APD Opt. In Monitor 2 SCL/SDA 2 Micro Controller Control Monitor/Alarm Reference Clock RefCLK+/- Control Signals Control Signals Fig. 2.1 Changes for the Better Block Diagram UQ9-07-005(XF-10K) (2/15) Mitsubishi Electric Corp. Datasheet MITSUBISHI OPTICAL DEVICES MF-10KSXA-007ZA 10Gbps 1310nm XFP Optical Transceiver 3. Absolute Maximum Ratings Stress below listed absolute maximum rating may cause permanent damage to the module. This is a stress only and functional operation of the module at these or any other conditions in excess of those given in the operational sections of this data sheet. Exposure to Absolute Maximum Rating for extended periods may affect module reliability. Table 3.1 Parameter Absolute Maximum Ratings (MF-10KSXA-007ZA) Symbol Min Max Supply Voltage VDD3 0 +3.6 Storage temperature Tstg -40 +85 Operating temperature (Case) Tcase -5 +70 Relative humidity (Non condensation) 5 90 Changes for the Better Unit V degC degC % UQ9-07-005(XF-10K) (3/15) Mitsubishi Electric Corp. Datasheet MITSUBISHI OPTICAL DEVICES MF-10KSXA-007ZA 10Gbps 1310nm XFP Optical Transceiver 4. Pin Descriptions Table 4.1 shows the Pin descriptions of XFP connector and Fig.4.2 shows the Diagram of Host Board Connector Pin Numbers and Names. Table 4.1 Pin Descriptions of XFP Connector Pin Logic Symbol Name/Description 1 GND Module Ground 2 VEE5 Optional –5.2V Power Supply 3 LVTTL-I Mod_Desel Prevent module from communicating cia I2C 4 LVTTL-O /Interrupt Indicates presence of an important conditions 5 LVTTL-I Tx_Dis Laser source turned off 6 VDD5 +5V Power Supply 7 GND Module Ground 8 VDD3 +3.3V Power Supply 9 VDD3 +3.3V Power Supply 10 LVTTL-I/O SCL I2C Serial Interface Clock 11 LVTTL-I/O SDA I2C Serial Interface Data Line 12 LVTTL-O Mod_Abs Module-Absent indicator 13 LVTTL-O Mod_Nr Module-Not-Ready indicator 14 LVTTL-O Rx_Los Receive-Loss-Of-Signal Indicator 15 GND Module Ground 16 GND Module Ground 17 CML-O RDN Inverted Receiver Data Output 18 CML-O RDP Receiver Data Output 19 GND Module Ground 20 VDD2 +1.8V Power Supply 21 LVTTL-I PDown/RST Power down / Reset command 22 VDD2 +1.8V Power Supply 23 GND Module GND 24 PECL-I CRefP Reference Clock Input 25 PECL-I CREfN Inverted Reference Clock Input 26 GND Module GND 27 GND Module GND 28 CML-I TDN Inverted Transmitter Data Input 29 CML-I TDP Transmitter Data Input 30 GND Module GND Note; 1. Module ground pins GND are isolated from the module case and chassis ground within the module. 2. Shall be pulled up with 4.7k-10kohms to a voltage between 3.15V and 3.45V on the board Changes for the Better Note 1 2 1 2 2 2 2 2 1 1 1 1 1 1 1 UQ9-07-005(XF-10K) (4/15) Mitsubishi Electric Corp. Datasheet Fig. 4.2 Fig. 4.3 MITSUBISHI OPTICAL DEVICES MF-10KSXA-007ZA 10Gbps 1310nm XFP Optical Transceiver Diagram of Host Board Connector Block Pin Numbers and Names Diagram of Transceiver card edge connector Numbers and Names (See Fig. 8.1) Changes for the Better UQ9-07-005(XF-10K) (5/15) MITSUBISHI OPTICAL DEVICES Mitsubishi Electric Corp. Datasheet MF-10KSXA-007ZA 10Gbps 1310nm XFP Optical Transceiver 5. Electrical Characteristics All parameters are specified over the operating case temperature. 5.1 Power Supply Table 5.1.1 Power Supply Parameters Min. Tc : -5 to +70degC Typ. Max. Unit SupplyVoltage VDD3 +3.13 +3.3 +3.47 V SupplyCurrent Power Consumption Idd3 W - - 700 2.5 mA W 5.2 Host Filtering and Supply Voltage Measurement Points The example host board power supply filtering and Supply voltage measurement points are shown in Fig 5.2.1. Host board power supply must meet XFP MSA specification. 4.7µH 0.1uF Host +3.3V 0.1uF Host +1.8V 0.1uF Host –5.2V 0.1uF 22uF VDD5 0.1uF 4.7µH 22uF VDD3 0.1uF 4.7µH 22uF VDD2 XFP Module 0.1uF 4.7µH 22uF Connector Host +5V VEE5 0.1uF Measurement points Fig. 5.2.1 Example of Host Board Supply Filtering Network and Supply Voltage measurement points Changes for the Better UQ9-07-005(XF-10K) (6/15) Mitsubishi Electric Corp. Datasheet MITSUBISHI OPTICAL DEVICES MF-10KSXA-007ZA 10Gbps 1310nm XFP Optical Transceiver 5.3 High Speed Electrical Interface XFP Module high-speed electrical interface specification is shown in table 5.3.1 and the High Speed Electrical Interface definition point is shown in Fig. 5.3.1. Table 5.3.1 Parameter Transmitter Input Input Differential Impedance Termination Mismatch Source to Sink DC Potential Difference Input AC Common mode Voltage Differential Input Return Loss Common Mode Input Return Loss Differential to Common Mode Conversion Total Non-DDJ Jitter Total Jitter Sinusoidal Jitter Tolerance High Speed Electrical Interface Min Typ Max Unit Zd ∆ZM Vcm 80 100 120 5 3.6 25 SDD11 SCC11 8 3 ohm % V mV(RMS) dB dB Up to 8GHz 0.1-15GHz SCD11 10 dB 0.1-15GHz TJ SJ X1 Y1 Y2 Eye Mask Receiver Output Reference Differential Output Impedance Termination Mismatch DC Common Mode Potential Output AC Common Mode Voltage Output Rise and Fall time Differential Output Return Loss Common Mode Output Return Loss Deterministic Jitter Total Jitter Eye Mask Reference Clock Clock Differential Input Impedance Differential Input Clock Amplitude Reference Clock Duty Cycle Reference Clock Rise/Fall time Reference Clock Frequency RMS Jitter Random Jitter Reference Clock Frequency Tolerance 1. 2. 3. 4. Tc : -5 to +70degC Note Symbol 0 0.41 0.61 See 2 0.305 60 410 Zd ∆ZM Vcm 80 tRH/tFH SDD22 SCC22 DJ TJ X1 X2 Y1 Y2 24 8 3 Zd Tr/Tf f0 σ ∆f 100 0 120 5 3.6 15 425 120 1600 60 1250 ohm mVpp % ps 10 100 ps ppm 170 100 50 UI mV mV ohm % V mV(RMS) ps dB dB UIpp UIpp UI UI mV mV 0.18 0.34 0.17 0.42 80 640 40 200 UIpp UIpp See 3, Fig. 5.3.2 Fig. 5.3.2 See 4, Fig. 5.3.2 20-80% Up to 8GHz 0.1-15GHz Fig. 5.3.3 Fig. 5.3.3 Fig. 5.3.3 Fig. 5.3.3 AC Coupled PECL 20-80% Baud/64 -100 Up to 100MHz V.S. Baud/64 Sinusoidal jitter tolerance for Telecom and Datacom respectively given by XFP MSA specification. Mask coordinate X1=0.205 if total non-DDJ is measured. Out of 410mV,50mV is allocated for multiple reflection. Differential Return Loss given be equation SDD22(dB)=8-22.66 log10(f/5.5), f=frequency(GHz) Changes for the Better UQ9-07-005(XF-10K) (7/15) Mitsubishi Electric Corp. Datasheet MITSUBISHI OPTICAL DEVICES MF-10KSXA-007ZA 10Gbps 1310nm XFP Optical Transceiver HOST BOARD Transmitter Interface Point XFP module Connector ASIC/SerDes Receiver Interface Point Reference Clock Absolute Amplitude Absolute Amplitude Fig. 5.3.1 XFP Module Electrical Interface Point Y2 Y1 0.0 -Y1 -Y2 0.0 X1 1-X1 Normalized Time (UI) 1.0 Fig. 5.3.2 Transmitter Differential Input Compliance Mask Changes for the Better Y2 Y1 0.0 -Y1 -Y2 0.0 X1 X2 1-X2 1-X1 1.0 Normalized Time (UI) Fig. 5.3.3 Receiver Differential Output Compliance Mask UQ9-07-005(XF-10K) (8/15) MITSUBISHI OPTICAL DEVICES Mitsubishi Electric Corp. Datasheet MF-10KSXA-007ZA 10Gbps 1310nm XFP Optical Transceiver 5.4 Low Speed Electrical Interface XFP Module low speed electrical interface specification is shown in Table 5.4.1. Table 5.4.1 Low Speed Electrical Interface Symbol Min. Max. Unit VIH 2.0 VDD3+0.3 V -0.3 0.8 V VIL Parameter LVTTL-I (Tx_Dis, P_Down/RST) LVTTL-O (Interrupt, Mod_Nr, Rx_Los) LVTTL-I (SCL, SDA) Tc : -5 to +70degC Note VDD3 as same as Pull-up Vcc VOH VDD3-0.5 VDD3+0.3 V VDD3 as same as Pull-up Vcc VOL VIH VIL 0.0 VDD3*0.7 -0.3 0.4 VDD3+0.5 VDD3*0.3 V V V VDD3 as same as Pull-up Vcc VDD3 as same as Pull-up Vcc LVTTL-O (SCL, SDA) VOH VDD3-0.5 VDD3+0.3 V VDD3 as same as Pull-up Vcc VOL 0.0 0.4 V Leakage Current Il -10 10 uA Capacitance for XFP SCL and SDA I/O Pin Ci 14 pF 100 pF 400 pF Total bus capacitance load for SCL and for SDA Cb XFP At 400kHz, 3.0kohm Rp, max At 100kHz, 8.0kohm Rp, max At 400kHz, 0.80kohm Rp, max At 100kHz, 2.0kohm Rp, max Host Host_Vcc Rp SDA or SCL line Fig. 5.4.1 An Example Open Drain Type Connection for I2C Changes for the Better UQ9-07-005(XF-10K) (9/15) MITSUBISHI OPTICAL DEVICES Mitsubishi Electric Corp. Datasheet MF-10KSXA-007ZA 10Gbps 1310nm XFP Optical Transceiver 6. Optical Characteristics All parameters are specified over the operating case temperature. 6.1 SONET SDH 2km/ IEEE 10km Optical Characteristics Table 6.1.1 Optical Characteristics Parameter Bit Rate Tc : -5 to +70degC Symbol Min Typ. Max Unit B 9.953 - 11.0957 Gbps - 1290 Note Transmitter Part Center Wavelength Optical Source Optical Output Power Shutdown Optical Power Extinction Ratio with Filter Optical Modulation Amplitude Side Mode Suppression Ratio Eye Mask *1 Snom Sidle ER OMA SMSR - 1330 DFB -6 -1 -30 6 -5.2 30 GR-253-CORE / ITU-T G.691 IEEE802.3ae nm dBm dBm dB dBm dB - 10.3Gbps Fig.6.1.1 10.3Gbps, Fig.6.1.2 Receiver Part Center Wavelength 1290 Sensitivity Overload OL 0 Stressed Sensitivity in OMA Maximum Reflectance *1 : Eye mask compliance is shown in Fig.6.1.1 and Fig.6.1.2. 1330 -11 nm dBm dBm dBm dB -10.3 -14 @BER=10-12 10.3Gbps, @BER=10-12 0.40 0.60 1.40 1.4 1 0.75 1 0.75 0.72 0.50 0.25 0 -0.25 0.28 0.25 0 -0.40 0 Fig. 6.1.1 0.2UI 1 UI MASK for GR-253/G.691 Changes for the Better 0 0.25 Fig. 6.1.2 0.45 0.55 0.75 1 UI MASK for IEEE802.3ae UQ9-07-005(XF-10K) (10/15) Mitsubishi Electric Corp. Datasheet MITSUBISHI OPTICAL DEVICES MF-10KSXA-007ZA 10Gbps 1310nm XFP Optical Transceiver 7. 2-Wire Serial Interface XFP module has 2-Wire Serial Interface (SDA, SCL), which allows host to monitor some operating parameters and to set some parameters to control the XFP module. As for the detail information of 2-Wire Interface, please see the XFP MSA specification document. 7.1 Digital Diagnostic Functions Digital Diagnostic Functions are provided using 2-Wire Interface. function to Host. It provides the following operating monitoring 1) Internally Measured Transceiver Temperature Represented as a 16 bit signed twos compliment value in increments of 1/256 degrees Celsius valid. The accuracy is better than +/-3 degrees Celsius over specified operating case temperature and voltage. 2) Measured TX Bias Current in uA Represented as a 16 bit unsigned integer with the current defined as the full 16 bit value with LSB equal to 2uA, yielding a total measurement range of 0 to 131uA. The accuracy is better than +/-10% over specified operating case temperature and voltage. 3) Measured Tx Output Power in mW Represented as a 16 bit unsigned integer with the power defined as the full 16 bit value with LSB equal to 0.1uW, yielding a total measurement range of 0 to 6.5535mW (8.2dBm). Data is based on measurement of laser monitor photodiode current. The accuracy is better than +/-2dB over specified operating case temperature and voltage. 4) Measured RX Received Optical Power in mW Value can represent either the average received power. Represented as a 16 bit unsigned integer with the power defined as the full 16 bit value with LSB equal to 0.1uW, yielding a total measurement range of 0 to 6.5535mW (+8.2dBm). The accuracy is better than +/-2dB over specified operating case temperature and voltage. 5) Internally Measured Transceiver Supply Voltage Represented as a 16 bit unsigned integer with the voltage defined as the full 16 bit value with LSB equal to 100uV, yielding a total measurement range of 0 to +6.55V. The accuracy is better than +/- 3% over specified operating case temperature and voltage. Changes for the Better UQ9-07-005(XF-10K) (11/15) Mitsubishi Electric Corp. Datasheet MITSUBISHI OPTICAL DEVICES MF-10KSXA-007ZA 10Gbps 1310nm XFP Optical Transceiver 8. General Outline Drawing Changes for the Better UQ9-07-005(XF-10K) (12/15) Mitsubishi Electric Corp. Datasheet MITSUBISHI OPTICAL DEVICES MF-10KSXA-007ZA 10Gbps 1310nm XFP Optical Transceiver 9. Environment Considerations 9.1 Mechanical Shock MIL-STD-883 Method 2002 9.2 Mechanical Vibration MIL-STD-883 Method 2004 9.3 Thermal Shock MIL-STD-883 Method 1011 9.4 Laser Class Class 1 Laser Products 9.5 ESD IEC 610004-2, 500V, HBM 10. Reference Document 1) 10 Gigabit Small Form Factor Pluggable Module (XFP) Multi-Source Agreement (MSA), Rev 4.0 – April 2003. http://www.xfpmsa.org/XFP_SFF_INF_8077i_Rev4_0.pdf Changes for the Better UQ9-07-005(XF-10K) (13/15) Mitsubishi Electric Corp. Datasheet MITSUBISHI OPTICAL DEVICES MF-10KSXA-007ZA 10Gbps 1310nm XFP Optical Transceiver 11. Ordering Information 11.1 Transceiver Type Number Type Number MF-10KSXA-007ZA Features MITSUBISHI Standard type (1310nm 2km/10km version) Optical Connector LC Receptacle 11.2 Optional Test Board Type Number Features XFP Test Board Please refer following figure. Changes for the Better UQ9-07-005(XF-10K) (14/15) Mitsubishi Electric Corp. Datasheet MITSUBISHI OPTICAL DEVICES MF-10KSXA-007ZA 10Gbps 1310nm XFP Optical Transceiver History Note MITSUBISHI ELECTRIC CORPORATION reserves the right to make changes to the production or information contains herein without notice. Customer versions are available for large quantities. Please ask MITSUBISHI ELECTRIC CORPORATION. The End of This Document Changes for the Better UQ9-07-005(XF-10K) (15/15)