AD ADV7125KSTZ140 Cmos, 330 mhz triple 8-bit high speed video dac Datasheet

CMOS, 330 MHz
Triple 8-Bit High Speed Video DAC
ADV7125
FEATURES
FUNCTIONAL BLOCK DIAGRAM
VAA
BLANK
BLANK AND
SYNC LOGIC
SYNC
R7 TO R0
8
DATA
REGISTER
8
DAC
G7 TO G0
8
DATA
REGISTER
8
DAC
B7 TO B0
8
DATA
REGISTER
8
DAC
PSAVE
IOG
IOB
IOB
VOLTAGE
REFERENCE
CIRCUIT
POWER-DOWN
MODE
VREF
ADV7125
GND
Digital video systems
High resolution color graphics
Digital radio modulation
Image processing
Instrumentation
Video signal reconstruction
Automotive infotainment units
IOR
IOG
CLOCK
APPLICATIONS
IOR
RSET COMP
03097-001
330 MSPS throughput rate
Triple 8-bit DACs
RS-343A-/RS-170-compatible output
Complementary outputs
DAC output current range: 2.0 mA to 26.5 mA
TTL-compatible inputs
Internal Reference (1.235 V)
Single-supply +5 V/+3.3 V operation
48-lead LQFP and LFCSP packages
Low power dissipation (30 mW minimum @ 3 V)
Low power standby mode (6 mW typical @ 3 V)
Industrial temperature range (−40°C to +85°C)
Pb-free (lead-free) packages
Qualified for automotive applications
Figure 1.
GENERAL DESCRIPTION
The ADV7125 (ADV®) is a triple high speed, digital-to-analog
converter on a single monolithic chip. It consists of three high
speed, 8-bit video DACs with complementary outputs, a
standard TTL input interface, and a high impedance, analog
output current source.
The ADV7125 is fabricated in a 5 V CMOS process. Its
monolithic CMOS construction ensures greater functionality
with lower power dissipation. The ADV7125 is available in
48-lead LQFP and 48-lead LFCSP packages.
The ADV7125 has three separate 8-bit-wide input ports. A
single +5 V/+3.3 V power supply and clock are all that are
required to make the part functional. The ADV7125 has
additional video control signals, composite SYNC and BLANK,
as well as a power save mode.
1.
2.
3.
PRODUCT HIGHLIGHTS
330 MSPS (3.3 V only) throughput.
Guaranteed monotonic to eight bits.
Compatible with a wide variety of high resolution color
graphics systems, including RS-343A and RS-170.
ADV is a registered trademark of Analog Devices, Inc.
Rev. C
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2002–2011 Analog Devices, Inc. All rights reserved.
ADV7125
TABLE OF CONTENTS
Features .............................................................................................. 1
Circuit Description and Operation.............................................. 11
Applications....................................................................................... 1
Digital Inputs .............................................................................. 11
Functional Block Diagram .............................................................. 1
Clock Input.................................................................................. 11
General Description ......................................................................... 1
Video Synchronization and Control........................................ 12
Product Highlights ........................................................................... 1
Reference Input........................................................................... 12
Revision History ............................................................................... 2
DACs ............................................................................................ 12
Specifications..................................................................................... 3
Analog Outputs .......................................................................... 12
5 V Electrical Characteristics...................................................... 3
Gray Scale Operation................................................................. 13
3.3 V Electrical Characteristics................................................... 4
Video Output Buffers................................................................. 13
5 V Timing Specifications ........................................................... 5
PCB Layout Considerations...................................................... 13
3.3 V Timing Specifications ........................................................ 6
Digital Signal Interconnect ....................................................... 13
Absolute Maximum Ratings............................................................ 7
Analog Signal Interconnect....................................................... 14
ESD Caution.................................................................................. 7
Outline Dimensions ....................................................................... 15
Pin Configuration and Function Descriptions............................. 8
Ordering Guide .......................................................................... 16
Terminology .................................................................................... 10
Automotive Products ................................................................. 16
REVISION HISTORY
2/11—Rev. B to Rev. C
Change to Table 6 ............................................................................. 8
7/10—Rev. A to Rev. B
Change to Features Section ............................................................. 1
Changes to Clock Frequency Parameter, Table 4 ......................... 6
Changes to Figure 2.......................................................................... 6
Changes to Figure 4 and Figure 5................................................. 11
Changes to Table 7.......................................................................... 12
Changes to Endnotes to Ordering Guide .................................... 15
Added Automotive Products Section .......................................... 15
3/09—Rev. 0 to Rev. A
Updated Format..................................................................Universal
Changes to Features Section, Applications Section, and General
Description Section .......................................................................... 1
Changes to Figure 3 and Table 6......................................................8
Deleted Ground Planes Section, Power Planes Section, and
Supply Decoupling Section ........................................................... 11
Changes to Figure 5........................................................................ 11
Changes to Table 7, Analog Outputs Section, Figure 6, and
Figure 7 ............................................................................................ 12
Changes to Video Output Buffers Section, PCB Layout
Considerations Section, and Figure 9 .......................................... 13
Changes to Analog Signal Interconnect Section and
Figure 10 .......................................................................................... 14
Updated Outline Dimensions....................................................... 15
Changes to Ordering Guide .......................................................... 16
10/02—Revision 0: Initial Version
Rev. C | Page 2 of 16
ADV7125
SPECIFICATIONS
5 V ELECTRICAL CHARACTERISTICS
VAA = 5 V ± 5%, VREF = 1.235 V, RSET = 560 Ω, CL = 10 pF. All specifications TMIN to TMAX, 1 unless otherwise noted, TJ MAX = 110°C.
Table 1.
Parameter
STATIC PERFORMANCE
Resolution (Each DAC)
Integral Nonlinearity (BSL)
Differential Nonlinearity
DIGITAL AND CONTROL INPUTS
Input High Voltage, VIH
Input Low Voltage, VIL
Input Current, IIN
PSAVE Pull-Up Current
Min
Typ
Max
Unit
Test Conditions1
8
−1
−1
±0.4
±0.25
+1
+1
Bits
LSB
LSB
Guaranteed Monotonic
2
−1
20
10
Input Capacitance, CIN
ANALOG OUTPUTS
Output Current
DAC-to-DAC Matching
Output Compliance Range, VOC
Output Impedance, ROUT
Output Capacitance, COUT
Offset Error
Gain Error 2
VOLTAGE REFERENCE, EXTERNAL AND
INTERNAL
Reference Range, VREF
POWER DISSIPATION
Digital Supply Current 3
Analog Supply Current
Standby Supply Current 4
Power Supply Rejection Ratio
0.8
+1
2.0
2.0
+0.025
+5.0
mA
mA
%
V
kΩ
pF
% FSR
% FSR
1.235
1.35
V
3.4
10.5
18
67
8
2.1
0.1
9
15
25
72
mA
mA
mA
mA
mA
mA
%/%
1.0
0
26.5
18.5
5
1.4
100
10
−0.025
−5.0
1.12
V
V
μA
μA
pF
5.0
0.5
1
VIN = 0.0 V or VDD
Green DAC, SYNC = high
RGB DAC, SYNC = low
IOUT = 0 mA
Tested with DAC output = 0 V
FSR = 18.62 mA
fCLK = 50 MHz
fCLK = 140 MHz
fCLK = 240 MHz
RSET = 530 Ω
RSET = 4933 Ω
PSAVE = low, digital, and control inputs at VDD
Temperature range TMIN to TMAX: −40°C to +85°C at 50 MHz and 140 MHz, 0°C to +70°C at 240 MHz and 330 MHz.
Gain error = ((Measured (FSC)/Ideal (FSC) − 1) × 100), where Ideal = VREF/RSET × K × (0xFFH) × 4 and K = 7.9896.
Digital supply is measured with a continuous clock that has data input corresponding to a ramp pattern and with an input level at 0 V and VDD.
4
These maximum/minimum specifications are guaranteed by characterization in the 4.75 V to 5.25 V range.
2
3
Rev. C | Page 3 of 16
ADV7125
3.3 V ELECTRICAL CHARACTERISTICS
VAA = 3.0 V to 3.6 V, VREF = 1.235 V, RSET = 560 Ω, CL = 10 pF. All specifications TMIN to TMAX, 1 unless otherwise noted, TJ MAX = 110°C.
Table 2.
Parameter 2
STATIC PERFORMANCE
Resolution (Each DAC)
Integral Nonlinearity (BSL)
Differential Nonlinearity
DIGITAL AND CONTROL INPUTS
Input High Voltage, VIH
Input Low Voltage, VIL
Input Current, IIN
PSAVE Pull-Up Current
Input Capacitance, CIN
ANALOG OUTPUTS
Output Current
DAC-to-DAC Matching
Output Compliance Range, VOC
Output Impedance, ROUT
Output Capacitance, COUT
Offset Error
Gain Error 3
VOLTAGE REFERENCE, EXTERNAL
Reference Range, VREF
VOLTAGE REFERENCE, INTERNAL
Voltage Reference, VREF
POWER DISSIPATION
Digital Supply Current 4
Analog Supply Current
Standby Supply Current
Power Supply Rejection Ratio
Min
Typ
Max
Unit
Test Conditions1
−1
−1
±0.5
±0.25
8
+1
+1
Bits
LSB
LSB
RSET = 680 Ω
RSET = 680 Ω
RSET = 680 Ω
+1
V
V
μA
μA
pF
VIN = 0.0 V or VDD
2.0
0.8
−1
20
10
2.0
2.0
26.5
18.5
1.0
0
1.4
70
10
0
0
1.12
1.235
0
1.35
1.235
2.2
6.5
11
16
67
8
2.1
0.1
mA
mA
%
V
kΩ
pF
% FSR
% FSR
Green DAC, SYNC = high
RGB DAC, SYNC = low
Tested with DAC output = 0 V
FSR = 18.62 mA
V
V
5.0
12.0
15
72
5.0
0.5
mA
mA
mA
mA
mA
mA
mA
%/%
1
fCLK = 50 MHz
fCLK = 140 MHz
fCLK = 240 MHz
fCLK = 330 MHz
RSET = 560 Ω
RSET = 4933 Ω
PSAVE = low, digital, and control inputs at VDD
Temperature range TMIN to TMAX: −40°C to +85°C at 50 MHz and 140 MHz, 0°C to +70°C at 240 MHz and 330 MHz.
These max/min specifications are guaranteed by characterization in the 3.0 V to 3.6 V range.
Gain error = ((Measured (FSC)/Ideal (FSC) −1) × 100), where Ideal = VREF/RSET × K × (0xFFH) × 4 and K = 7.9896.
4
Digital supply is measured with continuous clock that has data input corresponding to a ramp pattern and with an input level at 0 V and VDD.
2
3
Rev. C | Page 4 of 16
ADV7125
5 V TIMING SPECIFICATIONS
VAA = 5 V ± 5%, 1 VREF = 1.235 V, RSET = 560 Ω, CL = 10 pF. All specifications TMIN to TMAX, 2 unless otherwise noted, TJ MAX = 110°C.
Table 3.
Parameter 3
ANALOG OUTPUTS
Analog Output Delay
Analog Output Rise/Fall Time 4
Analog Output Transition Time 5
Analog Output Skew 6
CLOCK CONTROL
CLOCK Frequency 7
Data and Control Setup6
Data and Control Hold6
CLOCK Period
CLOCK Pulse Width High6
CLOCK Pulse Width Low6
CLOCK Pulse Width High6
CLOCK Pulse Width Low6
CLOCK Pulse Width High
CLOCK Pulse Width Low
Pipeline Delay6
PSAVE Up Time6
Symbol
Min
t6
t7
t8
t9
fCLK
t1
t2
t3
t4
t5
t4
t5
t4
t5
tPD
t10
Typ
5.5
1.0
15
1
0.5
0.5
0.5
0.5
1.5
4.17
1.875
1.875
2.85
2.85
8.0
8.0
1.0
Max
Unit
2
ns
ns
ns
ns
50
140
240
1.0
2
1
1.0
10
MHz
MHz
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
Clock cycles
ns
Conditions
50 MHz grade
140 MHz grade
240 MHz grade
fCLK_MAX = 240 MHz
fCLK_MAX = 240 MHz
fCLK_MAX = 140 MHz
fCLK_MAX = 140 MHz
fCLK_MAX = 50 MHz
fCLK_MAX = 50 MHz
The maximum and minimum specifications are guaranteed over this range.
Temperature range TMIN to TMAX: −40°C to +85°C at 50 MHz and 140 MHz, 0°C to +70°C at 240 MHz.
3
Timing specifications are measured with input levels of 3.0 V (VIH) and 0 V (VIL) for both 5 V and 3.3 V supplies.
4
Rise time was measured from the 10% to 90% point of zero to full-scale transition, fall time from the 90% to 10% point of a full-scale transition.
5
Measured from 50% point of full-scale transition to 2% of final value.
6
Guaranteed by characterization.
7
fCLK maximum specification production tested at 125 MHz and 5 V. Limits specified here are guaranteed by characterization.
2
Rev. C | Page 5 of 16
ADV7125
3.3 V TIMING SPECIFICATIONS
VAA = 3.0 V to 3.6 V, 1 VREF = 1.235 V, RSET = 560 Ω, CL = 10 pF. All specifications TMIN to TMAX, 2 unless otherwise noted, TJ MAX = 110°C.
Table 4.
Parameter 3
ANALOG OUTPUTS
Analog Output Delay,
Analog Output Rise/Fall Time 4
Analog Output Transition Time 5
Analog Output Skew 6
CLOCK CONTROL
CLOCK Frequency 7
Data and Control Setup6
Data and Control Hold6
CLOCK Period
CLOCK Pulse Width High6
CLOCK Pulse Width Low6
CLOCK Pulse Width High6
CLOCK Pulse Width Low6
CLOCK Pulse Width High6
CLOCK Pulse Width Low6
CLOCK Pulse Width High
CLOCK Pulse Width Low
Pipeline Delay6
PSAVE Up Time6
Symbol
Min
Typ
t6
t7
t8
t9
7.5
1.0
15
1
fCLK
Max
Unit
2
ns
ns
ns
ns
50
140
240
330
t1
t2
t3
t4
t5
t4
t5
t4
t5
t4
t5
tPD
t10
0.2
1.5
3
1.4
1.4
1.875
1.875
2.85
2.85
8.0
8.0
1.0
1.0
4
MHz
MHz
MHz
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Clock cycles
ns
1.0
10
Conditions
50 MHz grade
140 MHz grade
240 MHz grade
330 MHz grade
fCLK_MAX = 330 MHz
fCLK_MAX = 330 MHz
fCLK_MAX = 240 MHz
fCLK_MAX = 240 MHz
fCLK_MAX = 140 MHz
fCLK_MAX = 140 MHz
fCLK_MAX = 50 MHz
fCLK_MAX = 50 MHz
1
These maximum and minimum specifications are guaranteed over this range.
Temperature range: TMIN to TMAX: −40°C to +85°C at 50 MHz and 140 MHz, 0°C to +70°C at 240 MHz and 330 MHz.
3
Timing specifications are measured with input levels of 3.0 V (VIH) and 0 V (VIL) for 3.3 V supplies.
4
Rise time was measured from the 10% to 90% point of zero to full-scale transition, fall time from the 90% to 10% point of a full-scale transition.
5
Measured from 50% point of full-scale transition to 2% of final value.
6
Guaranteed by characterization.
7
fCLK maximum specification production tested at 125 MHz and 5 V. Limits specified here are guaranteed by characterization.
2
t3
t4
t5
CLOCK
t2
DIGITAL INPUTS
(R7 TO R0, G7 TO G0, B7 TO B0,
SYNC, BLANK)
t1
ANALOG OUTPUTS
(IOR, IOR, IOG, IOG, IOB, IOB)
t6
t8
NOTES
1. OUTPUT DELAY (t6) MEASURED FROM THE 50% POINT OF THE RISING EDGE OF CLOCK TO THE 50% POINT
OF FULL-SCALE TRANSITION.
2. OUTPUT RISE/FALL TIME (t7) MEASURED BETWEEN THE 10% AND 90% POINTS OF FULL-SCALE TRANSITION.
3. TRANSITION TIME (t8) MEASURED FROM THE 50% POINT OF FULL-SCALE TRANSITION TO WITHIN 2% OF THE
FINAL OUTPUT VALUE.
Figure 2. Timing Diagram
Rev. C | Page 6 of 16
03097-002
t7
ADV7125
ABSOLUTE MAXIMUM RATINGS
Table 5.
Parameter
VAA to GND
Voltage on Any Digital Pin
Ambient Operating Temperature (TA)
Storage Temperature (TS)
Junction Temperature (TJ)
Lead Temperature (Soldering, 10 sec)
Vapor Phase Soldering (1 Minute)
IOUT to GND1
1
Rating
7V
GND − 0.5 V to VAA + 0.5 V
−40°C to +85°C
−65°C to +150°C
150°C
300°C
220°C
0 V to VAA
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
Analog output short circuit to any power supply or common GND can be of
an indefinite duration.
Rev. C | Page 7 of 16
ADV7125
48
47
46
45
44
43
42
41
40
39
38
37
R7
R6
R5
R4
R3
R2
R1
R0
GND
GND
PSAVE
RSET
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
ADV7125
TOP VIEW
(Not to Scale)
36
35
34
33
32
31
30
29
28
27
26
25
VREF
COMP
IOR
IOR
IOG
IOG
VAA
VAA
IOB
IOB
GND
GND
VAA
GND
GND
B0
B1
B2
B3
B4
B5
B6
B7
CLOCK
13
14
15
16
17
18
19
20
21
22
23
24
G0 3
G1 4
G2 5
G3 6
G4 7
G5 8
G6 9
G7 10
BLANK 11
SYNC 12
PIN 1
INDICATOR
03097-003
GND
GND
NOTES
1. THE LFCSP_VQ HAS AN EXPOSED PADDLE THAT MUST BE
CONNECTED TO GND.
Figure 3. Pin Configuration
Table 6. Pin Function Descriptions
Pin Number
1, 2, 14, 15, 25,
26, 39, 40
3 to 10, 16 to
23, 41 to 48
Mnemonic
GND
Description
Ground. All GND pins must be connected.
11
G0 to G7,
B0 to B7,
R0 to R7
BLANK
12
SYNC
13, 29, 30
24
VAA
CLOCK
33, 31, 27
IOR, IOG, IOB
34, 32, 28
IOR, IOG, IOB
35
COMP
36
VREF
Red, Green, and Blue Pixel Data Inputs (TTL Compatible). Pixel data is latched on the rising edge of
CLOCK. R0, G0, and B0 are the least significant data bits. Unused pixel data inputs should be
connected to either the regular printed circuit board (PCB) power or ground plane.
Composite Blank Control Input (TTL Compatible). A Logic 0 on this control input drives the analog
outputs, IOR, IOB, and IOG, to the blanking level. The BLANK signal is latched on the rising edge of
CLOCK. While BLANK is a Logic 0, the R0 to R7, G0 to G7, and B0 to B7 pixel inputs are ignored.
Composite Sync Control Input (TTL Compatible). A Logic 0 on the SYNC input switches off a
40 IRE current source. This is internally connected to the IOG analog output. SYNC does not override
any other control or data input; therefore, it should only be asserted during the blanking interval.
SYNC is latched on the rising edge of CLOCK. If sync information is not required on the green channel,
the SYNC input should be tied to Logic 0.
Analog Power Supply (5 V ± 5%). All VAA pins on the ADV7125 must be connected.
Clock Input (TTL Compatible). The rising edge of CLOCK latches the R0 to R7, G0 to G7, B0 to B7, SYNC,
and BLANK pixel and control inputs. It is typically the pixel clock rate of the video system. CLOCK
should be driven by a dedicated TTL buffer.
Differential Red, Green, and Blue Current Outputs (High Impedance Current Sources). These RGB video
outputs are specified to directly drive RS-343A and RS-170 video levels into a doubly terminated 75 Ω
load. If the complementary outputs are not required, these outputs should be tied to ground.
Red, Green, and Blue Current Outputs. These high impedance current sources are capable of directly
driving a doubly terminated 75 Ω coaxial cable. All three current outputs should have similar output
loads whether or not they are all being used.
Compensation Pin. This is a compensation pin for the internal reference amplifier. A 0.1 μF ceramic
capacitor must be connected between COMP and VAA.
Voltage Reference Input for DACs or Voltage Reference Output (1.235 V).
Rev. C | Page 8 of 16
ADV7125
Pin Number
37
Mnemonic
RSET
38
PSAVE
49 (EPAD)
EP (EPAD)
Description
A resistor (RSET) connected between this pin and GND controls the magnitude of the full-scale video
signal. Note that the IRE relationships are maintained, regardless of the full-scale output current. The
relationship between RSET and the full-scale output current on IOG (assuming ISYNC is connected to IOG)
is given by:
RSET (Ω) = 11,445 × VREF (V)/IOG (mA)
The relationship between RSET and the full-scale output current on IOR, IOG, and IOB is given by:
IOG (mA) = 11,444.8 × VREF (V)/RSET (Ω) (SYNC being asserted)
IOR, IOB (mA) = 7989.6 × VREF (V)/RSET (Ω)
The equation for IOG is the same as that for IOR and IOB when SYNC is not being used, that is, SYNC
tied permanently low.
Power Save Control Pin. Reduced power consumption is available on the ADV7125 when this pin is
active.
The LFCSP_VQ has an exposed paddle that must be connected to GND.
Rev. C | Page 9 of 16
ADV7125
TERMINOLOGY
Blanking Level
The level separating the SYNC portion from the video portion
of the waveform. Usually referred to as the front porch or back
porch. At 0 IRE units, it is the level that shuts off the picture
tube, resulting in the blackest possible picture.
Raster Scan
The most basic method of sweeping a CRT one line at a time to
generate and display images.
Color Video (RGB)
This refers to the technique of combining the three primary
colors of red, green, and blue to produce color pictures within
the usual spectrum. In RGB monitors, three DACs are required,
one for each color.
Reference White Level
The maximum positive polarity amplitude of the video signal.
Sync Signal (SYNC)
The position of the composite video signal that synchronizes
the scanning process.
Gray Scale
The discrete levels of video signal between reference black and
reference white levels. An 8-bit DAC contains 256 different levels.
Reference Black Level
The maximum negative polarity amplitude of the video signal.
Sync Level
The peak level of the SYNC signal.
Video Signal
The portion of the composite video signal that varies in gray
scale levels between reference white and reference black. Also
referred to as the picture signal, this is the portion that can be
visually observed.
Rev. C | Page 10 of 16
ADV7125
CIRCUIT DESCRIPTION AND OPERATION
The ADV7125 contains three 8-bit DACs, with three input
channels, each containing an 8-bit register. Also integrated
on board the part is a reference amplifier. The CRT control
functions, BLANK and SYNC, are integrated on board the
ADV7125.
Table 7 details the resultant effect on the analog outputs of
BLANK and SYNC.
DIGITAL INPUTS
The CLOCK input of the ADV7125 is typically the pixel clock
rate of the system. It is also known as the dot rate. The dot rate,
and thus the required CLOCK frequency, is determined by the
on-screen resolution, according to the following equation:
All these digital inputs are specified to accept TTL logic levels.
CLOCK INPUT
There are 24 bits of pixel data (color information), R0 to R7,
G0 to G7, and B0 to B7, latched into the device on the rising
edge of each clock cycle. This data is presented to the three 8-bit
DACs and then converted to three analog (RGB) output waveforms (see Figure 4).
CLOCK
DIGITAL INPUTS
(R7 TO R0, G7 TO G0,
B7 TO B0,
SYNC, BLANK)
DATA
03097-004
ANALOG OUTPUTS
(IOR, IOR, IOG, IOG,
IOB, IOB)
Figure 4. Video Data Input/Output
The ADV7125 has two additional control signals that are latched
to the analog video outputs in a similar fashion. BLANK and
SYNC are each latched on the rising edge of CLOCK to maintain
synchronization with the pixel data stream.
The BLANK and SYNC functions allow for the encoding of
these video synchronization signals onto the RGB video output.
This is done by adding appropriately weighted current sources
to the analog outputs, as determined by the logic levels on the
BLANK and SYNC digital inputs.
Dot Rate = (Horiz Res) × (Vert Res) × (Refresh
Rate)/(Retrace Factor)
where:
Horiz Res is the number of pixels per line.
Vert Res is the number of lines per frame.
Refresh Rate is the horizontal scan rate. This is the rate at which
the screen must be refreshed, typically 60 Hz for a noninterlaced
system, or 30 Hz for an interlaced system.
Retrace Factor is the total blank time factor. This takes into
account that the display is blanked for a certain fraction of the
total duration of each frame (for example, 0.8).
Therefore, for a graphics system with a 1024 × 1024 resolution,
a noninterlaced 60 Hz refresh rate, and a retrace factor of 0.8,
Dot Rate = 1024 × 1024 × 60/0.8 = 78.6 MHz
The required CLOCK frequency is thus 78.6 MHz. All video
data and control inputs are latched into the ADV7125 on the
rising edge of CLOCK, as previously described in the Digital
Inputs section. It is recommended that the CLOCK input to the
ADV7125 be driven by a TTL buffer (for example, the 74F244).
Figure 5 shows the analog output, RGB video waveform of the
ADV7125. The influence of SYNC and BLANK on the analog
video waveform is illustrated.
RED AND BLUE
GREEN
V
mA
V
18.67
0.7
26.0
0.975
0
0
WHITE LEVEL
7.2
0.271
BLANK LEVEL
0
0
SYNC LEVEL
NOTES
1. OUTPUTS CONNECTED TO A DOUBLY TERMINATED 75Ω LOAD.
2. VREF = 1.235V, RSET = 530Ω.
3. RS-343 LEVELS AND TOLERANCES ASSUMED ON ALL LEVELS.
Figure 5. Typical RGB Video Output Waveform
Rev. C | Page 11 of 16
03097-005
mA
ADV7125
Table 7. Typical Video Output Truth Table (RSET = 530 Ω, RLOAD = 37.5 Ω)
IOG (mA)
0
18.67 − Video
18.67 − Video
18.67
18.67
18.67
18.67
IOR/IOB (mA)
18.67
Video
Video
0
0
0
0
VIDEO SYNCHRONIZATION AND CONTROL
The ADV7125 has a single composite sync (SYNC) input
control. Many graphics processors and CRT controllers have the
ability to generate horizontal sync (HSYNC), vertical sync
(VSYNC), and composite SYNC.
In a graphics system that does not automatically generate a
composite SYNC signal, the inclusion of some additional logic
circuitry enables the generation of a composite SYNC signal.
The sync current is internally connected directly to the IOG
output, thus encoding video synchronization information onto
the green video channel. If it is not required to encode sync
information onto the ADV7125, the SYNC input should be tied
to logic low.
REFERENCE INPUT
The ADV7125 contains an on-board voltage reference. The VREF
pin should be connected as shown in Figure 10.
A resistance, RSET, connected between the RSET pin and GND,
determines the amplitude of the output video level according to
Equation 1 and Equation 2 for the ADV7125.
IOG (mA) = 11,444.8 × VREF (V)/RSET (Ω)
(1)
IOR, IOB (mA) = 7989.6 × VREF (V)/RSET (Ω)
(2)
Equation 1 applies to the ADV7125 only, when SYNC is being
used. If SYNC is not being encoded onto the green channel,
Equation 1 is similar to Equation 2.
IOR/IOB (mA)
SYNC
BLANK
0
18.67 − Video
18.67 − Video
18.67
18.67
18.67
18.67
1
1
0
1
0
1
0
1
1
1
1
1
0
0
DAC Input Data
0xFFH
Data
Data
0x00H
0x00H
0xXXH (don’t care)
0xXXH (don’t care)
low glitch. The on-board operational amplifier stabilizes the
full-scale output current against temperature and power supply
variations.
ANALOG OUTPUTS
The ADV7125 has three analog outputs, corresponding to the
red, green, and blue video signals.
The red, green, and blue analog outputs of the ADV7125 are
high impedance current sources. Each one of these three RGB
current outputs is capable of directly driving a 37.5 Ω load, such
as a doubly terminated 75 Ω coaxial cable. Figure 6 shows the
required configuration for each of the three RGB outputs
connected into a doubly terminated 75 Ω load. This arrangement
develops RS-343A video output voltage levels across a 75 Ω
monitor.
A suggested method of driving RS-170 video levels into a 75 Ω
monitor is shown in Figure 7. The output current levels of the
DACs remain unchanged, but the source termination resistance,
ZS, on each of the three DACs is increased from 75 Ω to 150 Ω.
IOR, IOG, IOB
Z0 = 75Ω
DACs
ZS = 75Ω
(SOURCE
TERMINATION)
(CABLE)
ZL = 75Ω
(MONITOR)
03097-006
IOG (mA)
26.0
Video + 7.2
Video
7.2
0
7.2
0
TERMINATION REPEATED THREE TIMES
FOR RED, GREEN, AND BLUE DACs
Figure 6. Analog Output Termination for RS-343A
Using a variable value of RSET allows for accurate adjustment of
the analog output video levels. Use of a fixed 560 Ω RSET resistor
yields the analog output levels quoted in the Specifications section.
These values typically correspond to the RS-343A video waveform values, as shown in Figure 5.
IOR, IOG, IOB
Z0 = 75Ω
DACs
ZS = 150Ω
(SOURCE
TERMINATION)
(CABLE)
ZL = 75Ω
(MONITOR)
DACS
The ADV7125 contains three matched 8-bit DACs. The DACs
are designed using an advanced, high speed, segmented architecture. The bit currents corresponding to each digital input are
routed to either the analog output (bit = 1) or GND (bit = 0)
by a sophisticated decoding scheme. Because all this circuitry
is on one monolithic device, matching between the three DACs
is optimized. As well as matching, the use of identical current
sources in a monolithic design guarantees monotonicity and
TERMINATION REPEATED THREE TIMES
FOR RED, GREEN, AND BLUE DACs
03097-007
Video Output Level
White Level
Video
Video to BLANK
Black Level
Black to BLANK
BLANK Level
SYNC Level
Figure 7. Analog Output Termination for RS-170
More detailed information regarding load terminations for
various output configurations, including RS-343A and RS-170,
is available in the AN-205 Application Note, Video Formats and
Required Load Terminations, available from Analog Devices at
www.analog.com.
Rev. C | Page 12 of 16
ADV7125
Z1
Z2
+VS
IOR, IOG, IOB
DACs
ZS = 75Ω
(SOURCE
TERMINATION)
2
4
AD848
3
0.1µF
6
7
0.1µF
75Ω
Z0 = 75Ω
(CABLE)
ZL = 75Ω
(MONITOR)
–VS
GAIN (G) = 1 +
Z1
Z2
03097-009
Figure 5 shows the video waveforms associated with the three
RGB outputs driving the doubly terminated 75 Ω load of
Figure 6. As well as the gray scale levels (black level to white
level), Figure 5 also shows the contributions of SYNC and
BLANK for the ADV7125. These control inputs add appropriately weighted currents to the analog outputs, producing
the specific output level requirements for video applications.
Table 7 details how the SYNC and BLANK inputs modify the
output levels.
Figure 9. AD848 As an Output Buffer
GRAY SCALE OPERATION
PCB LAYOUT CONSIDERATIONS
The ADV7125 can be used for standalone, gray scale (monochrome) or composite video applications (that is, only one channel
used for video information). Any one of the three channels, red,
green, or blue, can be used to input the digital video data. The
two unused video data channels should be tied to Logic 0. The
unused analog outputs should be terminated with the same load
as that for the used channel, that is, if the red channel is used
and IOR is terminated with a doubly terminated 75 Ω load
(37.5 Ω), IOB and IOG should be terminated with 37.5 Ω
resistors (see Figure 8).
The ADV7125 is optimally designed for lowest noise performance, both radiated and conducted noise. To complement the
excellent noise performance of the ADV7125, it is imperative
that great care be given to the PCB layout. Figure 10 shows a
recommended connection diagram for the ADV7125.
VIDEO
OUTPUT
R0
IOR
R7
IOG
ADV7125
DOUBLY
TERMINATED
75Ω LOAD
37.5Ω
G0
G7
IOB
37.5Ω
B7
GND
03097-008
B0
Figure 8. Input and Output Connections for Standalone Gray Scale or
Composite Video
VIDEO OUTPUT BUFFERS
The ADV7125 is specified to drive transmission line loads. The
analog output configuration to drive such loads is described in the
Analog Outputs section and illustrated in Figure 9. However,
in some applications, it may be required to drive long transmission line cable lengths. Cable lengths greater than 10 meters can
attenuate and distort high frequency analog output pulses. The
inclusion of output buffers compensates for some cable distortion.
Buffers with large full power bandwidths and gains between
two and four are required. These buffers also need to be able
to supply sufficient current over the complete output voltage
swing. Analog Devices produces a range of suitable op amps for
such applications. These include the AD843, AD844, AD847,
and AD848 series of monolithic op amps. In very high frequency
applications (80 MHz), the AD8061 is recommended. More
information on line driver buffering circuits is given in the
relevant op amp data sheets.
Use of buffer amplifiers also allows implementation of other
video standards besides RS-343A and RS-170. Altering the gain
components of the buffer circuit results in any desired video level.
The layout should be optimized for lowest noise on the
ADV7125 power and ground lines. This can be achieved by
shielding the digital inputs and providing good decoupling.
Shorten the lead length between groups of VAA and GND pins
to minimize inductive ringing.
It is recommended to use a 4-layer printed circuit board with a
single ground plane. The ground and power planes should
separate the signal trace layer and the solder side layer. Noise
on the analog power plane can be further reduced by using
multiple decoupling capacitors (see Figure 10). Optimum
performance is achieved by using 0.1 μF and 0.01 μF ceramic
capacitors. Individually decouple each VAA pin to ground by
placing the capacitors as close as possible to the device with the
capacitor leads as short as possible, thus minimizing lead
inductance. It is important to note that while the ADV7125
contains circuitry to reject power supply noise, this rejection
decreases with frequency. If a high frequency switching power
supply is used, pay close attention to reducing power supply
noise. A dc power supply filter (Murata BNX002) provides EMI
suppression between the switching power supply and the main
PCB. Alternatively, consideration can be given to using a 3terminal voltage regulator.
DIGITAL SIGNAL INTERCONNECT
Isolate the digital signal lines to the ADV7125 as much as
possible from the analog outputs and other analog circuitry.
Digital signal lines should not overlay the analog power plane.
Due to the high clock rates used, long clock lines to the
ADV7125 should be avoided to minimize noise pickup.
Connect any active pull-up termination resistors for the digital
inputs to the regular PCB power plane (VCC) and not to the
analog power plane.
Rev. C | Page 13 of 16
ADV7125
For optimum performance, the analog outputs should each
have a source termination resistance to ground of 75 Ω (doubly
terminated 75 Ω configuration). This termination resistance
should be as close as possible to the ADV7125 to minimize
reflections.
ANALOG SIGNAL INTERCONNECT
Place the ADV7125 as close as possible to the output connectors,
thus minimizing noise pickup and reflections due to impedance
mismatch.
The video output signals should overlay the ground plane and
not the analog power plane, thereby maximizing the high
frequency power supply rejection.
Additional information on PCB design is available in the
AN-333 Application Note, Design and Layout of a Video
Graphics System for Reduced EMI, which is available from
Analog Devices at www.analog.com.
POWER SUPPLY DECOUPLING
(0.1µF AND 0.01µF CAPACITOR
FOR EACH VAA GROUP)
0.1µF
0.1µF
VAA
35 COMP
VAA
0.01µF
13, 29,
30
VAA
41 TO 48
1kΩ
VREF 36
R7 TO R0
1
AD1580
3 TO 10
G7 TO G0
1µF
2
RSET
530Ω
MONITOR (CRT)
COAXIAL CABLE
75Ω
IOR 34
16 TO 23
75Ω
B7 TO B0
IOG 32
75Ω
ADV7125
IOB 28
75Ω
12 SYNC
75Ω
BNC
CONNECTORS
IOR 33
11 BLANK
IOG 31
24 CLOCK
75Ω
75Ω
COMPLEMENTARY
OUTPUTS
IOB 27
38 PSAVE
GND
03097-010
VIDEO
DATA
INPUTS
RSET 37
VAA
1, 2, 14, 15,
25, 26, 39, 40
Figure 10. Typical Connection Diagram
Rev. C | Page 14 of 16
ADV7125
OUTLINE DIMENSIONS
0.75
0.60
0.45
9.20
9.00 SQ
8.80
1.60
MAX
37
48
36
1
PIN 1
7.20
7.00 SQ
6.80
TOP VIEW
1.45
1.40
1.35
0.15
0.05
0.20
0.09
7°
3.5°
0°
0.08
COPLANARITY
SEATING
PLANE
(PINS DOWN)
25
12
13
24
0.27
0.22
0.17
VIEW A
0.50
BSC
LEAD PITCH
VIEW A
051706-A
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026-BBC
Figure 11. 48-Lead Low Profile Quad Flat Package [LQFP]
(ST-48)
Dimensions shown in millimeters
7.00
BSC SQ
0.60 MAX
37
36
PIN 1
INDICATOR
1
5.25
5.10 SQ
4.95
(BOTTOM VIEW)
25
24
13
12
0.25 MIN
5.50
REF
0.80 MAX
0.65 TYP
0.50 BSC
SEATING
PLANE
PIN 1
INDICATOR
EXPOSED
PAD
6.75
BSC SQ
0.50
0.40
0.30
12° MAX
48
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-VKKD-2
Figure 12. 48-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
7 mm × 7 mm Body, Very Thin Quad
(CP-48-1)
Dimensions shown in millimeters
Rev. C | Page 15 of 16
080108-A
TOP
VIEW
1.00
0.85
0.80
0.30
0.23
0.18
0.60 MAX
ADV7125
ORDERING GUIDE
Model 1, 2, 3
ADV7125KSTZ50
ADV7125KSTZ50-REEL
ADV7125KSTZ140
ADV7125JSTZ240
ADV7125JSTZ330
ADV7125WBSTZ170
ADV7125WBSTZ170-RL
ADV7125BCPZ170
ADV7125BCPZ170-RL
ADV7125WBCPZ170
ADV7125WBCPZ170-RL
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
0°C to +70°C
0°C to +70°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
48-Lead LQFP
48-Lead LQFP
48-Lead LQFP
48-Lead LQFP
48-Lead LQFP
48-Lead LQFP
48-Lead LQFP
48-Lead LFCSP_VQ
48-Lead LFCSP_VQ
48-Lead LFCSP_VQ
48-Lead LFCSP_VQ
Speed Option
50 MHz
50 MHz
140 MHz
240 MHz
330 MHz
170 MHz
170 MHz
170 MHz
170 MHz
170 MHz
170 MHz
Package Option
ST-48
ST-48
ST-48
ST-48
ST-48
ST-48
ST-48
CP-48-1
CP-48-1
CP-48-1
CP-48-1
1
Z = RoHS Compliant Part.
W = Qualified for Automotive Applications.
3
ADV7125JSTZ330 is available in a 3.3 V option only.
2
AUTOMOTIVE PRODUCTS
The ADV7125W models are available with controlled manufacturing to support the quality and reliability requirements of automotive
applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers
should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in
automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to
obtain the specific Automotive Reliability reports for these models.
©2002–2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D03097-0-2/11(C)
Rev. C | Page 16 of 16
Similar pages