Hirose DF25G-30S-0.5SD 0.5 mm contact pitch, board-to-fpc, board-to-fine coaxial ribbon cable Datasheet

NEW
0.5 mm Contact Pitch, Board-to-FPC, Board-to-Fine Coaxial Ribbon Cable
(8.9)
(1.1)
Fine Coaxial
Ribbon Cable
(0.7)
DF25 Series
Board
(8.9)
(1.1)
FPC
(0.7)
DF25G-*S-0.5SD
Board
DF25G-*S-0.5F
■Features
1. Supports High Speed Data Transfer
2 Gbps Eye Pattern
Typical Data Transfer of 1.2 Gbps. Up to 2 Gbps in
specific applications.
*The transmission characteristics depends on the
specific conditions and may vary. It is recommended
that verification be made with the actual device in use.
2. Small configuration and board space
0.5 mm contact pitch and body thickness of 1.1 mm. max.
3. Common Use of Receptacle
The board mounted receptacle assembly will accept
mating connectors terminated to FPC or Fine Coaxial
Cable Ribbon Cable.
4. Uniform External Dimensions
The Plug Assembly external dimensions remain the
same when it is terminated with FPC or the Fine Pitch
Coaxial Ribbon Cable.
5. Ground Connection
Metal Shield Covers connect with the common ground line.
6. Easy Termination of FFC or Fine Coaxial
Ribbon Cable
Hirose Electric's unique termination method allows
reduction of the number steps to terminate FFC or Fine
Coaxial Ribbon Cable. Termination can be performed in
any work environment since there is no need for the
electric power supply.
7. Environmental considerations
Plating compounds are lead-free.
■Applications
LCD connections in small consumer devices, Digital
Cameras, Notebook computers, PDA's.
Any device requiring high density interconnection for
consistent high speed transmission data rates.
FPC Type
Fine Coaxial
Ribbon Cable Type
2003.5
1
■Product Specifications
FPC: 0.5 A DC (Note 1)
Current rating Fine Coaxial Ribbon Cable AWG#36: 0.5A Operating temperature -35ç to +85ç (Note 2) Operating temperature -10ç to +60ç (Note 3)
Fine Coaxial Ribbon Cable AWG#40: 0.3A
Voltage rating 50 V AC
Operating humidity
20% to 80%
Operating humidity
40% to 70% (Note 3)
Ratings
Item
Specification
Conditions
1. Insulation resistance
2. Withstanding voltage
3. Contact resistance
4. Insertion-Extraction force
(per contact)
500 M ohms min.
No flashover or insulation breakdown
50 m ohms max.
100 V DC
200 V AC / one minute
100 mA
Min. 0.15n, Max. 2N
Measured with a steel pin 0.15∞0.26±0.005
5. Vibration
No electrical discontinuity of 1 µs or more.
Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in
each of the 3 directions
6. Humidity(Steady state)
7. Temperature cycle
Contact resistance: 120 m ohms max.
Insulation resistance: 500 M ohms min.
Contact resistance: 120 m ohms max.
Insulation resistance: 500 M ohms min.
8. Durability
Contact resistance: 120 m ohms max.
(insertion/ withdrawal)
No deformation of the insulator parts affecting
9. Resistance to
performance.
soldering heat
96 hours at temperature of 40ç and humidity of 90% to 95%
Temperature: -55ç → +5ç to +35ç → +85ç → +5ç to +35ç
Time sequence: 30 → 10 → 30 → 10 (Minutes) 5 cycles
30 cycles
Re-flow soldering: At the recommended temperature profile
Manual soldering: Soldering iron temperature 300ç, 3 seconds
Note 1: Please contact FPC manufacturer for specifications.
Note 2: Includes temperature rise caused by current flow.
Note 3: The term "storage" refers to connectors stored for long period of time prior to mounting and use. Operating
Temperature Range and Humidity range covers non- conducting condition of installed connectors in storage,
shipment or during transportation.
■Materials
Product
Receptacle
FPC Plug
Fine Coaxial
Ribbon Cable Plug
Shield Cover
2
Part
Material
Finish
Color
Remarks
Insulator
Contacts
Shield plate
Insulator
Contact
Shield plate
Insulator
Contact
Glass reinforced thermoplastic
Phosphor bronze
Phosphor bronze
Glass reinforced thermoplastic
Phosphor bronze
Phosphor bronze
Glass reinforced thermoplastic
Phosphor bronze
---------------Gold plating
Tin plating
---------------Gold plating
Tin plating
---------------Gold plating
Obverse side: Tin plating
Reverse side: Insulation coating
Black
------------------------------Black
------------------------------Black
----------------
UL94V-0
------------------------------UL94V-0
------------------------------UL94V-0
----------------
----------------
----------------
Stainless steel
■Ordering information
DF25 L - 36 P - 0.5 H
1
2
3
4
5
6
DF25 G - 36 S - 0.5 F/SD - GND
1
2
3
4
5
6
1 Ordering Information : DF25
5 Contact pitch :0.5mm
2 Configuration
6 Termination section
Receptacle
L: Offset type (0.7mm above the board)
Plug
G: Ground connection type
3 Number of contacts: 20,30,36
4 Connector type
S: Plug
7
H: Right angle SMT
F: FPC Plug
SD: Plug - Fine Pitch Coaxial Ribbon Cable
F/SD: Common to FPC Plug & Fine
Coaxial Ribbon Cable Plug
7 Metal shell
G: Shielding plate
P: Receptacle
3
■ Right angle Receptacle (SMT)
(Offset mounting type)
A±0.3
B±0.15
4±0.3
0.2±0.05
C±0.3
1.1 MAX
CAV No.
0.7±0.15
Contact No. 1
identification mark
5±0.3
1.42±0.1
P=0.5±0.08
B PCB mounting pattern
+0.1
0
B±0.05
0.3±0.05
(3.9)
3.9±0.1
0.5±0.1
+0.1
1.1 0
2.3 +0.1
0
3.7±0.1
1.2
P=0.5±0.05
D±0.1
E±0.1
Packaging code: -**,(**)
(51): Embossed tape packaging (2,000 pieces per reel)
Unite: mm
Part Number
CL No.
Number of contacts
A
B
C
D
E
DF25L-20P-0.5H(**)
Reserved for
20
17.46
19.5
17.5
14.9
15.9
DF25L-30P-0.5H(**)
product expansion
30
22.46
14.5
22.4
19.9
20.9
DF25L-36P-0.5H(**)
662-0009-0-**
36
25.46
17.5
25.4
22.9
23.9
Note: Embossed tape reel packaging (2,000 pieces/reel).Order by number of reels.
4
Remarks
0.7mm above
the board
■ Plug (FPC Type)
Note 1: Requires use of plug and shield cover.
Note 2: Requires use of dedicated assembly tools.
Contact No. 1
6.7±0.3
CAV No.
0.15±0.08
1.1MAX
P=0.5±0.1
B±0.3
A±0.3
B FPC pattern
C±0.05
.2±
R0
0.45
.05
+0.3
- 0.05
1.1+0.3
- 0.05
±0
.2
R0
1.75
1.65±0.05
0.35±0.03
2.5±0.05
0.0
+0.1
0
P=0.5±0.03
5
t=0.145±0.03
B±0.05
5
±0.0
R0.2
R0
0.2
XR
MA
.2
±0
.0
5
0.05
D±0.05
0.05
E±0.05
Solder plated area: 1 to 5µm thick
Packaging code: -**,(**)
No symbol: Bag packaging (100 pieces per bag)
Unite: mm
Part Number
CL No.
DF25G-20S-0.5F(**)
DF25G-30S-0.5F(**)
DF25G-36S-0.5F(**)
Under development
Number of contacts
A
B
C
D
E
20
14.9
19.5
10.65
10.1
11.5
30
19.9
14.5
15.65
15.1
16.5
36
22.9
17.5
18.65
18.1
19.5
Note: Bag packaging (100 pieces/bag).Order by number of bags.
5
■ Plug (Fine Coaxial Ribbon Cable Type)
Note 1: Requires use of plug and shield cover.
Note 2: Requires use of dedicated assembly tools.
Contact No. 1
identification mark
6.7±0.3
CAV No.
0.15±0.08
1.1 MAX
P=0.5±0.1
B±0.3
A±0.3
CAV No.
B Cable Preparation
B±0.15
1.45±0.1
Pitch maintaining tape
Insulator Dia.
0.23±0.01
2MIN
0.7 +0.15
0
P=0.5±0.07
0.53±0.05
Grounding bar
Grounding bar 0.2±0.01
Thickness of the ground bar(0.04)
Outer jacket
3 MIN
Shield Dia.0.29mm
Laminated tape
AWG36,AWG40
0
C -0.1
Unite: mm
Part Number
DF25G-20S-0.5SD(**)
DF25G-30S-0.5SD(**)
DF25G-36S-0.5SD(**)
CL No.
Number of contacts
A
B
C
20
14.9
19.5
11
30
19.9
14.5
16
36
22.9
17.5
19
Under development
662-0012-5-**
Note: Bag packaging (100 pieces/bag).Order by number of bags.
B Applicable thin-coaxial ribbon cable
Jacket diameter (Stranded wire center conductor)
AWG#36 (7/0.05mm)
AWG#40 (7/0.03MM)
6
0.3mm to 0.4mm
Packaging code: -**,(**)
No symbol : Bags packaging
(100 pieces per bag)
■ Shield Cover (Used on Plugs terminating with FPC or Fine Coaxial Ribbon Cable.)
Contact No. 1
identification mark
6.7±0.3
A±0.3
B±0.3
0.98±0.15
Top shield cover
6.42±0.3
C±0.3
D±0.3
0.9±0.15
Bottom shield cover
Packaging code: -**,(**)
No symbol: Bag packaging
(100 pieces per bag)
Dimensions in mm
Part Number
DF25G-20S-0.5F/SD-GND(**)
DF25G-30S-0.5F/SD-GND(**)
DF25G-36S-0.5F/SD-GND(**)
CL No.
Under development
662-0011-2-**
Number of contacts
A
B
C
D
20
14.66
30
19.66
12.68
14.4
12.28
17.68
19.44
17.28
36
22.66
20.68
22.4
20.28
Note: Bag packaging (100 pieces/bag).Order by number of bags.
Complete assembly consist of Top shield cover and Bottom shield cover.
7
■ Plug (FPC Type) Termination Procedures Dedicated assembly tooling is required.
Place top shield cover over the assembly,
exercising caution as not to damage or deform any part of it.
Insert FPC as shown.
Ground surfaces
Step 1
Step 4
Signal surfaces
Actuator bar
Carefully close the built-in
retaining actuator bar.
Step 2
Slide forward the top shield cover.
Step 5
Insert the assembly (with the signal surface of FPC facing down)
in the bottom shield cover.
Excercise caution not to deform any parts of the shield cover.
5mm MIN
Completed
termination
Step 3
Distance to the first bend or fold of FPC.
Note 1: The shield cover and the plug are supplied as separate components.
Note 2: Dedicated assembly fixtures are required at each stage of the termination process.For details refer to the instruction manual supplied with
the tools.
Note 3: To protect the FPC, insertion and disconnection of the connector should be performed parallel to the mating direction.
Note 4: To protect the FPC, please do not apply excessive tension to it.
Note 5: When the FPC is to be bent, refer to FPC manufacturer for bending radius and other specific recommendations.
Note 6: The connector body can be used only one time.
■ Plug (For Fine Pitch Ribbon Coaxial Cable) Assembly Procedures
Place top shield cover over the assembly,
exercising caution as not to damage or deform any part of it.
Insert cable as shown.
Step 1
Step 4
Ground bar
Carefully close the built-in
retaining actuator bar.
Step 2
Insert the assembly (with the signal surface of FPC facing down)
in the bottom shield cover.
Excercise caution not to deform any parts of the shield cover.
Step 3
Slide forward the top shield cover.
Step 5
5mm MIN
Completed
termination
Distance to the first bend or fold of FPC.
Note 1: The shield cover and the plug are supplied as separate components.
Note 2: Dedicated assembly fixtures are required at each stage of the termination process.For details refer to the instruction manual supplied with
the tools.
Note 3: To protect the FPC, insertion and disconnection of the connector should be performed parallel to the mating direction.
Note 4: To protect the FPC, please do not apply excessive tension to it.
Note 5: When the FPC is to be bent, refer to FPC manufacturer for bending radius and other specific recommendations.
Note 6: Neither the coaxial cable nor the connector body can be used re-used.
8
B Applicable tools
Connector
DF25G-30S-0.5F
Name of Process
1 Wire forming
DF25G-36S-0.5F
(Manual)
DF25G-30S-0.5F/ID-MP
CL902-4532-8
DF25G-30S/CV-MP-A
CL902-4534-3
DF25G-30S/CV-MP-B
CL902-4533-0
2 Piercing
Placing of bottom
shield cover (A)
Placing of top
4
shield cover (B)
3
Remarks
(Manual)
DF25G-36S-0.5F/ID-MP
CL902-4526-5
DF25G-36S/CV-MP-A
CL902-4529-3
DF25G-36S/CV-MP-B
CL902-4538-4
Especially for FPC
For both FPC Plug and thin coaxial
cable Plug
For both FPC Plug and thin coaxial
cable Plug
Connector
DF25G-30S-0.5F
DF25G-36S-0.5F
DF25G-30S-0.5SD/CU-MP
CL902-4530-2
DF25G-30S-0.5SD/CAID-MP
CL902-4531-5
DF25G-30S/CV-MP-A
CL902-4534-3
DF25G-30S/CV-MP-B
CL902-4533-0
DF25G-36S-0.5SD/CU-MP
CL902-4528-0
DF25G-36S-0.5SD/CAID-MP
CL902-4527-8
DF25G-36S/CV-MP-A
CL902-4529-3
DF25G-36S/CV-MP-B
CL902-4538-4
Name of Process
1
2
3
4
Trimming the extra
cable length
Wire forming and
piercing
Placing of bottom shield
cover (A)
Placing of top shield
cover (B)
Remarks
Especially for thin coaxial cable Plug
Especially for thin coaxial cable Plug
For both FPC and thin coaxial cable
Plug
For both FPC and thin coaxial cable
Plug
Note 1: To assure that the part selection and termination procedures are correct Hirose Electric representative may be contacted at
any time.
Note 2: Only tools and fixtures recommended by Hirose Electric must be used. Use of any other tools or fixtures will void the product
warranty.
4±0.1
Ø1.
2±0.1
12±0.1
5
+0
.1
0
1.75±0.1
■ Embossed Carrier Tape Dimensions
t=0.3±0.05
C±0.1
Reel dimensions
Part number label
1±
0.8
(Ø80)
0.2
Ø330±2
Ø13±
A±0.3
B±0.1
2±0.5
Ø2
D
+2
0
E MAX
1.6±0.2
Unreeling direction
Unite: mm
Connector
Number of contacts
A
B
C
D
D
DF25L-20P-0.5H(**)
20
24
---------
11.5
24.2
30.4
DF25L-30P-0.5H(**)
30
32
28.4
14.2
32.4
38.4
DF25L-36P-0.5H(**)
36
44
40.4
20.2
44.4
50.4
Remarks
Offset type (0.7mm above the board)
9
B Usage Recommendations
1. Recommended temperature profile
IR reflow
Temperature
Preheating 150ç
250ç
Soldering
235±5ç
240ç
220ç
10 Max.
220ç Min. 10 to 30 Sec.
200ç
150ç
100ç
Preheating
Soldering
50ç
0ç
0 Sec.
50 Sec.
100 Sec.
150 Sec.
200 Sec.
Time
Note 1: Up to 2 cycles of reflow soldering are possible under the same conditions, provided that there
is a return to normal temperature between the first and second cycle.
Note 2: The temperature profile indicates the board surface temperature at the point of contacts with
the connector terminals (for surface mounted receptacle).
10
2. Recommended manual soldering
Manual soldering: 290±10ç for 3 seconds
3. Recommended screen thickness
0.15mm
4. Board warpage
Maximum of 0.03mm at the connector center, with both ends of the connector as reference points.
5. Cleaning conditions
Refer to "Nylon Connector Use Handbook".
6. Termination Conditions
Refer to "Handling Manual" of each tools.
7. Precautions
Excessive twisting when mating/un-mating may cause damage to the connectors.
B High Speed Transmission Characteristics (Typical data)
●Reflection Characteristics (Differential TDR Method)
Standard impedance: 100 ohms
Signal rise time: 250 ps
Scale Vertical axis: 100 mρ/div
Scale Horizontal axis: 500 ps/div
DF25(FPC)
DF25(Micro COAX)
100mρ
/div
100mρ
/div
Pcb
Pcb
connector
92 ohms
500ps/div
90 ohms
connector
500ps/div
●Eye Pattern
Signal speed: 2 Gbps
Scale Vertical axis: 100 mV/div
Scale Horizontal axis: 75 ps/div
DF25(FPC)
DF25(Micro COAX)
P.G.
Oscillo.
Mated Conn.
PCB
Cable
L=100mm
RF Con(50 ohms)
RF Con(50 ohms)
V=0.5V
Test Set-up
11
Similar pages