TI1 LM158QML-SP Low power dual operational amplifier Datasheet

LM158QML
www.ti.com
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
LM158QML Low Power Dual Operational Amplifiers
Check for Samples: LM158QML
FEATURES
ADVANTAGES
•
•
•
•
1
2
•
•
•
•
•
•
•
•
•
Available with Radiation Specification
– High Dose Rate 100 krad(Si)
– ELDRS Free 100 krad(Si)
Internally Frequency Compensated for Unity
Gain
Large DC Voltage Gain: 100 dB
Wide Bandwidth (Unity Gain): 1 MH
z(Temperature Compensated)
Wide Power Supply Range:
– Single Supply: 3V to 32V
– Or Dual Supplies: ±1.5V to ±16V
Very Low Supply Current Drain (500 μA) −
Essentially Independent of Supply Voltage
Low Input Offset Voltage: 2 mV
Input Common-mode Voltage Range Includes
Ground
Differential Input Voltage Range Equal to the
Power Supply Voltage
Large Output Voltage Swing: 0V to V+ − 1.5V
UNIQUE CHARACTERISTICS
•
•
•
In the Linear Mode the Input Common-Mode
Voltage Range Includes Ground and the Output
Voltage can also Swing to Ground, even though
Operated from only a Single Power Supply
Voltage.
The Unity Gain Cross Frequency is Temperature
Compensated.
The Input Bias Current is also Temperature
Compensated.
•
•
Two Internally Compensated Op Amps
Eliminates Need for Dual Supplies
Allows Direct Sensing Near Gnd and VO also
Goes to Gnd
Compatible with all Forms of Logic
Power Drain Suitable for Battery Operation
DESCRIPTION
The LM158 series consists of two independent, high
gain, internally frequency compensated operational
amplifiers which were designed specifically to operate
from a single power supply over a wide range of
voltages. Operation from split power supplies is also
possible and the low power supply current drain is
independent of the magnitude of the power supply
voltage.
Application areas include transducer amplifiers, dc
gain blocks and all the conventional op amp circuits
which now can be more easily implemented in single
power supply systems. For example, the LM158
series can be directly operated off of the standard
+5V power supply voltage which is used in digital
systems and will easily provide the required interface
electronics without requiring the additional ±15V
power supplies.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2005–2013, Texas Instruments Incorporated
LM158QML
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
www.ti.com
Connection Diagrams
Figure 1. TO-99 Package
See Package Number LMC0008C
Top View
Top View
Figure 2. CDIP Package
See Package Number NAB0008A
OUT A
1
10
-IN A
2
9
OUT B
V+
+IN A
3
8
-IN B
GND
4
7
+IN B
N/C
5
6
N/C
Figure 3. 10 Lead CLGA Package
See Package Number NAC0010A
Schematic Diagram
(Each Amplifier)
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
2
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
LM158QML
www.ti.com
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
Absolute Maximum Ratings (1)
Supply Voltage, V+
32VDC
Differential Input Voltage
32VDC
−0.3VDC to +32VDC
Input Voltage
Power Dissipation (2)
830 mW
(3)
Output Short-Circuit to GND
(One Amplifier)
V+ ≤ 15VDC and TA = 25°C
Continuous
Maximum Junction Temperature (TJmax)
150°C
Input Current (VI < −0.3V) (4)
50 mA
Operating Temperature Range
−55°C ≤ TA ≤ +125°C
Storage Temperature Range
−65°C ≤ TA ≤ +150°C
Lead Temperature (Soldering, 10
seconds)
Thermal
Resistance
θJA
θJC
TO-99
300°C
CDIP
260°C
CLGA
260°C
TO-99 (Still Air)
80°C/W
CDIP (Still Air)
132°C/W
CDIP (500LF/Min Air Flow)
81°C/W
CLGA (Still Air)
195°C/W
CLGA (500LF/Min Air Flow)
131°C/W
TO-99
42°C/W
CDIP
23°C/W
CLGA
Package Weight
33°C/W
TO-99
1,000mg
CDIP
1,100mg
CLGA
220mg
ESD Tolerance (5)
(1)
(2)
(3)
(4)
(5)
155°C/W
TO-99 (500LF/Min Air Flow)
250V
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the
Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may
degrade when the device is not operated under the listed test conditions.
The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax (maximum junction temperature),
θJA (package junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any
temperature is PDmax = (TJmax - TA)/θJA or the number given in the Absolute Maximum Ratings, whichever is lower.
Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short circuits to ground,
the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15V,
continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result
from simultaneous shorts on all amplifiers.
This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of
the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is
also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages of the op amps to go to
the V+voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive and
normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than −0.3V (at 25°C).
Human body model, 1.5 kΩ in series with 100 pF.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
3
LM158QML
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
www.ti.com
Quality Conformance Inspection
Mil-Std-883, Method 5005 - Group A
4
Subgroup
Description
Temp °C
1
Static tests at
+25
2
Static tests at
+125
3
Static tests at
-55
4
Dynamic tests at
+25
5
Dynamic tests at
+125
6
Dynamic tests at
-55
7
Functional tests at
+25
8A
Functional tests at
+125
8B
Functional tests at
-55
9
Switching tests at
+25
10
Switching tests at
+125
11
Switching tests at
-55
12
Settling time at
+25
13
Settling time at
+125
14
Settling time at
-55
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
LM158QML
www.ti.com
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
LM158 Electrical Characteristics
SMD 5962–8771001 DC Parameters
The following conditions apply, unless otherwise specified.
Parameter
ICC
Power Supply Current
VOH
Output Voltage High
VOL
Output Voltage Low
ISink
Output Sink Current
All voltages referenced to device ground.
Max
Units
Subgroups
+VCC = 5V, RL = 100K,
VO = 1.4V
1.2
mA
1, 2, 3
+VCC = 30V, RL = 100K,
VO = 1.4V
3.0
mA
1
4.0
Test Conditions
Notes
mA
2, 3
+VCC = 30V, RL = 2KΩ
26
V
1, 2, 3
+VCC = 30V, RL = 10KΩ
27
V
1, 2, 3
+VCC = 30V, RL = 10KΩ
20
mV
1, 2, 3
+VCC = 30V, ISink = 1µA
20
mV
1, 2, 3
+VCC = 5V, RL = 10KΩ
20
mV
1, 2, 3
12
µA
1
10
mA
1
5.0
mA
2, 3
+VCC = 15V, VO = 200mV,
+VI = 0V, -VI = +65mV
+VCC = 15V, VO = 2V,
+VI = 0V, -VI = +65mV
ISource
Output Source Current
Min
+VCC = 15V, VO = 2V,
+VI = 0V, -VI = -65mV
-20
mA
1
-10
mA
2, 3
IOS
Short Circuit Current
+VCC = 5V, VO = 0V
-60
mA
1
VIO
Input Offset Voltage
+VCC = 30V, VCM = 0V,
RS = 50Ω, VO = 1.4V
-5.0
5.0
mV
1
-7.0
7.0
mV
2, 3
+VCC = 30V, VCM = 28.5V,
RS = 50Ω, VO = 1.4V
-5.0
5.0
mV
1
+VCC = 30V, VCM = 28V,
RS = 50Ω, VO = 1.4V
-7.0
7.0
mV
2, 3
+VCC = 5V, VCM = 0V,
RS = 50Ω, VO = 1.4V
-5.0
5.0
mV
1
-7.0
7.0
mV
2, 3
70
dB
1
CMRR
Common Mode Rejection Ratio
+VCC = 30V, RS = 50Ω
VI = 0V to 28.5V,
±IIB
Input BIas Current
+VCC = 5V, VCM = 0V
See (1)
-150
-1.0
nA
1
(1)
-300
-1.0
nA
2, 3
-30
30
nA
1
-100
100
nA
2, 3
dB
1
See
IIO
Input Offset Current
+VCC = 5V, VCM = 0V
PSRR
Power Supply Rejection Ratio
+VCC = 5V to 30V,
VCM = 0V
VCM
Common Mode Voltage Range
+VCC = 30V
VDiff
Differential Input Voltage
AVS
Large Signal Gain
(1)
(2)
(3)
(4)
65
See (2),
(3)
28.5
V
1
See (2),
(3)
28.0
V
2, 3
V
1, 2, 3
See (4)
+VCC = 15V, RL = 2KΩ,
VO = 1V to 11V
32
50
V/mV
4
25
V/mV
5, 6
The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The
upper end of the common-mode voltage range is V+ −1.5V (at 25°C), but either or both inputs can go to +32V without damage,
independent of the magnitude of V+.
Specified by input offset voltage.
Specified parameter not tested.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
5
LM158QML
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
LM158A Electrical Characteristics
www.ti.com
SMD 5962–8771002, High Dose Rate DC Parameters
The following conditions apply, unless otherwise specified.
Parameter
ICC
Power Supply Current
VOH
Output Voltage High
VOL
Output Voltage Low
All voltages referenced to device ground.
Max
Units
Subgroups
+VCC = 5V, RL = 100K,
VO = 1.4V
1.2
mA
1, 2, 3
+VCC = 30V, RL = 100K,
VO = 1.4V
3.0
mA
1
4.0
Test Conditions
Notes
Min
mA
2, 3
+VCC = 30V, RL = 2KΩ
26
V
1, 2, 3
+VCC = 30V, RL = 10KΩ
27
V
1, 2, 3
+VCC = 30V, RL = 10KΩ
+VCC = 30V, ISink = 1µA
Output Sink Current
+VCC = 15V, VO = 200mV,
+VI = 0V, -VI = +65mV
+VCC = 15V, VO = 2V,
+VI = 0V, -VI = +65mV
mV
1
mV
2, 3
40
mV
1
100
mV
2, 3
40
mV
1
100
mV
2, 3
12
µA
1
10
mA
1
5.0
mA
2, 3
-20
mA
1
-10
mA
2, 3
mA
1
+VCC = 5V, RL = 10KΩ
ISink
40
100
ISource
Output Source Current
+VCC = 15V, VO = 2V,
+VI = 0V, -VI = -65mV
IOS
Short Circuit Current
+VCC = 5V, VO = 0V
-60
VIO
Input Offset Voltage
+VCC = 30V, VCM = 0V,
RS = 50Ω, VO = 1.4V
-2.0
2.0
mV
1
-4.0
4.0
mV
2, 3
+VCC = 30V, VCM = 28.5V,
RS = 50Ω, VO = 1.4V
-2.0
2.0
mV
1
+VCC = 30V, VCM = 28V,
RS = 50Ω, VO = 1.4V
-4.0
4.0
mV
2, 3
+VCC = 5V, VCM = 0V,
RS = 50Ω, VO = 1.4V
-2.0
2.0
mV
1
-4.0
4.0
mV
2, 3
70
dB
1
CMRR
Common Mode Rejection Ratio
+VCC = 30V, RS = 50Ω
VI = 0V to 28.5V,
±IIB
Input BIas Current
+VCC = 5V, VCM = 0V
See (1)
See
IIO
Input Offset Current
+VCC = 5V, VCM = 0V
PSRR
Power Supply Rejection Ratio
+VCC = 5V to 30V,
VCM = 0V
VCM
Common Mode Voltage Range
+VCC = 30V
Differential Input Voltage
AVS
Large Signal Gain
See (2)
(1)
(2)
(3)
(4)
6
-1.0
nA
1
-100
-1.0
nA
2, 3
-10
10
nA
1
-30
30
nA
2, 3
dB
1
(3)
28.5
V
1
(2) (3)
28.0
V
2, 3
V
1, 2, 3
See
+VCC = 15V, RL = 2KΩ,
VO = 1V to 11V
-50
65
See
VDiff
(1)
(4)
32
50
V/mV
4
25
V/mV
5, 6
The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The
upper end of the common-mode voltage range is V+ −1.5V (at 25°C), but either or both inputs can go to +32V without damage,
independent of the magnitude of V+.
Specified by input offset voltage.
Specified parameter not tested.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
LM158QML
www.ti.com
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
SMD 5962–8771002, High Dose Rate
DC Drift Parameters
The following conditions apply, unless otherwise specified. All voltages referenced to device ground.
Delta calculations are performed on QMLV devices at Group B, Subgroup 5 only.
Parameter
VIO
Input Offset Voltage
±IIB
(1)
Input Bias Current
Min
Max
Units
Subgroups
+VCC = 30V, VCM = 0V,
RS = 50Ω, VO = 1.4V
-0.5
0.5
mV
1
+VCC = 30V, VCM = 28.5V,
RS = 50Ω, VO = 1.4V
-0.5
0.5
mV
1
+VCC = 5V, VCM = 0V,
RS = 50Ω, VO = 1.4V
-0.5
0.5
mV
1
-10
10
nA
1
Test Conditions
+VCC = 5V, VCM = 0V
Notes
See (1)
The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
SMD 5962–8771002, High Dose Rate SMD 5962–8771002, High Dose Rate
100K Post Radiation Limits @ +25°C (1)
DC Parameters
The following conditions apply, unless otherwise specified.
Parameter
VIO
(1)
(2)
Input Offset Voltage
±IIB
Input Bias Current
ICC
Power Supply Current
Test Conditions
Notes
Min
Max
Units
Sub groups
+VCC = 30V, VCM = 0V,
RS = 50Ω, VO = 1.4V
See (1)
-4.0
4.0
mV
1
+VCC = 30V, VCM = 28.5V,
RS = 50Ω, VO = 1.4V
See (1)
-4.0
4.0
mV
1
+VCC = 5V, VCM = 0V,
RS = 50Ω, VO = 1.4V
See (1)
-4.0
4.0
mV
1
+VCC = 5V, VCM = 0V
See (1) (2)
-60
-1.0
nA
1
1.5
mA
1
+VCC = 5V, RL = 100K,
VO = 1.4V
See (1)
Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics except as listed in the Post
Radiation Limits Table. These parts may be dose rate sensitive in a space environment and demonstrate enhanced low dose rate
sensitivity. Radiation end point limits for the noted parameters are specified only for the conditions as specified in MIL-STD-883, per
Test Method 1019, Condition A.
The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
LM158A Electrical Characteristics
DC Parameters
SMD 5962–8771003 ELDRS Free Only
The following conditions apply, unless otherwise specified.
Parameter
ICC
All voltages referenced to device ground.
Power Supply Current
VOH
Output Voltage High
VOL
Output Voltage Low
All voltages referenced to device ground.
Max
Units
Subgroups
+VCC = 5V, RL = 100K,
VO = 1.4V
1.2
mA
1, 2, 3
+VCC = 30V, RL = 100K,
VO = 1.4V
3.0
mA
1,
V
1, 2, 3
Test Conditions
Notes
Min
4.0
+VCC = 30V, RL = 2KΩ
26
+VCC = 30V, RL = 10KΩ
27
+VCC = 30V, RL = 10KΩ
+VCC = 30V, ISink = 1µA
+VCC = 5V, RL = 10KΩ
2, 3
V
1, 2, 3
40
mV
1
100
mV
2, 3
40
mV
1
100
mV
2, 3
40
mV
1
100
mV
2, 3
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
7
LM158QML
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
LM158A Electrical Characteristics
DC Parameters (continued)
www.ti.com
SMD 5962–8771003 ELDRS Free Only
The following conditions apply, unless otherwise specified.
Parameter
ISink
Output Sink Current
All voltages referenced to device ground.
Test Conditions
Notes
+VCC = 15V, VO = 200mV,
+VI = 0V, -VI = +65mV
+VCC = 15V, VO = 2V,
+VI = 0V, -VI = +65mV
ISource
Output Source Current
Units
Subgroups
12
µA
1
10
mA
1
5.0
mA
2, 3
Min
+VCC = 15V, VO = 2V,
+VI = 0V, -VI = -65mV
Max
-20
mA
1
-10
mA
2, 3
mA
1
IOS
Short Circuit Current
+VCC = 5V, VO = 0V
-60
VIO
Input Offset Voltage
+VCC = 30V, VCM = 0V,
RS = 50Ω, VO = 1.4V
-2.0
2.0
mV
1
-4.0
4.0
mV
2, 3
+VCC = 30V, VCM = 28.5V,
RS = 50Ω, VO = 1.4V
-2.0
2.0
mV
1
+VCC = 30V, VCM = 28V,
RS = 50Ω, VO = 1.4V
-4.0
4.0
mV
2, 3
+VCC = 5V, VCM = 0V,
RS = 50Ω, VO = 1.4V
-2.0
2.0
mV
1
-4.0
4.0
mV
2, 3
70
dB
1
CMRR
Common Mode Rejection Ratio
+VCC = 30V, RS = 50Ω
VI = 0V to 28.5V,
±IIB
Input BIas Current
+VCC = 5V, VCM = 0V
See (1)
See
IIO
Input Offset Current
+VCC = 5V, VCM = 0V
PSRR
Power Supply Rejection Ratio
+VCC = 5V to 30V,
VCM = 0V
VCM
Common Mode Voltage Range
+VCC = 30V
VDiff
Differential Input Voltage
AVS
Large Signal Gain
(1)
(2)
(3)
(4)
(1)
-50
-1.0
nA
1
-100
-1.0
nA
2, 3
-10
10
nA
1
-30
30
nA
2, 3
dB
1
65
See (2),
(3)
28.5
V
1
See (2),
(3)
28.0
V
2, 3
V
1, 2, 3
See (4)
+VCC = 15V, RL = 2KΩ,
VO = 1V to 11V
32
50
V/mV
4
25
V/mV
5, 6
The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The
upper end of the common-mode voltage range is V+ −1.5V (at 25°C), but either or both inputs can go to +32V without damage,
independent of the magnitude of V+.
Specified by input offset voltage.
Specified parameter not tested.
SMD 5962–8771003 ELDRS Free Only
DC Drift Parameters
The following conditions apply, unless otherwise specified. All voltages referenced to device ground.
Delta calculations are performed on QMLV devices at Group B, Subgroup 5 only.
Parameter
VIO
8
Input Offset Voltage
Min
Max
Units
Subgroups
+VCC = 30V, VCM = 0V,
RS = 50Ω, VO = 1.4V
-0.5
0.5
mV
1
+VCC = 30V, VCM = 28.5V,
RS = 50Ω, VO = 1.4V
-0.5
0.5
mV
1
+VCC = 5V, VCM = 0V,
RS = 50Ω, VO = 1.4V
-0.5
0.5
mV
1
Test Conditions
Submit Documentation Feedback
Notes
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
LM158QML
www.ti.com
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
SMD 5962–8771003 ELDRS Free Only
DC Drift Parameters (continued)
The following conditions apply, unless otherwise specified. All voltages referenced to device ground.
Delta calculations are performed on QMLV devices at Group B, Subgroup 5 only.
Parameter
±IIB
(1)
Input Bias Current
Test Conditions
+VCC = 5V, VCM = 0V
Notes
Min
Max
Units
Subgroups
See (1)
-10
10
nA
1
The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
SMD 5962–8771003 ELDRS Free Only
100K Post Radiation Limits @ +25°C (1)
DC Parameters
The following conditions apply, unless otherwise specified.
Parameter
VIO
±IIB
(1)
(2)
Input Offset Voltage
Input Bias Current
All voltages referenced to device ground.
Test Conditions
Notes
Min
Max
Units
Sub groups
+VCC = 30V, VCM = 0V,
RS = 50Ω, VO = 1.4V
See (1)
-4.0
4.0
mV
1
+VCC = 30V, VCM = 28.5V,
RS = 50Ω, VO = 1.4V
See (1)
-4.0
4.0
mV
1
+VCC = 5V, VCM = 0V,
RS = 50Ω, VO = 1.4V
See (1)
-4.0
4.0
mV
1
+VCC = 5V, VCM = 0V
See (1) (2)
-60
-1.0
nA
1
Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics except as listed in the Post
Radiation Limits Table. These parts may be sensitive in a high dose environment. Low dose rate testing has been performed on a
wafer-by-wafer basis, per Test Method 1019, Condition D of MIL-STD-883, with no enhanced low dose rate sensitivity (ELDRS).
The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
9
LM158QML
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics
10
Input Voltage Range
Input Current
Figure 4.
Figure 5.
Supply Current
Voltage Gain
Figure 6.
Figure 7.
Open Loop Frequency Response
Common-Mode Rejection Ratio
Figure 8.
Figure 9.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
LM158QML
www.ti.com
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
Typical Performance Characteristics (continued)
Voltage Follower Pulse Response
Voltage Follower Pulse Response (Small Signal)
Figure 10.
Figure 11.
Large Signal Frequency Response
Output Characteristics Current Sourcing
Figure 12.
Figure 13.
Output Characteristics Current Sinking
Current Limiting
Figure 14.
Figure 15.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
11
LM158QML
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
www.ti.com
APPLICATION HINTS
The LM158 series are op amps which operate with only a single power supply voltage, have true-differential
inputs, and remain in the linear mode with an input common-mode voltage of 0 VDC. These amplifiers operate
over a wide range of power supply voltage with little change in performance characteristics. At 25°C amplifier
operation is possible down to a minimum supply voltage of 2.3 VDC.
Precautions should be taken to insure that the power supply for the integrated circuit never becomes reversed in
polarity or that the unit is not inadvertently installed backwards in a test socket as an unlimited current surge
through the resulting forward diode within the IC could cause fusing of the internal conductors and result in a
destroyed unit.
Large differential input voltages can be easily accommodated and, as input differential voltage protection diodes
are not needed, no large input currents result from large differential input voltages. The differential input voltage
may be larger than V+ without damaging the device. Protection should be provided to prevent the input voltages
from going negative more than −0.3 VDC (at 25°C). An input clamp diode with a resistor to the IC input terminal
can be used.
To reduce the power supply current drain, the amplifiers have a class A output stage for small signal levels which
converts to class B in a large signal mode. This allows the amplifiers to both source and sink large output
currents. Therefore both NPN and PNP external current boost transistors can be used to extend the power
capability of the basic amplifiers. The output voltage needs to raise approximately 1 diode drop above ground to
bias the on-chip vertical PNP transistor for output current sinking applications.
For ac applications, where the load is capacitively coupled to the output of the amplifier, a resistor should be
used, from the output of the amplifier to ground to increase the class A bias current and prevent crossover
distortion. Where the load is directly coupled, as in dc applications, there is no crossover distortion.
Capacitive loads which are applied directly to the output of the amplifier reduce the loop stability margin. Values
of 50 pF can be accommodated using the worst-case non-inverting unity gain connection. Large closed loop
gains or resistive isolation should be used if larger load capacitance must be driven by the amplifier.
The bias network of the LM158 establishes a drain current which is independent of the magnitude of the power
supply voltage over the range of 3 VDC to 30 VDC.
Output short circuits either to ground or to the positive power supply should be of short time duration. Units can
be destroyed, not as a result of the short circuit current causing metal fusing, but rather due to the large increase
in IC chip dissipation which will cause eventual failure due to excessive junction temperatures. Putting direct
short-circuits on more than one amplifier at a time will increase the total IC power dissipation to destructive
levels, if not properly protected with external dissipation limiting resistors in series with the output leads of the
amplifiers. The larger value of output source current which is available at 25°C provides a larger output current
capability at elevated temperatures (see Typical Performance Characteristics) than a standard IC op amp.
The circuits presented in the section on typical applications emphasize operation on only a single power supply
voltage. If complementary power supplies are available, all of the standard op amp circuits can be used. In
general, introducing a pseudo-ground (a bias voltage reference of V+/2) will allow operation above and below this
value in single power supply systems. Many application circuits are shown which take advantage of the wide
input common-mode voltage range which includes ground. In most cases, input biasing is not required and input
voltages which range to ground can easily be accommodated.
12
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
LM158QML
www.ti.com
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
Typical Single-Supply Applications
(V+ = 5.0 VDC)
*R not needed due to temperature independent IIN
Figure 16. Non-Inverting DC Gain (0V Output)
VO = 0 VDC for VIN = 0 VDC
AV = 10
Where: VO = V1 + V2 −V3 − V4
(V1 + V2) ≥ (V3 + V4) to keep VO > 0 VDC
Figure 17. DC Summing Amplifier
(VIN'S ≥ 0 VDC and VO ≥ 0 VDC)
Figure 18. Power Amplifier
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
13
LM158QML
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
fo = 1 kHz
Q = 50
Av = 100 (40 dB)
www.ti.com
Figure 19. “BI-QUAD” RC Active Bandpass Filter
Figure 20. Fixed Current Sources
14
Submit Documentation Feedback
Figure 21. Lamp Driver
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
LM158QML
www.ti.com
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
*(Increase R1 for IL small)
VL ≤ V+ −2V
Figure 22. LED Driver
Figure 23. Current Monitor
VO = VIN
Figure 24. Driving TTL
Figure 25. Voltage Follower
Figure 26. Pulse Generator
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
15
LM158QML
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
www.ti.com
Figure 27. Squarewave Oscillator
HIGH ZIN
LOW ZOUT
16
Figure 28. Pulse Generator
Figure 29. Low Drift Peak Detector
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
LM158QML
www.ti.com
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
IO = 1 amp/volt VIN
(Increase RE for IO small)
Figure 30. High Compliance Current Sink
Figure 31. Comparator with Hysteresis
*WIDE CONTROL VOLTAGE RANGE: 0 VDC ≤ VC ≤ 2 (V+ −1.5V DC)
Figure 32. Voltage Controlled Oscillator (VCO)
Figure 33. AC Coupled Inverting Amplifier
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
17
LM158QML
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
www.ti.com
Figure 34. Ground Referencing a Differential Input Signal
Av = 11 (As Shown)
Figure 35. AC Coupled Non-Inverting Amplifier
fo = 1 kHz
Q=1
AV = 2
Figure 36. DC Coupled Low-Pass RC Active Filter
18
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
LM158QML
www.ti.com
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
fo = 1 kHz
Q = 25
Figure 37. Bandpass Active Filter
Figure 38. High Input Z, DC Differential Amplifier
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
19
LM158QML
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
www.ti.com
Figure 39. Photo Voltaic-Cell Amplifier
Figure 40. Bridge Current Amplifier
Figure 41. High Input Z Adjustable-Gain
DC Instrumentation Amplifier
20
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
LM158QML
www.ti.com
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
Figure 42. Using Symmetrical Amplifiers to
Reduce Input Current (General Concept)
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
21
LM158QML
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
www.ti.com
REVISION HISTORY
Changes from Revision E (March 2013) to Revision F
•
22
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 20
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
PACKAGE OPTION ADDENDUM
www.ti.com
27-Jul-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
5962-8771002GA
ACTIVE
TO-99
LMC
8
20
TBD
Call TI
Call TI
-55 to 125
LM158AH-SMD
5962-8771002GA Q A
CO
5962-8771002GA Q >
T
5962-8771002QXA
ACTIVE
CFP
NAC
10
54
TBD
Call TI
Call TI
-55 to 125
LM158AWG
/883 Q
5962-87710
(02QXA ACO ~ 02QYA
ACO)
(02QXA >T ~
02QYA >T)
5962R8771002V9A
ACTIVE
DIESALE
Y
0
38
Green (RoHS
& no Sb/Br)
Call TI
Level-1-NA-UNLIM
-55 to 125
5962R8771002VGA
ACTIVE
TO-99
LMC
8
20
TBD
Call TI
Call TI
-55 to 125
LM158AHRQMLV
5962R8771002VGA Q
ACO
5962R8771002VGA Q
>T
5962R8771002VPA
ACTIVE
CDIP
NAB
8
40
TBD
Call TI
Call TI
-55 to 125
LM158AJRQMLV
5962R87710
02VPA Q ACO
02VPA Q >T
5962R8771002VXA
ACTIVE
CFP
NAC
10
54
TBD
Call TI
Call TI
-55 to 125
LM158AWG
(RLQMLV Q ~
RQMLV Q)
5962R87710
02VXA ACO
02VXA >T
5962R8771003V9A
ACTIVE
DIESALE
Y
0
38
Green (RoHS
& no Sb/Br)
Call TI
Level-1-NA-UNLIM
25 Only
5962R8771003VGA
ACTIVE
TO-99
LMC
8
20
TBD
Call TI
Call TI
-55 to 125
LM158AHRLQMLV
5962R8771003VGA Q
ACO
5962R8771003VGA Q
>T
5962R8771003VPA
ACTIVE
CDIP
NAB
8
40
TBD
Call TI
Call TI
-55 to 125
LM158AJRLQV
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
27-Jul-2016
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
5962R87710
03VPA Q ACO
03VPA Q >T
5962R8771003VXA
ACTIVE
CFP
NAC
10
54
TBD
Call TI
Call TI
-55 to 125
LM158 MD8
ACTIVE
DIESALE
Y
0
400
Green (RoHS
& no Sb/Br)
Call TI
Level-1-NA-UNLIM
-55 to 125
LM158 MW8
ACTIVE
WAFERSALE
YS
0
1
Green (RoHS
& no Sb/Br)
Call TI
Level-1-NA-UNLIM
-55 to 125
LM158A MDE
ACTIVE
DIESALE
Y
0
38
Green (RoHS
& no Sb/Br)
Call TI
Level-1-NA-UNLIM
-55 to 125
LM158A MDR
ACTIVE
DIESALE
Y
0
38
Green (RoHS
& no Sb/Br)
Call TI
Level-1-NA-UNLIM
-55 to 125
LM158AH-SMD
ACTIVE
TO-99
LMC
8
20
TBD
Call TI
Call TI
-55 to 125
LM158AH-SMD
5962-8771002GA Q A
CO
5962-8771002GA Q >
T
LM158AH/883
ACTIVE
TO-99
LMC
8
20
TBD
Call TI
Call TI
-55 to 125
LM158AH/883 Q ACO
LM158AH/883 Q >T
LM158AHRLQMLV
ACTIVE
TO-99
LMC
8
20
TBD
Call TI
Call TI
-55 to 125
LM158AHRLQMLV
5962R8771003VGA Q
ACO
5962R8771003VGA Q
>T
LM158AHRQMLV
ACTIVE
TO-99
LMC
8
20
TBD
Call TI
Call TI
-55 to 125
LM158AHRQMLV
5962R8771002VGA Q
ACO
5962R8771002VGA Q
>T
LM158AJ/883
ACTIVE
CDIP
NAB
8
40
TBD
Call TI
Call TI
-55 to 125
LM158AJ/883
5962-87710
02PA Q ACO
02PA Q >T
LM158AJRLQMLV
ACTIVE
CDIP
NAB
8
40
TBD
Call TI
Call TI
-55 to 125
LM158AJRLQV
5962R87710
Addendum-Page 2
LM158AWG
RLQMLV Q
5962R87710
03VXA ACO
03VXA >T
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
27-Jul-2016
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
03VPA Q ACO
03VPA Q >T
LM158AJRQMLV
ACTIVE
CDIP
NAB
8
40
TBD
Call TI
Call TI
-55 to 125
LM158AJRQMLV
5962R87710
02VPA Q ACO
02VPA Q >T
LM158AWG/883
ACTIVE
CFP
NAC
10
54
TBD
Call TI
Call TI
-55 to 125
LM158AWG
/883 Q
5962-87710
(02QXA ACO ~ 02QYA
ACO)
(02QXA >T ~
02QYA >T)
LM158AWGRLQMLV
ACTIVE
CFP
NAC
10
54
TBD
Call TI
Call TI
-55 to 125
LM158AWG
RLQMLV Q
5962R87710
03VXA ACO
03VXA >T
LM158AWGRQMLV
ACTIVE
CFP
NAC
10
54
TBD
Call TI
Call TI
-55 to 125
LM158AWG
(RLQMLV Q ~
RQMLV Q)
5962R87710
02VXA ACO
02VXA >T
LM158H/883
ACTIVE
TO-99
LMC
8
20
TBD
Call TI
Call TI
-55 to 125
LM158H/883 Q ACO
LM158H/883 Q >T
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Addendum-Page 3
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
27-Jul-2016
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LM158QML, LM158QML-SP :
• Military: LM158QML
• Space: LM158QML-SP
NOTE: Qualified Version Definitions:
• Military - QML certified for Military and Defense Applications
• Space - Radiation tolerant, ceramic packaging and qualified for use in Space-based application
Addendum-Page 4
MECHANICAL DATA
NAB0008A
J08A (Rev M)
www.ti.com
MECHANICAL DATA
NAC0010A
WG10A (Rev H)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated
Similar pages