TI1 LM5121QMHX/NOPB Wide input synchronous boost controller with disconnection switch control Datasheet

LM5121/LM5121-Q1
www.ti.com
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
Wide Input Synchronous Boost Controller with Disconnection Switch Control
Check for Samples: LM5121/LM5121-Q1
FEATURES
1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
2
•
•
•
•
•
•
•
Available in AEC-Q100 (TJ = –40ºC to 125ºC)
Maximum Input Voltage: 65 V
Min Input Voltage: 3.0 V (4.5 V for startup)
Output Voltage up to 100 V
Bypass (VOUT = VIN) Operation
1.2 V Reference with ±1.0% Accuracy
Free-Run/Synchronizable up to 1 MHz
Peak Current Mode Control
Robust Integrated 3 A Gate Drivers
Adaptive Dead-Time Control
Optional Diode Emulation Mode
Programmable Cycle-by-Cycle Current Limit
Programmable Line UVLO
Programmable Soft-Start
Thermal Shutdown Protection
Low Shutdown Quiescent Current: 9 μA
Programmable Slope Compensation
Programmable Skip Cycle Mode Reduces
Standby Power
Supports External VCC Bias Supply Option
Load Disconnection in Shutdown Mode (True
Shutdown)
Inrush Current Limiting
Hiccup Mode Short Circuit / Overload
Protection
Circuit Breaker Function
Capable of Input Transient Suppression
Capable of Reverse Battery Protection
•
Thermally Enhanced 20-Pin HTSSOP Package
APPLICATIONS
•
•
•
•
12 V, 24 V, and 48 V Power Systems
Automotive Start-Stop
High Current Boost Power Supply
Battery Powered System
DESCRIPTION
The LM5121 is a synchronous boost controller
intended for high-efficiency, high power boost
regulator applications. The control method is based
upon peak current mode control. Current mode
control provides inherent line feed-forward, cycle-bycycle current limiting and ease of loop compensation.
The switching frequency is programmable up to 1
MHz. Higher efficiency is achieved using two robust
N-channel MOSFET gate drivers with adaptive deadtime control. A user-selectable diode emulation mode
enables discontinuous mode operation for improved
efficiency at light load conditions.
The LM5121 provides disconnection switch control
which completely disconnects the output from the
input during an output short or a shutdown condition.
During start-up sequence, inrush current is limited by
the disconnection switch control.
An internal charge pump allows 100% duty cycle
operation of the high-side synchronous switch
(Bypass operation). Additional features include
thermal shutdown, frequency synchronization, hiccup
mode current limit and adjustable line undervoltage
lockout.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2013, Texas Instruments Incorporated
LM5121/LM5121-Q1
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
www.ti.com
SIMPLIFIED APPLICATION DIAGRAM
VIN
VOUT
+
VCC
DS
BST
DG
CSN
CSP
VIN
UVLO
SLOPE
SYNCIN/RT
LM5121
SW
LO
HO
COMP
FB
RES
SS
MODE
PGND
AGND
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
2
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
LM5121/LM5121-Q1
www.ti.com
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
ABSOLUTE MAXIMUM RATINGS (1)
Over operating free-air temperature range (unless otherwise noted)
VALUE
Input
Output (3)
ESD Rating
Thermal
(1)
(2)
(3)
MIN
MAX
VIN, CSP, CSN
–0.3
75
BST to SW, FB, MODE, UVLO, VCC (2)
–0.3
15
SW
–5.0
105
BST
–0.3
115
SS, SLOPE, SYNCIN/RT
–0.3
7
CSP to CSN, PGND
–0.3
0.3
DG to DS
–3.0
18
DG to VIN
–75
15
DS
–3.0
75
HO to SW
–0.3
BST to SW+0.3
LO
–0.3
VCC+0.3
COMP, RES
–0.3
7
Human-Body Model (HBM) JESD22-A114
2
Charged-Device Model (CDM) JESD22-C101
1
Storage Temperature
–55
150
Junction Temperature
–40
150
UNIT
V
kV
ºC
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions are not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Unless
otherwise specified, all voltages are referenced to AGND pin.
See Application Information when input supply voltage is less than the VCC voltage.
All output pins are not specified to have an external voltage applied.
THERMAL CHARACTERISTICS
THERMAL METRIC
UNIT
θJA Junction-to-ambient thermal resistance (Typ.)
40
θJC Junction-to-case thermal resistance (Typ.)
4
ºC/W
RECOMMENDED OPERATING CONDITIONS (1)
Over operating free-air temperature range (unless otherwise noted)
Input supply voltage
(2)
MIN
MAX
VIN
4.5
65
Disconnection switch voltage (2)
DG, DS
3.0
65
Low-side driver bias voltage
VCC
High-side driver bias voltage
BST to SW
3.8
Current sense common mode range (2)
CSP, CSN
3.0
Switch node voltage
SW
Junction temperature
TJ
(1)
(2)
UNIT
14
14
V
65
100
–40
125
ºC
Recommended Operating Conditions are conditions under which operation of the device is intended to be functional, but does not
guarantee specific performance limits.
Minimum VIN operating voltage is always 4.5 V. The minimum input power supply voltage can be 3.0 V after start-up, assuming VIN
voltage is supplied from an available external source.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
3
LM5121/LM5121-Q1
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
www.ti.com
ELECTRICAL CHARACTERISTICS
Unless otherwise specified, these specifications apply for -40°C ≤ TJ ≤ +125°C, VVIN = 12 V, VVCC = 8.3 V, RT = 20 kΩ, no
load on LO and HO. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference
purposes only.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
VUVLO = 0 V
9
17
µA
VUVLO = 2 V, non-switching
4
5
mA
7.6
8.3
VIN SUPPLY
ISHUTDOWN VIN shutdown current
IBIAS
VIN operating current (exclude the current
into RT resistor)
VCC REGULATOR
VCC(REG)
VCC regulation
No load
VVIN = 4.5 V, no external load
VCC dropout (VIN to VCC)
IVCC
6.9
0.25
VVIN = 4.5 V, IVCC = 25 mA
0.28
VCC sourcing current limit
VVCC = 0 V
VCC operating current (exclude the current
into RT resistor)
VVCC = 8.3 V
3.5
5
VVCC = 12 V
4.5
8
4.0
4.1
VCC undervoltage threshold
VCC rising, VVIN = 4.5 V
50
3.9
62
VCC falling, VVIN = 4.5 V
VCC undervoltage hysteresis
V
0.5
mA
3.7
V
1.23
V
µA
0.385
UNDERVOLTAGE LOCKOUT
UVLO threshold
UVLO rising
UVLO hysteresis current
VUVLO = 1.4 V
UVLO standby threshold
UVLO rising
1.17
1.20
7
10
13
0.3
0.4
0.5
0.1
0.125
1.24
1.28
UVLO standby hysteresis
V
MODE
Diode emulation mode threshold
MODE rising
1.20
Diode emulation mode hysteresis
0.1
Default MODE voltage
Default skip cycle threshold
Skip cycle hysteresis
145
155
COMP rising, measured at COMP
1.290
COMP falling, measured at COMP
1.245
Measured at COMP
170
V
mV
V
40
mV
ERROR AMPLIFIER
VREF
FB reference voltage
Measured at FB, VFB= VCOMP
FB input bias current
VFB= VREF
VOH
COMP output high voltage
VOL
COMP output low voltage
AOL
DC gain
fBW
Unity gain bandwidth
1.188
1.200
1.212
5
ISOURCE = 2 mA, VVCC = 4.5 V
2.75
ISOURCE = 2 mA, VVCC = 12 V
3.40
V
nA
V
ISINK = 2 mA
0.25
80
dB
3
MHz
OSCILLATOR
fSW1
Switching frequency 1
RT = 20 kΩ
400
450
500
fSW2
Switching frequency 2
RT = 10 kΩ
775
875
975
RT output voltage
kHz
1.2
RT sync rising threshold
RT rising
RT sync falling threshold
RT falling
Minimum sync pulse width
2.5
1.6
2.9
V
2.0
100
ns
DISCONNECTION SWITCH CONTROL
IDIS-SOURCE
DG current source
UVLO = 2 V, Sourcing
25
IDIS-SINK
DG current sink
Inrush Control, Sinking
67
DG discharge switch RDS-ON
Circuit Breaker
38
4
Submit Documentation Feedback
uA
Ω
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
LM5121/LM5121-Q1
www.ti.com
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
ELECTRICAL CHARACTERISTICS (continued)
Unless otherwise specified, these specifications apply for -40°C ≤ TJ ≤ +125°C, VVIN = 12 V, VVCC = 8.3 V, RT = 20 kΩ, no
load on LO and HO. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference
purposes only.
PARAMETER
TEST CONDITIONS
DG charge pump regulation
DG to VIN, No load, VVIN = 4.5 V
MIN
TYP
MAX
9.5
10.5
11.5
DG to VIN, No load, VVIN = 12 V
VGS-DET
VGS detection threshold
DG to DS, Rising, VVIN = 12 V
12.5
4.0
VGS detection hysteresis
5.4
6.5
UNIT
V
0.2
Transconductance gain
CSP to CSN to IDG
12
uA/mV
SLOPE COMPENSATION
SLOPE output voltage
VSLOPE
Slope compensation amplitude
1.17
1.20
1.23
RSLOPE = 20 kΩ, fSW = 100 kHz, 50%
duty cycle, TJ = –40ºC to +125ºC
1.375
1.650
1.925
RSLOPE= 20 kΩ, fSW= 100 kHz, 50%
duty cycle, TJ = 25ºC
1.400
1.650
1.900
7.5
10
12
V
SOFT-START
ISS-SOURCE SS current source
VSS = 0 V
SS discharge switch RDS-ON
µA
Ω
13
PWM COMPARATOR
tLO-OFF
tON-MIN
Forced LO off-time
Minimum LO on-time
COMP to PWM voltage drop
VVCC = 5.5 V
420
550
VVCC = 4.5 V
360
500
RSLOPE = 20 kΩ
150
RSLOPE = 200 kΩ
300
TJ = –40ºC to +125ºC
0.95
1.10
1.25
TJ = 25ºC
1.00
1.10
1.20
CSP to CSN, TJ = –40ºC to +125ºC
65.5
75.0
87.5
CSP to CSN, TJ = 25ºC
67.0
75.0
86.0
80
110
133
143
160
170
11.5
16.0
ns
V
CURRENT SENSE / CYCLE-BY-CYCLE CURRENT LIMIT
VCS-TH1
Cycle-by-cycle current limit threshold
VCS-TH2 –VCS-TH1
VCS-TH2
Inrush current limit threshold
CSP to CSN
VCS-TH3
Circuit breaker enable threshold
CSP to CSN, Rising
VCS-TH4
VCS-ZCD
Circuit breaker disable threshold
Zero cross detection threshold
5
VCS-TH3 – VCS-TH2
20
CSP to CSN, Falling
4.0
CSP to CSN, Rising
CSP to CSN, Falling
7
0.3
6
Current sense amplifier gain
10
ICSP
CSP input bias current
12
ICSN
CSN input bias current
12
V/V
11
Bias current matching
ICSP to ICSN
CS to LO delay
Current sense / current limit delay
mV
–1.75
1
µA
3.75
150
ns
HICCUP MODE RESTART
VRES
VHCPUPPER
VHCP-
Restart threshold
Hiccup counter upper threshold
Hiccup counter lower threshold
LOWER
RES rising
RES rising
RES rising, VVIN = VVCC = 4.5 V
1.15
1.20
1.25
4.2
3.6
RES falling
2.15
RES falling, VVIN = VVCC = 4.5 V
1.85
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
V
5
LM5121/LM5121-Q1
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
Unless otherwise specified, these specifications apply for -40°C ≤ TJ ≤ +125°C, VVIN = 12 V, VVCC = 8.3 V, RT = 20 kΩ, no
load on LO and HO. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference
purposes only.
PARAMETER
IRES-
TEST CONDITIONS
RES current source1
Fault-state charging current
RES current sink1
Normal-state discharging current
RES current source2
Hiccup mode off-time charging current
RES current sink2
Hiccup mode off-time discharging
current
MIN
TYP
MAX
20
30
40
UNIT
SOURCE1
IRES-SINK1
IRES-
5
µA
10
SOURCE2
IRES-SINK2
5
Hiccup cycle
RES discharge switch RDS-ON
Ratio of hiccup mode off-time to restart
delay time
8
Cycles
40
Ω
122
HO GATE DRIVER
VOHH
HO high-state voltage drop
IHO = –100 mA, VOHH = VBST – VHO
VOLH
HO low-state voltage drop
IOHH
0.15
0.24
IHO = 100 mA, VOLH = VHO – VSW
0.1
0.18
HO rise time (10% to 90%)
CLOAD = 4700 pF, VBST = 12 V
25
HO fall time (90% to 10%)
CLOAD = 4700 pF, VBST = 12 V
20
VHO = 0 V, VSW = 0 V, VBST = 4.5 V
0.8
VHO = 0 V, VSW = 0 V, VBST = 7.6 V
1.9
VHO = VBST = 4.5 V
1.9
Peak HO source current
IOLH
Peak HO sink current
IBST
BST charge pump sourcing current
BST charge pump regulation
VHO = VBST = 7.6 V
A
3.2
90
200
BST to SW, IBST= –70 μA,
VVIN = VSW = 9.0 V
5.3
6.2
6.75
7
8.5
9
2.0
3.0
3.5
30
45
BST to SW undervoltage
BST DC bias current
ns
VVIN = VSW = 9.0 V , VBST - VSW = 5.0 V
BST to SW, IBST = –70 μA,
VVIN = VSW = 12 V
V
VBST - VSW = 12 V, VSW = 0 V
µA
V
µA
LO GATE DRIVER
VOHL
LO high-state voltage drop
ILO = –100 mA, VOHL = VVCC – VLO
0.15
0.25
VOLL
LO low-state voltage drop
ILO = 100 mA, VOLL = VLO
0.1
0.17
LO rise time (10% to 90%)
CLOAD = 4700 pF
25
LO fall time (90% to 10%)
CLOAD = 4700 pF
20
VLO = 0 V, VVCC = 4.5 V
0.8
VLO = 0 V
2.0
VLO = VVCC = 4.5 V
1.8
VLO = VVCC
3.2
IOHL
Peak LO source current
IOLL
Peak LO sink current
V
ns
A
SWITCHING CHARACTERISTICS
tDLH
LO fall to HO rise delay
No load, 50% to 50%
50
80
115
tDHL
HO fall to LO rise delay
No load, 50% to 50%
60
80
105
Thermal shutdown
Temperature rising
ns
THERMAL
TSD
Thermal shutdown hysteresis
6
165
25
Submit Documentation Feedback
ºC
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
LM5121/LM5121-Q1
www.ti.com
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
TYPICAL CHARACTERISTICS
6.00
5.00
4.00
3.00
LO PEAK CURRENT [A]
HO PEAK CURRENT [A]
5.00
SINK
2.00
SOURCE
1.00
4.00
SINK
3.00
SOURCE
2.00
1.00
VVIN = 12V
VSW = 0V
VVIN = 12V
0.00
0.00
4
5
6
7
8
9
10
11
12
13
VBST - VSW [V]
4
14
7
8
100
90.00
95
80.00
90
Dead-time [ns]
70.00
60.00
tDHL
50.00
40.00
tDLH
VVIN = 12V
VSW = 12V
CLOAD=2600pF
1V to 1V
20.00
10.00
9
10
11
12
13
14
C001
Figure 2. LO Peak Current vs VVCC
100.00
Dead-time [ns]
6
VVCC [V]
Figure 1. HO Peak Current vs VBST - VSW
30.00
5
C001
tDHL
85
80
75
70
tDLH
65
60
55
0.00
50
4
5
6
7
8
9
10
11
VVCC [V]
12
-50
-25
0
25
50
75
100
125
Temperature [ƒC]
C001
Figure 3. Dead Time vs VVCC
150
C001
Figure 4. Dead Time vs Temperature
100.0
20
90.0
15
70.0
tDHL
ISHUTDOWN [PA]
Dead-time [ns]
80.0
60.0
50.0
40.0
tDLH
30.0
VVIN = 12V
VVCC = 7.6V
CLOAD = 2600pF
1V to 1V
20.0
10.0
10
5
0.0
0
0
10
20
30
40
VSW [V]
50
60
-50
-25
Figure 5. Dead Time vs VSW
0
25
50
75
100
125
Temperature [ƒC]
C001
150
C001
Figure 6. ISHUTDOWN vs Temperature
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
7
LM5121/LM5121-Q1
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
www.ti.com
TYPICAL CHARACTERISTICS (continued)
8
8
No load
6
VVCC [V]
VVCC [V]
6
4
4
2
2
0
0
No load
0
10
20
30
40
50
60
70
0
80
IVCC [mA]
1
2
3
4
5
6
7
Figure 7. VVCC vs IVCC
9
10
11
12
13
14
C001
Figure 8. VVCC vs VVIN
40
15
180
ACL=101, COMP unload
ICSP
30
135
PHASE
20
90
10
45
0
10000
100000
FREQUENCY [Hz]
10
ICSN
5
0
GAIN
-10
1000
ICSP, ICSN [PA]
PHASE [°]
GAIN [dB]
8
VVIN [V]
C001
0
-45
10000000
1000000
-50
-25
0
25
50
75
100
125
Temperature [ƒC]
C002
Figure 9. Error Amp Gain and Phase vs Frequency
150
C001
Figure 10. ICSP, ICSN vs Temperature
15.0
300
280
BST Charging Current [PA]
IBST = -70uA
VBST-SW [V]
10.0
5.0
VVIN=VSW=9V
260
240
220
200
180
160
140
120
100
0.0
4
9
14
-50
19
VSW [V]
-25
VCS-TH1, VCS-TH2, VCS-TH3 [mV]
VCS-TH1, VCS-TH2, VCS-TH3 [mV]
VCS-TH3
150
VCS-TH2
100
VCS-TH1
50
6
7
8
9
10
11
VVIN [V]
12
200
190
180
170
160
150
140
130
120
110
100
90
80
70
60
50
75
100
125
150
C001
VCS-TH3
VCS-TH2
VCS-TH1
±50
±25
C001
Figure 13. VCS-TH1, VCS-TH2, VCS-TH3 vs VVIN
8
50
Figure 12. IBST vs Temperature
200
5
25
Temperature [ƒC]
Figure 11. VBST-SW vs VSW
4
0
C001
0
25
50
75
Temperature [ƒC]
100
125
150
C001
Figure 14. VCS-TH1 VCS-TH2, VCS-TH3 vs Temperature
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
LM5121/LM5121-Q1
www.ti.com
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
TYPICAL CHARACTERISTICS (continued)
12
12
11
10
VDG-DS [V]
11
500 kŸ
No Load
8
VDG-DS [V]
9
7
6
5
250 kŸ
10
4
3
9
2
VDS=12V
1
0
8
4
5
6
7
8
9
10
11
VVIN [V]
12
±50
0
±25
25
50
75
100
125
Temperature [ƒC]
C001
Figure 15. VDG-DS vs VVIN
150
C001
Figure 16. VDG-DS vs Temperature
12.00
11.00
10.00
VSW = 12V
9.00
VBST-SW [V]
8.00
7.00
6.00
5.00
VSW = 9V
4.00
3.00
VVIN = VSW
IBST = -70uA
2.00
1.00
0.00
-50
-25
0
25
50
75
100
Temperature [ƒC]
125
150
C001
Figure 17. VBST-SW vs Temperature
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
9
LM5121/LM5121-Q1
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
www.ti.com
DEVICE INFORMATION
HTSSOP-20
(TOP VIEW)
DS
1
20
BST
DG
2
19
HO
CSN
3
18
SW
CSP
4
17
VCC
VIN
5
16
LO
EP
UVLO
6
15
PGND
SS
7
14
RES
SYNCIN/RT
8
13
MODE
AGND
9
12
SLOPE
FB
10
11
COMP
PIN FUNCTIONS
PIN
10
DESCRIPTION
NO.
AGND
9
G
Analog ground connection. Return for the internal voltage reference and analog circuits.
BST
20
P/I
High-side driver supply for bootstrap gate drive. Connect to the cathode of the external bootstrap
diode and to the bootstrap capacitor. The bootstrap capacitor supplies current to charge the highside N-channel MOSFET gate and should be placed as close to controller as possible. An internal
BST charge pump will supply 200 µA current into bootstrap capacitor for bypass operation.
COMP
11
O
Output of the internal error amplifier. The loop compensation network should be connected between
this pin and the FB pin.
CSN
3
I
Inverting input of current sense amplifier. Connect to the negative-side of the current sense resistor.
CSP
4
I
Non-inverting input of current sense amplifier. Connect to the positive-side of the current sense
resistor.
DG
2
O
Disconnection switch control pin. Connect to the gate terminal of the N-channel MOSFET
disconnection switch.
DS
1
I/O
Source connection of N-channel MOSFET disconnection switch. Connect to the source terminal of
the disconnection switch, the cathode terminal of the freewheeling diode and the supply input of
boost inductor.
EP
EP
N/A
Exposed pad of the package. No internal electrical connections. Should be soldered to the large
ground plane to reduce thermal resistance.
FB
10
I
Feedback. Inverting input of the internal error amplifier. A resistor divider from the output to this pin
sets the output voltage level. The regulation threshold at the FB pin is 1.2 V.
HO
19
O
High-side N-channel MOSFET gate drive output. Connect to the gate of the high-side synchronous
N-channel MOSFET switch through a short, low inductance path.
LO
16
O
Low-side N-channel MOSFET gate drive output. Connect to the gate of the low-side N-channel
MOSFET switch through a short, low inductance path.
I
Switching mode selection pin. Internal 700 kΩ pull-up and 100 kΩ pull-down resistor hold MODE pin
to 0.15 V as a default. By adding external pull-up or pull-down resistor, MODE pin voltage can be
programmed. When MODE pin voltage is greater than 1.2 V, diode emulation mode threshold,
forced PWM mode is enabled, allowing current to flow in either direction through the high-side Nchannel MOSFET switch. When MODE pin voltage is less than 1.2 V, the controller works in diode
emulation mode. Skip cycle comparator is activated as a default condition when the MODE pin is
left floating. If the MODE pin is grounded, the controller still operates in diode emulation mode, but
the skip cycle comparator will not be triggered in normal operation, this enables pulse skipping
operation at light load.
MODE
(1)
I/O (1)
NAME
13
G = Ground, I = Input, O = Output, P = Power
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
LM5121/LM5121-Q1
www.ti.com
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
PIN
I/O (1)
DESCRIPTION
NAME
NO.
PGND
15
G
Power ground connection pin for low-side N-channel MOSFET gate driver. Connect directly to the
source terminal of the low-side N-channel MOSFET switch.
RES
14
O
The restart timer pin for an external capacitor that configures hiccup mode off-time and restart delay
during over load conditions and hiccup mode short circuit protection. Connect directly to the AGND
when hiccup mode operation is not required.
SLOPE
12
I
Slope compensation is programmed by an external resistor between SLOPE and the AGND.
SS
7
I
Soft-start programming pin. An external capacitor and an internal 10 μA current source set the ramp
rate of the internal error amplifier reference during soft-start.
SW
18
I/O
Switching node of the boost regulator. Connect to the bootstrap capacitor, the source terminal of the
high-side N-channel MOSFET switch and the drain terminal of the low-side N-channel MOSFET
switch through short, low inductance paths.
SYNCIN/RT
8
I
The internal oscillator frequency is programmed by an external resistor between RT and the AGND.
The internal oscillator can be synchronized to an external clock by applying a positive pulse signal
into this pin. The recommended maximum internal oscillator frequency is 2 MHz which leads to 1
MHz maximum switching frequency.
UVLO
6
I
Undervoltage lockout programming pin. If the UVLO pin is below 0.4 V, the regulator is in the
shutdown mode with all functions disabled. If the UVLO pin voltage is greater than 0.4 V and below
1.2 V, the regulator is in standby mode with the VCC regulator operational and no switching at the
HO and LO outputs. If the UVLO pin voltage is above 1.2 V, the startup sequence begins. A 10 μA
current source at UVLO pin is enabled when UVLO exceeds 1.2 V and flows through the external
UVLO resistors to provide hysteresis. The UVLO pin should not be left floating.
VCC
17
P/O/I
VCC bias supply pin. Locally decouple to PGND using a low ESR/ESL capacitor located as close to
controller as possible.
VIN
5
P/I
Supply voltage input source for the VCC regulator. Connect to the input capacitor and source power
supply connection with short, low impedance paths.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
11
LM5121/LM5121-Q1
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
www.ti.com
FUNCTIONAL BLOCK DIAGRAM
VIN
QD
RS
CIN
CSP
VIN
10µA
DF
DG Charge Pump
STANDBY
+
1.1V
+
UVLO
RUV1
CS A=10
AMP
0.4V/0.3V
+
SHUTDOWN
9
VSLOPE =
CHF
COMP
+
+
-
- ZCD threshold
+ ERR
+
PWM
Comparator
10µA
SW
COUT
CLK
S
Q
PWM
LO
Adaptive
Timer
QL
R Q
1.2V
RFB2
Skip Cycle
Comparator
700k
20mV
+
MODE
100k
VOUT
CBST
VCC
+
-
SS
Level Shift
Diode Emulation
C/L
Comparator
AMP
CSS
BST
+
-
FB
1.2V
CVCC
DBST
HO
+
750mV
CCOMP RCOMP
BST Charge Pump
QH
VSENSE2
1.2 V
VCC
VCC
Regulator
Circuit Breaker
Comparator
VSENSE1
6 u 10
RSLOPE u FSW
VIN
+
-
1.6V/0.11V
SLOPE
Generator
AMP
+
Inrush Current
Limiter
SLOPE
RSLOPE
VIN
25µA
1.2V
RUV2
LIN
DS
DG
CSN
1.2V
-
+
+
Diode
Emulation
Comparator
30µA
40mV
Hysteresis
Diode
Emulation
LM5121
CLK
10µA
Restart
Timer
RFB1
Clock Generator
/SYNC Detector
RES
5µA
AGND
SYNCIN/RT
CRES
PGND
RT
Functional Description
The LM5121 wide input range synchronous boost controller features all of the functions necessary to implement
a highly efficient synchronous boost regulator. The regulator control method is based upon peak current mode
control. Peak current mode control provides inherent line feed-forward and ease of loop compensation. This
highly integrated controller provides strong high-side and low-side N-channel MOSFET drivers with adaptive
dead-time control. The switching frequency is user programmable up to 1 MHz, either set by a single resistor or
synchronized to an external clock.
The control mode of high-side synchronous switch can be configured as either forced PWM (FPWM) or diode
emulation mode. Fault protection features include cycle-by-cycle current limiting, hiccup mode over load
protection, hiccup mode short circuit protection, thermal shutdown and remote shutdown capability by pulling
down the UVLO pin. The UVLO input enables the controller when the input voltage reaches a user selected
threshold, and provides tiny 9 μA shutdown quiescent current when pulled low. LM5121's unique disconnection
switch control provides numerous additional advantages. True Shutdown allows disconnecting load from the
input, blocking leakage current paths in shutdown mode. Inrush current control limits input current during initial
charging of the output capacitor. Circuit breaker function quickly switches off the disconnection switch,
terminating any severe over-current condition. Hiccup mode short circuit protection minimizes power dissipation
during prolonged output short condition. Input over voltage suppression can be achieved by connecting a Zener
diode from the disconnection MOSFET gate pin to ground. The device is available in 20-pin HTSSOP package
featuring an exposed pad to aid in thermal dissipation.
12
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
LM5121/LM5121-Q1
www.ti.com
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
Undervoltage Lockout (UVLO)
The LM5121 features a dual level UVLO circuit. When the UVLO pin voltage is less than the 0.4 V UVLO
standby threshold, the LM5121 is in the shutdown mode with all functions disabled. The shutdown comparator
provides 0.1 V of hysteresis to avoid chatter during transitions. If the UVLO pin voltage is greater than 0.4 V and
below 1.2 V during power up, the controller is in the standby mode with the VCC regulator operational, the
disconnection switch disabled and no switching at the HO and LO outputs. This feature allows the UVLO pin to
be used as a remote shutdown function by pulling the UVLO pin down below the UVLO standby threshold with
an external open collector or open drain device.
VIN
UVLO Hysteresis
Current
RUV2
RUV1
STANDBY
UVLO
UVLO
Threshold
UVLO Standby
Enable Threshold
SHUTDOWN
+
+
STANDBY
SHUTDOWN
Figure 18. UVLO Remote Standby and Shutdown Control
If the UVLO pin voltage is above 1.2 V UVLO threshold and VCC voltage exceeds the VCC UV threshold, the
startup sequence begins. UVLO hysteresis is accomplished with an internal 10 μA current source that is switched
on or off into the impedance of the UVLO setpoint divider. When the UVLO pin voltage exceeds the 1.2 V, the
current source is enabled to quickly raise the voltage at the UVLO pin. When the UVLO pin voltage falls below
the 1.2 V UVLO threshold, the current source is disabled causing the voltage at the UVLO pin to quickly fall. In
addition to the UVLO hysteresis current source, a 5 μs deglitch filter on both rising and falling edge of UVLO
toggling helps preventing chatter during power up or down.
An external UVLO setpoint voltage divider from the supply voltage to AGND is used to set the minimum input
operating voltage of the regulator. The divider must be designed such that the voltage at the UVLO pin is greater
than 1.2 V when the input voltage is in the desired operating range. The maximum voltage rating of the UVLO
pin is 16 V. If necessary, the UVLO pin can be clamped with an external zener diode. The UVLO pin should not
be left floating. The values of RUV1 and RUV2 can be determined from Equation 1 and Equation 2.
VHYS
RUV2
ª: º
10$ ¬ ¼
(1)
1.2V u RUV2
RUV1
ª: º
VIN(STARTUP) 1.2V ¬ ¼
(2)
where
•
•
VHYS is the desired UVLO hysteresis
VIN(STARTUP) is the desired startup voltage of the regulator during turn-on.
Typical shutdown voltage during turn-off can be calculated as follows:
VIN(SHUTDOWN) VIN(STARTUP) VHYS [V]
(3)
High Voltage VCC Regulator
The LM5121 contains an internal high voltage regulator that provides typical 7.6 V VCC bias supply for the
controller and N-channel MOSFET drivers. The input of the VCC regulator, VIN can be connected to a voltage
source as high as 65 V. The VCC regulator turns on when the UVLO pin voltage is greater than 0.4 V. When the
input voltage is below the VCC setpoint level, the VCC output tracks VIN with a small dropout voltage. The
output of the VCC regulator is current limited at 50 mA minimum.
Upon power-up, the VCC regulator sources current into the capacitor connected to the VCC pin. The
recommended range for the VCC capacitor is 1.0 μF to 47 μF and it is recommended to be at least 10 times
greater than CBST value. When operating with a VIN voltage less than 6 V, the value of VCC capacitor should be
4.7 µF or greater.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
13
LM5121/LM5121-Q1
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
www.ti.com
The internal power dissipation of the LM5121 device can be reduced by supplying VCC from an external supply.
If an external VCC bias supply exists and the voltage is greater than 9 V and below 14.5 V. The external VCC
bias supply can be applied to the VCC pin directly through a diode, as shown in Figure 19.
External
VCC
VCC Supply
LM5121
CVCC
Figure 19. External Bias Supply when 9 V<VEXT<14.5 V
Shown in Figure 20 is a method to derive the VCC bias voltage with an additional winding on the boost inductor.
This circuit must be designed to raise the VCC voltage above VCC regulation voltage to shut off the internal VCC
regulator.
VCC
+
nuVOUT
nuVIN
+
+
nu(VOUT -VIN)
1:n
VIN
VOUT
+
+
Figure 20. External Bias Supply using Transformer
The VCC regulator series pass transistor includes a diode between VCC and VIN, as shown in Figure 21, that
should not be forward biased in normal operation. If the voltage of the external VCC bias supply is greater than
the VIN pin voltage, an external blocking diode is required from the input power supply to the VIN pin to prevent
the external bias supply from passing current to the input supply through VCC. The need for the blocking diode
should be evaluated for all applications when the VCC is supplied by the external bias supply. When the input
power supply voltage is less than 4.5 V, an external VCC supply should be used and the external blocking diode
is required.
VIN
VIN
LM5121
External
VCC Supply
VCC
Figure 21. VIN Configuration when VVIN<VVCC
14
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
LM5121/LM5121-Q1
www.ti.com
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
Oscillator
The LM5121 switching frequency is programmable by a single external resistor connected between the RT pin
and the AGND pin. The resistor should be located very close to the device and connected directly to the RT and
AGND pin. To set a desired switching frequency (fSW), the resistor value can be calculated from Equation 4.
9 u 109
ª: º
fSW ¬ ¼
RT
(4)
Slope Compensation
For duty cycles greater than 50%, peak current mode regulators are subject to sub-harmonic oscillation. Subharmonic oscillation is normally characterized by alternating wide and narrow duty cycles. This sub-harmonic
oscillation can be eliminated by a technique, which adds an artificial ramp, known as slope compensation, to the
sensed inductor current.
Additional slope
tON
Sensed Inductor Current
= ILIN u RS u10
Figure 22. Slope Compensation
The slope compensation of the LM5121 is programmable by a single resistor connected between the SLOPE pin
and the AGND pin. The amount of slope compensation can be calculated as follows:
6 x109
xD
fSW x RSLOPE
VSLOPE
[V]
where
D
•
1
VIN
VOUT
(5)
RSLOPE value can be determined from the following equation at minimum input voltage:
LIN u 6 u 109
ª¬: º¼
ªK u VOUT VIN(MIN) º u RS u 10
¬
¼
RSLOPE
where
•
K=0.82~1 as a default
(6)
From the above equation, K can be calculated over the input range as follows:
K
§
LIN u 6 u 109
¨1 ¨
VIN u RS u 10 u RSLOPE
©
·
¸ u D'
¸
¹
where
D'
•
VIN
VOUT
(7)
In any case, K should be greater than 0.5. At higher switching frequency over 500 kHz, the K factor is
recommended to be greater than or equal to 1 because the minimum on-time affects the amount of slope
compensation due to internal delays.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
15
LM5121/LM5121-Q1
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
www.ti.com
The sum of sensed inductor current and slope compensation should be less than COMP output high voltage
(VOH) for proper startup with load and proper current limit operation. This limits the minimum value of RSLOPE to
be:
RSLOPE !
•
·
¸ ª¬: º¼
¸
¹
This equation can be used in most cases
RSLOPE !
•
VIN MIN
5.7 u 109 §
u ¨ 1.2 ¨
fSW
VOUT
©
8 u 109
ª: º
fSW ¬ ¼
This conservative selection should be considered when VIN(MIN) < 5.5 V
The SLOPE pin cannot be left floating.
Error Amplifier
The internal high-gain error amplifier generates an error signal proportional to the difference between the FB pin
voltage and the internal precision 1.2 V reference. The output of the error amplifier is connected to the COMP pin
allowing the user to provide a Type 2 loop compensation network.
RCOMP, CCOMP and CHF configure the error amplifier gain and phase characteristics to achieve a stable voltage
loop. This network creates a pole at DC, a mid-band zero (fZ_EA) for phase boost, and a high frequency pole
(fP_EA). The minimum recommended value of RCOMP is 2 kΩ (See the Feedback Compensation section).
1
fZ _ EA
ªHz º
2S u RCOMP u CCOMP ¬ ¼
(9)
fP _ EA
1
§ CCOMP u CHF
2S u RCOMP u ¨
© CCOMP CHF
·
¸
¹
ª¬Hz º¼
(10)
PWM Comparator
The PWM comparator compares the sum of sensed inductor current and slope compensation ramp to the
voltage at the COMP pin through a 1.2 V internal COMP to PWM voltage drop and terminates the present cycle
when the sum of sensed inductor current and slope compensation ramp is greater than VCOMP –1.2 V.
ILIN
RS
CSP
CSN
+
CS A=10
AMP
RSLOPE
SLOPE
Generator
VOUT
REF
+
+
-
+
PWM
Comparator
RFB2
1.2 V
FB
Error
Amplifier
COMP
RCOMP
CCOMP
RFB1
CHF (optional)
Type 2 Compensation Components
Figure 23. Feedback Configuration and PWM Comparator
16
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
LM5121/LM5121-Q1
www.ti.com
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
Disconnection Switch Control
Soft turn-on is achieved by slowly turning on the disconnection switch. When the UVLO pin voltage is greater
than 1.2 V UVLO threshold and the VCC voltages exceeds the VCC UV threshold, the internal charge pump at
DG starts sourcing current which enhances N-channel MOSFET disconnection switch. The internal charge pump
provides bias voltage at DG pin above VIN pin voltage.
Additional inrush current limiting helps to limit the maximum inrush current. In the inrush current limiting condition
when the voltage across sense resistor RS reaches the inrush current limit threshold, the DG pin voltage is
controlled to limit the current flow in RS by controlling DG pull-down current sink.
As the source voltage of the disconnection switch is charged during initial charging period, the operating point of
the disconnection switch transitions from an active region into the ohmic region and the DG pin voltage is
maintained by the charge pump. An internal 10 µA soft-start current source turns on when the DG to DS voltage
is greater than VGS detection threshold. VIN voltage is recommended to be greater than or equal to the input
power supply voltage because the internal charge pump provides the DG bias voltage above the VIN voltage.
The DG pin voltage is clamped to approximately 16 V above the DS pin and 11 V above the VIN pin by internal
zener diodes.
Standby
Shut down
1.2V
UVLO
0.4V
VCC UV Threshold
VCC
TURN-ON
VGS
VGS Detection
Threshold
TURN-OFF
Inrush
current
limit
VGS Detect
10µA
current
source
1.2V
SS
LO
HO-SW
VIN
tSS
VOUT
Startup Delay
Figure 24. Start-Up Sequence
Hiccup Mode Short Circuit / Overload Protection
If cycle-by-cycle current limit or inrush current limit is reached during any cycle, a 30 μA RES current is sourced
into the RES capacitor for the remainder of the clock cycle. If the RES capacitor voltage exceeds the 1.2 V
restart threshold, a hiccup mode protection sequence is initiated. In the hiccup mode, the DG pin is discharged to
GND if the inrush current limit is reached, the SS capacitor is discharged to GND, both LO and HO outputs are
disabled, and the voltage on the RES capacitor is ramped up and down between 2 V and 4 V eight times.
After the eighth RES pin cycle, the DG pin is released and charged by the DG charge pump. If a 2~3 V zener
diode is connected in parallel with the RES capacitor, the regulator enters into the hiccup mode and never
restarts until UVLO shutdown is cycled. Connect the RES pin directly to the AGND when the hiccup mode
operation is not required.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
17
LM5121/LM5121-Q1
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
www.ti.com
IRES = 10µA
IRES = -5µA
4V
2.0V
1.2V
tCount to Eightt
RES
IRES = 30µA
Restart Delay tRD
tHiccup Mode Off-time tRESt
SS
HO
LO
VGS-DET
VDG-DS
Figure 25. Hiccup Mode Short Circuit Protection
(Start-Up With Output Short)
IRES = 10µA
IRES = -5µA
4V
2.0V
1.2V
RES
tCount to Eightt
IRES = 30µA
Restart Delay tRD
SS
tHiccup Mode Off-time tRESt
HO
LO
VDG-DS
VGS-DET
DG Pull-down when Inrush
Current Limit is Reached
Figure 26. Hiccup Mode Overload Protection (Overload After Start-Up)
Soft-Start
The soft-start feature helps the regulator gradually reach the steady state operating point, thus reducing startup
stresses and surges. The LM5121 regulates the FB pin to the SS pin voltage or the internal 1.2 V reference,
whichever is lower. The internal 10 μA soft-start current source gradually increases the voltage on an external
soft-start capacitor connected to the SS pin. This results in a gradual rise of the output voltage starting from the
input voltage level to the target output voltage. The soft-start time (tSS) varies with the input supply voltage and
output set point and is calculated from Equation 11.
CSS u 1.2V §
V ·
u ¨ 1 IN ¸ ª¬sec º¼
tSS
10$
9OUT ¹
©
(11)
18
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
LM5121/LM5121-Q1
www.ti.com
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
When UVLO pin voltage is greater than 1.2 V UVLO threshold, VCC voltage exceeds the VCC UV threshold and
DG to DS voltage is greater than VGS detection threshold, an internal 10 μA soft-start current source turns on. At
the beginning of this soft-start sequence, VSS should be allowed to fall down below 25 mV by the internal SS pulldown switch. The SS pin can be pulled down by an external switch to stop switching, but pulling up to enable
switching is not recommended. The startup delay (see Figure 24) should be long enough for the high-side boot
capacitor to be fully charged by the internal BST charge pump. This defines the recommended minimum CSS
value, which is especially important when VVIN is greater than 9 V.
§V
·
CSS ! 0.33 u CBST u ¨ OUT ¸ ª¬F º¼
© VVIN ¹
(12)
Also, the value of CSS should be large enough to charge the output capacitor during soft-start time.
10$ u 9OUT &OUT
CSS !
u
ªF º
1.2V
IOUT ¬ ¼
(13)
HO and LO Drivers
The LM5121 contains two strong N-channel MOSFET gate drivers and a high-side level shifter to drive the
external N-channel MOSFET switches. The high-side gate driver works in conjunction with an external bootstrap
diode DBST, and bootstrap capacitor CBST. During the on-time of the low-side N-channel MOSFET driver, the SW
pin voltage is approximately 0 V and the CBST is charged from VCC through the DBST. A 0.1 μF or larger ceramic
capacitor, connected with short traces between the BST and SW pin, is recommended.
The LO and HO outputs are controlled with an adaptive dead-time methodology which ensures that both outputs
are never enabled at the same time. When the controller commands LO to be enabled, the adaptive dead-time
logic first disables HO and waits for HO-SW voltage to drop. LO is then enabled after a small delay (HO Fall to
LO Rise Delay). Similarly, the HO turn-on is delayed until the LO voltage has discharged. HO is then enabled
after a small delay (LO Fall to HO Rise Delay). This technique ensures adequate dead-time for any size Nchannel MOSFET or parallel MOSFET configurations especially when VCC is supplied by a higher external
voltage source. Use caution when adding series gate resistors, as this may decrease the effective dead-time.
Care should be exercised in selecting the N-channel MOSFET devices threshold voltage when the VIN voltage
range is below the VCC regulation level or a bypass operation is required. If bypass operation is required when
output voltage is less than 12 V, a logic level device should be selected for the high-side N-channel MOSFET.
During startup at low input voltages, the low-side N-channel MOSFET's gate plateau voltage should be
sufficiently low to completely enhance the N-channel MOSFET device. If the low-side MOSFET drive voltage is
lower than the low-side MOSFET gate plateau voltage during startup, the regulator may not start properly and it
may operate at the maximum duty cycle in a high power dissipation state. This condition can be avoided by
selecting a lower threshold N-channel MOSFET or by increasing VIN(STARTUP) with the UVLO pin programming.
MODE Control (Forced PWM Mode and Diode Emulation Mode)
A fully synchronous boost regulator implemented with a high-side MOSFET rather than a diode has the capability
to sink current from the output in conditions such as light load, overvoltage or load transient. The LM5121 can be
configured to operate in either forced PWM mode or diode emulation mode.
In forced PWM mode (FPWM), reverse current flow in high-side N-channel MOSFET switch is allowed and the
inductor current conducts continuously at light or no load conditions. The benefit of the forced PWM mode is fast
light load to heavy load transient response and constant frequency operation at light or no load conditions. To
enable forced PWM mode, connect the MODE pin to VCC or tie it to a voltage greater than 1.2 V. In the FPWM
mode, reverse current flow is not limited.
In the diode emulation mode, current flow in the high-side switch is only permitted in one direction (source to
drain). Turn-on of the high-side switch is allowed if the CSP to CSN voltage is greater than the 7 mV rising
threshold of the zero current detection circuit during low-side switch on-time. If the CSP to CSN voltage is less
than 6 mV falling threshold of the zero current detection during high-side switch on-time, reverse current flow
from output to input through the high-side N-channel MOSFET is prevented and discontinuous conduction mode
of operation is enabled by latching off the high-side N-channel MOSFET switch for the remainder of the PWM
cycle. A benefit of the diode emulation is lower power loss at light load conditions.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
19
LM5121/LM5121-Q1
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
www.ti.com
1.2 V
COMP
+
-
40mV
Hysteresis
1.2V
MODE
SkipCycle
+
700k
Default
150mV
20mV
+
Skip Cycle
Comparator
1.2V
100k
+
-
Diode
Emulation
Figure 27. MODE Selection
During startup the LM5121 forces diode emulation, to support startup into a pre-biased load, until the SS pin
voltage exceeds 1.2 V. Forced diode emulation is terminated by a pulse from PWM comparator when SS is
greater than 1.2 V. If there are no LO pulses during the soft-start period, a 350 ns one-shot LO pulse is forced at
the end of soft-start to help charge the bootstrap capacitor. Due to the internal current sense delay, configuring
the LM5121 for diode emulation mode should be carefully evaluated if the inductor current ripple ratio is high and
the controller is operated at very high switching frequency. The transient performance during full load to no load
in FPWM mode should also be verified.
MODE Control (Skip Cycle Mode and Pulse Skipping Mode)
Light load efficiency of the regulator typically drops as the losses associated with switching and bias currents of
the converter become a significant percentage of the total power delivered to the load. In order to increase the
light load efficiency the LM5121 provides two types of light load operation in diode emulation mode.
The skip cycle mode integrated into the LM5121 controller reduces switching losses and improves efficiency in
light load conditions by reducing the average switching frequency. Skip cycle operation is achieved by the skip
cycle comparator. When a light load condition occurs, the COMP pin voltage naturally decreases, reducing the
peak current delivered by the regulator. During COMP voltage falling, the skip cycle threshold is defined as
VMODE –20 mV and during COMP voltage rising, it is defined as VMODE +20 mV. There is 40mV of internal
hysteresis in the skip cycle comparator.
When the voltage at PWM comparator input falls below VMODE –20 mV, both HO and LO outputs are disabled.
The controller continues to skip switching cycles until the voltage at PWM comparator input increases to VMODE
+20 mV, demanding more inductor current. The number of cycles skipped depends upon the load and the
response time of the frequency compensation network. The internal hysteresis of skip cycle comparator helps to
produce a long skip cycle interval followed by a short burst of pulses. An internal 700 kΩ pull-up and 100 kΩ pulldown resistor sets the MODE pin to 0.15 V as a default. Since the peak current limit threshold is set to 750 mV,
the default skip threshold corresponds to approximately 17% of the peak level. In practice the skip level will be
lower due to the added slope compensation. By adding an external pull-up resistor from MODE to the SLOPE or
VCC pin or adding an external pull-down resistor to the ground, the skip cycle threshold can be programmed.
Because the skip cycle comparator monitors the PWM comparator input which tracks the COMP voltage, skip
cycle operation is not recommended when the bypass operation is required.
Pulse skipping operation can be achieved by connecting the MODE pin to ground. The negative 20 mV offset at
the positive input of skip cycle comparator ensures the skip cycle comparator will not be triggered in normal
operation. At light or no load conditions, the LM5121 skips LO pulses if the pulse width required by the regulator
is less than the minimum LO on-time of the device. Pulse skipping appears as a random behavior as the error
amplifier attempts to find the proper pulse width to maintain regulation at light or no load conditions.
Bypass Operation (VOUT = VIN)
The LM5121 allows 100% duty cycle operation for the high-side synchronous switch when the input supply
voltage is equal to or greater than the target output voltage. An internal 200 μA BST charge pump maintains
sufficient high-side driver supply voltage to keep the high-side N-channel MOSFET switch on without the power
stage switching. The internal BST charge pump is enabled when the UVLO pin voltage is greater than 1.2 V, the
VCC voltage exceeds the VCC UV threshold and DG to DS voltage is greater than the VGS detection threshold.
20
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
LM5121/LM5121-Q1
www.ti.com
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
The BST charge pump generates 5.3 V minimum BST to SW voltage when SW voltage is greater than 9 V. This
requires minimum 9 V boost output voltage for proper bypass operation. The leakage current of the boot diode
should be always less than the BST charge pump sourcing current to maintain a sufficient driver supply voltage
at both low and high temperatures. Forced PWM mode is the recommended PWM configuration when bypass
operation is required.
Cycle-by-Cycle Current Limit
The LM5121 features a peak cycle-by-cycle current limit function. If the CSP to CSN voltage exceeds the 75 mV
cycle-by-cycle current limit threshold, the current limit comparator immediately terminates the LO output.
For the case where the inductor current overshoots the desired limit, such as inductor saturation, the current limit
comparator blocks LO pulses until the current has decayed below the current limit threshold. Peak inductor
current in current limit can be calculated as follows:
75mV
IPEAK(CL)
ªA º
RS ¬ ¼
(14)
Circuit Breaker Function
In addition to the hiccup mode short circuit / overload protection, LM5121 provides a circuit breaker function for
maximum safety. If the input current increases rapidly due to a fault, the current through the disconnection switch
may exceed the inrush control threshold before the inrush control loop is able to respond. If the sensed current
exceeds the circuit breaker threshold, the disconnection switch is quickly turned off through an internal switch at
the DG pin until current sense input falls below the circuit breaker disable threshold. If the RES pin voltage is
less than 1.2 V, the controller then restarts the inrush control procedure.
Clock Synchronization
The SYNCIN/RT pin can be used to synchronize the internal oscillator to an external clock. The positive going
synchronization clock at the RT pin must exceed the RT sync rising threshold and the negative going
synchronization clock at RT pin must exceed the RT sync falling threshold to trip the internal synchronization
pulse detector.
With the configuration in Figure 28, the frequency of the external synchronization pulse is recommended to be
within +/–20% of the internal oscillator frequency programmed by RT resistor. The actual operating range is +/–
100/40% of the programmed frequency. For example, 900 kHz external synchronization clock and 20 kΩ RT
resistor are required for 450 kHz switching. The internal oscillator can be synchronized by AC coupling a positive
edge into the RT pin. A 5 V amplitude pulse signal coupled through 100 pF capacitor is a good starting point.
The RT resistor is always required in this configuration, whether the oscillator is free running or externally
synchronized.
Care should be taken to guarantee that the RT pin voltage does not go below –0.3 V at the falling edge of the
external pulse. This may limit the duty cycle of external synchronization pulse. There is approximately 400 ns
delay from the rising edge of the external pulse to the rising edge of LO.
fSYNC
SYNCIN/RT
CSYNC
RT
LM5121
Figure 28. Oscillator Synchronization Through AC Coupling
With the configuration in Figure 29, the internal oscillator can be synchronized by connecting the external
synchronization clock to the RT pin through the RT resistor with free of the duty cycle limit. The output stage of
the external clock source should be a low impedance totem-pole structure and the default logic state of fSYNC
should be low.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
21
LM5121/LM5121-Q1
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
www.ti.com
fSYNC
SYNCIN/RT
RT
LM5121
Figure 29. Oscillator Synchronization Through a Resistor
Maximum Duty Cycle
When operating with a high PWM duty cycle, the low-side N-channel MOSFET device is forced off each cycle.
This forced LO off-time limits the maximum duty cycle of the controller. When designing a boost regulator with
high switching frequency and high duty cycle requirements, check the required maximum duty cycle. The
minimum input supply voltage which can achieve the target output voltage is estimated from Equation 15 .
VIN(MIN) fSW u VOUT u (750ns margin) [V]
(15)
100 ns of margin is recommended.
Thermal Protection
Internal thermal shutdown circuitry is provided to protect the controller in the event the maximum junction
temperature is exceeded. When activated, typically at 165°C, the controller is forced into a low-power shutdown
mode, disabling the output drivers, disconnection switch and the VCC regulator. This feature is designed to
prevent overheating and destroying the device.
22
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
LM5121/LM5121-Q1
www.ti.com
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
APPLICATION INFORMATION
Feedback Compensation
The open loop response of a boost regulator is the product of the modulator transfer function and the feedback
transfer function. When plotted on a dB scale, the open loop gain is shown as the sum of modulator gain and
feedback gain. The modulator transfer function of a current mode boost regulator including a power stage
transfer function with an embedded current loop can be simplified as one pole, one zero and one Right Half
Plane (RHP) zero system.
Modulator transfer function is defined as follows:
§
· §
s
s
¨1 ¸ u ¨1 ¨
¸
¨
Ö
&
&
VOUT (s)
Z _ ESR ¹ ©
Z _ RHP
AM u ©
Ö
§
VCOMP (s)
s ·
¨1 ¸
¨ &P _ LF ¸
©
¹
·
¸
¸
¹
where
RLOAD
D'
u
RS _ EQ u A S 2
AM (Modulator DC gain)
•
•
&P _ LF /RDG SROH
2
RLOAD u COUT
&Z _ ESR (65]HUR
1
RESR u COUT
&Z _ RHP 5+3]HUR
RLOAD u (D' )2
LIN _ EQ
•
•
•
•
LIN _ EQ
LIN
, RS _ EQ
n
RS
n
n is the number of the phase.
(16)
If the ESR of COUT (RESR) is small enough and the RHP zero frequency is far away from the target crossover
frequency, the modulator transfer function can be further simplified to one pole system and the voltage loop can
be closed with only two loop compensation components, RCOMP and CCOMP, leaving a single pole response at the
crossover frequency. A single pole response at the crossover frequency yields a very stable loop with 90 degrees
of phase margin.
The feedback transfer function includes the feedback resistor divider and loop compensation of the error
amplifier. RCOMP, CCOMP and optional CHF configure the error amplifier gain and phase characteristics, and create
a pole at origin, a low frequency zero and a high frequency pole.
The feedback transfer function is defined as follows:
s
1
&Z _ EA
VÖ COMP
AFB u
§
VÖ OUT
s ·
s u ¨1 ¸
¨
&P _ EA ¸¹
©
where
AFB (Feedback DC gain)
•
•
1
RFB2 u CCOMP CHF
&Z _ EA /RZIUHTXHQF\]HUR
&P _ EA +LJKIUHTXHQF\SROH
•
1
RCOMP u CCOMP
1
RCOMP u CHF
(17)
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
23
LM5121/LM5121-Q1
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
www.ti.com
The pole at the origin minimizes output steady state error. The low frequency zero should be set to cancel the
load pole of the modulator. The high frequency pole can be used to cancel the zero created by the output
capacitor ESR or to decrease noise susceptibility of the error amplifier. By placing the low frequency zero an
order of magnitude less than the crossover frequency, the maximum amount of phase boost is achieved at the
crossover frequency. The high frequency pole should be set above the crossover frequency since the addition of
CHF adds a pole in the feedback transfer function.
The crossover frequency (open loop bandwidth) is usually selected between one twentieth and one fifth of the
switching frequency. In a simplified formula, the estimated crossover frequency can be defined as:
RCOMP
fCROSS
u D' [Hz]
S u RS _ EQ u RFB2 u A S u COUT
where
D'
•
VIN
VOUT
(18)
For higher crossover frequency, RCOMP can be increased, while proportionally decreasing CCOMP. Conversely,
decreasing RCOMP while proportionally increasing CCOMP, results in lower bandwidth while keeping the same zero
frequency in the feedback transfer function.
The modulator transfer function can be measured using a network analyzer and the feedback transfer function
can be configured for the desired open loop transfer function. If the network analyzer is not available, step load
transient tests can be performed to verify acceptable performance. The step load goal is minimum
overshoot/undershoot with a damped response.
Sub-Harmonic Oscillation
Peak current mode regulator can exhibit unstable behavior when operating above 50% duty cycle. This behavior
is known as sub-harmonic oscillation and is characterized by alternating wide and narrow pulses at the SW pin.
Sub-harmonic oscillation can be prevented by adding a voltage ramp (slope compensation) on top of the sensed
inductor current. By choosing K≥0.82~1.0, the sub-harmonic oscillation will be eliminated even with widely
varying input voltage.
In time-domain analysis, the steady-state inductor current starting from an initial point returns to the same point.
When the amplitude of an end cycle current error (dI1) caused by an initial perturbation (dI0) is less than the
amplitude of dI0 or dI1/dI0 > –1, the perturbation naturally disappears after a few cycles. When dl1/dl0<-1, the
initial perturbation no longer disappear, it results in sub-harmonic oscillation in the steady-state.
Steady-State
Inductor Current
dI0
tON
dI1
Inductor Current with
Initial Perturbation
Figure 30. Effect of Initial Perturbation when dl1/dl0 < -1
dI1/dI0 can be calculated as:
dI1
1
1
dI0
K
(19)
The relationship between dI1/dI0 and K factor is illustrated graphically below.
24
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
LM5121/LM5121-Q1
www.ti.com
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
Figure 31. dl1/dl0 vs K Factor
The absolute minimum value of K is 0.5. When K<0.5, the amplitude of dl1 is greater than the amplitude of dl0
and any initial perturbation results in sub-harmonic oscillation. If K=1, any initial perturbation will be removed in
one switching cycle. This is known as one-cycle damping. When -1<dl1/dl0<0, any initial perturbation will be
under-damped. Any perturbation will be over-damped when 0<dl1/dl0<1.
In the frequency-domain, Q, the quality factor of sampling gain term in modulator transfer function, is used to
predict the tendency for sub-harmonic oscillation, which is defined as:
1
Q
S K 0.5
(20)
The relationship between Q and K factor is illustrated in Figure 32
Figure 32. Sampling Gain Q vs K Factor
The recommended absolute minimum value of K is 0.5. High gain peaking when K is less than 0.5 results in subharmonic oscillation at fSW/2. A higher value of K factor may introduce additional phase shift near the crossover
frequency, but has the benefit of reducing noise susceptibility in the current loop. The maximum allowable value
of K factor can be calculated using the maximum crossover frequency equation and frequency analysis formulas
in Table 1.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
25
LM5121/LM5121-Q1
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
www.ti.com
Table 1. BOOST REGULATOR FREQUENCY ANALYSIS
SIMPLIFIED FORMULA
MODULATOR TRANSER
FUNCTION
Modulator DC gain
RHP zero
VÖ OUT (s)
Ö
V
(s)
COMP
COMPREHENSIVE FORMULA
§
· §
s
s
¨1 ¸ u ¨1 ¨
¸ ¨
Z
ZZ _ RHP
Z _ ESR ¹ ©
©
AM u
§
s ·
¨1 ¸
¨
ZP _ LF ¸¹
©
(2)
·
¸
¸
¹
VÖ OUT s
Ö
VCOMP s
1
RESR u COUT
&Z _ ESR
ESR pole
Not considered
Dominant load pole
&P _ LF
&Z _ ESR
1
RESR1 u COUT1
&P _ ESR
1
RESR1 u COUT1 / /COUT2
2
RLOAD u COUT
&P _ HF
Sampled gain inductor pole
Not considered
Sub-harmonic double pole
K factor
Not considered
Not considered
K=1
VÖ
(s)
COMP
VÖ
(s)
Q
1
S K 0.5
&n
&SW
2
S u ISW
fn
fSW
2
K
§
LIN u 6 u 109
¨1 ¨
V
u
IN RS u 10 u RSLOPE
©
1
AFB u
OUT
AFB
Feedback DC gain
Mid-band Gain
Low frequency zero
&Z _ EA
1
RCOMP u CHF
·
¸ u D'
¸
¹
s
&Z _ EA
§
s
s u ¨1 ¨
&
P
_ EA
©
·
¸
¸
¹
1
RFB2 u (CCOMP CHF )
AFB _ MID
&P _ EA
4 u &n
or
FEEDBACK TRANSFER
FUNCTION
High frequency pole
fSW
K 0.5
or
&P _ HF
Quality factor
·
¸
¸
¹
RLOAD u (D')2
LIN _ EQ
&Z _ RHP
ESR zero
§
s
¨1 ¨
&P_LF
©
§
s · §
s ·
¨1 ¸ u ¨1 ¸
¨
&ZESR ¸ ¨© &ZRHP ¸¹
©
¹
· §
· §
s
s
s2
2
¸ u ¨1 ¸ u ¨1 ¸ ¨
¸
¨
&
&
&n
p _ ESR ¹ ©
P_HF
¹ ©
RLOAD
D'
u
RS _ EQ u A S 2
AM
(2)
AM u
(1)
RCOMP
RFB2
1
RCOMP u CCOMP
ZP _ EA
1
RCOMP u CCHF / /CCOMP
(1)
Comprehensive equation includes an inductor pole and a gain peaking at fSW/2, which is caused by sampling effect of the current mode
control. Also, it assumes that a ceramic capacitor COUT2 (No ESR) is connected in parallel with COUT1. RESR1 represents ESR of COUT1.
(2)
With multiphase configuration,
number of phases.
26
LIN _ EQ
LIN
RS _ EQ
n ,
RS R
LOAD
n ,
VOUT
IOUT of each phase u n ,
and COUT = COUT of each phase x n, where n =
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
LM5121/LM5121-Q1
www.ti.com
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
Table 1. BOOST REGULATOR FREQUENCY ANALYSIS (continued)
SIMPLIFIED FORMULA
§
· §
s
s
¨1 ¸ u ¨1 ¨ &Z _ ESR ¸ ¨ &Z _ RHP
©
¹
©
AM u AFB u
§
s ·
¨1 ¸
¨ &P _ LF ¸
©
¹
OPEN LOOP RESPONSE
T s
Crossover frequency (3)
(Open loop band width)
fCROSS
·
¸
¸
¹u
COMPREHENSIVE FORMULA
1
s
&Z _ EA
§
s
s u ¨1 ¨ &P _ EA
©
RCOMP
u D'
S u RS _ EQ u RFB2 u A S u COUT
·
¸
¸
¹
§
· §
·
s
s
¨1 ¸ u ¨1 ¸
¨
&Z _ ESR ¸¹ ¨© &Z _ RHP ¸¹
©
AM u AFB u
§
· §
s · §
s
s
s2
¨1 ¸ u ¨1 ¸ u ¨1 ¨
&P _ LF ¸¹ ¨©
&p _ ESR ¸¹ ¨©
&PHF &n2
©
T s
fSW &Z _RHP
or
whichever is smaller
5
2u Su 4
fCROSS _MAX
1
·
¸
¸
¹
u
s
&Z _ EA
§
s
s u ¨1 ¨
&P _ EA
©
·
¸
¸
¹
Use graphic tool
fCROSS _MAX
Maximum cross over
frequency (4)
(1)
fSW §
u ¨ 1 4 u Q2 1 ·¸
¹
4uQ ©
or
&Z _ RHP
2u Su 4
, whichever is smaller
(3)
(4)
f
&Z _ RHP
CCOMP
RLOAD u COUT
D'
4 u RCOMP , and
Assuming &Z _ EA &P _ LF, &P _ EA &Z _ ESR, CROSS 2 u S u 10 ,
The frequency at which 45º phase shift occurs in modulator phase characteristics.
VIN
VOUT .
Output Overvoltage Protection
Output overvoltage protection can be achieved by adding a simple external circuit. The output overvoltage
protection circuit shown in Figure 33 shuts down the LM5121 when the output voltage exceeds the overvoltage
threshold set by the zener diode.
VOUT
LM5121
UVLO
Figure 33. Output Overvoltage Protection
Input Transient Suppression
Input over-voltage transient suppression can be achieved by adding a zener diode from DG to ground. The DS
voltage will be clamped to the zener voltage minus the gate threshold voltage of the disconnection MOSFET
switch.
Since the input clamping occurs in the active region of disconnection MOSFET switch, safe operating area and
the thermal properties of the disconnection MOSFET switch should be carefully considered.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
27
LM5121/LM5121-Q1
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
www.ti.com
V SUPPLY
V OUT
+
BST
VCC
DS
SW
LO
DG
HO
COMP
CSN
FB
CSP
RES
VIN
UVLO
SS
MODE
PGND
AGND
SLOPE
SYNCIN/RT
LM5121
Figure 34. Input Transient Suppression
Inrush Current Limit Programming
Inrush current limit level can be lower than the cycle-by-cycle current limit level by adding a simple external
circuit. The external inrush current limit programming circuit shown in Figure 35 and Figure 36 pull down CSN pin
during inrush current limiting. Also, this configuration enables latch-off mode circuit breaker.
ILIN
CSN
100 k
CSP
RINRUSH
100
100
RS
VCC
SLOPE
1.2Vth
NMOS
Figure 35. Inrush Current Limit Programming #1
ILIN
RINRUSH
CSN
VCC
100 k
CSP
100
100
RS
SLOPE
Figure 36. Inrush Current Limit Programming #2
28
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
LM5121/LM5121-Q1
www.ti.com
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
VIN
500k
Reverse Battery Protection + Disconnect Switch Control
Signal
PMOS
Power
NMOS
DG
VOUT
DS
+
+
VCC
DS
BST
SW
LO
DG
HO
CSN
COMP
CSP
FB
VIN
RES
SS
UVLO
SLOPE
SYNCIN/RT
LM5121
MODE
PGND
AGND
VIN
500k
Figure 37. Reverse Battery Protection + Disconnection Switch
Signal
PMOS
Power
NMOS
VOUT
+
500k
100pF
+
VCC
DS
BST
DG
CSN
SW
LO
HO
COMP
CSP
FB
VIN
RES
UVLO
SLOPE
SYNCIN/RT
LM5121
SS
MODE
PGND
AGND
Figure 38. Reverse Battery Protection
PC Board Layout Recommendation
In a boost regulator, the primary switching loop consists of the output capacitor and N-channel MOSFET power
switches. Minimizing the area of this loop reduces the stray inductance and minimizes noise. Especially, placing
high quality ceramic output capacitors as close to this loop earlier than bulk aluminum output capacitors
minimizes output voltage ripple and ripple current of the aluminum capacitors.
In order to prevent a dv/dt induced turn-on of high-side switch, HO and SW should be connected to the gate and
source of the high-side synchronous N-channel MOSFET switch through short and low inductance paths. In
FPWM mode, the dv/dt induced turn-on can occur on the low-side switch. LO and PGND should be connected to
the gate and source of the low-side N-channel MOSFET through short and low inductance paths. All of the
power ground connections should be connected to a single point. Also, all of the noise sensitive low power
ground connections should be connected together near the AGND pin and a single connection should be made
to the single point PGND. CSP and CSN are high impedance pins and noise sensitive. CSP and CSN traces
should be routed together with kelvin connections to the current sense resistor as short as possible. If needed,
place 100 pF ceramic filter capacitor as close to the device. MODE pin is also high impedance and noise
sensitive. If an external pull-up or pull-down resistor is used at MODE pin, the resistor should be placed as close
the device. VCC, VIN and BST capacitor must be as physically close as possible to the device.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
29
LM5121/LM5121-Q1
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
www.ti.com
The LM5121 has an exposed thermal pad to aid power dissipation. Adding several vias under the exposed pad
helps conduct heat away from the device. The junction to ambient thermal resistance varies with application. The
most significant variables are the area of copper in the PC board, the number of vias under the exposed pad and
the amount of forced air cooling. The integrity of the solder connection from the device exposed pad to the PC
board is critical. Excessive voids greatly decrease the thermal dissipation capacity. The highest power dissipating
components are the two power switches. Selecting N-channel MOSFET switches with exposed pads aids the
power dissipation of these devices.
30
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
LM5121/LM5121-Q1
www.ti.com
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
Design Example and Component Selection
OPERATING CONDITIONS
● Output Voltage (VOUT)
:
12 V
● Full Load Current (IOUT)
:
2A
● Output Power
:
24 W
● Minimum Input Voltage (VIN(MIN))
:
3 V (5.7 V for start-up)
● Typical Input Voltage (VIN(TYP))
:
9V
● Maximum Input Voltage (VIN(MAX))
:
12 V
● Switching Frequency (fSW)
:
250 kHz
● Disconnection Switch Control
:
Yes
TIMING RESISTOR RT
Generally, higher frequency applications are smaller but have higher losses. Operation at 250 kHz is selected for
this example as a reasonable compromise between small size and high-efficiency. The value of RT for 250 kHz
switching frequency is calculated as follows:
RT
9 u 109
fSW
9 u 109
250 kHz
36.0 k:
(21)
A standard value of 36.5 kΩ is chosen for RT.
UVLO DIVIDER RUV2, RUV1
The desired startup voltage and the hysteresis are set by the voltage divider RUV2, RUV1. The UVLO shutdown
voltage should be high enough to fully enhance the low-side N-channel MOSFET switch. For this design, the
startup voltage is set to 5.5 V which is 0.2 V below 5.7 V. VHYS is set to 3.7 V. This results 1.8 V of VIN(SHUTDOWN).
The values of RUV2, RUV1 are calculated as follows:
VHYS
3.7 V
RUV2
370 k:
IHYS
10 PA
(22)
RUV1
1.2V u RUV2
VIN(STARTUP) 1.2V
1.2V u 370 k:
5.5V 1.2V
103 k:
(23)
A standard value of 365 kΩ is selected for RUV2. RUV1 is selected to be a standard value of 107 kΩ.
INPUT INDUCTOR LIN
The inductor ripple current is typically set between 20% and 40% of the full load current, as a good compromise
between core loss and copper loss of the inductor. Higher ripple current allows a smaller inductor size, but
places more of a burden on the output capacitor to smooth the ripple voltage on the output. For this example, a
ripple ratio (RR) of 0.3, 30% of the input current was chosen. Knowing the switching frequency and the typical
output voltage, the inductor value can be calculated as follows:
LIN
VIN
V ·
1 §
u
u ¨ 1 IN ¸
IIN u RR fSW ©
VOUT ¹
9V
1
9V ·
§
u
u 1
24W
250 kHz ¨© 12V ¸¹
u 0.3
9V
11.3 +
(24)
The closest standard value of 10 μH was chosen for LIN.
The saturation current rating of the inductor should be greater than the peak inductor current, which is calculated
at the minimum input voltage and full load. A 2.7 V startup voltage is used to conservatively estimate the peak
inductor current.
IPEAK
IIN §
VIN
V ·
1
u
u ¨ 1 IN ¸
2 LIN u fSW ©
VOUT ¹
12V u 2A 1
2.7V
§ 2.7V ·
u
u 1
2.7V
2 10 + u N+] ©¨
9 ¹¸
9.3 A
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
(25)
31
LM5121/LM5121-Q1
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
www.ti.com
CURRENT SENSE RESISTOR RS
The peak input current limit threshold should be set 20~50% higher than the required peak current at low input
voltage and full load, accounting for tolerances. For this example, 20% is margin is chosen.
VCS TH1
75 mV
RS
6.7 m :
IPEAK(CL) 9.3A u 1.2
(26)
A closest standard value of 7 mΩ is selected for RS. The maximum power loss of RS is calculated as follows.
PLOSS(RS)
I2R
(9.3A u 1.2)2 u 7m:
0.87W
(27)
CURRENT SENSE FILTER RCSFP, RCSFN, CCS
The current sense filter is optional. 100 pF for CCS and 100 Ω for RCSFP and RCSFN are normal recommendations.
Because CSP and CSN pins are high impedance, CCS should be placed physically as close to the device.
VIN
RCSFN
+
RCSFP
RS
CSN
LM5121
CCS
CSP
Figure 39. Current Sense Filter
SLOPE COMPENSATION RESISTOR RSLOPE
The K value is selected to be 1 at the minimum input voltage. RSLOPE should be selected such that the sum of
sensed inductor current and slope compensation is less than COMP output high voltage.
RSLOPE !
RSLOPE
8 u 109
fSW
8 u 109
250 kHz
LIN u 6 u 10
32 k:
(28)
9
9
ªK u VOUT VIN(MIN) º u RS u 10
¬
¼
10 + u u 1u 12V 3V u 7m: u 10
95 k:
(29)
A closest standard value of 95.3 kΩ is selected for RSLOPE.
OUTPUT CAPACITOR COUT
The output capacitors smooth the output voltage ripple and provide a source of charge during transient loading
conditions. Also the output capacitors reduce the output voltage overshoot when the load is suddenly
disconnected.
The ripple current rating of the output capacitor should be carefully considered. In boost regulator, the output is
supplied by discontinuous current and the ripple current requirement is usually high. In practice, the ripple current
requirement can be dramatically reduced by placing high quality ceramic capacitors closer to the high side
MOSFET switch than the bulk aluminum capacitors.
The output voltage ripple is dominated by the ESR of the output capacitors. Parallel output capacitors are a good
choice to minimize effective ESR and split the output ripple current into multiple capacitors.
In this example, three 330 µF aluminum capacitors are used to share the output ripple current and source the
required charge. The maximum output ripple current can be calculated at the minimum input voltage as follows:
IOUT
2.0A
IRIPPLE _ MAX(COUT)
4A
VIN(MIN)
3V
2
u
2u
12V
VOUT
(30)
32
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
LM5121/LM5121-Q1
www.ti.com
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
Assuming 60 mΩ of ESR per output capacitor, the output voltage ripple at the minimum input voltage is
calculated as follows:
VRIPPLE _ MAX(COUT)
§
·
IOUT
1
u ¨R
¸
VIN(MIN) © ESR 4 u COUT u fSW ¹
VOUT
·
2.0A § 60m:
1
u
¸
3V ¨© 3
4 u 3 u 330 ) u N+] ¹
12V
0.168V
(31)
In practice, four 10 µF ceramic capacitors are additionally placed before the bulk aluminum capacitors to reduce
the output voltage ripple and share the output ripple current.
INPUT CAPACITOR CIN
The input capacitors smooth the input voltage ripple. Assuming high quality ceramic capacitors are used for the
input capacitors, the maximum input voltage ripple which occurs when the input voltage is half of the output
voltage can be calculated as follows:
VOUT
12V
VRIPPLE _ MAX(CIN)
0.045V
32 u LIN u CIN u fSW 2 32 u 10 PH u 4 u 3.3 PF u 250 kHz2
(32)
The value of input capacitor is also a function of source impedance, the impedance of source power supply.
More input capacitor will be required to prevent a chatter condition during power up if the impedance of source
power supply is not low.
VIN FILTER RVIN, CVIN
An R-C filter (RVIN, CVIN) on the VIN pin is optional. It is not required if the CIN capacitors are high quality ceramic
capacitors and placed physically close to the device. The filter helps to prevent faults caused by high frequency
switching noise injection into the VIN pin. A 0.47 μF ceramic capacitor is used this example. Recommended filter
values are 3 Ω for RVIN and 0.47 µF for CVIN . A larger filter with 2.2 µ to 4.7 µF CVIN is recommended when the
input voltage is lower than 8 V or when the required duty cycle is close to the maximum duty cycle limit.
VIN
VIN
RVIN
CVIN
LM5121
Figure 40. VIN Filter
BOOTSTRAP CAPACITOR CBST AND BOOST DIODE DBST
The bootstrap capacitor between the BST and SW pins supplies the gate current to charge the high-side Nchannel MOSFET gate during each turn-on cycle and also supplies recovery charge for the bootstrap diode. The
peak current can be several amperes. The recommended value of the bootstrap capacitor is 0.1 μF. CBST should
be a good quality, low ESR, ceramic capacitor located at the pins of the device to minimize potentially damaging
voltage transients caused by trace inductance. The minimum value for the bootstrap capacitor is calculated as
follows:
QG
CBST
ªF º
û9BST ¬ ¼
(33)
Where QG is the high-side N-channel MOSFET gate charge and ΔVBST is the tolerable voltage droop on CBST,
which is typically less than 5% of VCC or conservatively 0.15 V . In this example, the value of the BST capacitor
(CBST) is 0.1 µF.
The voltage rating of DBST should be greater than the peak SW node voltage plus 16 V. A low leakage diode is
mandatory for bypass operation. The leakage current of DBST should be low enough for the BST charge pump to
maintain a sufficient high-side driver supply voltage at high temperature. A low leakage diode also prevents the
possibility of excessive VCC voltage during shutdown, in high output voltage applications. If the diode leakage is
excessive, a zener clamp or bleed resistor may be required on VCC. High-side driver supply voltage should be
greater than the high-side N-channel MOSFET switch gate plateau at the minimum input voltage.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
33
LM5121/LM5121-Q1
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
www.ti.com
VCC CAPACITOR CVCC
The primary purpose of the VCC capacitor is to supply the peak transient currents of the LO driver and bootstrap
diode as well as to provide stability for the VCC regulator. The peak driver currents can be several amperes. The
value of CVCC should be at least 10 times greater than the value of CBST, and should be a good quality, low ESR,
ceramic capacitor. CVCC should be placed close to the pins of the IC to minimize potentially damaging voltage
transients caused by trace inductance. A value of 4.7 µF was selected for this design example.
OUTPUT VOLTAGE DIVIDER RFB1, RFB2
RFB1 and RFB2 set the output voltage level. The ratio of these resistors is calculated as follows:
VOUT
RFB2
1
RFB1
1.2V
(34)
The ratio between RCOMP and RFB2 determines the mid-band gain, AFB_MID. A larger value for RFB2 may require a
corresponding larger value for RCOMP. RFB2 should be large enough to keep the total divider power dissipation
small. A 49.9 kΩ in series with 681 Ω was chosen for high-side feedback resistors in this example, which results
in a RFB1 value of 5.62 kΩ for 12 V output.
SOFT-START CAPACITOR CSS
The soft-start time (tSS) is the time required for the output voltage set point to reach the target voltage from the
input voltage. The soft-start time is not only proportional to the soft-start capacitor, but also depends on the input
voltage. With 0.1 µF for CSS, the soft-start time is calculated as follows:
VIN(STARTUP) · 0.1 ) u 9 §
CSS u 1.2V §
9 ·
u ¨¨ 1 u ¨1 tSS(MAX)
6.3 msec
¸¸
ISS
V
10
$
9 ¸¹
©
OUT
©
¹
(35)
RESTART CAPACITOR CRES
The restart capacitor determines the restart delay time tRD and hiccup mode off time tRES (see Figure 25). tRD
should be greater than tSS(MAX). The minimum required value of CRES can be calculated at the low input voltage
as follows:
IRES u tSS(MAX) 30 $ u PVHF
CRES(MIN)
0.16 PF
VRES
1.2V
(36)
A standard value of 0.18 µF is selected for CRES.
LOW-SIDE POWER SWITCH QL
Breaking down the various losses is one way to compare the relative efficiencies of different N-channel MOSFET
devices. Losses in the low-side N-channel MOSFET device can be separated into conduction loss and switching
loss.
Low-side conduction loss is approximated calculated as follows:
PCOND(LS)
D u IIN2 u RDS _ ON(LS) u 1.3
§
VIN
¨1 V
OUT
©
2
· § IOUT u VOUT ·
¸u¨
¸ u RDS _ ON(LS) u 1.3 [W]
VIN
¹
¹ ©
(37)
Where D is the duty cycle and the factor of 1.3 accounts for the increase in the N-channel MOSFET device onresistance due to heating. Alternatively, the factor of 1.3 can be eliminated and the high temperature onresistance of the N-channel MOSFET device can be estimated using the RDS(ON) vs temperature curves in the Nchannel MOSFET datasheet.
Switching loss occurs during the brief transition period as the low-side N-channel MOSFET device turns on and
off. During the transition period both current and voltage are present in the channel of the N-channel MOSFET
device. The low-side switching loss is approximated as follows:
PSW(LS) 0.5 u VOUT u IIN u (tR tF ) u fSW [W]
(38)
tR and tF are the rise and fall times of the low-side N-channel MOSFET device. The rise and fall times are usually
mentioned in the N-channel MOSFET datasheet or can be empirically observed with an oscilloscope.
34
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
LM5121/LM5121-Q1
www.ti.com
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
An additional Schottky diode can be placed in parallel with the low-side N-channel MOSFET switch, with short
connections to the source and drain in order to minimize negative voltage spikes at the SW node.
HIGH-SIDE POWER SWITCH QH AND ADDITIONAL PARALLEL SCHOTTKY DIODE
Losses in the high-side N-channel MOSFET device can be separated into conduction loss, dead-time loss and
reverse recovery loss. Switching loss is calculated only for the low-side N-channel MOSFET device. Switching
loss in the high-side N-channel MOSFET device is negligible because the body diode of the high-side N-channel
MOSFET device turns on before and after the high-side N-channel MOSFET switches.
High-side conduction loss is approximated as follows:
2
PCOND(HS)
(1 D) u IIN2 u RDS _ ON(HS) u 1.3
§ VIN · § IOUT u VOUT ·
¨
¸u¨
¸ u RDS _ ON(HS) u 1.3 [W]
VIN
¹
© VOUT ¹ ©
(39)
Dead-time loss is approximated as follows:
PDT(HS) VD x IIN x (tDLH tDHL ) x fSW [W]
where
•
VD is the forward voltage drop of the high-side N-channel MOSFET body diode.
(40)
Reverse recovery characteristics of the high-side N-channel MOSFET strongly influences efficiency, especially
when the output voltage is high. Smaller reverse recovery charge helps to increase the efficiency while also
minimizing switching noise.
Reverse recovery loss is approximated as follows:
PRR(HS) VOUT u QRR u fSW [W]
(41)
where
•
QRR is the reverse recovery charge of the high-side N-channel MOSFET body diode.
(42)
An additional Schottky diode can be placed in parallel with the high-side switch to improve efficiency. Usually, the
power rating of this parallel Schottky diode can be less than the high-side switch ratings because the diode
conducts only during dead-times. The power rating of the parallel diode should be equivalent or higher than highside switch ratings if bypass operation is required, hiccup mode operation is required or a heavy load exists
before the controller begins switching.
SNUBBER COMPONENTS
A resistor-capacitor snubber network across the high-side N-channel MOSFET device reduces ringing and
spikes at the switching node. Excessive ringing and spikes can cause erratic operation and can couple noise to
the output. Selecting the values for the snubber is best accomplished through empirical methods. First, make
sure the lead lengths for the snubber connections are very short. Start with a resistor value between 5 and 50 Ω.
Increasing the value of the snubber capacitor results in more damping, but this also increases snubber losses.
Select a minimum value for the snubber capacitor that provides adequate damping of the spikes on the switch
waveform at heavy load. A snubber may not be necessary with an optimized layout.
Disconnect Switch QD Selection
The N-channel MOSFET disconnection switch (QD) should be selected based on the following criteria:
• The BVDSS rating must be greater than the maximum input voltage, plus ringing and transients.
• The safe operating area (SOA) and the thermal properties should be considered. If required, limit the rise time
of the input power supply or the maximum start-up input voltage.
• Absolute maximum rating of VGS should be greater than 18 V.
• If the minimum VIN voltage is less than 6.5 V, a logic level MOSFET should be used.
• The plateau voltage during inrush current limiting is recommended to be less than VGS-DET. If the VPLATEAU is
greater than VGS-DET, boost switching might start before finishing the inrush limiting.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
35
LM5121/LM5121-Q1
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
www.ti.com
Freewheeling Diode DF Selection
If QD turns off quickly by the circuit breaker function, the inductor current continues flowing through a
freewheeling diode (DF). DF should have enough capability to handle 150 mV/RS of peak current during inductor
current decay and the voltage rating must be greater than the maximum input voltage, plus ringing and
transients. The inductor current decay time is calculated from Equation 43.
LIN u 0.15
tDF
[sec]
RS u (VOUT VIN )
(43)
LOOP COMPENSATION COMPONENTS CCOMP, RCOMP, CHF
RCOMP, CCOMP and CHF configure the error amplifier gain and phase characteristics to produce a stable voltage
loop. For a quick start, follow the 4 steps listed below:
STEP1: Select fCROSS
Select the cross over frequency (fCROSS) at one fourth of the RHP zero or one tenth of the switching frequency
whichever is lower.
fSW
25 kHz
10
(44)
VOUT
VIN 2
)
u(
fZ _ RHP
RLOAD u (D')2
IOUT
VOUT
13.4 kHz
4
4 u 2S u LIN _ EQ
4 u 2S u LIN _ EQ
(45)
A 13.4 kHz crossover frequency is selected. RHP zero at minimum input voltage should be considered if the
input voltage range is wide.
STEP2: Determine required RCOMP
Knowing fCROSS, RCOMP is calculated as follows:
RCOMP
fCROSS u S u RS u RFB2 u 10 u COUT u
VOUT
VIN
200 k:
(46)
A standard value of 200 kΩ is selected for RCOMP
STEP3: Determine CCOMP to cancel load pole. Place the error amplifier zero at twice the load pole frequency.
Knowing RCOMP, CCOMP is calculated as follows:
RLOAD x COUT
CCOMP
7.6nF
4 xRCOMP
(47)
A standard value of 8.2 nF is selected for CCOMP
STEP4: Determine CHF to cancel the ESR zero.
Knowing RCOMP, RESR and CCOMP, CHF is calculated as follows:
RESR u COUT u CCOMP
CHF
103 pF
RCOMP u CCOMP RESR u COUT
(48)
A standard value of 100 pF is selected for CHF
36
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
LM5121/LM5121-Q1
www.ti.com
SNVS963A – SEPTEMBER 2013 – REVISED SEPTEMBER 2013
Figure 41. Schematic
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM5121/LM5121-Q1
37
PACKAGE OPTION ADDENDUM
www.ti.com
24-Nov-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM5121MH/NOPB
ACTIVE
HTSSOP
PWP
20
73
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LM5121
MH
LM5121MHE/NOPB
ACTIVE
HTSSOP
PWP
20
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LM5121
MH
LM5121MHX/NOPB
ACTIVE
HTSSOP
PWP
20
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LM5121
MH
LM5121QMH/NOPB
ACTIVE
HTSSOP
PWP
20
73
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LM5121
QMH
LM5121QMHE/NOPB
ACTIVE
HTSSOP
PWP
20
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LM5121
QMH
LM5121QMHX/NOPB
ACTIVE
HTSSOP
PWP
20
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LM5121
QMH
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
24-Nov-2013
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LM5121, LM5121-Q1 :
• Catalog: LM5121
• Automotive: LM5121-Q1
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Nov-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
LM5121MHX/NOPB
HTSSOP
PWP
20
2500
330.0
16.4
LM5121QMHX/NOPB
HTSSOP
PWP
20
2500
330.0
16.4
Pack Materials-Page 1
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
6.95
7.1
1.6
8.0
16.0
Q1
6.95
7.1
1.6
8.0
16.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Nov-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM5121MHX/NOPB
HTSSOP
PWP
20
2500
367.0
367.0
35.0
LM5121QMHX/NOPB
HTSSOP
PWP
20
2500
367.0
367.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
PWP0020A
MXA20A (Rev C)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
Similar pages