DML1008LDS Description and Applications Features and Benefits The DML1008LDS is a single channel load switch with very low onresistance in a small package. It contains an N-channel MOSFET for up to VBIAS-1.5V input voltage operation and 6A current channel with 3.2V to 5.5V bias supply. The load switch is controlled by a low voltage control signal through ON pin. Portable Computers Ultrabooks Tablet PCs Set Top Boxed LCD TV Telecom/Networking/Datacom Equipment SSD Consumer Electronics Low RDS(ON) – Ensures On State Losses Are Minimized 0.8V to VBIAS-1.5V Input Voltage Range 6A Continuous Current Low RDS(ON) Internal NFETs 8mΩ at VBIAS = 5V, VIN = 1.05V, TA = +85°C 35µA Low Quiescent Current 10µs Turn On Rise Time 3.2V to 5.5V Bias Voltage Integrated Quick Output Discharge Resistor Moisture Sensitivity: Level 1 per J-STD-020 Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2) Halogen and Antimony Free. “Green” Device (Note 3) V-DFN3030-8 (Type R) Pin1 Top View Bottom View Ordering Information (Note 4) Part Number DML1008LDS-7 Notes: Case Packaging 3000/Tape & Reel V-DFN3030-8 (Type R) 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant. 2. See http://www.diodes.com/quality/lead_free.html for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green" and Lead-free. 3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and <1000ppm antimony compounds. 4. For packaging details, go to our website at http://www.diodes.com/products/packages.html. Pin Description Pin Number Pin Name 1, 2, EPAD IN 3 VBIAS 4 ON 5 6, 7, 8 GND OUT Pin Function Load Switch Input. Bypass capacitor is recommended to minimize input voltage dip. Recommended voltage range of this pin is 0.8V to VBIAS-1.5V to obtain optimal RON. Bias Voltage. Power supply input for the device. Recommended voltage range is 3.2V to 5.5V. Enable Input. Load switch is on when ON is pulled high. Load switch is off when ON is pulled low. Do not leave floating. Ground. Load switch output. Marking Information V-DFN3030-8 (Type R) YY WW NEW PRODUCT ADVANCE INFORMATION SINGLE CHANNEL SMART LOAD SWITCH LS08 DML1008LDS Document number: DS38448 Rev. 1 - 2 LS08 = Product Type Marking Code YYWW = Date Code Marking YY = Last Two Digits of Year (ex: 16 = 2016) WW = Week Code (01 to 53) 1 of 11 www.diodes.com August 2016 © Diodes Incorporated DML1008LDS Typical Application VIN IN OUT NEW PRODUCT ADVANCE INFORMATION CIN IN VOUT CL OUT DML1008LDS VBIAS VBIAS OUT ON GND CBIAS ON OFF Functional Block Diagram DML1008LDS Document number: DS38448 Rev. 1 - 2 2 of 11 www.diodes.com August 2016 © Diodes Incorporated DML1008LDS Absolute Maximum Ratings Maximum Operating Ratings NEW PRODUCT ADVANCE INFORMATION Parameter Rating Parameter Rating IN, ON, VBIAS, OUT to GND -0.3V to 6V Supply Voltage (VIN) VBIAS-1.5V Junction Temperature (TJ) +150°C Ambient Temperature (TA) -40°C to +85°C Storage Temperature (TS) -65°C to +150°C Package Thermal Resistance (θJC) 8°C/W ESD Rating HBM/CDM 2kV/1kV Package Thermal Resistance (θJA) 60°C/W Electrical Characteristics TA = +25°C, VBIAS=5V, VIN=1.05V, unless otherwise specified. Symbol VIN Parameter IN Supply Voltage Condition Min Typ Max Unit VON = 5V 0.8 1.05 VBIAS1.5 V — 3.2 5 5.5 V Maximum Continuous Current VON = 5V — 6 — A Maximum Pulsed Switch Current VIN = VON = 5V Pulse < 300μs, 2% Duty Cycle — 9 — A Quiescent Supply Current of VBIAS IOUT = 0V, VON = 5V — 35 — A VBIAS Shutdown Supply Current VON = 0V, VOUT = 0V — — 2 A IN Shutdown Supply Current VON = 0V, VOUT = 0V — — 2 A ON Leakage Current VON = 5V — — 1 A ON High Level Voltage — 1.2 — — V ON Low Level Voltage VONL Switching ON Resistance — — — 0.5 V VBIAS ID IPLS IQ IOFF IINOFF ION VONH VBIAS Supply Voltage IOUT = -200mA, VON = 5V, VBIAS = 5V — — 8 m RON Switch ON-State Resistance IOUT = -200mA, VON = 5V, VBIAS = 3.3V — — 10 m RPD Output Pull-Down Resistance IOUT = 15mA, VON = 0V — — 200 DML1008LDS Document number: DS38448 Rev. 1 - 2 3 of 11 www.diodes.com August 2016 © Diodes Incorporated DML1008LDS NEW PRODUCT ADVANCE INFORMATION Switching Characteristics Test conditions: TA = +25°C, CIN = 1μF, CL = 0.1μF, RL = 10Ω (unless otherwise specified). Symbol Parameter Min Typ Max Unit VIN = 1.5V, VBIAS = VON = 5V tON Turn-ON Time — 10 — tD-ON Turn-ON Delay time — 5 — tR Turn-ON Rise Time — 5 — tOFF Turn-OFF Time — 2 — tF Turn-OFF Fall Time — 3 — s VIN = 1.05V, VBIAS = VON = 5V tON Turn-ON Time — 10 — tD-ON Turn-ON Delay time — 5 — tR Turn-ON Rise Time — 5 — tOFF Turn-OFF Time — 2 — tF Turn-OFF Fall Time — 3 — DML1008LDS Document number: DS38448 Rev. 1 - 2 4 of 11 www.diodes.com s August 2016 © Diodes Incorporated DML1008LDS Typical Characteristics tON vs.VIN (VBIAS=5.5V) tON (s) tON (s) VIN (V) VIN (V) tD-ON vs.VIN (VBIAS=3.2V) tD-ON (s) tD-ON (s) tD-ON vs.VIN (VBIAS=5.5V) VIN (V) VIN (V) tR vs.VIN (VBIAS=3.2V) tR vs.VIN (VBIAS=5.5V) tR (s) tR (s) NEW PRODUCT ADVANCE INFORMATION tON vs.VIN (VBIAS=3.2V) VIN (V) DML1008LDS Document number: DS38448 Rev. 1 - 2 VIN (V) 5 of 11 www.diodes.com August 2016 © Diodes Incorporated DML1008LDS Typical Characteristics (Cont.) tOFF (s) tOFF (s) tOFF vs.VIN (VBIAS=5.5V) VIN (V) VIN (V) tF vs.VIN (VBIAS=3.2V) tF vs.VIN (VBIAS=5.5V) tF (s) tF (s) NEW PRODUCT ADVANCE INFORMATION tOFF vs.VIN (VBIAS=3.2V) VIN (V) VIN (V) DML1008LDS Document number: DS38448 Rev. 1 - 2 6 of 11 www.diodes.com August 2016 © Diodes Incorporated DML1008LDS Functional Characteristics Turn-ON & Turn-ON Rise Times VINX=1.05V, VBIAS=3.2V, CIN=1µF, CL=0.1µF, RL=10Ω NEW PRODUCT ADVANCE INFORMATION Turn-ON & Turn-ON Rise Times VINX=1.05V, VBIAS=5V, CIN=1µF, CL=0.1µF, RL=10Ω VON (5V/div) VON (5V/div) VOUT (200mV/div) VOUT (200mV/div) Turn-OFF & Turn-OFF FALL Times VINX=1.05V, VBIAS=3.2V, CIN=1µF, CL=0.1µF, RL=10Ω Turn-OFF & Turn-OFF FALL Times VINX=1.05V, VBIAS=5V, CIN=1µF, CL=0.1µF, RL=10Ω VON (5V/div) VON (5V/div) VOUT (200mV/div) VOUT (200mV/div) Turn-ON & Turn-OFF at IOUT= -10A VINX=1.05V, VBIAS=3.2V, CIN=1µF, CL=0.1µF, RL=0.1Ω Turn-ON & Turn-OFF at IOUT= -10A VINX=1.05V, VBIAS=5V, CIN=1µF, CL=0.1µF, RL=0.1Ω VON (5V/div) VBIAS (5V/div) DML1008LDS Document number: DS38448 Rev. 1 - 2 VON (5V/div) VBIAS (5V/div) VOUT (500mV/div) VOUT (500mV/div) IOUT (5A/div) IOUT (5A/div) 7 of 11 www.diodes.com August 2016 © Diodes Incorporated DML1008LDS Detailed Description VBIAS Voltage Range For optimal on-resistance of load switch, make sure V IN ≤ 1.5V + VBIAS and VBIAS is within the voltage range from 3.2V to 5.5V. On-resistance of load switch will be higher if VIN + 1.5V > VBIAS. Resistance curves of a typical sample device at different VBIAS = VIN at IOUT = -200mA are shown as below. IOUT vs.RDS(ON) RDS(ON) (m) IOUT vs.RDS(ON) RDS(ON) (m) NEW PRODUCT ADVANCE INFORMATION ON/OFF Control The DML1008LDS is enabled when the ON pin is on active high with 1.2V or above voltage. The device is disabled when the ON pin voltage is 0.5V or lower. The EN input is compatible with both TTL and CMOS logic. IOUT (A) IOUT (A) Applications Information The basic DML1008LDS application circuit is shown in the second page. Component selection is explained below. Input Capacitor A capacitor of 10μF or higher value is recommended to be placed close to the IN pins of DML1008LDS. This capacitor can reduce the voltage drop caused by the in-rush current during the turn-on transient of the load switch. A higher value capacitor can be used to further reduce the voltage drop during high-current application. Output Capacitor A capacitor of 0.1μF or higher value is recommended to be placed between the OUT pins and GND. The switching times are affected by the capacitance. A larger capacitor makes the initial turn-on transient smoother. This capacitor must be large enough to supply a fast transient load in order to prevent the output from dropping. Thermal Considerations To ensure proper operation, the maximum junction temperature of the DML1008LDS should not exceed +150°C. Several factors attribute to the junction temperate rise: load current, MOSFET on-resistance, junction-to-ambient thermal resistance, and ambient temperature. The maximum load current can be determined by: It is noted that the maximum continuous load current is 6A. Layout Guidelines Good PCB is important for improving the thermal performance of DML1008LDS. Place the input and output bypass capacitors close to the IN and OUT pins. The input and output PCB traces should be as wide as possible for the given PCB space. Use a ground plane to enhance the power dissipation capability of the device. DML1008LDS Document number: DS38448 Rev. 1 - 2 8 of 11 www.diodes.com August 2016 © Diodes Incorporated DML1008LDS Package Outline Dimensions (All dimensions in mm.) Please see http://www.diodes.com/package-outlines.html for the latest version. Package Type: V-DFN3030-8 (Type R) NEW PRODUCT ADVANCE INFORMATION (1) A3 A Seating Plane A1 D D2 b2 L1 E z1 E2 PIN1#ID L(8x) k V-DFN3030-8 (Type R) Dim Min Max Typ A 0.77 0.83 0.80 A1 0.00 0.05 0.03 A3 --0.203 b 0.25 0.35 0.30 b2 1.55 1.65 1.60 D 2.95 3.05 3.00 D2 2.30 2.50 2.40 E 2.95 3.05 3.00 E2 1.50 1.70 1.60 e 0.65 BSC k --0.30 L 0.35 0.45 0.40 L1 0.05 0.15 0.10 z --0.375 z1 --0.30 All Dimensions in mm b(8x) z e Suggested Pad Layout Please see http://www.diodes.com/package-outlines.html for the latest version. (1) Package Type: V-DFN3030-8 (Type R) X1 X C Y Dimensions G C1 C2 Y1 C C1 C2 G X X1 X2 Y Y1 Value (in mm) 0.65 1.30 2.60 0.30 0.30 1.60 2.40 0.40 1.60 X2 DML1008LDS Document number: DS38448 Rev. 1 - 2 9 of 11 www.diodes.com August 2016 © Diodes Incorporated DML1008LDS NEW PRODUCT ADVANCE INFORMATION Surface Mount Reel Specifications (All dimensions in mm.) DML1008LDS Document number: DS38448 Rev. 1 - 2 10 of 11 www.diodes.com August 2016 © Diodes Incorporated DML1008LDS IMPORTANT NOTICE NEW PRODUCT ADVANCE INFORMATION DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes Incorporated. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2016, Diodes Incorporated www.diodes.com DML1008LDS Document number: DS38448 Rev. 1 - 2 11 of 11 www.diodes.com August 2016 © Diodes Incorporated