TI1 BQ24080DRCRG4 1-a, single-chip, li-ion and li-pol charger ic Datasheet

bq24080
bq24081
SLUS698E – MARCH 2006 – REVISED AUGUST 2011
www.ti.com
1-A, SINGLE-CHIP, LI-ION AND LI-POL CHARGER IC
Check for Samples: bq24080, bq24081
FEATURES
1
•
2
•
•
•
•
•
•
•
Integrated Power FET and Current Sensor for
Up to 1-A Charge Applications From AC
Adapter
Precharge Conditioning With Safety Timer
Charge and Power-Good Status Output
Automatic Sleep Mode for Low Power
Consumption
Integrated Charge-Current Monitor
Fixed 7-Hour Fast Charge Safety Timer
Ideal for Low-Dropout Charger Designs for
Single-Cell Li-Ion or Li-Pol Packs in
Space-Limited Portable Applications
Small 3-mm × 3-mm SON Package
APPLICATIONS
•
•
PDAs, MP3 Players
Digital Cameras
•
•
Internet Appliances
Smartphones
DESCRIPTION
The bq24080 and bq24081 are highly integrated and
flexible Li-Ion linear charge devices targeted at
space-limited charger applications. They offer an
integrated power FET and current sensor,
high-accuracy current and voltage regulation, charge
status, and charge termination, in a single monolithic
device. An external resistor sets the magnitude of the
charge current.
The device charges the battery in three phases:
conditioning, constant current, and constant voltage.
Charge is terminated based on minimum current. An
internal charge timer provides a backup safety for
charge termination. The device automatically restarts
the charge if the battery voltage falls below an
internal threshold. The device automatically enters
sleep mode when the ac adapter is removed.
AC
Adapter
VDC
GND
C1
0.1 mF
PACK+
bq24080
1
IN
C2
0.1 µF
OUT 10
PACK–
2
NC
CE
9
3
STAT1
PG
8
4
STAT2 VBSEL 7
5
VSS
Battery Pack
+
System
System
Interface
RSET
ISET
6
1.13 kW
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006–2011, Texas Instruments Incorporated
bq24080
bq24081
SLUS698E – MARCH 2006 – REVISED AUGUST 2011
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION
TJ
CHARGE
REGULATION
VOLTAGE (V)
FUNCTIONS
FAST-CHARGE
TIMER (HOURS)
–40°C to 125°C
4.2
CE and PG
7
–40°C to 125°C
4.2
TE and TS
7
(1)
(2)
PART
NUMBER (1)
MARKINGS
(2)
bq24080DRCR
BRO
bq24080DRCT
bq24081DRCR
BRP
bq24081DRCT
The DRC package is available taped and reeled only in quantities of 3,000 devices per reel.
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
Web site at www.ti.com.
DISSIPATION RATINGS
(1)
PACKAGE
RθJA
RθJC
TA < 40°C
POWER RATING
DERATING FACTOR
ABOVE TA = 40°C
DRC (1)
46.87 °C/W
4.95 °C/W
1.5 W
0.021 W/°C
This data is based on using the JEDEC High-K board and the exposed die pad is connected to a copper pad on the board. This is
connected to the ground plane by a 2- × 3-via matrix.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range unless otherwise noted (1)
bq24080, bq24081
VI
Input voltage (2)
IN, CE, ISET, OUT, PG, STAT1, STAT2, TE, TS
Output sink/source current
Output current
V
STAT1, STAT2, PG
15
mA
OUT
1.5
TA
Operating free-air temperature range
TJ
Junction temperature range
Tstg
Storage temperature
(1)
(2)
UNIT
–0.3 to 7
A
°C
–40 to 125
°C
–65 to 150
°C
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are with respect to VSS.
RECOMMENDED OPERATING CONDITIONS
MIN
VCC
Supply voltage
TJ
Operating junction temperature range
2
MAX
UNIT
4.5
6.5
V
0
125
°C
Copyright © 2006–2011, Texas Instruments Incorporated
bq24080
bq24081
SLUS698E – MARCH 2006 – REVISED AUGUST 2011
www.ti.com
ELECTRICAL CHARACTERISTICS
over 0°C ≤ TJ ≤ 125°C and recommended supply voltage (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
1.2
2
2
5
UNIT
INPUT CURRENT
VCC current
VCC > VCC(min)
ICC(SLP)
Sleep current
Sum of currents into OUT pin,
VCC < V(SLP)
ICC(STBY)
Standby current
CE = High, 0°C ≤ TJ ≤ 85°C
IIB(OUT)
Input current on OUT pin
Charge DONE, VCC > VCC(MIN)
ICC(VCC)
150
1
mA
μA
5
VOLTAGE REGULATION VO(REG) + V(DO−MAX) ≤ VCC, I(TERM) < IO(OUT) ≤ 1 A
VO(REG)
Output voltage
Voltage regulation accuracy
V(DO)
Dropout voltage (V(IN) − V(OUT))
4.2
TA = 25°C
V
−0.35%
0.35%
−1%
1%
VO(OUT) = VO(REG), IO(OUT) = 1 A
VO(REG) + V(DO)) ≤ VCC
350
500
mV
1000
mA
V
CURRENT REGULATION
IO(OUT)
Output current range (1)
VI(OUT) > V(LOWV),
VI(IN) − VI(OUT) > V(DO),
VCC ≥ 4.5 V
V(SET)
Output current set voltage
Voltage on ISET pin, VCC ≥ 4.5 V,
VI ≥ 4.5 V, VI(OUT) > V(LOWV),
VI − VI(OUT) > V(DO)
K(SET)
Output current set factor
20
2.463
2.5
2.538
50 mA ≤ IO(OUT) ≤ 1 A
307
322
337
10 mA ≤ IO(OUT) < 50 mA
296
320
346
1 mA ≤ IO(OUT) < 10 mA
246
320
416
PRECHARGE AND SHORT-CIRCUIT CURRENT REGULATION
Precharge to fast-charge transition
threshold
Voltage on OUT pin
2.8
3
3.2
V
Deglitch time for fast-charge to
precharge transition
VCC(MIN) ≥ 4.5 V, tFALL = 100 ns,
10-mV overdrive,
VI(OUT) decreasing below threshold
250
375
500
ms
IO(PRECHG)
Precharge range (2)
0 V < VI(OUT) < V(LOWV), t < t(PRECHG)
2
100
mA
V(PRECHG)
Precharge set voltage
Voltage on ISET pin,
VO(REG) = 4.2 V,
0 V < VI(OUT) > V(LOWV), t < t(PRECHG)
240
270
mV
100
mA
V(LOWV)
255
TERMINATION DETECTION
I(TERM)
Charge termination detection
range (3)
VI(OUT) > V(RCH), t < t(TRMDET)
2
V(TERM)
Charge termination detection set
voltage
Voltage on ISET pin,
VO(REG) = 4.2 V,
VI(OUT) > V(RCH), t < t(TRMDET)
235
250
265
mV
tTRMDET
Deglitch time for termination
detection
VCC(MIN) ≥ 4.5 V, tFALL = 100 ns
charging current decreasing below
10-mV overdrive
250
375
500
ms
(1)
(2)
(3)
See Equation 2 in the Function Description section.
See Equation 1 in the Function Description section.
See Equation 4 in the Function Description section.
Copyright © 2006–2011, Texas Instruments Incorporated
3
bq24080
bq24081
SLUS698E – MARCH 2006 – REVISED AUGUST 2011
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
over 0°C ≤ TJ ≤ 125°C and recommended supply voltage (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
VO(REG)
– 0.115
VO(REG)
− 0.10
VO(REG)
− 0.085
250
375
500
ms
0.25
V
BATTERY RECHARGE THRESHOLD
V(RCH)
Recharge threshold
t(DEGL)
Deglitch time for recharge detect
VCC(MIN) ≥ 4.5 V, tFALL = 100 ns
decreasing below or increasing
above threshold, 10-mV overdrive
V
STAT1, STAT2, and PG OUTPUTS
VOL
Low-level output saturation voltage
IO = 5 mA
CE and TE INPUTS
VIL
Low-level input voltage
0
VIH
High-level input voltage
1.4
IIL
Low-level input current
–1
IIH
High-level input current
0.4
1
V
μA
TIMERS
t(PRECHG)
Precharge time
t(CHG)
Charge time
I(FAULT)
Timer fault recovery current
1,584
1,800
2,016
22,176
25,200
28,224
s
s
μA
200
SLEEP COMPARATOR
V(SLP)
Sleep-mode entry threshold voltage
V(SLPEXIT)
Sleep-mode exit threshold voltage
2.3 V ≤ VI(OUT) ≤ VO(REG)
Sleep-mode entry deglitch time
V(IN) decreasing below threshold,
tFALL = 100 ns, 10-mV overdrive
VCC ≤ VI(OUT)
+ 80 mV
VCC ≥ VI(OUT)
+ 190
250
375
500
V
ms
THERMAL SHUTDOWN THRESHOLDS
T(SHTDWN)
Thermal trip threshold
Thermal hysteresis
165
TJ increasing
°C
15
UNDERVOLTAGE LOCKOUT
UVLO
Undervoltage lockout
Decreasing VCC
2.4
Hysteresis
2.5
2.6
27
V
mV
TEMPERATURE SENSE COMPARATOR (bq24081)
V(TS1)
High-voltage threshold
2.475
2.5
2.525
V(TS2)
Low-voltage threshold
0.485
0.5
0.515
I(TS)
TS pin current source
96
102
108
μA
t(DEGL)
Deglitch time for temperature fault
250
375
500
ms
4
V
Copyright © 2006–2011, Texas Instruments Incorporated
bq24080
bq24081
SLUS698E – MARCH 2006 – REVISED AUGUST 2011
www.ti.com
PIN ASSIGNMENT
DRC PACKAGE
(TOP VIEW)
VSS
5
STAT2 STAT1 GND
IN
VSS
3
1
5
4
2
STAT2 STAT1 GND
IN
3
1
4
bq24080
6
7
ISET GND
8
PG
2
bq24081
9
10
CE
OUT
6
7
ISET GND
8
TE
9
10
TS
OUT
P0051-01
PIN FUNCTIONS
PIN
NAME
CE
NO.
I/O
DESCRIPTION
bq24080
bq24081
9
–
I
Charge enable input (active-low)
2, 7
2, 7
–
Ground
IN
1
1
I
Adapter dc voltage. Connect minimum 0.1-μF capacitor to VSS.
ISET
6
6
I
Charge current. External resistor to VSS sets precharge and fast-charge current, and also the
termination current value. Can be used to monitor the charge current.
OUT
10
10
O
Charge current output. Connect minimum 0.1-μF capacitor to VSS.
PG
8
–
O
Power-good status output (open-drain)
STAT1
3
3
O
STAT2
4
4
O
TE
–
8
I
TS
–
9
I/O
VSS
5
5
–
Ground
Thermal
pad
–
–
–
There is an internal electrical connection between the exposed thermal pad and the VSS pin of the
device. The exposed thermal pad must be connected to the same potential as the VSS pin on the
printed-circuit board. Do not use the thermal pad as the primary ground input for the device.
The VSS pin must be connected to ground at all times.
GND
Charge status outputs (open-drain)
Timer-enable input (active-low)
Temperature sense; connect to NTC in battery pack.
Copyright © 2006–2011, Texas Instruments Incorporated
5
bq24080
bq24081
SLUS698E – MARCH 2006 – REVISED AUGUST 2011
www.ti.com
FUNCTIONAL BLOCK DIAGRAM
(3)
IN
OUT
ISET
V(PRECHG)
V(SET)
VO(REG)
V(RCH)
V(LOWV)
(3)
(3)
(3)
V(TERM)
V(IN)
ITS
VI(OUT) + V(SLP)
(3)
V(TS1)
V(UVLO)
(2)
Charge
Control,
Timers,
and
Status
TS
(3)
V(TS2)
STAT1
CE
(1)
STAT2
(2)
TE
(1)
PG
VSS
B0193-01
6
(1)
bq24080 only
(2)
bq24081 only
(3)
Signal deglitched
Copyright © 2006–2011, Texas Instruments Incorporated
bq24080
bq24081
SLUS698E – MARCH 2006 – REVISED AUGUST 2011
www.ti.com
TYPICAL CHARACTERISTICS
DROPOUT VOLTAGE
vs
JUNCTION TEMPERATURE
450
IO(OUT) = 1000 mA
400
Dropout Voltage - mV
350
IO(OUT) = 750 mA
300
250
IO(OUT) = 500 mA
200
150
IO(OUT) = 250 mA
100
50
0
0
50
100
o
TJ - Junction Temperature - C
150
Figure 1.
Figure 2. VIN Hot-Plug Power-Up Sequence
Copyright © 2006–2011, Texas Instruments Incorporated
7
bq24080
bq24081
SLUS698E – MARCH 2006 – REVISED AUGUST 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
Figure 3. Charge Enable Power-Up Sequence (CE = High-to-Low)
Figure 4. Battery Hot-Plug During Charging Phase
8
Copyright © 2006–2011, Texas Instruments Incorporated
bq24080
bq24081
SLUS698E – MARCH 2006 – REVISED AUGUST 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
(6) Deglitch timer expires – charge done is declared.
Figure 5. Battery Hot-Plug and Removal Power Sequence
Copyright © 2006–2011, Texas Instruments Incorporated
9
bq24080
bq24081
SLUS698E – MARCH 2006 – REVISED AUGUST 2011
www.ti.com
FUNCTIONAL DESCRIPTION
The device supports a precision Li-Ion, Li-Pol charging system suitable for single cells. Figure 6 shows a typical
charge profile, and Figure 7 shows an operational flow chart.
Preconditioning
Phase
Current Regulation Phase
Voltage Regulation and Charge Termination Phase
Regulation
Voltage
Regulation
Current
Minimum
Charge
Voltage
PreConditioning
and Term
Detect
Charge
Voltage
Charge
Complete
Charge
Current
Safety Timer
M0066-01
Figure 6. Typical Charging Profile
10
Copyright © 2006–2011, Texas Instruments Incorporated
bq24080
bq24081
SLUS698E – MARCH 2006 – REVISED AUGUST 2011
www.ti.com
POR
SLEEP MODE
VCC > VI(OUT)
checked at all
times?
No
Indicate SLEEP
MODE
Yes
VI(OUT)<V(LOWV)
?
Yes
Regulate
IO(PRECHG)
and
Indicate ChargeIn-Progress
Reset and Start
t(PRECHG) Timer
No
Reset All Timers,
Start t(CHG) Timer
Regulate Current
or Voltage
and
Indicate ChargeIn-Progress
No
VI(OUT)<V(LOWV)
?
Yes
Yes
t(CHG) Expired?
t(PRECHG)
Expired?
No
No
Yes
Yes
Fault Condition
Yes
VI(OUT)<V(LOWV)
?
Indicate Fault
No
No
Yes
Iterm
Detection
?
VI(OUT) >V(RCH)
?
No
Yes
Enable I(FAULT)
Current
Turn Off Charge
Indicate DONE
VI(OUT) >V(RCH)
?
No
Yes
VI(OUT) <V(RCH)
?
No
Disable I(FAULT)
Current
Yes
F0018-01
Figure 7. Operational Flow Chart
Copyright © 2006–2011, Texas Instruments Incorporated
11
bq24080
bq24081
SLUS698E – MARCH 2006 – REVISED AUGUST 2011
www.ti.com
Battery Preconditioning
During a charge cycle, if the battery voltage is below the V(LOWV) threshold, the device applies a precharge
current, IO(PRECHG), to the battery. This feature revives deeply discharged cells. Resistor RSET, connected
between the ISET and VSS, determines the precharge rate. The V(PRECHG) and K(SET) parameters are specified in
the Electrical Characteristics table.
K(SET) x V(PRECHG)
IO(PRECHG) =
RSET
(1)
The device activates a safety timer, t(PRECHG), during the conditioning phase. If the V(LOWV) threshold is not
reached within the timer period, the device turns off the charger and enunciates FAULT on the STATx pins. See
the Timer Fault Recovery section for additional details.
Battery Fast-Charge Constant Current
The device offers on-chip current regulation with programmable set point. Resistor RSET, connected between the
ISET and VSS, determines the charge rate. The V(SET) and K(SET) parameters are specified in the specifications
table.
K(SET) x V(SET)
IO(OUT) =
RSET
(2)
Charge-Current Monitor
When the charge function is enabled internal circuits generate a current proportional to the charge current at the
ISET pin. This current, when applied to the external charge current programming resistor RISET generates an
analog voltage that can be monitored by an external host to calculate the current sourced from the OUT pin.
R ISET
V(ISET) + I(OUT)
K(SET)
(3)
Battery Fast-Charge Voltage Regulation
The voltage regulation feedback is through the OUT pin. This input is tied directly to the positive side of the
battery pack. The device monitors the battery-pack voltage between the OUT and VSS pins. When the battery
voltage rises to the VO(REG) threshold, the voltage regulation phase begins and the charging current begins to
taper down.
As a safety backup, the device also monitors the charge time in the charge mode. If charge is not terminated
within this time period, t(CHG), the charger is turned off and FAULT is set on the STATx pins. See the Timer Fault
and Recovery section for additional details.
Charge Termination Detection and Recharge
The device monitors the charging current during the voltage regulation phase. Once the termination threshold,
I(TERM), is detected, charge is terminated. The V(TERM) and K(SET) parameters are specified in the specifications
table.
K
x V(TERM)
IO(TERM) = (SET)
RSET
(4)
After charge termination, the device restarts the charge once the voltage on the OUT pin falls below the V(RCH)
threshold. This feature keeps the battery at full capacity at all times.
The device monitors the charging current during the voltage regulation phase. Once the termination threshold,
I(TERM), is detected, the charge is terminated immediately.
Resistor RSET, connected between the ISET and VSS, determines the current level at the termination threshold.
12
Copyright © 2006–2011, Texas Instruments Incorporated
bq24080
bq24081
SLUS698E – MARCH 2006 – REVISED AUGUST 2011
www.ti.com
Sleep Mode
The device enters the low-power sleep mode if the input power (IN) is removed from the circuit. This feature
prevents draining the battery during the absence of input supply.
Charge Status Outputs
The open-drain STAT1 and STAT2 outputs indicate various charger operations as shown in the following table.
These status pins can be used to drive LEDs or communicate to the host processor. Note that OFF indicates the
open-drain transistor is turned off.
Table 1. Status Pin Summary
CHANGE STATE
STAT1
STAT2
Precharge in progress
ON
ON
Fast charge in progress
ON
OFF
Charge done
OFF
ON
OFF
OFF
Charge suspend (temperature)
Timer fault
Sleep mode
PG Output (bq24080)
The open-drain power-good (PG) output pulls low when a valid input voltage is present. This output is turned off
(high-impedance) in sleep mode. The PG pin can be used to drive an LED or communicate to the host
processor.
Charge-Enabled (CE) Input (bq24080)
The CE digital input is used to disable or enable the charge process. A low-level signal on this pin enables the
charge and a high-level signal disables the charge and places the device in a low-power mode. A high-to-low
transition on this pin also resets all timers and timer fault conditions.
Timer Enabled (TE) Input (bq24081)
The TE digital input is used to disable or enable the fast-charge timer. A low-level signal on this pin enables the
fast-charge timer, and a high-level signal disables this feature.
TEMPERATURE QUALIFICATION (bq24081)
The bq24081 continuously monitors battery temperature by measuring the voltage between the TS and VSS pins.
An internal current source provides the bias for common 10-kΩ negative-temperature-coefficient thermistors
(NTC) (see the functional block diagram). The device compares the voltage on the TS pin with the internal V(TS1)
and V(TS2) thresholds to determine if charging is allowed. If a temperature outside the V(TS1) and V(TS2) thresholds
is detected, the device immediately suspends the charge by turning off the power FET and holding the timer
value (i.e., timers are not reset). Charge is resumed when the temperature returns within the normal range.
The allowed temperature range with a 103AT-type thermistor is 0°C to 45°C. However, the user may modify
these thresholds by adding external resistors (see Figure 8 and Figure 9
Copyright © 2006–2011, Texas Instruments Incorporated
13
bq24080
bq24081
SLUS698E – MARCH 2006 – REVISED AUGUST 2011
www.ti.com
bq24081
ITS
VHTF
PACK+
TS
NTC
VLTF
PACK–
B0194-01
Figure 8. Default Temperature Thresholds
bq24081
ITS
VHTF
PACK+
RT1
TS
NTC
RT2
VLTF
PACK–
B0195-01
Figure 9. Temperature Thresholds Modified by External Resistors
14
Copyright © 2006–2011, Texas Instruments Incorporated
bq24080
bq24081
www.ti.com
SLUS698E – MARCH 2006 – REVISED AUGUST 2011
Timer Fault and Recovery
As shown in Figure 7, the device provides a recovery method to deal with timer fault conditions. The following
summarizes this method:
Condition Number 1
OUT pin voltage is above the recharge threshold (V(RCH)), and a timeout fault occurs.
Recovery method: the device waits for the OUT pin voltage to fall below the recharge threshold. This could
happen as a result of a load on the battery, self-discharge, or battery removal. Once the OUT pin voltage falls
below the recharge threshold, the device clears the fault and starts a new charge cycle. A POR, TE, or CE toggle
also clears the fault.
Condition number 2
OUT pin voltage is below the recharge threshold (V(RCH)), and a timeout fault occurs
Recovery method: Under this scenario, the device applies the I(FAULT) current. This small current is used to detect
a battery removal condition and remains on as long as the battery voltage stays below the recharge threshold. If
the OUT pin voltage goes above the recharge threshold, then the device disables the I(FAULT) current and
executes the recovery method described for condition number 1. Once the OUT pin voltage falls below the
recharge threshold, the bq24080 clears the fault and starts a new charge cycle. A POR, TE, or CE toggle also
clears the fault.
Copyright © 2006–2011, Texas Instruments Incorporated
15
bq24080
bq24081
SLUS698E – MARCH 2006 – REVISED AUGUST 2011
www.ti.com
APPLICATION INFORMATION
bq24080/1 CHARGER DESIGN EXAMPLE
Requirements
• Supply voltage = 5 V
• Fast-charge current of approximately 750 mA
• Battery-Temperature sense (bq24081): default setting = –2°C to 44.5°C
Calculations
Program the charge current for 750 mA:
RISET = [V(SET) × K(SET) / I(OUT)]
From electrical characteristics table, V(SET) = 2.5 V.
From electrical characteristics table, K(SET) = 322.
RISET = [2.5 V × 322 / 0.75 A] = 1.073 kΩ
Selecting the closest standard value, use a 1.07-kΩ resistor connected between ISET (pin 6) and ground.
Battery Temperature Sense (bq24081):
Use a Semitec 103AT-4 NTC thermistor connected between TS (pin 9) and ground.
RTHERM-cold = [V(TS1) / I(TS) ] = 2.5V / 100 μA = 25 kΩ
RTHERM-hot = [V(TS2) / I(TS) ] = 0.5V / 100 μA = 5 kΩ
Look up the corresponding temperature value in the manufacturer's resistance-temperature table for the
thermistor selected. For a 103AT-4 Semitec thermistor:
5 kΩ = 44.5°C
25 kΩ = 2°C
STAT Pins (All Devices) and PG Pin (bq24080):
Status pins Monitored by Processor:
Select a pullup resistor that can source more than the input bias (leakage) current of both the processor and
status pins and still provide a logic high. RPULLUP ≤ [V(cc-pullup) – V(logic hi-min) / (I(µP-monitor) + I(STAT-OpenDrain)) ] =
(3.3 V – 1.9 V) / (1 μA + 1 μA) ≤ 700 kΩ; Connect a 100-kΩ pullup between each status pin and the VCC of
the processor. Connect each status pin to a μP monitor pin.
Status viewed by LED:
Select an LED with a current rating less than 10 mA and select a resistor to place in series with the LED to
limit the current to the desired current value (brightness). RLED = [(V(IN) – V(LED-on)) / I(LED)] = (5 V – 2 V) / 1.5
mA = 2 kΩ. Place an LED and resistor in series between the input and each status pin.
Selecting Input and Output Capacitors
In most applications, all that is needed is a high-frequency decoupling capacitor on the input power pin. A 0.1-μF
ceramic capacitor, placed in close proximity to the IN pin and GND pad works well. In some applications, it may
be necessary to protect against a hot plug input voltage overshoot. This is done in three ways:
1. The best way is to add an input zener, 6.2 V, between the IN pin and VSS.
2. A low-power zener is adequate for the single event transient. Increasing the input capacitance lowers the
characteristic impedance which makes the input resistance move effective at damping the overshoot, but
risks damaging the input contacts by the high inrush current.
3. Placing a resistor in series with the input dampens the overshoot, but causes excess power dissipation.
The device only requires a small capacitor for loop stability. A 0.1-μF ceramic capacitor placed between the OUT
and GND pad is typically sufficient.
16
Copyright © 2006–2011, Texas Instruments Incorporated
bq24080
bq24081
SLUS698E – MARCH 2006 – REVISED AUGUST 2011
www.ti.com
1.5 kW
SOURCE
INPUT
VDC
bq24080
C1
0.1 mF
1
IN
OUT
C2
0.1 mF
1.5 kW
GND
1.5 kW
PACK+
10
2
GND
CE
9
3
STAT1
PG
8
4
STAT2
GND
7
5
VSS
ISET
6
+
PACK–
1.13 kW
RSET
Charge Current
Translator Output
Figure 10. Typical Application Circuit
Thermal Considerations
The bq24080 and bq24081 are packaged in a thermally enhanced MLP package. The package includes a
thermal pad to provide an effective thermal contact between the device and the printed-circuit board (PCB). Full
PCB design guidelines for this package are provided in the application report entitled, QFN/SON PCB
Attachment (TI Literature Number SLUA271).
The most common measure of package thermal performance is thermal impedance (RθJA) measured (or
modeled) from the device junction to the air surrounding the package surface (ambient). The mathematical
expression for RθJA is:
RqJA =
TJ - T A
P
(5)
Where:
• TJ = device junction temperature
• TA = ambient temperature
• P = device power dissipation
Factors that can greatly influence the measurement and calculation of RθJA include:
• Orientation of the device (horizontal or vertical)
• Volume of the ambient air surrounding the device under test and airflow
• Whether other surfaces are in close proximity to the device being tested
• Use multiple 10–13 mil vias in the PowerPAD™ to copper ground plane.
• Avoid cutting the ground plane with a signal trace near the power IC.
• The PCB must be sized to have adequate surface area for heat dissipation.
• FR4 (figerglass) thickness should be minimized.
The device power dissipation, P, is a function of the charge rate and the voltage drop across the internal Power
FET. It can be calculated from the following equation:
P = (V(IN) - V(OUT)) x IO(OUT)
(6)
Due to the charge profile of Li-xx batteries, the maximum power dissipation is typically seen at the beginning of
the charge cycle when the battery voltage is at its lowest. See Figure 6.
Copyright © 2006–2011, Texas Instruments Incorporated
17
bq24080
bq24081
SLUS698E – MARCH 2006 – REVISED AUGUST 2011
www.ti.com
PCB Layout Considerations
It is important to pay special attention to the PCB layout. The following provides some guidelines:
• To obtain optimal performance, the decoupling capacitor from VCC to V(IN) and the output filter capacitors from
OUT to VSS should be placed as close as possible to the device, with short trace runs to both signal and VSS
pins. The VSS pin should have short trace runs to the GND pin.
• All low-current VSS connections should be kept separate from the high-current charge or discharge paths from
the battery. Use a single-point ground technique incorporating both the small-signal ground path and the
power ground path.
• The high-current charge paths into IN and from the OUT pins must be sized appropriately for the maximum
charge current in order to avoid voltage drops in these traces.
• The device is packaged in a thermally enhanced MLP package. The package includes a thermal pad to
provide an effective thermal contact between the device and the printed circuit board (PCB). Full PCB design
guidelines for this package are provided in the application report entitled, QFN/SON PCB Attachment
(TI Literature Number SLUA271).
18
Copyright © 2006–2011, Texas Instruments Incorporated
PACKAGE OPTION ADDENDUM
www.ti.com
30-Sep-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
BQ24080DRCR
ACTIVE
VSON
DRC
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
BRO
BQ24080DRCRG4
ACTIVE
VSON
DRC
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
BRO
BQ24080DRCT
ACTIVE
VSON
DRC
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
BRO
BQ24080DRCTG4
ACTIVE
VSON
DRC
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
BRO
BQ24081DRCR
ACTIVE
VSON
DRC
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
BRP
BQ24081DRCRG4
ACTIVE
VSON
DRC
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
BRP
BQ24081DRCT
ACTIVE
VSON
DRC
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
BRP
BQ24081DRCTG4
ACTIVE
VSON
DRC
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
BRP
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
(4)
30-Sep-2014
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
1-Oct-2014
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
BQ24080DRCR
VSON
DRC
10
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
BQ24080DRCT
VSON
DRC
10
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
BQ24081DRCR
VSON
DRC
10
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
BQ24081DRCT
VSON
DRC
10
250
180.0
12.5
3.3
3.3
1.1
8.0
12.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
1-Oct-2014
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
BQ24080DRCR
VSON
DRC
10
3000
367.0
367.0
35.0
BQ24080DRCT
VSON
DRC
10
250
210.0
185.0
35.0
BQ24081DRCR
VSON
DRC
10
3000
338.0
355.0
50.0
BQ24081DRCT
VSON
DRC
10
250
338.0
355.0
50.0
Pack Materials-Page 2
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated
Similar pages