Wall FEMFA-1275 Dc/dc converter Datasheet

TECHNICAL DATASHEET
Rev B
FEMFA-1275
MIL-STD-1275D
Front End Filter Module for FA Series DC/DC Converters
APPLICATIONS
 MIL-STD-1275D 28V Vehicle Electrical
System Compliance
 Voltage Surge and Spike Filtering
FEATURES
 Surge and Spike Protection for up to 350 Watts
 Allows FA Series to Operate Through MIL-STD-1275
Disturbances
DESCRIPTION
The Wall Industries Front End Filter Module (FEMFA-1275) was designed with the FA Series DC-DC
converters in mind. This Module will allow an FA series DC-DC converter to be used safely in 28V Vehicle
Electrical System requirements set forth by MIL-STD-1275D. Other requirements such as MIL-STD-461E may
apply but are not discussed in this data sheet and additional circuitry may be required.
(888) 597-WALL
www.wallindustries.com
1 of 9
TECHNICAL DATASHEET
Rev B
FEMFA-1275
MIL-STD-1275D Test Results
Detailed Requirements
Test Conditions
5.1.2.1
Starting Disturbances
5.1.2.2
Vehicle System Voltage
Initial Engagement Surges pulsed to 6V for less than
1 Second.
5.1.2.3
Cranking Level
5.1.3
Normal Operation Mode
5.1.3.1
Steady-state Voltage
Detailed Results
Figure or Picture
No damage to converter.
Photo 1.
Converter operates
normally before, and after.
Vehicle System Voltage at No damage to converter.
Photo 2.
16V for 30 Seconds.
Converter operates
Returned to 28V for 1
normally before, and after.
Minute 30 Seconds, and
repeated 2 more times.
Vehicle System Voltage =
25 – 30V.
No damage to converter.
Converter operates
normally before, during,
and after.
Photo 3.
5.1.3.2
Ripple
Vehicle System Voltage =
25 – 30V with ±2V ripple,
Frequency @ 50Hz,
12kHz, 48kHz and
200kHz
No damage to converter.
Converter operates
normally before, during,
and after.
Figure 1.
5.1.3.3
Surges
Vehicle System Voltage =
25 – 30V. Pulse of +40V,
50mS duration imported.
No damage to converter.
Converter operates
normally before, during,
and after.
Photo 4 and Figure 2.
5.1.3.4
Spikes
Vehicle System Voltage =
25 - 30V. Pulse of
±250V, 70µS duration
No damage to converter.
Converter operates
normally before, during,
and after.
Photo 6 and Figure 3.
(888) 597-WALL
www.wallindustries.com
Page 2 of 9
Rev B
5.1.4
Generator-Only Mode
5.1.4.1
Steady-State Voltage
TECHNICAL DATASHEET
FEMFA-1275
Vehicle System Voltage =
23 – 33V.
No damage to converter.
Converter operates
normally before, during,
and after.
Photo 3.
5.1.4.2
Ripple
Vehicle System Voltage =
23 – 33V with ±7V ripple,
Frequency @ 50Hz,
12kHz, 48kHz and
200kHz
No damage to converter.
Converter operates
normally before, during,
and after.
Figure 1.
5.1.4.3
Surges
Vehicle System Voltage =
23 – 33V. Pulse of
+100V, 50mS duration
imported.
No damage to converter.
Converter should operate
normally before, during
and after. Output of Filter
Module will be briefly
interrupted and PS
Control will be pulled
low.
Photo 5 and Figure 2.
5.1.4.4
Spikes
Vehicle System Voltage =
23 – 33V
No damage to converter.
Converter operates
normally before, during,
and after.
Photo 6 and Figure 3.
5.3.2.2
Voltage Spikes Exported
Vehicle System Voltage =
23 - 33V.
No spikes, outside of
Normal Operating Mode
were transmitted to
converter.
(888) 597-WALL
www.wallindustries.com
Page 3 of 9
TECHNICAL DATASHEET
Rev B
FEMFA-1275
Graph 1: De-rating Curve of FEMFA-1275
Output power (watts)
Maximum power Derating Curve during
MIL-STD-1275D 100v pulse
200
190
180
170
160
150
140
130
120
110
100
90
80
70
60
50
40
30
20
10
0
-40
-20
0
20
40
60
80
100
Ambient Temperature Degrees Celsius
Max case temperature: 100 degrees Celsius
Max average current (under normal operating voltages): 15 amps
Max peak single pulse current less than 50ms (under normal operating voltages): 50 amps
(888) 597-WALL
www.wallindustries.com
Page 4 of 9
Rev B
TECHNICAL DATASHEET
FEMFA-1275
Photo 1: Ch1 – Vin;
Ch2 – Vout of FA Module
Photo 2: Ch1 – Vin;
Ch2 – Vout of FA Module
Photo 3: Ch1 – Vin;
Ch2 – Vout
Photo 4: Ch1 - Vin
Photo 5: Ch1 – Vin
Photo 6: Ch1 - Vin
(888) 597-WALL
www.wallindustries.com
Page 5 of 9
Rev B
TECHNICAL DATASHEET
FEMFA-1275
Figure 1: Ripple Test Set-Up
Figure 2: Imported Surge Test Set-Up
(888) 597-WALL
www.wallindustries.com
Page 6 of 9
Rev B
TECHNICAL DATASHEET
FEMFA-1275
Figure 3: Imported Spikes Test Set-Up
(888) 597-WALL
www.wallindustries.com
Page 7 of 9
TECHNICAL DATASHEET
Rev B
FEMFA-1275
Figure 4: Mechanical Dimensions
Unit: inches [mm]
.18 4.7
2.000 50.80
.700 17.78
3
6
.350 8.89
2
5
0 0
1
4
.42 10.7
PIN DESIGNATIONS
FOR REFERENCE ONLY
COVER
SEE NOTE-6
PIN-2 SOLDERED
TO COVER REF.
.20 MIN [5.1 MIN]
SEE NOTE-2 & 3
DATE CODE
SERIAL NO:
FEMFA-XX
.51 13
A
LABEL
.112 (NO:4)-40 UNC-2B 4X
.10 [2.5] MAX SCREW DEPTH FROM SURFACE-A
MAX RECEIVING TORQUE: 6.0 LBS/in [0.68 N/m]
.02 0.5 STANDOFF FEET 4X
CASE
SEE NOTES-5
.01 FIM
HEAT-SINK SURFACE REF.
PIN DESIGNATION TABLE
1.54 39.1
1.030 26.16
PIN
1
2
3
4
5
6
DESCRIPTION
+ Vin
CHASSIS GROUND
-Vin
+Vout
ENABLE
-Vout
PIN DIA.
.062 [1.54]
.040 [1.02]
.062 [1.54]
.062 [1.54]
.062 [1.54]
.062 [1.54]
.26 6.5
.26 6.5
1.860 47.24
2.37 60.2
UNLESS OTHERWISE SPECIFIED
ALL DIM ARE IN INCHES
[XX] ARE IN MILLIMETERS
APPLIED TOLERANCES
ANGLES ±1°
.XX= ±.02 [0.3] .XXX= ±.010 [0.25]
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.5M - 1994
NOTES:
1. 3D MODEL DRAWING ML106546 AVAILABLE.
2. PIN TO PIN TOLERANCE: +/- .010 [+/- 0.25].
3. PIN DIAMETER TOLERANCE: +/- .005 [+/- 0.13].
4. UNIT HAS 6-SIDE SHIELDING.
5. CASE MATERIAL: .040 [1.02] THICK, ALUMINUM. FINISH: ANODIZED.
6. COVER MATERIAL: STEEL. FINISH: TIN PLATED TO MEET RoHS.
THIRD ANGLE PROJECTION
(888) 597-WALL
www.wallindustries.com
Page 8 of 9
Rev B
TECHNICAL DATASHEET
FEMFA-1275
COMPANY INFORMATION
Wall Industries, Inc. has created custom and modified units for over 50 years. Our in-house research and
development engineers will provide a solution that exceeds your performance requirements on time and on budget.
Our ISO9001-2008 certification is just one example of our commitment to producing a high quality, welldocumented product for our customers.
Our past projects demonstrate our commitment to you, our customer. Wall Industries, Inc. has a reputation for
working closely with its customers to ensure each solution meets or exceeds form, fit and function requirements.
We will continue to provide ongoing support for your project above and beyond the design and production phases.
Give us a call today to discuss your future projects.
Contact Wall Industries for further information:
Phone:
Toll Free:
Fax:
E-mail:
Web:
Address:
(888) 597-WALL
(603)778-2300
 (888)587-9255
 (603)778-9797
[email protected]
www.wallindustries.com
5 Watson Brook Rd.
Exeter, NH 03833
www.wallindustries.com
Page 9 of 9
Similar pages