ISOCOM COMPONENTS IS480P DESCRIPTION The IS480P High Speed Photocoupler contains a AlGaAs LED and Photo detector with built-in Schmitt Trigger to provide logic-compatible waveforms, eliminating the need for additional wave shaping. 1 Anode 2 NC 3 Cathode The totem pole output eliminates the need for a pull up resistor and allows for direct Intelligent Power Module Drive or Gate Drive. Minimized Propagation Delay difference between devices makes this photocoupler excellent solutions for improving inverter efficiency through reduced switching dead time. The device is in Stretched SO6 package. 4 GND 5 VO 6 VCC A 0.1μF bypass Capacitor must be connected between Pins 6 and 4. FEATURES Totem Pole Output Wide Operating Voltage Range VCC 4.5V to 30V Operating Temperature Range - 40°C to +105°C Performance specified for Common IPM Applications over Industrial Temperature range. Maximum Propagation Delays tPLH / tPHL : 200ns / 220ns Propagation Delay Difference Min / Max : -210ns / 210ns Maximum Pulse Width Distortion PWD : 120ns Hysteresis 20kV/μs Minimum Common Mode Rejection at VCM 1500V Lead Free and RoHS Compliant Safety Approvals Pending ABSOLUTE MAXIMUM RATINGS (TA = 25°C) Stresses exceeding the absolute maximum ratings can cause permanent damage to the device. Exposure to absolute maximum ratings for long periods of time can adversely affect reliability. Input Forward Current Forward Peak Current 10mA 1.0A Reverse Voltage 5V (Pulse Width < 1μs, 300pps) Output Output Current Output Voltage Supply Voltage APPLICATIONS Total Package Isolation Voltage Total Power Dissipation Operating Temperature Storage Temperature Lead Soldering Temperature (10s) Isolated IGBT/MOSFET Gate Drive IPM Interface Isolation Industrial Inverters AC Brushless and DC Motor Drives Digital Isolation 50mA -0.5V to 35V 35V 5000VRMS 145mW -40 to 105 °C -55 to 125 °C 260°C ORDER INFORMATION Supply in Tape & Reel ISOCOM COMPONENTS 2004 LTD Unit 25B, Park View Road West, Park View Industrial Estate Hartlepool, Cleveland, TS25 1PE, United Kingdom Tel: +44 (0)1429 863 609 Fax : +44 (0)1429 863 581 e-mail: [email protected] http://www.isocom.com 1 21/09/2016 ISOCOM COMPONENTS ASIA LTD Hong Kong Office, Block A, 8/F, Wah Hing Industrial mansion, 36 Tai Yau Street, San Po Kong, Kowloon, Hong Kong. Tel: +852 2995 9217 Fax : +852 8161 6292 e-mail [email protected] DC93200 ISOCOM COMPONENTS IS480P Truth Table LED VO ON HIGH OFF LOW Recommended Operating Conditions Parameter Symbol Min Max Unit Operating Temperature TA - 40 105 °C Supply Voltage VCC 4.5 30 V Input Current (ON) IF(ON) 1.6 5 mA Input Voltage (OFF) VF(OFF) 0.8 V Note : 1: Photo Detector requires a VCC of 4.5 V or higher for stable operation as output might be unstable if VCC is lower than 4.5 V. 2: The initial switching threshold is 1.6 mA or less. It is recommended that 2.2 mA be used to permit a guard band. 2 21/09/2016 DC93200 ISOCOM COMPONENTS IS480P ELECTRICAL CHARACTERISTICS (Over Recommended Operating Conditions, VCC = 4.5V to 30V, IF(ON) = 1.6mA to 5mA, VF(OFF) = 0V to 0.8V, TA = -40°C to 105°C, unless otherwise specified. Typical Values at T A = 25°C) INPUT Parameter Symbol Test Condition Min Typ. Max Unit Forward Voltage VF IF = 5mA 1.2 1.33 1.6 V Forward Voltage Temperature Coefficient ΔVF/ΔT IF = 5mA Reverse Voltage VR IR = 10μA Input Threshold Current (Low to High) IFLH Input Threshold Voltage (High to Low) VFHL Input Capacitance -1.237 mV/°C 5 V 0.7 1.5 0.8 CIN VF = 0V, f = 1MHz Symbol Test Condition ICCH VCC = 5.5V, IF = 5mA IO = 0mA mA V 33 pF OUTPUT Parameter High Level Supply Current Min VCC = 30V, IF = 5mA IO = 0mA Low Level Supply Current ICCL 1.9 VCC = 5.5V, VF = 0V IO = 0mA Low Level Short Circuit Output Current IOSH IOSL Unit 3.0 mA 3.0 2.0 -160 VCC = 20V, IF = 5mA, VO = GND Duration < 500µs -200 VO = VCC = 5.5V, VF = 0V Duration < 500µs 160 VO = VCC = 20V, VF = 0V Duration < 500µs 200 VOH IOH = -6.5mA Low Level Output Voltage VOL IOL = 6.5mA mA 3.0 VCC = 5.5V, IF = 5mA, VO = GND Duration < 500µs High Level Output Voltage 3 21/09/2016 Max 3.0 VCC = 30V, VF = 0V IO = 0mA High Level Short Circuit Output Current Typ. mA mA VCC - 0.5 VCC - 0.025 0.015 V 0.5 DC93200 V ISOCOM COMPONENTS IS480P ELECTRICAL CHARACTERISTICS (Over Recommended Operating Conditions, VCC = 4.5V to 30V, IF(ON) = 1.6mA to 5mA, VF(OFF) = 0V to 0.8V, TA = -40°C to 105°C, unless otherwise specified. Typical Values at T A = 25°C) SWITCHING Parameter Symbol Test Condition Propagation Delay Time to High Output Level tPLH Propagation Delay Time to Low Output Level Min Typ. Max Unit VF = 0V → IF(ON) = 1.6mA CL = 100pF 120 200 ns tPHL IF(ON) = 1.6mA → VF = 0V CL = 100pF 130 220 Pulse Width Distortion |tPHL - tPLH| for any given device PWD CL = 100pF Propagation Delay Difference (tPHL - tPLH) between any two devices PDD CL = 100pF 120 -210 210 Output Rise Time (10% to 90%) tr 35 Output Fall Time (90% to 10%) tf 35 Common Mode Transient Immunity at High Output Level CMH IF = 6.0mA VCC = 5V VCM = 1500V TA = 25°C 20 kV/μs Common Mode Transient Immunity at Low Output Level CML VF = 0V VCC = 5V VCM = 1500V TA = 25°C 20 kV/μs Note : 1. A 0.1uF or bigger bypass capacitor must be connected across pin 6 and pin 4. 2. tPLH propagation delay is measured from the 50% point on the leading edge of the input pulse to the 1.3 V point on the leading edge of the output pulse. tPHL propagation delay is measured from the 50% point on the trailing edge of the input pulse to the 1.3 V point on the trailing edge of the output pulse. 3. PDD is the difference of tPHL and tPLH between any two devices under same test conditions. 4. CMH, Common Mode Transient Immunity in High stage is the maximum tolerable slew rate of the common mode impulse signal, VCM, to assure that the output will remain high (VO > 2V). Equal value split resistors must be used at both ends of the LED. 5. CML, Common Mode Transient Immunity in Low stage is the maximum tolerable slew rate of the common mode impulse signal, VCM, to assure that the output will remain low (VO < 0.8V). Equal value split resistors must be used at both ends of the LED. 4 21/09/2016 DC93200 ISOCOM COMPONENTS IS480P ELECTRICAL CHARACTERISTICS (Over Recommended Operating Conditions, TA = -40°C to 105°C, unless otherwise specified. Typical Values at T A = 25°C) ISOLATION Parameter Symbol Test Condition Min Insulation Voltage VISO RH ≤ 50%, t = 1 min, TA = 25°C 5000 Input - Output Resistance RI-O VI-O = 500VDC 1012 Ω Input - Output Capacitance CI-O f = 1MHz, TA = 25°C 1.0 pF 5 21/09/2016 Typ. Max Unit VRMS DC93200 ISOCOM COMPONENTS IS480P Fig 1 Forward Current vs Forward Voltage Fig 2 High Level Output Voltage vs Supply Voltage Fig 3 Low Level Output Voltage vs Ambient Temperature Fig 4 High Level Output Voltage Drop vs Ambient temperature Fig 5 Hysteresis Output Voltage vs Input Threshold Current Fig 6 Input Threshold Current vs Ambient Temperature 6 21/09/2016 DC93200 ISOCOM COMPONENTS IS480P Fig 7 Propagation Delay vs Ambient Temperature at VCC 4.5V Fig 8 Propagation Delay vs Ambient Temperature at VCC 30V Fig 9 Propagation Delay vs Supply Voltage 7 21/09/2016 DC93200 ISOCOM COMPONENTS IS480P Vo Monitor 0.1µF IF Monitor Vo Monitor IF Monitor tr, tf, tPLH and tPHL Test Circuit and Waveform 8 21/09/2016 DC93200 ISOCOM COMPONENTS IS480P Equal value split resistors must be used at both ends of the LED. CMR Test Circuit and Waveform 9 21/09/2016 DC93200 ISOCOM COMPONENTS IS480P ORDER INFORMATION IS480P After PN None PN Description Packing quantity IS480P Stretched SO6 1000 pcs per reel DEVICE MARKING 480P YYWW 480P denotes Device Part Number YY denotes 2 digit Year code WW denotes 2 digit Week code 10 21/09/2016 DC93200 ISOCOM COMPONENTS IS480P PACKAGE DIMENSIONS and Recommended PCB Pad Layout in mm (inch) 11 21/09/2016 DC93200 ISOCOM COMPONENTS IS480P TAPE AND REEL PACKAGING Description Symbol Dimension mm (inch) Tape Width W 16 ± 0.3 (0.63) Pitch of Sprocket Holes P0 4 ± 0.1 (0.16) F 7.5 ± 0.1 (0.3) P2 2 ± 0.1 (0.079) P1 12 ± 0.1 (0.47) Distance of Compartment to Sprocket Holes Distance of Compartment to Compartment 12 21/09/2016 DC93200 ISOCOM COMPONENTS IS480P IR REFLOW SOLDERING TEMPERATURE PROFILE (One Time Reflow Soldering is Recommended) TP 260°C TP - 5°C TEMP (°C) Max Ramp Up Rate 3°C/s TL 217°C Tsmax 200°C tP Max Ramp Down Rate 6°C/s TL Tsmin 150°C ts Preheat 60s – 120s 25°C TIME (s) Time 25°C to Peak Temperature Profile Details Conditions Preheat - Min Temperature (TSMIN) - Max Temperature (TSMAX) - Time TSMIN to TSMAX (ts) 150°C 200°C 60s - 120s Soldering Zone - Peak Temperature (TP) - Time at Peak Temperature - Liquidous Temperature (TL) - Time within 5°C of Actual Peak Temperature (T P ̶ 5°C) - Time maintained above TL (tL) - Ramp Up Rate (TL to TP) - Ramp Down Rate (TP to TL) 260°C 10s max 217°C 30s max 60s - 100s 3°C/s max 6°C/s max Average Ramp Up Rate (Tsmax to TP) 3°C/s max Time 25°C to Peak Temperature 8 minutes max 13 21/09/2016 DC93200 ISOCOM COMPONENTS IS480P NOTES : - Isocom is continually improving the quality, reliability, function or design and Isocom reserves the right to make changes without further notices. - The products shown in this publication are designed for the general use in electronic applications such as office automation equipment, communications devices, audio/visual equipment, electrical application and instrumentation. - For equipment/application where high reliability or safety is required, such as space applications, nuclear power control equipment, medical equipment, etc., please contact our sales representatives. - When requiring a device for any ”specific” application, please contact our sales for advice. - The contents described herein are subject to change without prior notice. - Do not immerse device body in solder paste. 14 21/09/2016 DC93200 ISOCOM COMPONENTS DISCLAIMER ISOCOM is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing ISOCOM products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such ISOCOM products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that ISOCOM products are used within specified operating ranges as set forth in the most recent ISOCOM products specifications. __ The ISOCOM products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These ISOCOM products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation Instruments, traffic signal instruments, combustion control instruments, medical Instruments, all types of safety devices, etc.. Unintended Usage of ISOCOM products listed in this document shall be made at the customer’s own risk. __ Gallium arsenide (GaAs) is a substance used in the products described in this document. GaAs dust and fumes are toxic. Do not break, cut or pulverize the product, or use chemicals to dissolve them. When disposing of the products, follow the appropriate regulations. Do not dispose of the products with other industrial waste or with domestic garbage. __ The products described in this document are subject to the foreign exchange and foreign trade laws. __ The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by ISOCOM Components for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of ISOCOM Components or others. __ The information contained herein is subject to change without notice. 15 21/09/2016 DC93200