I N D U C T O R S July 2013 Inductors for High Frequency Multilayer Ceramic MLK series MLK0603 MLK1005 0603 [0201 inch]* 1005 [0402 inch] * Dimensions Code JIS[EIA] (1/14) I N D U C T O R S REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 001-01 / 20130707 / inductor_high-frequency_mlk_en.fm (2/14) I N D U C T O R S Inductors for High Frequency Circuits Product compatible with RoHS directive Halogen-free Compatible with lead-free solders Multilayer Ceramic Overview of the MLK Series FEATURES With the adoption of a giga-spiral laminated structure, a self-resonant frequency higher than that of the MLG structure can be obtained, while the decrease of Q in the GHz band is limited. Monolithic structure is formed using a multilayering and sintering process with ceramic and conductive materials for high-frequency. There is no directivity. APPLICATION Smart phones, tablet terminals, high frequency modules (PAs, VCOs, FEMs , etc.), Bluetooth, W-LAN, UWB, tuners, automotive equipment (MLK1005) and other high frequency circuits for the mobile communication industry PART NUMBER CONSTRUCTION MLK Series name 0603 L×W×H Dimensions (mm) 0603 0.6×0.3×0.3 1005 1.0×0.5×0.5 L Characteristics L S 1N1 J Inductance (μH) 1N1 1.1 11N 11 R10 100 Inductance tolerance S ±0.3nH J ±5% T □□□ Packaging style Internal code T Taping OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Package quantity Operating Storage Type temperature temperature (pieces/reel) （°C） （°C） MLK0603 –55 to +125 –55 to +125 15000 MLK1005 –55 to +125 –55 to +125 10000 The Storage temperature range is for after the circuit board is mounted. Individual weight （mg） 0.2 1 RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. • All specifications are subject to change without notice. 001-01 / 20130707 / inductor_high-frequency_mlk_en.fm (3/14) I N D U C T O R S Overview of the MLK Series RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150°C 180°C Time t1 60 to 120s Soldering Temp. Time T3 t2 230°C 30 to 60s Peak Temp. T4 250 to 260°C Time t3 10s max. • All specifications are subject to change without notice. 001-01 / 20130707 / inductor_high-frequency_mlk_en.fm (4/14) I N D U C T O R S MLK series MLK0603 Type 0.30±0.03 SHAPE & DIMENSIONS 0.15±0.05 0.15±0.05 0.30±0.03 0.6±0.03 Dimensions in mm 0.3 RECOMMENDED LAND PATTERN 0.25 0.3 0.25 Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20130707 / inductor_high-frequency_mlk_en.fm (5/14) I N D U C T O R S MLK series MLK0603 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (nH) 1.0 1.1 1.2 1.3 1.5 1.6 1.8 2.0 2.2 2.4 2.7 3.0 3.3 3.6 3.9 4.3 4.7 5.1 5.6 6.2 6.8 7.5 8.2 9.1 10 12 15 18 22 27 33 Tolerance ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% Self-resonant L measuring Q measuring frequency Q frequency frequency (GHz) min. (MHz) (MHz) min. typ. 100 6 300 12.0 17.1 100 6 300 11.0 17.1 100 6 300 11.0 16.1 100 6 300 10.0 15.8 100 6 300 10.0 14.9 100 6 300 10.0 14.3 100 6 300 10.0 13.8 100 6 300 9.0 12.6 100 6 300 9.0 12.5 100 6 300 8.5 11.4 100 6 300 8.5 10.9 100 6 300 8.0 10.6 100 6 300 8.0 10.5 100 6 300 8.0 9.9 100 6 300 8.0 9.8 100 6 300 7.5 9.5 100 6 300 7.5 9.5 100 6 300 6.5 8.8 100 6 300 6.5 8.5 100 6 300 6.0 8.3 100 6 300 6.0 8.1 100 6 300 6.0 7.7 100 6 300 6.0 7.9 100 6 300 5.5 7.4 100 6 300 5.5 7.5 100 6 300 5.0 6.9 100 6 300 4.5 6.6 100 6 300 4.0 5.8 100 6 300 3.5 5.3 100 6 300 3.0 4.6 100 6 300 2.8 4.4 DC resistance (: ) max. 0.20 0.22 0.22 0.24 0.24 0.27 0.27 0.30 0.30 0.35 0.35 0.40 0.40 0.45 0.45 0.50 0.50 0.60 0.60 0.65 0.65 0.70 0.70 0.80 0.80 1.00 1.10 1.30 1.60 1.70 1.80 typ. 0.09 0.10 0.11 0.12 0.12 0.13 0.14 0.15 0.17 0.17 0.18 0.20 0.22 0.22 0.25 0.28 0.28 0.28 0.30 0.34 0.34 0.36 0.41 0.42 0.48 0.54 0.66 0.85 1.02 1.09 1.21 Rated current (mA) max. Part No.* 300 300 300 300 300 300 300 300 300 300 300 200 200 200 200 200 200 200 200 200 200 200 200 200 200 150 150 100 100 100 100 MLK0603L1N0ST□□□ MLK0603L1N1ST□□□ MLK0603L1N2ST□□□ MLK0603L1N3ST□□□ MLK0603L1N5ST□□□ MLK0603L1N6ST□□□ MLK0603L1N8ST□□□ MLK0603L2N0ST□□□ MLK0603L2N2ST□□□ MLK0603L2N4ST□□□ MLK0603L2N7ST□□□ MLK0603L3N0ST□□□ MLK0603L3N3ST□□□ MLK0603L3N6ST□□□ MLK0603L3N9ST□□□ MLK0603L4N3ST□□□ MLK0603L4N7ST□□□ MLK0603L5N1ST□□□ MLK0603L5N6ST□□□ MLK0603L6N2ST□□□ MLK0603L6N8JT□□□ MLK0603L7N5JT□□□ MLK0603L8N2JT□□□ MLK0603L9N1JT□□□ MLK0603L10NJT□□□ MLK0603L12NJT□□□ MLK0603L15NJT□□□ MLK0603L18NJT□□□ MLK0603L22NJT□□□ MLK0603L27NJT□□□ MLK0603L33NJT□□□ The " □□□ " of the Part Number contains the internal code. ○ Measurement equipment Measurement item Product No. L, Q 4291B+16197A Self-resonant frequency 8720C DC resistance Type-7561 ＊ Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Yokogawa • All specifications are subject to change without notice. 001-01 / 20130707 / inductor_high-frequency_mlk_en.fm (6/14) I N D U C T O R S MLK series MLK0603 Type ELECTRICAL CHARACTERISTICS L, Q FREQUENCY CHARACTERISTICS TABLE L(nH)typ. 500MHz 0.9 1.0 1.1 1.2 1.3 1.4 1.6 1.8 2.0 2.1 2.4 2.7 3.0 3.2 3.5 3.8 4.2 4.6 5.0 5.5 6.2 6.7 7.4 8.2 9.0 10.8 13.5 16.2 19.8 24.4 29.7 800MHz 0.9 1.0 1.0 1.1 1.3 1.4 1.6 1.7 1.9 2.1 2.4 2.6 2.9 3.1 3.4 3.8 4.2 4.5 5.0 5.5 6.1 6.6 7.3 8.1 8.9 10.6 13.4 16.1 19.7 24.4 29.7 1.8GHz 0.9 0.9 1.0 1.1 1.3 1.4 1.6 1.7 1.9 2.1 2.4 2.6 2.9 3.1 3.5 3.8 4.2 4.5 5.0 5.5 6.2 6.7 7.5 8.3 9.2 11.0 13.9 17.0 20.9 27.2 33.4 2.0GHz 0.9 0.9 1.0 1.1 1.3 1.4 1.6 1.7 1.9 2.1 2.4 2.6 3.0 3.1 3.5 3.8 4.2 4.6 5.0 5.6 6.2 6.8 7.6 8.4 9.3 11.2 14.2 17.4 21.5 28.6 35.1 2.4GHz 0.9 0.9 1.0 1.1 1.3 1.4 1.6 1.7 2.0 2.1 2.4 2.7 3.0 3.2 3.5 3.9 4.3 4.7 5.1 5.7 6.4 7.0 7.8 8.6 9.6 11.6 14.8 18.4 22.8 31.7 39.3 Q typ. 500MHz 10 9 9 9 9 9 9 9 10 9 10 9 10 9 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 9 800MHz 12 11 12 12 12 12 11 12 12 12 13 12 13 11 13 12 13 12 12 12 13 12 13 12 13 12 12 12 12 12 11 1.8GHz 19 17 18 18 18 18 17 17 19 18 19 18 19 17 19 18 19 18 18 18 19 18 19 18 18 18 17 16 16 15 14 2.0GHz 20 18 19 19 19 19 18 18 20 19 20 19 20 18 20 19 20 19 19 19 20 19 20 18 19 18 18 17 16 15 14 2.4GHz 22 20 21 21 21 21 20 20 22 20 22 21 22 19 22 20 22 21 21 20 22 20 21 20 20 20 19 18 17 14 13 Part No.* MLK0603L1N0ST□□□ MLK0603L1N1ST□□□ MLK0603L1N2ST□□□ MLK0603L1N3ST□□□ MLK0603L1N5ST□□□ MLK0603L1N6ST□□□ MLK0603L1N8ST□□□ MLK0603L2N0ST□□□ MLK0603L2N2ST□□□ MLK0603L2N4ST□□□ MLK0603L2N7ST□□□ MLK0603L3N0ST□□□ MLK0603L3N3ST□□□ MLK0603L3N6ST□□□ MLK0603L3N9ST□□□ MLK0603L4N3ST□□□ MLK0603L4N7ST□□□ MLK0603L5N1ST□□□ MLK0603L5N6ST□□□ MLK0603L6N2ST□□□ MLK0603L6N8JT□□□ MLK0603L7N5JT□□□ MLK0603L8N2JT□□□ MLK0603L9N1JT□□□ MLK0603L10NJT□□□ MLK0603L12NJT□□□ MLK0603L15NJT□□□ MLK0603L18NJT□□□ MLK0603L22NJT□□□ MLK0603L27NJT□□□ MLK0603L33NJT□□□ The " □□□ " of the Part Number contains the internal code. ○ Measurement equipment Product No. Manufacturer 4291B+16197A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130707 / inductor_high-frequency_mlk_en.fm (7/14) I N D U C T O R S MLK series MLK0603 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE) 1000 100 33N 27N 22N Inductance(nH) 18N 15N 12N 10 10N 8N2 6N8 5N6 4N7 3N9 3N3 2N7 2N2 1N8 1N5 1N2 1 1N0 0 10 100 1000 10000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16197A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130707 / inductor_high-frequency_mlk_en.fm (8/14) I N D U C T O R S MLK series MLK0603 Type ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE) 30 3N3 6N8 2N7 3N9 4N7 1N0 1N2 8N2 1N5 2N2 10N 5N6 1N8 12N 20 15N 18N Q 22N 27N 33N 10 0 10 100 1000 10000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16197A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130707 / inductor_high-frequency_mlk_en.fm (9/14) I N D U C T O R S MLK series MLK1005 Type 0.50±0.10 SHAPE & DIMENSIONS 0.1min. 0.1min. 0.50±0.10 1.00±0.10 Dimensions in mm 0.5 RECOMMENDED LAND PATTERN 0.5 0.4 0.5 Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20130707 / inductor_high-frequency_mlk_en.fm (10/14) I N D U C T O R S MLK series MLK1005 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L Q min. (nH) 1.0 1.1 1.2 1.3 1.5 1.6 1.8 2.0 2.2 2.4 2.7 3.0 3.3 3.6 3.9 4.3 4.7 5.1 5.6 6.2 6.8 7.5 8.2 9.1 10 12 15 18 22 27 33 39 47 56 68 82 100 110 120 130 150 160 180 200 220 240 270 300 330 Tolerance ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% 5 5 5 5 6 6 6 6 6 6 6 6 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 Q measuring frequency (MHz) 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 Self-resonant frequency (GHz) min. typ. 12.0 16.9 11.5 14.8 11.0 14.4 10.0 12.6 9.5 12.2 9.0 11.9 8.5 10.9 8.3 10.0 8.0 9.6 7.8 9.5 7.5 9.1 7.2 8.5 7.0 8.3 6.8 8.1 6.5 7.8 6.3 7.4 6.0 6.9 5.8 7.0 5.7 6.7 5.6 6.5 5.5 6.3 5.0 6.0 5.0 6.0 4.8 5.9 4.7 5.2 4.3 5.3 4.0 4.8 4.0 4.7 3.5 4.4 3.0 3.9 2.5 3.5 2.0 3.1 1.8 3.0 1.5 2.6 1.4 2.4 1.3 2.2 1.1 1.9 1.1 2.0 1.1 1.9 1.1 1.8 1.1 1.7 1.1 1.7 1.1 1.6 1.1 1.5 1.0 1.4 1.0 1.3 0.9 1.2 0.9 1.2 0.85 1.1 DC resistance (: ) max. 0.10 0.12 0.12 0.15 0.15 0.17 0.17 0.18 0.18 0.20 0.20 0.22 0.22 0.25 0.25 0.28 0.28 0.30 0.30 0.35 0.35 0.38 0.38 0.42 0.42 0.47 0.50 0.60 0.70 0.80 0.90 1.00 1.20 1.30 1.50 1.80 2.20 2.70 3.00 3.30 5.00 5.20 6.00 6.20 6.20 6.50 6.50 7.50 8.00 typ. 0.05 0.05 0.05 0.06 0.06 0.06 0.07 0.08 0.08 0.09 0.10 0.10 0.11 0.11 0.12 0.13 0.13 0.15 0.15 0.18 0.18 0.20 0.21 0.23 0.23 0.27 0.33 0.38 0.46 0.53 0.59 0.65 0.74 0.84 1.01 1.39 1.60 1.89 2.08 2.28 3.58 3.79 4.28 4.56 4.54 4.84 4.78 5.37 5.82 Rated current (mA) max. Part No. 500 500 500 500 500 500 500 500 500 500 500 400 400 400 400 400 400 400 400 400 400 350 350 350 350 350 300 250 200 200 200 200 200 200 150 150 100 100 100 100 80 80 80 70 70 70 70 70 70 MLK1005S1N0△T□□□ MLK1005S1N1△T□□□ MLK1005S1N2△T□□□ MLK1005S1N3△T□□□ MLK1005S1N5△T□□□ MLK1005S1N6△T□□□ MLK1005S1N8△T□□□ MLK1005S2N0△T□□□ MLK1005S2N2△T□□□ MLK1005S2N4△T□□□ MLK1005S2N7△T□□□ MLK1005S3N0△T□□□ MLK1005S3N3△T□□□ MLK1005S3N6△T□□□ MLK1005S3N9△T□□□ MLK1005S4N3△T□□□ MLK1005S4N7△T□□□ MLK1005S5N1△T□□□ MLK1005S5N6△T□□□ MLK1005S6N2△T□□□ MLK1005S6N8△T□□□ MLK1005S7N5△T□□□ MLK1005S8N2△T□□□ MLK1005S9N1△T□□□ MLK1005S10N△T□□□ MLK1005S12N△T□□□ MLK1005S15N△T□□□ MLK1005S18N△T□□□ MLK1005S22N△T□□□ MLK1005S27N△T□□□ MLK1005S33N△T□□□ MLK1005S39N△T□□□ MLK1005S47N△T□□□ MLK1005S56N△T□□□ MLK1005S68N△T□□□ MLK1005S82N△T□□□ MLK1005SR10△T□□□ MLK1005SR11△T□□□ MLK1005SR12△T□□□ MLK1005SR13△T□□□ MLK1005SR15△T□□□ MLK1005SR16△T□□□ MLK1005SR18△T□□□ MLK1005SR20△T□□□ MLK1005SR22△T□□□ MLK1005SR24△T□□□ MLK1005SR27△T□□□ MLK1005SR30△T□□□ MLK1005SR33△T□□□ The " △ " of the Part Number contains the inductance tolerance code, S(±0.3nH) or J(±5%). The " □□□ " of the Part Number contains the internal code. ○ Measurement equipment Measurement item Product No. L, Q 4291B+16193A Self-resonant frequency 8720C DC resistance Type-7561 ＊ Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Yokogawa • All specifications are subject to change without notice. 001-01 / 20130707 / inductor_high-frequency_mlk_en.fm (11/14) I N D U C T O R S MLK series MLK1005 Type ELECTRICAL CHARACTERISTICS L, Q FREQUENCY CHARACTERISTICS TABLE L(nH)typ. 500MHz 0.9 1.0 1.1 1.2 1.4 1.5 1.7 1.9 2.0 2.2 2.5 2.8 3.1 3.4 3.7 4.0 4.4 4.8 5.3 5.8 6.4 7.1 7.7 8.6 9.4 11.3 14.2 17.0 20.8 25.6 31.4 37.2 45.0 53.7 65.5 79.3 97.1 107.8 118.0 127.5 149.4 160.5 181.1 202.8 225.7 248.3 290.0 323.1 358.9 800MHz 0.9 1.0 1.1 1.2 1.4 1.5 1.7 1.8 2.0 2.2 2.5 2.8 3.1 3.3 3.6 4.0 4.4 4.8 5.2 5.8 6.4 7.0 7.7 8.6 9.4 11.3 14.2 17.1 20.9 25.9 31.9 38.1 46.2 55.4 68.4 83.6 103.2 115.9 127.8 139.5 166.0 179.4 204.1 231.9 266.8 299.6 386.0 432.6 493.1 1.8GHz 0.9 1.0 1.1 1.2 1.4 1.5 1.7 1.9 2.0 2.2 2.5 2.8 3.1 3.4 3.7 4.1 4.5 4.9 5.4 6.0 6.6 7.4 8.1 9.1 10.0 12.1 15.3 18.6 23.0 29.8 37.6 48.9 60.6 76.7 105.6 142.7 199.4 2.0GHz 0.9 1.0 1.1 1.2 1.4 1.5 1.7 1.9 2.0 2.3 2.6 2.9 3.1 3.5 3.7 4.2 4.6 5.0 5.5 6.2 6.7 7.6 8.3 9.3 10.2 12.4 15.8 19.2 23.9 31.5 40.2 2.4GHz 0.9 1.0 1.1 1.2 1.4 1.5 1.7 1.9 2.1 2.3 2.6 2.9 3.2 3.5 3.8 4.3 4.7 5.1 5.7 6.4 7.0 7.9 8.6 9.7 10.7 13.0 16.8 20.6 25.8 35.7 Q typ. 500MHz 16 16 15 17 15 17 16 16 15 16 17 18 16 17 17 17 17 17 17 18 17 18 19 18 19 19 18 18 18 18 18 17 18 17 17 16 15 16 16 14 16 16 16 15 15 14 14 14 13 800MHz 20 20 18 20 19 21 21 20 19 20 22 22 20 22 21 22 22 22 22 23 22 23 23 23 23 23 23 23 23 23 23 21 21 21 20 19 18 18 18 16 17 18 17 17 15 15 12 12 12 1.8GHz 30 32 28 33 29 34 32 32 29 32 33 35 31 33 32 34 33 33 33 34 32 34 34 34 34 34 33 32 32 30 29 24 24 22 18 15 13 2.0GHz 32 35 30 35 31 36 33 34 31 34 35 36 32 35 33 35 35 35 34 35 33 36 36 36 35 35 34 33 33 30 29 2.4GHz 36 39 33 39 34 40 37 38 34 38 39 41 36 39 37 39 38 38 38 39 36 38 38 38 38 37 35 34 34 28 Part No.* MLK1005S1N0△T□□□ MLK1005S1N1△T□□□ MLK1005S1N2△T□□□ MLK1005S1N3△T□□□ MLK1005S1N5△T□□□ MLK1005S1N6△T□□□ MLK1005S1N8△T□□□ MLK1005S2N0△T□□□ MLK1005S2N2△T□□□ MLK1005S2N4△T□□□ MLK1005S2N7△T□□□ MLK1005S3N0△T□□□ MLK1005S3N3△T□□□ MLK1005S3N6△T□□□ MLK1005S3N9△T□□□ MLK1005S4N3△T□□□ MLK1005S4N7△T□□□ MLK1005S5N1△T□□□ MLK1005S5N6△T□□□ MLK1005S6N2△T□□□ MLK1005S6N8△T□□□ MLK1005S7N5△T□□□ MLK1005S8N2△T□□□ MLK1005S9N1△T□□□ MLK1005S10N△T□□□ MLK1005S12N△T□□□ MLK1005S15N△T□□□ MLK1005S18N△T□□□ MLK1005S22N△T□□□ MLK1005S27N△T□□□ MLK1005S33N△T□□□ MLK1005S39N△T□□□ MLK1005S47N△T□□□ MLK1005S56N△T□□□ MLK1005S68N△T□□□ MLK1005S82N△T□□□ MLK1005SR10△T□□□ MLK1005SR11△T□□□ MLK1005SR12△T□□□ MLK1005SR13△T□□□ MLK1005SR15△T□□□ MLK1005SR16△T□□□ MLK1005SR18△T□□□ MLK1005SR20△T□□□ MLK1005SR22△T□□□ MLK1005SR24△T□□□ MLK1005SR27△T□□□ MLK1005SR30△T□□□ MLK1005SR33△T□□□ The " △ " of the Part Number contains the inductance tolerance code, S(±0.3nH) or J(±5%). The " □□□ " of the Part Number contains the internal code. ○ Measurement equipment Product No. Manufacturer 4291B+16193A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130707 / inductor_high-frequency_mlk_en.fm (12/14) I N D U C T O R S MLK series MLK1005 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE) 1000 R33 R27 R22 R12 R10 82N 56N R18 68N R15 47N 39N 100 33N 27N 22N 18N Inductance(nH) 15N 12N 10N 10 8N2 6N8 5N6 4N7 3N9 3N3 2N7 2N2 1N8 1N5 1N2 1 0 10 1N0 100 1000 10000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16193A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130707 / inductor_high-frequency_mlk_en.fm (13/14) I N D U C T O R S MLK series MLK1005 Type ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE) 50 2N7 1N8 1N0 4N7 3N9 40 5N6 1N5 3N3 6N8 12N 10N 15N 8N2 1N2 2N2 18N 22N Q 30 27N 20 33N R15 R22 R18 R27 R33 10 39N 47N 68N 82N R10 56N R12 0 10 100 1000 10000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16193A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130707 / inductor_high-frequency_mlk_en.fm (14/14) I N D U C T O R S MLK series Packaging Style REEL DIMENSIONS ø60min. 1.0 2.0±0.5 8.4 +2.0 –0.0 ø13±0.2 14.4max. ø21±0.8 ø180±2.0 Dimensions in mm 3.5±0.05 Cavity Type MLK0603 MLK1005 A 0.5 max. 0.8 max. B 0.38±0.05 0.67±0.1 C 0.68±0.05 1.15±0.1 C 8.0±0.3 Sprocket hole 1.5 +0.1 –0.0 1.75±0.1 TAPE DIMENSIONS A B 4.0±0.1 2.0±0.05 160min. Taping 2.0±0.05 200min. Drawing direction 300min. • All specifications are subject to change without notice. 001-01 / 20130707 / inductor_high-frequency_mlk_en.fm