Hirose H/MSA3057A18-10PCY-N Ms type lower profile plug(circular connector conforming to mil-c-5015) Datasheet

NEW
MS type Lower Profile Plug
H/MS Series
Circular connector conforming to MIL-C-5015
PAT.P
Connector Height Comparison
18-10 Size
50.1mm
45.5mm
41mm
70mm
54.5mm
3057-10
56.5mm
3057-10
18
Existing MS Connector
Lower-profile Plug
22-22 Size
48.2mm
2. Cable Exit in 360° Directions
Existing MS Connector
63.8mm
45.8mm
78.7mm
60.7mm
3057-12
When compared with existing H/MS Series connectors
the overall height of plug assemblies is lower, allowing it
to be used in space constrained applications.
3057-12
1. 20% Height Reduction
22
■Features
53.2mm
Lower-profile Plug
The cable can exit in any of the 8 fixed direction, in 45°
increments.
3. Simple Assembly
The 2-piece design consisting of the contact/insulator
assembly and the back-shell assembly allows termination
without the use of any specialized tools.
Cable Exit Direction of 360°
4. Water and Dust Protection
IP 67 rating when fully terminated and mated with
corresponding part.
5. TUV Certification
Provided with a protective circuit function for TUV
certification. The (D) pin is directly connected to the
outside metal case.
■Applications
Factory automation equipment, robotic equipment, servo
motors, and a wide variety of industrial and measuring
instruments.
Plug
°)
(45
Can be changed
in 45 degree increments
2004.6
1
■Product Specifications
Voltage rating
250VAC, 250V DC (pollution degree: 3, overvoltage category: 3)
Operating temperature range
500V AC, 500V DC (pollution degree: 2, overvoltage category: 2)
Rating
Current rating
-25ç to +125ç
Storage temperature range
23A Max. (18-10 size)
-25ç to +125ç
46A Max. (22-22 size)
Specification
Item
18-10 size
Conditions
22-22 size
1. Contact resistance
3 m ohms max.
1 m ohms max.
2. Insulation resistance 5000 M ohms min.
3. Withstanding voltage No flashover or insulation breakdown.
4. Vibration
No electrical discontinuity for 10 ms max.
5. Shock
1A DC
500 V DC
2250V AC/one minute.
Frequency: 10 to 500 Hz, single amplitude of 0.75 mm,
acceleration of 98 m/s2 for 3 hours in 3 axis.
Acceleration of 490 m/s2, 11ms duration, sine half-wave
waveform, 3 cycles in each of the 3 axis.
Contact resistance:
Contact resistance:
6. Durability
500 cycles
4.5 m ohms max.
1.5 m ohms max.
(insertion/ withdrawal)
Temperature: -55ç ➝ Room temperature to +125ç ➝ Room
temperature Time: 30 ➝ 10 to 15 ➝ 30 ➝ 10 to 15 (Minutes)
7. Temperature cycle
Insulation resistance: 5000 M ohms min.
5 cycles.
Insulation resistance: 50 M ohms min. (Humidity state)
96 hours at temperature of 71ç and humidity of 95% .
8. Humidity
500 M ohms min. (Dry state)
No dust penetration.
9. Water/dust
When mated with corresponding connector.
No water penetration when submerged for 0.5 hour at the depth of 1 meter.
protection
■Materials
Item
Material
Finish
Remarks
Body
Aluminum alloy
Black chromate
-------------------
Insulator
PPS
Color: Black
UL94V-0
Socket Contacts
Copper alloy
Silver plating
-------------------
Gasket
Silicone Rubber
Color: Black
-------------------
Bushing
Chloroprene rubber
Color: Black
-------------------
■Additional Product Information
1. Product number suffixes
(10) Supplied with a wire hole in the locking ring (to prevent loosening of the ring).
(11) Supplied without the wire hole in the locking ring.
2. Corresponding receptacles.
18-10 Size: Part number H/MS3102A18-10P-D-T1(10)
22-22 Size: Part number H/MS3102A22-22P-D-T(10)
2
■Plug
41
H/MS08A18-10S-DT10D(10)
Ø33.5
A
D
X
B
C
45.5
18-10S
3057-10
31
Shown one type.
Part Number
CL No.
H/MS08A18-10S-DT10D(10)
120-0476-3-10
H/MS08A18-10S-DT10D(11)
120-0476-3-11
H/MS08A18-10S-DT10D1(10)
120-0481-3-10
H/MS08A18-10S-DT10D1(11)
120-0481-3-10
Number of Contacts
Weight
4
89g
Applicable Cable Diameter Contact solder pot inner diameter
Ø12~Ø14.3mm
2.5mm
Ø10~Ø12.5mm
41
H/MS08A18-10S-DT10C(10)
Ø33.5
A
D
X
18-10S
C
35.5
B
Ø30
Shown one type.
Part Number
CL No.
H/MS08A18-10S-DT10C(10)
120-0480-0-10
H/MS08A18-10S-DT10C(11)
120-0480-0-11
Number of Contacts
Weight
4
77.6g
Applicable Cable Diameter Contact solder pot inner diameter
Ø13~Ø14.3mm
2.5mm
45.8
H/MS08A22-22S-DT12D(10)
D
22-22S
X
B
C
53.2
Ø39.5
A
3057-12
36
Shown one type.
Part Number
CL No.
H/MS08A22-22S-DT12D(10)
120-0477-6-10
H/MS08A22-22S-DT12D(11)
120-0477-6-11
H/MS08A22-22S-DT12D1(10)
120-0482-6-10
H/MS08A22-22S-DT12D1(11)
120-0482-6-11
Number of Contacts
Weight
Applicable Cable Diameter Contact solder pot inner diameter
Ø13~Ø15.9mm
4
127g
4.5mm
Ø10~Ø13.5mm
3
BAssembly Procedures
Process
Outline of assembly
B
B
A
Pre-solder
Conductor portion
A
Back-shell
B
Contacts
Bushing
Solder
1
Insulator/contact assembly
Washer
30
Table 1
Cable
57
Strain relief clamp
B
18-10 Size
24mm
13mm
22-22 Size
33mm
15mm
-10
A
a. Pass the strain relief clamp, washer, bushing, and hood over the cable, in this order.
b. Prepare the cable and conductors per the dimensions in Table 1.
c. Bend the exposed conductor to the B dimension as indicated in Table 1.
d. Pre-solder the exposed conductor and solder it as shown to the exposed contact.
Note: Use care not to damage the conductor’s insulation.
4.5 mm min.
Strain relief clamp
Screw
Back-shell
Cable
Set screw
(Hexagonal hole opposite side 1.27 mm)
3057-10
Locking ring
2
Table 2
Clamp
Locking Ring
Cable Clamp
3 to 3.5N • m
5 to 6N • m
Washer
Bushing
a. Place over the contact/insulator assembly (in the following order:Back shell, bushing, washer, strain relief clamp).
b. Tighten the Locking ring and Cable clamp to the torque values per Table 2.
c. Tighten the set screw to a torque value of 0.3-0.4 N-m
HRS recommended tool: PB205/1.27 (CL150-0066-3)or equivalent.
d. Using screwdriver tighten the two strain relief clamp screws until both sides of the moveable part are in contact with the cable clamp.
®
5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN
PHONE: 81-3-3491-9741, FAX: 81-3-3493-2933
http://www.hirose.com
4
The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpose of improvements.
Similar pages