Coilcraft MS590PND273MSZ High reliability coupled inductor Datasheet

1260 COUPLED INDUCTORS
High Reliability Coupled Inductors MS590PND
The MS590PND series of shielded coupled inductors was
designed specifically for high temperature applications –
up to 155°C. Tin-lead (Sn-Pb) terminations are used for
the best possible board adhesion.
The excellent coupling coefficient (k ≥ 0.98) makes it ideal
for use in SEPIC applications. In SEPIC topologies, the
required inductance for each winding in a coupled inductor is half the value needed for two separate inductors,
allowing selection of a part with lower DCR and higher
current handling.
These inductors provide high inductance, high efficiency,
excellent current handling and 500 V isolation in a very
rugged part. They are well suited for use as VRM inductors in high-current DC-DC and VRM/VRD controllers.
They can also be used as two single inductors connected
in series or parallel, as a common mode choke or as a
1 : 1 transformer.
0.484
max
12,3
0.484
max
12,3
123
X
D1
+
L1
Dot indicates pin1
VIN
Dash number
Internal code
+
C1
L2
Q1
C2
+
Load
–
VOUT
–
Typical SEPIC schematic
Refer to Application Note, Document 639,
“Selecting Coupled Inductors for SEPIC Applications”
0.236 ±0.008 *
6,0 ±0,2
Suggested
Land Pattern
0.217
5,5
0.197
5,0
0.138
3,5
0.197
5,0
0.157
4,0
3
4
2
1
2
1
3
4
0.059
1,5
0.177
4,5
0.079
2,0
* Dimensions are for the mounted part.
Dimensions before mounting can be
an additional 0.006 inch (0,152 mm).
1
L1
inches
Dimensions are in
mm
3
®
2
L2
4
Specifications subject to change without notice.
Please check our website for latest information.
1102 Silver Lake Road
Cary IL 60013
© Coilcraft, Inc. 2012
Core material Ferrite
Terminations Tin-lead (63/37) over tin over nickel over phos bronze
Weight: 2.8 – 3.2 g
Ambient temperature –55°C to +105°C with Irms current, +105°C
to +155°C with derated current
Storage temperature Component: –55C to +155°C.
Tape and reel packaging: –55°C to +80°C
Winding to winding isolation 500 Vrms
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Winding-to-winding and winding-to-core isolation 500 Vrms
Enhanced crush-resistant packaging 500/13″ reel;
Plastic tape: 24 mm wide, 0.35 mm thick, 16 mm pocket spacing,
6.6 mm pocket depth
Document MS703-1
Phone 800-981-0363
Fax 847-639-1508
Revised 07/13/12
E-mail [email protected]
Web www.coilcraft-cps.com
1260 COUPLED INDUCTORS
MS590PND Series (1260)
SRF (MHz)4
Inductance2 DCR max3 Part number1
(µH)
(Ohms)
min typ
MS590PND472MSZ
4.7 ±20%
0.036
30.0
38.0
MS590PND562MSZ
5.6 ±20%
0.040
24.0
30.0
MS590PND682MSZ
6.8 ±20%
0.048
22.0
27.0
MS590PND822MSZ
8.2 ±20%
0.052
21.0
26.0
MS590PND103MSZ
10 ±20%
0.060
18.0
22.0
Coupling Leakage Isat (A)5 Irms (A)
coefficient L typ
10%
20%
30%
both
one
typ
(µH)
drop drop drop
windings6 winding7
0.98
0.20
9.00 10.18 11.08
3.16
4.47
0.98
0.20
8.00
9.06
9.84
3.00
4.24
0.98
0.24
7.00
8.00
8.64
2.75
3.88
0.98
0.25
6.44
7.38
7.98
2.63
3.72
0.99
0.26
5.40
6.32
6.88
2.45
3.46
MS590PND123MSZ
MS590PND153MSZ
MS590PND183MSZ
MS590PND223MSZ
MS590PND273MSZ
12
15
18
22
27
±20%
±20%
±20%
±20%
±20%
0.074
0.085
0.097
0.116
0.124
16.0
14.4
13.0
12.0
10.0
20.0
18.0
16.0
15.0
13.0
0.99
0.99
0.99
0.98
0.99
0.28
0.32
0.40
0.67
0.50
5.30
4.60
4.50
4.00
3.60
6.18
5.30
5.22
4.62
4.14
6.70
5.80
5.68
5.02
4.50
2.21
2.06
1.93
1.76
1.70
3.12
2.92
2.73
2.49
2.41
MS590PND333MSZ
MS590PND393MSZ
MS590PND473MSZ
MS590PND563MSZ
MS590PND683MSZ
33
39
47
56
68
±20%
±20%
±20%
±20%
±20%
0.134
0.142
0.174
0.198
0.216
10.0
9.6
9.3
8.4
8.0
12.4
12.0
11.6
10.5
10.0
0.99
0.99
0.99
0.99
>0.99
0.65
1.09
0.80
0.75
0.57
3.30
3.00
2.70
2.50
2.30
3.80
3.48
3.12
2.90
2.66
4.14
3.82
3.40
3.14
2.88
1.64
1.59
1.44
1.35
1.29
2.32
2.25
2.03
1.91
1.83
MS590PND823MSZ
MS590PND104MSZ
MS590PND124KSZ
MS590PND154KSZ
MS590PND184KSZ
82
100
120
150
180
±20%
±20%
±10%
±10%
±10%
0.274
0.322
0.418
0.476
0.536
6.9
6.2
5.5
5.1
4.9
8.6
7.8
6.8
6.4
6.1
0.99
0.99
0.99
0.99
0.99
1.52
1.41
1.34
1.52
1.80
2.10
1.90
1.60
1.50
1.40
2.40
2.18
1.84
1.76
1.64
2.60
2.38
2.04
1.92
1.78
1.15
1.06
0.93
0.87
0.82
1.62
1.50
1.31
1.23
1.16
MS590PND224KSZ
MS590PND274KSZ
MS590PND334KSZ
MS590PND394KSZ
MS590PND474KSZ
220
270
330
390
470
±10%
±10%
±10%
±10%
±10%
0.691
0.806
1.09
1.20
1.59
4.4
3.4
3.2
2.9
2.4
5.5
4.3
4.0
3.6
3.0
>0.99
>0.99
>0.99
>0.99
>0.99
1.60
2.23
2.39
3.72
2.89
1.30
1.10
1.00
0.950
0.900
1.48
1.30
1.16
1.11
0.994
1.60
1.40
1.26
1.23
1.09
0.72
0.67
0.57
0.55
0.48
1.02
0.95
0.81
0.77
0.67
MS590PND564KSZ
MS590PND684KSZ
MS590PND824KSZ
MS590PND105KSZ
560
680
820
1000
±10%
±10%
±10%
±10%
1.81
2.06
2.65
3.06
2.2
2.1
2.0
1.9
2.8
2.6
2.5
2.4
>0.99
>0.99
>0.99
>0.99
2.55
5.76
2.86
4.32
0.800
0.700
0.640
0.590
0.908
0.804
0.732
0.674
0.948
0.874
0.802
0.728
0.45
0.42
0.37
0.34
0.63
0.59
0.52
0.49
Temperature rise calculation based on specified Irms
1. When ordering, please specify testing code:
MS590PND105KSZ
Testing: Z = COTS
H = Screening per Coilcraft CP-SA-10001
N = Screening per Coilcraft CP-SA-10004
2. Inductance shown for each winding, measured at 100 kHz, 0.1 Vrms,
0 Adc on an Agilent/HP 4284A LCR meter or equivalent. When leads
are connected in parallel, inductance is the same value. When leads
are connected in series, inductance is four times the value.
3. DCR is for each winding. When leads are connected in parallel, DCR
is half the value. When leads are connected in series, DCR is twice the
value.
4. SRF measured using an Agilent/HP 4191A or equivalent. When leads
are connected in parallel, SRF is the same value.
5. DC current, at which the inductance drops the specified amount from
its value without current. It is the sum of the current flowing in both
windings.
6. Equal current when applied to each winding simultaneously that
causes a 40°C temperature rise from 25°C ambient. See temperature
rise calculation.
7. Maximum current when applied to one winding that causes a 40°C
temperature rise from 25°C ambient. See temperature rise calculation.
8. Electrical specifications at 25°C.
Refer to Doc 639 “Selecting Coupled Inductors for SEPIC Applications.”
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
®
Specifications subject to change without notice.
Please check our website for latest information.
1102 Silver Lake Road
Cary IL 60013
© Coilcraft, Inc. 2012
Document MS703-1
Phone 800-981-0363
Fax 847-639-1508
Revised 07/13/12
E-mail [email protected]
Web www.coilcraft-cps.com
1260 COUPLED INDUCTORS
MS590PND Series (1260)
Typical L vs Current
Typical L vs Frequency
10000
10000
1000 µH
470 µH
100 µH
100
1000 µH
1000
Inductance (µH)
Inductance (µH)
1000
47 µH
10 µH
10
470 µH
100 µH
100
47 µH
10 µH
10
4.7 µH
4.7 µH
1
0.1
1
10
100
Current (A)
1
0.01
0.1
1
10
Frequency (MHz)
Current Derating
120
100
90
80
70
60
50
40
25°C
Percent of rated Current
110
30
20
10
0
-55 -40
Isat
Irms
-20
0
20
40
60
80
100
120
140 160
Ambient temperature (°C)
®
Specifications subject to change without notice.
Please check our website for latest information.
1102 Silver Lake Road
Cary IL 60013
© Coilcraft, Inc. 2012
Document MS703-1
Phone 800-981-0363
Fax 847-639-1508
Revised 07/13/12
E-mail [email protected]
Web www.coilcraft-cps.com
Similar pages