STMicroelectronics ESDA7P60-1U1M High power transient voltage suppressor Datasheet

ESDA7P60-1U1M
High power transient voltage suppressor
Datasheet - production data
Description
The ESDA7P60-1U1M is a unidirectional single
line TVS diode designed to protect the power line
against EOS and ESD transients.
3LQ
The device is ideal for applications where high
power TVS and board space saving are required.
3LQ
Figure 1. Pin configuration
3LQ
3LQ
SDFNDJH
Features
• Low clamping voltage
• Typical peak pulse power:
– 700 W (8/20µs)
• Stand off voltage 5 V
• Unidirectional diode
• Low leakage current:
– 0.2 µA at 25 °C
• RoHS compliant
Complies with the following standards:
• IEC 61000-4-2 level 4
– ±30 kV (air discharge)
– ±30 kV (contact discharge)
Applications
Where transient overvoltage protection in ESD
sensitive equipment is required, such as:
• Portable multimedia, tablets, mobile phone,
smart phone
• USB VBUS protection
• Power supply protection
• Battery protection
October 2015
This is information on a product in full production.
DocID027044 Rev 3
1/10
www.st.com
Characteristics
1
ESDA7P60-1U1M
Characteristics
Table 1. Absolute maximum ratings (Tamb = 25 °C)
Symbol
Parameter
Value
Unit
> 30
> 30
kV
VPP
Peak pulse voltage:
IEC 61000-4-2 contact discharge
EC 61000-4-2 air discharge
PPP
Peak pulse current (8/20 µs)
700
W
IPP
Peak pulse current (8/20 µs)
60
A
Tstg
Storage temperature range
- 55 to +150
°C
Top
Operating junction temperature range
-55 to +150
°C
Figure 2. Electrical characteristics (definitions)
,
,)
9)
9&/ 9 %5 950
9
, 50
,5
6ORSH
5 G
, 33
Table 2. Electrical characteristics (values, Tamb = 25 °C)
Symbol
2/10
Test conditions
Min.
Typ.
Max.
Unit
6.4
6.8
7.2
V
200
nA
11.6
V
VBR
IR = 1 mA
IRM
VRM = 5 V
VCL
IPP = 60 A 8/20 µs
10.2
Rd
8/20 µs
0.06
DocID027044 Rev 3
Ω
ESDA7P60-1U1M
Characteristics
Figure 3. Peak pulse power dissipation versus Figure 4. Peak pulse power versus exponential
initial junction temperature (typical values)
pulse duration (maximum values)
333 : 333 : —V
7\SLFDOYDOXH
7MLQLWLDO ƒ&
7\SLFDOYDOXHV
7M ƒ&
Figure 5. Peak pulse current versus clamping
voltage (maximum values)
,
:
33
WS —V
Figure 6. Leakage current versus junction
temperature (typical values)
, Q$ 5
95 950 9
—V
7MLQLWLDO ƒ&
9&/ 9
Figure 7. ESD response to IEC 61000-4-2
(+8 kV contact discharge)
9GLY
7 ƒ&
M
Figure 8. ESD response to IEC 61000-4-2
(-8 kV contact discharge)
9GLY
9 33 (6'SHDNYROWDJH
9 &/&ODPSLQJYROWDJH#QV
9 &/&ODPSLQJYROWDJH#QV
9 &/&ODPSLQJYROWDJH#QV
9
9
9 9
9
P9 9
9 QVGLY
DocID027044 Rev 3
9 33 (6'SHDNYROWDJH
9 &/&ODPSLQJYROWDJH#QV
9 &/&ODPSLQJYROWDJH#QV
9 &/&ODPSLQJYROWDJH#QV
QVGLY
3/10
10
Package information
2
ESDA7P60-1U1M
Package information
•
Epoxy meets UL94, V0
•
Dot indicates pin 1
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
2.1
1610 package information
Figure 9. 1610 package outline
(
'
$
7RSYLHZ
$
6LGH YLHZ
E
H
/
%RWWRP YLHZ
Table 3. 1610 package mechanical data
Dimensions
Ref.
A
Millimeters
Min.
Typ.
Max.
Min.
Typ.
Max.
0.51
0.55
0.60
0.020
0.021
0.023
A1
0.00
0.02
0.05
b
0.75
0.80
0.85
0.029
0.031
0.033
D
1.50
1.60
1.70
0.059
0.063
0.067
E
0.90
1.00
1.10
0.035
0.039
0.043
0.30
0.35
0.40
0.011
0.013
e
L
4/10
Inches
0.002
1.05
0.041
DocID027044 Rev 3
0.016
ESDA7P60-1U1M
Package information
PP
Figure 11. Alternative footprint, dimensions in
mm
PP
PP
PP
PP
PP
PP
PP
PP
Figure 10. Footprint, dimensions in mm
PP
Figure 12. Marking
3LQ
Note:
)
3LQ
Product marking may be rotated by multiples of 90° for assembly plant differentiation. In no
case should this product marking be used to orient the component for its placement on a
PCB. Only pin 1 mark is to be used for this purpose.
DocID027044 Rev 3
5/10
10
Package information
2.2
ESDA7P60-1U1M
Packing information
Figure 13. Tape and reel outline
“
‘
“
“
%DULQGLFDWHV3LQ
“
“
“
$OOGLPHQVLRQVDUHW\SLFDOYDOXHVLQPP
8VHUGLUHFWLRQRIXQUHHOLQJ
6/10
DocID027044 Rev 3
)
)
)
)
)
)
)
“
“
“
“
ESDA7P60-1U1M
Recommendation on PCB assembly
3
Recommendation on PCB assembly
3.1
Stencil opening design
1.
General recommendation on stencil opening design
a)
Stencil opening dimensions: L (Length), W (Width), T (Thickness).
Figure 14. Stencil opening dimensions
/
7
b)
:
General design rule
Stencil thickness (T) = 75 ~ 125 µm
W
Aspect Ratio = ----- ≥ 1.5
T
L×W
Aspect Area = ---------------------------- ≥ 0.66
2T ( L + W )
Reference design
a)
Stencil opening thickness: 100 µm
b)
Stencil opening for leads: Opening to footprint ratio is 90%.
Figure 15. Recommended stencil window
position
PP
PP
PP
PP
PP
PP
PP
PP
Figure 16. Alternative stencil window position
PP
PP
PP
6WHQFLOZLQGRZ
PP
PP
2.
PP
)RRWSULQW
6WHQFLOZLQGRZ
DocID027044 Rev 3
)RRWSULQW
7/10
10
Recommendation on PCB assembly
3.2
3.3
3.4
3.5
ESDA7P60-1U1M
Solder paste
1.
Use halide-free flux, qualification ROL0 according to ANSI/J-STD-004.
2.
“No clean” solder paste recommended.
3.
Offers a high tack force to resist component displacement during PCB movement.
4.
Use solder paste with fine particles: powder particle size 20-45 µm.
Placement
1.
Manual positioning is not recommended.
2.
It is recommended to use the lead recognition capabilities of the placement system, not
the outline centering.
3.
Standard tolerance of ± 0.05 mm is recommended.
4.
3.5 N placement force is recommended. Too much placement force can lead to
squeezed out solder paste and cause solder joints to short. Too low placement force
can lead to insufficient contact between package and solder paste that could cause
open solder joints or badly centered packages.
5.
To improve the package placement accuracy, a bottom side optical control should be
performed with a high resolution tool.
6.
For assembly, a perfect supporting of the PCB (all the more on flexible PCB) is
recommended during solder paste printing, pick and place and reflow soldering by
using optimized tools.
PCB design preference
1.
To control the solder paste amount, the closed via is recommended instead of open
vias.
2.
The position of tracks and open vias in the solder area should be well balanced. The
symmetrical layout is recommended, in case any tilt phenomena caused by
asymmetrical solder paste amount due to the solder flow away.
Reflow profile
Figure 17. ST ECOPACK® recommended soldering reflow profile for PCB mounting
ƒ&
7HPSHUDWXUH ƒ&
ƒ&V
ƒ&V
VHF
PD[
ƒ&V
ƒ&V
ƒ&V
7LPH V
Note:
8/10
Minimize air convection currents in the reflow oven to avoid component movement.
DocID027044 Rev 3
ESDA7P60-1U1M
4
Ordering information
Ordering information
Figure 18. Ordering information scheme
(6'$ 380
(6' $UUD\
%UHDNGRZQYROWDJH
9W\S
,33—V
3 $
'LUHFWLRQ
8 8QLGLUHFWLRQDO
3DFNDJH
0 4)1
Table 4. Ordering information
Order code
Marking
Weight
Base qty
Delivery mode
ESDA7P60
F(1)
2.4 mg
8000
Tape and reel
1. The marking can be rotated by multiples of 90° to differentiate assembly location
5
Revision history
Table 5. Document revision history
Date
Revision
Changes
14-Nov-2014
1
Initial release.
02-Jul-2015
2
Updated Figure 4.
14-Oct-2015
2
Updated Description and reformatted to current standard.
DocID027044 Rev 3
9/10
10
ESDA7P60-1U1M
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2015 STMicroelectronics – All rights reserved
10/10
DocID027044 Rev 3
Similar pages