BCD AUR9807VIGD Single-cell li-ion charger ic with system power management Datasheet

NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
General Description
Features
The AUR9807 is a single-cell Li-ion charger IC with
system power management feature. It charges the
battery and power the system simultaneously. The
maximum charging current (up to 1.5A) is set by
external resistor for fast charging. The output
voltage for the system is regulated to a nominal
value (three different versions available: 4.4V, 5V or
6V); the actual value of the output voltage depends
on the input voltage from the adapter, the charging
current and the system loading. With the decrease of
the input voltage or the increase of the system
loading current, the output voltage drops. When the
output voltage drops to a predetermined value
(VAPM-REG), the Active Power Management function
is activated and tries to maintain the output voltage
at VAPM-REG; the AUR9807 will suffice the system
loading with first priority and reduce the charging
current temporarily, i.e. under heavy load condition,
the AUR9807 charges the battery with the remaining
available current to keep the output voltage at VAPM.
In this manner, the charge and discharge cycle of the
battery can be reduced.
It is possible that the AUR9807 fails to maintain the
output voltage at VAPM-REG; for example, when the
system loading current exceeds the capability of the
current-limiting AC adapter. In this scenario, the
output voltage drops to the battery voltage, and the
system is allowed to draw current from the battery.
The AUR9807 is available in QFN-4.5×3.5-20
package.
•
•
•
•
•
•
•
•
•
•
•
QFN Package
Active Power Management (APM) for
Simultaneously Powering the System and
Charging the Battery
Total Current Supported Up to 2 Amperes
(System Loading Having Higher Priority on the
Budget)
Automatic Power Source Selection (AC Adapter
or Battery)
40mΩ Power Path for the Battery to Supply the
System Power Efficiently
Junction Temperature Detection and Thermal
Regulation During Charging Process
External LED Indicating Charger and Power
Good Status as Well as Fault Condition
Thermal, Short-Circuit, and Reverse Current
Protection
Short-Circuit Protection in the Low Power
Consumption Sleep Mode
SYSOFF Function to Cut Off the Path Between
the System and the Battery
Built-in Over Voltage Protection up to 18V
Applications
•
•
•
•
Battery-Powered Devices or Equipment
Mobile Phones, Digital Cameras and MP3
Players
Radios, Other Hand-Held Games and Instruments
Solar Power System
QFN-4.5×3.5-20
Figure 1. Package Type of AUR9807
AUR9807
Document number: DS37580 Rev. 1 - 3
1 of 23
www.diodes.com
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
Pin Configuration
GND
Pin 1 Mark
VREF
D Package
(QFN-4.5×3.5-20)
1
20
STAT1
2
19
GND
STAT2
3
18
/PG
IN
4
17
OUT
BAT
5
16
OUT
BAT
6
15
OUT
ISET2
7
14
TMR
MODE
8
13
APM
CE
9
12
TS
10
11
ISET1
SYSOFF
Exposed
Pad
Figure 2. Pin Configuration of AUR9807 (Top View)
AUR9807
Document number: DS37580 Rev. 1 - 3
2 of 23
www.diodes.com
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
Pin Description
Pin Number
I/O
Pin Name
Function
1
O
VREF
Internal reference; VREF output capacitor not required, but
one with a value of 0.1μF is recommended.
2
O
STAT1
Charge status flag 1 (open-drain)
3
O
STAT2
Charge status flag 2 (open-drain)
4
I
IN
5,6
I/O
BAT
7
I
ISET2
8
I
MODE
9
I
CE
10
I/O
ISET1
11
I
SYSOFF
12
I/O
TS
13
I
APM
14
I/O
TMR
15 , 16 , 17
O
OUT
System output
18
O
/PG
Power-good status flag (open-drain)
19 , 20
I
GND
AUR9807
Document number: DS37580 Rev. 1 - 3
Chip input voltage
Battery connection; charging or discharging all through this
pin
USB mode total current selection (High=450mA, Low=
90mA) and AC mode charge current selection (High=Full
current, Low=half current)
Set AUR9807 in AC(High) or USB(Low) mode
Chip enable (active high)
Set the maximum charging current
Cut off the power path between the battery and the output pin
Battery Temperature sensing
Active Power Management set point ※ no need for
capacitors
Timer program by external resistor connected to this pin.
Tying TMR and VREF together to disable the safety timer
Chip Ground
3 of 23
www.diodes.com
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
Functional Block Diagram
IN
4
1
3.3V
Short-Circuit
Recovery
VREF
15, 16, 17
Q1
OUT
VOUT
UVLO
Fault
Recovery
Power Source
Selection
VISENSE
100mA
500mA
VSET
BAT
Short-Circuit
Recovery
ISENSE
Q2
10
VI(ISET1)
5, 6
VBAT
VOUT
VOUT(REG)
SYSOFF
GND
TMR
APM
ISET1
BAT
11
VBAT
VBAT(REG)
19, 20
VI(ISET1)
VSET
14
VSET
VAPM
Oscillator
13
TJ
TJ(REG)
VBAT
VOUT
IAMP
1V
VHTF
ITS
TS
12
AC Charge Enable
Thermal
Shutdown
1V
BAT Charge Enable
VLTF
500mA/100mA
Fast Precharge
MODE
CE
Power Source Selection
8
9
VBAT
VRCH
Charge
Control Timer
and Display
Logic
1C - 500mA
7
ISET2
C/S - 100mA
18
/PG
Recharge
2
VBAT
VLOWV
VI(ISET1)
VTERM
Precharge
Termation
VBAT
VIN
3
STAT1
STAT2
Sleep
Figure 3. Functional Block Diagram of AUR9807
AUR9807
Document number: DS37580 Rev. 1 - 3
4 of 23
www.diodes.com
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
Ordering Information
AUR9807
Circuit Type
D: QFN-4.5x3.5-20
Output Voltage
VF: 4.4V, CV Mode
DF: 4.4V, Done
VI: 5V, CV Mode
DI: 5V, Done
VS: 6V, CV Mode
DS: 6V, Done
G: Green
CV mode: After charge done, charger will stay in constant
voltage mode until time out.
Done: After charge done, charger will shut down until the
battery voltage drops below the battery recharge threshold.
Package
QFN-4.5x3.5-20
Temperature
Range
-40 to 85C
Output Voltage
Part Number
Marking ID
Packing
Type
4.4V, CV Mode
AUR9807VFGD
A9807VFG
Tape & Reel
4.4V, Done
AUR9807DFGD
A9807DFG
Tape & Reel
5V, CV Mode
AUR9807VIGD
A9807VIG
Tape & Reel
5V, Done
AUR9807DIGD
A9807DIG
Tape & Reel
6V, CV Mode
AUR9807VSGD
A9807VSG
Tape & Reel
6V, Done
AUR9807DSGD
A9807DSG
Tape & Reel
BCD Semiconductor's Pb-free products, as designated with "G" in the part number, are RoHS compliant and
green.
AUR9807
Document number: DS37580 Rev. 1 - 3
5 of 23
www.diodes.com
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
Absolute Maximum Ratings (Note 1)
Parameter
Supply Input Voltage
Input Voltage
Symbol
Value
Unit
VIN
VBAT, VCE, VAPM, V/PG,
VMODE, VOUT, VISET1,
VISET2, VSTAT1, VSTAT2,
VTS
VREF
-0.3 to 18
V
-0.3 to 7
V
-0.3 to VOUT+0.3
V
VTMR
-0.3 to VOUT+0.3
V
IIN
3.5
A
IOUT
4
A
IBAT
-4 to 1.5
A
IREF
30
mA
I/PG, ISTAT1, ISTAT2
15
mA
JA
52
°C/W
TSTG
-65 to 150
°C
TJ
-40 to 150
°C
300
°C
Input Current
Output Current
Output Source Current
(In Regulation at 3.3V VREF)
Output Sink Current
Thermal Resistance
(Junction to Ambient)
Storage Temperature
Junction Temperature
Lead Temperature
(Soldering, 10 Seconds)
ESD (Human Body Model)
VHBM
2000
V
ESD (Machine Model)
VMM
200
V
Note 1: Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to
the device. These are stress ratings only, and functional operation of the device at these or any other conditions
beyond those indicated under “Recommended Operating Conditions” is not implied. Exposure to “Absolute
Maximum Ratings” for extended periods may affect device reliability.
Recommended Operating Conditions
Parameter
Symbol
AUR9807DSGD, AUR9807VSGD
Supply Voltage
AUR9807DFGD,AUR9807VFGD,
AUR9807DIGD, AUR9807VIGD
VIN
Input Current
IIN
Operating Junction Temperature Range
TOP
AUR9807
Document number: DS37580 Rev. 1 - 3
6 of 23
www.diodes.com
Min
Max
Unit
4.35
6.3
V
4.35
5.5
V
2
A
125
°C
-40
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
Electrical Characteristics
TA=25oC, VIN is within the recommended range, unless otherwise specified.
Parameter
Symbol
Test Condition
Active Supply Current
IIN(SPLY)
Sleep Mode Current into
BAT Pin
IBAT(SLP)
Input
Pin
Current
IIN(STDBY)
Standby
BAT Pin Standby Current
IBAT(STDBY)
Charge
BAT
IBAT(TERM)
Done
Current,
Q1,Q2 DROP-OUT VOLTAGE
IN to OUT Dropout
VDO(IN-OUT)
Voltage
BAT to OUT Dropout
VDO(BAT-OUT)
Voltage
VOLTAGE REGULATION
Regulation VOUT
VOUT(REG)
9807VF 9807DF
Regulation VOUT
VOUT(REG)
9807VI 9807DI
Regulation VOUT
VOUT(REG)
9807VS 9807DS
APM REGULATION
Min
Typ
Max
Unit
VIN>4.35V
VIN<VBAT,
2.6V<VBAT<VBAT(REG)
No load at OUT pin
VIN<6V, Total current flow
into IN pin with CE pin
low; no load
Total current flow into
BAT pin with input source
present and CE pin low
Current flows into BAT
pin after the termination of
the charging process
1.1
2
mA
2.5
5
μA
200
μA
45
65
μA
1
5
μA
MODE=High , IIN=1A
300
475
mV
VBAT> 4V , IBAT=1A
40
100
mV
VIN>4.4V+VDO(IN-OUT)
4.4
4.5
V
VIN>5V+VDO(IN-OUT)
4.9
5.1
V
VIN>6V+VDO(IN-OUT)
6
6.3
V
3.8
V
μA
APM Set Point
VAPM-SET
VAPM-SET<VOUT
2.6
APM Current Source
IAPM-SET
Input present
95
100
105
VAPM-REG=VAPM-SET x SF
1.139
1.15
1.162
VOUT<
VBAT–
60mV
APM Scale Factor
SF
BATTERY SUPPLEMENT MODE
Run Battery Supplement
Mode
VBSUP1
VBAT>2V
Escape
Battery
Supplement Mode
VBSUP2
VBAT>2V
Precharge to Fast-charge
Transition Voltage
VLOWV
Voltage on BAT
Precharge Current Range
IPRECHG
V
VOUT>
VBAT–
20mV
V
3.1
V
150
mA
CHARGING-PRECHARGE
AUR9807
Document number: DS37580 Rev. 1 - 3
2.9
10
7 of 23
www.diodes.com
3
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
Electrical Characteristics (Continued)
TA=25oC, VIN is within the recommended range, unless otherwise specified.
Parameter
Symbol
Precharge Set Voltage
VPRECHG
Test Condition
tFALL=100ns,
De-glitch Time Between
10mV overdrive,
Fast
Charge
and
tDGLF
VBAT
decreasing
below
Precharge Transition
threshold
CHARGING-CURRENT REGULATION
Fast Charge Current
ICHG
VBAT>VLOWV, Mode=High
Range
BAT to OUT Pull-up
RPBAT
VBAT<1V
Battery Charge Current
VSET
Voltage on ISET1
Set Voltage(1)
100mA<ICHG<1.5A
Charge
Current
Set
KSET
Factor
10mA<ICHG<100mA
Min
Typ
Max
Unit
225
250
275
mV
22.5
100
1000
ms
1500
mA
Ω
1000
2.4
2.5
2.6
V
375
425
450
300
450
600
USB MODE INPUT CURRENT LIMIT
USB Input Current Range
IUSB
ISET2=High
400
ISET2=Low
80
500
90
100
mA
CHARGING VOLTAGE REGULATION
Battery-charge-voltage
Battery Charge Voltage
Regulation Accuracy
4.2
VBAT(REG)
TA=25°C
CHARGE TERMINATION DETECTION
VBAT>VRCH,
Charge Done Detection
ITERM
ITERM=(KSET x VTERM)/
Current
RSET
VBAT>VRCH, Mode=High
Charge Done Set Voltage,
VTERM
Measured on ISET1
VBAT>VRCH, Mode=Low
TEMPERATURE SENSE COMPARATORS
High
Voltage,
Low
VLTF
Temp fault at VTS>VLTF
Temperature Threshold
Low Voltage , High
VHTF
Temp fault at VTS<VHTF
Temperature Threshold
Current
Source
for
ITS
Temperature Sense
BATTERY RECHARGE THRESHOLD
Recharge
Voltage
Threshold
V
-0.5
0.5
%
-1
1
%
10
150
mA
230
250
270
95
100
130
95
mV
2.5
V
0.5
V
100
105
μA
VBAT(RE VBAT(RE VBAT(RE
VRCH
V
G)
G)
G)
-0.125
-0.1
-0.075
(1) For half-charge rate, VSET is 1.25V.
AUR9807
Document number: DS37580 Rev. 1 - 3
8 of 23
www.diodes.com
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
Electrical Characteristics (Continued)
TA=25oC, VIN is within the recommended range, unless otherwise specified.
Parameter
Symbol
Test Condition
Low-level
Output
Saturation Voltage
VOL
IOL=5mA,
requiring
an
external pull-up resistor>
1kΩ
Input Leakage Current
ILKG
Min
Typ
Max
Unit
0.25
V
5
μA
4
6
ms
1.1
STAT1, STAT2, AND /PG
1
ISET2, CE
CE Pin Hold-off Time
tCE-HLDOF
CE fall low only
F
Low-level Input Voltage
VIL
0
High-level Input Voltage
CE Pin
Low-level Input Current
CE Pin
High-level Input Current
ISET2 Pin
Low-level Input Current
ISET2 Pin
High-level Input Current
MODE
VIH
1.5
IIL1
-1
Mode Pin
Low-level Input Voltage
Mode Pin
High-level Input Voltage
Mode Pin
Low-level Input Current
TIMERS
IIH1
IIH2
VISET2=VIN
VIH
Falling Hi→Low;
280kΩ±10% applied when
low
Input RMODE sets external
hysteresis
IIL
KTMR
External Resistor Limits
RTMR
Precharge Timer
tPRECHG
Timer Fault Recovery
Pull-up from OUT to BAT
RFAULT
Time
Out
Factor1
Extension
KEXT1
Time
Out
Factor2
Extension
Document number: DS37580 Rev. 1 - 3
μA
VISET2=0.4V
Timer Set Factor
AUR9807
1
IIL2
VIL
KEXT2
V
-20
40
0.975
1
VIL+
0.01
1.025
V
VIL+
0.024
V
μA
-1
tCHG=KTMR x RTMR
0.313
30
0.115
x
tCHG
0.36
0.414
s/Ω
kΩ
0.125
x
tCHG
100
0.135
x
tCHG
1
The actual charge current less
than 50% of maximum fast
charge current
The actual charge current less
than 25% of maximum fast
charge current
9 of 23
www.diodes.com
s
kΩ
2
4
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
Electrical Characteristics (Continued)
TA=25oC, VIN is within the recommended range, unless otherwise specified.
Parameter
Symbol
Test Condition
CHARGER SLEEP THRESHOLDS
Sleep-mode
Entry
VSLPENT
Threshold
Sleep-mode
Exit
VSLPEXIT
Threshold
DE-GLITCH TIME
De-glitch
Time
for
Charge Done Detection,
Temperature
Fault,
tDEG
Recharge
and
Sleep
Mode Detection
START-UP CONTROL BOOT-UP
Temperature Trip
Max
VBAT
+0.195
18.75
tBOOT-UP
TSHTDWN
Typ
VBAT
+0.125
On the first application
of input low
SWITCHING POWER SOURCE TIMING
When input applied.
Switching Power Source
tSW-BAT
Measure from: [/PG: Lo
from Input to Battery
→ Hi to IIN>5 mA ]
THERMAL SHUTDOWN REGULATION
Boot-up Time
Min
120
150
TJ (Q1 and Q3 only)
150
TJ (Q1 and Q3 only)
25
Unit
mV
ms
180
ms
50
μs
Thermal Hysteresis
Temperature Regulation
Limit
UVLO
TJ(REG)
TJ (Q2)
110
Under-voltage Lockout
VUVLO
2.45
2.5
2.65
V
Input Power Detection
Threshold
VIN(DT)
Decreasing VIN
Input power detected
when
VIN>VBAT + VIN(DT)
VBAT=3.6V
VIN: 3.5V → 4V
55
80
130
mV
Hysteresis
VREF OUTPUT
Output
Regulation
Voltage
Regulation Accuracy
VREF
Output Current
IREF
On Resistance
RDS(ON)
Output Capacitance
AUR9807
Document number: DS37580 Rev. 1 - 3
Active only if ADP or
USB is present
-5
OUT to VREF
COUT
10 of 23
www.diodes.com
°C
130
27
mV
3.3
V
+5
%
20
mA
50
Ω
1
μF
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
Electrical Characteristics (Continued)
TA=25oC, VIN is within the recommended range, unless otherwise specified.
SHORT CIRCUIT PROTECTION
Short-circuit
Recovery
Between BAT to OUT
IN to OUT Short-circuit
Protection
Output
Short-circuit
Detection
Threshold,
Power-on
Output
Short-circuit
Detection
Threshold,
Supplement mode
(VBAT – VOUT)>VOUT(SC2)
Indicates Short-circuit
Deglitch
Time,
Supplement Mode Short
Circuit
Maximum Short-current
for VBAT>VOUT
IOSH1
Pull-up source from
BAT to OUT for
short-circuit recovery
VOUT<VBAT–200mV
10
mA
RSHAC
VOUT<1V
500
Ω
VOUT(SC1)
VIN>VUVLO and
VIN>VBAT + VIN(DT)
0.9
1
1.1
V
VOUT(SC2)
VBAT>2.5V
160
200
240
mV
tDGL(SC2)
ISHORT(2)
μs
512
VBAT>2.5V
9
A
(2) For short current>ISHORT , short-protection may not work due to avalanche breakdown phenomenon.
Typical Performance Characteristics
Figure 4. Output Voltage vs. Output Current
AUR9807
Document number: DS37580 Rev. 1 - 3
Figure 5. Output Voltage vs. Charge Current
11 of 23
www.diodes.com
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
Typical Performance Characteristics (Continued)
VOUT
2V/div
VIN
2V/div
ICHG
0.5A/div
Time 20ms/div
Figure 6. Charge Current vs. Input Voltage
Figure 7. Power On
VIN
2V/div
VOUT
2V/div
VOUT
2V/div
VIN
2V/div
ICHG
1A/div
ICHG
0.5A/div
VMODE
2V/div
VSYSOFF
2V/div
Time 1ms/div
Time 200s/div
Figure 8. SYSOFF Floating
AUR9807
Document number: DS37580 Rev. 1 - 3
Figure 9. MODE Pin Pull Low
12 of 23
www.diodes.com
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
Typical Performance Characteristics (Continued)
VIN
2V/div
VOUT
2V/div
ICHG
0.5A/div
VIN
2V/div
VOUT
2V/div
ICHG
0.5A/div
VISET2
2V/div
VISET2
2V/div
Time 40s/div
Time 400s/div
Figure 10. ISET2 Pin Pull High
Figure 11. ISET2 Pin Pull Low
VIN
2V/div
VOUT
2V/div
ICHG
0.5A/div
VMODE
2V/div
Time 40s/div
Figure 12. MODE Pin Pull High
AUR9807
Document number: DS37580 Rev. 1 - 3
13 of 23
www.diodes.com
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
Power Flow
AC Adapter (or USB)
IN
OUT
Q1
VDC
VDC
-
System
Q2
40 mΩ
+
OUTREF
BAT
AUR9807
The AUR9807 selects the power source automatically.
In the absence of the input source (AC adapter or USB),
the battery is chosen to power the system. Under this
circumstance, the AUR9807 consumes less than 5μ
Ampere; the power path resistance from the battery to
the system is only 40mΩ (3); all these guarantee a high
efficiency and elongate the battery discharge time. With
this stringent sleep current budget (<5μA), the
AUR9807 is still able to detect an output short
condition and cuts off the power path between the
battery and the system under short condition.
directly, current limiting phenomenon occurs through
Adaptive Power Management in response to the output
voltage drop. The resistor connected to ISET1 pin sets
the maximum charging current. This maximum
charging current can be halved by pulling down the
ISET2 pin. In USB mode, the AUR9807 will limit the
total current within 450mA (ISET2=High) or 90mA
(ISET2=Low). The maximum charging current is still
set by the resistor connected to ISET1 pin; however,
because of this current limiting feature, the actual
charging current is usually less than 450mA (or 90mA).
With the input power present, the MODE pin sets the
AUR9807 in adapter mode or USB mode. In adapter
mode, the AUR9807 does not limit the total current
(3) Q2 design value is 40mΩ.
Power Source Selection and Charge Current Setting
MODE Pin
Level
AC Adapter
Loading Power
Source
Charge Current Setting
Yes
USB
ISET1, limitation depends on ISET2 setting
No
Battery
N/A
Yes
AC Adapter
ISET1, half charging rate by setting ISET2 to low
No
Battery
N/A
Low
High
AUR9807
Document number: DS37580 Rev. 1 - 3
14 of 23
www.diodes.com
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
Charge Function Descriptions
Charge Flow
Charge current = ICHG
Current
VBAT = 4.2V
Voltage
VBAT=Recharge threshold
VBAT=3V
Charge Current = 0.1 x ICHG
Charge Done
Timer Timeout
Time
Precharge
Constant Current
Phase
Constant Voltage
Phase
Maximum Charging Current Setting
MODE=High ISET2=High
MODE=High
MODE=Low
ISET2=Low
I CHG 
I CHG 
VSET  K SET
, VSET, max  2.5
R SET
VSET  K SET
, VSET, max  1.25
R SET
VSET  K SET
ISET2=High/L I
, VSET, max  2.5
CHG 
ow
R SET
AUR9807
Document number: DS37580 Rev. 1 - 3
15 of 23
www.diodes.com
Charge
Done
Recharge
Process
Pre-charge and Charge Done
Current Setting
I PRECHG 
I CHG,max
;
10
I CHG,max
; AC M ode
10
I
I PRECHG  CHG,max
20
I CHG,max
I TERM 
; AC M ode
20
I
I PRECHG  CHG,max
10
I
I TERM  CHG,max ; USB M ode
25
I TERM 
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
Charge Function Descriptions (Continued)
The maximum charging current, the pre-charge
current and charge done current setting are given in
the above table. The charging process begins with a
pre-charge phase; when the battery voltage reaches
the pre-charge threshold VLOWV, the charger enters
the constant current mode. At this stage, the charger
tries to charge the battery with the maximum
charging current (a constant); however, the actual
charging current may be lower due to Active Power
Management activated by large system loading or
insufficient input current capability. The thermal
fold-back mechanism also reduces the actual
charging current when the junction temperature is
over 110°C. The battery voltage rises gradually with
the constant current entering the battery.
When the battery voltage reaches VBAT(REG), the
charger enters the constant voltage mode. At this
stage, the charger keeps the battery voltage at
VBAT(REG) with a decreasing charging current. When
the charging current drops below the charge done
current setting, nominally the charging process is
complete (this can be observed from the external
indicator). Depending on different versions, after the
charge done status indicated, the charger will stop
providing charging current completely or stay in
constant voltage mode till time out. When the battery
voltage drops below the recharge threshold, a new
charge cycle begins.
Example:
With a RSET=1kΩ, the maximum charging current is
about 1A for ISET2=High and 0.5A for ISET2=Low.
The pre-charge current IPRECHG is 100mA. The charge
done current setting is 100mA for AC mode and
40mA for USB mode. Note the absolute values of
pre-charge current and charge done current setting do
not vary with ISET2.
Power Source Selecting
AC Adapter
IN
OUT
Q1
VDC
-
System
Q2
40 mΩ
+
OUTREF
BAT
AUR9807
i.
ii.
iii.
iv.
VIN<VBAT : VOUT=VBAT–VDO(BAT-OUT)
VBAT<VIN<VOUT(REG) : VOUT=VIN–VDO(IN-OUT)
VOUT(REG) +VDO(IN-OUT)<VIN<6V: VOUT=VOUT(REG)
6V<VIN: VOUT =VBAT–VDO(BAT-OUT)
The AUR9807 selects power source automatically
depending on the voltage present at the input. When
VIN is lower than VBAT, the battery is responsible to
power the system. The output voltage VOUT is VBAT –
VDO(BAT-OUT). When the input voltage VIN is higher
than VBAT and lower than 6V, the input source is used
to supply the system power; the output voltage
depends on VIN. When VIN is lower than VOUT(REG),
AUR9807
Document number: DS37580 Rev. 1 - 3
the output voltage VOUT is VIN–VDO(IN-OUT); when VIN
is high enough, which means that V IN>(VOUT(REG)+
VDO(IN-OUT)), the output voltage is regulated at
VOUT(REG). When the input voltage VIN is higher than
6V, the current path between IN and OUT is cut off to
protect the chip; AUR9807 therefore selects the
Battery as the power source; the output voltage VOUT
is then VBAT–VDO(BAT-OUT).
16 of 23
www.diodes.com
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
Charge Function Descriptions (Continued)
Active Power Management (APM)
When the output voltage is higher than VAPM-REG, the
input source is capable of providing the charging
current (set by RSET) and output current (determined by
system loading) simultaneously. When the output
voltage goes down and reaches VAPM-REG due to an
increasing loading, AUR9807 starts to reduce the
charging current and tries to keep the output voltage at
VAPM-REG. Because AUR9807 uses the remaining
available current to charge the battery, the charging
current can be estimated as Isupply max – IOUT. In AC mode,
the Isupply max is determined by the driving capability of
the AC adapter and AUR9807 itself (usually the
limiting factor is the AUR9807, and Isupply max is about
2A). The Isupply max is determined by the ISET2 setting in
USB mode (Isupply max is about 450mA with ISET2 high,
and Isupply max is about 90mA with ISET2 low).
 AC MODE (MODE=HIGH)
i.
VAPM-REG<VOUT : Normal Mode; ICHG determined
by RSET
ii.
VBAT<VOUT<VAPM-REG : APM mode ; ICHG= Isupply
–I
max OUT
iii. VOUT<VBAT : BAT supply mode
 USB 500 MODE (MODE=LOW ,
ISET2=HIGH)
i.
VAPM-REG<VOUT: Normal Mode; ICHG determined
by RSET
ii.
VBAT<VOUT<VAPM-REG : APM mode; ICHG =
450mA – IOUT
iii. VOUT<VBAT: BAT supply mode
 USB 100 MODE (MODE=LOW ,
ISET2=LOW)
i.
VAPM-REG<VOUT : Normal Mode; ICHG determined
by RSET
ii.
VBAT<VOUT<VAPM-REG : APM mode; ICHG=
90mA–IOUT
iii. VOUT<VBAT : BAT supply mode
When the loading current keeps increasing and exceeds
Isupply max, the AUR9807 can not prevent the output
voltage dropping below VAPM-REG even the charging
current is reduced to zero. When the output voltage
drops below the battery voltage, the battery helps to
supply the loading current and keeps the output voltage
roughly at VBAT. At this situation, we have:
The active power management feature adjusts the
charging current to resist the output voltage drop due to
heavy system loading or insufficient input driving
capability. In the extreme situation, the charging current
flow would be reversed (the battery helps to supply the
system power). The active power management
regulation voltage VAPM-REG is given by:
VAPM-REG = IAPM-SET×RAPM ×SF(4)
IOUT = Isupply max+IBAT(5)
(4)
(5)
RAPM<38kΩ: VAPM-REG=IAPM-SET×RAPM×SF
RAPM>41kΩ: The VAPM-REG is set to
predetermined fixed value (4.26V)
IBAT=(VBAT–VOUT) / (40mΩ Power Path
Resistance)
a
Battery Temperature Protection
AUR9807
BAT
Li Battery
1µF
100µA
LOGIC UNIT
VHTF
NTC
TS
VLTF
AUR9807
Document number: DS37580 Rev. 1 - 3
17 of 23
www.diodes.com
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
Charge Function Descriptions (Continued)
The AUR9807 interrupts the charging process when the
battery temperature is out of normal range. It provides a
100μA sensing current to the negative-temperature
coefficient resistor (on the battery side) through the TS
pin. The battery protection is achieved by constantly
monitoring the voltage at the TS pin. When this voltage
is higher than VLTF (nominally 2.5V) or lower than
VHTF (nominally 0.5V), an under-temperature or
over-temperature condition is detected. For an usual
103AT-type NTC resistor, the corresponding
temperature range is between 0°C and 45°C. The
normal battery temperature range can be modified by
adjusting the NTC resistor or by adding extra resistor
network
between
the
TS pin
and
the
negative-temperature coefficient resistor. The charging
process would resume after the battery temperature
goes back within the normal range.
Charge Timeout Setting
The charge timeout setting is programmed by the
resistor RTMR connected between the TMR and ground
pin. The timeout setting is given by:
Once the abnormal condition is removed (high
temperature or heavy loading), the charging current
resumes the maximum values (set by RSET), and the
time out counter will operate in normal rate.
Charge Status Indicator
Status
Pre-charge
Constant current and constant
voltage charge
Charge done
Fault condition (time out,
sleep mode, or OTP)
STAT1
ON
STAT2
ON
ON
OFF
OFF
ON
OFF
OFF
The open drain pins STAT1 and STAT2 provides the
information about the charger status when the CE pin
(chip enable) is set to high. The various charger status
and the corresponding STAT1 and STAT2 levels are
given in the above Table. Connect these pins to the host
processor or LEDS to indicate the charger status.
Short Circuit Protection
tCHG = KTMR ×RTMR
A suggested 36kΩ RTMR gives a 3.6 hrs timeout setting
because the nominal value of KTMR is 0.36 sec/Ω. In the
actual charging process, the charging duration is
elongated if the charging current can not reach the
maximum current setting (again this relates to system
loading and environment temperature); therefore, it is
possible that the charging process is still on progress
while the 3.6 hrs timeout limit has been reached. To
circumvent this problem, the actual charging current is
monitored and the clock rate of the timer counter is
halved if the charging current is less than 50% of the
maximum fast charging current. This is equivalent to
modify the timeout setting temporarily by the following
equation:
tCHG = KEXT1 x KTMR ×RTMR, where KEXT1=2
If the actual charging current is less than one fourth the
maximum fast charging current, the time out counter
rate is reduced to 25%. The temporary timeout setting
is given by:
AUR9807 provides short circuit protection for both the
input and the battery. When VIN is larger than VBAT, AC
adapter (or USB port) is chosen as the power source. If
the output voltage is lower than 1V (VOUT(SC1)) for more
than tDGL(SC), a short circuit condition is detected; the
power path between the input and the output will be cut
off. The charging process will be interrupted. A 500Ω
resistor is used to pull up the output voltage; if the load
at the output is removed, the output voltage can be
pulled up and the short circuit condition is dissolved.
Similarly, when the battery is chosen as the power
source, an output voltage lower than the battery voltage
by 200mV (VOUT(SC2)) longer than tDGL(SC) will trigger
the short circuit protection mechanism (this
corresponds to a 5A loading current). A 10mA current
source is used to pull up the output and detect the
removal of the short condition. The power consumption
is less than 5μA under the battery supply mode;
however, AUR9807 is still able to monitor the output
voltage and detect a short circuit condition with this
limiting current budget.
SYSOFF Function
tCHG = KEXT2 x KTMR ×RTMR, where KEXT2=4
AUR9807
Document number: DS37580 Rev. 1 - 3
The SYSOFF function is used to cut off the power path
between the battery and the output. This means the
18 of 23
www.diodes.com
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
Charge Function Descriptions (Continued)
charger function can be disabled by pulling up the
SYSOFF pin; in this mode, the AUR9807 is almost a
regulator to power the system. Because the power path
is cut off, the output voltage will drop to zero when the
input source is removed, the battery will not be used to
power the system. The SYSOFF pin is pulled high
internally; therefore, this pin should be pulled to ground
for normal operation.
Recharge Process
Elimination
and
Timer
Fault
If timeout occurs and the battery voltage is higher
than the recharge threshold, the charger will stay in
the charge done mode until the battery voltage drops
below the recharge threshold. Once the battery
voltage drops below the recharge threshold, a new
AUR9807
Document number: DS37580 Rev. 1 - 3
charge cycle starts.
If timeout occurs and the battery voltage is lower
than the recharge threshold, the charger will indicate
a fault condition and an internal resistor between
output and battery will try to pull up the battery
voltage. If the internal resistor is unable to pull up the
battery voltage to the recharge threshold, the charger
will stay in fault condition. Once the battery voltage
is higher than the recharge threshold, the charger
removes the pull-up resistor, leaves the fault
condition and stay in the charge done mode
temporarily. The charger then waits the battery
voltage to drop below the recharge threshold and
starts a new charge cycle.
19 of 23
www.diodes.com
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
PC Board Layout Considerations
It is important to pay special attention to the PCB
layout. The following provides some guidelines.
1. To obtain optimal performance, the decoupling
capacitor from the input terminal to GND and the
output filter capacitor from OUT to GND should be
placed as close as possible to the AUR9807, with
short trace runs to both signal and GND pins.
2. All low-current GND connections should be kept
separate from the high-current charge or discharge
paths from the battery. Use a single-point ground
technique incorporating both the small signal
ground path and the power ground path.
3. The high-current charge paths into IN and from the
BAT and OUT pins must be sized appropriately for
the maximum charge current in order to avoid
voltage drops in these traces.
STAT1
VOUT
VOUT
+5V
JP5
3
2
1
R1 1k
H
LED1 - Green
STAT2
H
R2 1k
LED2 - Red
/PG
R16
1k
D1
5.1V ZENER
R3 1k
LED3 - Green
VOUT
C1
0.1μF
C4
10μF/16V
VIN
C5
/opt
U1
VIN
C6
/opt
1
2
3
4
5
6
7
8
9
10
C2
10μF/35V
VBAT
C7
/opt
C3
1μF
VREF
STAT1
STAT2
IN
BAT
BAT
ISET2
MODE
CE
ISET1
GND
GND
/PG
OUT
OUT
OUT
TMR
APM
TS
SYSOFF
R13
/opt
20
19
18
17
16
15
14
13
12
11
TP4
TP3
JP1
TS
R6
100k
L
ISET2
H
L
MODE
H
3
2
1
JP2
R12
20k
R10
10k
TP2
ISET1
3
2
1
R11
27k
APM
TP1
R5
100k
R15
50k
TMR
AUR9807
R4
100k
R14
30k
R8
1k
R9
10k
R7
100k
3
2
1
JP3
L
CE
H
L
SYS_OFF
H
3
2
1
JP4
H
Figure 13. The Evaluation Board Schematic
AUR9807
Document number: DS37580 Rev. 1 - 3
20 of 23
www.diodes.com
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
PC Board Layout Considerations (Continued)
Figure 14. Top Side View of The Evaluation Board
Figure 15. Bottom Side View of The Evaluation Board
AUR9807
Document number: DS37580 Rev. 1 - 3
21 of 23
www.diodes.com
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
20
VREF
1
Typical Application
GND
Adapter or USB
10μF
2
STAT1
GND
19
3
STAT2
/PG
18
4
IN
OUT
17
5
BAT
OUT
16
6
BAT
OUT
15
7
ISET2
TMR
14
BATTERY
SYSTEM
10μF
1μF
RTMR
8
MODE
9
CE
APM
13
TS
12
RAPM
NTC
11
ISET1
10
RSET
SYSOFF
Control Signals and
Status Indicators
Figure 16. Typical Application of AUR9807
AUR9807
Document number: DS37580 Rev. 1 - 3
22 of 23
www.diodes.com
October 2014
© Diodes Incorporated
NOT RECOMMENDED FOR NEW DESIGN
Data Sheet
Single-cell Li-Ion Charger IC with System Power Management AUR9807
Mechanical Dimensions
QFN-4.5×3.5-20
Pin 1 Mark
Unit: mm(inch)
0.300(0.012)
0.500(0.020)
1.500(0.059)
BSC
N20
N1
N19
4.500(0.177)
BSC
N2
2.950(0.116)
3.100(0.122)
N12
N9
N11
3.500(0.138)
BSC
N10
1.950(0.077)
2.100(0.083)
0.700(0.027)
0.800(0.031)
0.180(0.007)
0.300(0.012)
0.500(0.020)
BSC
0.200(0.008)
REF
0.000(0.000)
0.050(0.002)
AUR9807
Document number: DS37580 Rev. 1 - 3
23 of 23
www.diodes.com
October 2014
© Diodes Incorporated
BCD Semiconductor Manufacturing Limited
http://www.bcdsemi.com
IMPORTANT NOTICE
BCD Semiconductor Manufacturing Limited reserves the right to make changes without further notice to any products or specifications herein. BCD Semiconductor Manufacturing Limited does not assume any responsibility for use of any its products for any
IMPORTANT NOTICE
IMPORTANT
NOTICE
particular purpose, nor does BCD Semiconductor Manufacturing Limited assume any liability arising out of the application or use
of any its products or circuits. BCD Semiconductor Manufacturing Limited does not convey any license under its patent rights or
BCD Semiconductor
BCD
Semiconductor Manufacturing
Manufacturing Limited
Limited reserves
reserves the
the right
right to
to make
make changes
changes without
without further
further notice
notice to
to any
any products
products or
or specifispecifiother rights nor the rights of others.
cations herein.
cations
herein. BCD
BCD Semiconductor
Semiconductor Manufacturing
Manufacturing Limited
Limited does
does not
not assume
assume any
any responsibility
responsibility for
for use
use of
of any
any its
its products
products for
for any
any
particular
particular
purpose,
purpose,
nor
nor
does
does
BCD
BCD
Semiconductor
Semiconductor
Manufacturing
Manufacturing
Limited
Limited
assume
assume
any
any
liability
liability
arising
arising
out
out
of
of
the
the
application
application
or
or
use
use
MAIN SITE
ofHeadquarters
any its
any
its products
products or
or circuits.
circuits. BCD
BCD Semiconductor
Semiconductor Manufacturing
Manufacturing
Limited
does not
does
not convey
convey any
any license
license under
under its
its patent
patent rights
rights or
or
-of
- Wafer Limited
Fab
BCD
(Shanghai)
Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd.
other
other
rights Micro-electronics
rights
nor the
nor
the rights
rightsLimited
of others.
of
others.
No. 1600, Zi Xing Road, Shanghai ZiZhu Science-based Industrial Park, 200241, P. R.C.
Tel: +86-021-2416-2266, Fax: +86-021-2416-2277
MAIN SITE
SITE
MAIN
REGIONAL
SALES Manufacturing
OFFICE
- Headquarters
BCD
Semiconductor
Limited
800 Yishan Road, Shanghai 200233, China
Tel: +021-6485-1491, Fax: +86-021-5450-0008
- Wafer
FabSemiconductor Manufacturing Limited
BCD
BCD
Semiconductor
Manufacturing Limited
Shanghai
SIM-BCD
Semiconductor Manufacturing Co., Ltd.
Shenzhen
Office
Taiwan
Office
(Taipei)
- Wafer
Fab
- IC Design
Group
No.
1600, Zi
Xing Road,
Shanghai ZiZhu
Science-basedCo.,
Industrial
Park, 200241,
China
Yi
Shan Road,
Shanghai
200233,
China
Shanghai
SIM-BCD
Semiconductor
Manufacturing
Ltd., Shenzhen
Office
BCD800
Semiconductor
(Taiwan)
Company
Limited
Shanghai
SIM-BCD
Semiconductor
Manufacturing
Limited
Advanced
Analog
Circuits
(Shanghai)
Corporation
Tel:
Fax: +86-21-24162277
Tel: +86-21-6485
1491,
0008Dist.,
Unit
A
1203,Skyworth
Bldg.,
Gaoxin
3F, No.17,
Lane
171,
Sec.
2,
Jiu-Zong
Rd.,Shanghai
Nei-Hu
Taipei(114),
Taiwan, R.O.C
800,+86-21-24162266,
YiRoom
Shan Road,
Shanghai
200233,
ChinaAve.1.S., Nanshan District
8F,
Zone
B, 900,
YiFax:
Shan+86-21-5450
Road,
200233,
China
Shenzhen
518057,1491,
ChinaFax: +86-21-5450 0008
Tel: +886-2-2656
2808
Tel: +86-21-6485
Tel: +86-21-6495
9539, Fax: +86-21-6485 9673
REGIONAL
SALES OFFICE
Tel: +86-0755-8660-4900,
Fax: +86-0755-8660-4958
Fax: +886-2-2656-2806/26562950
Shenzhen OfficeSALES OFFICE
Taiwan Office
USA Office
REGIONAL
Shanghai
SIM-BCD
Semiconductor Manufacturing Co., Ltd., Shenzhen Office
Semiconductor
BCD Office
Semiconductor Corp.
Taiwan
Office
(Hsinchu)
USABCD
Office
Korea Office USA
Shenzhen
Office
Taiwan
Office (Taiwan) Company Limited
Unit
ASemiconductor
Room
1203, Skyworth
Gaoxin
Ave.1.S., Nanshan
Shenzhen,
4F,Semiconductor
298-1,
Guang
Road,(Taiwan)
Nei-Hu District,
Taipei,
30920Semiconductor
Huntwood
Ave.Corporation
Hayward,
BCD
(Taiwan)Bldg.,
Company
Limited
BCD
Corp.
BCD
Semiconductor
Limited Korea
office.
Shanghai
SIM-BCD
Semiconductor
Manufacturing
Co., Ltd.District,
Shenzhen
Office
BCDRui
Semiconductor
Company
Limited
BCD
China
Taiwan
CADigital-Empire
94544,
USA Ave.
8F,
No.176,Analog
Sec. 2, Gong-Dao
5th Road, Corporation
East District Shenzhen Office
48460
Kato
CARoad,
94538,
USA District,
Room
101-1112,
II, 486
Sin-dong,
Advanced
Circuits (Shanghai)
4F,Road,
298-1,Fremont,
Rui Guang
Nei-Hu
Taipei,
30920
Huntwood
Hayward,
Tel:
+86-755-8826
7951
+886-2-2656
2808
Tel
:94544,
+1-510-324-2988
HsinChu
300, Taiwan,
R.O.C 3rd Fuzhong Road, Futian District, Shenzhen 518026, China
Tel:Tel:
+1-510-668-1950
Yeongtong-Gu,
Suwon-city,
Gyeonggi-do, Korea
Room
E, City
5F, Noble
Center, No.1006,
Taiwan
CA
U.S.A
Fax:
+86-755-8826
7865
Fax:
+886-2-2656
2806
Fax:
+1-510-324-2788
Tel:
+886-3-5160181,
Fax:
+886-3-5160181
Fax:
+1-510-668-1990
Tel:
+82-31-695-8430
Tel: +86-755-8826 7951
Tel: +886-2-2656 2808
Tel : +1-510-324-2988
Fax: +86-755-8826 7865
Fax: +886-2-2656 2806
Fax: +1-510-324-2788
Similar pages