ATMEL AT60142HT-DD15MSV Rad hard 512k x 8 5v tolerant very low power cmos sram Datasheet

Features
• Operating Voltage: 3.3V, 5V tolerant
• Access Time:
•
•
•
•
•
•
•
•
•
•
– 17 ns
– 15 ns
Very Low Power Consumption
– Active: 610 mW (Max) @ 17 ns(1), 540 mW (Max) @ 25 ns
– Standby: 3.3 mW (Typ)
Wide Temperature Range: -55 to +125°C
TTL-Compatible Inputs and Outputs
Asynchronous
Designed on 0.25 µm Radiation Hardened Process
No Single Event Latch Up below LET Threshold of 80 MeV/mg/cm2@125°C
Tested up to a Total Dose of 300 krads (Si) according to MIL-STD-883 Method 1019
500 Mils Wide FP36 Package
ESD better than 2000V
Quality Grades:
– QML-Q or V
– ESCC
Note:
1. 650 mW (Max) @ 15 ns
Description
The AT60142HT is a very low power CMOS static RAM organized as 512K x 8 bits.
Rad Hard
512K x 8
5V Tolerant
Very Low Power
CMOS SRAM
AT60142HT
Atmel brings the solution to applications where fast computing is as mandatory as low
consumption, such as aerospace electronics, portable instruments, or embarked
systems.
Utilizing an array of six transistors (6T) memory cells, the AT60142HT combines an
extremely low standby supply current (Typical value = 1 mA) with a fast access time at
15 ns over the full military temperature range. The high stability of the 6T cell provides
excellent protection against soft errors due to noise.
The AT60142HT is processed according to the methods of the latest revision of the
MIL PRF 38535 or ESCC 9000.
It is produced on a radiation hardened 0.25 µm CMOS process.
7841A–AERO–10/09
1
AT60142HT
Block Diagram
A0
A1
A2
A3
A4
CS
I/O1
I/O2
Vcc
GND
I/O3
I/O4
WE
A5
A6
A7
A8
A9
Note:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
36 - pin -Flatpack - 500 Mils
Pin Configuration
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
NC
A18
A17
A16
A15
OE
I/O8
I/O7
GND
Vcc
I/O6
I/O5
A14
A13
A12
A11
A10
NC
NC pins are not bonded internally. So, they can be connected to GND or Vcc.
2
7841A–AERO–10/09
Pin Description
Table 1. Pin Names
Name
Description
A0 - A18
Address Inputs
I/O1 - I/O8
Data Input/Output
CS
Chip Select
WE
Write Enable
OE
Output Enable
Vcc
Power Supply
GND
Ground
Table 2. Truth Table(1)
CS
WE
OE
Inputs/Outputs
Mode
H
X
X
Z
Deselect / Power-down
L
H
L
Data Out
Read
L
L
X
Data In
Write
L
H
H
Z
Output Disable
Note:
3
1. L=low, H=high, X= L or H, Z=high impedance.
AT60142HT
7841A–AERO–10/09
AT60142HT
Electrical Characteristics
Absolute Maximum Ratings*
Supply Voltage to GND Potential: ....................... -0.5V + 4.6V
*NOTE:
Stresses beyond those listed under "Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress
rating only and functional operation of the
device at these or any other conditions
beyond those indicated in the operational
sections of this specification is not implied.
Exposure between recommended DC
operating and absolute maximum rating
conditions for extended periods may
affect device reliability.
Voltage range on any input: ...................... GND -0.5V to 7.0V
Voltage range on any ouput: ..................... GND -0.5V to 4.6V
Storage Temperature: ................................. -65°C to + 150°C
Output Current from Output Pins: ................................ 20 mA
Electro Statics Discharge Voltage: ............................ > 2000V
(MIL STD 883D Method 3015)
Military Operating Range
Operating Voltage
Operating Temperature
3.3 + 0.3V
-55⋅C to + 125⋅C
Recommended DC Operating Conditions
Parameter
Description
Min
Typ
Max
Unit
Vcc
Supply voltage
3.0
3.3
3.6
V
GND
Ground
0.0
0.0
0.0
V
Note:
VIL
Input low voltage
GND - 0.3
0.0
0.8
V
VIH
Input high voltage
2.2
–
5.5(1)
V
1. 5.8V in transient conditions.
Capacitance
Parameter
Description
Min
Typ
Max
Unit
Cin(1)
Input capacitance
–
–
12
pF
Cout(1)
Output capacitance
–
–
12
pF
Note:
1. Guaranteed but not tested.
4
7841A–AERO–10/09
DC Parameters
DC Test Conditions
TA = -55°C to + 125°C; Vss = 0V; VCC = 3.0V to 3.6V
Parameter
Description
Minimum
Typical
Maximum
Unit
IIX (1)
Input leakage current
-1
–
1
μA
IOZ(1)
Output leakage current
-1
–
1
μA
IIH(2) at 5.5V
Input Leakage Current
–
–
2
μA
Output Leakage Current
–
–
1.5
μA
VOL(3)
Output low voltage
–
–
0.4
V
VOH(4)
Output high voltage
2.4
–
–
V
IOZH(2) at 5.5V
1.
GND < VIN < VCC, GND < VOUT < VCC Output Disabled.
2.
3.
4.
VIN = 5.5V, VOUT = 5.5V, Output Disabled.
VCC min. IOL = 6 mA
VCC min. IOH = -4 mA.
Consumption
AT60142HT-17
AT60142HT-15
Unit
Value
Standby Supply Current
–
2.5
2.5
mA
max
Standby Supply Current
–
2
2
mA
max
Dynamic Operating Current
15 ns
17 ns
25 ns
50 ns
1 µs
170
150
75
10
180
170
150
75
10
mA
max
Dynamic Operating Current
15 ns
17 ns
25 ns
50 ns
1 µs
145
130
120
100
150
145
130
120
100
mA
max
Description
ICCSB (1)
ICCSB1 (2)
ICCOP(3) Read
ICCOP(4) Write
1.
2.
3.
4.
5
TAVAV/TAVAW
Test Condition
Symbol
CS >VIH
CS > VCC - 0.3V
F = 1/TAVAV, Iout = 0 mA, WE = OE = VIH, VIN = GND/VCC, VCC max.
F = 1/TAVAW, Iout = 0 mA, WE = VIL, OE = VIH , VIN = GND/VCC, VCC max.
AT60142HT
7841A–AERO–10/09
AT60142HT
Data Retention Mode
Atmel CMOS RAM's are designed with battery backup in mind. Data retention voltage
and supply current are guaranteed over temperature. The following rules insure data
retention:
1. During data retention chip select CS must be held high within VCC to VCC -0.2V.
2. Output Enable (OE) should be held high to keep the RAM outputs high impedance, minimizing power dissipation.
3. During power-up and power-down transitions CS and OE must be kept between
VCC + 0.3V and 70% of VCC.
4. The RAM can begin operation > tR ns after VCC reaches the minimum operation
voltages (3V).
Figure 1. Data Retention Timing
Data Retention Characteristics
Parameter Description
Min
Typ TA = 25⋅C
Max
Unit
VCCDR
VCC for data retention
2.0
–
–
V
tCDR
Chip deselect to data retention time
0.0
–
–
ns
tR
Operation recovery time
–
–
ns
ICCDR (2)
1.
2.
Data retention current
tAVAV
–
(1)
0.700
1.5
(AT60142HT-15)
1.5
(AT60142HT-17)
mA
TAVAV = Read cycle time.
CS = VCC, VIN = GND/VCC.
6
7841A–AERO–10/09
AC Characteristics
Temperature Range:.................................................................................... -55 +125°C
Supply Voltage:............................................................................................... 3.3 +0.3V
Input Pulse Levels: .................................................................................... GND to 3.0V
Input Rise and Fall Times:......................................................................3ns (10 - 90%)
Input and Output Timing Reference Levels: ........................................................... 1.5V
Output Loading IOL/IOH:..............................................................................See Figure 2
Figure 2. AC Test Loads Waveforms
Write Cycle
Symbol
Parameter
Unit
Value
TAVAW
Write cycle time
17
15
ns
min
TAVWL
Address set-up time
0
0
ns
min
TAVWH
Address valid to end of write
8
8
ns
min
TDVWH
Data set-up time
7
7
ns
min
TELWH
CS low to write end
12
10
ns
min
(1)
TWLQZ
Write low to high Z
7
6
ns
max
TWLWH
Write pulse width
8
8
ns
min
TWHAX
Address hold from end of write
0
0
ns
min
TWHDX
Data hold time
0
0
ns
min
3
3
ns
min
TWHQX
Notes:
7
AT60142HT-17 AT60142HT-15
(1)
Write high to low Z
1. Parameters guaranteed, not tested, with output loading 5 pF. (See “AC Test Loads
Waveforms” on page 7.)
AT60142HT
7841A–AERO–10/09
AT60142HT
Write Cycle 1.
WE Controlled, OE High During Write
E
Write Cycle 2.
WE Controlled, OE Low
E
Write Cycle 3.
CS Controlled
E
Note:
The internal write time of the memory is defined by the overlap of CS Low and W LOW.
Both signals must be activated to initiate a write and either signal can terminate a write
by going in active mode. The data input setup and hold timing should be referenced to
the active edge of the signal that terminates the write.
Data out is high impedance if OE= VIH.
8
7841A–AERO–10/09
Read Cycle
Symbol
Parameter
AT60142HT-17
AT60142HT-15
Unit
Value
TAVAV
Read cycle time
17
15
ns
min
TAVQV
Address access time
17
15
ns
max
TAVQX
Address valid to low Z
5
5
ns
min
TELQV
Chip-select access time
17
15
ns
max
TELQX
CS low to low Z(1)
5
5
ns
min
TEHQZ
CS high to high Z(1)
7
6
ns
max
TGLQV
Output Enable access time
8
6
ns
max
TGLQX
OE low to low Z(1)
2
2
ns
min
TGHQZ
OE high to high Z (1)
6
5
ns
max
Note:
1. Parameters guaranteed, not tested, with output loading 5 pF. (See “AC Test Loads
Waveforms” on page 7.)
Read Cycle nb 1
Address Controlled (CS = OE = VIL, WE = VIH)
Read Cycle nb 2
Chip Select Controlled (WE = VIH)
9
AT60142HT
7841A–AERO–10/09
AT60142HT
Ordering Information
Part Number
Temperature Range
AT60142HT-DS17M-E
(2)
Speed
Package
Flow
Engineering Samples
25°C
17 ns/5V tol.
FP36.5 grounded lid
-55° to +125°C
17 ns/5V tol.
FP36.5 grounded lid
Mil Level B
AT60142HT-DS17MSV(2)
-55° to +125°C
17 ns/5V tol.
FP36.5 grounded lid
Space Level B
AT60142HT-DS17MSR(2)
-55° to +125°C
17 ns/5V tol.
FP36.5 grounded lid
Space Level B RHA
-55° to +125°C
17 ns/5V tol.
FP36.5 grounded lid
ESCC
AT60142HT-DS17MMQ
AT60142HT-DS17ESCC
(3)
(1)
25⋅C
17 ns/5V tol.
Die
Engineering Samples
AT60142HT-DD17MSV(1)
-55⋅ to +125⋅C
17 ns/5V tol.
Die
Space Level B
AT60142HT-DS15M-E(1)
25°C
15 ns/5V tol.
FP36.5 grounded lid
Engineering Samples
AT60142HT-DD17M-E
(1) (2)
-55° to +125°C
15 ns/5V tol.
FP36.5 grounded lid
Mil Level B
AT60142HT-DS15MSV(1) (2)
-55° to +125°C
15 ns/5V tol.
FP36.5 grounded lid
Space Level B
AT60142HT-DS15MSR(1) (2)
-55° to +125°C
15 ns/5V tol.
FP36.5 grounded lid
Space Level B RHA
-55° to +125°C
15 ns/5V tol.
FP36.5 grounded lid
ESCC
25⋅C
15 ns/5V tol.
Die
Engineering Samples
-55⋅ to +125⋅C
15 ns/5V tol.
Die
Space Level B
AT60142HT-DS15MMQ
AT60142HT-DS15ESCC
AT60142HT-DD15M-E
(3)
(1)
AT60142HT-DD15MSV(1)
Note:
1. Contact Atmel for availability.
2. Will be replaced by SMD part number when available.
3. Will be replaced by ESCC part number when available.
10
7841A–AERO–10/09
Package Drawing
36-lead Flat Pack (500 Mils)
Document Revision History
Creation from AT60142FT with the following changes :
11
•
Package DC removed
•
Update of parameters ICCSB, ICCSB1, ICCDR
AT60142HT
7841A–AERO–10/09
Headquarters
International
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Atmel Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Atmel Europe
Le Krebs
8, Rue Jean-Pierre Timbaud
BP 309
78054 Saint-Quentin-enYvelines Cedex
France
Tel: (33) 1-30-60-70-00
Fax: (33) 1-30-60-71-11
Atmel Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Technical Support
Enter Product Line E-mail
Sales Contact
www.atmel.com/contacts
Product Contact
Web Site
www.atmel.com
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF
THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
©2009 Atmel Corporation. All rights reserved. Atmel ® and combinations thereof are the registered trademarks of Atmel Corporation or its
subsidiaries. Other terms and product names may be the trademarks of others.
Printed on recycled paper.
7841A–AERO–10/09
/xM
Similar pages