Infineon ICB2FL03G 2nd generation fl controller for fluorescent lamp ballast Datasheet

ICB2FL03G
2nd Generation FL Controller for
Fluorescent Lamp Ballasts
Data Sheet
V1.1, 2013-08-14
Final
Power Management & Multimarket
Edition 2013-08-14
Published by
Infineon Technologies AG
81726 Munich, Germany
© 2013 Infineon Technologies AG
All Rights Reserved.
Legal Disclaimer
The information given in this document shall in no event be regarded as a guarantee of conditions or
characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any
information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties
and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights
of any third party.
Information
For further information on technology, delivery terms and conditions and prices, please contact the nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements, components may contain dangerous substances. For information on the types in
question, please contact the nearest Infineon Technologies Office.
Infineon Technologies components may be used in life-support devices or systems only with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Revision History
Page or Item
Subjects (major changes since previous revision)
Final V1.1, 2013-08-14
page 54-55
inserted Chapter 5.3.4 Parameter limits for extended temperature range down to -40°C
Final V1.0 2013-02-14
page 45
changed max value for IHSVCCqu1 from 270µA to 280µA
changed min value for VHSVCCOn from 9.9V to 9.8V
page 48
changed min value for VPFCGDRise from 105ns to 100ns
typo correction: VPFCGDRise & VPFCGDFall --> tPFCGDRise & tPFCGDFall
page 50
changed min value for tLSGDRisefrom 105ns to 100ns
page 52
changed min value for THSGDRise from 140ns to 120ns
typo correction: THSGDRise & THSGDFall --> tHSGDRise & tHSGDFall
Trademarks of Infineon Technologies AG
AURIX™, C166™, CanPAK™, CIPOS™, CIPURSE™, EconoPACK™, CoolMOS™, CoolSET™,
CORECONTROL™, CROSSAVE™, DAVE™, DI-POL™, EasyPIM™, EconoBRIDGE™, EconoDUAL™,
EconoPIM™, EconoPACK™, EiceDRIVER™, eupec™, FCOS™, HITFET™, HybridPACK™, I²RF™,
ISOFACE™, IsoPACK™, MIPAQ™, ModSTACK™, my-d™, NovalithIC™, OptiMOS™, ORIGA™,
POWERCODE™; PRIMARION™, PrimePACK™, PrimeSTACK™, PRO-SIL™, PROFET™, RASIC™,
ReverSave™, SatRIC™, SIEGET™, SINDRION™, SIPMOS™, SmartLEWIS™, SOLID FLASH™, TEMPFET™,
thinQ!™, TRENCHSTOP™, TriCore™.
Other Trademarks
Advance Design System™ (ADS) of Agilent Technologies, AMBA™, ARM™, MULTI-ICE™, KEIL™,
PRIMECELL™, REALVIEW™, THUMB™, µVision™ of ARM Limited, UK. AUTOSAR™ is licensed by AUTOSAR
development partnership. Bluetooth™ of Bluetooth SIG Inc. CAT-iq™ of DECT Forum. COLOSSUS™,
FirstGPS™ of Trimble Navigation Ltd. EMV™ of EMVCo, LLC (Visa Holdings Inc.). EPCOS™ of Epcos AG.
FLEXGO™ of Microsoft Corporation. FlexRay™ is licensed by FlexRay Consortium. HYPERTERMINAL™ of
Hilgraeve Incorporated. IEC™ of Commission Electrotechnique Internationale. IrDA™ of Infrared Data
Association Corporation. ISO™ of INTERNATIONAL ORGANIZATION FOR STANDARDIZATION. MATLAB™ of
MathWorks, Inc. MAXIM™ of Maxim Integrated Products, Inc. MICROTEC™, NUCLEUS™ of Mentor Graphics
Corporation. MIPI™ of MIPI Alliance, Inc. MIPS™ of MIPS Technologies, Inc., USA. muRata™ of MURATA
MANUFACTURING CO., MICROWAVE OFFICE™ (MWO) of Applied Wave Research Inc., OmniVision™ of
OmniVision Technologies, Inc. Openwave™ Openwave Systems Inc. RED HAT™ Red Hat, Inc. RFMD™ RF
Micro Devices, Inc. SIRIUS™ of Sirius Satellite Radio Inc. SOLARIS™ of Sun Microsystems, Inc. SPANSION™
of Spansion LLC Ltd. Symbian™ of Symbian Software Limited. TAIYO YUDEN™ of Taiyo Yuden Co.
TEAKLITE™ of CEVA, Inc. TEKTRONIX™ of Tektronix Inc. TOKO™ of TOKO KABUSHIKI KAISHA TA. UNIX™
of X/Open Company Limited. VERILOG™, PALLADIUM™ of Cadence Design Systems, Inc. VLYNQ™ of Texas
Instruments Incorporated. VXWORKS™, WIND RIVER™ of WIND RIVER SYSTEMS, INC. ZETEX™ of Diodes
Zetex Limited.
Last Trademarks Update 2011-11-11
Final Data Sheet
3
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Table of Contents
Table of Contents
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2nd Generation FL-Controller for Fluorescent Lamp Ballasts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1
1.1
1.2
1.3
Pin Configuration and Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
PG-DSO-16 Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Pin Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2
2.1
2.2
2.2.1
2.2.2
2.3
2.3.1
2.3.2
2.3.3
2.4
2.4.1
2.4.2
2.4.2.1
2.4.2.2
2.4.3
2.4.4
2.5
2.5.1
2.5.2
2.6
2.6.1
2.6.2
2.6.3
2.7
2.7.1
2.7.2
2.8
2.8.1
2.8.1.1
2.8.1.2
2.8.2
2.8.3
2.8.3.1
2.8.3.2
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical Application Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Levels from UVLO to Soft Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Levels from Soft Start to Run Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Filament Detection during Start-Up and Run Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Start-Up with broken Low Side Filament . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low Side Filament Detection during Run Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Start-Up with Broken High Side Filament . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PFC Preconverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Discontinuous Conduction and Critical Conduction Mode Operation . . . . . . . . . . . . . . . . . . . . . . .
PFC Bus Voltage Sensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bus Overvoltage and PFC Open Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bus Voltage 95 % and 75 % Sensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PFC Structure of Mixed Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
THD Correction via ZCD Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Detection of End-of-Life and Rectifier Effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Detection of End of Life 1 (EOL1) – Lamp Overvoltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Detection of End of Life 2 (EOL2) – Rectifier Effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Detection of Capacitive Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Capacitive Load 1 (Idling Detection – Current Mode Preheating) . . . . . . . . . . . . . . . . . . . . . . . . . .
Capacitive Load 2 (Overcurrent / Operation below Resonance) . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjustable Self-adapting Dead Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Emergency Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Short-term PFC Bus Undervoltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Long-term PFC Bus Undervoltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Built-in Customer Test Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preheating Test Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Skip the Preheating Phase – Set RTPH Pin to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IC Remains in Preheating Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deactivation of the Filament Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Built-in Customer Test Mode (Clock Acceleration) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enabling of the Clock Acceleration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting the Chip with Accelerated Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
14
14
16
17
19
19
20
21
23
23
23
24
24
25
25
26
27
28
28
29
30
30
31
31
32
32
32
33
34
35
36
36
36
3
3.1
3.2
3.3
State Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features during Different Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Flow of the Start-Up Procedure into Run Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Restart and Latched Fault Condition Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
37
37
38
39
Final Data Sheet
4
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Table of Contents
4
Protection Functions Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
5
5.1
5.2
5.3
5.3.1
5.3.2
5.3.2.1
5.3.2.2
5.3.2.3
5.3.2.4
5.3.2.5
5.3.3
5.3.3.1
5.3.3.2
5.3.3.3
5.3.3.4
5.3.3.5
5.3.3.6
5.3.3.7
5.3.3.8
5.3.3.9
5.3.4
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PFC Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PFC Current Sense (PFCCS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PFC Zero Current Detection (PFCZCD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PFC Bus Voltage Sense (PFCVS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PFC PWM Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PFC gate Drive (PFCGD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inverter Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low Side Current Sense (LSCS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low Side Gate Drive (LSGD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inverter Control Run (RFRUN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inverter Control Preheating (RFPH, RTPH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restart after Lamp Removal (RES) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lamp Voltage Sense (LVS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Side Gate Drive (HSGD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Built-In Customer Test Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parameter limits for extended temperature range down to -40°C . . . . . . . . . . . . . . . . . . . . . . . . . .
42
42
44
45
45
46
46
46
47
47
48
49
49
50
50
51
51
52
52
53
53
54
6
6.1
6.2
6.3
Application Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Schematic Ballast 54W T5 Single Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bill of Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multi Lamp Ballast Topologies (Series Connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
56
56
57
58
7
7.1
Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Outline Dimensions of PG-DSO-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Final Data Sheet
5
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
List of Figures
List of Figures
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13
Figure 14
Figure 15
Figure 16
Figure 17
Figure 18
Figure 19
Figure 20
Figure 21
Figure 22
Figure 23
Figure 24
Figure 25
Figure 26
Figure 27
Figure 28
Figure 29
Figure 30
Figure 31
Figure 32
Figure 33
Figure 34
Figure 35
Figure 36
Figure 37
Figure 38
Figure 39
Figure 40
Typical Application Circuit of Ballast for a Single Fluorescent Lamp . . . . . . . . . . . . . . . . . . . . . . . . 8
PG-DSO-16 Package (top view). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Application Circuit of Ballast for a Single Fluorescent Lamp (FL). . . . . . . . . . . . . . . . . . . . . . . . . . 14
Typical Startup Procedure in Run Mode (in Normal Operation) . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Typical Startup Procedure in Run Mode (in Normal Operation) . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Typical Variation of Operating Frequency during Startup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Lamp Voltage versus Frequency during the different Startup Phases . . . . . . . . . . . . . . . . . . . . . . 18
Start-Up with Open Low Side Filament. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Restart from Open Low Side Filament . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Open Low Side Filament Run Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Restart from Open LS Filament . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Start-Up with Open High Side Filament . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Restart from Open High Side Filament. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Operating Frequency and ON Time versus Power in DCM and CritCM Operation . . . . . . . . . . . . 23
PFC Bus Voltage Operating Level and Error Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Structure of the Mixed Digital and Analog Control of the PFC Preconverter . . . . . . . . . . . . . . . . . 25
THD Optimization using adjustable Pulse Width Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
End of Life and Rectifier Effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
End of Life (EOL1) Detection, Lamp Voltage versus AC LVS Current . . . . . . . . . . . . . . . . . . . . . . 27
End of Life (EOL2) Detection, Lamp Voltage versus DC LVS Current . . . . . . . . . . . . . . . . . . . . . . 28
Capacitive and Inductive Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Capacitive Mode 1 Operation without Load during Run Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Capacitive Mode 2 – Operation with Overcurrent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Dead Time of ON and OFF of the Half-Bridge Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
BUS Voltage Drop below 75% (rated Bus Voltage) for t < 800 ms during RUN Mode . . . . . . . . . . 31
BUS Voltage Drop below 75% (rated Bus Voltage) for t > 800 ms during RUN Mode . . . . . . . . . . 32
Start-Up WITH Preheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Start-Up WITHOUT Preheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Start-Up WITH Preheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Start-Up WITHOUT Preheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Deactivation via RES PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Deactivation via LVS PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Clock Acceleration (Built in Customer Test Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Monitoring Features during Different Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Operating Flow during Start-Up Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Operating Process during Start-Up Mode and Handling of Fault Conditions . . . . . . . . . . . . . . . . . 39
Application Circuit of Ballast for Single Fluorescent Lamp Voltage Mode Preheating . . . . . . . . . . 56
Bill of Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Application Circuit of Ballast for two Fluorescent Lamps Voltage Mode Preheating . . . . . . . . . . . 58
Package Outline with Creepage Distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Final Data Sheet
6
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
List of Tables
List of Tables
Table 1
Table 2
Table 3
Pin Configuration for PG-DSO-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Specified Acceleration Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Protection Functions Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Final Data Sheet
7
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
2nd Generation FL-Controller for Fluorescent Lamp Ballasts
Product Highlights
•
•
•
•
•
•
•
•
Lowest count of external components
650 V half-bridge driver with coreless transformer technology
Supports Customer In-Circuit Test Mode for reduced tester time
Supports multi-lamp designs (series connection)
Integrated digital timers up to 40 seconds
Numerous monitoring and protection features for highest reliability
Very high accuracy of frequencies and timers over the whole temperature range
Very low standby losses
PFC Features
•
•
•
•
Discontinuous mode PFC for load range 0 to 100%
Integrated digital compensation of PFC control loop
Improved compensation for low THD of AC input current, also in DCM operation
Adjustable PFC current limitation
Lamp Ballast Inverter Features
•
•
•
•
•
•
Adjustable detection of overload and rectifier effect (EOL)
Detection of capacitive load operation
Improved ignition control allows operation close to the magnetic saturation of the lamp inductors
Restart with skipped preheating on short interruptions of line voltage (for emergency lighting)
Parameters adjustable by resistors only
Pb-free lead plating; RoHS-compliant
LVS
PFCZCD
Figure 1
LSGD
LSCS
RFPH
RFRUN
VCC
GND
PFCCS
HSGND
RES
PFCVS
RTPH
PFCGD
VIN
ICB2FL03G
HSGD
HSVCC
Typical Application Circuit of Ballast for a Single Fluorescent Lamp
Description
The FL controller ICB2FL03G is designed to control fluorescent lamp ballast, including a discontinuous mode
Power Factor Correction (PFC), lamp inverter control and a high-voltage level shift half-bridge driver.
The control concept covers requirements for T5 lamp ballasts for single and multi-lamp designs (series connection
supported). ICB2FL03G is based on the 2nd-generation FL controller technology, is easy to use and simple to
design in. This makes the ICB2FL03G a basis for cost-effective solutions for fluorescent lamp ballasts with high
reliability. Figure 1 shows a typical application circuit of ballast for a single fluorescent T8 lamp with current mode
preheating.
Final Data Sheet
8
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Pin Configuration and Functionality
1
Pin Configuration and Functionality
1.1
Pin Configuration
Table 1
Pin Configuration for PG-DSO-16
Pin
Symbol
Function
1
LSGD
Low side gate drive (inverter)
2
LSCS
Low side current sense (inverter)
3
VCC
Supply voltage
4
GND
Low side ground
5
PFCGD
PFC gate drive
6
PFCCS
PFC current sense
7
PFCZCD
PFC zero current detector
8
PFCVS
PFC voltage sense
9
RFRUN
Set R for run frequency
10
RFPH
Set R for preheat frequency
11
RTPH
Set R for preheating time
12
LVS
Lamp voltage sense
13
RES
Restart after lamp removal
14
HSGND
High side ground
15
HSVCC
High side supply voltage
16
HSGD
High side gate drive (inverter)
PG-DSO-16 Package
LSGD
1
16
HSGD
LSCS
2
15
HSVCC
VCC
3
14
HSGND
GND
4
13
RES
PFCGD
5
12
LVS
PFCCS
6
11
RTPH
PFCZCD
7
10
RFPH
PFCVS
8
9
ICB2FL03G
1.2
RFRUN
PG-DSO-16 (150mil)
Figure 2
PG-DSO-16 Package (top view)
Final Data Sheet
9
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Pin Configuration and Functionality
1.3
Pin Functionality
LSGD (low-side gate drive, pin 1)
The gate of the low-side MOSFET in a half-bridge inverter topology is controlled by this pin. There is an active
L-level during UVLO (under voltage lockout) and limitation of the max H-level at 11.0 V during normal operation.
In order to turn on the MOSFET softly (with a reduced diDRAIN/dt); the gate voltage typically rises within 245 ns from
L-level to H-level. The fall time of the gate voltage is less than 50 ns in order to turn off quickly. This measure
produces different switching speeds during turn-on and turn-off as it is usually achieved with a diode parallel to a
resistor in the gate drive loop. It is recommended to use a resistor of typically 10 Ω between drive pin and gate in
order to avoid oscillations and in order to shift the power dissipation of discharging the gate capacitance into this
resistor. The dead time between the LSGD signal and HSGD signal is self-adapting between 1.05 μs and 2.1 μs.
LSCS (low-side current sense, pin 2)
This pin is directly connected to the shunt resistor which is located between the source terminal of the low-side
MOSFET of the inverter and ground.
Internal clamping structures and filtering measures allow for sensing the source current of the low-side inverter
MOSFET without additional filter components.
The first threshold is 0.8 V. If this threshold is exceeded for longer than 500 ns during preheat or run mode, an
inverter overcurrent is detected and causes a latched shutdown of the IC. The ignition control is activated if the
sensed slope at the LSCS pin reaches typically 205 mV/μs ± 25 mV/μs and exceeds the 0.8 V threshold. This
stops the frequency decrease and waits for ignition. The ignition control is now continuously monitored by the
LSCS PIN. The ignition control is designed to handle choke operation in saturation during ignition in order to
reduce the choke size.
If the sensed current signal exceeds a second threshold of 1.6 V for longer than 500 ns during start-up, soft start,
ignition mode and pre-run, the IC changes over into latched shutdown.
There are further thresholds active at this pin during run mode that detect capacitive mode operation. An initial
threshold at 50 mV needs to sense a positive current during the second 50 % on-time of the low-side MOSFET for
proper operation (cap. load 1). A second threshold of -50mV senses the current before the high-side MOSFET is
turned on. A voltage level below this threshold indicates faulty operation (cap. load 2). Finally a third threshold at
2.0 V senses even short overcurrent during turn-on of the high-side MOSFET, typical for reverse recovery currents
of a diode (cap. load 2). If any of these three comparator thresholds indicates incorrect operating conditions for
longer than 620 μs (cap. load 2) or 2500 ms (cap. load 1) in run mode, the IC turns off the gates and changes into
fault mode due to detected capacitive mode operation (non-zero voltage switching).
The threshold of -50 mV is also used to adjust the dead time between turn-off and turn-on of the half-bridge drivers
in a range of 1.05 μs to 2.1 μs during all operating modes.
Vcc (supply voltage, pin 3)
This pin provides the power supply of the ground related section of the IC. There is a turn-on threshold at 14.0 V
and an UVLO threshold at 10.6 V. The upper supply voltage level is 17.5 V. There is an internal zener diode
clamping VCC at 16.3 V (at IVCC = 2 mA typically). The maximum zener current is internally limited to 5 mA. An
external zener diode is required for higher current levels. Current consumption during UVLO and during fault mode
is less than 170 μA. A ceramic capacitor close to the supply and GND pin is required in order to act as a lowimpedance power source for gate drive and logic signal currents. In order to skip preheating after short
interruptions to the mains supply it is necessary to feed the start-up current (160 μA) from the bus voltage. Note:
for external VCC supply, see notes in the flowchart (Section 3.3).
Final Data Sheet
10
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Pin Configuration and Functionality
GND (ground, pin 4)
This pin is connected to ground and represents the ground level of the IC for supply voltage, gate drive and sense
signals.
PFCGD (PFC gate drive, pin 5)
This pin controls the gate of the MOSFET in the PFC preconverter designed in boost topology. There is an active
L-level during UVLO and limitation of the max H-level at 11.0 V during normal operation. In order to turn on the
MOSFET softly (with a reduced diDRAIN/dt), the gate drive voltage rises within 245 ns from L-level to H-level. The
fall time of the gate voltage is less than 50 ns in order to turn off quickly.
A resistor of typically 10 Ω between the drive pin and gate is recommended in order to avoid oscillations and in
order to shift the power dissipation of discharging the gate capacitance into this resistor.
The PFC section of the IC controls a boost converter as a PFC preconverter in discontinuous conduction mode
(DCM). Control usually starts with gate drive pulses with a fixed on-time of typically 4.0 μs at VACIN = 230 V,
increasing up to 24 μs and with an off-time of 47 μs. As soon as sufficient zero current detector (ZCD) signals are
available, the operation mode changes from fixed frequency operation to operation with variable frequency. The
PFC works in critical conduction mode operation (CritCM) when rated and / or medium load conditions are present.
This means triangular-shaped currents in the boost converter choke without gaps and variable operating
frequency. During low loads (detected by an internal compensator) operation is in discontinuous conduction mode
(DCM) – i.e., triangular-shaped currents in the boost converter choke with gaps when reaching the zero current
level and variable operating frequency in order to avoid steps in the consumed line current.
PFCCS (PFC current sense, pin 6)
The voltage drop across a shunt resistor located between the source of the PFC MOSFET and GND is sensed
with this pin. If the level exceeds a threshold of 1.0 V for longer than 200 ns, the PFC gate drive is turned off as
long as the zero current detector (ZCD) enables a new cycle. If no ZCD signal is available within 52 μs after turn-off
of the PFC gate drive, a new cycle is initiated from an internal start-up timer.
PFCZCD (PFC zero current detector, pin 7)
This pin senses the point of time when the current through boost inductor becomes zero during off-time of the PFC
MOSFET in order to initiate a new cycle.
The moment of interest appears when the voltage of the separate ZCD winding changes from the positive to
negative level, which represents a voltage of zero at the inductor windings and therefore the end of current flow
from the lower input voltage level to the higher output voltage level. There is a threshold with hysteresis – for
increasing level 1.5 V, for decreasing level 0.5 V – which detects the change in inductor voltage.
A resistor, connected between ZCD winding and pin 7, limits the sink and source current of the sense pin when
the voltage of the ZCD winding exceeds the internal clamping levels (6.3 V and -2.9 V typically @ 5 mA) of the IC.
If the sensed voltage level of the ZCD winding is not sufficient (e.g. during start-up), an internal start-up timer will
initiate a new cycle every 52 μs after turn-off of the PFC gate drive. The source current flowing out of this pin during
the on-time of the PFC-MOSFET indicates the voltage level of the AC supply voltage. During low input voltage
levels the on-time of the PFC-MOSFET is increased in order to minimize gaps in the line current during zero
crossing of the line voltage and improve the THD (Total Harmonic Distortion) of the line current. Optimization of
the THD is possible by trimming of the resistor between this pin and the ZCD winding.
PFCVS (PFC voltage sense, pin 8)
The intermediate circuit voltage (bus voltage) at the smoothing capacitor is sensed by a resistive divider at this
pin. The internal reference voltage for rated bus voltage is 2.5 V. There are further thresholds at 0.3125 V (12.5 %
of the rated bus voltage) for the detection of open control loop, at 1.875 V (75 % of the rated bus voltage) for the
detection of undervoltage, and at 2.725 V (109 % of the rated bus voltage) for the detection of overvoltage. The
Final Data Sheet
11
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Pin Configuration and Functionality
overvoltage threshold operates with a hysteresis of 100 mV (4 % of the rated bus voltage). For the detection of
successful start-up, the bus voltage is sensed at 95 % (2.375 V). It is recommended to use a small capacitor
between this pin and GND as a spike suppression filter.
In run mode, a PFC overvoltage stops the PFC gate drive within 5 μs. As soon as the bus voltage is less than
105 % of the rated level, the gate drives are enabled again. If the overvoltage lasts for longer than 625 ms, inverter
overvoltage is detected and the inverter turns off the gate drives also. This causes powerdown and powerup when
VBUS < 109 %.
A bus undervoltage (VBUS > 75 %) or inverter overvoltage during run mode is handled as a fault U. In this situation
the IC changes into powerdown mode and generates a delay of 100 ms by an internal timer. Then startup
conditions are checked and if valid, a further startup is initiated. If startup conditions are not valid, a further delay
of 100 ms is generated.
This procedure is repeated a maximum of seven times. If startup is successful within these seven cycles, the
situation is interpreted as a short interruption of the mains supply and the preheating is skipped. Any further startup
attempt is initiated to include the preheating.
RFRUN (set R for run frequency, pin 9)
A resistor from this pin to ground sets the operating frequency of the inverter during run mode. The typical run
frequency range is 20 kHz to 120 kHz. The set resistor R_RFRUN can be calculated, based on the run frequency
fRUN according to the equation:
RFRUN
5 ⋅ 108 ΩHz
=
f RUN
RFPH (set R for preheat frequency, pin 10)
A resistor from this pin to ground, together with the resistor at pin 9, sets the operating frequency of the inverter
during preheating mode. The typical preheating frequency range is from the run frequency (as a minimum) to
150 kHz. The set resistor R_RFPH can be calculated, based on the preheating frequency fPH and the resistor
RRFRUN according to the equation:
RRFPH =
RRFRUN
f PH ⋅ RRFRUN
−1
5 ⋅ 108 ΩHz
RTPH (set R for preheating time, pin 11)
A resistor from this pin to ground sets the preheating time of the inverter during preheating mode. A set resistor
range from zero to 25 kΩ corresponds to a range of preheating times from zero to 2500 ms subdivided into 127
steps, as expressed below:
RRTPH =
t Pr eHeating
ms
100
kΩ
LVS (lamp voltage sense, pin 12)
Before startup this pin senses a current fed from the rectified line voltage via resistors through the high-side
filaments of the lamp for detection of an inserted lamp.
Final Data Sheet
12
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Pin Configuration and Functionality
The sensed current fed into the LVS pin has to exceed 12 μA typically at a voltage level of 6.0 V at the LVS pin.
The reaction on the high side filament detection is mirrored at the RES pin (see pin 13). In addition, the detection
of available mains supply after an interruption is sensed by this pin. Together with the RES pin, the IC can monitor
the lamp removal of one lamp path (series connection of lamps is possible). If the functionality of this pin is not
required, it can be disabled by connecting this pin to ground.
During run mode the lamp voltage is monitored with this pin by sensing a current proportional to the lamp voltage
via resistors. An overload is indicated by an excessive lamp voltage. If the peak-to-peak lamp voltage causes a
peak-to-peak current above a threshold of 210 μAPP for longer than 620 μs, a fault EOL1 (end-of-life) is assumed.
If the DC current at the LVS pin exceeds a threshold of ±42 μA for longer than 2500 ms, a fault EOL2 (rectifier
effect) is assumed. The levels of AC sense current and DC sense current can be set separately by an external RC
network. Note that in the case of deactivation of the LVS PIN, reactivation starts when the voltage at the LVS pin
exceeds VLVSEnable1 in RUN Mode.
RES (restart, pin 13)
A source current flowing out of this pin via resistor and filament to ground monitors the existence of the low-side
filament of the fluorescent lamp for restart after lamp removal. A capacitor from this pin directly to ground
eliminates a superimposed AC voltage that is generated as a voltage drop across the low-side filament. With a
second sense resistor, the filament of a parallel lamp can be included in the lamp removal sensing. Note that
during startup the chip supply voltage Vcc has to be below 14.0 V before VRES reaches the filament detection level.
During typical start-up with connected filaments of the lamp a current source IRES3 (-21.3 μA) is active as long as
VCC > 10.6 V and VRES < VRES1 (1.6 V). An open low-side filament is detected when VRES > VRES1. Such a condition
will prevent the start-up of the IC. In addition, the comparator threshold is set to VRES2 (1.3 V) and the current
source changes to IRES4 (-17.7 μA). The system is then waiting for a voltage level lower than VRES2 at the RES pin
to indicate a connected low-side filament, which will enable the start-up of the IC.
An open high-side filament is detected when there is no sink current ILVSSINK (< 12 μA typ.) into the LVS pin before
the VCC start-up threshold is reached. Under these conditions the current source at the RES pin is IRES1 (-42.6 μA)
as long as VCC > 10.6 V and VRES < VRES1 (1.6 V) and the current source is IRES2 (-35.4 μA) when the threshold
has changed to VRES2 (1.3 V). In this way, the detection of the high-side filament is mirrored at the levels on the
RES pin.
There is a further threshold of 3.2 V active at the RES pin during run mode. If the voltage level rises above this
threshold for longer than 620 μs, the IC changes over into latched fault mode.
In any case of fault detection with different reaction times the IC turns off the gate drives and changes into
powerdown mode with a current consumption of 170 μA max. An internal timer generates a delay time of 200 ms
before start-up conditions are checked again. As soon as start-up conditions are valid, a second start-up attempt
is initiated. If this second attempt fails, the IC remains in latched fault mode until a reset is generated by UVLO or
lamp removal. The RES PIN can be deactivated by setting the PIN to GND (durable).
HSGND (high-side ground, pin 14)
This pin is connected to the source terminal of the high-side MOSFET, which is also the node of the high-side and
low-side MOSFET. This pin represents the floating ground level of the high-side driver and the high-side supply.
HSVCC (high-side supply voltage, pin 15)
This pin provides the power supply of the high-side ground-related section of the IC. An external capacitor between
pins 14 and 15 acts like a floating battery, which has to be recharged cycle by cycle via the high-voltage diode
from low-side supply voltage during on-time of the low-side MOSFET. There is a UVLO threshold with hysteresis
that enables the high-side section at 10.4 V and disables it at 8.6 V.
Final Data Sheet
13
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
HSGD (high-side gate drive, pin 16)
The gate of the high-side MOSFET in a half-bridge inverter topology is controlled by this pin. There is an active
L-level during UVLO and limitation of the max H-level at 11.0 V during normal operation. The switching
characteristics are the same as described for LSGD (pin 1). It is recommended to use a resistor of about 10 Ω
between the drive pin and gate in order to avoid oscillations and in order to shift the power dissipation of
discharging the gate capacitance into this resistor. The dead time between LSGD signal and HSGD signals is
self-adapting between 1.05 μs and 2.1 μs (typically).
2
Functional Description
This section describes applications and functionality of the chip.
2.1
Typical Application Circuitry
The schematic shown in Figure 3 shows a typical application for a T5 single fluorescent lamp. It is designed for
universal input voltage from 90 VAC up to 270 VAC. The following sections explain the components in reference to
this schematic.
R13
D5
C1
PFCZCD
R35
LVS
L101 D1...4
R41
R34
L1
R14
PFCVS
R11
PFCCS
R12
R18
DR12
LSGD
C11 R20
D9
C12
Q2
R26
R45
C15
C24
Q3
C14
R27
C16
D6
D7
R30
R21R22R23
C13
L2
C17
LSCS
RFPH
GND
C2
HSGND
RES
C10
C40
HSVCC
RTPH
PFCGD
R16
R2
RFRUN
90 ...
270 VAC
R15
Q1
VCC
R1
ICB2FL03G
HSGD
R42 R43 R44
D8
R36
C19
R25
Figure 3
Application Circuit of Ballast for a Single Fluorescent Lamp (FL)
2.2
Normal Startup
This section describes the basic operation flow (8 phases) from the UVLO (Under Voltage Lock Out) into run mode
without any error detection. For detailed information see Section 2.2.1 and Section 2.2.2. Figure 4 shows the 8
different phases during a typical start from UVLO (phase 1, Figure 4) to run mode (phase 8, Figure 4) and then
into normal operation (no failure detected).
If the AC line input is switched ON, the VCC voltage rises to the UVLO threshold VCC = 10.6 V (no IC activity during
UVLO). If VCC exceeds the first threshold of VCC = 10.6 V, the IC starts the first level of detection activity, the high
and low side filament detection during the start-up hysteresis (phase 2, Figure 4).
Final Data Sheet
14
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
Frequency /
Lamp Voltage
135 kHz
Frequency
100 kHz
50 kHz
42 kHz
1
2
3
60ms
35ms
80ms
4
11ms
5
Lamp Voltage
0 - 2500 ms
6
40 - 237ms
7
625 ms
0 kHz
Rated BUS
Voltage VBUS
8
Mode /
Time
100 %
Rated BUS Voltage
95 %
30 %
Mode /
Time
Chip Supply
Voltage VCC
VCC = 17.5 V
Chip Supply Voltage
VCC = 14.0 V
VCC = 10.6 V
VCC = 0 V
UVLO
Figure 4
Monitoring
Start Up Soft Start
Preheating
Ignition
Pre-Run
Mode /
Time
Run Mode
into normal Operation
Typical Startup Procedure in Run Mode (in Normal Operation)
Followed at the end of the start-up hysteresis (phase 2, Figure 4) VCC > 14.0 V and before phase 3 is active, a
second level of detection activity senses for 130 μs (propagation delay of the IC) whether the bus voltage is
between 12.5 % and 105 %. If the previous bus voltage conditions are fulfilled and the filaments are detected, the
IC starts the operation with an internally fixed startup frequency of typically 135 kHz (all gates are active). If the
bus voltage reaches a level of 95 % of the rated bus voltage within 80 ms at the latest (phase 3, Figure 4), the IC
enters the soft start phase. During soft start (phase 4 , Figure 4), the start-up frequency shifts from 135 kHz down
to the set preheating frequency (Section 2.2.2). In the soft start phase, the lamp voltage rises and the chip supply
voltage reaches its working level from 10.6 V < VCC < 17.5 V. After the soft start has finished, the IC enters the
preheating mode (phase 5, Figure 4) for preheating the filaments (adjustable time) in order to extend the life cycle
of the FL filaments. On finishing preheating, the controller starts ignition (phase 6, Figure 4). During the ignition
phase, the frequency decreases from the set preheating frequency down to the set operation frequency
(adjustable, see Section 2.2.2). If ignition is successful, the IC enters the pre-run mode (phase 7, Figure 4).
This mode is provided in order to prevent a malfunction of the IC due to an unstable system – e.g., the lamp
parameters are not in a steady state condition. After finishing the 625 ms pre-run phase, the IC switches over to
the run mode (phase 8, Figure 4) with complete monitoring.
Final Data Sheet
15
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
2.2.1
Operating Levels from UVLO to Soft Start
This section describes the operating flow from phase 1 (UVLO) to phase 4 (soft start) in detail. The control of the
ballast is able to start the operation within less than 100 ms (IC in active mode). This is achieved by a small startup capacitor (about 1 μF C12 and C13 – fed by start-up resistors R11 and R12 in Figure 3) and the low current
consumption during the UVLO (IVCC = 130 μA – phase 1, Figure 5) and start-up hysteresis (IVCC = 160 μA – defines
the start-up resistors – phase 2, Figure 5) phases. The chip supply stage of the IC is protected against overvoltage
via an internal Zener clamping network, which clamps the voltage at 16.3 V and allows a current of 2.5 mA. For
clamping currents above 2.5 mA, an external Zener diode (D9, Figure 3) is required.1)
Frequency /
Lamp Voltage
Frequency
135 kHz
100 kHz
Lamp Voltage
VBUS
100 %
95 %
30 %
VCC
17.5 V
16.0 V
14.0 V
10.6 V
1
2
UVLO
Monitoring
3
4
Start Up Soft Start
I VCC
< 6.0 mA + IGate
< 160 µA
130 µA
VRES
1.6 V
- 21.3 µA
IRES
ILVS
> 18 µA
Figure 5
1)
< 210µApp
Typical Startup Procedure in Run Mode (in Normal Operation)
IGate depends on MOSFET
Final Data Sheet
16
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
If VCC exceeds the 10.6 V level and stays below 14.0 V (start-up hysteresis – phase 2, Figure 5), the IC checks
whether the lamps are assembled by detecting a current across the filaments.
The low side filaments are checked from a source current of typical IRES3 = - 21.3 μA flowing out of pin 13 RES
(Figure 5 IRES). This current produces a voltage drop of VRES < 1.6 V (filament is ok) at the low side filament sense
resistor (R 36 in Figure 3), connected to GND (via low side filament). An open low side filament is detected (see
Section 2.3.2), when the voltage at the RES pin exceeds the VRES > 1.6 V threshold (Figure 5 VRES).
The high side filaments are checked by a current of ILVS > 12 μA typically via resistors R41, R42, R43 and R44
(Figure 3) into the LVS pin 12 (for a single lamp operation). An unused LVS pin has to be disabled via connection
to GND. An open high side filament is detected (see Section 2.3.3) when there is no sink current into the LVS pin.
This causes a higher source current out of the RES pin (typically 42.6 μA / 35.4 μA) in order to exceed VRES >
1.6 V. In the case of defective filaments, the IC keeps monitoring until an adequate current from the RES or the
LVS pin is present (e.g. in case of removal of a defective lamp).
When VCC exceeds the 14.0 V threshold – by the end of the start-up hysteresis in phase 2 , Figure 5 – the IC waits
for 130 μs and senses the bus voltage. If the rated bus voltage is in the corridor of 12.5 % < VBUSrated < 105 %, the
IC powers up the system and enters phase 3 (Figure 5 VBUSrated > 95 % sensing); if not, the IC initiates a UVLO
until the chip supply voltage falls below VCC < 10.6 V. As soon as the condition for a power-up is fulfilled, the IC
starts the inverter gate operation with an internal fixed start-up frequency of 135 kHz. The PFC gate drive starts
with a delay of approx. 300 μs. Next, the bus voltage will be checked for a rated level above 95 % for a duration
of 80 ms (phase 3, Figure 5). When leaving phase 3, the IC enters the soft start phase and shifts the frequency
from the internal fixed start-up frequency of 135 kHz down to the set preheating frequency – e.g. fRFPH = 100 kHz.
2.2.2
Operating Levels from Soft Start to Run Mode
This section describes the operating flow from phase 5 (preheating mode) to phase 8 (run mode) in detail. In order
to extend the lifetime of the filaments, the controller enters – after the soft start phase – the preheating mode
(phase 5, Figure 6). The preheating frequency is set by resistors R22 pin RFPH to GND in combination with R21
(Figure 3) typ. 100 kHz e.g. R22 = 8.2 kΩ in parallel to R21 = 11.0 kΩ (see Figure 3, RFRUN pin). The preheating
time can be selected by the programming resistor (R23 in Figure 3) at pin RTPH from 0 ms up to 2500 ms
(phase 5, Figure 6).
135kHz
f,V
Frequency
65kHz
50kHz
3
4
6
5
7
8
40kHz
Lamp Voltage
10ms
Start-Up Softstart
0-2500ms
Preheating
40-237ms
625ms
Ignition
Pre-Run
t
Normal Operation
Run
VLSCS
0.8 V
Softstart proceeds in 15 steps à 650µs according ΔfPH = (135kHz - fPH )/ 15steps.
Ignition proceeds in 127 steps à 324µs according ΔfIGN = (f PH - f RUN)/ 127steps.
Preheating Frequency with 8.7 kΩ Resistor from PIN RFPH to GND
RUN Frequency with a 12.0 kΩ Resistor from PIN RFRUN to GND
Figure 6
Typical Variation of Operating Frequency during Startup
Final Data Sheet
17
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
During ignition (phase 6, Figure 6), the operating frequency of the inverter is shifted downward in ttyp = 40 ms
(tmax = 237 ms) to the run frequency set by a resistor (R21 in Figure 3) at pin RFRUN to GND (typically 45 kHz
with an 11.0 kΩ resistor). During this frequency shifting, the voltage and current in the resonant circuit will rise
when the operation is close to the resonant frequency with increasing voltage across the lamp. The ignition control
is activated if the sensed slope at the LSCS pin reaches typically 205 mV/μs ± 25 mV/μs and exceeds the 0.8 V
threshold. This stops the decrease of the frequency and waits for ignition. The ignition control is now continuously
monitored by the LSCS pin. The maximum duration of the ignition procedure is limited to 237 ms. If there is no
ignition within this time frame, the ignition control is disabled and the IC changes over into the latched fault mode.
Furthermore, in order to reduce the size of the lamp choke, the ignition control is designed to operate with a lamp
choke in magnetic saturation during ignition. For operation in magnetic saturation during ignition; the voltage at
the shunt at the LSCS pin 2 has to be VLSCS = 0.75 V when the ignition voltage is reached. If ignition is successful,
the IC enters the pre-run mode (phase 7, Figure 6). The pre-run mode is a safety mode in order to prevent a
malfunction of the IC due to an unstable system – e.g., the lamp parameters are not in a steady state condition.
After 625 ms pre-run mode, the IC changes to the run mode (phase 8, Figure 6). The run mode monitors the
complete system regarding bus over- and undervoltage, open loop, overcurrent of PFC and / or inverter, lamp
overvoltage (EOL1) and rectifier effect (EOL2) (see Section 2.5) and capacitive loads 1 and 2 (see Section 2.6).
Figure 8 shows the lamp voltage versus the frequency during the different phases from preheating to the run
mode. The lamp voltage rises by the end of the preheating phase with decreasing frequency (e.g., 100 kHz to
50 kHz) up to, for example, 700 V during ignition. After ignition, the lamp voltage drops down to its working level
with continuous decreasing of the frequency (Figure 8) down to its working level e.g. 45 kHz (set by a resistor at
the RFRUN pin to ground). After decreasing of the frequency stops, the IC enters the pre-run mode.
Lamp Voltage [V]
Lamp Voltage vs Frequency @ different Modes
1000
1000
900
900
800
800
700
700
IGNITION
600
600
Operation without Load
500
500
400
400
300
300
200
100
200
Operation with Load
0
10000
PRE Run
and
RUN Mode
After
IGNITION
100
Pre Heating
0
100000
Frequency [Hz]
After Ignition
Figure 7
Before Ignition
Lamp Voltage versus Frequency during the different Startup Phases
Final Data Sheet
18
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
2.3
Filament Detection during Start-Up and Run Mode
The low and high side filament detection is sensed via the RES and the LVS pins. The low side filament detection
during start-up and run mode is detected via the RES pin only. An open high side filament during start-up will be
sensed via the LVS and the RES pins.
2.3.1
Start-Up with broken Low Side Filament
A source current of IRES3 = -21.3 μA from the RES pin (13) monitors the existence of a low side filament during a
start-up (also in run mode). In the case of an open low side filament during the start-up hysteresis (10.6 V < VCC
< 14.0 V) a capacitor (C19 in Figure 3) will be charged up via IRES3 = -21.3 μA. When the voltage at the RES pin
(13) exceeds VRES1 = 1.6 V, the controller prevents a power up and clamps the RES voltage internally at VRES
= 5.0 V. The gate drives of the PFC and inverter stage do not start working.
VCC
Start UP with open LOW Side Filament
17.5 V
16.0 V
Chip Supply Voltage
14.0 V
10.6 V
VRES
UVLO
Start Up
Hysteresis
5.0 V
Time
No Power UP
1.6 V
1.3 V
Time
I RES
21.3µA
17.7µA
Time
VLamp
Time
Figure 8
Start-Up with Open Low Side Filament
Restart from open LOW Side Filament
17.5 V
16.0 V
Chip Supply Voltage
PFC Gate Drive
10.0 V
Time
VRES
5.0 V
Timer t = 100 ms
Latch Mode
1.6 V
1.3 V
Power UP into RUN Mode
1
2
3
Time
IRES
21.3µA
17.7µA
Time
VLamp
Time
Figure 9
Restart from Open Low Side Filament
Final Data Sheet
19
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
The IC comparators are then set to a threshold of VRES1 = 1.3 V and to IRES4 = - 17.7μA, the controller waits until
the voltage at the RES pin drops below VRES1 = 1.3 V.
When a filament is present (Figure 9, section 2), the voltage drops below 1.3 V and the value of the source current
out of the RES pin is set from IRES4 = -17.7 μA up to IRES3 = -21.3 μA. The controller then powers up the system,
including soft start and preheating, into the run mode.
2.3.2
Low Side Filament Detection during Run Mode
In the case of an open low side filament during run mode, the current flowing out of the RES pin IRES3 = -21.3 μA
charges up the capacitor C19 in Figure 3. If the voltage at the RES pin exceeds the VRES3 = 3.2 V threshold, the
controller detects an open low side filament and stops the gate drives after a delay of t = 620 μs of an internal timer.
Open LOW Side Filament during Run Mode
VCC / VPFCGD
17.5 V
16.0 V
Chip Supply Voltage
10.0 V
PFC Gate Drive
Time
VRES
Latch Mode
5.0 V
3.2 V
1.6 V
1.3 V
Fault Event
IRES
21.3µA
Time
17.7µA
Time
VLamp
Delay t = 620µs
Time
Figure 10
Open Low Side Filament Run Mode
Restart from open LOW Side Filament
17.5 V
16.0 V
Chip Supply Voltage
PFC Gate Drive
10.0 V
Time
VRES
5.0 V
Timer t = 100 ms
Latch Mode
1.6 V
1.3 V
Power UP into RUN Mode
1
2
3
Time
IRES
21.3µA
17.7µA
Time
VLamp
Time
Figure 11
Restart from Open LS Filament
Final Data Sheet
20
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
A restart is initiated when a filament is detected e.g. in the case of a lamp removal. If a filament is present
(Figure 11, section 2), the voltage drops below 1.3 V and the value of the source current flowing out of the RES
pin is set from IRES4 = -17.7 μA up to IRES3 = -21.3 μA. The controller powers up the system, including soft start and
preheating, into the run mode (Figure 11, section 3).
2.3.3
Start-Up with Broken High Side Filament
An open high side filament during the start-up hysteresis (10.6 V < VCC < 14.0 V) is detected when the current into
the LVS pin 12 is below ILVS = 12 μA (typically). In that case, the current flowing out of the RES pin 13 rises up to
IRES1 = -42.6 μA. This causes the voltage at the RES pin to cross VRES1 = 1.6 V. The source current is now set to
IRES2 = -35.4 μA and another threshold of VRES2 = 1.3 V is active. The controller prevents a power-up (see
Figure 12), and the gate drives of the PFC and inverter stage do not start working.
VCC
Start UP with OPEN HIGH Side Filament
17.5 V
16.0 V
Chip Supply Voltage
14.0 V
10.6 V
Time
VRES UVLO Start Up
Hysteresis
2.0 V
1.6 V
1.3 V
No Power UP
Time
I RES
42.6µA
35.4µA
IRES
21.3µA
17.7µA
Time
ILVS
12µA
ILVS
VLamp
Time
Time
Figure 12
Start-Up with Open High Side Filament
Final Data Sheet
21
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
VCC
17.5 V
16.0 V
Restart from open HIGH Side Filament
Chip Supply Voltage
14.0 V
10.6 V
Time
VRES
2.0 V
1.6 V
1.3 V
No Power Up
Power UP (into RUN Mode)
IRES
42.6µA
35.4µA
Time
I RES
21.3µA
17.7µA
Time
I LVS
12µA
ILVS
VLamp
Time
Time
Figure 13
Restart from Open High Side Filament
When the high side filament is present, e.g. insertion of a lamp, the current of the active LVS pin exceeds ILVS >
12 μA (typically), the RES current drops from IRES2 = -35.4 μA down to IRES4 = -17.7 μA (Figure 13). The controller
then senses the low side filament. If a low side filament is also present, and the controller drops (after a short delay
due to a capacitor at the RES pin) below VRES2 = 1.3 V, the RES current is set to IRES3 = -21.3 μA, and the controller
powers up the system.
Final Data Sheet
22
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
2.4
PFC Preconverter
2.4.1
Discontinuous Conduction and Critical Conduction Mode Operation
The digitally controlled PFC preconverter starts with an internally fixed ON time of typically tON = 4.0 μs and a
variable frequency. The ON time is increased every 280 μs (typical) up to a maximum ON time of 24 μs. The
control switches practically immediately from the discontinuous conduction mode (DCM) to critical conduction
mode (CritCM) as soon as a sufficient ZCD signal becomes available. The frequency range in CritCM is 22 kHz
to 500 kHz depending on the power (Figure 14), with a variation of the ON time from 24 μs > tON > 0.5μs.
Discontinuous Conduction Mode (DCM) <> Critical Condution Mode (CritCM)
100,00
1000,00
100,00
Nominal Load
Frequency @ DCM Operation
10,00
10,00
Light Load
ON Time Hysteresis
PRE HEATING
ON Time @ CritCM Operation
Increasing Power
1,00
PFC - ON Time [µs]
PFC Frequency [kHz] 50% Duty Cycle
Frequency @ CritCM Operation
1,00
ON Time @ DCM Operation
Decreasing Power
0,10
ON Time Hysteresis
in RUN MODE
0,01
0,10
0,01
0,10
1,00
10,00
100,00
Normalized Output Power [% ]
Frequency DCM
Figure 14
Frequency CritCM
Ton DCM
Ton CritCM
Operating Frequency and ON Time versus Power in DCM and CritCM Operation
For lower loads (POUTNorm < 8 % from the normalized load1)) the control operates in discontinuous conduction mode
(DCM) with an ON time from 4.0 μs and increasing OFF time. The frequency during DCM is variable in a range
from 144 kHz down to typically 22 kHz @ 0.1 % load (Figure 14). With this control method, the PFC converter
enables stable operation from 100 % load down to 0.1 %. Figure 14 shows the ON time range in DCM and CritCM
(Critical Conduction Mode) operation. In the overlapping area of CritCM and DCM there is a hysteresis of the ON
time which causes a negligible frequency change.
2.4.2
PFC Bus Voltage Sensing
Overvoltage, open loop, bus 95 % and undervoltage states (Figure 15) of the PFC bus voltage are sensed at the
PFCVS pin via the network R14, R15, R20 and C11 – Figure 3 (C11 acts as a spike suppression filter).
1)
Normalized power @ low line input voltage and maximum load
Final Data Sheet
23
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
2.4.2.1
Bus Overvoltage and PFC Open Loop
The bus voltage loop control is completely integrated (Figure 16) and provided by an 8-bit sigma/delta A/D
converter with a typical sampling rate of 280 μs and resolution of 4 mV/bit. After leaving phase 2 (monitoring), the
IC starts power-up (VCC > 14.0 V). After power-up, the IC senses the bus voltage below 12.5 % (open loop) or
above 105 % (bus overvoltage) for 130 μs. In the case of bus overvoltage (VBUSrated > 109 %) or open loop
(VBUSrated < 12.5 %) in phases 3 to 8, the IC shuts off the gate drives of the PFC within 5 μs or 1 μs respectively.
In this case, the PFC restarts automatically when the bus voltage is within the corridor (12.5 % < VBUSrated < 105 %)
again. Is the bus voltage valid after 130 μs, the bus voltage sensing is set to 12.5 % < VBUSrated < 109 %. If these
thresholds are exceeded for longer than 1 μs (open loop) or 5 μs (overvoltage), the PFC gate drive stops working
until the voltage drops below 105 % or exceeds the 12.5 % level. If the bus overvoltage (> 109 %) lasts for longer
than 625 ms in run mode, the inverter gates also shut off and a power-down with complete restart is attempted
(Figure 15).
Rated BUS
Voltage V BR
1
2
V PFCVS = 2.725V
V PFCVS = 2.625V
109 %
105 %
3
6
5
7
8
Typical rated Bus Voltage Level
V PFCVS = 2.500V
100 %
95 %
V PFCVS = 2.375V
VBR < 95%
V PFCVS = 1.875V
75 %
30 %
12.5 %
0%
4
BUS Over Voltage: Stops PFC Gate Drive within 5µs Auto Restart when VBR < 109 % / t > 625ms PD VBR < 105% Æ Fault U
V PFCVS = 0.313 V
35ms
t < 800ms AR without Preheating
t > 800ms AR with Preheating
PFC Open Loop / keeps all Gate Drives within 1µs Auto Restart / t > 1µs Stops PFC FET till VBR > 12.5%Æ AR
VCC < 10.6 VV CC < 14.1 V
60ms
Under Voltage V BR < 75%
VBUS>95% Soft Start
130 µs
80ms
11ms
Preheating
Ignition
Pre-Run
0 - 2500 ms
40 - 237ms
625ms
Run Mode into normal Operation
ERROR Corridor
Figure 15
PFC Bus Voltage Operating Level and Error Detection
2.4.2.2
Bus Voltage 95 % and 75 % Sensing
Mode /
Time
AR = Auto Restart
PD = Power Down
CbC = Cycle by Cycle
When the rated bus voltage is in the corridor of 12.5 % < VBUSrated < 109 %, the IC will check whether the bus
voltage exceeds the 95 % threshold (Figure 15, phase 3) within 80 ms before entering the soft start phase 4.
Another threshold is activated when the IC enters the run mode (phase 8). If the rated bus voltage drops below
75 % for longer than 84 μs, a power-down with a complete restart is attempted when a counter exceeds 800 ms.
In the case of short-term bus undervoltage (the bus voltage reaches its working level in run mode before exceeding
typically 800 ms (min. 500 ms)) the IC skips phases 1 to 5 and starts with ignition (see Section 2.7.1 for conditions
for emergency lighting). The internal reference level of the bus voltage sense VPFCVS is 2.5 V (100 % of the rated
bus voltage) with a high accuracy. A surge protection is activated in the case of a rated bus voltage of VBUS >
109 % and a low side current sense voltage of VLSCS > 1.6 V in pre-run mode, or VLSCS > 0.8 V in run mode for
longer than 500 ns.
Final Data Sheet
24
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
2.4.3
PFC Structure of Mixed Signals
A digital NOTCH filter eliminates the input voltage ripple independently of the mains frequency. A subsequent error
amplifier with PI characteristic ensures stable operation of the PFC preconverter (Figure 16).
Over Voltage
109%
Open Loop
12.5%
PFCGD
PFCVS
Σ∆-ADC
Notch Filter
PI Loop Control
PWM
Under Voltage
75%
Over Current
1V ± 5.0%
Bus Voltage
95%
ZCD Start Up
1.5V / 0.5V
Gate Drive
PFCCS
PFCZCD
THD
Correction
Int. Reference
VPFCVS = 2.5 V
Figure 16
Clock 870 kHz
Structure of the Mixed Digital and Analog Control of the PFC Preconverter
The zero current detection (ZCD) is sensed by the PFCZCD pin via R13 (Figure 3). Notification of finished current
flow during demagnetization is required in CritCM and in DCM also. The input is equipped with a special filtering
system, including blanking of typically 500 ns and a large hysteresis of typically 0.5 V and 1.5 V VPFCZCD
(Figure 16).
2.4.4
THD Correction via ZCD Signal
An additional feature is the THD correction (Figure 16). In order to optimize the improved THD (especially in the
zones A shown in Figure 17 ZCD @ AC Input Voltage), there is a possibility to extend the pulse width of the gate
signal (blue part of the PFC gate signal in Figure 17) with the variable PFC ZCD resistor (see resistor R13 in
Figure 3) in addition to the gate signal controlled by the VPFCVS signal (gray part of the PFC gate signal in
Figure 17).
Final Data Sheet
25
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
ZCD @ AC Input Voltage
ZCD @ DC Input Voltage
Rectified
AC Input Voltage
A
B
DC Input Voltage
A
0
Voltage at
0
ZCD-Winding
PFC Gate
Drive Voltage 0
PFC gate signal (gray) controlled by the VPFCVS
PFC gate signal (blue) controlled by the ZCD
Figure 17
THD Optimization using adjustable Pulse Width Extension
In the case of DC input voltage (see DC input voltage in Figure 17), the pulse width gate signal is fixed as a
combination of the gate signal controlled by the VPFCVS pin (gray) and the additional pulse width signal controlled
by the ZCD pin (blue) shown in Figure 17 ZCD @ DC input voltage.
The PFC current limitation at pin PFCCS interrupts the ON time of the PFC MOSFET if the voltage drop at the
shunt resistors R18 (Figure 3) exceeds VPFCCS = 1.0 V (Figure 16). This interrupt will restart after the next
sufficient signal from ZCD becomes available (Auto Restart). The first value of the resistor can be calculated by
the ratio of the PFC mains choke and ZCD winding by the bus voltage and a current of typically 1.5 mA (see
equation below for a good practical value of resistance of ZCD). An adjustment of the ZCD resistor causes an
optimized THD.
RZCD
2.5
N ZCD
*VBUS
N PFC
=
1.5mA
Detection of End-of-Life and Rectifier Effect
Two effects are present by End of Life (EOL): lamp overvoltage (EOL1) and a rectifier effect (EOL2).
After ignition (see 1 in Figure 18), the lamp voltage breaks down to its run voltage level with decreasing frequency.
On reaching the run frequency, the IC enters the pre-run mode for 625 ms. During this period, the EOL detection
is still disabled. In the subsequent run mode (2 in Figure 18) the detection of EOL1 (lamp overvoltage; see 3,
Figure 18) and EOL2 (rectifier effect; see 4, Figure 18) is enabled completely.
Final Data Sheet
26
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
Lamp voltage
Pos. Ignition Level
Pos. AC Level
for EOL1 Detection
Positive DC Level
for EOL2 Detection
Negative DC Level
for EOL2 Detection
1
2
3
4
0
t
t
Neg. AC Level
for EOL 1 Detection
Neg. Ignition Level
Normal Operation
Ignition
EOL1
Lamp Overvoltage
Figure 18
End of Life and Rectifier Effect
2.5.1
Detection of End of Life 1 (EOL1) – Lamp Overvoltage
EOL2
Rectifier Effect
The event of EOL1 is detected by measuring the positive and negative peak levels of the lamp voltage via an AC
current fed into the pin LVS (Figure 19). This AC current is fed into the LVS pins via the network R41, R42, R43,
R44 and the low pass filter C40 and R45 – see Figure 3. If the sensed AC current exceeds 210 μAPP for longer
than 620 μs, the status of end-of-life (EOL1) is detected (lamp overvoltage/overload; see Figure 19 LVSAC
current). The EOL1 fault results in a latched power-down mode (after trying a single restart). The controller
continuously monitors the status until the EOL1 status changes – e.g. a new lamp is inserted.
Lamp Voltage
Pos. AC Level
for EOL1 Detection
3
2
0
t
Neg. AC Level
for EOL1 Detection
LVSAC Current
Normal Operation
EOL1
Lamp Overvoltage
105µAPeak
3
2
t
0
- 105µAPeak
EOL1 Detection
Figure 19
t = 620 µs
End of Life (EOL1) Detection, Lamp Voltage versus AC LVS Current
Final Data Sheet
27
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
2.5.2
Detection of End of Life 2 (EOL2) – Rectifier Effect
The rectifier effect (EOL2) is detected by measuring the positive and negative DC levels of the lamp voltage via a
current fed into the LVS pin (Figure 20). This current is fed into the LVS pin via the network R41, R42, R43 and
R44 (see Figure 3). If the sensed DC current exceeds ± 42 μA (Figure 20 LVSDC current) for longer than
2500 ms, the status of end-of-life (EOL2) is detected. The EOL2 fault results in a latched power-down mode (after
trying a single restart) and the controller is continuously monitoring. The insertion of a new lamp or an interruption
of the input voltage resets the status of the IC.
Lamp Voltage
2
4
Pos. DC Level
for EOL2 Detection
0
t
Neg. DC Level
for EOL2 Detection
LVSDC Current
Normal Operation
EOL2
Rectifier Effect
42 µA
0
t
- 42 µA
EOL2 Detection
t = 2500 ms
Figure 20
End of Life (EOL2) Detection, Lamp Voltage versus DC LVS Current
2.6
Detection of Capacitive Load
In order to prevent a malfunction in the area of capacitive load (see Figure 21) during run mode due to certain
deviations from the normal load (e.g. harmed lamp, sudden break of the lamp tube …), the IC has three integrated
thresholds – sensed only via the LSCS (pin 2). The controller distinguishes between two different states of
capacitive load: detection of working without load (idling detection, CapLoad 1) and working with short overcurrent
(CapLoad 2). This state (CapLoad 2) affects operation below the resonance in the capacitive load area
(Figure 23). In both cases, the IC results in a latched power-down mode after a single restart. After latching the
power-down mode, the controller continuously monitors the input voltage and lamp filaments, and restarts after
interruption of the input voltage or insertion of a new lamp.
Final Data Sheet
28
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
Lamp Voltage vs Frequency @ different Modes
1000
1000
900
900
Area of Inductive
Load Behavior
Lamp Voltage [V]
800
700
600
Area of Capacitive
Load Behavior
800
700
IGNITION
600
500
500
400
400
300
300
200
100
200
Load
PRE Run
and
RUN Mode
0
10000
100
After
IGNITION
Pre Heating
0
100000
Frequency [Hz]
After Ignition
Before Ignition
Figure 21
Capacitive and Inductive Operation
2.6.1
Capacitive Load 1 (Idling Detection – Current Mode Preheating)
A capacitive load 1 operation (idling) is detected when the voltage at the LSCS pin is below +50 mV during the
second 50 % ON time of the low side MOSFET (see capacitive load 1 (idling) in Figure 22). If this status is present
for longer than 2500 ms, the controller triggers a latched power-down mode after trying a single restart. The
controller keeps monitoring the status continuously until an adequate load is present (e.g. lamp removal); then the
IC changes to normal operation.
Capacitive Load 1 Operation (Ballast with Current Mode Preheating)
Normal Operation
Capacitive Load 1 (Idling)
VDSLS
VDSLS
IDSLS
IDSLS
VGateHS
VGateHS
VGateLS
VGateLS
VLSCS
VLSCS
2nd 50%
ON Time
2nd 50%
ON Time
+ 50 mV
+ 50 mV
t CAPLOAD 1
Figure 22
tCAPLOAD 2
tCAPLOAD 1
Capacitive Mode 1 Operation without Load during Run Mode
Final Data Sheet
29
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
2.6.2
Capacitive Load 2 (Overcurrent / Operation below Resonance)
A capacitive load 2 operation is detected if the voltage at the LSCS pin drops below a second threshold of
VLSCS = –50 mV directly before the high side MOSFET is turned on or exceeds a third threshold of VLSCS = 2.0 V
during ON switching of the high side MOSFET. If this overcurrent is present for longer than 620 μs, the IC triggers
a latched power-down mode after trying a single restart. The controller keeps monitoring the status continuously
until an adequate load is present e.g. a new lamp is inserted; then the IC changes to normal operation.
Normal Operation
Capacitive Load 2 (Over Current )
VDSLS
VDSLS
IDSLS
IDSLS
VGateHS
VGateHS
VGateLS
VGateLS
VLSCS
VLSCS
+ 2.0 V
+ 2.0 V
- 50 mV
- 50 mV
tCAPLOAD 2
tCAPLOAD 2
Figure 23
Capacitive Mode 2 – Operation with Overcurrent
2.6.3
Adjustable Self-adapting Dead Time
The dead time between the turn OFF and turn ON of the half-bridge drivers is adjustable (C16, see Figure 3) and
is detected via a second threshold (–50 mV) of the LSCS voltage. The range of the dead time adjustment is 1.05 μs
up to 2.1 μs during all operating modes. The start of the dead time measurement is the OFF switching of the high
side MOSFET. The end of the dead time measurement is when VLSCS drops for longer than typically 200 ns
(internal fixed propagation delay) below –50 mV. This time will be stored (stored dead time) and the low side gate
driver switches ON. The high side gate driver turns ON again after OFF switching of the low side switch and the
stored dead time.
Normal Operation in RUN Mode
VDSLS
VLSCS
VLSCS = -50mV
END of Dead Time
Measurement
Gate LS
Gate HS
Dead Time
START of Dead Time
Measurement
Dead Time
200 ns
Propagation Delay
Stored Dead Time
Figure 24
Stored Dead Time
Dead Time of ON and OFF of the Half-Bridge Drivers
Final Data Sheet
30
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
2.7
Emergency Lighting
Line interruptions (bus voltage drops) are detected by the PFCVS. If the rated PFC bus voltage drops below
VBUSRated < 75 % during run mode, the controller detects PFC bus undervoltage. In order to meet the emergency
lighting standards, the controller distinguishes between two different states of PFC bus undervoltage: short- and
a long-term PFC bus undervoltage. A timer increases the time as long as bus undervoltage is present. Short-term
bus undervoltage is detected if the timer value stays below t < 800 ms typical (500 ms min.) after the bus voltage
reaches the nominal level again. This causes a restart without preheating (emergency standard of VDE0108) –
see Figure 25. If the timer exceeds t > 800 ms, the controller forces a complete restart of the system due to longterm bus undervoltage (Figure 26).
2.7.1
Short-term PFC Bus Undervoltage
Short-term PFC bus undervoltage (Figure 25) is detected if the duration of the undervoltage does not exceed
800 ms (timer stays below t < 800 ms, see Figure 25). In that case, the PFC and inverter drivers are immediately
switched off and the controller continuously monitors the status of the bus voltage in a latched power-down mode
(ICC < 170 μA). If the signal at the LVS pin exceeds 18 μA and the rated bus voltage is above 12.5 % while the
timer is below t < 800 ms, the controller restarts from power up without preheating. The timer resets to 0 when
entering run mode.
Bus Voltage Drop for t < 800 ms
Restart without Preheating
VBUSRated
Interrupt for
t < 800 ms
100%
75%
Power Down
Mode
Ignition
RUN Mode
Pre Run
Run Mode
VCC
16V
I CC
< 6 mA +
I QGate
< 6 mA + I QGate
< 160 µA
Timer
t = 800ms
I Preheating
VLamp
Figure 25
BUS Voltage Drop below 75% (rated Bus Voltage) for t < 800 ms during RUN Mode
Final Data Sheet
31
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
2.7.2
Long-term PFC Bus Undervoltage
If the duration of the bus undervoltage exceeds t > 800 ms (see Figure 26), the controller forces an undervoltage
lockout (UVLO). The chip supply voltage drops below VCC = 10.6 V and the chip supply current is below ICC
< 130 μA. When the Vcc voltage exceeds the 10.6 V threshold again, the IC current consumption is below ICC
< 160 μA. In that case, the controller resets the timer and restarts with the full start-up procedure, including
monitoring, power-up, start-up, soft start, preheating, ignition, pre-run and run modes, as shown in Figure 26.
Bus Voltage Drop for t > 800 ms
Restart with full Start Procedure
VBUSRated
Interrupt for t > 800 ms
95%
< 160 µA
UVLO
Monitoring
Power UP
Start Up
Soft Start
< 6 mA +
I Gate
Pre Run
Power Down Mode
Ignition
RUN Mode
VCC
Preheating
75%
Run Mode
16V
UVLO @ 10.6V
ICC
<160 µA
< 6 mA + I Gate
Timer
t = 800ms
IPreheating
VLamp
Figure 26
BUS Voltage Drop below 75% (rated Bus Voltage) for t > 800 ms during RUN Mode
2.8
Built-in Customer Test Mode Operation
In order to decrease the final ballast testing time for customers, the 2nd generation of ballast IC supports an
integrated built-in Customer Test Mode and several functions to disable some features and states of the IC.
2.8.1
Preheating Test Mode
This feature forces the IC to stay in the preheating mode (see Section 2.8.1.2) or to start ignition immediately
without any preheating (see Section 2.8.1.1). A resistor at this pin defines the duration of the preheating phase.
Normally, the preheating phase is in a range of 0 ms up to 2500 ms set via a resistor RRTPH = 0 Ω up to 25 kΩ from
the RTPH pin to GND. The preheating phase is skipped when the RTHP pin is set to GND. If the signal at this pin
is VRTPH > 5.0 V, the IC remains in the preheating mode.
Final Data Sheet
32
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
2.8.1.1
Skip the Preheating Phase – Set RTPH Pin to GND
Figure 27 shows a standard start-up with a preheating time set via resistor at the RTPH pin 11 to GND (e.g. 8.2 kΩ
– this is equal to a preheating phase of approx. 820 ms). The preheating phase can be skipped by setting the
RTPH pin 11 directly to GND. In this case, ignition takes place directly after the soft start phase (see Figure 28).
VCC
Standard Start UP with Pre Heating
17.5 V
16.0 V
Chip Supply Voltage
14.0 V
10.6 V
UVLO
VRTPH
Time
Start Up
Hysteresis
5.0 V
Duration of Pre Heating
is set by Resistor only
2.5 V
Time
VLSGD
10.0 V
Time
VLamp
PRE HEATING
Time
t = 820 ms when using
R RTPH = 8.2kOhm
Figure 27
Start-Up WITH Preheating
Start UP without Pre Heating
VCC
17.5 V
16.0 V
Chip Supply Voltage
14.0 V
10.6 V
VRTPH
UVLO
Time
Start Up
Hysteresis
5.0 V
2.5 V
Set RTPH Resistor to GND
VLSGD
Time
10.0 V
Time
VLamp
INGNITION directly
Time
Figure 28
Start-Up WITHOUT Preheating
Final Data Sheet
33
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
2.8.1.2
IC Remains in Preheating Phase
This feature gives the customer the flexibility to align the preheating frequency to the filament power in the
preheating phase. Figure 29 shows a standard start-up with the set preheating time of, for example, 820 ms with
an 8.2 kΩ resistor at the RTPH pin 11. To force the IC to remain in preheating, the voltage level at the RTPH pin 11
has to be set to 5.0 V. The duration of this 5.0 V signal defines the time of the preheating (see IPreHeat in Figure 30).
VCC
17.5 V
16.0 V
Chip Supply Voltage
14.0 V
10.6 V
Time
Start Up
VRTPH UVLO Hysteresis
5.0 V
Duration is set by
Resistor only
2.5 V
Time
IPreHeat
Preheating
Time
t = 820 ms when using
RRTPH = 8.2kOhm
VLamp
IGNITION
Time
Figure 29
Start-Up WITH Preheating
VCC
17.5 V
16.0 V
Chip Supply Voltage
14.0 V
10.6 V
Time
Start Up
VRTPH UVLO Hysteresis
5.0 V
2.5 V
Set by external 5.0V Signal
Time
IPreHeat
IC remains in Preheating
Time
VLamp
NO Ignition
Time
Figure 30
Start-Up WITHOUT Preheating
Final Data Sheet
34
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
2.8.2
Deactivation of the Filament Detection
In order to deactivate the filament detection of the low or high side filament, set the RES pin 13 or the LVS pin to
GND. In this case, the IC starts up in normal operation without checking the filaments – e.g. when using an
equivalent lamp resistive load instead of a load.
VCC
17.5 V
16.0 V
Chip Supply Voltage
14.0 V
10.6 V
VRES
UVLO
Time
Start Up
Hysteresis
5.0 V
1.6 V
1.3 V
RES PIN set to GND
VLSGD
Time
10V
Time
VLamp
Time
Figure 31
Deactivation via RES PIN
VCC
17.5 V
16.0 V
Chip Supply Voltage
14.0 V
10.6 V
VRES
UVLO
Time
Start Up
Hysteresis
5.0 V
1.6 V
1.3 V
LVS PIN set to GND
Time
VLSGD
10V
Time
VLamp
Time
Figure 32
Deactivation via LVS PIN
Figure 31 shows the deactivation of the low and high side filament via set the RES pin 13 to GND. Figure 32
shows the deactivation of the high side filament detection via set the LVS pin to GND.
Note: An unused LVS pin has to be set to GND.
Final Data Sheet
35
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Functional Description
2.8.3
Built-in Customer Test Mode (Clock Acceleration)
The built-in customer test mode, supported by this IC, saves testing time for customers in terms of ballast end test.
In this mode, the IC accelerates the internal clock in order to reduce the time of the 4 different procedures by the
following factors (see Table 2).
Table 2
Specified Acceleration Factors
Phase
Duration for Test [ms]
Preheating
Acceleration Factor
Nominal Duration [ms]
625
4
2500 (max)
Time Out Ignition
118.5
2
237
Pre Run Mode
41.7
15
625
EOL2
41.7
60
2500
2.8.3.1
Enabling of the Clock Acceleration
The clock acceleration (Built-in Customer Test Mode) is activated when the chip supply voltage exceeds VCC
> 14.0 V and the voltages at the run and preheating frequency pins are set to VRFRUN = VRFPH = 5.0 V (± 5 %) –
see Figure 33. A RES pin voltage of VRES > 3.5 V up to 5.0 V (± 5 %) prevents a power-up of the IC, the IC remains
in a mode before powering up as long as the voltage at the RES pin is VRES > 3.5 V up to 5.0 V (± 5 %) – no powerup.
Note: After the activation of the clock acceleration mode, the voltage level of 5.0 V at the run and preheating
frequency pins (VRFRUN = VRFPH) can be released.
2.8.3.2
Starting the Chip with Accelerated Clock
In order to start the IC with an accelerated clock, set the voltage at the RES pin to GND (VRES = 0 V), see
Figure 33. The IC powers up the system and starts working with an accelerated clock. The duration of the different
modes are accelerated by the factors shown in Table 2.
IC Powers UP
Filament
Detection
IC Remains
in Power UP
Propagation Accelerated
Pre Heating
Delay
by Factor 4
VCC
Accelerated
Ign. Time OUT
by Factor 2
Accelerated
Pre RUN
by Factor 15
Accelerated
EOL2
by Factor 60
in Run Mode
V CCNom
14.0 V
10.6 V
Enabling of
Clock
Acceleration
Time
VRFRUN
5.0 V
2.5 V
Time
VRFPH
5.0 V
2.5 V
Starting the Chip with
an accelerated Clock
Time
VRES
3.5 V
Time
Figure 33
Clock Acceleration (Built in Customer Test Mode)
Final Data Sheet
36
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
State Diagram
3
State Diagram
3.1
Features during Different Operating Modes
Mains Switch turned on; 0V < Vcc < 10.6V; I_VCC < 130µA; I_RES= 0µA
10.6V < Vcc < 14.0V; I_VCC < 160µA; I_RES= 21.3µA
10.6V < Vcc < 17.5V;
I_RES= 21.3µA; f= F_RUN
Vcc > 14.0V & Filament detected; 12,5%< VBUS <105% => Start
after 130µs
F_START = 135kHz as long as VBUS < 95%
10.6V < Vcc < 17.5V
VBUS > 95%
F_START > f > F_PH
Typ. 60ms Typ. 35ms 0...80ms
UVLO
Monitoring Start-up
10ms
Softstart
BUS Overvoltage > 109% U enabled PFC enabled PFC
10.6V < Vcc < 17.5V
f= F_PH
10.6V < Vcc < 17.5V
f= F_RUN
10.6V < Vcc < 17.5V
F_PH > f > F_RUN
0...2500ms
Preheating
40...237ms
Ignition
enabled PFC
enabled PFC
625ms
Pre-Run
enabled PFC
Run
enabled PFC 5µs
enabled Inv 625 ms
BUS Overvoltage > 105%
A enabled 130µs
BUS Undervoltage < 95%
A
BUS Undervoltage < 75%
U
BUS Open Loop < 12,5%
U enabled PFC enabled PFC
Overcurrent PFC
N
Overcurrent Inverter
F enabled 1,6V enabled 1,6V
Capacitive Load 2
F
enabled 620µs
EOL 1, Overload
F
enabled 620µs
EOL 2, Rectifier Effect
F
enabled 2,5s
Capacitive Load 1
F
enabled 2,5s
A
N
U
F
= Auto Restart
= No Fault
= Undervoltage
= Fault, a single Restart
Figure 34
enabled
enabled 84µs
enabled
enabled
enabled PFC
enabled PFC
enabled
enabled
enabled 0,8V
enabled 1,6V
enabled PFC 5µs
enabled PFC enabled Inv 625 ms
enabled 200 ns
enabled
Threshold 1.0V
enabled 1,6V enabled 500ns
Threshold 0.8V
Fault: 10.6V < Vcc < 17.5V; I_VCC < 170µA; I_RES= 21.3µA
disabled by Lamp Removal or UVLO
F= A single Restart is possible after delay of 200ms by internal Timer
Minimum
Duration
of Effect
Monitoring Features during Different Operating Modes
Final Data Sheet
37
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
State Diagram
3.2
Operating Flow of the Start-Up Procedure into Run Mode
Vcc < 10.6V
UVLO
Vcc < 10.6V
Icc < 130µA
Vcc > 10.6V
Monitoring
Vcc > 10.6V
Icc < 160µA
Vcc > Vccon(14.0V)
& Filament detected
V BUS < 12,5%
or VBUS > 105%
Power-up
See
Timing and Handling of
Fault Conditions
Gate Drives off
14.1V < Vcc
Icc approx 6.0mA
after 130µs
& VBUS > 12,5%
& VBUS< 105%
Start-up
Inverter Gates on
PFC Gate on
17.5V> Vcc >10.6V
f_Inv = f_START
See
Protection
Functions
VBUS > 95%
within 80ms
Softstart
Fault
17.5V> Vcc >10.6V
Icc < 170µA
Gate Drives off
17.5V> Vcc >10.6V
f_START=> f_PH
after 10ms
after 10ms
& Flag Skip Preheat
& Flag Skip Preheat = Set
= Reset
// Reset Flag
Skip Preheat
Preheat
& Counter Skip PH // 17.5V> Vcc >10.6V
f = f_PH
after t_PH= 0...2500ms
Time set by R_TPH
Ignition*
Timeout 237ms
17.5V> Vcc >10.6V
f_PH => f_RUN
f_Inv= f_RUN within
t_IGN= 40...237ms
Pre-Run
17,5V> Vcc >10.6V
f = f_RUN
Reduced Monitoring
after
t_PRERUN= 625ms
Run
* NOTE:
Ignition will reset the
Flag Skip Preheating
Figure 35
17.5V> Vcc >10.6V
f = f_RUN
Complete Monitoring
Operating Flow during Start-Up Procedure
Final Data Sheet
38
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
State Diagram
3.3
Auto Restart and Latched Fault Condition Mode
Fault A
Fault U
Fault F
BUS Voltage
Fault, single Restart
Auto Restart
BUS Undervoltage
(VBUS < 75%
during Run Mode
for t > 84µs);
BUS Overvoltage
(VBUS > 109%
for t > 625ms);
Open Filament LS;
Inverter Overcurrent;
Capacitive Load 1;
Capacitive Load 2;
Timeout Ignition;
EOL 1 (Overload);
EOL 2 (Rectifier Effect);
Surge;
Time OUT Start Up
(VBUS < 95% for t >
80 ms)
Increment
Fault Counter
NOTE
to Set Flag Skip Preheat:
When using external Vcc
Supply, no reset of Set Flag
Skip Preheat. 1st Restart
without Preheating while
Vcc > UVLO. When LVS
deactivated or not from Line.
INVERTER and PFC Gate OFF
Only at Inverter Over current PFC Gate
OFF appr. 150µs Delayed
Power down Icc < 160µA
Wait 200ms
Delay Timer A
Fault Counter
<2
Set Flag
Skip Preheat
Gate drives off
Power down
Icc < 160µA
Wait 100ms
Delay Timer A
Increment
Counter Skip PH
Y
N
Reset
Fault Counter
Y
N
Wait for
Lamp Removal
Start
Start-up
Gate drives off
IC remains
in active mode
Lamp removed
for min 100ms
Inverter Gates on
PFC Gate on
17.5V> Vcc >10.6V
f_Inv = f_START
Wait for
Lamp inserted
Lamp
inserted?
N
N
t > 80ms?
from Power-Up
Y
Fault A
Timeout 80ms
Start-up
N
Lamp inserted
for min 100ms
NOTE
For external Vcc
Supply, set Vcc
below UVLO.
Lamp inserted &
ILVSSink > 12µA typ.
N
Y
Y
Wait for
UVLO
VBUS > 95%?
Y
End
Start-up
Vcc > 14.0V?
Reset
Flag Skip Preheat
& Counter Skip PH
N
Y
Note:
Fault Counter reset
after 40s in Run Mode
Reset of Flag Skip
Preheat after Ignition
Power-up
Gate Drives off
Figure 36
Counter
Skip Preheat
>7?
Vcc < 10.6V?
N
Y
UVLO
Reset all Latches
Operating Process during Start-Up Mode and Handling of Fault Conditions
Final Data Sheet
39
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Protection Functions Matrix
Operating Mode Detection Active
S
1μs
X
Supply voltage Vcc < 10.6 V
after power-up
Below UVLO
threshold
S
5μs
X
Current into LVS pin < 12μA Open
(typ.) before power-up
filament HS
S
100μs
X
Prevents power-up
Voltage at RES pin > 1.6 V
before power-up
Open
filament LS
S
100μs
X
Prevents power-up
Voltage at RES pin > 3.2 V
Open
filament LS
F
620μs
Bus voltage < 12.5% of rated Open loop
level 10 μs after power-up
detection
S
1μs
Bus voltage < 12.5 %
of rated level
Open loop
detection
N
1μs
Bus voltage < 12.5%
of rated level
Shut-down
option
U
Bus voltage < 75%
Underof rated level
voltage
add. shut down delay 120μs
Bus voltage < 95% of rated
level during start-up
Run Mode
Below startup threshold
Softstart 10ms
Monitoring
Supply voltage Vcc < 14.0 V
before power-up
Power-up 130 μs
Minimum Duration
of effect
Consequence
Type of fault
Characteristics of Fault
Name of Fault
Description of Fault
Pre-Run Mode 625ms
Protection Functions Matrix
Ignition Mode 40 – 237ms
Table 3
Preheat Mode 0 – 2500ms
Protection Functions Matrix
Start-up until VBUS > 95%
4
Prevents power-up
X
X
X
X
X
X
X
X
X
Power-down, reset
failure latch
Power down, latched
fault mode, 1 restart
Keep Gate drives off, restart after Vcc hysteresis
X
Stops PFC FET until
VBUS > 12.5%
625ms
X
Power down, restart
when VBUS> 12.5%
U
84μs
X
Power down, 100ms
delay, restart, skip preheating max 7 times
A
80ms
Bus voltage > 105% of rated Overlevel 10μs after power-up
voltage
S
5μs
Bus voltage > 109% of rated PFC
level in active operation
overvoltage
N
5μs
Bus voltage > 109% of rated Inverter
level in active operation
overvoltage
U
+/- peak level of lamp voltage EOL 1
at pin LVS above threshold overvoltage
DC level of lamp voltage
above +/- threshold
Timeout max
start-up time
X
X
X
X
X
X
Power down, 200ms
delay, restart
X
Keep Gate drives off, restart after Vcc hysteresis
X
Stops PFC FET until
VBUS< 105%
625ms
X
Power down, restart
when VBUS<105%
F
620μs
X
Power down, latched
fault mode, 1 restart
EOL 2
rect. effect
F
2500ms
X
Power down, latched
fault mode, 1 restart
Capacitive load 1
Cap load 1
idling
F
2500ms
X
Power down, latched
fault mode, 1 restart
Capacitive load 2,
operation below resonance
Cap. load 2
overload
F
620μs
X
Power down, latched
fault mode, 1 restart
Final Data Sheet
X
40
X
X
X
X
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Protection Functions Matrix
Protection Functions Matrix (cont’d)
Voltage at LSCS pin >0.8V
Inverter
current lim
N
200ns
Voltage at LSCS pin >0.8V
Inverter
overcurrent
F
500ns
Voltage at LSCS pin >1.6V
Inverter
overcurrent
F
500ns
Inverter overcurrent
& VBUS > 109% (Surge)
Surge
A
500ns
X
X
X
X
X
Power down, latched
fault mode, 1 restart
X
X
X
X
X
X
Stops on-time of PFC
FET immediately
Activates ignition control
X
X
Consequence
Run Mode
200ns
Pre-Run Mode 625ms
N
Ignition Mode 40 – 237ms
Voltage at PFCCS pin >1.0V PFC
overcurrent
Preheat Mode 0 – 2500ms
237ms
Softstart 10ms
F
Start-up until VBUS > 95%
Minimum Duration
of effect
Timeout
ignition
Run frequency cannot be
achieved
Operating Mode Detection Active
Power-up 130 μs
Type of fault
Characteristics of Fault
Name of Fault
Description of Fault
Monitoring
Table 3
X
X
Power down, latched
fault mode, 1 restart
Power down, latched
fault mode, 1 restart
X
Power-down, restart
when VBUS < 109 %
After jump into latched fault mode F wait
200ms A single restart attempt after delay of internal timer
Reset of failure latch in run mode after
40s
Reset of failure latch by UVLO or 40 s in run mode
S = Start-up condition, N = No fault, A = Auto restart , U = Undervoltage
F = Fault with a single restart; a second F leads to a latched fault
Note: All values @ typical 50 Hz mains frequency
Final Data Sheet
41
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Electrical Characteristics
5
Electrical Characteristics
All voltages without the high side signals are measured with respect to ground (pin 4). The high side voltages are
measured with respect to pin 17. The voltage levels are valid if other ratings are not violated.
5.1
Absolute Maximum Ratings
Absolute maximum ratings are defined as ratings, which when exceeded may lead to destruction of the integrated
circuit. For the same reason, ensure that any capacitor to be connected to pin 3 (VCC) or pin 15 (HSVCC) is
discharged before assembling the application circuit.
Parameter
Symbol
Limit Values
min.
max.
Unit
Remarks
LSCS Voltage
VLSCS
–5
6
V
LSCS Current
ILSCS
–3
3
mA
LSGD Voltage
VLSGD
–0.3
Vcc+0.3
V
LSGD Peak Source Current
ILSGDsomax
–75
5
mA
< 500 ns
LSGD Peak Sink Current
ILSGDsimax
–50
400
mA
< 100 ns
VCC Voltage
VVCC
–0.3
18.0
V
VCC Zener Clamp Current
IVCCzener
–5
5
mA
PFCGD Voltage
VPFCGD
–0.3
Vcc+0.3
V
PFCGD Peak Source Current
IPFCGDsomax
–150
5
mA
< 500 ns
PFCGD Peak Sink Current
IPFCGDsimax
–100
700
mA
< 100 ns
PFCCS Voltage
VPFCCS
–5
6
V
PFCCS Current
IPFCCS
–3
3
mA
PFCZCD Voltage
VPFCZCD
–3
6
V
PFCZCD Current
IPFCZCD
–5
5
mA
PFCVS Voltage
VPFCVS
–0.3
5.3
V
RFRUN Voltage
VRFRUN
–0.3
5.3
V
RFPH Voltage
VRFPH
–0.3
5.3
V
RTPH Voltage
VRTPH
–0.3
5.3
V
RES Voltage
VRES
–0.3
5.3
V
LVS Voltage
VLVS
–6
7
V
LVS Current1
ILVS_1
–1
1
mA
IC in Power Down Mode
LVS Current2
ILVS_2
–3
3
mA
IC in active Mode
HSGND Voltage
VHSGND
–650
650
V
HSGND Voltage Transient
dVHSGND/dt
–40
40
V/ns
HSVCC Voltage
VHSVCC
–0.3
18.0
V
Referring to HSGND
HSGD Voltage
VHSGD
–0.3
VHSVCC+
0.3
V
Internally clamped to 11V
HSGD Peak Source Current
IHSGDsomax
–75
0
mA
< 500 ns
HSGD Peak Sink Current
IHSGDsimax
0
400
mA
< 100 ns
Junction Temperature
TJ
–25
150
°C
Final Data Sheet
42
Internally clamped to 11 V
IC in Power Down Mode
Referring to GND1)
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Electrical Characteristics
Parameter
Symbol
Limit Values
Unit
min.
max.
–55
150
°C
Remarks
Storage Temperature
TS
Maximum Power Dissipation
PTOT
–
1
W
PG_DSO-16
Tamb=25°C
Thermal Resistance (Both Chips) RthJA
Junction-Ambient
–
1252)
K/W
PG_DSO-16
Soldering Temperature Wave
–
260
°C
Wave Soldering3)
Soldering Temperature Reflow
–
4)
°C
Reflow Soldering
ESD Capability HBM
VESD_HBM
–
2
kV
Human Body Model5)
ESD Capability CDM
VESD_CDM
–
1
kV
Charged Device Model6)
Rated Bus Voltage (95%)
VPFCVS95
2.33
2.43
V
1)
2)
3)
4)
5)
6)
Limitation due to voltage capability in end test
@Ta = 85°C & PCB area >30mmx20mm
According to JESD22A111
According to J-STD-020D
According to EIA/JESD22-A114-B
According to JESD22-C101
Final Data Sheet
43
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Electrical Characteristics
5.2
Operating Range
The IC operates as described in the functional description once the values listed here lie within the operating
range.
Parameter
Symbol
Limit Values
min.
max.
Unit
Remarks
HSVCC Supply Voltage
VHSVCC
VHSVCCOff
17.5
V
Referring to HSGND
HSGND Voltage
VHSGND
–650
650
V
Referring to GND1)
VCC Voltage @ 25°C
VVCC
VVCCOff
17.5
V
TJ = 25°C
VCC Voltage @ 125°C
VVCC
VVCCOff
18.0
V
TJ = 125°C
LSCS Voltage Range
VLSCS
–4
5
V
In active mode
PFCVS Voltage Range
VPFCVS
0
4
V
PFCCS Voltage Range
VPFCCS
–4
5
V
In active mode
PFZCD Current Range
IPFCZCD
–3
3
mA
In active mode
LVS Voltage Range
VLVS
–6
LVS Current Range
ILVS
LVS Current Range
2)
6
V
3)
210
μA
IC Power Down Mode
ILVS
–2.5
2.5
mA
IC active mode
RFPH Frequency
FRFPHrange
FRUN
150
kHz
RFPH Source Current Range
IRFPH
–500
0
μA
RTPH Voltage Range
VRTPH
0
2.5
V
Junction Temperature
Tj
–25
125
°C
Adjustable Preheating Freq.
FRFPH
FRFRUN
150
kHz
Range set by RFPH
Adjustable Run Frequency
FRFRUN
20
120
kHz
Range set by RFRUN
Adjustable Preheating Time
tRTPH
0
2500
ms
Range set by RTPH
Set Resistor for Run Feq.
RRFRUN
4
25
kΩ
Set Resistor for Preheat Feq.
RRFPH
4
–
kΩ
Set Resistor for Preheat Time
RRTPH
0
25
kΩ
Mains Frequency
fMains
45
65
Hz
@ VRFPH = 2.5 V
RRFRUN parallel to RRFPH
NOTCH Filter Operation
1) Limitation due to creeping distance between the HS&LS Pins
2) Limited by Maximum of Current Range at LVS
3) Limited by Minimum of Voltage Range at LVS
Final Data Sheet
44
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Electrical Characteristics
5.3
Characteristics
5.3.1
Power Supply Section
The electrical characteristics involve the spread of values guaranteed within the specified supply voltage and
junction temperature range TJ from –25 °C to +125 °C. Typical values represent the median values, which are
related to 25 °C. Unless otherwise stated, a supply voltage of 15 V and VHSVCC = 15 V is assumed and the IC
operates in active mode. Furthermore, all voltages refer to GND if not otherwise stated.
Parameter
Symbol
Limit Values
min.
typ.
max.
Unit
Test Conditions
VCC Quiescent Current1
IVCCqu1
–
90
130
μA
VVCC = VVCCOff – 0.5V
VCC Quiescent Current2
IVCCqu2
–
120
160
μA
VVCC = VVCCOn – 0.5V
VCC Supply Current
IVCCSupply
–
4.2
6.0
mA
VPFCVS > 2.725V
VCC Supply Current in Latched
Fault Mode
IVCCLatch
–
110
170
μA
VRES = 5V
LSVCC Turn-On Threshold
LSVCC Turn-Off Threshold
LSVCC Turn-On/Off Hyst.
VVCCOn
VVCCOff
VVCCHys
13.5
10.0
3.2
14.0
10.6
3.6
14.5
11.0
4.0
V
V
V
Hysteresis
VCC Zener Clamp Voltage
VVCCClamp
15.5
16.3
16.9
V
IVCC = 2mA/VRES = 5V
VCC Zener Clamp Current
IVCCZener
2.5
–
5
mA
VVCC = 17.5V/VRES = 5V
High Side Leakage Current
IHSGNDleak
1)
–
0.01
2
μA
VHSGND = 650V, VGND=0V
IHSVCCqu1
2)
–
190
280
μA
VHSVCC = VHSVCCOn – 0.5V
IHSVCCqu2
2)
0.3
0.65
1.2
mA
VHSVCC > VHSVCCOn
HSVCC Turn-On Threshold
HSVCC Turn-Off Threshold
HSVCC Turn-On/Off Hyst.
VHSVCCOn2)
VHSVCCOff2)
VHSVCCHy2)
9.8
8.1
1.4
10.4
8.6
1.7
11.0
9.3
2.0
V
V
V
Low Side Ground
GND
HSVCC Quiescent Current
HSVCC Quiescent Current
1)
Hysteresis
1) With inactive gate
2) Referring to High Side Ground (HSGND)
Final Data Sheet
45
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Electrical Characteristics
5.3.2
PFC Section
5.3.2.1
PFC Current Sense (PFCCS)
Parameter
Symbol
Limit Values
Unit
min.
typ.
max.
0.95
1.0
1.05
V
200
260
ns
Test Conditions
Turn – Off Threshold
VPFCCSOff
Over Current Blanking +
Propagation Delay1)
tPFCCSOff
Leading Edge Blanking
tBlanking
180
250
310
ns
Pulse width when VPFCCS > 1.0 V
PFCCS Bias Current
IPFCCSBias
–0.5
–
0.5
μA
VPFCCS = 1.5V
140
1) Propagation delay = 50 ns
5.3.2.2
PFC Zero Current Detection (PFCZCD)
Parameter
Symbol
Limit Values
Unit
Test Conditions
min.
typ.
max.
VPFCZCDUp
1.4
1.5
1.6
V
VPFCZCDLow
0.4
0.5
0.6
V
Zero Crossing Hysteresis
VPFCZCDHys
–
1.0
–
V
Clamping of pos. Voltages
VPFCZCDpclp
4.1
4.6
5.1
V
IPFCZCDSink = 2mA
Clamping of neg. Voltages
VPFCZCDnclp
–1.7
–1.4
–1.0
V
IPFCZCDSource = –2mA
PFCZCD Bias Current
IPFCZCDBias
–0.5
–
5.0
μA
VPFCZCD = 1.5V
PFCZCD Bias Current
IPFCZCDBias
–0.5
–
0.5
μA
VPFCZCD = 0.5V
PFCZCD Ringing Su. Time
tRingsup
350
500
650
ns
Limit Value for ON Time
Extension
∆t x IZCD
500
700
900
pAxs
1)
2)
Zero Crossing upper Thr.
Zero Crossing lower Thr.
3)
1) Turn OFF threshold
2) Turn ON threshold
3) Ringing Suppression Time
Final Data Sheet
46
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Electrical Characteristics
5.3.2.3
PFC Bus Voltage Sense (PFCVS)
Parameter
Symbol
Limit Values
min.
typ.
max.
Unit
Trimmed Reference Voltage
VPFCVSRef
2.47
2.50
2.53
V
Overvoltage turn Off (109%)
VPFCVSRUp
2.68
2.73
2.78
V
Overvoltage turn On (105%)
VPFCVSLow
2.57
2.63
2.68
V
Overvoltage Hysteresis
VPFCVSHys
70
100
130
mV
Under voltage (75%)
VPFCVSUV
1.835 1.88 1.915
V
Under voltage (12.5%)
VPFCVSUV
0.237 0.31 0.387
V
Rated Bus Voltage (95%)
VPFCVS95
2.325 2.38 2.425
V
PFCVS Bias Current
IPFCVSBias
–1.0
μA
5.3.2.4
–
1.0
Test Conditions
± 1.2 %
4 % rated bus voltage
VPFCVS = 2.5V
PFC PWM Generation
Parameter
Symbol
Limit Values
Unit
Test Conditions
min.
typ.
max.
tPFCON_initial
–
4.0
–
μs
VPFCZCD = 0V
Max. ON – Time
tPFCON_max
18.0
24.0
28.0
μs
0.45V < VPFCVS < 2.45V
Switch Threshold from CritCM
into DCM
tPFCON_min
160
270
370
ns
Repetition Time1)
tPFCRep
47
52
57
μs
Off Time
tPFCOff
42
47
52
μs
1)
2)
Initial ON – Time
VPFCZCD = 0V
1) When missing Zero Crossing Signal
2) At the maxima of the AC Line Input Voltage
Final Data Sheet
47
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Electrical Characteristics
5.3.2.5
PFC gate Drive (PFCGD)
Parameter
PFCGD Low Voltage
PFCGD High Voltage
Symbol
VPFCGDLow
VPFCGDHigh
Limit Values
Unit
Test Conditions
min.
typ.
max.
0.4
0.7
0.9
V
IPFCGD = 5mA
0.4
0.75
1.1
V
IPFCGD = 20mA
–0.2
0.3
0.6
V
IPFCGD = -20mA
10.0
11.0
11.6
V
IPFCGD = -20mA
9.0
–
–
V
IPFCGD = -1mA / VVCC1)
8.5
–
–
V
IPFCGD = -5mA / VVCC1)
PFCGD active Shut Down
VPFCGASD
0.4
0.75
1.1
V
IPFCGD = 20mA VVCC=5V
PFCGD UVLO Shut Down
VPFCGDuvlo
0.3
1.0
1.5
V
PFCGD Peak Source Current
IPFCGDSouce
–
–100
–
mA
IPFCGD
2) 3)
= 5mA VVCC=2V
+
2) 3)
PFCGD Peak Sink Current
IPFCGDSink
–
500
–
mA
+
PFCGD Voltage during sink
Current
VPFCGDHigh
11.0
11.7
12.3
V
IPFCGDSinkH = 3mA
PFC Rise Time
tPFCGDRise
100
245
405
ns
2V > VLSGD > 8V 2)
PFC Fall Time
tPFCGDFall
20
45
70
ns
8V > VLSGD > 2V 2)
1) VVCC = VVCCOff + 0.3 V
2) RLoad = 4Ω and CLoad = 3.3 nF
3) The parameter is not subject to a production test – verified by design / characterization
Final Data Sheet
48
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Electrical Characteristics
5.3.3
Inverter Section
5.3.3.1
Low Side Current Sense (LSCS)
Parameter
Symbol
Limit Values
min.
typ.
max.
Unit
Test Conditions
Overcurrent Shut Down Volt.
VLSCSOvC1
1.5
1.6
1.7
V
1)
Overcurrent Shut Down Volt.
VLSCSOvC2
0.75
0.8
0.85
V
2)
Duration of Overcurrent
tLSCSOvC
450
600
700
ns
Capacitive Mode Det. Level 1
VLSCSCap1
30
50
73
mV
Capacitive Mode Duration 1
tLSCSCap1
–
280
–
ns
Capacitive Mode Det. Level 2
VLSCSCap2
1.8
2.0
2.2
V
During Run Mode
4)
During Run Mode
3)
Capacitive Mode Duration 2
tLSCSCap2
–
50
–
ns
Capacitive Mode Det. Level 3
VLSCSCap3
–70
-50
-27
mV
Capacitive Mode Duration 3
tLSCSCap3
–
280
–
ns
5)
LSCS Bias Current
ILSCSBias
–1.0
–
1.0
μA
@ VLSCS = 1.5V
1)
2)
3)
4)
5)
Overcurrent Voltage Threshold active during: Start Up, Soft start, Ignition and pre-run Mode
Overcurrent Voltage Threshold active during: Preheating and Run Mode
During 2nd 50% Duty Cycle of LSGD in Run Mode
Active during Turn ON of the HSGD in Run Mode
Active before Turn ON of the HSGD in Run Mode
Final Data Sheet
49
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Electrical Characteristics
5.3.3.2
Low Side Gate Drive (LSGD)
Parameter
Symbol
LSGD Low Voltage
VLSGDLow
LSGD High Voltage
VLSGDHigh
Limit Values
Unit
Test Conditions
min.
typ.
max.
0.4
0.7
1.0
V
ILSGD = 5mA1)
0.4
0.8
1.2
V
ILSGD = 20mA1)
–0.3
0.2
0.5
V
ILSGD = - 20mA (Source)
10.0
10.8
11.6
V
2)
9.0
–
–
V
3)
8.5
–
–
V
4)
LSGD active Shut Down
VLSGDASD
0.4
0.75
1.1
V
VCC=5V / ILSGD = 20mA1)
LSGD UVLO Shut Down
VLSGDUVLO
0.3
1.0
1.5
V
VCC=2V / ILSGD = 5mA1)
LSGD Peak Source Current
ILSGDSource
–
–50
–
mA
5) 6)
5) 6)
LSGD Peak Sink Current
+
ILSGDSink
–
300
–
mA
VLSGDHigh
–
11.7
–
V
ILSGDsinkH = 3mA
LSGD Rise Time
tLSGDRise
100
245
405
ns
2V < VLSGD < 8V5)
LSGD Fall Time
tLSGDFall
20
35
60
ns
8V > VLSGD > 2V5)
LSGD Voltage during
1)
2)
3)
4)
5)
6)
1)
+
Sink Current
ILSGD = - 20mA Source Current
VCCOFF + 0.3V and ILSGD = - 1mA Source Current
VCCOFF + 0.3V and ILSGD = - 5mA Source Current
Load: RLoad = 10Ω and CLoad = 1nF
The parameter is not subject to a production test – verified by design / characterization
5.3.3.3
Inverter Control Run (RFRUN)
Parameter
Symbol
Limit Values
Unit
min.
typ.
max.
Test Conditions
Fixed Start – Up Frequency
FStartUp
121.5
135
148.5
kHz
Duration of Soft Start
tSoftStart
9
11
13.5
ms
RFRUN Voltage in Run Mode
VRFRUN
–
2.5
–
V
Run Frequency
FRFRUN
49
50
51
kHz
RRFRUN = 10kΩ
Adjustable Run Frequency
FRFRUN1
–
20
–
kHz
IRFRUN = – 100 μA
FRFRUN2
–
40
–
kHz
IRFRUN = – 200 μA
FRFRUN3
–
100
–
kHz
IRFRUN = – 500 μA
IRFRUNmax
–
μA
@ VRFRUN = 0V
RFRUN max. Current Range
–1000 – 650
1)
@ 100μA<IRFRUN<600μA
1) Shift Start Up Frequency to Preheating Frequency
Final Data Sheet
50
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Electrical Characteristics
5.3.3.4
Inverter Control Preheating (RFPH, RTPH)
Parameter
Symbol
Limit Values
Unit
min.
typ.
max.
Test Conditions
RFPH Voltage Preheating
VRFPH
–
2.5
–
V
VRFPH = 0V in Run Mode
Preheating Frequency
FRFPH1
97
100
103
kHz
RRFPH = RRFRUN = 10kΩ
RFPH max. Current Range
IRFPHmax
–
–1000 – 550
μA
@ VRFPH = 0V
Current for set Preh. Time
IRTPH
–
–100
–
μA
Preheating Time
tRTPH1
950
1000
1050
ms
RRTPH1 = 10kΩ
tRTPH2
50
100
150
ms
RRTPH2 = 1kΩ
tRTPH3
–
500
–
ms
RRTPH3 = 5kΩ
tRTPH4
–
2000
–
ms
RRTPH4 = 20kΩ
tRTPH5
–
2500
–
ms
RRTPH5 = 25kΩ
5.3.3.5
Restart after Lamp Removal (RES)
Parameter
High Side Filament In Det.
RES Current Source
Final Data Sheet
Symbol
Limit Values
Unit
Test Conditions
min.
typ.
max.
VRES1
1.55
1.60
1.65
V
VRES2
1.25
1.30
1.35
V
VRES3
–
3.2
–
V
Run Mode
UVLO, VCC < VCCON
IRES1
–53.2 –42.6 –32.0
μA
VRES = 1V ;LVS = 5μA
IRES2
–44.2 –35.4 –26.6
μA
VRES = 2V ;LVS = 5μA
IRES3
–26.6 –21.3 – 16.0
μA
VRES = 1V ;LVS = 30μA
IRES4
–22.1 –17.7 –13.3
μA
VRES = 2V ;LVS = 30μA
51
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Electrical Characteristics
5.3.3.6
Lamp Voltage Sense (LVS)
Parameter
Symbol
Source Current before Startup
ILVSSource
Limit Values
min.
typ.
max.
–5.0
–3.0
–2.0
Unit
Test Conditions
μA
VLVS = 0V
Enable Lamp Monitoring
VLVSEnable1
350
530
750
mV
1)
Sink Current for Lamp Det.
ILVSSink
8.0
12.0
18.0
μA
VLVS > VLVSClamp
Positive Clamping Voltage
VLVSClamp
–
6.5
–
V
@ ILVS = 300μA
AC EOLCurrent Threshold
ILVSSourceAC
190
210
230
μApp
ILVS > ILVSEOLpp EOL 1
Positive EOL Current Thr.
ILVSDCPos
34
42
50
μA
ILVS > ILVSDCPos EOL 2
Negative EOL Current Thr.
ILVSDCNeg
–50
–42
–34
μA
ILVS > ILVSDCNeg EOL 2
1) If VLVS < VLVSEnable1 monitoring is disabled
5.3.3.7
High Side Gate Drive (HSGD)
Parameter
HSGD Low Voltage
HSGD High Voltage
Symbol
VHSGDLow
VHSGDHigh
Limit Values
Unit
Test Conditions
min.
typ.
max.
0.02
0.05
0.1
V
IHSGD = 5mA (sink)
0.5
1.1
2.5
V
IHSGD = 100mA (sink)
–0.4
–0.2 –0.05
V
ILSGD = - 20mA (source)
9.7
10.5
11.2
V
VCCHS=15V
IHSGD = - 20mA (source)
7.8
–
–
V
VCCHSOFF + 0.3V
IHSGD = - 1mA (source)
VCCHS=5V
IHSGD = 20mA (sink)
HSGD active Shut Down
VHSGDASD
0.05
0.22
0.5
V
HSGD Peak Source Current
IHSGDSource
–
–50
–
mA
RLoad = 10Ω+CLoad = 1nF1)
HSGD Peak Sink Current
IHSGDSink
–
300
–
mA
RLoad = 10Ω+CLoad = 1nF1)
HSGD Rise Time
tHSGDRise
120
220
300
ns
2V < VLSGD < 8V
RLoad = 10Ω+CLoad = 1nF
HSGD Fall Time
tHSGDFall
20
35
70
ns
8V > VLSGD > 2V
RLoad = 10Ω+CLoad = 1nF
1) The parameter is not subject to a production test – verified by design / characterization
Final Data Sheet
52
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Electrical Characteristics
5.3.3.8
Timer Section
Delay Timer 1
tTIMER1
70
100
160
ms
For lamp detection
Delay Timer 2
tTIMER2
74
84
94
ms
For VBUS > 95%
Inverter Time
tInv
100
130
160
μs
Inverter Dead Time Max
tDeadMax
1.75
2.1
2.40 μs
Inverter Dead Time Min
tDeadMin
0.8
1.05
1.3
μs
∆ Inverter Dead Time Max
tDeadMax
–200
–
200
ns
∆ Inverter Dead Time Min
tDeadMin
–200
–
200
ns
Min. Duration of Ignition
tIgnition
34
40
48
ms
Max. Duration of Ignition
tNOIgnition
197
–
236
ms
Duration of Pre – Run
tPRERUN
565
625
685
ms
5.3.3.9
Built-In Customer Test Mode
Voltage at RTPH Pin
VRTPH
0
V
Voltage at RTPH Pin
VRTPH
5.0
V
Voltage at LVS
VLVS
0
V
Voltage at RES Pin
VRES
0
V
Voltage at RFPH Pin
VRFPH
5.0
Preheating time = 0 ms (skipped preheating)
1)
Disables Lamp Voltage Sense
Disable the Filament Detection
V
1)
V
1)
Voltage at RFRUN Pin
VRFRUN
5.0
Voltage at VCC Pin
VCC
> 14.0 V
Voltage at RES Pin
VRES
0
IC remains in Preheating
V
Built-in Customer Test Mode - Clock
Acceleration. Decreasing time for the following
procedures: Preheating by factor 4
Timeout ignition by factor 2
Pre-run by factor 15; EOL by 60
1) Tolerance for this voltage is ± 5%
Final Data Sheet
53
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Electrical Characteristics
5.3.4
Parameter limits for extended temperature range down to -40°C
For any other parameter which is not listed below, the -25°C limit is also valid for -40°C
Parameter
Symbol
Limit Values
min.
Junction Temperature
TJ
LSVCC Turn-On Threshold
VVCCOn
VCC Zener Clamp Voltage
IVCCZener
2.5
HSVCC Quiescent Current
IHSVCCqu2
HSVCC Turn-On Threshold
HSVCC Turn-Off Threshold
HSVCC Turn-On/Off Hyst.
VHSVCCOn
VHSVCCOff
VHSVCCHy
Over Current Blanking +
Propagation Delay
tPFCCSOff
Leading Edge Blanking
tBlanking
Clamping of pos. Voltages
Clamping of neg. Voltages
typ.
-40
Test Conditions
max.
150
°C
14.5
V
-
5.05
mA
VVCC = 17.5V/VRES = 5V
0.26
0.65
1.2
mA
VHSVCC > VHSVCCOn
9.8
8.08
1.4
10.4
8.6
1.7
11.0
9.3
2.03
V
V
V
200
262
ns
180
250
315
ns
Pulse width when VPFCCS > 1.0 V
VPFCZCDpclp
4.1
4.6
5.12
V
IPFCZCDSink = 2mA
VPFCZCDnclp
-1.69
-1.4
-1.0
V
IPFCZCDSource = -2mA
PFCZCD Ringing Suppress. Time tRingsup
350
500
660
ns
Limit Value for ON Time
Extension
∆t x IZCD
498
700
900
pAxs
Trimmed Reference Voltage
VPFCVSRef
2.468 2.50
2.53
V
Overvoltage turn Off (109%)
VPFCVSRUp
2.677 2.73
2.78
V
Overvoltage turn On (105%)
VPFCVSLow
2.567 2.63
2.68
V
Under voltage (75%)
VPFCVSUV
1.832 1.88 1.915
V
Rated Bus Voltage (95%)
VPFCVS95
2.320 2.38 2.425
V
Max. ON – Time
tPFCON_max
18.0
24.0
28.6
μs
Off Time
tPFCOff
42
47
52.5
μs
PFCGD Low Voltage
VPFCGDLow
0.4
0.7
0.92
V
IPFCGD = 5mA
0.4
0.75
1.12
V
IPFCGD = 20mA
-0.2
0.3
0.62
V
IPFCGD = -20mA
10.0
11.0
11.6
V
IPFCGD = -20mA
8.98
–
–
V
IPFCGD = -1mA / VVCC1)
8.47
–
–
V
IPFCGD = -5mA / VVCC1)
PFCGD High Voltage
VPFCGDHigh
13.48 14.0
Unit
140
Hysteresis
Hysteresis
± 1.2 %
0.45V < VPFCVS < 2.45V
PFCGD active Shut Down
VPFCGASD
0.4
0.75
1.12
V
IPFCGD = 20mA VVCC=5V
PFCGD UVLO Shut Down
VPFCGDuvlo
0.3
1.0
1.56
V
IPFCGD = 5mA VVCC=2V
PFC Rise Time
tPFCGDRise
100
245
450
ns
2V > VLSGD > 8V2)
PFC Fall Time
tPFCGDFall
20
45
72
ns
8V > VLSGD > 2V2)
LSGD Low Voltage
VLSGDLow
0.4
0.7
1.02
V
ILSGD = 5mA (sink)
0.4
0.8
1.22
V
ILSGD = 20mA (sink)
-0.3
0.2
0.53
V
ILSGD = -20mA (source)
Final Data Sheet
54
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Electrical Characteristics
Parameter
LSGD High Voltage
Symbol
VLSGDHigh
Limit Values
Unit
min.
typ.
max.
10.0
10.8
11.6
V
8.98
–
–
V
8.47
–
–
V
Test Conditions
LSGD active Shut Down
VLSGDASD
0.4
0.75
1.12
V
VCC=5V / ILSGD = 20mA (sink)
LSGD UVLO Shut Down
VLSGDUVLO
0.3
1.0
1.6
V
VCC=2V / ILSGD = 5mA (sink)
LSGD Rise Time
tLSGDRise
100
245
460
ns
2V < VLSGD < 8V3)
LSGD Fall Time
tLSGDFall
20
35
61
ns
8V > VLSGD > 2V
Fixed Start – Up Frequency
FStartUp
120
135
148.5
kHz
Duration of Soft Start
tSoftStart
9
11
13.56
ms
4)
Run Frequency
FRFRUN
49
50
51.07
kHz
RRFRUN = 10kΩ
RFRUN max. Current Range
IRFRUNmax
–
-1000 -612
μA
@ VRFRUN = 0V
RFPH max. Current Range
IRFPHmax
–
-1000 -512
μA
@ VRFPH = 0V
Preheating Time
tRTPH1
920
1000 1050
ms
RRTPH1 = 10kΩ
High Side Filament In Det.
VRES1
1.546 1.60
1.65
V
VRES2
1.247 1.30
1.35
V
IRES1
-53.2 -42.6 -30.5
μA
VRES = 1V ;LVS = 5μA
IRES2
-44.2 -35.4 -25.1
μA
VRES = 2V ;LVS = 5μA
IRES3
-26.6 -21.3
μA
VRES = 1V ;LVS = 30μA
IRES4
-22.1 -17.7 -12.3
μA
VRES = 2V ;LVS = 30μA
Source Current before Startup
ILVSSource
-5.0
-3.0
-1.9
μA
VLVS = 0V
Sink Current for Lamp Det.
ILVSSink
7.0
12.0
18.0
μA
VLVS > VLVSClamp
AC EOLCurrent Threshold
ILVSSourceAC
186
210
230
μApp
HSGD Low Voltage
VHSGDLow
0.018 0.05
0.1
V
IHSGD = 5mA (sink)
0.46
1.1
2.5
V
IHSGD = 100mA (sink)
-0.4
-0.2
-0.04
V
ILSGD = - 20mA (source)
0.5
V
VCCHS=5V
IHSGD = 20mA (sink)
70
ns
8V > VLSGD > 2V
RLoad = 10Ω+CLoad = 1nF
RES Current Source
-15
HSGD active Shut Down
VHSGDASD
HSGD Fall Time
tHSGDFall
19
35
Delay Timer 1
tTIMER1
70
100
Inverter Time
tInv
100
130
163
Inverter Dead Time Max
tDeadMax
1.75
2.1
2.50 μs
Inverter Dead Time Min
tDeadMin
0.8
1.05
1.33 μs
∆ Inverter Dead Time Max
tDeadMax
-240
–
200
ns
∆ Inverter Dead Time Min
tDeadMin
-230
–
200
ns
1)
2)
3)
4)
0.041 0.22
163.6 ms
UVLO, VCC < VCCON
ILVS > ILVSEOLpp EOL 1
For lamp detection
μs
VVCC = VVCCOff + 0.3 V
RLoad = 4Ω and CLoad = 3.3nF
Load: RLoad = 10Ω and CLoad = 1nF
Shift Start Up Frequency to Preheating Frequency
Final Data Sheet
55
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Application Example
6
Application Example
6.1
Schematic Ballast 54W T5 Single Lamp
Figure 37
Application Circuit of Ballast for Single Fluorescent Lamp Voltage Mode Preheating
Final Data Sheet
56
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Application Example
6.2
Bill of Material
Figure 38
Bill of Material
Final Data Sheet
57
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Application Example
Multi Lamp Ballast Topologies (Series Connection)
90 ...
270 VAC
LVS
PFCZCD
HSGD
Figure 39
LSGD
LSCS
RFPH
RFRUN
VCC
GND
PFCCS
HSGND
RES
PFCVS
HSVCC
RTPH
PFCGD
ICB2FL03G
6.3
Application Circuit of Ballast for two Fluorescent Lamps Voltage Mode Preheating
Final Data Sheet
58
V1.1, 2013-08-14
ICB2FL03G
Controller for Fluorescent Lamp Ballasts
Package Outline
7
Package Outline
7.1
Outline Dimensions of PG-DSO-16
Figure 40
Package Outline with Creepage Distance
Final Data Sheet
59
V1.1, 2013-08-14
w w w . i n f i n e o n . c o m
Published by Infineon Technologies AG
Similar pages