ON MC74HCT259A Highâ performance siliconâ gate cmo Datasheet

MC74HCT259A
8-Bit Addressable Latch
1-of-8 Decoder with LSTTL
Inputs
High−Performance Silicon−Gate CMOS
The MC74HCT259A is identical in pinout to the LS259. The device
inputs are compatible with standard CMOS and LSTTL outputs.
The HCT259A has four modes of operation as shown in the mode
selection table. In the addressable latch mode, the data on Data In is
written into the addressed latch. The addressed latch follows the data
input with all non−addressed latches remaining in their previous
states. In the memory mode, all latches remain in their previous state
and are unaffected by the Data or Address inputs. In the one−of−eight
decoding or demultiplexing mode, the addressed output follows the
state of Data In with all other outputs in the LOW state. In the Reset
mode all outputs are LOW and unaffected by the address and data
inputs. When operating the HCT259A as an addressable latch,
changing more than one bit of the address could impose a transient
wrong address. Therefore, this should only be done while in the
memory mode.
Features
•
•
•
•
•
•
Output Drive Capability: 10 LSTTL Loads
Outputs Directly Interface to CMOS, NMOS, and TTL
Operating Voltage Range: 4.5 to 5.5 V
Low Input Current: 1 mA
High Noise Immunity Characteristic of CMOS Devices
These are Pb−Free Devices
http://onsemi.com
MARKING
DIAGRAMS
16
SOIC−16
D SUFFIX
CASE 751B
16
1
HCT259AG
AWLYWW
1
16
HCT
259A
ALYWG
G
TSSOP−16
DT SUFFIX
CASE 948F
16
1
1
A
= Assembly Location
WL, L
= Wafer Lot
YY, Y
= Year
WW, W = Work Week
G or G
= Pb−Free Package
(Note: Microdot may be in either location)
PIN ASSIGNMENT
A0
1
16
VCC
A1
2
15
RESET
A2
3
14
ENABLE
Q0
4
13
DATA IN
Q1
5
12
Q7
Q2
6
11
Q6
Q3
7
10
Q5
GND
8
9
Q4
MODE SELECTION TABLE
Enable
Reset
Mode
L
H
L
H
H
H
L
L
Addressable Latch
Memory
8−Line Demultiplexer
Reset
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 6 of this data sheet.
© Semiconductor Components Industries, LLC, 2011
April, 2011 − Rev. 3
1
Publication Order Number:
MC74HCT259A/D
MC74HCT259A
ADDRESS
INPUTS
4
Q0
5
Q1
6
Q2
7
Q3
9
Q4
10
Q5
11
Q6
12
Q7
1
A0
2
A1
3
A2
DATA IN
13
15
RESET
14
ENABLE
LATCH SELECTION TABLE
Address Inputs
NONINVERTING
OUTPUTS
PIN 16 = VCC
PIN 8 = GND
C
B
A
Latch Addressed
L
L
L
L
H
H
H
H
L
L
H
H
L
L
H
H
L
H
L
H
L
H
L
H
Q0
Q1
Q2
Q3
Q4
Q5
Q6
Q7
Figure 1. Logic Diagram
MAXIMUM RATINGS
Symbol
Parameter
Value
Unit
VCC
DC Supply Voltage (Referenced to GND)
−0.5 to +7.0
V
Vin
DC Input Voltage (Referenced to GND)
−0.5 to VCC + 0.5
V
Vout
DC Output Voltage (Referenced to GND)
−0.5 to VCC + 0.5
V
Iin
DC Input Current, per Pin
±20
mA
Iout
DC Output Current, per Pin
±25
mA
ICC
DC Supply Current, VCC and GND Pins
±50
mA
PD
Power Dissipation in Still Air,
500
450
mW
Tstg
Storage Temperature
−65 to + 150
°C
VESD
ILatchup
SOIC Package
TSSOP Package
ESD Withstand Voltage
V
Human Body Model (Note 1)
Machine Model (Note 2)
>2000
>200
Latchup Performance Above VDD and Below GND at
125°C (Note 3)
mA
±100
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress
ratings only. Functional operation above the Recommended Operating Conditions is not implied.
Extended exposure to stresses above the Recommended Operating Conditions may affect device
reliability.
1. Tested to EIA / JESD22−A114−A.
2. Tested to EIA / JESD22−A115−A.
3. Tested to EIA / JESD78.
RECOMMENDED OPERATING CONDITIONS
Symbol
VCC
Vin, Vout
Parameter
Min
DC Supply Voltage (Referenced to GND)
DC Input Voltage, Output Voltage (Referenced to GND)
TA
Operating Temperature, All Package Types
tr, tf
Input Rise and Fall Time (Figure 2)
Max
Unit
4.5
5.5
V
0
VCC
V
−55
+125
°C
0
500
ns
http://onsemi.com
2
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high−impedance circuit. For proper operation, Vin and
Vout should be constrained to the
range GND v (Vin or Vout) v VCC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or VCC).
Unused outputs must be left open.
MC74HCT259A
DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND)
Guaranteed Limit
Symbol
Parameter
Test Conditions
VCC
V
− 55 to
25°C
v 85°C
v 125°C
Unit
VIH
Minimum High−Level Input
Voltage
Vout = 0.1 V or VCC − 0.1 V
|Iout| v 20 mA
4.5
5.5
2.0
2.0
2.0
2.0
2.0
2.0
V
VIL
Maximum Low−Level Input
Voltage
Vout = 0.1 V or VCC − 0.1 V
|Iout| v 20 mA
4.5
5.5
0.8
0.8
0.8
0.8
0.8
0.8
V
VOH
Minimum High−Level Output
Voltage
Vin = VIH or VIL
|Iout| v 20 mA
4.5
5.5
4.4
5.4
4.4
5.4
4.4
5.4
V
4.5
3.98
3.84
3.70
4.5
5.5
0.1
0.1
0.1
0.1
0.1
0.1
Vin = VIH or VIL
VOL
Maximum Low−Level Output
Voltage
|Iout| v 5.2 mA
Vin = VIH or VIL
|Iout| v 20 mA
Vin = VIH or VIL
4.5
0.26
0.33
0.40
Iin
Maximum Input Leakage
Current
Vin = VCC or GND
5.5
± 0.1
± 1.0
± 1.0
mA
ICC
Maximum Quiescent Supply
Current (per Package)
Vin = VCC or GND
Iout = 0 mA
5.5
4
40
160
mA
DICC
Additional Quiescent Supply
Current
|Iout| v 5.2 mA
V
Vin = 2.4V, Any One Input
Vin = VCC or GND, Other Inputs
Iout = 0mA
http://onsemi.com
3
5.5
≥ −55°C
25 to 125°C
2.9
2.4
mA
MC74HCT259A
AC ELECTRICAL CHARACTERISTICS (VCC = 4.5 to 5.5 V, CL = 50 pF, Input tr = tf = 6 ns)
Guaranteed Limit
Symbol
Parameter
−55 to
25°C
v 85°C
v 125°C
Unit
tPLH,
tPHL
Maximum Propagation Delay, Data to Output
(Figures 2 and 7)
32
32
42
ns
tPLH,
tPHL
Maximum Propagation Delay, Address Select to Output
(Figures 3 and 7)
32
40
45
ns
tPLH,
tPHL
Maximum Propagation Delay, Enable to Output
(Figures 4 and 7)
32
40
45
ns
tPHL
Maximum Propagation Delay, Reset to Output
(Figures 5 and 7)
22
26
32
ns
tTLH,
tTHL
Maximum Output Transition Time, Any Output
(Figures 2 and 7)
15
19
22
ns
Maximum Input Capacitance
10
10
10
pF
Cin
Typical @ 25°C, VCC = 5.0 V
CPD
30
Power Dissipation Capacitance (Per Package)
pF
TIMING REQUIREMENTS (VCC = 4.5 to 5.5 V, Input tr = tf = 6 ns)
Guaranteed Limit
Symbol
Parameter
−55 to
25°C
v 85°C
v 125°C
Unit
tsu
Minimum Setup Time, Address or Data to Enable
(Figure 6)
15
19
22
ns
th
Minimum Hold Time, Enable to Address or Data
(Figure 6)
1
1
1
ns
tw
Minimum Pulse Width, Reset or Enable
(Figure 4 or 5)
15
19
22
ns
http://onsemi.com
4
MC74HCT259A
SWITCHING WAVEFORMS
3.0V
DATA IN
GND
3.0V
1.3 V
tf
tr
DATA IN
3.0 V
90%
1.3 V
10%
3.0V
GND
1.3 V
GND
tPHL
tPLH
90%
1.3 V
10%
OUTPUT Q
GND
ADDRESS
SELECT
tPHL
tPLH
50%
50%
OUTPUT Q
tTLH
tTHL
Figure 2.
Figure 3.
3.0 V
3.0V
DATA IN
tw
tw
1.3 V
1.3 V
DATA IN
GND
GND
tw
VCC
ENABLE
tPHL
tPLH
1.3 V
RESET
GND
GND
tPHL
50%
OUTPUT Q
3.0V
1.3 V
50%
OUTPUT Q
Figure 4.
Figure 5.
TEST POINT
DATA IN
OR
ADDRESS
SELECT
ENABLE
OUTPUT
3.0V
1.3 V
th(L)
th(H)
tsu
tsu
GND
DEVICE
UNDER
TEST
CL*
3.0V
1.3 V
GND
*Includes all probe and jig capacitance
Figure 6.
Figure 7. Test Circuit
http://onsemi.com
5
MC74HCT259A
DATA INPUT
13
D
D
D
D
4
5
6
7
Q0
Q1
Q2
Q3
A0
ADDRESS
INPUTS
3 TO 8
DECODER
A1
D
A2
D
ENABLE
10
Q4
Q5
14
D
D
RESET
9
11
12
Q6
Q7
15
Figure 8. Expanded Logic Diagram
ORDERING INFORMATION
Package
Shipping†
MC74HCT259ADG
SOIC−16
(Pb−Free)
48 Units / Rail
MC74HCT259ADR2G
SOIC−16
(Pb−Free)
2500 Tape & Reel
TSSOP−16*
2500 Tape & Reel
Device
MC74HCT259ADTR2G
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*This package is inherently Pb−Free.
http://onsemi.com
6
MC74HCT259A
PACKAGE DIMENSIONS
SOIC−16
CASE 751B−05
ISSUE K
−A−
16
9
1
8
−B−
P
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D
DIMENSION AT MAXIMUM MATERIAL CONDITION.
8 PL
0.25 (0.010)
M
B
S
G
R
K
F
X 45 _
C
−T−
SEATING
PLANE
J
M
D
16 PL
0.25 (0.010)
M
T B
S
A
S
SOLDERING FOOTPRINT*
8X
6.40
16X
1
1.12
16
16X
0.58
1.27
PITCH
8
9
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
7
DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
9.80
10.00
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0_
7_
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.386
0.393
0.150
0.157
0.054
0.068
0.014
0.019
0.016
0.049
0.050 BSC
0.008
0.009
0.004
0.009
0_
7_
0.229
0.244
0.010
0.019
MC74HCT259A
PACKAGE DIMENSIONS
TSSOP−16
DT SUFFIX
CASE 948F−01
ISSUE B
16X K REF
0.10 (0.004)
0.15 (0.006) T U
T U
M
S
V
S
K
ÇÇÇ
ÇÇÇ
ÉÉÉ
ÇÇÇ
ÉÉÉ
S
K1
2X
L/2
16
9
J1
B
−U−
L
SECTION N−N
J
PIN 1
IDENT.
N
8
1
0.25 (0.010)
M
0.15 (0.006) T U
S
A
−V−
N
F
DETAIL E
C
0.10 (0.004)
−T− SEATING
PLANE
D
H
G
DETAIL E
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH. PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL
NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08
(0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
MILLIMETERS
INCHES
DIM MIN
MAX
MIN
MAX
A
4.90
5.10 0.193 0.200
B
4.30
4.50 0.169 0.177
C
−−−
1.20
−−− 0.047
D
0.05
0.15 0.002 0.006
F
0.50
0.75 0.020 0.030
G
0.65 BSC
0.026 BSC
H
0.18
0.28 0.007
0.011
−W−
J
0.09
0.20 0.004 0.008
J1
0.09
0.16 0.004 0.006
K
0.19
0.30 0.007 0.012
K1
0.19
0.25 0.007 0.010
L
6.40 BSC
0.252 BSC
M
0_
8_
0_
8_
SOLDERING FOOTPRINT*
7.06
1
0.65
PITCH
16X
0.36
16X
1.26
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
8
MC74HCT259A
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
9
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC74HCT259A/D
Similar pages