MSK MSK5500-15 Input voltage from vout dropout to 40v Datasheet

MIL-PRF-38534 AND 38535 CERTIFIED FACILITY
M.S.KENNEDY CORP.
ULTRA-HIGH
TEMPERATURE
REGULATOR
5500 -15
4707 Dey Road Liverpool, N.Y. 13088
(315) 701-6751
FEATURES:
Operational from -55°C to +232°C
Input Voltage from Vout + Dropout to 40V
Output Current up to 50mA @ 232°C
Soft-Start Feature
Stable Over a Wide Range of Load Capacitance
Low Standby Current Consumption (38uA @ 232°C)
Active-Low Shutdown Control
Surface Mount Package With Lead Forming
Contact MSK for Qualification Status
DESCRIPTION:
The MSK 5500-15 is a low power voltage regulator/reference capable of delivering 50mA of output current at 232°C.
Typical dropout is 0.450 volts with a 10mA load at 232°C. An external shutdown function is ideal for power supply
sequencing. This device also has short circuit protection that requires no external current sense resistor. The MSK 550015 is specifically designed for automotive, aeronautics and aerospace, and down-hole applications. The device is packaged
in a hermetically sealed 12 pin flatpack that is formed for surface mount applicatins.
EQUIVALENT SCHEMATIC
TYPICAL
APPLICATIONS
TYPICAL APPLICATIONS
PIN-OUT INFORMATION
Reliability-Critical, Automotive,
Aeronautics & Aerospace, Down-Hole
Precision Regulators/References,
A/D and D/A Converters, Current Sources
1
2
3
4
5
6
VIN
VIN
GND
GND
NC
NC
12
11
10
9
8
7
SHDN
VOUT
VOUT
VOUT
NC
NC
CASE=ISOLATED
1
8548-107 Rev. A 8/13
ABSOLUTE MAXIMUM RATINGS
VIN with Respect to GND
SHDN with Respect to GND
Storage Temperature Range
Case Operating Temperature Range
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
-0.5 to 50V
-0.5 to VIN+0.5V
-65°C to +250°C
-55°C to +232°C
○
○
5
○
○
○
○
○
○
○
ELECTRICAL SPECIFICATIONS
NOTES:
1
2
3
4
5
Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only.
Military grade devices ("H" suffix) shall be 100% tested to subgroups 1,2,3 and 4.
Subgroup 1,4 TA=TC=+25°C
2
TA=TC=+232°C
3
TA=TC=-55°C
Industrial grade devices shall be 100% tested at 25°C only.
Continuous operation at or above absolute maximum ratings may adversely effect the device performance and/or life cycle.
2
8548-107 Rev. A 8/13
APPLICATION NOTES
PIN FUNCTIONS
VIN - These pins provide the input power connection to the MSK
5500-15.
GND - These pins provide the input and output ground reference.
VOUT - These are the output pins for the device. All three pins
must be connected for proper operation.
SHDN - This pin is used to disable the output and is logic low.
INPUT AND OUTPUT BYPASSING
Proper input bypassing is required in order to filter out noise and
provide low AC impedance source. The MSK 5500-15 has an
internal 0.1uF ceramic capacitor connected between VIN and GND.
In most application the internal input capacitor will be sufficient
for proper operation. Additional input capacitance can be added
to maximize transient response and minimize power supply transients. For stability the MSK 5500-15 has an internal 0.2uF low
ESR capacitor connected between VOUT and GND. To improve
transient response additional capacitance up to 4.7uF can be
added if needed.
THERMAL LIMITING
The MSK 5500-15 has no internal thermal shutdown feature.
Operation above 232°C is possible at the expensive of reducing
product lifetime.
START UP OPTIONS
The MSK 5500-15 has been designed to provide a soft-start
with little to no overshoot. If slight overshoot is observed when
turning on into a light load adding output capacitance will eliminate the overshoot.
OVERCURRENT PROTECTION
The MSK 5500-15 has a short circuit protection feature it is,
however, not able to sink current. Doing so could damage the
regulator.
SHUTDOWN
The MSK 5500-15 has a shut-down feature that will set the
output of the regulator to high impedance. The feature helps reduce power consumption by 90% in power-critical applications.
A voltage lower then 0.6V on the SHDN pin will put the regulator into shut-down mode. A voltage of greater than 2.3V on the
SHDN pin will turn the regulator on.
3
8548-107 Rev. A 8/13
TYPICAL PERFORMANCE CURVES
4
8548-107 Rev. A 8/13
MECHANICAL SPECIFICATIONS
WEIGHT=3.5 GRAMS TYPICAL
ALL DIMENSIONS ARE ±0.010 INCHES UNLESS OTHERWISE LABELED.
ESD Triangle indicates pin 1.
ORDERING INFORMATION
PART NUMBER
SCREENING LEVEL
MSK5500-15
INDUSTRIAL
MSK5500-15H
MIL-PRF-38534 CLASS H
M.S. Kennedy Corp.
4707 Dey Road, Liverpool, New York 13088
Phone (315) 701-6751
FAX (315) 701-6752
www.mskennedy.com
The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make
changes to its products or specifications without notice, however, and assumes no liability for the use of its products.
Please visit our website for the most recent revision of this datasheet.
Contact MSK for MIL-PRF-38534 qualification status.
5
8548-107 Rev. A 8/13
Similar pages