Mitsubishi M37212 Single-chip 8-bit cmos microcomputer for voltage synthesizer Datasheet

MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
1. DESCRIPTION
The M37212M6-XXXSP/FP, M37212M4/M8-XXXSP are single-chip
microcomputers designed with CMOS silicon gate technology. They
have a OSD, I2C-BUS interface, and PWM, so it is useful for a channel selection system for TV.
The feature of the M37212EFSP/FP are similar to those of the
M37212M6-XXXSP/FP except that these chips have a built-in PROM
which can be written electrically. The differences between the
M37212M6-XXXSP/FP and M37212M4/M8-XXXSP are the ROM size
and the RAM size as shown below. Accordingly, the following descriptions will be for M37212M6-XXXSP/FP unless otherwise noted.
2. FEATURES
●Number
of basic instructions ..................................................... 71
●Memory size
ROM............... ......... 16K bytes (M37212M4-XXXSP)
24K bytes (M37212M6-XXXSP/FP)
32K bytes (M37212M8-XXXSP)
62K bytes (M37212EFSP/FP)
RAM ......................... 320 bytes (M37212M4-XXXSP)
384 bytes (M37212M6-XXXSP/FP)
576 bytes (M37212M8-XXXSP)
1280 bytes (M37212EFSP/FP)
(*ROM correction memory included)
●The minimum instruction execution time
......................................... 0.5 µs (at 8 MHz oscillation frequency)
●Power source voltage .................................................. 5 V ± 10 %
●Subroutine nesting
maximum 96 levels (M37212M4/M8-XXXSP, M37212M6-XXXSP/FP)
maximum 128 levels (M37212EFSP/FP)
●Interrupts ........................................................ 14 types, 14 vectors
●8-bit timers ................................................................................... 4
●Programmable I/O ports
(Ports P0, P10–P14, P2, P30, P31, P40, P41) ............................. 25
●Input ports (Ports P15–P17, P32–P37, P42) ............................... 10
●Output ports (Ports P52–P55, P60–P63) ....................................... 8
●12 V withstand ports .................................................................. 12
●LED drive ports ............................................................................ 4
●Serial I/O ............................................................. 8-bit ✕ 1 channel
●Multi-master I2C-BUS interface ............................... 1 (2 systems)
●A-D comparator (6-bit resolution) ................................. 8 channels
●PWM output circuit .......................................... 14-bit ✕ 1, 8-bit ✕ 8
●Power dissipation .............................................................. 165 mW
(at 8 MHz oscillation frequency, VCC=5.5V, at OSD display)
●ROM correction function ................................................. 2 vectors
Note: Only M37212M8-XXXSP and M37212EFSP/FP have ROM
correction function.
Rev. 1.0
●OSD function
Display characters ................................... 24 characters ✕ 2 lines
(It is possible to display 3lines or more by software)
Kinds of characters ........................................................ 256 kinds
Character display area .............................................. 12 ✕ 16 dots
Kinds of character sizes ..................................................... 3 kinds
Kinds of character colors .................................. 8 colors (R, G, B)
Coloring unit ................... character, character background, raster
Display position .............................................................................
Horizontal: 64 levels
Vertical: 128 levels
Attribute .............................................................................. border
3. APPLICATION
TV
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
TABLE OF CONTENTS
1. DESCRIPTION .......................................................................... 1
2. FEAUTURES ............................................................................. 1
3. APPLICATION ............................................................................ 1
4. PIN CONFIGURATION .............................................................. 3
5. FUNCTIONAL BLOCK DIAGRAM ............................................. 5
6. PERFORMANCE OVERVIEW ................................................... 6
7. PIN DESCRIPTION ................................................................... 8
8. FUNCTIONAL DESCRIPTION ................................................. 12
8.1 CENTRAL PROCESSING UNIT (CPU) .................... 12
8.2 MEMORY .................................................................. 13
8.3 INTERRUPTS ........................................................... 19
8.4 TIMERS ..................................................................... 24
8.5 SERIAL I/O ................................................................ 27
8.6 MULTI-MASTER I2C-BUS INTERFACE .................... 31
8.7 PWM OUTPUT CIRCUIT .......................................... 44
8.8 A-D COMPARATOR .................................................. 49
8.9 ROM CORRECTION FUNCTION ............................. 51
8.10 OSD FUNCTIONS ................................................... 52
8.10.1 Display Position ....................................... 56
8.10.2 Character Size ......................................... 60
8.10.3 Clock for OSD .......................................... 62
8.10.4 Memory for OSD ...................................... 63
8.10.5 Color Register .......................................... 66
8.10.6 Border ...................................................... 68
8.10.7 Multiline Display ....................................... 69
8.10.8 OSD Output Pin Control .......................... 70
8.10.9 Raster Coloring Function ......................... 71
8.11. SOFTWARE RUNAWAY DETECT FUNCTION ...... 72
8.12. RESET CIRCUIT .................................................... 73
8.13. CLOCK GENERATING CIRCUIT ........................... 74
8.14. DISPLAY OSCILLATION CIRCUIT ........................ 75
8.15. AUTO-CLEAR CIRCUIT ......................................... 75
8.16. ADDRESSING MODE ............................................ 75
8.17. MACHINE INSTRUCTIONS ................................... 75
9. PROGRAMMING NOTES ........................................................ 75
10. ABSOLUTE MAXIMUM RATINGS ......................................... 76
11. RECOMMENDED OPERATING CONDITIONS ..................... 76
12. ELECTRIC CHARACTERISTICS .......................................... 77
13. A-D COMPARISON CHARACTERISTICS ............................. 79
14. MULTI-MASTER I2C-BUS BUS LINE CHARACTERISTICS ........... 79
15. PROM PROGRAMMING METHOD ....................................... 80
16. DATA REQUIRED FOR MASK ORDERS .............................. 81
17. MASK CONFIRMATION FORM ............................................. 82
18. MARK SPECIFICATION FORM ............................................. 91
19. ONE TIME PROM VERSIONS M37212EFSP/FP MARKING .... 93
20. APPENDIX ............................................................................. 94
21. PACKAGE OUTLINE ........................................................... 117
Rev. 1.0
2
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
4. PIN CONFIGURATION
1
52
P52/R
VSYNC
P60/PWM0
P61/PWM1
2
51
3
50
4
49
P53/G
P54/B
P55/OUT1
P62/PWM2
5
48
P63/PWM3
P00/PWM4
P01/PWM5
P02/PWM6
6
P03/PWM7
P42/SIN/A-D5
P41/SCLK/A-D6
P40/SOUT(/IN)/A-D7
10
DA
P35/INT2/A-D4
P34/INT1
P33/TIM3
14
P32/TIM2
18
P24
P25
19
P26
P27
CNVSS
XIN
21
7
8
9
11
12
13
15
16
17
20
M37212M4/M6/M8-XXXSP, M37212EFSP
HSYNC
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
P20
P21
P22
P23
P04
P05
P06
P07
P10/OUT2/A-D8
P11/SCL1
P12/SCL2
P13/SDA1
P14/SDA2
P15/INT3/A-D1
P16/A-D2
P17/A-D3
P30
24
29
P31
RESET
OSC1/P36
XOUT
25
28
OSC2/P37
VSS
26
27
VC C
22
31
23
30
Outline 52P4B
Fig. 4.1 Pin Configuration 1 (Top View)
Rev. 1.0
3
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
P21
41
42
NC
NC
NC
NC
43
44
45
P15/INT3/A-D1
P16/A-D2
P17/A-D3
46
47
48
49
50
51
52
53
54
56
55
P04
P05
P06
P07
P10/OUT2/A-D8
NC
P11/SCL1
P12/SCL2
P13/SDA1
P14/SDA2
NC
58
57
P22
P23
59
NC
60
61
62
63
64
NC
NC
NC
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
65
40
NC
P20
66
39
67
38
P30
NC
P31
P55/OUT1
P54/B
P53/G
P52/R
68
37
RESET
69
36
70
35
NC
NC
72
31
75
30
XOUT
76
29
77
28
78
27
79
26
80
25
XIN
CNVSS
P27
NC
NC
Outline 80P6N-A
24
23
22
20
21
19
18
17
33
P32/TIM2
P24
P25
P26
NC
NC
NC
NC
16
15
14
13
11
12
P40/SOUT(/IN)/A-D7
DA
P35/INT2/A-D4
P34/INT1
P33/TIM3
9
10
8
7
6
5
4
NC
NC
NC
NC
P00/PWM4
P01/PWM5
P02/PWM6
P03/PWM7
NC
P42/SIN/A-D5
P41/SCLK/A-D6
1
P63/PWM3
32
74
M37212M6-XXXFP, M37212EFFP
3
P60/PWM0
P61/PWM1
P62/PWM2
NC
73
VCC
NC
NC
VSS
34
71
2
HSYNC
VSYNC
OSC1/P36
OSC2/P37
NC : Unconnected
Fig. 4.2 Pin Configuration 2 (Top View)
Rev. 1.0
4
I/O port P0
2221201945 464748
I/O ports P1 0–P14
Input ports P1 5–P1 7
I/O port P2
33 34353637383940
4142 434410 9 8 7
P2 (8)
Index
register
X (8)
23
TIM3
TIM2
Multi-master
I2C-BUS interface
Timer 4
T4 (8)
Timer 3
T3 (8)
Timer 2
T2 (8)
Timer 1
T1 (8)
1112 13
P4 (3)
Timer count source
selection circuit
SI/O(8)
DA
8-bit PWM circuit
Instruction
register (8)
Instruction
decoder
Control signal
Input port P4 2
I/O ports P3 0, P31
I/O ports P40, P4 1
Input ports P3 2–P35
14
P3 (6)
Stack
pointer
S (8)
ROM
26
VSS CNVSS
1516 1718 3132
14-bit
PWM circuit
Index
register
Y (8)
PC L (8)
PCH (8)
A-D
comparator
P1 (8)
Accumulator
A (8)
Processor
status
register
PS (8)
P0 (8)
8-bit
arithmetic
and
logical unit
Address bus
Program
counter
Program
counter
INT3
RAM
INT1
Data bus
INT2
Clock
generating
circuit
27
SCL
VCC
SDA
30
SIN
SCLK
SOUT(/IN)
25
28
6 5 4 3
P6 (4)
CRT circuit
29
P5 (4)
49 505152
2 1
Output ports P6 0–P6 3 Output ports P5 2–P5 5
Output for display
PWM7
PWM6
PWM5
PWM4
PWM3
PWM2
PWM1
PWM0
24
OUT2
Input ports P3 6, P37
Clock input for display Clock output for display
OSC1 OSC2
OUT1
B
G
R
Reset input
RESET
VSYNC
HSYNC
Clock input Clock output
XIN X OUT ( ) Timing output
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
5. FUNCTIONAL BLOCK DIAGRAM
Fig. 5.1 Functional Block Diagram of M37212
Rev. 1.0
5
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
6. PERFORMANCE OVERVIEW
Table 6.1 Performance Overview
Parameter
Functions
Number of basic instructions
71
Number of basic instructions
0.5 µs (the minimum instruction execution time, at 8 MHz oscillation fre
quency)
Instruction execution time
Memory size
8 MHz (maximum)
ROM M37212M4-XXXSP
16K bytes
M37212M6-XXXSP/FP 24K bytes
M37212M8-XXXSP
32K bytes
M37212EFSP/FP
62K bytes
RAM M37212M4-XXXSP
320 bytes
M37212M6-XXXSP/FP 384 bytes
Input/Output ports
M37212M8-XXXSP
576 bytes (ROM correction memory included)
M37212EFSP/FP
1280 bytes (ROM correction memory included)
OSD ROM
8 K bytes
OSD RAM
96 bytes
P0
I/O
8-bit ✕ 1 (N-channel open-drain output structure, can be used as PWM
output pins)
P10–P14
I/O
5-bit ✕ 1 (CMOS input/output output structure, however, N-channel opendrain output structure, when P11–P14 are used as multi-master I2C-BUS
interface, can be used as OSD output, A-D input, multi-master I2C-BUS
interface)
P15–P17
Input
P20–P27
I/O
8-bit ✕ 1 (CMOS input/output structure)
P30, P31
I/O
2-bit ✕ 1 (CMOS input/output structure)
P32–P37
Input
6-bit ✕ 1 (can be used as external clock input pins, INT input pins, OSD
display clock I/O pins, A-D input pins)
P40, P41
I/O
2-bit ✕ 1 (N-channel open-drain output structure, can be used as serial I/O
pins, A-D input pins)
P42
Input
3-bit ✕ 1 (can be used as INT input pin, A-D input pins)
1-bit ✕ 1(can be used as serial input pin, A-D input pin)
P52–P55
Output
4-bit ✕ 1 (CMOS output structure, can be used as OSD output pins)
P60–P63
Output
4-bit ✕ 1 (N-channel open-drain output structure, can be used as PWM
output pins)
Serial I/O
8-bit ✕ 1
Multi-master I2C-BUS interface
1 (2 systems)
A-D comparator
8 channels (6-bit resolution)
PWM output circuit
14-bit ✕ 1, 8-bit ✕ 8
Timers
8-bit timer ✕ 4
Subroutine nesting
96 levels (maximum)
Interrupt
<14 sources>
INT external interrupt ✕ 3, Internal timer interrupt ✕ 4, Serial I/O interrupt ✕ 1,
OSD interrupt ✕ 1, Multi-master I2C-BUS interface interrupt ✕ 1, f(XIN)/4096
interrupt ✕ 1, VSYNC interrupt ✕ 1, BRK interrupt ✕ 1, Reset ✕ 1
Clock generating circuit
2 built-in circuits (externally connected a ceramic resonator or a quartzcrystal oscillator)
Rev. 1.0
6
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Table 6.2 Performance Overview (continued)
Parameter
OSD display
function
Number of display characters
Functions
24 characters ✕ 2 lines
Dot structure
12 ✕ 16 dots
Kinds of characters
254 kinds
Kinds of character sizes
3 kinds
Character font coloring
1 screen: 8 kinds (per character unit)
Display position
Horizontal: 64 levels, Vertical: 128 levels
5 V ± 10 %
Power source voltage
Power dissipation
OSD ON
165 mW typ. (at oscillation frequency f(XIN) = 8 MHz, fOSC = 8 MHz)
OSD OFF
110 mW typ. (at oscillation frequency f(XIN) = 8 MHz)
In stop mode
1.65 mW (maximum)
Operating temperature range
–10 °C to 70 °C
Device structure
CMOS silicon gate process
Package
M37212M4/M6/M8-XXXSP, M37212EFSP
52-pin plastic molded SDIP
M37212M6-XXXFP, M37212EFSP
80-pin plastic molded QFP
Rev. 1.0
7
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
7. PIN DESCRIPTION
Table 7.1 Pin Description
Pin
Name
VCC,
VSS.
Power source
CNVSS
CNVSS
Input/
Output
Functions
Apply voltage of 5 V ± 10 % to (typical) VCC, and 0 V to VSS.
This is connected to VSS.
______
RESET
Reset input
Input
To enter the reset state, the reset input pin must be kept at a “L” for 2 µs or more (under
normal VCC conditions).
If more time is needed for the quartz-crystal oscillator to stabilize, this “L” condition should
be maintained for the required time.
XIN
Clock input
Input
XOUT
Clock output
This chip has an internal clock generating circuit. To control generating frequency, an
external ceramic resonator or a quartz-crystal oscillator is connected between pins XIN and
XOUT. If an external clock is used, the clock source should be connected to the XIN pin and
the XOUT pin should be left open.
P00/PWM4– I/O port P0
P03/PWM7,
P04–P07
PWM output
P10/OUT2/ I/O port P1
A-D8,
P11/SCL1, OSD output
P12/SCL2, Multi-master
P13/SDA1, I2C-BUS interface
Output
I/O
Port P0 is an 8-bit I/O port with direction register allowing each I/O bit to be individually
programmed as input or output. At reset, this port is set to input mode. The output structure
is N-channel open-drain output. (See note)
Output
Pins P00–P03 are also used as PWM output pins PWM4–PWM7 respectively. The output
structure is N-channel open-drain output.
I/O
Port P10–P14 are a 5-bit I/O port and has basically the same functions as port P0. The
output structure is CMOS output.
Output
I/O
Pins P10 is also used as OSD output pin OUT2. The output structure is CMOS output.
Pins P11–P14 are used as SCL1, SCL2, SDA1 and SDA2 respectively, when multi-master
I2C-BUS interface is used. The output structure is N-channel open-drain output.
P14/SDA2, Analog input
Input
P10 pin is also used as analog input pin A-D8.
P15/INT3/
A-D1,
Input port P1
Input
Port P15–P17 are a 3-bit input port and has basically the same functions as port P0.
Analog input
Input
Pins P15–P17 are also used as analog input pins A-D1 to A-D3 respectively.
P16/A-D2,
P17/A-D3
External interrupt
input
Input
P15 pin is also used as INT external interrupt input pin INT3.
P20–P27
I/O port P2
I/O
Port P2 is an 8-bit I/O port and has basically the same functions as port P0. The output
structure is CMOS output. (See note)
P30, P31
I/O port P3
I/O
Ports P30, P31 are a 2-bit I/O port and has basically the same functions as port P0. The
output structure is CMOS output.
P32/TIM2,
Input port P3
Input
Ports P32–P37 are a 6-bit input port and has basically the same functions as port P0.
P33/TIM3,
External clock input
Input
Pins P32, P33 are also used as external clock input pins TIM2, TIM3 respectively.
P34/INT1,
Input
Pins P34, P35 are also used as INT external interrupt input pins INT1, INT2 respectively.
P35/INT2/
External interrupt
input
A-D4,
Analog input
P36/OSC1, Clock input for
P37/OSC2 OSD display
Clock output for
OSD display
Input
P35 pin is also used as analog input pin A-D4.
Input
P36 pin is also used as OSD display clock input pin OSC1.
Output
P37 pin is also used as OSD display clock output pin OSC2. The output structure is CMOS
output.
Rev. 1.0
8
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Table 7.2 Pin Description (continued)
Pin
Name
Input/
Output
Functions
P40/SOUT(/IN)/ I/O port P4
A-D7,
I/O
Ports P40, P41 are a 2-bit I/O port and has basically the same functions as port P0. The
output structure is N-channel open-drain output.
P41/SCLK/
A-D6,
Serial I/O data
input/output
I/O
Pin P40 is also used as serial I/O data input/output pin SOUT(/IN). The output structure is Nchannel open-drain output.
Serial I/O synchronizing
clock input/output
I/O
Pin P41 is also used as serial I/O synchronizing clock input/output pin S CLK. The output
structure is N-channel open-drain output.
Analog input pin
Input
P42/SIN/
Input port P4
Input
Port P42 is a 1-bit input port and has basically the same functions as port P0.
A-D5,
Serial I/O data
input
Input
Pin P42 is also used as serial I/O data input pin SIN.
P52/R,
P53/G,
P54/B,
P55/OUT1
Output port P5
Output
Ports P52–P55 are a 4-bit output port and has basically the same functions as port P0. The
output structure is CMOS output.
OSD output
Output
Pins P52–P55 are also used as OSD output pins R, G, B, OUT1 respectively. The output
structure is CMOS output.
Output
Ports P60–P63 are a 4-bit I/O port and has basically the same functions as port P0. The
output structure is N-channel open-drain output.
PWM output
Output
Pins P60–P63 are also used as PWM output pins PWM0–PWM3 respectively. The output
structure is N-channel open-drain output.
HSYNC
HSYNC input
Input
This is a horizontal synchronizing signal input for OSD.
VSYNC
VSYNC input
Input
This is a vertical synchronizing signal input for OSD.
DA
DA output
Analog input
P60PWM0– Output port P6
P63/PWM3
Input
Output
Pin P40, P41 are also used as analog input pins A-D7, A-D6 respectively.
Pin P42 is also used as analog input pin A-D5.
This is a 14-bit PWM output pin.
Note : Port Pi (i = 0 to 3) has the port Pi direction register which can be used to program each bit as an input (“0”) or an output (“1”). The pins programmed as “1” in
the direction register are output pins. When pins are programmed as “0,” they are input pins. When pins are programmed as output pins, the output data are
written into the port latch and then output. When data is read from the output pins, the output pin level is not read but the data of the port latch is read. This
allows a previously-output value to be read correctly even if the output “L” voltage has risen, for example, because a light emitting diode was directly driven.
The input pins are in the floating state, so the values of the pins can be read. When data is written into the input pin, it is written only into the port latch, while
the pin remains in the floating state.
Rev. 1.0
9
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Port P0
N-channel open-drain output
Direction register
Port P0
Note : Each port is also used as follows :
P00–P03 : PWM4–PWM7
Port latch
Data bus
Ports P10, P2, P30, P31
Direction register
CMOS output
Data bus
Ports P10, P2, P30, P31
Port latch
Note : Port P10 is also used as OUT2/
A-D8.
Ports P40, P41
SIN, SCLK
N-channel open-drain output
Direction register
Ports P40, P41
Note : Each port is also used as follows :
P40 : SOUT(/IN)/A-D7
P41 : SCLK/A-D6
Port latch
Data bus
BSEL0
BSEL1
Ports P11–P14
Direction register
Data bus
I2C-BUS clock
I2C-BUS data
Port latch
SCL1, SCL2,
SDA1, SDA2
N-channel open-drain output
CMOS output
Ports P11–P14
Notes 1: Each port is also used as follows :
P11 : SCL1
P12 : SCL2
P13 : SDA1
P14 : SDA2
2: The output structure of ports P11–
P14 is N-channel open-drain output
when using as multi-master I2CBUS interface (it is the same with
ports P40 and P41).
Fig. 7.1 I/O Pin Block Diagram (1)
Rev. 1.0
10
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
PortsP16, P17
Data bus
Ports P16, P17
Note : Each port is also used as follows :
P16 : A-D2
P17 : A-D3
PortsP15, P32–P37, P4 2
Schmidt input
TIM2, TIM3,
INT1,
INT2, S IN, INT3
Data bus
Ports P6 0–P63
Ports P15, P32–P37, P42
Note : Each port is also used as follows :
P15 : INT3/A-D1
P32 : TIM2
P33 : TIM3
P34 : INT1
P35 : INT2/A-D4
P36 : OSC1
P37 : OSC2
P42 : SIN/A-D5
N-chanel open drain output
Ports P60–P63
Data bus
Port latch
Note : Each port is also used as follows :
P60–P63 : PWM0–PWM3
D-A, R, G, B, OUT1 , OUT2
CMOS output
Internal circuit
Ports D-A, R, G, B, OUT1, OUT2
Note : Each pin is also used as follows :
R : P52
G : P53
B : P54
OUT1 : P55
OUT2 : P10/A-D8
HSYNC, VSYNC
Schmidt input
Internal circuit
Ports HSYNC, VSYNC
Fig. 7.2 I/O Pin Block Diagram (2)
Rev. 1.0
11
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8. FUNCTIONAL DESCRIPTION
8.1 CENTRAL PROCESSING UNIT (CPU)
8.1.1 CPU Mode Register
This microcomputer uses the standard 740 Family instruction set.
Refer to the table of 740 Family addressing modes and machine
instructions or the SERIES 740 <Software> User’s Manual for details on the instruction set.
Machine-resident 740 Family instructions are as follows:
The FST, SLW instruction cannot be used.
The MUL, DIV, WIT and STP instructions can be used.
The CPU mode register contains the stack page selection bit and
internal system clock selection bit. The CPU mode register is allocated at address 00FB16.
CPU Mode Register
b7 b6 b5 b4 b3 b2 b1 b0
1 1 1 1 1
0 0
CPU mode register (CM) [Address 00FB16]
B
Name
Functions
0, 1 Fix these bits to “0.”
2
Stack page selection
bit (CM2) (See note)
0: 0 page
1: 1 page
3 to 7 Fix these bits to “1.”
After reset R W
Indeterminate
R W
1
RW
Indeterminate
R W
Note: This bit is set to “1” after the reset release.
Fig. 8.1.1 CPU Mode Register
Rev. 1.0
12
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.2 MEMORY
8.2.1 Special Function Register (SFR) Area
8.2.7 Zero Page
The special function register (SFR) area in the zero page contains
control registers such as I/O ports and timers.
RAM is used for data storage and for stack area of subroutine calls
and interrupts.
The 256 bytes from addresses 000016 to 00FF16 are called the zero
page area. The internal RAM and the special function registers (SFR)
are allocated to this area.
The zero page addressing mode can be used to specify memory and
register addresses in the zero page area. Access to this area with
only 2 bytes is possible in the zero page addressing mode.
8.2.3 ROM
8.2.8 Special Page
ROM is used for storing user programs as well as the interrupt vector
area.
The 256 bytes from addresses FF0016 to FFFF16 are called the special page area. The special page addressing mode can be used to
specify memory addresses in the special page area. Access to this
area with only 2 bytes is possible in the special page addressing
mode.
8.2.2 RAM
8.2.4 OSD RAM
RAM for display is used for specifying the character codes and colors to display.
8.2.9 ROM Correction Memory (RAM)
8.2.5 OSD ROM
This is used as the program area for ROM correction.
ROM for display is used for storing character data.
Note: Only M37212M8-XXXSP and M37212EFSP/FP have ROM correction
memory.
8.2.6 Interrupt Vector Area
The interrupt vector area contains reset and interrupt vectors.
■ M37212M4/M8-XXXSP, M37212M6-XXXSP/FP
000016
M37212M6XXXSP/FP
RAM
(384 bytes)
M37212M4XXXSP
RAM
(320 bytes)
00BF16
00C016
00FF16
010016
1000016
Zero page
SFR area
OSD ROM
(8K bytes)
11FFF16
017F16
01BF16
Not used
Not used
OSD RAM
(96 bytes)
(See note)
M37212M6XXXSP/FP
ROM
(24K bytes)
060016
06B716
Not used
A00016
C00016
M37212M4XXXSP
ROM
(16K bytes)
FF0016
FFDE16
FFFF16
Interrupt vector area
Special page
1FFFF16
Note: Refer to Table 8.10.3 OSD RAM.
Fig. 8.2.1 Memory Map (M37212M4/M8-XXXSP, M37212M6-XXXSP/FP)
Rev. 1.0
13
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
■ M37212M8-XXXSP, M37212EFSP/FP
000016
M37212EFSP
RAM
(1280 bytes)
M37212M8XXXSP
RAM
(576 bytes)
00BF16
00C016
00FF16
010016
01FF16
021716
1000016
Zero page
OSD ROM
(8K bytes)
SFR area
11FFF16
Not used
2 page register
021B16
Not used
02C016
ROM correction function
Vector 1: address 02C016
Vector 2: address 02E016
02E016
033F16
OSD RAM
(96 bytes)
(See note)
05FF16
060016
Not used
06B716
M37212EFSP
ROM
(62K bytes)
Not used
080016
800016
M37212M8XXXSP
ROM
(32K bytes)
FF0016
FFDE16
FFFF16
Interrupt vector area
Special page
1FFFF16
Note: Refer to Table 8.10.3 OSD RAM
Fig. 8.2.2 Memory Map (M37212M8-XXXSP, M37212EFSP/FP)
Rev. 1.0
14
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
■ SFR area (addresses C016 to DF16)
State immediately after reset
Bit allocation
:
Name
0 : “0” immediately after reset
Function bit
:
1 : “1” immediately after reset
: No function bit
? : Indeterminate immediately
after reset
0 : Fix to this bit to “0”
(do not write to “1”)
1 : Fix to this bit to “1”
(do not write to “0”)
Address
C016
C116
C216
C316
C416
C516
C616
C716
C816
C916
CA16
CB16
CC16
CD16
CE16
CF16
D016
D116
D216
D316
D416
D516
D616
D716
D816
D916
DA16
DB16
DC16
DD16
DE16
DF16
Register
Bit allocation
State immediately after reset
b0 b7
b7
b0
Port P0 (P0)
Port P0 direction register (D0)
Port P1 (P1)
Port P1 direction register (D1)
Port P2 (P2)
Port P2 direction register (D2)
Port P3 (P3)
Port P3 direction register (D3)
P31D P30D
P41 P40
Port P4 (P4)
P41D P40D
Port P4 direction register (D4)
Port P5 (P5)
Port P5 direction register (D5)
P55
P54
P55
SEL
P54 P53 P52
SEL SEL SEL
P63 P62
Port P6 (P6)
P53 P52
1
1
0
0
0
0
0
0
0
0
0
?
0
0
?
0
0
0
0
P61 P60
1
1
DA-H register (DA-H)
DA-L register (DA-L)
PWM0 register (PWM0)
PWM1 register (PWM1)
PWM2 register (PWM2)
PWM3 register (PWM3)
PWM4 register (PWM4)
PWM output control register 1 (PW)
PW7 PW6 PW5 PW4 PW3 PW2 PW1 PW0
P N4 P N3 P N2 P N1 P N0
PWM output control register 2 (PN)
I2C
data shift register (S0)
I2 C
address register (S0D)
I2C status register (S1)
I2C control register (S1D)
I2C clock control register (S2)
Serial I/O mode register (SM)
D7
D6
D5
D4
D3
D2
D1
D0
SAD6 SAD5 SAD4 SAD3 SAD2 SAD1 SAD0 RBW
MST TRX BB
PIN
AL AAS AD0 LRB
BSEL1 BSEL0 10BIT ALS ESO BC2 BC1 BC0
SAD
ST
ACK ABCITK MFA
ODE CCR4 CCR3 CCR2 CCR1 CCR0
SM6 SM5
Serial I/O register (SIO)
0
SM3 SM2 SM1 SM0
?
0016
?
0016
?
0016
?
0016
0 0
0 0
? ?
0016
0F16
0F16
?
? ?
?
?
?
?
?
0016
0016
?
0016
1 0
0016
0016
0016
?
?
?
?
?
?
?
?
0
?
?
0
?
?
?
0
0
?
Fig. 8.2.3 Memory Map of Special Function Register (SFR) (1)
Rev. 1.0
15
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
■ SFR area (addresses E016 to FF16)
State immediately after reset
Bit allocation
:
Name
0 : “0” immediately after reset
Function bit
:
1 : “1” immediately after reset
: No function bit
? : Indeterminate immediately
after reset
0 : Fix to this bit to “0”
(do not write to “1”)
1 : Fix to this bit to “1”
(do not write to “0”)
Address
Bit allocation
Register
State immediately after reset
b0 b7
b7
E016
E116
E216
E316
E416
E516
E616
E716
E816
E916
EA16
EB16
EC16
ED16
EE16
EF16
F016
F116
F216
F316
F416
F516
F616
F716
F816
F916
FA16
FB16
FC16
FD16
FE16
FF16
Horizontal position register (HR)
b0
HR5 HR4 HR3 HR2 HR1 HR0
Vertical position register 1 (CV1)
CV16 CV15 CV14 CV13 CV12 CV11 CV10
Vertical position register 2 (CV2)
CV26 CV25 CV24 CV23 CV22 CV21 CV20
CS21 CS20 CS11 CS10
Character size register (CS)
Border selection register (MD)
Color register 0 (CO0)
CO07 CO06 CO05 CO04 CO03 CO02 CO01
Color register 1 (CO1)
CO17 CO16 CO15 CO14 CO13 CO12 CO11
MD20
MD10
Color register 2 (CO2)
CO27 CO26 CO25 CO24 CO23 CO22 CO21
Color register 3 (CO3)
CO37 CO36 CO35 CO34 CO33 CO32 CO31
CRT control register (CC)
CC7
CRT port control register (CRTP)
OP7 OP6 OP5 OUT1 OUT2 R/G/B VSYC HSYC
CRT clock selection register (CK) 0
A-D mode register (ADM)
0
0
?
?
?
?
0
0
0
0
0
0
0
0
0
?
0
0
CC2 CC1 CC0
0
0
0
0
0
CK1 CK0
ADM2 ADM1 ADM0
ADM4
ADC5 ADC4 ADC3 ADC2 ADC1 ADC0
A-D control register (ADC)
Timer 1 (T1)
Timer 2 (T2)
Timer 3 (T3)
Timer 4 (T4)
0
Timer 12 mode register (T12M)
T12M4 T12M3 T12M2 T12M1 T12M0
T34M5 T34M4 T34M3 T34M2 T34M1 T34M0
Timer 34 mode register (T34M)
PWM5 register (PWM5)
PWM6 register (PWM6)
PWM7 register (PWM7)
Interrupt input polarity register (RE) 0
RE5 RE4 RE3
1
CPU mode register (CM)
Interrupt request register 1 (IREQ1) IT3R
IICR VSCR OSDR TM4R TM3R TM2R TM1R
Interrupt request register 2 (IREQ2) 0
Interrupt control register 1 (ICON1) IT3E
IICE VSCE OSDE TM4E TM3E TM2E TM1E
Interrupt control register 2 (ICON2)
1
1
1
1
0
0
MSE
0
0
S1R IT2R IT1R
MCSKR0
0
CM2
0
S1E IT2E IT1E
0016
? ?
? ?
0016
0 ?
0 0
0016
0016
0016
0016
0016
0016
0016
0016
? 0
0016
FF16
0716
FF16
0716
0016
0016
?
?
?
0016
?
FC16
0016
0016
0016
0 0
?
?
?
?
?
?
?
?
?
0
?
?
0
0
0
0
0
0
Fig. 8.2.4 Memory Map of Special Function Register (SFR) (2)
Rev. 1.0
16
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
■ 2 page register area (addresses 21716 to 21B16)
<Bit allocation>
:
<State immediately after reset>
0 : “0” immediately after reset
Function bit
Name
:
1 : “1” immediately after reset
: No function bit
? : Indeterminate immediately
after reset
0 : Fix to this bit to “0”
(do not write to “1”)
1 : Fix to this bit to “1”
(do not write to “0”)
Address
21716
21816
21916
21A16
21B16
Register
Bit allocation
State immediately after reset
b7
b0 b7
ROM correction address 1 (high-order)
ROM correction address 1 (low-order)
ROM correction address 2 (high-order)
ROM correction address 2 (low-order)
ROM correction enable register (RCR)
0
0
RCR1RCR0
b0
0016
0016
0016
0016
0016
Note: Only M37212M8-XXXSP and M37212EFSP/FP have 2 page register.
Fig. 8.2.5 Memory Map of 2 Page Register Area
Rev. 1.0
17
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
<Bit allocation>
:
Name
<State immediately after reset>
0 : “0” immediately after reset
Function bit
:
1 : “1” immediately after reset
: No function bit
? : Indeterminate immediately
after reset
0 : Fix to this bit to “0”
(do not write to “1”)
1 : Fix to this bit to “1”
(do not write to “0”)
Register
Bit allocation
State immediately after reset
b0 b7
b7
Processor status register (PS)
Program counter (PCH)
N
V
T
B
D
I
Z
C
Program counter (PCL)
b0
? ? ? ? ? 1 ? ?
Contents of address FFFF16
Contents of address FFFE16
Fig. 8.2.6 Internal State of Processor Status Register and Program Counter at Reset
Rev. 1.0
18
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.3 INTERRUPTS
Interrupts can be caused by 14 different sources consisting of 4 external, 8 internal, 1 software, and reset. Interrupts are vectored interrupts with priorities as shown in Table 8.3.1. Reset is also included in
the table because its operation is similar to an interrupt.
When an interrupt is accepted,
① The contents of the program counter and processor status register are automatically stored into the stack.
➁ The interrupt disable flag I is set to “1” and the corresponding
interrupt request bit is set to “0.”
➂ The jump destination address stored in the vector address enters
the program counter.
Other interrupts are disabled when the interrupt disable flag is set to
“1.”
All interrupts except the BRK instruction interrupt have an interrupt
request bit and an interrupt enable bit. The interrupt request bits are
in interrupt request registers 1 and 2 and the interrupt enable bits are
in interrupt control registers 1 and 2. Figures 8.3.2 to 8.3.6 show the
interrupt-related registers.
Interrupts other than the BRK instruction interrupt and reset are accepted when the interrupt enable bit is “1,” interrupt request bit is “1,”
and the interrupt disable flag is “0.” The interrupt request bit can be
set to “0” by a program, but not set to “1.” The interrupt enable bit can
be set to “0” and “1” by a program.
Reset is treated as a non-maskable interrupt with the highest priority.
Figure 8.3.1 shows interrupt control.
8.3.1 Interrupt Causes
(1) VSYNC, OSD interrupts
The VSYNC interrupt is an interrupt request synchronized with
the vertical sync signal.
The OSD interrupt occurs after character block display to the
CRT is completed.
(2) INT1 to INT3 external interrupts
The INT1 to INT3 interrupts are external interrupt inputs, the system detects that the level of a pin changes from LOW to HIGH or
from HIGH to LOW, and generates an interrupt request. The input active edge can be selected by bits 3 to 5 of the interrupt
input polarity register (address 00F916) : when this bit is “0,” a
change from LOW to HIGH is detected; when it is “1,” a change
from HIGH to LOW is detected. Note that both bits are cleared to
“0” at reset.
(3) Timers 1 to 4 interrupts
An interrupt is generated by an overflow of timers 1 to 4.
Table 8.3.1 Interrupt Vector Addresses and Priority
Priority
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Interrupt Source
Reset
OSD interrupt
INT2 external interrupt
INT1 external interrupt
Timer 4 interrupt
f(XIN)/4096 interrupt
VSYNC interrupt
Timer 3 interrupt
Timer 2 interrupt
Timer 1 interrupt
Serial I/O interrupt
Multi-master I2C-BUS interface interrupt
INT3 external interrupt
BRK instruction interrupt
Vector Addresses
FFFF16, FFFE16
FFFD16, FFFC16
FFFB16, FFFA16
FFF916, FFF816
FFF516, FFF416
FFF316, FFF216
FFF116, FFF016
FFEF16, FFEE16
FFED16, FFEC16
FFEB16, FFEA16
FFE916, FFE816
FFE716, FFE616
FFE516, FFE416
FFDF16, FFDE16
Remarks
Non-maskable
Active edge selectable
Active edge selectable
Active edge selectable
Non-maskable
Rev. 1.0
19
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
(4) Serial I/O interrupt
This is an interrupt request from the clock synchronous serial I/O
function.
(5) f(XIN)/4096 interrupt
The f (XIN)/4096 interrupt occurs regularly with a f(XIN)/4096 period. Set bit 0 of PWM output control register 1 to “0.”
(6) Multi-master I2C-BUS interface interrupt
Interrupt request bit
Interrupt enable bit
Interrupt disable flag I
This is an interrupt request related to the multi-master I2C-BUS
interface.
BRK instruction
Reset
Interrupt
request
(7) BRK instruction interrupt
This software interrupt has the least significant priority. It does
not have a corresponding interrupt enable bit, and it is not affected by the interrupt disable flag I (non-maskable).
Fig. 8.3.1 Interrupt Control
Rev. 1.0
20
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Interrupt Request Register 1
b7 b6 b5 b4 b3 b2 b1 b0
Interrupt request register 1 (IREQ1) [Address 00FC16]
B
Name
0 Timer 1 interrupt
request bit (TM1R)
Functions
After reset
0
0 : No interrupt request issued
1 : Interrupt request issued
Timer 2 interrupt
0
0 : No interrupt request issued
request bit (TM2R) 1 : Interrupt request issued
0
Timer 3 interrupt
0 : No interrupt request issued
request bit (TM3R) 1 : Interrupt request issued
0
Timer 4 interrupt
0 : No interrupt request issued
request bit (TM4R) 1 : Interrupt request issued
OSD interrupt request 0 : No interrupt request issued
0
1 : Interrupt request issued
bit (OSDR)
VSYNC interrupt
0
0 : No interrupt request issued
request bit (VSCR) 1 : Interrupt request issued
0
Multi-master I2C-BUS interface 0 : No interrupt request issued
interrupt request bit (IICR)
1 : Interrupt request issued
0
0 : No interrupt request issued
INT3 external interrupt
request bit (IT3R)
1 : Interrupt request issued
R W
R ✽
1
R ✽
2
3
4
5
6
7
R ✽
R ✽
R ✽
R ✽
R ✽
R ✽
✽: “0” can be set by software, but “1” cannot be set.
Fig. 8.3.2 Interrupt Request Register 1
Interrupt Request Register 2
b7 b6 b5 b4 b3 b2 b1 b0
0
Interrupt request register 2 (IREQ2) [Address 00FD16]
B
Name
0 INT1 external interrupt
Functions
After reset R W
0 : No interrupt request issued
1 : Interrupt request issued
0 : No interrupt request issued
1 : Interrupt request issued
0
R ✽
0
R ✽
0 : No interrupt request issued
1 : Interrupt request issued
3 Nothing is assigned. This bit is a write disable bit.
When this bit is read out, the value is “0.”
4 f(XIN)/4096 interrupt 0 : No interrupt request issued
request bit (MSR)
1 : Interrupt request issued
5, 6 Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are “0.”
7 Fix this bit to “0.”
0
R ✽
0
R —
0
R ✽
0
R —
0
R W
request bit (IT1R)
1
INT2 external interrupt
request bit (IT2R)
2
Serial I/O interrupt
request bit (S1R)
✽: “0” can be set by software, but “1” cannot be set.
Fig. 8.3.3 Interrupt Request Register 2
Rev. 1.0
21
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Interrupt Control Register 1
b7 b6 b5 b4 b3 b2 b1 b0
Interrupt control register 1 (ICON1) [Address 00FE16]
B
Name
Functions
After reset R W
0 Timer 1 interrupt
enable bit (TM1E)
1 Timer 2 interrupt
enable bit (TM2E)
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
2 Timer 3 interrupt
enable bit (TM3E)
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
3 Timer 4 interrupt
enable bit (TM4E)
4 OSD interrupt enable bit
(OSDE)
5 VSYNC interrupt enable
bit (VSCE)
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
6 Multi-master I2C-BUS interface 0 : Interrupt disabled
interrupt enable bit (IICE)
1 : Interrupt enabled
0
R W
7 INT3 external interrupt
enable bit (IT3E)
0
R W
0 : Interrupt disabled
1 : Interrupt enabled
Fig. 8.3.4 Interrupt Control Register 1
Interrupt Control Register 2
b7 b6 b5 b4 b3 b2 b1 b0
0 0
0
Interrupt control register 2 (ICON2) [Address 00FF16]
B
Name
0 INT1 external interrupt
enable bit (IT1E)
1 INT2 external interrupt
enable bit (IT2E)
2 Serial I/O interrupt
enable bit (S1E)
3 Fix this bit to “0.”
4 f(XIN)/4096 interrupt
enable bit (MSE)
5, 6 Fix these bits to “0.”
7
Functions
After reset
R W
0 : Interrupt disabled
1 : Interrupt enabled
0 : Interrupt disabled
1 : Interrupt enabled
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
0
R W
0
R W
0
R W
0
R W
0
R W
indeterminate
R –
0 : Interrupt disabled
1 : Interrupt enabled
Nothing is assigned. These bits are write disable bits. When
these bits are read out, the values are “indeterminate.”
Fig. 8.3.5 Interrupt Control Register 2
Rev. 1.0
22
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Interrupt Input Polarity Register
b7 b6 b5 b4 b3 b2 b1 b0
0
0
Interrupt input polarity register(RE) [Address 00F916]
B
Name
Functions
0, 1 Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are “0.”
2
Fix this bit to “0.”
After reset
R W
0
R —
0
R W
3
INT1 polarity switch bit
(RE3)
0 : Positive polarity
1 : Negative polarity
0
R W
4
INT2 polarity switch bit
(R E 4)
0 : Positive polarity
1 : Negative polarity
0
R W
5
INT3 polarity switch bit
(R E 5)
0 : Positive polarity
1 : Negative polarity
0
R W
6
Nothing is assigned. This bit is a write disable bit.
When this bit is read out, the value is “0.”
0
R —
7
Fix this bit to “0.”
0
R W
Fig. 8.3.6 Interrupt Input Polarity Register
Rev. 1.0
23
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.4 TIMERS
This microcomputer has 4 timers: timers 1 to 4. All timers are 8-bit
timers with the 8-bit timer latch. The timer block diagram is shown in
Figure 8.4.3.
All of the timers count down and their divide ratio is 1/(n+1), where n
is the value of timer latch. By writing a count value to the corresponding timer latch (addresses 00F016 to 00F316 : timers 1 to 4), the value
is also set to a timer, simultaneously.
The count value is decremented by 1. The timer interrupt request bit
is set to “1” by a timer overflow at the next count pulse, after the
count value reaches “0016.”
8.4.1 Timer 1
Timer 1 can select one of the following count sources:
• f(XIN)/16
• f(XIN)/4096
The count source of timer 1 is selected by setting bit 0 of timer 12
mode register 1 (address 00F416).
Timer interrupt request occurs at timer 1 overflow.
At reset, timers 3 and 4 are connected by hardware and “FF16” is
automatically set in timer 3; “0716” in timer 4. The f(XIN)/16 is selected as the timer 3 count source. The internal reset is released by
timer 4 overflow in this state and the internal clock is connected.
At execution of the STP instruction, timers 3 and 4 are connected by
hardware and “FF16” is automatically set in timer 3; “0716” in timer 4.
However, the f(XIN)/16 is not selected as the timer 3 count source.
So set both bit 0 of timer 34 mode register (address 00F516) and bit
6 at address 00C716 to “0” before execution of the STP instruction
(f(XIN)/16 is selected as the timer 3 count source). The internal STP
state is released by timer 4 overflow in this state and the internal
clock is connected.
As a result of the above procedure, the program can start under a
stable clock.
The timer-related registers is shown in Figures 8.4.1 and 8.4.2.
8.4.2 Timer 2
Timer 2 can select one of the following count sources:
• f(XIN)/16
• Timer 1 overflow signal
• External clock from the TIM2 pin
The count source of timer 2 is selected by setting bits 4 and 1 of
timer 12 mode register (address 00F4 16). When timer 1 overflow
signal is a count source for the timer 2, the timer 1 functions as an 8bit prescaler.
Timer 2 interrupt request occurs at timer 2 overflow.
8.4.3 Timer 3
Timer 3 can select one of the following count sources:
• f(XIN)/16
• External clock from the HSYNC pin
• External clock from the TIM3 pin
The count source of timer 3 is selected by setting bits 5 and 0 of
timer 34 mode register (address 00F516).
Timer 3 interrupt request occurs at timer 3 overflow.
8.4.4 Timer 4
Timer 4 can select one of the following count sources:
• f(XIN)/16
• f(XIN)/2
• Timer 3 overflow signal
The count source of timer 3 is selected by setting bits 1 and 4 of
timer 34 mode register (address 00F5 16). When timer 3 overflow
signal is a count source for the timer 4, the timer 3 functions as an 8bit prescaler.
Timer 4 interrupt request occurs at timer 4 overflow.
Rev. 1.0
24
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Timer 12 Mode Register
b7 b6 b5 b4 b3 b2 b1 b0
0
Timer mode register (T12M) [Address 00F416]
B
Name
Functions
After reset R W
0
Timer 1 count source 0: f(XIN)/16
selection bit 1 (T12M0) 1: f(XIN)/4096
0
R W
1
Timer 2 count source
selection bit (T12M1)
0: Interrupt clock source
1: External clock from TIM2 pin
0
R W
2 Timer 1 count
stop bit (T12M2)
0: Count start
1: Count stop
0
R W
3 Timer 2 count stop bit
(T12M3)
0: Count start
1: Count stop
0
R W
4 Timer 2 internal count
source selection bit 2
(T12M4)
0: f(XIN)/16
1: Timer 1 overflow
0
R W
0
R W
0
R —
5 Fix this bit to “0.”
6, 7 Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are “0.”
Fig. 8.4.1 Timer 12 Mode Register
Timer 34 Mode Register
b7 b6 b5 b4 b3 b2 b1 b0
Timer 34 mode register (T34M) [Address 00F516]
B
Name
0 Timer 3 count source
selection bit (T34M0)
1
Functions
0 : f(XIN)/16
1 : External clock source
After reset R W
0
R W
0 : Timer 3 overflow signal
1 : f(XIN)/16
0
R W
2 Timer 3 count stop bit
(T34M2)
0: Count start
1: Count stop
0
R W
3 Timer 4 count stop bit
(T34M3)
0: Count start
1: Count stop
0
R W
4 Timer 4 count source
selection bit (T34M4)
0: Internal clock source
1: f(XIN)/2
0
R W
0
R W
0
R —
5
Timer 4 internal
interrupt count source
selection bit (T34M1)
Timer 3 external count 0: TIM3 pin input
source selection bit
1: HSYNC pin input
(T34M5)
6, 7 Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are “0.”
Fig. 8.4.2 Timer 34 Mode Register
Rev. 1.0
25
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Data bus
8
Timer 1 latch (8)
1/4096
8
XIN
1/2
1/8
Timer 1
interrupt request
Timer 1 (8)
T12M0
T12M2
8
T12M4
8
Timer 2 latch (8)
8
TIM2
Timer 2
interrupt request
Timer 2 (8)
T12M1
T12M3
8
HSYNC
8
FF16
TIM3
T34M5
Reset
STP
instruction
Timer 3 latch (8)
8
Timer 3
interrupt request
Timer 3 (8)
T34M0
T34M2
8
8
Selection gate :
Connected to black
colored side at reset
0716
T34M1
Timer 4 latch (8)
T12M : Timer 12 mode register
T34M : Timer 34 mode register
8
Timer 4
interrupt request
Timer 4 (8)
T34M4
T34M3
8
Notes 1: “H” pulse width of external clock inputs TIM2 and TIM3 needs 4 machine cycles or more.
2: When the external clock source is selected, timers 2 and 3 are counted at a rising edge of input signal.
3: In the stop mode or the wait mode, external clock inputs TIM2 and TIM3 cannot be used.
Fig. 8.4.3 Timer Block Diagram
Rev. 1.0
26
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.5 SERIAL I/O
This microcomputer has a built-in serial I/O which can either transmit
or receive 8-bit data serially in the clock synchronous mode.
The serial I/O block diagram is shown in Figure 8.5.1. The synchronous clock I/O pin (SCLK), data output pin (SOUT), and data input pin
(SIN) also functions as port P4.
Bit 3 of the serial I/O mode register (address 00DC16) selects whether
the synchronous clock is supplied internally or externally (from the
SCLK pin). When an internal clock is selected, bits 1 and 0 select
whether f(XIN) or f(XCIN) is divided by 4, 16, 32, or 64. To use SIN pin
for serial I/O, set the corresponding bit of the port P2 direction register (address 00C516) to “0.”
The operation of the serial I/O is described below. The operation of
the serial I/O differs depending on the clock source; external clock or
internal clock.
Data bus
XIN
1/2
Frequency
divider
1/2
1/4 1/8
1/16
SM1
SM0
SM2
S
Synchronization circuit
Selection gate :
Connected to black
colored side at reset.
SM : Serial I/O mode register
P41 latch
SCLK
Serial I/O counter (8)
SM3
P40 latch
SOUT(/IN)
SM5 : LSB
SM3
Serial I/O interrupt
request
MSB
(See note)
SIN
SM6
Serial I/O shift register (8)
(Address 00DD 16)
8
Note : When the data is set in the serial I/O register (address 00DD 16), the register functions as the serial I/O shift register.
Fig. 8.5.1 Serial I/O Block Diagram
Rev. 1.0
27
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Internal clock : The serial I/O counter is set to “7” during the write
cycle into the serial I/O register (address 00DD16), and the transfer
clock goes HIGH forcibly. At each falling edge of the transfer clock
after the write cycle, serial data is output from the SOUT pin. Transfer
direction can be selected by bit 5 of the serial I/O mode register. At
each rising edge of the transfer clock, data is input from the SIN pin
and data in the serial I/O register is shifted 1 bit.
After the transfer clock has counted 8 times, the serial I/O counter
becomes “0” and the transfer clock stops at HIGH. At this time the
interrupt request bit is set to “1.”
External clock : The an external clock is selected as the clock source,
the interrupt request is set to “1” after the transfer clock has been
counted 8 counts. However, transfer operation does not stop, so the
clock should be controlled externally. Use the external clock of 1 MHz
or less with a duty cycle of 50%.
The serial I/O timing is shown in Figure 8.5.2. When using an external clock for transfer, the external clock must be held at HIGH for
initializing the serial I/O counter. When switching between an internal clock and an external clock, do not switch during transfer. Also,
be sure to initialize the serial I/O counter after switching.
Notes 1: On programming, note that the serial I/O counter is set by writing to
the serial I/O register with the bit managing instructions, such as SEB
and CLB.
2: When an external clock is used as the synchronous clock, write transmit data to the serial I/O register when the transfer clock input level is
HIGH.
Synchronous clock
Transfer clock
Serial I/O register
write signal
(See note)
Serial I/O output
SOUT
D0
D1
D2
D3
D4
D5
D6
D7
Serial I/O input
SIN
Interrupt request bit is set to “1”
Note : When an internal clock is selected, the SOUT pin is at high-impedance after transfer is completed.
Fig. 8.5.2 Serial I/O Timing (for LSB first)
Rev. 1.0
28
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Serial I/O Mode Register
b7 b6 b5 b4 b3 b2 b1 b0
0
Serial I/O mode register (SM) [Address 00DC16]
B
Name
0, 1 Internal synchronous
clock selection bits
(SM0, SM1)
Functions
b1 b0
After reset R W
0
R W
0 0: f(XIN)/4
0 1: f(XIN)/16
1 0: f(XIN)/32
1 1: f(XIN)/64
2
Synchronous clock
selection bit (SM2)
0: External clock
1: Internal clock
0
R W
3
Serial I/O port
selection bit (SM3)
0: P40, P41
1: SOUT(/IN), SCLK
0
R W
0
R W
4 Fix this bit to “0.”
5
Transfer direction
selection bit (SM5)
0: LSB first
1: MSB first
0
R W
6
Serial input pin
selection bit (SM6)
0: Input signal from SIN pin.
1: Input signal from SOUT pin.
0
R W
7
Nothing is assigned. This bit is a write disable bit.
When this bit is read out, the value is “0.”
0
R —
Fig. 8.5.3 Serial I/O Mode Register
Rev. 1.0
29
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.5.1 Serial I/O Common Transmission/Reception mode
By writing “1” to bit 6 of the serial I/O mode register, signals SIN and
SOUT are switched internally to be able to transmit or receive the
serial data.
Figure 8.5.4 shows signals on serial I/O common transmission/reception mode.
Note: When receiving the serial data after writing “FF16” to the serial I/O register.
SCLK
Clock
SOUT(/IN)
“1”
Serial I/O shift register (8)
SIN
“0”
SM6
SM : Serial I/O mode register
Fig. 8.5.4 Signals on Serial I/O Common Transmission/Reception Mode
Rev. 1.0
30
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.6 MULTI-MASTER I2C-BUS INTERFACE
Table 8.6.1 Multi-master I2C-BUS Interface Functions
The multi-master I2C-BUS interface is a serial communications circuit, conforming to the Philips I2C-BUS data transfer format. This
interface, offering both arbitration lost detection and a synchronous
functions, is useful for the multi-master serial communications.
Figure 8.6.1 shows a block diagram of the multi-master I2C-BUS interface and Table 8.6.1 shows multi-master I2C-BUS interface functions.
This multi-master I2C-BUS interface consists of the I2C address register, the I2C data shift register, the I2C clock control register, the I2C
control register, the I2C status register and other control circuits.
Item
Format
Communication mode
SCL clock frequency
Function
In conformity with Philips I2C-BUS
standard:
10-bit addressing format
7-bit addressing format
High-speed clock mode
Standard clock mode
In conformity with Philips I2C-BUS
standard:
Master transmission
Master reception
Slave transmission
Slave reception
16.1 kHz to 400 kHz (at φ = 4 MHz)
φ : System clock = f(XIN)/2
Note : We are not responsible for any third party’s infringement of patent rights
or other rights attributable to the use of the control function (bits 6 and 7
of the I2C control register at address 00DA16) for connections between
the I2C-BUS interface and ports (SCL1, SCL2, SDA1, SDA2).
b7
I2C address register (S0D) b0
Interrupt
generating
circuit
SAD6 SAD5 SAD4 SAD3 SAD2 SAD1 SAD0 RBW
Interrupt
request signal
(IICIRQ)
Address comparator
Serial
data
(SDA)
Noise
elimination
circuit
Data
control
circuit
b7
b0
2
I C data shift register
b7
S0
b0
AL AAS AD0 LRB
MST TRX BB PIN
2
AL
circuit
I C status
register (S1)
Internal data bus
BB
circuit
Serial
clock
(SCL)
Noise
elimination
circuit
Clock
control
circuit
b7
ACK
b0
ACK FAST CCR4 CCR3 CCR2 CCR1 CCR0
MODE
BIT
I2C clock control register (S2)
Clock division
b7
BSEL1 BSEL0 10BIT
SAD
b0
ALS
ESO BC2 BC1 BC0
I2C control register (S1D)
System clock (φ)
Bit counter
Fig. 8.6.1 Block Diagram of Multi-master I2C-BUS Interface
Rev. 1.0
31
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.6.1 I2C Data Shift Register
The I2C data shift register (S0 : address 00D716) is an 8-bit shift
register to store receive data and write transmit data.
When transmit data is written into this register, it is transferred to the
outside from bit 7 in synchronization with the SCL clock, and each
time one-bit data is output, the data of this register are shifted one bit
to the left. When data is received, it is input to this register from bit 0
in synchronization with the SCL clock, and each time one-bit data is
input, the data of this register are shifted one bit to the left.
The I2C data shift register is in a write enable status only when the
ESO bit of the I2C control register (address 00DA16) is “1.” The bit
counter is reset by a write instruction to the I2C data shift register.
When both the ESO bit and the MST bit of the I2C status register
(address 00D916) are “1,” the SCL is output by a write instruction to
the I2C data shift register. Reading data from the I2C data shift register is always enabled regardless of the ESO bit value.
Note: To write data into the I2C data shift register after setting the MST bit to
“0” (slave mode), keep an interval of 8 machine cycles or more.
I2C Data Shift Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C data shift register (S0) [Address 00D716 ]
B
0
to
7
Name
Functions
D0 to D7 This is an 8-bit shift register to store
receive data and write transmit data.
After reset
R W
Indeterminate
R W
Note: To write data into the I2C data shift register after setting the MST bit to
“0” (slave mode), keep an interval of 8 machine cycles or more.
Fig. 8.6.2 Data Shift Register
Rev. 1.0
32
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.6.2 I2C Address Register
The I2C address register (address 00D816) consists of a 7-bit slave
address and a read/write bit. In the addressing mode, the slave address written in this register is compared with the address data to be
received immediately after the START condition are detected.
(1) Bit 0: read/write bit (RBW)
Not used when comparing addresses, in the 7-bit addressing mode.
In the 10-bit addressing mode, the first address data to be received
is compared with the contents (SAD6 to SAD0 + RBW) of the I2C
address register.
The RBW bit is cleared to “0” automatically when the stop condition
is detected.
(2) Bits 1 to 7: slave address (SAD0–SAD6)
These bits store slave addresses. Regardless of the 7-bit addressing mode and the 10-bit addressing mode, the address data transmitted from the master is compared with the contents of these bits.
I2C Address Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C address register (S0D) [Address 00D816]
B
Name
Functions
0
Read/write bit
(RBW)
<Only in 10-bit addressing (in slave) mode>
The last significant bit of address data is
compared.
0: Wait the first byte of slave address after
START condition
(read state)
1: Wait the first byte of slave address after
RESTART condition
(write state)
1
to
7
Slave address
(SAD0 to SAD6)
<In both modes>
The address data is compared.
After reset R W
0
R —
0
R W
Fig. 8.6.3 I2C Address Register
Rev. 1.0
33
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.6.3 I2C Clock Control Register
(4) Bit 7: ACK clock bit (ACK)
The I2C clock control register (address 00DB16) is used to set ACK
control, SCL mode and SCL frequency.
This bit specifies a mode of acknowledgment which is an acknowledgment response of data transmission. When this bit is set to “0,”
the no ACK clock mode is set. In this case, no ACK clock occurs
after data transmission. When the bit is set to “1,” the ACK clock
mode is set and the master generates an ACK clock upon completion of each 1-byte data transmission.The device for transmitting
address data and control data releases the SDA at the occurrence of
an ACK clock (make SDA HIGH) and receives the ACK bit generated
by the data receiving device.
(1) Bits 0 to 4: SCL frequency control bits (CCR0–CCR4)
These bits control the SCL frequency.
(2) Bit 5: SCL mode specification bit (FAST MODE)
This bit specifies the SCL mode. When this bit is set to “0,” the standard clock mode is set. When the bit is set to “1,” the high-speed
clock mode is set.
(3) Bit 6: ACK bit (ACK BIT)
This bit sets the SDA status when an ACK clock✽ is generated. When
this bit is set to “0,” the ACK return mode is set and SDA goes to
LOW at the occurrence of an ACK clock. When the bit is set to “1,”
the ACK non-return mode is set. The SDA is held in the HIGH status
at the occurrence of an ACK clock.
However, when the slave address matches the address data in the
reception of address data at ACK BIT = “0,” the SDA is automatically
made LOW (ACK is returned). If there is a mismatch between the
slave address and the address data, the SDA is automatically made
HIGH (ACK is not returned).
Note: Do not write data into the I2C clock control register during transmission.
If data is written during transmission, the I2C clock generator is reset, so
that data cannot be transmitted normally.
✽ACK clock: Clock for acknowledgement
I2C Clock Control Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C clock control register (S2) [Address 00DB16]
B
0
to
4
Name
Functions
After reset R W
SCL frequency control bits Setup value of Standard clock High speed
(CCR0 to CCR4)
CCR4–CCR0
mode
clock mode
0 0 to 0 2
Setup disabled
04
Setup disabled
250
05
100
83.3
400 (See note)
333
166
...
500/CCR value 1000/CCR value
1D
17.2
34.5
1E
16.6
33.3
32.3
1F
R W
Setup disabled Setup disabled
03
06
0
16.1
(at φ = 4 MHz, unit : kHz)
5
SCL mode
specification bit
(FAST MODE)
0: Standard clock mode
1: High-speed clock mode
0
R W
6
ACK bit
(ACK BIT)
0: ACK is returned.
1: ACK is not returned.
0
R W
7
ACK clock bit
(ACK)
0: No ACK clock
1: ACK clock
0
R W
Note: At 400 kHz in the high-speed clock mode, the duty is as below .
“0” period : “1” period = 3 : 2
In the other cases, the duty is as below.
“0” period : “1” period = 1 : 1
Fig. 8.6.4 I2C Address Register
Rev. 1.0
34
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.6.4 I2C Control Register
(3) Bit 4: data format selection bit (ALS)
The I2C control register (address 00DA16) controls the data communication format.
This bit decides whether or not to recognize slave addresses. When
this bit is set to “0,” the addressing format is selected, so that address data is recognized. When a match is found between a slave
address and address data as a result of comparison or when a general call (refer to “8.6.5 I2C Status Register,” bit 1) is received, transmission processing can be performed. When this bit is set to “1,” the
free data format is selected, so that slave addresses are not recognized.
(1) Bits 0 to 2: bit counter (BC0–BC2)
These bits decide the number of bits for the next 1-byte data to be
transmitted. An interrupt request signal occurs immediately after the
number of bits specified with these bits are transmitted.
When a START condition is received, these bits become “0002” and
the address data is always transmitted and received in 8 bits.
(2) Bit 3: I2C interface use enable bit (ESO)
This bit enables usage of the multimaster I2C BUS interface. When
this bit is set to “0,” the use disable status is provided, so the SDA
and the SCL become high-impedance. When the bit is set to “1,” use
of the interface is enabled.
When ESO = “0,” the following is performed.
• PIN = “1,” BB = “0” and AL = “0” are set (they are bits of the I2C
status register at address 00D916 ).
• Writing data to the I2C data shift register (address 00D716) is disabled.
(4) Bit 5: addressing format selection bit (10BIT SAD)
This bit selects a slave address specification format. When this bit is
set to “0,” the 7-bit addressing format is selected. In this case, only
the high-order 7 bits (slave address) of the I2C address register (address 00D816) are compared with address data. When this bit is set
to “1,” the 10-bit addressing format is selected, all the bits of the I2C
address register are compared with address data.
(5) Bits 6 and 7: connection control bits between
I 2 C-BUS interface and ports
(BSEL0, BSEL1)
These bits controls the connection between SCL and ports or SDA
and ports (refer to Figure 8.6.5).
“0”
“1” BSEL0
SCL1/P11
SCL
Multi-master
I2C-BUS
interface
SDA
“0”
“1” BSEL1
SCL2/P12
“0”
“1” BSEL0
SDA1/P13
“0”
“1” BSEL1
SDA2/P14
Note: Set the corresponding direction register to “1” to use the
port as multi-master I2C-BUS interface.
Fig. 8.6.5 Connection Port Control by BSEL0 and BSEL1
Rev. 1.0
35
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
I2C Control Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C control register (S1D) [Address 00DA16]
B
Name
Functions
After reset R W
0
to
2
Bit counter
(Number of transmit/recieve
bits)
(BC0 to BC2)
b2
0
0
0
0
1
1
1
1
b0
0: 8
1: 7
0: 6
1: 5
0: 4
1: 3
0: 2
1: 1
0
R W
3
I2C-BUS interface use
enable bit (ESO)
0: Disabled
1: Enabled
0
R W
4
Data format selection
bit(ALS)
0: Addressing format
1: Free data format
0
R W
5
Addressing format selection
bit (10BIT SAD)
0: 7-bit addressing format
1: 10-bit addressing format
0
R W
b7 b6 Connection port (See note)
0 0: None
0 1: SCL1, SDA1
1 0: SCL2, SDA2
1 1: SCL1, SDA1, SCL2, SDA2
0
R W
6, 7 Connection control bits
between I2C-BUS interface
and ports
(BSEL0, BSEL1)
b1
0
0
1
1
0
0
1
1
Fig. 8.6.6 I2C Control Register
Rev. 1.0
36
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.6.5 I2C Status Register
(5) Bit 4: I2C-BUS interface interrupt request bit (PIN)
The I2C status register (address 00D916) controls the I2C-BUS interface status. The low-order 4 bits are read-only bits and the highorder 4 bits can be read out and written to.
This bit generates an interrupt request signal. Each time 1-byte data
is transmitted, the state of the PIN bit changes from “1” to “0.” At the
same time, an interrupt request signal is sent to the CPU. The PIN bit
is set to “0” in synchronization with a falling edge of the last clock
(including the ACK clock) of an internal clock and an interrupt request signal occurs in synchronization with a falling edge of the PIN
bit. When the PIN bit is “0,” the SCL is kept in the “0” state and clock
generation is disabled. Figure 8.6.8 shows an interrupt request signal generating timing chart.
The PIN bit is set to “1” in any one of the following conditions.
• Executing a write instruction to the I2C data shift register (address
00D716).
• When the ESO bit is “0”
• At reset
The conditions in which the PIN bit is set to “0” are shown below:
• Immediately after completion of 1-byte data transmission (including when arbitration lost is detected)
• Immediately after completion of 1-byte data reception
• In the slave reception mode, with ALS = “0” and immediately after
completion of slave address or general call address reception
• In the slave reception mode, with ALS = “1” and immediately after
completion of address data reception
(1) Bit 0: last receive bit (LRB)
This bit stores the last bit value of received data and can also be
used for ACK receive confirmation. If ACK is returned when an ACK
clock occurs, the LRB bit is set to “0.” If ACK is not returned, this bit is
set to “1.” Except in the ACK mode, the last bit value of received data
is input. The state of this bit is changed from “1” to “0” by executing a
write instruction to the I2C data shift register (address 00D716).
(2) Bit 1: general call detecting flag (AD0)
This bit is set to “1” when a general call✽ whose address data is all
“0” is received in the slave mode. By a general call of the master
device, every slave device receives control data after the general
call. The AD0 bit is set to “0” by detecting the STOP condition or
START condition.
✽General call: The master transmits the general call address “0016”
to all slaves.
(3) Bit 2: slave address comparison flag (AAS)
This flag indicates a comparison result of address data.
■ In the slave receive mode, when the 7-bit addressing format is
selected, this bit is set to “1” in one of the following conditions.
• The address data immediately after occurrence of a START condition matches the slave address stored in the high-order 7 bits
of the I2C address register (address 00D816).
• A general call is received.
■ In the slave reception mode, when the 10-bit addressing format is
selected, this bit is set to “1” with the following condition.
• When the address data is compared with the I2C address register (8 bits consists of slave address and RBW), the first bytes
match.
■ The state of this bit is changed from “1” to “0” by executing a write
instruction to the I2C data shift register (address 00D716).
(4) Bit 3: arbitration lost✽ detecting flag (AL)
n the master transmission mode, when a device other than the microcomputer sets the SDA to “L,”, arbitration is judged to have been
lost, so that this bit is set to “1.” At the same time, the TRX bit is set to
“0,” so that immediately after transmission of the byte whose arbitration was lost is completed, the MST bit is set to “0.” When arbitration
is lost during slave address transmission, the TRX bit is set to “0” and
the reception mode is set. Consequently, it becomes possible to receive and recognize its own slave address transmitted by another
master device.
✽Arbitration lost: The status in which communication as a master is
disabled.
(6) Bit 5: bus busy flag (BB)
This bit indicates the status of use of the bus system. When this bit is
set to “0,” this bus system is not busy and a START condition can be
generated. When this bit is set to “1,” this bus system is busy and the
occurrence of a START condition is disabled by the START condition
duplication prevention function (See note).
This flag can be written by software only in the master transmission
mode. In the other modes, this bit is set to “1” by detecting a START
condition and set to “0” by detecting a STOP condition. When the
ESO bit of the I2C control register (address 00DA16) is “0” and at
reset, the BB flag is kept in the “0” state.
(7) Bit 6: communication mode specification bit
(transfer direction specification bit: TRX)
This bit decides the direction of transfer for data communication. When
this bit is “0,” the reception mode is selected and the data of a transmitting device is received. When the bit is “1,” the transmission mode
is selected and address data and control data are output into the
SDA in synchronization with the clock generated on the SCL.
When the ALS bit of the I2C control register (address 00DA16) is “0”
in the slave reception mode is selected, the TRX bit is set to “1”
___
(transmit) if the least significant bit (R/W bit) of the address data trans___
mitted by the master is “1.” When the ALS bit is “0” and the R/W bit is
“0,” the TRX bit is cleared to “0” (receive).
The TRX bit is cleared to “0” in one of the following conditions.
• When arbitration lost is detected.
• When a STOP condition is detected.
• When occurence of a START condition is disabled by the START
condition duplication prevention function (Note).
• With MST = “0” and when a START condition is detected.
• With MST = “0” and when ACK non-return is detected.
• At reset
Rev. 1.0
37
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
(8) Bit 7: Communication mode specification bit
(master/slave specification bit: MST)
This bit is used for master/slave specification for data communication. When this bit is “0,” the slave is specified, so that a START
condition and a STOP condition generated by the master are received,
and data communication is performed in synchronization with the
clock generated by the master. When this bit is “1,” the master is
specified and a START condition and a STOP condition are generated, and also the clocks required for data communication are generated on the SCL.
The MST bit is cleared to “0” in one of the following conditions.
• Immediately after completion of 1-byte data transmission when
arbitration lost is detected
• When a STOP condition is detected.
• When occurence of a START condition is disabled by the START
condition duplication preventing function (Note).
• At reset
Note: The START condition duplication prevention function disables the START
condition generation, reset of bit counter reset, and SCL output, when
the following condition is satisfied:
a START condition is set by another master device.
I2C Status Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C status register (S1) [Address 00D916]
B
0
Name
Functions
Last receive bit (LRB)
(See note)
0 : Last bit = “0 ”
1 : Last bit = “1 ”
1
General call detecting flag
(AD0) (See note)
2
3
After reset R W
Indeterminate
R —
0 : No general call detected
1 : General call detected
(See note)
0
R —
Slave address comparison
flag (AAS) (See note)
0 : Address mismatch
1 : Address match
0
R —
Arbitration lost detecting flag
(AL) (See note)
0 : Not detected
1 : Detected
0
R —
1
R W
0 : Bus free
1 : Bus busy
0
R W
b7
0
0
1
1
0
R W
4
I2C-BUS interface interrupt
request bit (PIN)
5
Bus busy flag (BB)
6, 7 Communication mode
specification bits
(TRX, MST)
(See note)
(See note)
(See note)
0 : Interrupt request issued
1 : No interrupt request issued
b6
0 : Slave recieve mode
1 : Slave transmit mode
0 : Master recieve mode
1 : Master transmit mode
Note : These bits and flags can be read out, but cannnot be written.
Fig. 8.6.7 I2C Status Register
SCL
PIN
IICIRQ
Fig. 8.6.8 Interrupt Request Signal Generation Timing
Rev. 1.0
38
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.6.6 START Condition Generation Method
When the ESO bit of the I2C control register (address 00DA16) is “1,”
execute a write instruction to the I2C status register (address 00D916)
to set the MST, TRX and BB bits to “1.” A START condition will then
be generated. After that, the bit counter becomes “0002” and an SCL
for 1 byte is output. The START condition generation timing and BB
bit set timing are different in the standard clock mode and the highspeed clock mode. Refer to Figure 8.6.9 for the START condition
generation timing diagram, and Table 8.6.2 for the START condition/
STOP condition generation timing table.
I2C status register
write signal
SCL
Setup
time
SDA
Hold time
Set time for
BB flag
BB flag
Setup
time
Fig. 8.6.9 START Condition Generation Timing Diagram
8.6.7 STOP Condition Generation Method
When the ESO bit of the I2C control register (address 00DA16) is “1,”
execute a write instruction to the I2C status register (address 00D916)
for setting the MST bit and the TRX bit to “1” and the BB bit to “0”. A
STOP condition will then be generated. The STOP condition generation timing and the BB flag reset timing are different in the standard
clock mode and the high-speed clock mode. Refer to Figure 8.6.10
for the STOP condition generation timing diagram, and Table 8.6.2
for the START condition/STOP condition generation timing table.
I2C status register
write signal
SCL
SDA
BB flag
Setup
time
Hold time
Reset time for
BB flag
Fig. 8.6.10 STOP Condition Generation Timing Diagram
Table 8.6.2 START Condition/STOP Condition Generation Timing Table
Item
Standard Clock Mode
Setup time
5.0 µs (20 cycles)
(START condition)
Setup time
4.25 µs (17 cycles)
(STOP condition)
5.0 µs (20 cycles)
Hold time
Set/reset time
3.0 µs (12 cycles)
for BB flag
High-speed Clock Mode
2.5 µs (10 cycles)
1.75 µs (7 cycles)
2.5 µs (10 cycles)
1.5 µs (6 cycles)
Note: Absolute time at φ = 4 MHz. The value in parentheses denotes the
number of φ cycles.
Rev. 1.0
39
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.6.8 START/STOP Condition Detect Conditions
8.6.9 Address Data Communication
The START/STOP condition detect conditions are shown in
Figure 8.6.11 and Table 8.6.3. Only when the 3 conditions of Table
8.6.3 are satisfied, a START/STOP condition can be detected.
There are two address data communication formats, namely, 7-bit
addressing format and 10-bit addressing format. The respective address communication formats is described below.
Note: When a STOP condition is detected in the slave mode
(MST = 0), an interrupt request signal “IICIRQ” is generated to the
CPU.
(1) 7-bit addressing format
SCL release time
SCL
SDA
(START condition)
Setup
time
Hold time
Setup
time
Hold time
To meet the 7-bit addressing format, set the 10BIT SAD bit of the I2C
control register (address 00DA16) to “0.” The first 7-bit address data
transmitted from the master is compared with the high-order 7-bit
slave address stored in the I2C address register (address 00D816).
At the time of this comparison, address comparison of the RBW bit of
the I2C address register (address 00D816) is not made. For the data
transmission format when the 7-bit addressing format is selected,
refer to Figure 8.6.12, (1) and (2).
(2) 10-bit addressing format
SDA
(STOP condition)
Fig. 8.6.11 START Condition/STOP Condition Detect Timing Diagram
Table 8.6.3 START Condition/STOP Condition Detect Conditions
Standard Clock Mode
6.5 µs (26 cycles) < SCL
release time
3.25 µs (13 cycles) < Setup time
3.25 µs (13 cycles) < Hold time
High-speed Clock Mode
1.0 µs (4 cycles) < SCL
release time
0.5 µs (2 cycles) < Setup time
0.5 µs (2 cycles) < Hold time
Note: Absolute time at φ = 4 MHz. The value in parentheses denotes the number of φ cycles.
To meet the 10-bit addressing format, set the 10BIT SAD bit of the
I2C control register (address 00DA16) to “1.” An address comparison
is made between the first-byte address data transmitted from the
master and the 7-bit slave address stored in the I2C address register
(address 00D816). At the time of this comparison, an address comparison between the RBW bit of the I2C address register (address
00D816) and the R/W bit which is the last bit of the address data
transmitted from the master is made. In the 10-bit addressing mode,
the R/W bit which is the last bit of the address data not only specifies
the direction of communication for control data but also is processed
as an address data bit.
When the first-byte address data matches the slave address, the
AAS bit of the I2C status register (address 00D916) is set to “1.” After
the second-byte address data is stored into the I2C data shift register
(address 00D716), make an address comparison between the second-byte data and the slave address by software. When the address
data of the 2nd bytes matches the slave address, set the RBW bit of
the I2C address register (address 00D816) to “1” by software. This
processing can match the 7-bit slave address and R/W data, which
are received after a RESTART condition is detected, with the value
of the I2C address register (address 00D816). For the data transmission format when the 10-bit addressing format is selected, refer to
Figure 8.6.12, (3) and (4).
Rev. 1.0
40
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.6.10 Example of Master Transmission
8.6.11 Example of Slave Reception
An example of master transmission in the standard clock mode, at
the SCL frequency of 100 kHz and in the ACK return mode is shown
below.
➀ Set a slave address in the high-order 7 bits of the I2 C address
register (address 00D816) and “0” in the RBW bit.
➁ Set the ACK return mode and SCL = 100 kHz by setting “8516” in
the I2C clock control register (address 00DB16 ).
➂ Set “1016” in the I2C status register (address 00D916 ) and hold the
SCL at the HIGH.
④ Set a communication enable status by setting “4816 ” in the I2 C
control register (address 00DA16).
➄ Set the address data of the destination of transmission in the highorder 7 bits of the I 2C data shift register (address 00D716) and set
“0” in the least significant bit.
⑥ Set “F016 ” in the I2C status register (address 00D916) to generate
a START condition. At this time, an SCL for 1 byte and an ACK
clock automatically occurs.
⑦ Set transmit data in the I2C data shift register (address 00D716). At
this time, an SCL and an ACK clock automatically occurs.
➇ When transmitting control data of more than 1 byte, repeat step ➆.
➈ Set “D0 16” in the I2C status register (address 00D9 16). After this, if
ACK is not returned or transmission ends, a STOP condition will
be generated.
An example of slave reception in the high-speed clock mode, at the
SCL frequency of 400 kHz, in the ACK non-return mode, using the
addressing format, is shown below.
➀ Set a slave address in the high-order 7 bits of the I2C address
register (address 00D816 ) and “0” in the RBW bit.
➁ Set the no ACK clock mode and SCL = 400 kHz by setting “2516” in
the I2C clock control register (address 00DB16).
➂ Set “1016” in the I2C status register (address 00D916) and hold the
SCL at the HIGH.
④ Set a communication enable status by setting “4816 ” in the I2C
control register (address 00DA16).
➄ When a START condition is received, an address comparison is
made.
⑥ •When all transmitted address are“0” (general call):
AD0 of the I2C status register (address 00D916 ) is set to “1”and
an interrupt request signal occurs.
•When the transmitted addresses match the address set in ➀:
ASS of the I2C status register (address 00D916 ) is set to “1” and
an interrupt request signal occurs.
•In the cases other than the above:
AD0 and AAS of the I2C status register (address 00D9 16) are set
to “0” and no interrupt request signal occurs.
⑦ Set dummy data in the I 2C data shift register (address 00D716).
➇ When receiving control data of more than 1 byte, repeat step ➆.
➈ When a STOP condition is detected, the communication ends.
Rev. 1.0
41
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
S
Slave address R/W
A
Data
A
Data
A/A
P
A
P
Data
A
7 bits
“ 0”
1 to 8 bits
1 to 8 bits
(1) A master-transmitter transmits data to a slave-receiver
S
Slave address R/W
A
Data
A
Data
7 bits
“ 1”
1 to 8 bits
1 to 8 bits
(2) A master-receiver receives data from a slave-transmitter
S
Slave address
R/W
1st 7 bits
A
Slave address
2nd byte
A
Data
A/A
P
7 bits
“ 0”
8 bits
1 to 8 bits
1 to 8 bits
(3) A master-transmitter transmits data to a slave-receiver with a 10-bit address
S
Slave address
R/W
1st 7 bits
A
Slave address
2nd byte
A
Sr
Slave address
R/W
1st 7 bits
Data
7 bits
“ 0”
8 bits
7 bits
“1” 1 to 8 bits
(4) A master-receiver receives data from a slave-transmitter with a 10-bit address
S : START condition
A : ACK bit
Sr : Restart condition
P : STOP condition
R/W : Read/Write bit
A
Data
A
P
1 to 8 bits
From master to slave
From slave to master
Fig. 8.6.12 Address Data Communication Format
8.6.12 Precautions when using multi-master
I2C-BUS interface
(2) START condition generating procedure using multi-master
(1) Read-modify-write instruction
➀Procedure example (The necessary conditions of the generating
procedure are described as the following ➁ to ➄).
The precautions when the raead-modify-write instruction such as SEB,
CLB etc. is executed for each register of the multi-master I2C-BUS
interface are described below.
•I2C data shift register (S0)
When executing the read-modify-write instruction for this register
during transfer, data may become a value not intended.
•I2C address register (S0D)
When the read-modify-write instruction is executed for this register
at detecting the STOP condition, data may become a value not
______
intended. It is because hardware changes the read/write bit (RBW)
at the above timing.
•I2C status register (S1)
Do not execute the read-modify-write instruction for this register
because all bits of this register are changed by hardware.
•I2C control register (S1D)
When the read-modify-write instruction is executed for this register
at detecting the START condition or at completing the byte transfer,
data may become a value not intended. Because hardware changes
the bit counter (BC0–BC2) at the above timing.
•I2C clock control register (S2)
The read-modify-write instruction can be executed for this register.
•
•
—
LDA
SEI
BBS 5,S1,BUSBUSY
BUSFREE:
STA S0
LDM #$F0, S1
CLI
•
•
BUSBUSY:
CLI
•
•
(Taking out of slave address value)
(Interrupt disabled)
(BB flag confirming and branch process)
(Writing of slave address value)
(Trigger of START condition generating)
(Interrupt enabled)
(Interrupt enabled)
➁Use “STA,” “STX” or “STY” of the zero page addressing instruction
for writing the slave address value to the I2C data shift register.
➂Use “LDM” instruction for setting trigger of START condition generating.
④Write the slave address value of above ➁ and set trigger of START
condition generating of above ➂ continuously shown the above
procedure example.
➄Disable interrupts during the following three process steps:
• BB flag confirming
• Writing of slave address value
• Trigger of START condition generating
When the condition of the BB flag is bus busy, enable interrupts
immediately.
Rev. 1.0
42
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
(3) RESTART condition generating procedure
(4) STOP condition generating procedure
➀Procedure example (The necessary conditions of the generating
procedure are described as the following ➁ to ➅.)
Execute the following procedure when the PIN bit is “0.”
➀Procedure example (The necessary conditions of the generating
procedure are described as the following ➁ to ➃.)
LDM
LDA
SEI
STA
LDM
CLI
•
•
#$00, S1
—
S0
#$F0, S1
•
•
(Select slave receive mode)
(Taking out of slave address value)
(Interrupt disabled)
(Writing of slave address value)
(Trigger of RESTART condition generating)
(Interrupt enabled)
•
•
➁Select the slave receive mode when the PIN bit is “0.” Do not write
“1” to the PIN bit. Neither “0” nor “1” is specified for the writing to
the BB bit.
The TRX bit becomes “0” and the SDA pin is released.
➂The SCL pin is released by writing the slave address value to the
I 2C data shift register. Use “STA,” “STX” or “STY” of the zero page
addressing instruction for writing.
④Use “LDM” instruction for setting trigger of RESTART condition generating.
➄Write the slave address value of above ➂ and set trigger of RESTART condition generating of above ➃ continuously shown the
above procedure example.
⑥Disable interrupts during the following two process steps:
• Writing of slave address value
• Trigger of RESTART condition generating
SEI
LDM #$C0, S1
NOP
LDM #$D0, S1
CLI
•
•
(Interrupt disabled)
(Select master transmit mode)
(Set NOP)
(Trigger of STOP condition generating)
(Interrupt enabled)
➁Write “0” to the PIN bit when master transmit mode is select.
➂Execute “NOP” instruction after setting of master transmit mode.
Also, set trigger of STOP condition generating within 10 cycles after selecting of master trasmit mode.
④Disable interrupts during the following two process steps:
• Select of master transmit mode
• Trigger of STOP condition generating
(5) Writing to I2C status register
Do not execute an instruction to set the PIN bit to “1” from “0” and an
instruction to set the MST and TRX bits to “0” from “1” simultaneously.
It is because it may enter the state that the SCL pin is released and
the SDA pin is released after about one machine cycle. Do not execute an instruction to set the MST and TRX bits to “0” from “1” simultaneously when the PIN bit is “1.” It is because it may become the
same as above.
(6) Process of after STOP condition generating
Do not write data in the I2C data shift register S0 and the I2C status
register S1 until the bus busy flag BB becomes “0” after generating
the STOP condition in the master mode. It is because the STOP
condition waveform might not be normally generated. Reading to the
above registers do not have the problem.
Rev. 1.0
43
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.7 PWM OUTPUT FUNCTION
8.7.4 Operating of 14-bit PWM
This microcomputer is equipped with two 14-bit PWM (DA) and eight
8-bit PWMs (PWM0–PWM7). DA1 and DA2 have a 14-bit resolution
with the minimum resolution bit width of 0.25 µs and a repeat period
of 4096 µs (for f(XIN) = 8 MHz). PWM0–PWM7 have the same circuit
structure and an 8-bit resolution with minimum resolution bit width of
4 µs and repeat period of 1024 µs (for f(XIN) = 8 MHz).
Figure 8.7.1 shows the PWM block diagram. The PWM timing generating circuit applies individual control signals to DA and PWM0–
PWM7 using f(XIN) divided by 2 as a reference signal.
As with 8-bit PWM, set the bit 0 of PWM output control register 1
(address 00D516) to “0” (at reset, bit 0 is already set to “0” automatically), so that the PWM count source is supplied. Next, select the
output polarity by bit 2 of PWM output control register 2 (address
00D616). Then, the 14-bit PWM outputs from the DA output pin by
setting bit 1 of PWM output control register 1 to “0” (at reset, this bit
already set to “0” automatically) to select the DA output.
The output example of the 14-bit PWM is shown in Figure 8.7.3.
The 14-bit PWM divides the data of the DA latch into the low-order 6
bits and the high-order 8 bits.
The fundamental waveform is determined with the high-order 8-bit
data “DH.” A HIGH area with a length t ✕ DH (HIGH area of fundamental waveform) is output every short area of “t” = 256τ =
64 µs (τ is the minimum resolution bit width of 250 ns). The HIGH
level area increase interval (tm) is determined with the low-order 6-bit
data “DL.” The HIGH are of smaller intervals “tm” shown in Table 5 is
longer by t than that of other smaller intervals in PWM repeat period
“T” = 64t. Thus, a rectangular waveform with the different HIGH width
is output from the DA pins. Accordingly, the PWM output changes by
τ unit pulse width by changing the contents of the DA-H and DA-L
registers. A length of entirely HIGH cannot be output, i. e. 256/256.
8.7.1 Data Setting
When outputting DA, first set the high-order 8 bits to the DA-H register (address 00CE16), then the low-order 6 bits to the DA-L register
(address 00CF16). When outputting PWM0–PWM7, set 8-bit output
data to the PWMi register (i means 0 to 7; addresses 00D0 16 to
00D416, 00F616 to 00F816).
8.7.2 Transferring Data from Registers to PWM
Circuit
Data transfer from the 8-bit PWM register to the 8-bit PWM circuit is
executed at writing data to the register.
The signal output from the 8-bit PWM output pin corresponds to the
contents of this register.
Also, data transfer from the DA register (addresses 00CE 16 and
00CF16) to the 14-bit PWM circuit is executed at writing data to the
DA-L register (address 00CF16). Reading from the DA-H register
(address 00CE16) means reading this transferred data. Accordingly,
it is possible to confirm the data being output from the DA output pin
by reading the DA register.
8.7.3 Operating of 8-bit PWM
The following explains PWM operation.
First, set the bit 0 of PWM output control register 1 (address 00D516)
to “0” (at reset, bit 0 is already set to “0” automatically), so that the
PWM count source is supplied.
PWM0–PWM3 are also used as pins P60–P63, PWM4–PWM7 are
also used as ports P00–P03, respectively. For PWM0–PWM3, set
the corresponding bits of the ports P6 direction register to “1” (output
mode). For PWM4–PWM7, set those of the port P0 direction register to “1.” And select each output polarity by bit 3 of PWM output
control register 2 (address 00D616). Then, for PWM0–PWM5, set
bits 2 to 7 of PWM output control register 1 to “1” (PWM output). For
PWM6 and PWM7, set bits 0 and 1 of PWM output control register 2
to “1.”
The PWM waveform is output from the PWM output pins by setting
these registers.
Figure 8.7.2 shows the 8-bit PWM timing. One cycle (T) is composed of 256 (28) segments. The 8 kinds of pulses, relative to the
weight of each bit (bits 0 to 7), are output inside the circuit during 1
cycle. Refer to Figure 8.7.2 (a). The 8-bit PWM outputs waveform
which is the logical sum (OR) of pulses corresponding to the contents of bits 0 to 7 of the 8-bit PWM register. Several examples are
shown in Figure 8.7.2 (b). 256 kinds of output (HIGH area: 0/256 to
255/256) are selected by changing the contents of the PWM register. A length of entirely HIGH output cannot be output, i.e. 256/256.
8.7.5 Output after Reset
At reset, the output of ports P60–P63 and P00–P03 are in the highimpedance state, and the contents of the PWM register and the
PWM circuit are undefined. Note that after reset, the PWM output is
undefined until setting the PWM register.
Table 8.7.1 Relation Between the Low-order 6-bit Data and Highlevel Area Increase Interval
Low-order 6 bits of Data Area Longer by τ than That of Other tm (m = 0 to 63)
LSB
000000
000001
Nothing
000010
m = 16, 48
000100
m = 8, 24, 40, 56
001000
m = 4, 12, 20, 28, 36, 44, 52, 60
010000
m = 2, 6, 10, 14, 18, 22, 26, 30, 34, 38, 42, 46, 50, 54, 58, 62
100000
m = 1, 3, 5, 7, ................................. 57, 59, 61, 63
m = 32
Rev. 1.0
44
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Data bus
DA-H register
(Address : 00CE16 )
b7
b0
DA-L register (See note)
(Address : 00CF16 )
DA latch
(14 bits)
MSB
LSB
6
8
14
6
PN2
PN4
14-bit PWM circuit
DA
DA
PW1
XIN
PWM timing
generating
circuit
1/2
PW0
PWM register
(Address : 00D0 16)
b7
b0
8
PN3
P60
D60
PWM0
PW2
P61
D61
PWM1
D62
PWM2
D63
PWM3
D00
PWM4
D02
PWM5
D02
PWM6
D03
PWM7
8-bit PWM circuit
PWM1 register (Address : 00D1
16)
PW3
P62
PWM2 register (Address : 00D2
16)
PW4
P63
PWM3 register (Address : 00D3
16)
PW5
P00
Selection gate :
Connected to
black colored
side when reset.
16)
PW6
P02
PWM5 register (Address : 00F6
Pass gate
Inside of
with the others.
PWM4 register (Address : 00D4
16)
PW7
P02
is as same contents
PWM6 register (Address : 00D7
16)
PN0
P03
PW FPWM output control register 1
PN FPWM output control register 2
PWM7 register (Address : 00F8
16)
PN1
D0 FPort P0 direction register
D6 FPort P6 direction register
Note: The DA-L register also functions as the low-order 6 bits of the DA latch.
Fig. 8.7.1 PWM Block Diagram
Rev. 1.0
45
46
FF16 (255)
1816 (24)
0116 (1)
0016 (0)
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
t
2
4
6
8
12
10 14
13579
16
18
20
26
24
22
20
28
32
36
50
48
56
54 58
52
46 50
44
42
40
40
30 34 38
30
60
64
62 66
60
68
72
70 74
70
76
90
12 0
13 0
14 0
15 0
92
96
10 8
10 4
10 0
11 2
12 4
12 0
11 6
12 8
13 6
13 2
15 6
15 2
14 8
14 4
14 0
(b) Example of 8-bit PWM
t = 4 µs T = 1024 µs
f(XIN) = 8 MHz
T = 256 t
(a) Pulses showing the weight of each bit
88
11 0
16 0
17 0
18 0
19 0
20 0
21 0
22 0
23 0
24 0
25 0 25 5
16 0
16 4
16 8
17 2
17 6
18 0
18 4
18 8
19 2
19 6
20 0
21 2
20 8
20 4
21 6
22 4
22 0
22 8
23 2
23 6
24 0
24 4
24 8
25 2
94 98 102 106 110 114 118 122 126 130 134 138 142 146 150 154 158 162 166 170 174 178 182 186 190 194 198 202 206 210 214 218 222 226 230 234 238 242 246 250 254
10 0
PWM output
84
82 86 90
80
78
80
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Fig. 8.7.2 PWM Timing
Rev. 1.0
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Set “2816” to DA-L register.
Set “2C16” to DA-H register.
b7 b6 b5 b4 b3 b2 b1 b0
b7 b6 b5 b4 b3 b2 b1 b0
[DA-H
0 0 1 0 1 1 0 0 DH
register]
[DA-L register]
b13
0
b6 b5
0
1
0
1
1
0
0
These bits decide HIGH level area
of fundamental waveform.
HIGH level area of
fundamental waveform
Fundamental
waveform
Minimum
resolution bit
width 0.25 µs
✕
0
1
0
0
0
DL
At writing of DA-L
At writing of DA-L
[DA latch]
1
1
b0
0
1
0
0
0
These bits decide smaller interval “tm” in which HIGH leval
area is [HIGH level area of fundamental waveform + τ ].
High-order 8-bit
value of DA latch
Waveform of smaller interval “tm” specified by low-order 6 bits
0.25 µs✕44
0.25 µs✕45
0.25 µs
14-bit
… 03 02 01 00
PWM output 2C 2B 2A
14-bit
2C 2B 2A … 03 02 01 00
PWM output
8-bit
counter
8-bit
counter
FF FE FD … D6 D5 D4 D3 … 02 01 00
FF FE FD … D6 D5 D4 D3 … 02 01 00
Fundamental waveform of smaller interval
“tm” which is not specified by low-order 6
bits is not changed.
0.25 µs✕44
τ = 0.25 µs
14-bit PWM output
t0
t1
t2
t3
t4
t5
t59
t60
t61
t62
t63
Low-order 6-bit output of
DA latch
Repeat period
T = 4096 µs @
Fig. 8.7.3 14-bit PWM Timing (f(XIN) = 8 MHz)
Rev. 1.0
47
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
PWM Output Control Register 1
b7 b6 b5 b4 b3 b2 b1 b0
PWM output control register 1 (PW) [Address 00D516]
B
Name
Functions
0 DA, PWM count source 0 : Count source supply
1 : Count source stop
selection bit (PW0)
0 : DA output
1 DA/PN4 selection bit
1 : PN4 output
(PW1)
After reset R W
0
R W
0
R W
2 P60/PWM0 output
selection bit (PW2)
0: P60 output
1: PWM0 output
0
R W
3 P61/PWM1 output
selection bit (PW3)
0: P61 output
1: PWM1 output
0
R W
4 P62/PWM2 output
selection bit (PW4)
0: P62 output
1: PWM2 output
0
R W
5 P63/PWM3 output
selection bit (PW5)
0: P63 output
1: PWM3 output
0
R W
6 P00/PWM4 output
selection bit (PW6)
0: P00 output
1: PWM4 output
0
R W
7 P01/PWM5 output
selection bit (PW7)
0: P01 output
1: PWM5 output
0
R W
Fig. 8.7.4 PWM Output Control Register 1
PWM Output Control Register 2
b7 b6 b5 b4 b3 b2 b1 b0
PWM output control register 2 (PN) [Address 00D6
B
Name
0 P02/PWM6 output
selection bit (PN0)
Functions
0 : P0 2
1 : PWM6 output
1
P03/PWM7 output
selection bit (PN1)
2
16]
After reset R W
0
R W
0 : P0 3
1 : PWM7 output
0
R W
DA output polarity
selection bit (PN2)
0 : Positive polarity
1 : Negative polarity
0
R W
3
PWM output polarity
selection bit (PN3)
0 : Positive polarity
1 : Negative polarity
0
R W
4
DA general-purpose
output bit (PN4)
0 : Output LOW
1 : Output HIGH
0
R W
0
R —
5 Nothing is assigned. These bits are write disable bits.
to When these bits are read out, the values are “0.”
7
Fig. 8.7.5 PWM Output Control Register 2
Rev. 1.0
48
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.8 A-D COMPARATOR
A-D comparator consists of 6-bit D-A converter and comparator. A-D
comparator block diagram is shown in Figure 8.8.1.
The reference voltage “Vref” for D-A conversion is set by bits 0 to 5 of
the A-D control register (address 00EF16).
The comparison result of the analog input voltage and the reference
voltage “Vref” is stored in bit 4 of the A-D mode register (address
00EE16).
For A-D comparison, set “0” to corresponding bits of the direction
register to use ports as analog input pins. Write the data for select of
analog input pins to bits 0 to 2 of the A-D control register 1 and write
the digital value corresponding to Vref to be compared to the bits 0
to 5 of the A-D control register. The voltage comparison starts by
writing to the A-D control register 2, and it is completed after 16 machine cycles (NOP instruction ✕ 8).
Data bus
A-D mode register
Bits 0 to 2
A-D1
A-D2
A-D3
A-D4
A-D5
A-D6
A-D7
A-D8
Comparator control
A-D control
register
A-D mode
register
Analog
signal
switch
Comparator
Bit 4
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Switch tree
Resistor ladder
Fig. 8.8.1 A-D Comparator Block Diagram
Rev. 1.0
49
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
A-D Mode Register
b7 b6 b5 b4 b3 b2 b1 b0
A-D mode register (ADM) [Address 00EE16]
B
Name
Functions
0
to
2
Analog input pin selection
bits
(ADM0 to ADM2)
3
This bit is a write disable bit.
When this bit is read out, the value is “0.”
4
Storage bit of comparison
result (ADM4)
5
to
7
Nothing is assigned. This bits are write disable bits.
When these bits are read out, the values are “0.”
b2
0
0
0
0
1
1
1
1
b1
0
0
1
1
0
0
1
1
b0
0 : A-D1
1 : A-D2
0 : A-D3
1 : A-D4
0 : A-D5
1 : A-D6
0 : A-D7
1 : A-D8
0: Input voltage < reference voltage
1: Input voltage > reference voltage
After reset R W
0
R W
0
R —
Indeterminate
R —
0
R —
Fig. 8.8.2 A-D Mode Register
A-D Control Register
b7 b6 b5 b4 b3 b2 b1 b0
A-D control register (ADC) [Address 00EF16]
B
0
to
5
Name
D-A converter set bits
(ADC0 to ADC5)
Functions
b5
0
0
0
b4
0
0
0
b3
0
0
0
b2
0
0
0
b1
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
0
1
1
b0
0 : 1/128Vcc
1 : 3/128Vcc
0 : 5/128Vcc
After reset
R W
0
R W
0
R —
1 : 123/128Vcc
0 : 125/128Vcc
1 : 127/128Vcc
6, 7 Nothing is assigned. These bits are write disable bits.
When these bits are reed out, the values are “ 0.”
Fig. 8.8.3 A-D Control Register
Rev. 1.0
50
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.9 ROM CORRECTION FUNCTION
This can correct program data in ROM. Up to 2 addresses can be
corrected, a program for correction is stored in the ROM correction
memory in RAM as the top address. The ROM correction vectors are
2 vectors.
Vector 1 : address 02C016
Vector 2 : address 02E016
Set the address of the ROM data to be corrected into the ROM correction address register. When the value of the counter matches the
ROM data address in the ROM correction vector as the top address,
the main program branches to the correction program stored in the
ROM memory for correction. To return from the correction program
to the main program, the op code and operand of the JMP instruction
(total of 3 bytes) are necessary at the end of the correction program.
The ROM correction function is controlled by the ROM correction
enable register.
ROM correction address 1 (high-order) 021716
ROM correction address 1 (low-order)
021816
ROM correction address 2 (high-order) 021916
ROM correction address 2 (low-order)
021A16
Fig. 8.9.1 ROM Correction Address Registers
Notes 1: Specify the first address (op code address) of each instruction as the
ROM correction address.
2: Use the JMP instruction (total of 3 bytes) to return from the correction
program to the main program.
3: Do not set the same ROM correction address to vectors 1 and 2.
4: Only M37212M8-XXXSP and M37212EFSP/FP have ROM correction function.
ROM Correction Enable Register
b7 b6 b5 b4 b3 b2 b1 b0
0 0
ROM correction enable register (RCR) [Address 021B16]
B
Name
Functions
0
Vector 1 enable bit (RC0)
0: Disabled
1: Enabled
0
R W
1
Vector 2 enable bit (RC1)
0: Disabled
1: Enabled
0
R W
0
R W
0
R —
2, 3 Fix these bits to “0.”
4
to
7
Nothing is assigned. These bits are write disable bits. When
these bits are read out, the values are “0.”
After reset R W
Fig. 8.9.2 ROM Correction Enable Register
Rev. 1.0
51
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.10 OSD FUNCTIONS
Table 8.10.1 outlines the OSD functions. This microcomputer incorporates an OSD control circuit of 24 characters ✕ 2 lines. OSD is
controlled by the CRT control register. Up to 256 kinds of characters
can be displayed. The colors can be specified for each character and
up to 4 kinds of colors can be displayed on one screen. A combination of up to 8 colors can be obtained by using each output signal (R,
G, and B).
Characters are displayed in a 12 ✕ 16 dots configuration to obtain
smooth character patterns (refer to Figure 8.10.1).
The following shows the procedure how to display characters on the
CRT screen.
➀ Write the display character code in OSD RAM.
➁ Specify the display color by using the color register.
➂ Write the color register in which the display color is set in OSD
RAM.
④ Specify the vertical position by using the vertical position register.
➄ Specify the character size by using the character size register.
⑥ Specify the horizontal position by using the horizontal position
register.
⑦ Write the display enable bit to the designated block display flag of
the CRT control register. When this is done, the OSD starts according to the input of the VSYNC signal.
Table 8.10.1 Features of Each Display Mode
Parameter
Number of display characters
Dot structure
Kinds of characters
Kinds of character sizes
Attribute
Functions
24 characters ✕ 2 lines
12 ✕ 16 dots
256 kinds
3 kinds
Border (black)
Character font coloring
1 screen : 8 kinds (per character unit)
Character background coloring
1 screen : 8 kinds (per character unit)
OSD output
Display position
Display expansion (multiline display)
R, G, B
Horizontal: 64 levels, Vertical: 128 levels
Possible
Rev. 1.0
52
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
The OSD circuit has an extended display mode. This mode allows
multiple lines (3 lines or more) to be displayed on the screen by interrupting the display each time one line is displayed and rewriting data
in the block for which display is terminated by software.
Figure 8.10.1 shows the configuration of OSD character. Figure 8.10.2
shows the block diagram of the OSD circuit. Figure 8.10.3 shows the
CRT control register.
12 dots
16 dots
Fig. 8.10.1 Configuration of OSD Character Display Area
Rev. 1.0
53
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Clock for OSD
OSC1 OSC2
H S Y N C VS Y N C
Display
oscillation
circuit
C ontrolregisters forO S D
OSD Control circuit
Horizontal position register
Vertical position register
Character size register
Color register
CRT control register
CRT port control register
(address 00E016)
(addresses 00E116, 00E216)
(addresses 00E416)
(addresses 00E616 to 00E916)
(address 00EA16)
(address 00EC16)
OSD RAM
10 bits ~24 characters ~2 lines
OSD ROM
12 dots ~16 dots ~256 characters
Shift register
12-bit
Output circuit
Shift register
12-bit
R
G
B
O U T1
O U T2
Data bus
Fig. 8.10.2 Block Diagram of OSD Circuit
Rev. 1.0
54
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
CRT Control Register
b7 b6 b5 b4 b3 b2 b1 b0
CRT control register (CC) [Address 00EA 16]
B
Functions
Name
After reset R W
0
All-blocks display control
bit (CC0) (See note)
0 : All-blocks display off
1 : All-blocks display on
0
R W
1
Block 1 display control bit
(CC1)
0 : Block 1 display off
1 : Block 1 display on
0
R W
2
Block 2 display control bit
(CC2)
0 : Block 2 display off
1 : Block 2 display on
0
R W
3
to
6
Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are “0.”
0
R —
7
P10 /OUT2 pin switch bit
(CC7)
0
R W
0 : P10
1 : OUT2
Note: Display is controlled by logical product (AND) between the all-blocks display
control bit and each block control bit.
Fig. 8.10.3 CRT Control Register
Rev. 1.0
55
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.10.1 Display Position
The display positions of characters are specified in units called a
“block.” There are 2 blocks, blocks 1 and 2. Up to 24 characters can
be displayed in each block (refer to “8.10.3 Memory for OSD”).
The display position of each block can be set in both horizontal and
vertical directions by software.
The display start position in the horizontal direction can be selected
for all blocks in common from 64-step display positions in units of
4TC (TC = OSD oscillation cycle).
The display start position in the vertical direction for each block can
be selected from 128-step display positions in units of 4 scanning
lines.
Blocks are displayed in conformance with the following rules:
• Block 2 is displayed after the display of block 1 is completed (Figure
8.10.4 (a)).
• When the display position of block 1 is overlapped with that of block
2 (Figure 8.10.4 (b)), the block 1 is displayed on the front.
• When another block display position appears while one block is
displayed (Figure 8.10.4 (c)),only block 1 is displayed. Similarly,
when multiline display, block 1 is displayed after the display of block
2 is completed.
HR
CV1
Block 1
C V2
Block 2
(a) Example when each block is separated
HR
CV1 = CV2
Block 1
(Block 2 is not displayed)
(b) Example when block 2 overlaps with block 1
HR
CV1
CV2
Block 1
Block 2
← Not displayed
Block 1 (second)
← Not displayed
CV1
(c) Example when block 2 overlaps in process of block 1
Notes 1: CV1 or CV2 indicates the vertical display start position of display block 1 or 2.
2: HR indicates the horizontal display start position of display block 1 or 2.
Fig. 8.10.4 Display Position
Rev. 1.0
56
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
The vertical display start position is determined by counting the horizontal sync signal (HSYNC). At this time, when VSYNC and HSYNC are
positive polarity (negative polarity), it starts to count the rising edge
(falling edge) of HSYNC signal from after fixed cycle of rising edge
(falling edge) of VSYNC signal. So interval from rising edge (falling
edge) of VSYNC signal to rising edge (falling edge) of HSYNC signal
needs enough time (2 machine cycles or more) for avoiding jitter.
The polarity of HSYNC and VSYNC signals can select with the CRT
port control register (address 00EC16).
8 machine cycles
or more
VSYNC signal input
0.25 to 0.50 [µs]
( at f(XIN) = 8MHz)
VSYNC control
signal in
microcomputer
Period of counting
HSYNC signal
(See note 2)
HSYNC
signal input
8 machine cycles
or more
1
2
3
4
5
Not count
When bits 0 and 1 of the CRT port control register
(address 00EC16) are set to “1” (negative polarity)
Notes 1 : The vertical position is determined by counting falling edge of HSYNC
signal after rising edge of VSYNC control signal in the microcomputer.
2 : Do not generate falling edge of HSYNC signal near rising edge of
VSYNC control signal in microcomputer to avoid jitter.
3 : The pulse width of VSYNC and HSYNC needs 8 machine cycles or
more.
Fig. 8.10.5 Supplement Explanation for Display Position
Rev. 1.0
57
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
The vertical display start position for each block can be set in 512
steps (where each step is 1TH (TH: HSYNC cycle)) as values “0016” to
“7F16” in vertical position register i (i = 1 and 2) (addresses 00E116
and 00E216) The vertical position register i is shown in Figure 8.10.6.
Vertical Position Register i
b7 b6 b5 b4 b3 b2 b1 b0
Vertical position register i (CVi) (i = 1 and 2) [Addresses 00E1 16, 00E216]
B
Name
Functions
0
to
6
Vertical display start positions
(CVi : CVi0 to CVi6)
7
Nothing is assigned. This bit is a write disable bit.
When this bit is read out, the value is “0.”
128 steps (00 16 to 7F16 )
After reset
R W
Indeterminate R W
0
R —
Fig. 8.10.6 Vertical Position Register i
Rev. 1.0
58
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
The horizontal display start position is common to all blocks, and can
be set in 64 steps (where 1 step is 4TC, TC being the OSD oscillation
cycle) as values “0016” to “3F16” in bits 0 to 5 of the horizontal position register (address 00D116). The horizontal position register is
shown in Figure 8.10.7.
Horizontal Position Register
b7 b6 b5 b4 b3 b2 b1 b0
Horizontal position register (HR) [Address 00E0 16 ]
B
0
to
5
Name
Horizontal display start
positions (HR0 to HR5)
Functions
64 steps (0016 to 3F16)
6, 7 Nothing is assigned. These bits are write disable bits.
When thses bits are read out, the values are “0.”
After reset
R W
0
R W
0
R —
Fig. 8.10.7 Horizontal Position Register
Rev. 1.0
59
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.10.2 Character Size
The size of characters to be displayed can be from 3 sizes for each
block. Use the character size register (address 00E416) to set a character size. The character size of block 1 can be specified by using
bits 0 and 1 of the character size register; the character size of block
2 can be specified by using bits 2 and 3. Figure 8.10.8 shows the
character size register.
The character size can be selected from 3 sizes: minimum size, medium size and large size. Each character size is determined by the
number of scanning lines in the height (vertical) direction and the
oscillating cycle for display (TC) in the width (horizontal) direction.
The minimum size consists of [1 scanning line] ✕ [1TC]; the medium
size consists of [2 scanning lines] ✕ [2TC]; and the large size consists of [3 scanning lines] ✕ [3TC]. Table 8.10.2 shows the relation
between the set values in the character size register and the character sizes.
Character Size Register
b7 b6 b5 b4 b3 b2 b1 b0
Character size register (CS) [Address 00E4 16]
B
Name
Functions
After reset
R W
0, 1 Character size of block 1
selection bits
(CS10, CS11)
00 : Minimum size
01 : Medium size
10 : Large size
11 : Do not set.
Indeterminate R W
2,3 Character size of block 2
selection bits
(CS20,CS21)
00 : Minimum size
01 : Medium size
10 : Large size
11 : Do not set.
Indeterminate R W
4
to
7
Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are “0.”
0
R —
Fig. 8.10.8 Character Size Register
Rev. 1.0
60
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Minimum
Medium
Large
Horizontal display start position
Fig. 8.10.9 Display Start Position of Each Character Size (Horizontal Direction)
Table. 8.10.2 Relation between Set Values in Character Size Register and Character Sizes
Set values of character size register
Character
Width (horizontal) direction
size
TC: oscillating cycle for display
Height (vertical) direction
scanning lines
CSn1
CSn0
0
0
Minimum
1 TC
1
0
1
Medium
2 TC
2
1
0
Large
3 TC
3
1
1
This is not available
Note: The display start position in the horizontal direction is not affected by the character size. In other words, the horizontal
display start position is common to all blocks even when the character size varies with each block (refer to Figure 8.10.9).
Rev. 1.0
61
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.10.3 Clock for OSD
As a clock for display to be used for OSD, it is possible to select one
of the following 4 types.
• Main clock supplied from XIN pin
• Main clock supplied from XIN pin divided by I.5
• Clock from the ceramic resonator or the LC or oscillator from the
pins OSC1 and OSC2
• Clock from the ceramic resonator or the quartz-crystal oscillator
supplied from the pins OSC1 and OSC2.
This OSD clock for each block can be selected by the CRT clock
selection register (address 00ED16).
When selecting the main clock, set the oscillation frequency to
8 MHz.
CRT Clock Selection Register
b7 b6 b5 b4 b3 b2 b1 b0
0 0 0 0 0 0
CRT clock selection register (CK) [Address 00ED16]
B
Name
Functions
0, 1 CRT clock
Functions
b1 b0
selection bits 0 0 The clock for display is supplied by connecting RC
(CK0,CK1)
or LC across the pins OSC1 and OSC2.
0
1
1
After reset R W
0
R W
0
R W
1 Since the main clock is used as the
OSD oscillation
clock for display, the oscillation
frequency
frequency is limited. Because of this,
= f(XIN)
the character size in width (horizontal)
0
OSD oscillation
direction is also limited. In this case,
frequency
pins OSC1 and OSC2 are also used
= f(XIN)/1.5
as input ports P36 and P37 respectively.
1 The clock for OSD is supplied by connecting the
following across the pins OSC1 and OSC2.
• a ceramic resonator only for OSD and a feedback
resistor
• a quartz-crystal oscillator only for OSD and a
feedback resistor (See note)
2 to 7 Fix these bits to “0.”
Note: It is necessary to connect other ceramic resonator or quartz-crystal oscillator across the pins XIN and XOUT.
Fig. 8.10.10 Block Diagram of OSD Selection Circuit
Rev. 1.0
62
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.10.4 Memory for OSD
(1) OSD ROM (addresses 1000016 to 11FFF16)
There are 2 types of memory for OSD : OSD ROM (addresses
1000016 to 11FFF16) used to store character dot data and OSD RAM
(addresses 060016 to 06B716) used to specify the characters and
colors to be displayed.
The dot pattern data for OSD characters is stored in OSD ROM. To
specify the kinds of the character font, it is necessary to write the
character code (Table 8.10.3) into the OSD RAM.
The OSD ROM has a capacity of 8K bytes. Since 32 bytes are required for 1 character data, the ROM can stores up to 256 kinds of
characters.
The OSD ROM space is broadly divided into 2 areas. The [vertical
16 dots] ✕ [horizontal (left side) 8 dots] data of display characters are
stored in addresses 1000016 to 107FF16 and 1100016 to 117FF16 ;
the [vertical 16 dots] ✕ [horizontal (right side) 4 dots] data of display
characters are stored in addresses 1080016 to 10FFF16 and 1180016
to 11FFF16 (refer to Figure 8.10.11). Note however that the highorder 4 bits in the data to be written to addresses 1080016 to 10FFF16
and 1180016 to 11FFF16 must be set to “1” (by writing data “FX16”).
Data of the character font is specified shown in Figure 8.10.11.
10XX016
or
11XX016
10XXF 16
or
11XXF 16
b7
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
0
0
0
0
0
0
1
1
1
0
0
1
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
1
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
1
0
0
0
0
0
b0
0
0
0
0
0
1
1
1
0
0
1
0
0
0
0
0
10XX016
+80016
or
11XX016
+80016
10XXF 16
+80016
or
11XXF 16
+80016
b7
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
b3
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
b0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Fig. 8.10.11 Character Font Data Storing Address
Rev. 1.0
63
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Table 8.10.3 Character Code List (Partially Abbreviated)
Character code
Character data storage address
Left 8 dots lines
Right 4 dots lines
0016
1000016
to
1000F16
1080016
to
1080F16
0116
1001016
to
1001F16
1081016
to
1081F16
0216
1002016
to
1002F16
1082016
to
1082F16
0316
1003016
to
1003F16
1083016
to
1083F16
:
:
:
7E16
107E016
to
107EF16
10FE016
to
10FEF16
7F16
107F016
to
107FF16
10FF016
to
10FFF16
8016
1100016
to
1100F16
1180016
to
1180F16
8116
1101016
to
1101F16
1181016
to
1181F16
:
:
:
FD16
117D016
to
117DF16
11FD016
to
11FDF16
FE16
117E016
to
117EF16
11FE016
to
11FEF16
FF16
117F016
to
117FF16
11FF016
to
11FFF16
(2) OSD RAM (addresses 060016 to 06B716)
The OSD RAM is allocated at addresses 060016 to 06B716, and is
divided into a display character code specification part, and color
code specification part for each block. Table 8.10.4 shows the contents of the OSD RAM.
For example, to display 1 character position (the left edge) in block
1, write the character code in address 060016, write the color code at
068016.
The structure of the OSD RAM is shown in Figure 8.10.12.
Table 8.10.4 Contents of OSD RAM
Block
Block 1
Display Position (from left)
1st character
2nd character
3rd character
:
22nd character
23rd character
24th character
Not used
Block 2
1st character
2nd character
3rd character
:
22nd character
23rd character
24th character
Character Code Specification
060016
060116
060216
:
061516
061616
061716
061816
:
061F16
062016
062116
062216
:
063516
063616
063716
Color Specification
068016
068116
068216
:
069516
069616
069716
069816
:
069F16
06A016
06A116
06A216
:
06B516
06B616
06B716
Rev. 1.0
64
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Block 1
[Character specification]
7
0
1st character : 0600 16
to
24th character : 0617 16
Character code
Specify 256 characters (“00 16” to “FF16”)
[Color specification]
1st character : 0680 16
1
0
to
24th character : 0697 16
Color register specification
0 0 : Specifying color register 0
0 1 : Specifying color register 1
1 0 : Specifying color register 2
1 1 : Specifying color register 3
Block 2
[Character specification]
1st character : 0620 16
7
0
to
24th character : 0637 16
Character code
Specify 256 characters (“00 16” to “FF16”)
[Color specification]
1st character : 06A0 16
1
0
to
24th character : 06B7 16
Color register specification
0 0 : Specifying color register 0
0 1 : Specifying color register 1
1 0 : Specifying color register 2
1 1 : Specifying color register 3
Fig. 8.10.12 Bit structure of OSD RAM
Rev. 1.0
65
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.10.5 Color Register
The color of a displayed character can be specified by setting the
color to one of the 4 registers (CO0 to CO3: addresses 00E616 to
00E916) and then specifying that color register with the OSD RAM.
There are 3 color outputs; R, G and B. By using a combination of
these outputs, it is possible to set 8 colors. However, since only 4
color registers are available, up to 4 colors can be disabled at one
time.
R, G and B outputs are set by using bits 1 to 3 in the color register. Bit
5 is used to specify whether a character output or blank output. Bits
4, 6 and 7 are used to specify character background color. Figure
8.10.12 shows the color register.
Color Register i
b7 b6 b5 b4 b3 b2 b1 b0
Color regist er i (COi) (i = 0 to 3) [Addresses 00E616 to 00E916]
B
Name
@
Functions
After reset R W
0
Nothing is assigned. This bit is a write disable bit.
When this bit is read out, the value is “0.”
1
B signal output selection
bit (COi1)
0: No character is output
1: Character is output
Indeterminate R W
2
G signal output selection
bit (COi2)
0: No character is output
1: Character is output
Indeterminate R W
3
R signal output selection
bit (COi3)
0: No character is output
1: Character is output
Indeterminate R W
4
B signal output (background)
0: No background color is output Indeterminate R W
selection bit (COi4) (See note 1) 1: Background color is output
5
OUT1 signal output control bit
(COi5) (See notes 1, 2)
6
0: No background color is output Indeterminate R W
G signal output (background)
selection bit (COi6) (See note 1) 1: Background color is output
7
R signal output (background)
0: No background color is output Indeterminate R W
selection bit (COi7) (See note 2) 1: Background color is output
0: Character is output
1: Blank is output
0
R —
Indeterminate R W
Notes 1: When bit 5 =“0” and bit 4 = “1,” there is output same as a character or
border output from pin OUT1.
Do not set bit 5 = “0” and bit 4 = “0.”
2: When only bit 7 =“1” and bit 5 “0,” there is output from pin OUT2.
Fig. 8.10.13 Color Register i
Rev. 1.0
66
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Table 8.10.5 Display Example of Character Background Coloring (When Green Is Set for a Character and Blue Is Set for Background
Color)
Border selection register
Color register i
G output
B output
OUT1 output
Character output
OUT2 output
MD0 COi7 COi6 COi5 COi4 COi3 COi2 COi1
Green
0
0
✕
0
1
0
(Note 1)
1
0
No output
(See note 2)
No output
Same output as
character A
Video signal and character
color (green) are not mixed.
Green
0
1
✕
0
1
0
1
0
No output
Same output as Video signal and character
color (green) are not mixed.
character A
Blank output
Green
0
0
0
1
0
0
1
0
No output
(See note 2)
No output
Blank output
TV image of character
background is not displayed.
Green
0
0
0
1
1
0
1
Background
color
1
✕
✕
Blank output
TV image of character
background is not displayed.
Border
output
(Black)
0
1
0
1
0
No output
(See note 2)
Blue
0
Green
No output
(See note 2)
No output
Border output
(Black)
Video signal and character
color (green) are not mixed.
Green
1
0
0
1
0
0
1
0
Blank output
1
0
0
1
1
0
1
No output
(See note 2)
Black
No output
TV image of character
background is not displayed.
Border
output
(Black)
0
Green
Blue
Background
color – border
Blank output
No output
(See note 2)
TV image of character
background is not displayed.
Notes 1 : When COi5 = “0” and COi4 = “1,” there is output same as a character or border output from the OUT1 pin.
Do not set COi5 = “0” and COi4 = “0.”
2 : When only COi7 = “1” and COi5 = “0,” there is output from pin OUT2.
3 : The portion “A” in which character dots are displayed is not mixed with any TV video signal.
4 : The wavy-lined arrows in the Table denote video signals.
5 : n : 0 to 3, ✕ : 0 or 1
Rev. 1.0
67
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.10.6 Border
An border of 1 clock (1 dot) equivalent size can be added to a character to be displayed in both horizontal and vertical directions. The
border is output from the OUT pin. In this case, set bit 5 of a color
register to “0” (character is output).
Border can be specified in units of block by using the border selection register (address 00E516). Figure 8.10.14 shows the border selection register. Table 8.10.6 shows the relationship between the values set in the border selection register and the character border function.
Fig. 8.10.15 Example of Border
Border Selection Register
b7 b6 b5 b4 b3 b2 b1 b0
Border selection register (MD) [Address 00E5 16]
B
Name
Functions
After reset R W
0
Block 1 OUT1 output
0 : Same output as R, G, B is output Indeterminate R W
border selection bit (MD10) 1 : Border output
1
Nothing is assigned. This bit is a write disable bit.
When this bit is read out, the value is “0.”
2
Block 2 OUT1 output
0 : Same output as R, G, B is output Indeterminate R W
border selection bit (MD20) 1 : Border output
3
to
7
Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are “0.”
0
0
R —
R —
Fig. 8.10.14 Border Selection Register
Table 8.10.6 Relationship between Set Value in Border Selection Register and Character Border Function
Border selection register
MDn0
Functions
Example of output
0
Ordinary
R, G, B output
OUT1 output
1
Border including character
R, G, B output
OUT1 output
Rev. 1.0
68
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.10.7 Multiline Display
This microcomputer can ordinarily display 2 lines on the CRT screen
by displaying 2 blocks at different vertical positions. In addition, it can
display up to 16 lines by using OSD interrupts.
An OSD interrupt request occurs at the point at which display of each
block has been completed. In other words, when a scanning line
reaches the point of the display position (specified by the vertical
position registers) of a certain block, the character display of that
block starts, and an interrupt occurs at the point at which the scanning line exceeds the block.
Note: An OSD interrupt does not occur at the end of display when the block is
not displayed. In other words, if a block is set to off display by the display
control bit of the CRT control register (address 00EA16), an OSD interrupt request does not occur (refer to Figure 8.10.16).
Block 1 (on display)
“OSD interrupt request”
Block 1 (on display)
“OSD interrupt request”
Block 2 (on display)
“OSD interrupt request”
Block 2 (on display)
“OSD interrupt request”
Block 1’ (off display)
No
“OSD interrupt request”
Block 2’ (off display)
No
“OSD interrupt request”
Block 1’ (on display)
Block 2’ (on display)
“OSD interrupt request”
“OSD interrupt request”
On display (OSD interrupt request occurs
at the end of block display)
Off display (OSD interrupt request does
not occur at the end of block display)
Fig. 8.10.16 Note on Occurence of OSD Interrupt
Rev. 1.0
69
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.10.8 OSD Output Pin Control
The OSD output pins R, G, B and OUT1 can also function as ports
P52–P55. Set corresponding bit of the port P5 direction register (address 00CB16) to “0” to specify these pins as OSD output pins, or set
it to “1” to specify it as a general-purpose port P5.
The OUT2 can also function as port P10. Set bit 0 of the CRT port
control register (address 00EC16) to “1” (output mode). After that, set
bit 7 of the CRT port control register to “1” to specify the pin as OSD
output pin, or set it to “0” to specify as port P10.
The input polarity of the HSYNC, VSYNC and output polarity of signals
R, G, B, OUT1 and OUT2 can be specified with the CRT port control
register (address 00EC) . Set a bit to “0” to specify positive polarity;
set it to “1” to specify negative polarity (refer to Figure 8.11.13).
The CRT port control register is shown in Figure 8.10.17.
CRT Port Control Register
b7 b6 b5 b4 b3 b2 b1 b0
CRT port control register (CRTP) [Address 00EC16 ]
B
Name
Functions
After reset R W
0
HSYNC input polarity
switch bit (HSYC)
0 : Positive polarity input
1 : Negative polarity input
0
R W
1
VSYNC input polarity
switch bit (VSYC)
0 : Positive polarity input
1 : Negative polarity input
0
R W
2
R/G/B output polarity switch 0 : Positive polarity output
1 : Negative polarity output
bit (R/G/B)
0
R W
3
OUT2 output polarity
switch bit (OUT2)
0 : Positive polarity output
1 : Negative polarity output
0
R W
4
OUT1 output polarity
switch bit (OUT1)
0 : Positive polarity output
1 : Negative polarity output
0
R W
5
R signal output switch bit
(OP5)
0 : R signal output
1 : MUT E signal output
0
R W
6
G signal output switch
bit(OP6)
0 : G signal output
1 : MUT E signal output
0
R W
7
B signal output switch
bit(OP7)
0 : B signal output
1 : MUT E signal output
0
R W
Fig. 8.10.17 CRT Port Control Register
Rev. 1.0
70
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.10.9 Raster Coloring Function
An entire screen (raster) can be colored by setting the CRT port control register. Since each of the R, G, B, OUT1, and OUT2 pins can be
switched to raster coloring output, 8 raster colors can be obtained.
When the character color/the character background color overlaps
with the raster color, the color (R, G, B, OUT1, OUT2), specified for
the character color/the character background color, takes priority of
the raster color. This ensures that character color/character background color is not mixed with the raster color.
The example of raster coloring is shown in Figure 8.10.18.
: Character color “RED” (R + OUT1 + OUT2)
: Border color “BLACK” (OUT1 + OUT2)
: Background color “MAGENTA” (R + B + OUT1 + OUT2)
: Raster color “BLUE” (B + OUT1 + OUT2)
A
A'
HSYNC
OUT1
OUT2
R
Signals
across
A-A'
G
B
Fig. 8.10.18 Example of Raster Coloring
Rev. 1.0
71
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.11 SOFTWARE RUNAWAY DETECT FUNCTION
This microcomputer has a function to decode undefined instructions
to detect a software runaway.
When an undefined op-code is input to the CPU as an instruction
code during operation, the following processing is done.
➀ The CPU generates an undefined instruction decoding signal.
➁ The device is internally reset because of occurrence of the undefined instruction decoding signal.
➂ As a result of internal reset, the same reset processing as in the
case of ordinary reset operation is done, and the program restarts
from the reset vector.
Note, however, that the software runaway detecting function cannot
be invalid.
φ
SYNC
Address
Data
PC
?
01,S–1
01,S
?
PCH
PCL
01,S–2
PS
ADH,
ADL
FFFF16
FFFE16
ADL
ADH
Reset sequence
Undefined instruction decoding signal
occurs.Internal reset signal occurs.
: Undefined instruction decode
? : Invalid
PC : Program counter
S : Stack pointer
ADL, ADH: Jump destination address of reset
Fig. 8.11.1 Sequence at Detecting Software Runaway Detection
Rev. 1.0
72
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.12. RESET CIRCUIT
Poweron
When the oscillation of a quartz-crystal oscillator or a ceramic resonator is stable and the power source voltage is 5 V ± 10 %, hold the
RESET pin at LOW for 2 µs or more, then return is to HIGH. Then, as
shown in Figure 8.12.2, reset is released and the program starts form
the address formed by using the content of address FFFF 16 as the
high-order address and the content of the address FFFE16 as the
low-order address. The internal state of microcomputer at reset are
shown in Figures 8.2.3 to 8.2.6.
An example of the reset circuit is shown in Figure 8.12.1.
The reset input voltage must be kept 0.6 V or less until the power
source voltage surpasses 4.5 V.
4 .5 V
Power source voltage 0 V
0 .6 V
Reset input voltage 0 V
Vcc
1
5
M51 953AL
RESET
4
3
0.1 µF
Vss
Microcomputer
Fig. 8.12.1 Example of Reset Circuit
XIN
φ
RESET
Internal RESET
SYNC
Address
?
?
01, S
01, S-1 01, S-2
FFFE
FFFF
ADH,
ADL
Reset address from the vector table
Data
?
32768 count of XIN
clock cycle (See note 3)
?
?
?
?
ADL
ADH
Notes 1 : f(XIN) and f(φ) are in the relation : f(XIN) = 2·f (φ).
2 : A question mark (?) indicates an undefined state that
depends on the previous state.
3 : Immediately after a reset, timer 3 and timer 4 are
connected by hardware. At this time, “FF16” is set
in timer 3 and “0716” is set to timer 4. Timer 3 counts down
with f(XIN)/16, and reset state is released by the timer 4
overflow signal.
Fig. 8.12.2 Reset Sequence
Rev. 1.0
73
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.13 CLOCK GENERATING CIRCUIT
The built-in clock generating circuit is shown in Figure 8.13.3. When
the STP instruction is executed, the internal clock φ stops at HIGH.
At the same time, timers 3 and 4 are connected by hardware and
“FF16” is set in timer 3 and “0716” is set in the timer 4. Select f(XIN)/16
as the timer 3 count source (set bit 0 of the timer mode register 2 to
“0” before the execution of the STP instruction). Moreover, set the
timer 3 and timer 4 interrupt enable bits to disabled (“0”) before execution of the STP instruction). The oscillator restarts when external
interrupt is accepted. However, the internal clock φ keeps its HIGH
until timer 4 overflows, allowing time for oscillation stabilization when
a ceramic resonator or a quartz-crystal oscillator is used.
When the WIT instruction is executed, the internal clock φ stops in
the HIGH but the oscillator continues running. This wait state is released when an interrupt is accepted (See note). Since the oscillator
does not stop, the next instruction can be executed at once.
When returning from the stop or the wait state, to accept an interrupt,
set the corresponding interrupt enable bit to “1” before executing the
STP or the WIT instructions.
Microcomputer
XIN
XOUT
CIN
COUT
Fig. 8.13.1 Ceramic Resonator Circuit Example
Microcomputer
Note: In the wait mode, the following interrupts are invalid.
• VSYNC interrupt
• OSD interrupt
• All timers interrupts using TIM2 and TIM3 pins input as count source
• All timers interrupts using f(XIN)/2 as count source
• All timers interrupts using f(XIN)/4092 as count source
• f(XIN)/4096 interrupt
• Multi-master I2C-BUS interface interrupt
X IN
Vcc
External oscillation circuit
Vss
A circuit example using a ceramic resonator (or a quartz-crystal oscillator) is shown in Figure 8.13.1. Use the circuit constants in accordance with the resonator manufacture’s recommended values. A circuit example with external clock input is shown in Figure 8.13.2. Input the clock to the XIN pin, and open the XOUT pin.
Fig. 8.13.2 External Clock Input Circuit Example
Interrupt request
S
Interrupt disable
flag I
S
Q
Q
Reset
S
Q
Reset
STP instruction
Selection gate :
Connected to black
side at reset.
WIT
instruction
R
R
R
T34M :
Timer 34 mode register
STP
instruction
Internal clock φ
1/2
1/8
Timer 3
Timer 4
T34M0
T34M2
XIN
XOUT
Fig. 8.13.3 Clock Generating Circuit Block Diagram
Rev. 1.0
74
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
8.14 DISPLAY OSCILLATION CIRCUIT
8.16 ADDRESSING MODE
The OSD oscillation circuit has a built-in clock oscillation circuits, so
that a clock for OSD can be obtained simply by connecting an LC, an
RC, a ceramic resonator, or a quartz-crystal oscillator across the pins
OSC1 and OSC2. Which of the sub-clock or the OSD oscillation circuit is selected by setting bits 0 and 1 of the CRT clock selection
register (address 00ED16).
The memory access is reinforced with 17 kinds of addressing modes.
Refer to SERIES 740 <Software> User’s Manual for details.
8.17 MACHINE INSTRUCTIONS
There are 71 machine instructions. Refer to SERIES 740 <Soft- ware>
User’s Manual for details.
9. PROGRAMMING NOTES
OSC1
• The divide ratio of the timer is 1/(n+1).
• Even though the BBC and BBS instructions are executed immediately after the interrupt request bits are modified (by the program), those instructions are only valid for the contents before
the modification. At least one instruction cycle is needed (such as
an NOP) between the modification of the interrupt request bits
and the execution of the BBC and BBS instructions.
• After the ADC and SBC instructions are executed (in the decimal
mode), one instruction cycle (such as an NOP) is needed before
the SEC, CLC, or CLD instruction is executed.
• An NOP instruction is needed immediately after the execution of
a PLP instruction.
• In order to avoid noise and latch-up, connect a bypass capacitor
(≈ 0.1µF) directly between the VCC pin–VSS pin and the VCC pin–
CNVSS pin, using a thick wire.
OSC2
L
C1
C2
Fig. 8.14.1 Display Oscillation Circuit
8.15 AUTO-CLEAR CIRCUIT
When a power source is supplied, the auto-clear function will operate by connecting the following circuit to the RESET pin.
Circuit example 1
Vcc
RESET
Vss
Circuit example 2
RESET
Vcc
Vss
Note : Make the level change from “L” to “H” at the point at
which the power source voltage exceeds the specified
voltage.
Fig. 8.15.1 Auto-clear Circuit Example
Rev. 1.0
75
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
10. ABSOLUTE MAXIMUM RATINGS
Symbol
VCC, AVCC
VI
VI
VO
VO
IOH
IOL1
IOL2
IOL3
IOL4
Pd
Topr
Tstg
Parametear
Power source voltage VCC
Input voltage
CNVSS
Input voltage
P00–P07, P10–P17, P20–P27,
P30–P37, P40–P4
2, OSC1, XIN,
______
HSYNC, VSYNC, RESET
Output voltage
P10–P14, P20–P17, P30, P31,
P40, P41, R, G, B, OUT1, DA
XOUT, OSC2
Output voltage
P00–P07, P60–P63
Circuit current
R, G, B, OUT1, P10–P14,
P20–P27, P30, P31, DA
Circuit current
R, G, B, OUT1, P06, P07, P10,
P20–P23, P30, P31, P40, P41, DA
Circuit current
P11–P14
Circuit current
P00–P07, P60–P63
Circuit current
P24–P27
Conditions
All voltages are
based on VSS.
Output transistors
are cut off.
Ta = 25 °C
Power dissipation
Operating temperature
Storage temperature
Ratings
–0.3 to 6
–0.3 to 6
–0.3 to VCC + 0.3
Unit
V
V
V
–0.3 to VCC + 0.3
V
–0.3 to 13
0 to 1 (See note 1)
V
mA
0 to 2 (See note 2)
mA
0 to 6 (See note 2)
0 to 1 (See note 2)
0 to 10 (See note 3)
550
–10 to 70
–40 to 125
mA
mA
mA
mW
°C
°C
11. RECOMMENDED OPERATING CONDITIONS (Ta = –10 °C to 70 °C, VCC = 5 V ± 10 %, unless otherwise noted)
Symbol
VCC
VSS
VIH1
VIH2
VIL1
VIL2
VIL3
IOH
IOL1
IOL2
IOL3
IOL4
f(XIN)
fosc
fhs1
fhs2
fhs3
Parameter
Power source voltage (See note 4), During CPU, OSD operation
Power source voltage
HIGH input voltage
P00–P07, P10–P17, P20–P2
7, P30–P37,
______
SIN, SCLK, HSYNC, VSYNC, RESET, XIN,
OSC1, TIM2, TIM3, INT1–INT3
HIGH input voltage
SCL1, SCL2, SDA1, SDA2 (When using I2C-BUS)
LOW input voltage
P00–P07, P10–P17, P20–P27, P30–P37, P40–P42
LOW input voltage
SCL1, SCL2, SDA1, SDA2 (When using I2C-BUS)
______
LOW input voltage (See note 6)
HSYNC, VSYNC, RESET, TIM2, TIM3,
INT1–INT3, XIN, OSC1, SIN, SCLK
HIGH average output current (See note 1)
R, G, B, OUT1, DA, P10–P14,
P20–P27, P30, P31
LOW average output current (See note 2)
R, G, B, OUT1, DA, P10,
P20–P23, P30, P31, P40, P41
LOW average output current (See note 2)
P11–P14
LOW average output current (See note 2)
P00–P07, P60–P63
LOW average output current (See note 3)
P24–P27
Oscillation frequency (for CPU operation) (See note 5) XIN
Oscillation frequency (for OSD)
OSC1
Input frequency
TIM2, TIM3
Input frequency
SCLK
Input frequency
SCL1, SCL2
Min.
4.5
0
0.8VCC
Limits
Typ.
5.0
0
0.7VCC
0
0
0
7.9
5.0
Max.
5.5
0
VCC
VCC
0.4 VCC
0.3 VCC
0.2 VCC
8.0
Unit
V
V
V
V
V
V
V
1
mA
2
mA
6
1
10
8.1
8.0
100
1
400
mA
mA
mA
MHz
MHz
kHz
MHz
kHz
Rev. 1.0
76
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
12. ELECTRIC CHARACTERISTICS (VCC = 5 V ± 10 %, VSS = 0 V, f(XIN) = 8 MHz, Ta = –10 °C to 70 °C, unless otherwise noted)
Symbol
ICC
VOH
VOL
Parameter
Power source current
Test conditions
System operation
Stop mode
HIGH output voltage R, G, B, OUT1, DA, P10–P14,
P20–P27, P30, P31
LOW output voltage R, G, B, OUT1, DA, P10,
P20–P23, P30, P31, P40,
P41
LOW output voltage P24–P27
LOW output voltage P11–P14
LOW output voltage P00–P07, P60–P63
OSD OFF
OSD ON
OSD OFF
OSD ON
VCC = 5.5 V, f(XIN) = 0
VCC = 4.5 V
IOH = –0.5 mA
VCC = 4.5 V
IOL = 0.5 mA
Limits
Min.
VCC = 5.5 V,
f(XIN) = 4 MHz
VCC = 5.5 V,
f(XIN) = 8 MHz
Typ.
10
20
20
30
Max.
20
40
40
60
300
2.4
0.4
VCC = 4.5 V
IOL = 10.0 mA
VCC = 4.5 V IOL = 3 mA
IOL = 6 mA
VCC = 4.5 V
IOL = 0.5 mA
Unit
Test
circuit
mA
1
µA
V
V
2
3.0
0.4
0.6
0.4
______
RESET
VT+ – VT– Hysteresis
Hysteresis (See note 6) HSYNC, VSYNC, TIM2, TIM3,
INT1–INT3, SCL1, SCL2,
SDA1, SDA2, SIN, SCLK
______
HIGH input leak current RESET, P10–P17, P20–P27,
IIZH
P30–P37, P40–P42, HSYNC, VSYNC
______
LOW input leak current RESET, P00–P07, P10–P17,
IIZL
P20–P27, P30–P37, P40–P42,
P60–P63, HSYNC, VSYNC
HIGH
input
leak
current
P00–P07, P60–P63
IOZH
RBS
I2C-BUS·BUS
switch connection resistor
(between SCL1 and SCL2, SDA1 and SDA2)
VCC = 5.0 V
VCC = 5.0 V
0.5
0.5
0.7
1.3
V
VCC = 5.5 V
VI = 5.5 V
VCC = 5.5 V
VI = 0 V
5
µA
5
µA
4
VCC = 5.5 V
VI = 12 V
VCC = 4.5 V
10
µA
5
130
Ω
6
3
Notes 1: The total current that flows out of the IC must be 20 mA or less.
2: The total input current to IC (IOL1 + IOL2 + IOL3) must be 30 mA or less.
3: The total average input current for ports P24–P27 to IC must be 20 mA or less.
4: Connect 0.1 µF or more capacitor externally between the power source pins VCC–VSS so as to reduce power source noise.
Also connect 0.1 µF or more capacitor externally between the pins VCC–CNVSS.
5: Use a quartz-crystal oscillator or a ceramic resonator for the CPU oscillation circuit. When using the data slicer, use 8 MHz.
6: P15, P32–P35 have the hysteresis when these pins are used as interrupt input pins or timer input pins. P11–P14 have the hysteresis when these pins are
used as multi-master I2C-BUS interface ports. P40–P42 have the hysteresis when these pins are used as serial I/O pins.
7: Pin names in each parameter is described as below.
(1) Dedicated pins: dedicated pin names.
(2) Duble-/triple-function ports
• When the same limits: I/O port name.
• When the limits of functins except ports are different from I/O port limits: function pin name.
Rev. 1.0
77
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
+ Power source voltage
1
2
4.5 V
A
I cc
XIN
Vcc
V cc
8.00 MHz
OSC1
XOUT
Each output pin
OSC2
VOH
Vss
V
Vss
Pin VCC is made the operation state and is
measured the current, with a ceramic
resonator.
3
IOH
or
or
VO L
IOL
After setting each output pin to HIGH level when measuring VOH
and to LOW level when measuring VOL, each pin is measured.
5.0 V
4
5.5 V
Vcc
Vcc
IIZH
or
IIZL
Each input pin
Each input pin
A
Vss
Vss
5.5 V
5
6
4.5V
12 V
Vcc
Vcc
IOZH
Each output pin
IBS
SCL1 or SDA1
A
A
RB S
SCL2 or SDA2
VBS
Vss
Vss
After setting each output pin OFF state, each
pin is measured
RBS = VBS/IBS
Fig.12.1 Measure Circuits
Rev. 1.0
78
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
13. A-D COMPARISON CHARACTERISTICS
(VCC = 5 V ± 10 %, VSS = 0 V, f(XIN) = 8 MHz, Ta = 25 °C, unless otherwise noted)
Symbol
Parameter
Test conditions
Min.
Resolution
Absolute accuracy
—
—
0
Limits
Typ.
Max.
6
±2
±1
Unit
bits
LSB
14. MULTI-MASTER I2C-BUS BUS LINE CHARACTERISTICS
Symbol
tBUF
Standard clock mode High-speed clock mode
Unit
Min.
Max.
Min.
Max.
4.7
1.3
µs
4.0
0.6
µs
4.7
1.3
µs
1000
20+0.1Cb
300
ns
0
0
0.9
µs
4.0
0.6
µs
300
20+0.1Cb
300
ns
250
100
ns
4.7
0.6
µs
4.0
0.6
µs
Parameter
Bus free time
Hold time for START condition
LOW period of SCL clock
Rising time of both SCL and SDA signals
Data hold time
HIGH period of SCL clock
Falling time of both SCL and SDA signals
Data set-up time
Set-up time for repeated START condition
Set-up time for STOP condition
tHD; STA
tLOW
tR
tHD; DAT
tHIGH
tF
tSU; DAT
tSU; STA
tSU; STO
Note: Cb = total capacitance of 1 bus line
SDA
tHD;STA
tBUF
tLOW
P
tR
tSU;STO
tF
Sr
S
P
SCL
tHD;STA
tHD;DAT
tHIGH
tSU;DAT
tSU;STA
S : Start condition
Sr : Restart condition
P : Stop condition
Fig.14.1 Definition Diagram of Timing on Multi-master I2C-BUS
Rev. 1.0
79
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
15. PROM PROGRAMMING METHOD
The built-in PROM of the One Time PROM version (blank) and the
built-in EPROM version can be read or programmed with a generalpurpose PROM programmer using a special programming adapter.
Product
M37212EFSP
M37212EFFP
Name of Programming Adapter
PCA7406
PCA7420
The PROM of the One Time PROM version (blank) is not tested or
screened in the assembly process nor any following processes. To
ensure proper operation after programming, the procedure shown in
Figure 15.1 is recommended to verify programming.
Programming with
PROM programmer
Screening (Caution)
(150°C for 40 hours)
Verification with
PROM programmer
Functional check in target device
Caution : The screening temperature is far higher
than the storage temperature. Never
expose to 150°C exceeding 100 hours.
Fig. 15.1 Programming and Testing of One Time PROM Version
Rev. 1.0
80
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
16. DATA REQUIRED FOR MASK ORDERS
The following are necessary when ordering a mask ROM production:
• Mask ROM Order Confirmation Form
• Mark Specification Form
• Data to be written to ROM, in EPROM form (32-pin DIP Type 27C101,
three identical copies) or FDK
Rev. 1.0
81
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
17. MASK CONFIRMATION FORM
Mask ROM number
GZZ–SH55–23B < 91A0 >
740 FAMILY MASK ROM CONFIRMATION FORM
SINGLE-CHIP MICROCOMPUTER M37212M4-XXXSP
MITSUBISHI ELECTRIC
Receipt
Date:
Section head Supervisor
signature
signature
Note : Please fill in all items marked ✽.
Customer
Date
issued
Date :
Submitted by Supervisor
)
Issuance
signature
✽
TEL
(
Company
name
✽1. Confirmation
Three EPROMs are required for each pattern if this order is performed by EPROMs.
One floppy disk is required for each pattern if this order is performed by a floppy disk.
Ordering by EPROMs
If at least two of the three sets of EPROMs submitted contain identical data, we will produce masks based on this data.
We shall assume the responsibility for errors only if the mask ROM data on the products we produce differs from this
data. Thus, extreme care must be taken to verify the data in the submitted EPROMs.
Checksum code for entire EPROM
(hexadecimal notation)
EPROM type (indicate the type used)
27C101
EPROM address
000016 Product nameASCII code:
'M37212M4-'
000F161234567890123456
1234567890123456
1234567890123456
1234567890123456
C00016
Data ROM(16K)
FFFF16
1000016
Character ROM1-a
107FF16
1080016
Character ROM2-a
10FFF16
1100016
Character ROM1-b
117FF16
1180016
Character ROM2-b
11FFF16 1234567890123456
12000161234567890123456
1234567890123456
1234567890123456
1FFFF161234567890123456
(1)
Set “FF16” in the shaded area.
(1/3)
Rev. 1.0
82
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH55–23B < 91A0 >
740 FAMILY MASK ROM CONFIRMATION FORM
SINGLE-CHIP MICROCOMPUTER M37212M4-XXXSP
MITSUBISHI ELECTRIC
(2)
Write the ASCII codes that indicate the product name of “M37212M4–” to addresses 000016 to 000F16.
Addresses 000016 to 000F16 store the product name. Address
ASCII codes ‘M37212M4-’ are listed on the right.
000016
The addresses and data are in hexadecimal notation.
000116
‘M’ = 4D16
Address
000816
‘–’ = 2D16
000216
‘3’ = 3316
‘7’ = 3716
000916
000A16
FF16
FF16
Note: If the name of the product contained in the EPROMs does
000316
000416
‘2’ = 3216
‘1’ = 3116
000B16
000C16
FF16
FF16
not match the name on the mask ROM confirmation form,
the ROM processing is disabled. Please make sure the
000516
000616
‘2’ = 3216
‘M’ = 4D16
000D16
000E16
FF16
FF16
data is written correctly.
000716
‘4’ = 3416
000F16
FF16
Ordering by floppy disk
We will produce masks based on the mask files generated by the mask file generating utility. We shall assume the
responsibility for errors only if the mask ROM data on the products we produce differs from this mask file. Thus, extreme
care must be taken to verify the mask file in the submitted floppy disk.
The submitted floppy disk must be 3.5-inch 2HD type and DOS/V format. And the number of the mask files must be 1 in
one floppy disk.
File code
(hexadecimal notation)
Mask file name
.MSK (equal or less than eight characters)
✽2. Mark specification
Mark specification must be submitted using the correct form for the type of package being ordered. Fill the appropriate
mark specification form (52P4B for M37212M4-XXXSP) and attach to the mask ROM confirmation form.
✽3. Comments
(2/3)
Rev. 1.0
83
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH55–23B < 91A0 >
740 FAMILY MASK ROM CONFIRMATION FORM
SINGLE-CHIP MICROCOMPUTER M37212M4-XXXSP
MITSUBISHI ELECTRIC
Inputting the character ROM
Input the character ROM data by dividing it into character ROM1 and character ROM2.
The structure of character ROM ( divided into 12 516 dots font)
Example
(Note)
Write the character code "00 16" to "7F 16"
to Addresses 10000 16 to 10FFF 16.
Write the character code "80 16" to "FF 16"
to Addresses 11000 16 to 11FFF 16.
Character code
Ò1A16Ó
Character
ROM1
Character
ROM2
b7 b6 b5 b4 b3 b2 b1 b0
Example
b7 b6 b5 b4 b3 b2 b1 b0
0 016
0 416
0416
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0A16
0A16
1 116
1 116
1 116
2 016
2 016
3 F16
4 016
4 016
4 016
0 016
0 016
F16
101A0 16
to
Example 109A016
to
101AF 16
109AF16
F016
F016
F016
F016
F016
F016
F016
F016
F816
F816
F816
F416
F416
F416
F016
F016
(3/3)
Rev. 1.0
84
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH55–24B < 91A0 >
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM
SINGLE-CHIP MICROCOMPUTER M37212M6-XXXSP/FP
MITSUBISHI ELECTRIC
Receipt
Date:
Section head Supervisor
signature
signature
Note : Please fill in all items marked ✽.
Customer
Date
issued
Date :
Submitted by Supervisor
)
Issuance
signature
✽
TEL
(
Company
name
✽1. Confirmation
Specify the name of the product being ordered.
Three EPROMs are required for each pattern if this order is performed by EPROMs.
One floppy disk is required for each pattern if this order is performed by a floppy disk.
Microcomputer name :
M37212M6-XXXSP
M37212M6-XXXFP
Ordering by EPROMs
If at least two of the three sets of EPROMs submitted contain identical data, we will produce masks based on this data.
We shall assume the responsibility for errors only if the mask ROM data on the products we produce differs from this
data. Thus, extreme care must be taken to verify the data in the submitted EPROMs.
Checksum code for entire EPROM
(hexadecimal notation)
EPROM type (indicate the type used)
27C101
EPROM address
000016 Product nameASCII code:
'M37212M6-'
000F1612345678901234567
12345678901234567
12345678901234567
12345678901234567
A00016
Data ROM(24K)
FFFF16
1000016
Character ROM1-a
107FF16
1080016
Character ROM2-a
10FFF16
1100016
Character ROM1-b
117FF16
1180016
Character ROM2-b
11FFF1612345678901234567
12345678901234567
120001612345678901234567
12345678901234567
1FFFF1612345678901234567
(1)
Set “FF16” in the shaded area.
(1/3)
Rev. 1.0
85
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH55–24B < 91A0 >
740 FAMILY MASK ROM CONFIRMATION FORM
SINGLE-CHIP MICROCOMPUTER M37212M6-XXXSP/FP
MITSUBISHI ELECTRIC
(2)
Write the ASCII codes that indicate the product name of “M37212M6–” to addresses 000016 to 000F16.
Addresses 000016 to 000F16 store the product name.
Address
ASCII codes ‘M37212M6-’ are listed on the right.
The addresses and data are in hexadecimal notation.
Note: If the name of the product contained in the EPROMs does
not match the name on the mask ROM confirmation form,
the ROM processing is disabled. Please make sure the
data is written correctly.
Address
000016
000116
‘M’ = 4D16
‘3’ = 3316
000816
000916
‘–’ = 2D16
FF16
000216
000316
‘7’ = 3716
‘2’ = 3216
000A16
000B16
FF16
FF16
000416
000516
‘1’ = 3116
‘2’ = 3216
000C16
000D16
FF16
FF16
000616
000716
‘M’ = 4D16
‘6’ = 3616
000E16
000F16
FF16
FF16
Ordering by floppy disk
We will produce masks based on the mask files generated by the mask file generating utility. We shall assume the
responsibility for errors only if the mask ROM data on the products we produce differs from this mask file. Thus, extreme
care must be taken to verify the mask file in the submitted floppy disk.
The submitted floppy disk must be 3.5-inch 2HD type and DOS/V format. And the number of the mask files must be 1 in
one floppy disk.
File code
(hexadecimal notation)
Mask file name
.MSK (equal or less than eight characters)
✽2. Mark specification
Mark specification must be submitted using the correct form for the type of package being ordered. Fill the appropriate
mark specification form (52P4B for M37212M6-XXXSP , 80P6N for M37212M6-XXXFP) and attach to the mask ROM
confirmation form.
✽3. Comments
(2/3)
Rev. 1.0
86
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH55–24B < 91A0 >
740 FAMILY MASK ROM CONFIRMATION FORM
SINGLE-CHIP MICROCOMPUTER M37212M6-XXXSP/FP
MITSUBISHI ELECTRIC
Inputting the character ROM
Input the character ROM data by dividing it into character ROM1 and character ROM2.
The structure of character ROM(divided into 12 516 dots font)
Example
(Note)
Write the character code "00 16 " to "7F 16"
to Addresses 10000 16 to 10FFF 16.
Write the character code "80 16 " to "FF16 "
to Addresses 11000 16 to 11FFF 16.
Character code
Ò1A16Ó
Character
ROM1
Character
ROM2
b7 b6 b5 b4 b3 b2 b1 b0
Example
b7 b6 b5 b4 b3 b2 b1 b0
0 016
0 416
0416
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0A16
0A16
1 116
1 116
1 116
2 016
2 016
3 F16
4 016
4 016
4 016
0 016
0 016
Example
101A0 16
to
101AF 16
F16
F016
F016
F016
F016
F016
F016
F016
F016
F816
F816
F816
F416
F416
F416
F016
F016
109A016
to
109AF16
(3/3)
Rev. 1.0
87
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH55–42B < 91A0 >
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM
SINGLE-CHIP MICROCOMPUTER M37212M8-XXXSP
MITSUBISHI ELECTRIC
Receipt
Date:
Section head Supervisor
signature
signature
Note : Please fill in all items marked ✽.
Customer
Date
issued
Date :
Submitted by Supervisor
)
Issuance
signature
✽
TEL
(
Company
name
✽1. Confirmation
Three EPROMs are required for each pattern if this order is performed by EPROMs.
One floppy disk is required for each pattern if this order is performed by a floppy disk.
Ordering by EPROMs
If at least two of the three sets of EPROMs submitted contain identical data, we will produce masks based on this data.
We shall assume the responsibility for errors only if the mask ROM data on the products we produce differs from this
data. Thus, extreme care must be taken to verify the data in the submitted EPROMs.
Checksum code for entire EPROM
(hexadecimal notation)
EPROM type (indicate the type used)
27C101
EPROM address
000016 Product nameASCII code:
12345678901234567
'M37212M8-'
000F1612345678901234567
12345678901234567
12345678901234567
800016
Data ROM(32K)
FFFF16
1000016
Character ROM1-a
107FF16
1080016
Character ROM2-a
10FFF16
1100016
Character ROM1-b
117FF16
1180016
Character ROM2-b
11FFF1612345678901234567
12345678901234567
120001612345678901234567
12345678901234567
1FFFF1612345678901234567
(1)
Set “FF16” in the shaded area.
(1/3)
Rev. 1.0
88
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH55–42B < 91A0 >
740 FAMILY MASK ROM CONFIRMATION FORM
SINGLE-CHIP MICROCOMPUTER M37212M8-XXXSP
(2)
Write the ASCII codes that indicate the product name of “M37212M8–” to addresses 000016 to 000F16.
Addresses 000016 to 000F16 store the product name.
Address
000016
‘M’ = 4D16
Address
000816
‘–’ = 2D16
000116
000216
‘3’ = 3316
‘7’ = 3716
000916
000A16
FF16
FF16
Note: If the name of the product contained in the EPROMs does
000316
000416
‘2’ = 3216
‘1’ = 3116
000B16
000C16
FF16
FF16
not match the name on the mask ROM confirmation form,
the ROM processing is disabled. Please make sure the
000516
000616
‘2’ = 3216
‘M’ = 4D16
000D16
000E16
FF16
FF16
data is written correctly.
000716
‘8’ = 3816
000F16
FF16
ASCII codes ‘M37212M8-’ are listed on the right.
The addresses and data are in hexadecimal notation.
Ordering by floppy disk
We will produce masks based on the mask files generated by the mask file generating utility. We shall assume the
responsibility for errors only if the mask ROM data on the products we produce differs from this mask file. Thus, extreme
care must be taken to verify the mask file in the submitted floppy disk.
The submitted floppy disk must be 3.5-inch 2HD type and DOS/V format. And the number of the mask files must be 1 in
one floppy disk.
File code
(hexadecimal notation)
Mask file name
.MSK (equal or less than eight characters)
✽2. Mark specification
Mark specification must be submitted using the correct form for the type of package being ordered. Fill the appropriate
mark specification form (52P4B for M37212M8-XXXSP) and attach to the mask ROM confirmation form.
✽3. Comments
(2/3)
Rev. 1.0
89
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
GZZ–SH55–42B < 91A0 >
740 FAMILY MASK ROM CONFIRMATION FORM
SINGLE-CHIP MICROCOMPUTER M37212M8-XXXSP
MITSUBISHI ELECTRIC
Inputting the character ROM
Input the character ROM data by dividing it into character ROM1 and character ROM2.
The structure of character ROM (divided into 12 516 dots font)
Example
(Note)
Write the character code "00 16" to "7F 16"
to addresses 10000 16 to 10FFF 16.
Write the character code "80 16" to "FF 16"
to addresses 11000 16 to 11FFF 16.
Character code
Ò1A16Ó
Character
ROM1
Character
ROM2
b7 b6 b5 b4 b3 b2 b1 b0
Example
b7 b6 b5 b4 b3 b2 b1 b0
0 016
0 416
0416
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0A16
0A16
1 116
1 116
1 116
2 016
2 016
3 F16
4 016
4 016
4 016
0 016
0 016
Example
101A0 16
to
101AF 16
(3/3)
F16
F016
F016
F016
F016
F016
F016
F016
F016
F816
F816
F816
F416
F416
F416
F016
F016
109A016
to
109AF16
Rev. 1.0
90
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
18. MARK SPECIFICATION FORM
Rev. 1.0
91
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
80P6N (80-PIN QFP) MARK SPECIFICATION FORM
Mitsubishi IC catalog name
Please choose one of the marking types below (A, B, C), and enter the Mitsubishi IC catalog name and the special mark (if needed).
A. Standard Mitsubishi Mark
64
41
40
65
Mitsubishi IC catalog name
Mitsubishi product number
(6-digit, or 7-digit)
25
80
1
24
B. Customer’s Parts Number + Mitsubishi IC Catalog Name
64
41
40
65
25
80
1
24
Customer’s Parts Number
Note : The fonts and size of characters are standard Mitsubishi type.
Mitsubishi IC catalog name
Notes 1 : The mark field should be written right aligned.
2 : The fonts and size of characters are standard Mitsubishi type.
3 : Customer’s parts number can be up to 14 alphanumeric characters for capital letters, hyphens, commas, periods and so on.
4 : If the Mitsubishi logo
is not required, check the box below.
Mitsubishi logo is not required
C. Special Mark Required
64
41
65
40
80
25
1
Notes1 : If special mark is to be printed, indicate the desired layout of the mark in the left figure. The layout will be
duplicated technically as close as possible.
Mitsubishi product number (6-digit, or 7-digit) and Mask
ROM number (3-digit) are always marked for sorting the
products.
2 : If special character fonts (e,g., customer’s trade mark
logo) must be used in Special Mark, check the box below.
For the new special character fonts, a clean font original
(ideally logo drawing) must be submitted.
24
Special character fonts required
Rev. 1.0
92
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
19. ONE TIME PROM VERSION M37212EFSP/FP MARKING
M37212EFSP
XXXXXXX
XXXXXXX is mitsubishi lot number
M37212EFFP
XXXXXXX
XXXXXXX is mitsubishi lot number
Rev. 1.0
93
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
20. APPENDIX
Pin Configuration (TOP VIEW)
1
52
P52/R
VSYNC
P60/PWM0
2
51
3
50
P61/PWM1
4
49
P53/G
P54/B
P55/OUT1
P62/PWM2
P63/PWM3
5
48
P00/PWM4
P01/PWM5
7
P02/PWM6
9
P03/PWM7
P42/SIN/A-D5
P41/SCLK/A-D6
P40/SOUT(/IN)/A-D7
10
DA
P35/INT2/A-D4
P34/INT1
P33/TIM3
14
P32/TIM2
18
P24
P25
19
P26
P27
CNVSS
XIN
21
6
8
11
12
13
15
16
17
20
M37212M4/M6/M8-XXXSP, M37212EFSP
HSYNC
47
P20
P21
46
P22
45
P23
44
P04
43
P05
P06
42
41
40
39
38
37
36
35
34
33
32
P07
P10/OUT2/A-D8
P11/SCL1
P12/SCL2
P13/SDA1
P14/SDA2
P15/INT3/A-D1
P16/A-D2
P17/A-D3
P30
24
29
P31
RESET
OSC1/P36
XOUT
25
28
OSC2/P37
VSS
26
27
VC C
22
31
23
30
Outline 52P4B
Rev. 1.0
94
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
P21
41
42
NC
NC
NC
NC
43
44
45
P15/INT3/A-D1
P16/A-D2
P17/A-D3
46
47
48
49
50
51
52
54
53
56
55
P04
P05
P06
P07
P10/OUT2/A-D8
NC
P11/SCL1
P12/SCL2
P13/SDA1
P14/SDA2
NC
58
57
P22
P23
59
NC
60
61
62
63
64
NC
NC
NC
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
65
40
NC
P20
P55/OUT1
P54/B
P53/G
P52/R
66
39
67
38
P30
NC
P31
68
37
RESET
69
36
70
35
NC
NC
72
31
75
30
XOUT
76
29
77
28
78
27
79
26
80
25
XIN
CNVSS
P27
NC
NC
24
23
22
20
21
19
18
17
33
P32/TIM2
P24
P25
P26
NC
NC
NC
NC
16
15
14
13
12
P40/SOUT(/IN)/A-D7
DA
P35/INT2/A-D4
P34/INT1
P33/TIM3
11
9
10
8
7
6
5
4
NC
NC
NC
NC
P00/PWM4
P01/PWM5
P02/PWM6
P03/PWM7
NC
P42/SIN/A-D5
P41/SCLK/A-D6
1
P63/PWM3
32
74
M37212M6-XXXFP, M37212EFFP
3
P60/PWM0
P61/PWM1
P62/PWM2
NC
73
VCC
NC
NC
VSS
34
71
2
HSYNC
VSYNC
OSC1/P36
OSC2/P37
Outline 80P6N-A
Rev. 1.0
95
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Memory Map
■ M37212M4/M8-XXXSP, M37212M6-XXXSP/FP
000016
M37212M6XXXSP/FP
RAM
(384 bytes)
M37212M4XXXSP
RAM
(320 bytes)
00BF16
00C016
00FF16
010016
1000016
Zero page
SFR area
OSD ROM
(8K bytes)
11FFF16
017F16
01BF16
Not used
Not used
OSD RAM
(96 bytes)
(See note)
M37212M6XXXSP/FP
ROM
(24K bytes)
060016
06B716
Not used
A00016
C00016
M37212M4XXXSP
ROM
(16K bytes)
FF0016
FFDE16
FFFF16
Interrupt vector area
Special page
1FFFF16
Note: Refer to Table 8.10.3 OSD RAM.
Rev. 1.0
96
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
■ M37212M8-XXXSP, M37212EFSP/FP
000016
M37212EFSP
RAM
(1280 bytes)
M37212M8XXXSP
RAM
(576 bytes)
00BF16
00C016
00FF16
010016
01FF16
021716
1000016
Zero page
OSD ROM
(8K bytes)
SFR area
11FFF16
Not used
2 page register
021B16
Not used
02C016
ROM correction function
Vector 1: address 02C016
Vector 2: address 02E016
02E016
033F16
OSD RAM
(96 bytes)
(See note)
05FF16
060016
Not used
06B716
M37212EFSP
ROM
(62K bytes)
Not used
080016
800016
M37212M8XXXSP
ROM
(32K bytes)
FF0016
FFDE16
FFFF16
Interrupt vector area
Special page
1FFFF16
Note: Refer to Table 8.10.3 OSD RAM
Rev. 1.0
97
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Memory Map of Special Function
Register (SFR)
■ SFR area (addresses C016 to DF16)
State immediately after reset
Bit allocation
:
Name
0 : “0” immediately after reset
Function bit
:
1 : “1” immediately after reset
: No function bit
? : Indeterminate immediately
after reset
0 : Fix to this bit to “0”
(do not write to “1”)
1 : Fix to this bit to “1”
(do not write to “0”)
Address
Register
Bit allocation
State immediately after reset
b0 b7
b7
b0
C016 Port P0 (P0)
C116 Port P0 direction register (D0)
C216
C316
C416
C516
C616
C716
C816
C916
CA16
CB16
CC16
CD16
CE16
CF16
D016
D116
D216
D316
D416
D516
D616
D716
D816
D916
DA16
DB16
DC16
DD16
DE16
DF16
Port P1 (P1)
Port P1 direction register (D1)
Port P2 (P2)
Port P2 direction register (D2)
Port P3 (P3)
Port P3 direction register (D3)
P31D P30D
P41 P40
Port P4 (P4)
P41D P40D
Port P4 direction register (D4)
Port P5 (P5)
Port P5 direction register (D5)
P55
P54
P55
SEL
P54 P53 P52
SEL SEL SEL
P63 P62
Port P6 (P6)
P53 P52
1
1
0
0
0
0
0
0
0
0
0
?
0
0
?
0
0
0
0
P61 P60
1
1
DA-H register (DA-H)
DA-L register (DA-L)
PWM0 register (PWM0)
PWM1 register (PWM1)
PWM2 register (PWM2)
PWM3 register (PWM3)
PWM4 register (PWM4)
PWM output control register 1 (PW)
PW7 PW6 PW5 PW4 PW3 PW2 PW1 PW0
P N4 P N3 P N2 P N1 P N0
PWM output control register 2 (PN)
I2C data shift register (S0)
I2C address register (S0D)
I2C status register (S1)
I2 C
control register (S1D)
I2C clock control register (S2)
Serial I/O mode register (SM)
Serial I/O register (SIO)
D7
D6
D5
D4
D3
D2
D1
D0
SAD6 SAD5 SAD4 SAD3 SAD2 SAD1 SAD0 RBW
MST TRX BB
PIN
AL AAS AD0 LRB
BSEL1 BSEL0 10BIT ALS ESO BC2 BC1 BC0
SAD
ST
ACK ABCITK MFA
ODE CCR4 CCR3 CCR2 CCR1 CCR0
SM6 SM5
0
SM3 SM2 SM1 SM0
?
0016
?
0016
?
0016
?
0016
0 0
0 0
? ?
0016
0F16
0F16
?
? ?
?
?
?
?
?
0016
0016
?
0016
1 0
0016
0016
0016
?
?
?
?
?
?
?
?
0
?
?
0
?
?
?
0
0
?
Rev. 1.0
98
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
■ SFR area (addresses E016 to FF16)
State immediately after reset
Bit allocation
:
Name
0 : “0” immediately after reset
Function bit
:
1 : “1” immediately after reset
: No function bit
? : Indeterminate immediately
after reset
0 : Fix to this bit to “0”
(do not write to “1”)
1 : Fix to this bit to “1”
(do not write to “0”)
Address
Bit allocation
Register
State immediately after reset
b0 b7
b7
E016
E116
E216
E316
E416
E516
E616
E716
E816
E916
EA16
EB16
EC16
ED16
EE16
EF16
F016
F116
F216
F316
F416
F516
F616
F716
F816
F916
FA16
FB16
FC16
FD16
FE16
FF16
Horizontal position register (HR)
b0
HR5 HR4 HR3 HR2 HR1 HR0
Vertical position register 1 (CV1)
CV16 CV15 CV14 CV13 CV12 CV11 CV10
Vertical position register 2 (CV2)
CV26 CV25 CV24 CV23 CV22 CV21 CV20
CS21 CS20 CS11 CS10
Character size register (CS)
Border selection register (MD)
Color register 0 (CO0)
CO07 CO06 CO05 CO04 CO03 CO02 CO01
Color register 1 (CO1)
CO17 CO16 CO15 CO14 CO13 CO12 CO11
MD20
MD10
Color register 2 (CO2)
CO27 CO26 CO25 CO24 CO23 CO22 CO21
Color register 3 (CO3)
CO37 CO36 CO35 CO34 CO33 CO32 CO31
CRT control register (CC)
CC7
CRT port control register (CRTP)
OP7 OP6 OP5 OUT1 OUT2 R/G/B VSYC HSYC
CRT clock selection register (CK) 0
A-D mode register (ADM)
0
0
?
?
?
?
0
0
0
0
0
0
0
0
0
?
0
0
CC2 CC1 CC0
0
0
0
0
0
CK1 CK0
ADM2 ADM1 ADM0
ADM4
ADC5 ADC4 ADC3 ADC2 ADC1 ADC0
A-D control register (ADC)
Timer 1 (T1)
Timer 2 (T2)
Timer 3 (T3)
Timer 4 (T4)
0
Timer 12 mode register (T12M)
T12M4 T12M3 T12M2 T12M1 T12M0
T34M5 T34M4 T34M3 T34M2 T34M1 T34M0
Timer 34 mode register (T34M)
PWM5 register (PWM5)
PWM6 register (PWM6)
PWM7 register (PWM7)
Interrupt input polarity register (RE) 0
RE5 RE4 RE3
1
CPU mode register (CM)
Interrupt request register 1 (IREQ1) IT3R
IICR VSCR OSDR TM4R TM3R TM2R TM1R
Interrupt request register 2 (IREQ2) 0
Interrupt control register 1 (ICON1) IT3E
IICE VSCE OSDE TM4E TM3E TM2E TM1E
Interrupt control register 2 (ICON2)
1
1
1
1
0
0
MSE
0
0
S1R IT2R IT1R
MCSKR0
0
CM2
0
S1E IT2E IT1E
0016
? ?
? ?
0016
0 ?
0 0
0016
0016
0016
0016
0016
0016
0016
0016
? 0
0016
FF16
0716
FF16
0716
0016
0016
?
?
?
0016
?
FC16
0016
0016
0016
0 0
?
?
?
?
?
?
?
?
?
0
?
?
0
0
0
0
0
0
Rev. 1.0
99
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
■ 2 page register area (addresses 21716 to 21B16)
Bit allocation
:
Name
State immediately after reset
0 : “0” immediately after reset
Function bit
:
1 : “1” immediately after reset
: No function bit
? : Indeterminate immediately
after reset
0 : Fix to this bit to “0”
(do not write to “1”)
1 : Fix to this bit to “1”
(do not write to “0”)
Address
Register
21716 ROM correction address 1 (high-order)
21816 ROM correction address 1 (low-order)
21916 ROM correction address 2 (high-order)
21A16 ROM correction address 2 (low-order)
21B16 ROM correction enable register (RCR)
Bit allocation
State immediately after reset
b7
b0 b7
0
0
RCR1RCR0
b0
0016
0016
0016
0016
0016
Note: Only M37212M8-XXXSP and M37212EFSP/FP have 2 page register.
Rev. 1.0
100
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Internal State of Processor Status Register and
Program Counter at Reset
State immediately after reset
Bit allocation
:
Name
0 : “0” immediately after reset
Function bit
:
1 : “1” immediately after reset
: No function bit
? : Indeterminate immediately
after reset
0 : Fix to this bit to “0”
(do not write to “1”)
1 : Fix to this bit to “1”
(do not write to “0”)
Register
Bit allocation
State immediately after reset
b0 b7
b7
Processor status register (PS)
Program counter (PCH)
Program counter (PCL)
N
V
T
B
D
I
Z
C
b0
? ? ? ? ? 1 ? ?
Contents of address FFFF16
Contents of address FFFE16
Rev. 1.0
101
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Structure of Register
The figure of each register structure describes its functions, contents
at reset, and attributes as follows:
<Example>
Bit position
Bit attributes(Note 2)
Values immediately after reset release (Note 1)
CPU Mode Register
b7 b6 b5 b4 b3 b2 b1 b0
0 0
1 1
CPU mode register (CPUM) (CM) [Address 00FB16]
B
Name
0, 1 Processor mode bits
(CM0, CM1)
2
Stack page selection
bit (See note) (CM2)
Functions
b1 b0
0
0
1
1
A f t er r e R W
R W
0
0: Single-chip mode
1:
0:
Not available
1:
0: 0 page
1: 1 page
1
RW
3, 4 Fix these bits to “1.”
1
RW
5 Nothing is assigned. This bit is write disable bit.
When this bit is read out, the value is “1.”
b7 b6
C
6, 7 lock switch bits
(CM6, CM7)
0 0: f(XIN) = 8 MHz
0 1: f(XIN) = 12 MHz
1 0: f(XIN) = 16 MHz
1 1: Do not set
1
R W
0
RW
: Bit in which nothing is assigned
Notes 1: Values immediately after reset release
0 ••••••••••••••••••“0” after reset release
1 ••••••••••••••••••“1” after reset release
Indeterminate•••Indeterminate after reset
release
2: Bit attributes••••••The attributes of control register bits are classified into 3 types : read-only, write-only
and read and write. In the figure, these attributes are represented as follows :
R••••••Read
W••••••Write
W ••••••Write enabled
R ••••••Read enabled
– ••••••Read disabled
– ••••••Write disabled
✽ ••••••“0” can be set by software, but “1”
cannot be set.
Rev. 1.0
102
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Addresses 00C116, 00C316, 00C516
Port Pi Direction Register
b7 b6 b5 b4 b3 b2 b1 b0
Port Pi direction register (Di) (i=0,1,2) [Addresses 00C1 16, 00C316, 00C516]
B
0
Name
Functions
After reset R W
0 : Port Pi0 input mode
1 : Port Pi0 output mode
0
R W
1
0 : Port Pi1 input mode
1 : Port Pi1 output mode
0
R W
2
0 : Port Pi2 input mode
1 : Port Pi2 output mode
0
R W
3
0 : Port Pi3 input mode
1 : Port Pi3 output mode
0
R W
4
0 : Port Pi4 input mode
1 : Port Pi4 output mode
0
R W
5
0 : Port Pi5 input mode
1 : Port Pi5 output mode
0
R W
6
0 : Port Pi6 input mode
1 : Port Pi6 output mode
0
R W
7
0 : Port Pi7 input mode
1 : Port Pi7 output mode
0
R W
Port Pi direction register
Address 00C716
Port Pi Direction Register
b7 b6 b5 b4 b3 b2 b1 b0
Port Pi direction register (Di) (i = 3, 4) [Address 00C716, 00C916]
B
Name
0
Port Pi direction register
1
Functions
After reset R W
0 : Port Pi0 input mode
1 : Port Pi0 output mode
0
R W
0 : Port Pi1 input mode
1 : Port Pi1 output mode
0
R W
2 to 7 Nothing is assigned. These bits are write disable bits.
indeterminate R —
When these bits are read out, the values are indeterminate.
Rev. 1.0
103
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00CB16
Port P5 Direction Register
b7 b6 b5 b4 b3 b2 b1 b0
Port P5 direction register (D5) [Address 00CB16]
b
Name
Functions
After reset R W
0, 1 Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are “0.”
0
R —
2
Port P52 output signal
selection bit (P52SEL)
0 : R signal output
1 : Port P52 output
0
R W
3
Port P53 output signal
selection bit (P53SEL)
0 : G signal output
1 : Port P53 output
0
R W
4
Port P54 output signal
selection bit (P54SEL)
0 : B signal output
1 : Port P54 output
0
R W
5
Port P55 output signal
selection bit (P55SEL)
0 : OUT1 signal output
1 : Port P55 output
0
R W
6,7 Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are “0.
Indeterminate R —
Address 00D516
PWM Output Control Register 1
b7 b6 b5 b4 b3 b2 b1 b0
PWM output control register 1 (PW) [Address 00D516]
B
Name
Functions
0 DA, PWM count source 0 : Count source supply
1 : Count source stop
selection bit (PW0)
0 : DA output
1 DA/PN4 selection bit
1 : PN4 output
(PW1)
After reset R W
0
R W
0
R W
2 P60/PWM0 output
selection bit (PW2)
0: P60 output
1: PWM0 output
0
R W
3 P61/PWM1 output
selection bit (PW3)
0: P61 output
1: PWM1 output
0
R W
4 P62/PWM2 output
selection bit (PW4)
0: P62 output
1: PWM2 output
0
R W
5 P63/PWM3 output
selection bit (PW5)
0: P63 output
1: PWM3 output
0
R W
6 P00/PWM4 output
selection bit (PW6)
0: P00 output
1: PWM4 output
0
R W
7 P01/PWM5 output
selection bit (PW7)
0: P01 output
1: PWM5 output
0
R W
Rev. 1.0
104
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00D616
PWM Output Control Register 2
b7 b6 b5 b4 b3 b2 b1 b0
PWM output control register 2 (PN) [Address 00D6
B
Name
0 P02/PWM6 output
selection bit (PN0)
Functions
0 : P0 2
1 : PWM6 output
1
P03/PWM7 output
selection bit (PN1)
2
16]
After reset R W
0
R W
0 : P0 3
1 : PWM7 output
0
R W
DA output polarity
selection bit (PN2)
0 : Positive polarity
1 : Negative polarity
0
R W
3
PWM output polarity
selection bit (PN3)
0 : Positive polarity
1 : Negative polarity
0
R W
4
DA general-purpose
output bit (PN4)
0 : Output LOW
1 : Output HIGH
0
R W
0
R —
5 Nothing is assigned. These bits are write disable bits.
to When these bits are read out, the values are “0.”
7
Address 00D716
I2C Data Shift Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C data shift register (S0) [Address 00D716 ]
B
0
to
7
Name
Functions
D0 to D7 This is an 8-bit shift register to store
receive data and write transmit data.
After reset
R W
Indeterminate
R W
Note: To write data into the I2C data shift register after setting the MST bit to
“0” (slave mode), keep an interval of 8 machine cycles or more.
Address 00D816
I2C Address Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C address register (S0D) [Address 00D816]
B
Name
Functions
After reset R W
0
Read/write bit
(RBW)
<Only in 10-bit addressing (in slave) mode>
The last significant bit of address data is
compared.
0: Wait the first byte of slave address after
START condition
(read state)
1: Wait the first byte of slave address after
RESTART condition
(write state)
0
R —
1
to
7
Slave address
(SAD0 to SAD6)
<In both modes>
The address data is compared.
0
R W
Rev. 1.0
105
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00D916
I2C Status Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C status register (S1) [Address 00D916]
B
0
Name
Functions
Last receive bit (LRB)
(See note)
0 : Last bit = “0 ”
1 : Last bit = “1 ”
1
General call detecting flag
(AD0) (See note)
2
3
After reset R W
Indeterminate
R —
0 : No general call detected
1 : General call detected
(See note)
0
R —
Slave address comparison
flag (AAS) (See note)
0 : Address mismatch
1 : Address match
0
R —
Arbitration lost detecting flag
(AL) (See note)
0 : Not detected
1 : Detected
0
R —
1
R W
0 : Bus free
1 : Bus busy
0
R W
b7
0
0
1
1
0
R W
4
I2C-BUS interface interrupt
request bit (PIN)
5
Bus busy flag (BB)
6, 7 Communication mode
specification bits
(TRX, MST)
(See note)
(See note)
(See note)
0 : Interrupt request issued
1 : No interrupt request issued
b6
0 : Slave recieve mode
1 : Slave transmit mode
0 : Master recieve mode
1 : Master transmit mode
Note : These bits and flags can be read out, but cannnot be written.
Address 00DA16
I2C Control Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C control register (S1D) [Address 00DA16]
B
Name
Functions
After reset R W
0
to
2
Bit counter
(Number of transmit/recieve
bits)
(BC0 to BC2)
b2
0
0
0
0
1
1
1
1
b0
0: 8
1: 7
0: 6
1: 5
0: 4
1: 3
0: 2
1: 1
0
R W
3
I2C-BUS interface use
enable bit (ESO)
0: Disabled
1: Enabled
0
R W
4
Data format selection
bit(ALS)
0: Addressing format
1: Free data format
0
R W
5
Addressing format selection
bit (10BIT SAD)
0: 7-bit addressing format
1: 10-bit addressing format
0
R W
b7 b6 Connection port (See note)
0 0: None
0 1: SCL1, SDA1
1 0: SCL2, SDA2
1 1: SCL1, SDA1, SCL2, SDA2
0
R W
6, 7 Connection control bits
between I2C-BUS interface
and ports
(BSEL0, BSEL1)
b1
0
0
1
1
0
0
1
1
Rev. 1.0
106
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00DB16
I2C Clock Control Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C clock control register (S2) [Address 00DB16]
B
0
to
4
Name
Functions
After reset R W
SCL frequency control bits Setup value of Standard clock High speed
(CCR0 to CCR4)
CCR4–CCR0
mode
clock mode
0 0 to 0 2
0
R W
Setup disabled Setup disabled
03
Setup disabled
04
Setup disabled
250
05
100
83.3
400 (See note)
06
333
166
...
500/CCR value 1000/CCR value
1D
17.2
34.5
1E
16.6
33.3
32.3
16.1
1F
(at φ = 4 MHz, unit : kHz)
5
SCL mode
specification bit
(FAST MODE)
0: Standard clock mode
1: High-speed clock mode
0
R W
6
ACK bit
(ACK BIT)
0: ACK is returned.
1: ACK is not returned.
0
R W
7
ACK clock bit
(ACK)
0: No ACK clock
1: ACK clock
0
R W
Note: At 400 kHz in the high-speed clock mode, the duty is as below .
“0” period : “1” period = 3 : 2
In the other cases, the duty is as below.
“0” period : “1” period = 1 : 1
Address 00DC16
Serial I/O Mode Register
b7 b6 b5 b4 b3 b2 b1 b0
0
Serial I/O mode register (SM) [Address 00DC16]
B
Name
0, 1 Internal synchronous
clock selection bits
(SM0, SM1)
Functions
b1 b0
After reset R W
0
R W
0 0: f(XIN)/4
0 1: f(XIN)/16
1 0: f(XIN)/32
1 1: f(XIN)/64
2
Synchronous clock
selection bit (SM2)
0: External clock
1: Internal clock
0
R W
3
Serial I/O port
selection bit (SM3)
0: P40, P41
1: SOUT(/IN), SCLK
0
R W
0
R W
4 Fix this bit to “0.”
5
Transfer direction
selection bit (SM5)
0: LSB first
1: MSB first
0
R W
6
Serial input pin
selection bit (SM6)
0: Input signal from SIN pin.
1: Input signal from SOUT pin.
0
R W
7
Nothing is assigned. This bit is a write disable bit.
When this bit is read out, the value is “0.”
0
R —
Rev. 1.0
107
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00E016
Horizontal Position Register
b7 b6 b5 b4 b3 b2 b1 b0
Horizontal position register (HR) [Address 00E0 16 ]
B
0
to
5
Name
Horizontal display start
positions (HR0 to HR5)
Functions
After reset
R W
0
R W
0
R —
64 steps (0016 to 3F16)
6, 7 Nothing is assigned. These bits are write disable bits.
When thses bits are read out, the values are “0.”
Addresses 00E116 and 00E216
Vertical Position Register i
b7 b6 b5 b4 b3 b2 b1 b0
Vertical position register i (CVi) (i = 1 and 2) [Addresses 00E1 16, 00E216]
B
Name
Functions
0
to
6
Vertical display start positions
(CVi : CVi0 to CVi6)
7
Nothing is assigned. This bit is a write disable bit.
When this bit is read out, the value is “0.”
128 steps (00 16 to 7F16 )
After reset
R W
Indeterminate R W
0
R —
Address 00E416
Character Size Register
b7 b6 b5 b4 b3 b2 b1 b0
Character size register (CS) [Address 00E4 16]
B
Name
Functions
After reset
R W
0, 1 Character size of block 1
selection bits
(CS10, CS11)
00 : Minimum size
01 : Medium size
10 : Large size
11 : Do not set.
Indeterminate R W
2,3 Character size of block 2
selection bits
(CS20,CS21)
00 : Minimum size
01 : Medium size
10 : Large size
11 : Do not set.
Indeterminate R W
4
to
7
Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are “0.”
0
R —
Rev. 1.0
108
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00E516
Border Selection Register
b7 b6 b5 b4 b3 b2 b1 b0
Border selection register (MD) [Address 00E5 16]
B
Name
Functions
After reset R W
Indeterminate R W
0
Block 1 OUT1 output
0 : Same output as R, G, B is output
border selection bit (MD10) 1 : Border output
1
Nothing is assigned. This bit is a write disable bit.
When this bit is read out, the value is “0.”
2
Block 2 OUT1 output
0 : Same output as R, G, B is output Indeterminate R W
border selection bit (MD20) 1 : Border output
3
to
7
Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are “0.”
0
0
R —
R —
Addresses 00E616 to 00E916
Color Register i
b7 b6 b5 b4 b3 b2 b1 b0
Color regist er i (COi) (i = 0 to 3) [Addresses 00E616 to 00E916]
B
Name
@
Functions
After reset R W
0
Nothing is assigned. This bit is a write disable bit.
When this bit is read out, the value is “0.”
1
B signal output selection
bit (COi1)
0: No character is output
1: Character is output
Indeterminate R W
2
G signal output selection
bit (COi2)
0: No character is output
1: Character is output
Indeterminate R W
3
R signal output selection
bit (COi3)
0: No character is output
1: Character is output
Indeterminate R W
4
B signal output (background)
0: No background color is output Indeterminate R W
selection bit (COi4) (See note 1) 1: Background color is output
5
OUT1 signal output control bit
(COi5) (See notes 1, 2)
6
0: No background color is output Indeterminate R W
G signal output (background)
selection bit (COi6) (See note 1) 1: Background color is output
7
R signal output (background)
0: No background color is output Indeterminate R W
selection bit (COi7) (See note 2) 1: Background color is output
0: Character is output
1: Blank is output
0
R —
Indeterminate R W
Notes 1: When bit 5 =“0” and bit 4 = “1,” there is output same as a character or
border output from pin OUT1.
Do not set bit 5 = “0” and bit 4 = “0.”
2: When only bit 7 =“1” and bit 5 “0,” there is output from pin OUT2.
Rev. 1.0
109
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00EA16
CRT Control Register
b7 b6 b5 b4 b3 b2 b1 b0
CRT control register (CC) [Address 00EA 16]
B
Functions
Name
After reset R W
0
All-blocks display control
bit (CC0) (See note)
0 : All-blocks display off
1 : All-blocks display on
0
R W
1
Block 1 display control bit
(CC1)
0 : Block 1 display off
1 : Block 1 display on
0
R W
2
Block 2 display control bit
(CC2)
0 : Block 2 display off
1 : Block 2 display on
0
R W
3
to
6
Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are “0.”
0
R —
7
P10 /OUT2 pin switch bit
(CC7)
0
R W
0 : P10
1 : OUT2
Note: Display is controlled by logical product (AND) between the all-blocks display
control bit and each block control bit.
Addresses 00EC16
CRT Port Control Register
b7 b6 b5 b4 b3 b2 b1 b0
CRT port control register (CRTP) [Address 00EC16 ]
B
Name
Functions
After reset R W
0
HSYNC input polarity
switch bit (HSYC)
0 : Positive polarity input
1 : Negative polarity input
0
R W
1
VSYNC input polarity
switch bit (VSYC)
0 : Positive polarity input
1 : Negative polarity input
0
R W
2
R/G/B output polarity switch 0 : Positive polarity output
1 : Negative polarity output
bit (R/G/B)
0
R W
3
OUT2 output polarity
switch bit (OUT2)
0 : Positive polarity output
1 : Negative polarity output
0
R W
4
OUT1 output polarity
switch bit (OUT1)
0 : Positive polarity output
1 : Negative polarity output
0
R W
5
R signal output switch bit
(OP5)
0 : R signal output
1 : MUT E signal output
0
R W
6
G signal output switch
bit(OP6)
0 : G signal output
1 : MUT E signal output
0
R W
7
B signal output switch
bit(OP7)
0 : B signal output
1 : MUT E signal output
0
R W
Rev. 1.0
110
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00ED16
CRT Clock Selection Register
b7 b6 b5 b4 b3 b2 b1 b0
0 0 0 0 0 0
CRT clock selection register (CK) [Address 00ED16]
B
Name
After reset R W
Functions
0, 1 CRT clock
Functions
b1 b0
selection bits 0 0 The clock for display is supplied by connecting RC
(CK0,CK1)
or LC across the pins OSC1 and OSC2.
0
1
1
0
R W
0
R W
1 Since the main clock is used as the
OSD oscillation
clock for display, the oscillation
frequency
frequency is limited. Because of this,
= f(XIN)
the character size in width (horizontal)
0
OSD oscillation
direction is also limited. In this case,
frequency
pins OSC1 and OSC2 are also used
= f(XIN)/1.5
as input ports P36 and P37 respectively.
1 The clock for OSD is supplied by connecting the
following across the pins OSC1 and OSC2.
• a ceramic resonator only for OSD and a feedback
resistor
• a quartz-crystal oscillator only for OSD and a
feedback resistor (See note)
2 to 7 Fix these bits to “0.”
Note: It is necessary to connect other ceramic resonator or quartz-crystal oscillator across the pins XIN and XOUT.
Addresses 00EE16
A-D Mode Register
b7 b6 b5 b4 b3 b2 b1 b0
A-D mode register (ADM) [Address 00EE16]
B
Name
Functions
0
to
2
Analog input pin selection
bits
(ADM0 to ADM2)
3
This bit is a write disable bit.
When this bit is read out, the value is “0.”
4
Storage bit of comparison
result (ADM4)
5
to
7
Nothing is assigned. This bits are write disable bits.
When these bits are read out, the values are “0.”
b2
0
0
0
0
1
1
1
1
b1
0
0
1
1
0
0
1
1
b0
0 : A-D1
1 : A-D2
0 : A-D3
1 : A-D4
0 : A-D5
1 : A-D6
0 : A-D7
1 : A-D8
0: Input voltage < reference voltage
1: Input voltage > reference voltage
After reset R W
0
R W
0
R —
Indeterminate
R —
0
R —
Rev. 1.0
111
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00EF16
A-D Control Register
b7 b6 b5 b4 b3 b2 b1 b0
A-D control register (ADC) [Address 00EF16]
B
Name
D-A converter set bits
(ADC0 to ADC5)
0
to
5
Functions
b5
0
0
0
b4
0
0
0
b3
0
0
0
b2
0
0
0
b1
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
0
1
1
After reset
R W
0
R W
0
R —
b0
0 : 1/128Vcc
1 : 3/128Vcc
0 : 5/128Vcc
1 : 123/128Vcc
0 : 125/128Vcc
1 : 127/128Vcc
6, 7 Nothing is assigned. These bits are write disable bits.
When these bits are reed out, the values are “ 0.”
Addresses 00F416
Timer 12 Mode Register
b7 b6 b5 b4 b3 b2 b1 b0
0
Timer mode register (T12M) [Address 00F416]
B
Name
Functions
After reset R W
0
Timer 1 count source 0: f(XIN)/16
selection bit 1 (T12M0) 1: f(XIN)/4096
0
R W
1
Timer 2 count source
selection bit (T12M1)
0: Interrupt clock source
1: External clock from TIM2 pin
0
R W
2 Timer 1 count
stop bit (T12M2)
0: Count start
1: Count stop
0
R W
3 Timer 2 count stop bit
(T12M3)
0: Count start
1: Count stop
0
R W
4 Timer 2 internal count
source selection bit 2
(T12M4)
0: f(XIN)/16
1: Timer 1 overflow
0
R W
0
R W
0
R —
5 Fix this bit to “0.”
6, 7 Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are “0.”
Rev. 1.0
112
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00F516
Timer 34 Mode Register
b7 b6 b5 b4 b3 b2 b1 b0
Timer 34 mode register (T34M) [Address 00F516]
B
Name
0 Timer 3 count source
selection bit (T34M0)
1
Functions
After reset R W
0
R W
0 : f(XIN)/16
1 : External clock source
0 : Timer 3 overflow signal
1 : f(XIN)/16
0
R W
2 Timer 3 count stop bit
(T34M2)
0: Count start
1: Count stop
0
R W
3 Timer 4 count stop bit
(T34M3)
0: Count start
1: Count stop
0
R W
4 Timer 4 count source
selection bit (T34M4)
0: Internal clock source
1: f(XIN)/2
0
R W
0
R W
0
R —
5
Timer 4 internal
interrupt count source
selection bit (T34M1)
Timer 3 external count 0: TIM3 pin input
source selection bit
1: HSYNC pin input
(T34M5)
6, 7 Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are “0.”
Addresses 00F916
Interrupt Input Polarity Register
b7 b6 b5 b4 b3 b2 b1 b0
0
0
Interrupt input polarity register(RE) [Address 00F916]
B
Name
Functions
0, 1 Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are “0.”
2
Fix this bit to “0.”
After reset
R W
0
R —
0
R W
3
INT1 polarity switch bit
(RE3)
0 : Positive polarity
1 : Negative polarity
0
R W
4
INT2 polarity switch bit
(R E 4)
0 : Positive polarity
1 : Negative polarity
0
R W
5
INT3 polarity switch bit
(R E 5)
0 : Positive polarity
1 : Negative polarity
0
R W
6
Nothing is assigned. This bit is a write disable bit.
When this bit is read out, the value is “0.”
0
R —
7
Fix this bit to “0.”
0
R W
Rev. 1.0
113
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00FB16
CPU Mode Register
b7 b6 b5 b4 b3 b2 b1 b0
1 1 1 1 1
0 0
CPU mode register (CM) [Address 00FB16]
B
Name
Functions
0, 1 Fix these bits to “0.”
Stack page selection
bit (CM2) (See note)
2
After reset R W
Indeterminate
R W
1
RW
Indeterminate
R W
0: 0 page
1: 1 page
3 to 7 Fix these bits to “1.”
Note: This bit is set to “1” after the reset release.
Addresses 00FC16
Interrupt Request Register 1
b7 b6 b5 b4 b3 b2 b1 b0
Interrupt request register 1 (IREQ1) [Address 00FC16]
B
Name
0 Timer 1 interrupt
request bit (TM1R)
R W
R ✽
1
R ✽
2
3
4
5
6
7
Functions
After reset
0
0 : No interrupt request issued
1 : Interrupt request issued
Timer 2 interrupt
0
0 : No interrupt request issued
request bit (TM2R) 1 : Interrupt request issued
0
Timer 3 interrupt
0 : No interrupt request issued
request bit (TM3R) 1 : Interrupt request issued
0
Timer 4 interrupt
0 : No interrupt request issued
request bit (TM4R) 1 : Interrupt request issued
OSD interrupt request 0 : No interrupt request issued
0
1 : Interrupt request issued
bit (OSDR)
VSYNC interrupt
0
0 : No interrupt request issued
request bit (VSCR) 1 : Interrupt request issued
0
Multi-master I2C-BUS interface 0 : No interrupt request issued
interrupt request bit (IICR)
1 : Interrupt request issued
0
0 : No interrupt request issued
INT3 external interrupt
request bit (IT3R)
1 : Interrupt request issued
R ✽
R ✽
R ✽
R ✽
R ✽
R ✽
✽: “0” can be set by software, but “1” cannot be set.
Rev. 1.0
114
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00FD16
Interrupt Request Register 2
b7 b6 b5 b4 b3 b2 b1 b0
0
Interrupt request register 2 (IREQ2) [Address 00FD16]
B
Name
0 INT1 external interrupt
Functions
After reset R W
0 : No interrupt request issued
1 : Interrupt request issued
0 : No interrupt request issued
1 : Interrupt request issued
0
R ✽
0
R ✽
0 : No interrupt request issued
1 : Interrupt request issued
3 Nothing is assigned. This bit is a write disable bit.
When this bit is read out, the value is “0.”
4 f(XIN)/4096 interrupt 0 : No interrupt request issued
request bit (MSR)
1 : Interrupt request issued
5, 6 Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are “0.”
7 Fix this bit to “0.”
0
R ✽
0
R —
0
R ✽
0
R —
0
R W
request bit (IT1R)
1
INT2 external interrupt
request bit (IT2R)
2
Serial I/O interrupt
request bit (S1R)
✽: “0” can be set by software, but “1” cannot be set.
Addresses 00FE16
Interrupt Control Register 1
b7 b6 b5 b4 b3 b2 b1 b0
Interrupt control register 1 (ICON1) [Address 00FE16]
B
Name
Functions
After reset R W
0 Timer 1 interrupt
enable bit (TM1E)
1 Timer 2 interrupt
enable bit (TM2E)
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
2 Timer 3 interrupt
enable bit (TM3E)
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
3 Timer 4 interrupt
enable bit (TM4E)
4 OSD interrupt enable bit
(OSDE)
5 VSYNC interrupt enable
bit (VSCE)
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
6 Multi-master I2C-BUS interface 0 : Interrupt disabled
interrupt enable bit (IICE)
1 : Interrupt enabled
0
R W
7 INT3 external interrupt
enable bit (IT3E)
0
R W
0 : Interrupt disabled
1 : Interrupt enabled
Rev. 1.0
115
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
Address 00FF16
Interrupt Control Register 2
b7 b6 b5 b4 b3 b2 b1 b0
0 0
0
Interrupt control register 2 (ICON2) [Address 00FF16]
B
Name
0 INT1 external interrupt
enable bit (IT1E)
1 INT2 external interrupt
enable bit (IT2E)
2 Serial I/O interrupt
enable bit (S1E)
3 Fix this bit to “0.”
4 f(XIN)/4096 interrupt
enable bit (MSE)
5, 6 Fix these bits to “0.”
7
Functions
After reset
R W
0 : Interrupt disabled
1 : Interrupt enabled
0 : Interrupt disabled
1 : Interrupt enabled
0 : Interrupt disabled
1 : Interrupt enabled
0
R W
0
R W
0
R W
0
R W
0
R W
0
R W
indeterminate
R –
0 : Interrupt disabled
1 : Interrupt enabled
Nothing is assigned. These bits are write disable bits. When
these bits are read out, the values are “indeterminate.”
Addresses 021B16
ROM Correction Enable Register
b7 b6 b5 b4 b3 b2 b1 b0
0 0
ROM correction enable register (RCR) [Address 021B16]
B
Name
Functions
0
Vector 1 enable bit (RC0)
0: Disabled
1: Enabled
0
R W
1
Vector 2 enable bit (RC1)
0: Disabled
1: Enabled
0
R W
0
R W
0
R —
2, 3 Fix these bits to “0.”
4
to
7
Nothing is assigned. These bits are write disable bits. When
these bits are read out, the values are “0.”
After reset R W
Rev. 1.0
116
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
21. PACKAGE OUTLINE
52P4B
Plastic 52pin 600mil SDIP
EIAJ Package Code
SDIP52-P-600-1.78
Weight(g)
5.1
Lead Material
Alloy 42/Cu Alloy
27
1
26
E
52
e1
c
JEDEC Code
–
Symbol
A
A1
A2
b
b1
b2
c
D
E
e
e1
L
L
A1
A
A2
D
e
b1
b
b2
SEATING PLANE
80P6N-A
Dimension in Millimeters
Min
Nom
Max
–
–
5.5
0.51
–
–
–
3.8
–
0.4
0.5
0.6
0.9
1.0
1.3
0.65
0.75
1.05
0.22
0.27
0.34
45.65
45.85
46.05
12.85
13.0
13.15
–
1.778
–
–
15.24
–
3.0
–
–
0°
–
15°
Plastic 80pin 14✕20mm body QFP
EIAJ Package Code
QFP80-P-1420-0.80
Weight(g)
1.58
Lead Material
Alloy 42
MD
e
JEDEC Code
–
HD
D
b2
1
ME
65
80
64
I2
E
24
HE
Recommended Mount Pad
Symbol
41
A
40
25
e
y
b
F
A1
c
A2
L1
L
Detail F
A
A1
A2
b
c
D
E
e
HD
HE
L
L1
y
b2
I2
MD
ME
Dimension in Millimeters
Min
Nom
Max
3.05
–
–
0.1
0.2
0
2.8
–
–
0.3
0.35
0.45
0.13
0.15
0.2
13.8
14.0
14.2
19.8
20.0
20.2
0.8
–
–
16.5
16.8
17.1
22.5
22.8
23.1
0.4
0.6
0.8
1.4
–
–
0.1
–
–
0°
10°
–
0.5
–
–
–
–
1.3
14.6
–
–
20.6
–
–
Rev. 1.0
117
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
HEAD OFFICE: 2-2-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
Keep safety first in your circuit designs!
•
Mitsubishi Electric Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to
personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of non-flammable
material or (iii) prevention against any malfunction or mishap.
•
These materials are intended as a reference to assist our customers in the selection of the Mitsubishi semiconductor product best suited to the customer’s application; they do not convey any license under any intellectual property
rights, or any other rights, belonging to Mitsubishi Electric Corporation or a third party.
Mitsubishi Electric Corporation assumes no responsibility for any damage, or infringement of any third-party’s rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples
contained in these materials.
All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by
Mitsubishi Electric Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product
distributor for the latest product information before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors. Mitsubishi Electric Corporation assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors.
Please also pay attention to information published by Mitsubishi Electric Corporation by various means, including the Mitsubishi Semiconductor home page (http://www.mitsubishichips.com).
When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision
on the applicability of the information and products. Mitsubishi Electric Corporation assumes no responsibility for any damage, liability or other loss resulting from the information contained herein.
Mitsubishi Electric Corporation semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Mitsubishi Electric
Corporation or an authorized Mitsubishi Semiconductor product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical,
aerospace, nuclear, or undersea repeater use.
The prior written approval of Mitsubishi Electric Corporation is necessary to reprint or reproduce in whole or in part these materials.
If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved
destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for further details on these materials or the products contained therein.
Notes regarding these materials
•
•
•
•
•
•
•
© 1999 MITSUBISHI ELECTRIC CORP.
New publication, effective Sep. 1999.
Specifications subject to change without notice.
MITSUBISHI MICROCOMPUTERS
M37212M4/M8–XXXSP, M37212M6–XXXSP/FP
M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
REVISION HISTORY
Rev.
No.
1.0
M37212M4/M8-XXXSP, M37212M6-XXXSP/FP,
M37212EFSP/FP (Rev.1.0)
DATA SHEET
Revision Description
PDF First Edition
Rev.
date
9909
Rev. 1.0
(1/1)
119
Similar pages