MPD IG13615 Ig120 sery Datasheet

IG120 Series
High Isolation
IGBT Driver
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
Input
• Operates With xx962 Drivers
• Independent Outputs
• EN 60950 Approved
• 3,000 VAC Isolation
• Miniature SIP Case
• >3.5 MHour MTBF
• Seven Standard Models
• LOW COST!!
Parameter
Supply Voltage Range
Input Filter
Conditions
Min.
Typ.
See Model Selection Guide
Internal Capacitor
Max.
Units
Conditions
For VIN Change of 1%
See Note 1
Max.
±1.5
15
200
Units
%
%
mV P - P
%
%/ºC
Output
Parameter
Line Regulation
Load Regulation
Ripple & Noise (20 MHz)
Efficiency
Temperature Coefficient
Output Short Circuit
Min.
Typ.
±1.2
6.3
100
80
±0.03
Continuous (Autorecovery)
General
Parameter
Isolation Voltage
Isolation Resistance
Isolation Capacitance, 1 kHz/0.1V
Switching Frequency
EMI Characteristics
Parameter
Radiated Emissions
Conducted Emissions
ESD
Conditions
60 Seconds
Min.
3,000
1,000
Standard
See Page 3
EN 55022
See Page 3
EN 55022
EN 61000-4-2
Typ.
Max.
6.6
100
300
Units
VAC
M⍀
pF
kHz
Level
Class B
Class B
Criteria B; ±8 kV Contact
Environmental
Parameter
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Physical
Case Size
Case Material
Weight
Conditions
Min.
Typ.
-40
+25
-50
Free Air Convection
RH, Non-condensing
Ambient
Max.
+105
+125
Units
ºC
ºC
95
%
0.768 x 0.386 x 0.492 Inches (19.50 x 9.80 x 12.50 mm)
Non-Conductive Black Plastic (UL94-V0)
0.152 Oz (4.3g)
Reliability Specifications
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
Parameter
MTBF
Conditions
MIL HDBK 217F, 25ºC, Gnd Benign
Min.
3.5
Typ.
Max.
Units
MHours
Min.
-0.7
-0.7
-0.7
-0.7
-0.7
Typ.
Max.
13
15
16
16
26
300
Units
Absolute Maximum Ratings
Parameter
Conditions
Max Supply Voltage (1 Sec)
Lead Temperature
IG120-12
IG120-12W
IG100-9, IG100-9D
IG120-15, IG136-15
IG120-24
1.5 mm From Case For 10 Sec
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com
VDC
ºC
www.micropowerdirect.com
Model Selection Guide
Input (Supply)
Model
Number
Voltage (VDC)
Output 1
Voltage (VDC)
Output 2
Current
Current
Voltage (VDC)
Current
Load
Maximum
Regulation Capacitive Fuse Rating
Slow-Blow
(%)
Current
Load
(mA)
Min. Nom. Max. (mA Max) (mA, Min) Min. Nom. Max. (mA Max) (mA, Min)
Min.
Max.
(µF)
14.5 - 15.5
8.0
9.0
10.0
111.0
0.0
8.3
15
220
200
14.5 - 15.5
8.0
9.0
10.0
55.0
0.0
-8.0 -9.0 -10.0
55.0
0.0
8.3
15
220
200
80.0
0.0
-7.0 -8.7 -10.0
40.0
0.0
6.3
15
220
400
100.0
0.0
-7.0 -8.0 -9.0
80.0
0.0
6.3
15
220
500
80.0
0.0
-7.0 -8.7 -10.0
40.0
0.0
6.3
15
220
300
14.5 - 15.5 16.5 17.0 18.0
80.0
0.0
-7.0 -8.7 -10.0
40.0
0.0
6.3
15
220
400
23.3 - 24.7 14.0 15.0 16.0
80.0
0.0
-7.0 -8.7 -10.0
40.0
0.0
6.3
15
220
200
Nom.
Range
IG100-09
15
IG100-09D
15
IG120-12
12
11.6 - 12.4 14.0 15.0 16.0
IG120-12W
12
9.0 - 15.0
14.0 15.0 16.0
IG120-15
15
14.5 - 15.5 14.0 15.0 16.0
IG136-15
15
IG120-24
24
The IG100 series is designed to
operate with the IGD962 IGBT driver.
Contact the factory for more information
Notes:
1. Load regulation is measured from 10% load to full load. Load regulation is specified
for the primary output (output 1). The load regulation of output 2 may vary slightly.
The typical load regulation for IG100-9 and IG100-9D is 8.3%.
2. Operation at no-load will not damage these units. However, they may not meet all
specifications.
3. If output 2 is not used, it should be left open.
4. It is recommended that a fuse be used on the input of a power supply for protection.
See the Model Selection table above for the correct rating.
Efficiency vs Input Voltage 15 VDC Input
Efficiency vs Output Load 15 VDC Input
Efficiency vs Input Voltage 24 VDC Input
Efficiency vs Output Load 24 VDC Input
292 Page Street Ste D Stoughton, MA 02072
• TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]
www.micropowerdirect.com
Typical Connection
The IG100 series may be used in a wide variety of on-board power
distribution applications. However, it has been designed specifically to
power 962 type IGBT drivers. A typical connection to the MicroPower
Direct IGD962 is shown in the diagram above.
Go to the MPD website for complete information on our wide
line of IGBT driver products, including the IGD962. Or contact
the factory with any technical inquiries.
Some notes on this circuit (starting with the IG120-15
input) are:
1. The IG100 DC/DC should be mounted as close to the IGBT driver as
possible, to minimize the length of connecting board traces or wires.
2. The IG100 series does not include overload protection (typical of most
low power DC/DC’s). It is recommended that an external fuse be used.
The recommended fuse is shown in the model chart on page 2.
3. The addition of the input filter components (C1 and LDM) will typically
bring the circuit within the limits of EN 55022 Class B. The recommended values for these components are shown in the table at right.
If meeting EN 55022 class B is not a concern, the inductor (LDM) can
be eliminated (as shown in the circuit diagram below). In this case, the
recommended value for C1 is 100 µF/35V.
4. The recommended values for the output filter capacitors C2 and C3
are shown in the table at right.
5. C1, C2 and C3 should be mounted as close to the unit as possible. To
ensure peak gate current, these capacitors should have a low ESR.
The trace (or wire) between the DC/DC and the driver circuit should
be as short as possible.
6. The average output power of the driver circuit must be lower than
output power of the DC/DC.
Derating Curve
7. Recommended values for components are:
Component
C1
LDM
C2
C3
15 VIN
4.7 µF/50V
12 µH
100 µF/35V
100 µF/35V
12 VIN
4.7 µF/50V
12 µH
100 µF/35V
100 µF/35V
MicroPower Direct
•
24 VIN
4.7 µF/50V
12 µH
100 µF/35V
100 µF/35V
292 Page Street Ste D Stoughton, MA 02072
• TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]
www.micropowerdirect.com
Mechanical Dimensions
Pin Connections
Pin
Functio
Function
1
2
5
6
7
+Vin
Gnd
Vout 2
Common
Commo
Vout 1
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.02 (±0.50)
• Pin 5 on the IG100-09 has no connection
Packing Tube Dimensions
Notes:
•
•
•
•
Tube length equals 20.866 (530), unit quantity equals 25 pcs.
Tube length equals 8.661 (220), unit quantity equals 10 pcs.
All dimensions are typical in inches (mm)
Tolerance x.xx = ±0.02 (±0.50)
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: [email protected]
Similar pages