MIC5200 100 mA Low-Dropout Regulator Features General Description • • • • • • • • • • • The MIC5200 is an efficient linear voltage regulator with very low dropout voltage (typically 17 mV at light loads and 200 mV at 100 mA), and very low ground current (1 mA at 100 mA output), offering better than 1% initial accuracy with a logic-compatible ON/OFF switching input. Designed especially for hand-held battery-powered devices, the MIC5200 is switched by a CMOS- or TTL-compatible logic signal. The ENABLE control may be tied directly to VIN if unneeded. When disabled, power consumption drops nearly to zero. The ground current of the MIC5200 increases only slightly in dropout, further prolonging battery life. Key MIC5200 features include protection against reversed battery, current limiting, and overtemperature shutdown. High Output Voltage Accuracy Variety of Output Voltages Guaranteed 100 mA Output Low Quiescent Current Low Dropout Voltage Extremely Tight Load and Line Regulation Very Low Temperature Coefficient Current and Thermal Limiting Zero OFF Mode Current Logic-Controlled Electronic Shutdown Available in 8-Lead SOIC, MM8 8-Lead MSOP, and SOT-223 Packages Applications • • • • • • • Cellular Telephones Laptop, Notebook, and Palmtop Computers Battery-Powered Equipment PCMCIA VCC and VPP Regulation/Switching Barcode Scanners SMPS Post-Regulator/DC-to-DC Modules High Efficiency Linear Power Supplies The MIC5200 is available in several fixed voltages and accuracy configurations. Other options are available; contact Microchip for details. Typical Application Schematic MIC5200-3.3 OUTPUT 1μF ENABLE 2016 Microchip Technology Inc. DS20005578A-page 1 MIC5200 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings † Input Supply Voltage ................................................................................................................................... –20V to +60V Enable Input Voltage ................................................................................................................................... –20V to +60V Power Dissipation...................................................................................................................................Internally Limited Operating Ratings ‡ Input Voltage .............................................................................................................................................. +2.5V to +26V Enable Input Voltage ...................................................................................................................................... –20V to VIN † Notice: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational sections of this specification is not intended. Exposure to maximum rating conditions for extended periods may affect device reliability. ‡ Notice: The device is not guaranteed to function outside its operating ratings. DS20005578A-page 2 2016 Microchip Technology Inc. MIC5200 TABLE 1-1: ELECTRICAL CHARACTERISTICS Electrical Characteristics: Limits in standard typeface are for TJ = 25°C and limits in boldface apply over the junction temperature range of –40°C to +125°C. Unless otherwise specified, VIN = VOUT + 1V, IL = 1 mA, CL = 3.3 μF, and VENABLE = VDD. (Note 1). Parameters Output Voltage Accuracy Sym. VO Output Voltage Temperature Coefficient ∆VO/∆T Line Regulation ∆VO/VIN Load Regulation ∆VO/VOUT Dropout Voltage (Note 4) Quiescent Current Ground Pin Current VIN – VO IGND IGND Min. Typ. Max. Units Conditions –1 — 1 –2 — 2 % Variation from specified VOUT — 40 150 ppm/°C Note 2 — 0.004 0.10 — — 0.40 % VIN = VOUT + 1V to 26V — 0.04 0.16 — — 0.30 % IL = 0.1 mA to 100 mA (Note 3) — 17 — IL = 100 µA — 130 — IL = 20 mA — 150 — — 190 — IL = 50 mA — 230 350 IL = 100 mA — 0.01 10 — 130 — VENABLE = VDD, IL = 100 µA — 270 350 IL = 20 mA — 330 — — 500 — IL = 50 mA — 1000 1500 IL = 100 mA mV µA µA IL = 30 mA VENABLE ≤ 0.7V (shutdown) IL = 30 mA Ripple Rejection PSRR — 70 — dB — Ground Pin Current at Dropout IGNDDO — 270 330 µA VIN = 0.5V less than specified VOUT, IL = 100 µA (Note 5) ILIMIT 100 250 — mA VOUT = 0V ∆VO/∆PD — 0.05 — %/W Note 6 en — 100 — µV — Current Limit Thermal Regulation Output Noise Note 1: 2: 3: 4: 5: 6: Specification for packaged product only. Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range. Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for load regulation in the load range from 0.1 mA to 100 mA. Changes in output voltage due to heating effects are covered by the thermal regulation specification. Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at 1V differential. Ground pin current is the regulator quiescent current plus pass transistor base current. The total current drawn from the supply is the sum of the load current plus the ground pin current. Thermal regulation is defined as the change in output voltage at a time (t) after a change in power dissipation is applied, excluding load or line regulation effects. Specifications are for a 100 mA load pulse at VIN = 26V for t = 10 ms. 2016 Microchip Technology Inc. DS20005578A-page 3 MIC5200 TABLE 1-1: ELECTRICAL CHARACTERISTICS (CONTINUED) Electrical Characteristics: Limits in standard typeface are for TJ = 25°C and limits in boldface apply over the junction temperature range of –40°C to +125°C. Unless otherwise specified, VIN = VOUT + 1V, IL = 1 mA, CL = 3.3 μF, and VENABLE = VDD. (Note 1). Parameters Sym. Min. Typ. Max. Input Voltage Level, Logic Low VIL — — 0.7 Input Voltage Level, Logic High VIH 2.0 — — IIL — 0.01 1 IIH — 15 50 Units Conditions ENABLE Input Enable Input Current Note 1: 2: 3: 4: 5: 6: V µA OFF ON VIL ≤ 0.7V VIH ≥ 2.0V Specification for packaged product only. Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range. Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for load regulation in the load range from 0.1 mA to 100 mA. Changes in output voltage due to heating effects are covered by the thermal regulation specification. Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at 1V differential. Ground pin current is the regulator quiescent current plus pass transistor base current. The total current drawn from the supply is the sum of the load current plus the ground pin current. Thermal regulation is defined as the change in output voltage at a time (t) after a change in power dissipation is applied, excluding load or line regulation effects. Specifications are for a 100 mA load pulse at VIN = 26V for t = 10 ms. DS20005578A-page 4 2016 Microchip Technology Inc. MIC5200 TEMPERATURE SPECIFICATIONS Parameters Sym. Min. Typ. Max. Units Conditions Junction Operating Temperature Range TJ –40 — +125 °C Note 1 Lead Temperature — — — +260 °C Soldering, 5s Thermal Resistance, SOT-223 JC — 15 — °C/W — Thermal Resistance, SOIC-8 JA — 160 — °C/W Note 2 Temperature Ranges Package Thermal Resistances Note 1: 2: The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction temperature and the thermal resistance from junction to air (i.e., TA, TJ, JA). Exceeding the maximum allowable power dissipation will cause the device operating junction temperature to exceed the maximum +125°C rating. Sustained junction temperatures above +125°C can impact the device reliability. The maximum allowable power dissipation at any ambient temperature is calculated using: P(MAX) = (TJ(MAX) – TA) ÷ θJA. Exceeding the maximum allowable power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown. The θJC of the MIC5200-x.xYS is 15°C/W and θJA for the MIC5200YM is 160°C/W mounted on a PC board (see Thermal Considerations for further details). 2016 Microchip Technology Inc. DS20005578A-page 5 MIC5200 2.0 Note: TYPICAL PERFORMANCE CURVES The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. 10 GROUND CURRENT (mA) DROPOUT VOLTAGE (mV) 250 200 150 100 50 0 0.01 0.1 0.01 0.1 1 10 100 1000 OUTPUT CURRENT (mA) FIGURE 2-1: Current. Dropout Voltage vs. Output FIGURE 2-4: Current. 0.3 IL = 100mA 0.2 0.1 IL = 1mA 0.0 -60 -30 0 30 60 90 120 150 TEMPERATURE (°C) FIGURE 2-2: Temperature. Ground Current vs. Output Dropout Voltage vs. 1.4 1.2 IL = 100mA 1.0 0.8 0.6 0.4 IL = 1mA 0.2 0.0 0 FIGURE 2-5: Voltage. 3.5 2 4 6 8 SUPPLY VOLTAGE (V) 10 Ground Current vs. Supply 3.5 3.0 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 0.1 1 10 100 OUTPUT CURRENT (mA) 1.6 GROUND CURRENT (mA) DROPOUT VOLTAGE (V) 0.4 IL = 100mA 2.5 2.0 1.5 1.0 IL = 100μA, 1mA 0.5 0.0 1 0 FIGURE 2-3: DS20005578A-page 6 2 4 6 8 INPUT VOLTAGE (V) 10 Dropout Characteristics. 3.0 2.5 2.0 CIN = 2.2μF COUT = 4.7μF 1.5 1.0 0.5 0.0 0.0 FIGURE 2-6: Current. 0.1 0.2 OUTPUT CURRENT (A) 0.3 Output Voltage vs. Output 2016 Microchip Technology Inc. MIC5200 3.6 ILOAD = 100μA CIN = 2.2μF COUT = 4.7μF 0.25 OUTPUT VOLTAGE (V) GROUND CURRENT (mA) 0.30 0.20 0.15 -60 -30 0 30 60 90 120 150 TEMPERATURE (°C) FIGURE 2-7: Temperature. Ground Current vs. 1.2 1.1 1.0 -50 0 50 100 TEMPERATURE (°C) Δ OUTPUT (mV) FIGURE 2-8: Temperature. LOAD (mA) OUTPUT CURRENT (mA) 1.3 0 CL = 4.7 μF -50 200 100 0 -100 -5 FIGURE 2-9: Version). 0 5 10 15 20 25 30 35 TIME (ms) Thermal Regulation (3.3V 2016 Microchip Technology Inc. 3.2 3 DEVICES: HI / AVG / LO 3.1 CURVES APPLICABLE AT 100μA AND 100mA 300 280 260 240 220 200 180 160 140 120 FIGURE 2-11: Temperature. 100 50 3.3 VOUT = 3.3V VOUT = 0V (SHORT CIRCUIT) 100 -60 -30 0 30 60 90 120 150 TEMPERATURE (°C) 150 Ground Current vs. 3.4 FIGURE 2-10: Output Voltage vs. Temperature (3.3V Version). MIN. INPUT VOLTAGE (V) GROUND CURRENT (mA) ILOAD = 100mA CIN = 2.2μF COUT = 4.7μF CIN = 2.2μF COUT = 4.7μF 3.0 -60 -30 0 30 60 90 120 150 TEMPERATURE (°C) 1.5 1.4 3.5 Output Current vs. 3.30 3.29 3.28 3.27 3.26 3.25 CIN = 2.2μF COUT = 4.7μF ILOAD = 1mA 3.24 3.23 3.22 3.21 3.20 -60 -30 0 30 60 90 120 150 TEMPERATURE (°C) FIGURE 2-12: Temperature. Minimum Input Voltage vs. DS20005578A-page 7 300 250 200 150 CIN = 2.2μF COUT = 4.7μF VOUT = 3.3V 100 50 0 1 2 3 4 5 6 INPUT VOLTAGE (V) Short Circuit Current vs. 0 CL = 4.7μF -30 300 200 100 0 -2 0 2 4 6 TIME (ms) 8 0 CL = 47μF 200 100 FIGURE 2-15: DS20005578A-page 8 0 10 20 TIME (ms) 30 Load Transient. RL = 33Ω 20 0 1 2 3 4 5 6 7 8 9 10 SUPPLY VOLTAGE (V) 10 CL = 1 μF IL = 1mA 5 0 -5 -10 8 6 4 2 -0.2 INPUT (V) -30 300 0 -10 40 0 40 0.2 0.4 TIME (ms) 0.6 0.8 Line Transient. FIGURE 2-17: 20 10 -10 -20 60 FIGURE 2-16: Supply Current vs. Supply Voltage (3.3V Version). 10 Load Transient. FIGURE 2-14: 80 0 Δ OUTPUT (mV) 20 10 -10 -20 100 7 INPUT (V) OUTPUT (mA) Δ OUTPUT (mV) FIGURE 2-13: Input Voltage. OUTPUT (mA) Δ OUTPUT (mV) SUPPLY CURRENT (mA) 120 Δ OUTPUT (mV) SHORT CIRCUIT CURRENT (mA) MIC5200 15 10 CL = 10 μF IL = 1mA 5 0 -5 8 6 4 2 -0.1 FIGURE 2-18: 0 0.1 0.2 0.3 0.4 0.5 0.6 TIME (ms) Line Transient. 2016 Microchip Technology Inc. MIC5200 1000 7 OUTPUT (V) ENABLE (V) CL = 4.7 μF IL = 1mA 2 0 0 OUTPUT (V) FIGURE 2-20: Version). 30 25 CIN = 2.2μF COUT = 4.7μF 20 15 VEN = 5V 10 5 0 VEN = 2V FIGURE 2-23: vs. Temperature. Enable Current Threshold 1.6 CL = 4.7 μF IL = 100mA 2 0 FIGURE 2-21: Version). Output Impedance. -5 -60 -30 0 30 60 90 120 150 TEMPERATURE (°C) 50 100 150 200 250 300 TIME (μs) Enable Transient (3.3V 5 4 3 2 1 0 -1 4 -2 -50 FREQUENCY (Hz) FIGURE 2-22: 35 5 4 3 2 1 0 -1 4 -2 -50 IL = 100mA 1x106 1 2 3 4 5 6 SUPPLY VOLTAGE (V) 1x100 0 FIGURE 2-19: Supply Current vs. Supply Voltage (3.3V Version). ENABLE (V) 0.01 0.001 ENABLE CURRENT (μA) 0 0.1 100x103 10 IL = 1mA 1 10x103 RL = 66Ω 20 10 1x103 30 IL = 100μA 100x100 40 100 10x100 OUTPUT IMPEDANCE (Ω) 50 0 50 100 150 200 250 300 TIME (μs) Enable Transient (3.3V 2016 Microchip Technology Inc. ENABLE VOLTAGE (V) SUPPLY CURRENT (mA) 60 1.4 1.2 CIN = 2.2μF COUT = 4.7μF 1 0.8 ON OFF 0.6 0.4 -60 -30 0 30 60 90 120 150 TEMPERATURE (°C) FIGURE 2-24: vs. Temperature. Enable Voltage Threshold DS20005578A-page 9 MIC5200 80 IL = 100μA 60 40 1x106 100x103 10x103 10x100 0 1x103 20 100x100 RIPPLE VOLTAGE (dB) 100 FREQUENCY (Hz) FIGURE 2-25: Ripple vs. Frequency. 80 IL = 1mA 60 40 1x106 100x103 10x103 10x100 0 1x103 20 100x100 RIPPLE VOLTAGE (dB) 100 FREQUENCY (Hz) FIGURE 2-26: Ripple vs. Frequency. 80 IL = 100mA 60 40 1x106 100x103 10x103 10x100 0 1x103 20 100x100 RIPPLE VOLTAGE (dB) 100 FREQUENCY (Hz) FIGURE 2-27: DS20005578A-page 10 Ripple vs. Frequency. 2016 Microchip Technology Inc. MIC5200 3.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 3-1. Package Types MIC5200-x.xYS SOT-223 (S) (Top View) 1 IN TABLE 3-1: MIC5200-x.xYM SOIC-8 (M) MIC5200-x.xYMM MSOP-8 (MM) (Top View) OUT OUT NC GND 2 3 GND OUT IN IN NC EN PIN FUNCTION TABLE Pin Number SOT-223 Pin Number SOIC-8, MSOP-8 Pin Name 3 1, 2 OUT Output: Pins 1 and 2 (SOIC-8, MSOP-8 packages) must be externally connected together. — 3, 6 NC Not internally connected. Connect to ground place for lowest thermal resistance. 2, TAB 4 GND — 5 EN Enable/Shutdown (Input): TTL-compatible. High = enabled; low = shutdown. 1 7, 8 IN Supply Input: Pins 7 and 8 (SOIC-8, MSOP-8 packages) must be externally connected together. 2016 Microchip Technology Inc. Description Ground: Ground pin and TAB (SOT-223 package) are internally connected. DS20005578A-page 11 MIC5200 4.0 APPLICATION INFORMATION 4.1 External Capacitors A 1 μF capacitor is recommended between the MIC5200 output and ground to prevent oscillations due to instability. Larger values serve to improve the regulator's transient response. Most types of tantalum or aluminum electrolytics will be adequate; film types will work, but are costly and therefore not recommended. Many aluminum electrolytics have electrolytes that freeze at about –30°C, so solid tantalum capacitors are recommended for operation below –25°C. The important parameters of the capacitor are an effective series resistance of about 5Ω or less and a resonant frequency above 500 kHz. The value of this capacitor may be increased without limit. At lower values of output current, less output capacitance is required for output stability. The capacitor can be reduced to 0.47 μF for current below 10 mA or 0.33 μF for currents below 1 mA. A 1 μF capacitor should be placed from the MIC5200 input to ground if there is more than 10 inches of wire between the input and the AC filter capacitor or if a battery is used as the input. The MIC5200 will remain stable and in regulation with no load in addition to the internal voltage divider, unlike many other voltage regulators. This is especially important in CMOS RAM keep-alive applications. When used in dual supply systems where the regulator load is returned to a negative supply, the output voltage must be diode clamped to ground. 4.2 ENABLE Input The MIC5200 features nearly zero OFF mode current. When the ENABLE input is held below 0.7V, all internal circuitry is powered off. Pulling this pin high (over 2.0V) re-enables the device and allows operation. The ENABLE pin requires a small amount of current, typically 15 μA. While the logic threshold is TTL/CMOS compatible, ENABLE may be pulled as high as 30V, independent of the voltage on VIN. DS20005578A-page 12 2016 Microchip Technology Inc. MIC5200 5.0 THERMAL CONSIDERATIONS 5.1 Layout The MIC5200-x.xYM (8-pin surface mount package) has the following thermal characteristics when mounted on a single-layer copper-clad printed circuit board. PC Board Dielectric JA FR4 160 °C/W Ceramic 120 °C/W Multi-layer boards having a ground plane, wide traces near the pads, and large supply bus lines provide better thermal conductivity. The "worst case" value of 160 °C/W assumes no ground plane, minimum trace widths, and a FR4 material board. 5.2 Nominal Power Dissipation and Die Temperature The MIC5200-x.xYM at a 25°C ambient temperature will operate reliably at up to 625 mW power dissipation when mounted in the "worst case" manner described above. At an ambient temperature of 55°C, the device may safely dissipate 440 mW. These power levels are equivalent to a die temperature of 125°C, the recommended maximum temperature for non-military grade silicon integrated circuits. For MIC5200-x.xYS (SOT-223 package) heat sink characteristics, please refer to Application Hint 17, “Calculating P.C. Board Heat Sink Area for Surface Mount Packages”. 2016 Microchip Technology Inc. DS20005578A-page 13 MIC5200 6.0 PACKAGING INFORMATION 6.1 Package Marking Information 8-Pin SOIC* XXXX XXYM YYWWC SOT-223* XXXX X.XYSYWWP Legend: XX...X Y YY WW NNN e3 * Example 5200 30YM 1610C Example 5200 3.0YS618P 8-Pin MSOP* Example XXXX X.XY 5200 3.3Y Product code or customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week ‘01’) Alphanumeric traceability code Pb-free JEDEC® designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. ●, ▲, ▼ Pin one index is identified by a dot, delta up, or delta down (triangle mark). Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. Package may or may not include the corporate logo. Underbar (_) symbol may not be to scale. DS20005578A-page 14 2016 Microchip Technology Inc. MIC5200 SOT-223 Package Outline and Recommended Land Pattern Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2016 Microchip Technology Inc. DS20005578A-page 15 MIC5200 8-Lead MSOP Package Outline and Recommended Land Pattern Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS20005578A-page 16 2016 Microchip Technology Inc. MIC5200 8-Lead SOIC-N Package Outline and Recommended Land Pattern Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2016 Microchip Technology Inc. DS20005578A-page 17 MIC5200 DS20005578A-page 18 2016 Microchip Technology Inc. MIC5200 APPENDIX A: REVISION HISTORY Revision A (July 2016) • Converted Micrel document MIC5200 to Microchip data sheet DS20005578A. • Minor text changes throughout. 2016 Microchip Technology Inc. DS20005578A-page 19 MIC5200 NOTES: DS20005578A-page 20 2016 Microchip Technology Inc. MIC5200 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, contact your local Microchip representative or sales office. – PART NO. Device X.X X MIC5200: Voltage: (Note 1) 3.0 3.3 4.8 5.0 Temperature: Y Package: M = MM = S = 8-Pin SOIC 8-Pin MSOP SOT-223 TR = blank= 2,500/Reel 95/Tube Note 1: – Examples: X.X a) MIC5200-3.0YM: 100 mA Low-Dropout Regulator, 3.0V Voltage, –40°C to +125°C Temp. Range, 8Pin SOIC, 95/Tube b) MIC5200-4.8YM-TR: 100 mA Low-Dropout Regulator, 4.85 Voltage, –40°C to +125°C Temp. Range, 8Pin SOIC, 2,500/Reel c) MIC5200-3.3YMM: 100 mA Low-Dropout Regulator, 3.3V Voltage, –40°C to +125°C Temp. Range, 8Pin MSOP, 95/Tube d) MIC5200-5.0YMM-TR: 100 mA Low-Dropout Reg- Voltage Temperature Package Media Type Device: Media Type: XX = = = = = 100 mA Low-Dropout Regulator 3.0V 3.3V 4.8V 5.0V –40°C to +125°C The 8-Pin MSOP package (MM) is only available in 3.3V and 5.0V options. ulator, 5.0V Voltage, –40°C to +125°C Temp. Range, 8Pin MSOP, 2,500/Reel e) MIC5200-3.3YS: 100 mA Low-Dropout Regulator, 3.3V Voltage, –40°C to +125°C Temp. Range, SOT-223, 95/Tube f) MIC5200-5.0YS-TR 100 mA Low-Dropout Regulator, 5.0V Voltage, –40°C to +125°C Temp. Range, SOT-223, 2,500/ Reel 2016 Microchip Technology Inc. DS20005578A-page 21 MIC5200 NOTES: DS20005578A-page 22 2016 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights unless otherwise stated. Trademarks The Microchip name and logo, the Microchip logo, AnyRate, dsPIC, FlashFlex, flexPWR, Heldo, JukeBlox, KeeLoq, KeeLoq logo, Kleer, LANCheck, LINK MD, MediaLB, MOST, MOST logo, MPLAB, OptoLyzer, PIC, PICSTART, PIC32 logo, RightTouch, SpyNIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. ClockWorks, The Embedded Control Solutions Company, ETHERSYNCH, Hyper Speed Control, HyperLight Load, IntelliMOS, mTouch, Precision Edge, and QUIET-WIRE are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM, ECAN, EtherGREEN, In-Circuit Serial Programming, ICSP, Inter-Chip Connectivity, JitterBlocker, KleerNet, KleerNet logo, MiWi, motorBench, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, PureSilicon, RightTouch logo, REAL ICE, Ripple Blocker, Serial Quad I/O, SQI, SuperSwitcher, SuperSwitcher II, Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV == ISO/TS 16949 == 2016 Microchip Technology Inc. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. GestIC is a registered trademarks of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. © 2016, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. ISBN: 978-1-5224-0785-0 DS20005578A-page 23 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Germany - Dusseldorf Tel: 49-2129-3766400 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Hong Kong Tel: 852-2943-5100 Fax: 852-2401-3431 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 Austin, TX Tel: 512-257-3370 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Novi, MI Tel: 248-848-4000 Houston, TX Tel: 281-894-5983 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 New York, NY Tel: 631-435-6000 San Jose, CA Tel: 408-735-9110 Canada - Toronto Tel: 905-695-1980 Fax: 905-695-2078 China - Dongguan Tel: 86-769-8702-9880 China - Guangzhou Tel: 86-20-8755-8029 China - Hangzhou Tel: 86-571-8792-8115 Fax: 86-571-8792-8116 China - Hong Kong SAR Tel: 852-2943-5100 Fax: 852-2401-3431 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 China - Shenzhen Tel: 86-755-8864-2200 Fax: 86-755-8203-1760 India - Pune Tel: 91-20-3019-1500 Japan - Osaka Tel: 81-6-6152-7160 Fax: 81-6-6152-9310 Japan - Tokyo Tel: 81-3-6880- 3770 Fax: 81-3-6880-3771 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Germany - Karlsruhe Tel: 49-721-625370 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Italy - Venice Tel: 39-049-7625286 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Poland - Warsaw Tel: 48-22-3325737 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 Sweden - Stockholm Tel: 46-8-5090-4654 UK - Wokingham Tel: 44-118-921-5800 Fax: 44-118-921-5820 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 Taiwan - Kaohsiung Tel: 886-7-213-7828 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Taipei Tel: 886-2-2508-8600 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 06/23/16 DS20005578A-page 24 2016 Microchip Technology Inc.