TI COP472WM-3/63 Cop472-3 liquid crystal display controller Datasheet

COP472-3
COP472-3 Liquid Crystal Display Controller
Literature Number: SNOSBQ3
COP472-3 Liquid Crystal Display Controller
General Description
Features
The COP472–3 Liquid Crystal Display (LCD) Controller is a
peripheral member of the COPSTM family, fabricated using
CMOS technology. The COP472-3 drives a multiplexed liquid crystal display directly. Data is loaded serially and is held
in internal latches. The COP472-3 contains an on-chip oscillator and generates all the multi-level waveforms for backplanes and segment outputs on a triplex display. One
COP472-3 can drive 36 segments multiplexed as 3 x 12
(4(/2 digit display). Two COP472-3 devices can be used together to drive 72 segments (3 x 24) which could be an 8(/2
digit display.
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Direct interface to TRIPLEX LCD
Low power dissipation (100 mW typ.)
Low cost
Compatible with all COPS processors
Needs no refresh from processor
On-chip oscillator and latches
Expandable to longer displays
Operates from display voltage
MICROWIRETM compatible serial I/O
20-pin Dual-In-Line package and 20-pin SO
Block Diagram
TL/DD/6932 – 1
COPSTM and MICROWIRETM are trademarks of National Semiconductor Corporation.
C1996 National Semiconductor Corporation
TL/DD/6932
RRD-B30M56/Printed in U. S. A.
http://www.national.com
COP472-3 Liquid Crystal Display Controller
July 1995
Absolute Maximum Ratings
Voltage at CS, DI, SK pins
Voltage at all other Pins
b 0.3V to a 9.5V
Storage Temperature
b 0.3V to VDD a 0.3V
Operating Temperature Range
b 65§ C to a 150§ C
Lead Temp. (Soldering, 10 Seconds)
300§ C
0§ C to 70§ C
DC Electrical Characteristics
GND e 0V, VDD e 3.0V to 5.5V, TA e 0§ C to 70§ C (depends on display characteristics)
Parameter
Conditions
Min
Max
Units
3.0
5.5
Volts
VDD e 5.5V
250
mA
VDD e 3V
100
mA
0.7 VDD
0.8
9.5
Volts
Volts
VDDb0.6
0.6
VDD
Volts
Volts
VDDb0.4
0.4
VDD
Volts
Volts
During
BP a Time
VDDb DV
(/3 VDDb DV
VDD
(/3 VDD a DV
Volts
Volts
During
BPb Time
0
)/3 VDDb DV
DV
)/3 VDD a DV
Volts
Volts
During
BP a Time
0
)/3 VDDb DV
DV
)/3 VDD a DV
Volts
Volts
During
BPb Time
VDDb DV
(/3 VDDb DV
VDD
(/3 VDD a DV
Volts
Volts
Power Supply Voltage, VDD
Power Supply Current, IDD (Note 1)
Input Levels
DI, SK, CS
VIL
VIH
BPA (as Osc. in)
VIL
VIH
Output Levels, BPC (as Osc. Out)
VOL
VOH
Backplane Outputs (BPA, BPB, BPC)
VBPA, BPB, BPC ON
VBPA, BPB, BPC OFF
VBPA, BPB, BPC ON
VBPA, BPB, BPC OFF
Segment Outputs (SA1 E SA4)
VSEG ON
VSEG OFF
VSEG ON
VSEG OFF
Internal Oscillator Frequency
15
80
kHz
Frame Time (Int. Osc. d 192)
2.4
12.8
ms
Scan Frequency (1/TSCAN)
39
208
Hz
4
250
kHz
SK Clock Frequency
SK Width
1.7
ms
1.0
100
ms
ns
1.0
1.0
ms
ms
DI
Data Setup, tSETUP
Data Hold, tHOLD
CS
tSETUP
tHOLD
Output Loading Capacitance
100
Note 1: Power supply current is measured in stand-alone mode with all outputs open and all inputs at VDD.
Note 2: DV e 0.05VDD.
http://www.national.com
2
pF
Absolute Maximum Ratings
Storage Temperature
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales
Office/Distributors for availability and specifications.
Voltage at CS, DI, SK Pins
Voltage at All Other Pins
Operating Temperature Range
b 65§ C to a 150§ C
Lead Temperature
(Soldering, 10 seconds)
b 0.3V to a 9.5V
300§ C
b 0.3V to VDD a 0.3V
b 40§ C to a 85§ C
DC Electrical Characteristics
GND e 0V, VDD e 3.0V to 5.5V, TA e b40§ C to a 85§ C (depends on display characteristics)
Parameter
Conditions
Power Supply Voltage, VDD
Power Supply Current, IDD (Note 1)
3.0
5.5
Volts
mA
VDD e 3V
120
mA
0.7 VDD
0.8
9.5
Volts
Volts
VDDb0.6
0.6
VDD
Volts
Volts
VDDb0.4
0.4
VDD
Volts
Volts
During
BP a Time
VDDb DV
(/3 VDDb DV
VDD
(/3 VDD a DV
Volts
Volts
During
BPb Time
0
)/3 VDDb DV
DV
)/3 VDD a DV
Volts
Volts
During
BP a Time
0
)/3 VDDb DV
DV
)/3 VDD a DV
Volts
Volts
During
BPb Time
VDDb DV
(/3 VDDb DV
VDD
(/3 VDD a DV
Volts
Volts
Output Levels, BPC (as Osc. Out)
VOL
VOH
Segment Outputs (SA1 E SA4)
VSEG ON
VSEG OFF
VSEG ON
VSEG OFF
Units
300
BPA (as Osc. In)
VIL
VIH
VBPA, BPB, BPC ON
VBPA, BPB, BPC OFF
Max
VDD e 5.5V
Input Levels
DI, SK, CS
VIL
VIH
Backplane Outputs (BPA, BPB, BPC)
VBPA, BPB, BPC ON
VBPA, BPB, BPC OFF
Min
Internal Oscillator Frequency
15
80
kHz
Frame Time (Int. Osc. d 192)
2.4
12.8
ms
Scan Frequency (1/TSCAN)
39
208
Hz
4
250
kHz
SK Clock Frequency
SK Width
1.7
ms
1.0
100
ms
ns
1.0
1.0
ms
ms
DI
Data Setup, tSETUP
Data Hold, tHOLD
CS
tSETUP
tHOLD
Output Loading Capacitance
100
pF
Note 1: Power supply current is measured in stand-alone mode with all outputs open and all inputs at VDD.
Note 2: DV e 0.05 VDD.
3
http://www.national.com
Dual-In-Line Package
Top View
Pin
CS
VDD
GND
DI
SK
BPA
BPB
BPC
SA1 E SC4
Description
Chip select
Power supply (display voltage)
Ground
Serial data input
Serial clock input
Display backplane A (or oscillator in)
Display backplane B
Display backplane C (or oscillator out)
12 multiplexed outputs
TL/DD/6932–2
Order Number COP472MW-3 or COP472N-3
See NS Package Number M20A or N20A
FIGURE 2. Connection Diagram
TL/DD/6932 – 3
FIGURE 3. Serial Load Timing Diagram
TL/DD/6932 – 4
FIGURE 4. Backplane and Segment Waveforms
TL/DD/6932 – 5
FIGURE 5. Typical Display Internal Connections
Epson LD-370
http://www.national.com
4
Functional Description
The COP472-3 drives 36 bits of display information organized as twelve segments and three backplanes. The
COP472-3 requires 40 information bits: 36 data and 4 control. The function of each control bit is described below.
Display information format is a function of the LCD interconnections. A typical segment/backplane configuration is illustrated in Figure 5 , with this configuration the COP472-3 will
drive 4 digits of 9 segments.
To adapt the COP472-3 to any LCD display configuration,
the segment/backplane multiplex scheme is illustrated in
Table I.
Two or more COP472-3 chips can be cascaded to drive
additional segments. There is no limit to the number of
COP472-3’s that can be used as long as the output loading
capacitance does not exceed specification.
SEGMENT DATA BITS
Data is loaded in serially, in sets of eight bits. Each set of
segment data is in the following format:
SA
Segment,
Backplane
1
2
3
4
5
6
7
8
SA1, BPC
SB1, BPB
SC1, BPA
SC1, BPB
SB1, BPC
SA1, BPB
SA1, BPA
SB1, BPA
SH
SG
SF
SE
SD
SC
SB
SA
9
10
11
12
13
14
15
16
SA2, BPC
SB2, BPB
SC2, BPA
SC2, BPB
SB2, BPC
SA2, BPB
SA2, BPA
SB2, BPA
SH
SG
SF
SE
SD
SC
SB
SA
Digit 2
17
18
19
20
21
22
23
24
SA3, BPC
SB3, BPB
SC3, BPA
SC3, BPB
SB3, BPC
SA3, BPB
SA3, BPA
SB3, BPA
SH
SG
SF
SE
SD
SC
SB
SA
Digit 3
25
26
27
28
29
30
31
32
SA4, BPC
SB4, BPB
SC4, BPA
SC4, BPB
SB4, BPC
SA4, BPB
SA4, BPA
SB4, BPA
SH
SG
SF
SE
SD
SC
SB
SA
Digit 4
33
34
35
36
37
38
39
40
SC1, BPC
SC2, BPC
SC3, BPC
SC4, BPC
not used
Q6
Q7
SYNC
SPA
SP2
SP3
SP4
Digit 1
Digit 2
Digit 3
Digit 4
SC
SD
SE
SF
SG
SH
CONTROL BITS
The fifth set of 8 data bits contains special segment data
and control data in the following format:
SYNC
TABLE I. COP472-3 Segment/Backplane
Multiplex Scheme
Bit Number
SB
Data is shifted into an eight bit shift register. The first bit of
the data is for segment H, digit 1. The eighth bit is segment
A, digit 1. A set of eight bits is shifted in and then loaded into
the digit one latches. The second set of 8 bits is loaded into
digit two latches. The third set into digit three latches, and
the fourth set is loaded into digit four latches.
Q7
Q6
X
SP4
SP3
SP2
SP1
The first four bits shifted in contain the special character
segment data. The fifth bit is not used. The sixth and seventh bits program the COP472-3 as a stand alone LCD driver or as a master or slave for cascading COP472-3’s. BPC
of the master is connected to BPA of each slave. The following table summarizes the function of bits six and seven:
Data to
Numeric Display
Digit 1
Q7
Q6
1
1
Slave
Function
0
1
Stand Alone
1
0
Not Used
0
0
Master
BPC Output
BPA Output
Backplane
Output
Backplane
Output
Internal
Osc. Output
Internal
Osc. Output
Oscillator
Input
Backplane
Output
Oscillator
Input
Backplane
Output
The eighth bit is used to synchronize two COP472-3’s to
drive an 8(/2-digit display.
5
http://www.national.com
LOADING SEQUENCE TO DRIVE A 4(/2-DIGIT DISPLAY
Steps:
1. Turn CE low.
2. Clock in 8 bits of data for digit 1.
3.
4.
5.
6.
Clock in 8 bits of data for digit 2.
Clock in 8 bits of data for digit 3.
Clock in 8 bits of data for digit 4.
Clock in 8 bits of data for special segment and control
function of BPC and BPA.
0
0
1
1
SP4
SP3
SP2
SP1
7. Turn CS high.
Note: CS may be turned high after any step. For example to
load only 2 digits of data, do steps 1, 2, 3, and 7.
CS must make a high to low transition before loading data in
order to reset internal counters.
LOADING SEQUENCE TO DRIVE AN
8(/2-DIGIT DISPLAY
Two or more COP472-3’s may be connected together to
drive additional segments. An eight digit multiplexed display
is shown in Figure 7 . The following is the loading sequence
to drive an eight digit display using two COP472-3’s. The
right chip is the master and the left the slave.
Steps:
1. Turn CS low on both COP472-3’s.
TL/DD/6932 – 6
FIGURE 6. System Diagram – 4(/2 Digit Display
2. Shift in 32 bits of data for the slave’s four digits.
3. Shift in 4 bits of special segment data: a zero and three
ones.
1
1
1
0
SP4
SP3
SP2
SP1
This synchronizes both the chips and BPA is oscillator
input. Both chips are now stopped.
Turn CS high to both chips.
Turn CS low to master COP472-3.
Shift in 32 bits of data for the master’s 4 digits.
Shift in four bits of special segment data, a one and
three zeros.
4.
5.
6.
7.
0
0
0
1
SP4
SP3
SP2
SP1
This sets the master COP472-3 to BPA as a normal
backplane output and BPC as oscillator output. Now
both the chips start and run off the same oscillator.
8. Turn CS high.
The chips are now synchronized and driving 8 digits of display. To load new data simply load each chip separately in
the normal manner, keeping the correct status bits to each
COP472-3 (0110 or 0001).
http://www.national.com
TL/DD/6932 – 7
FIGURE 7. System Diagram – 8(/2 Digit Display
6
Physical Dimensions inches (millimeters) unless otherwise noted
20-Lead Molded DIP (M)
Order Number COP472MW-3
NS Package Number M20B
7
http://www.national.com
COP472-3 Liquid Crystal Display Controller
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
20-Lead Molded DIP (N)
Order Number COP472N-3
NS Package Number N20A
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and whose
failure to perform, when properly used in accordance
with instructions for use provided in the labeling, can
be reasonably expected to result in a significant injury
to the user.
National Semiconductor
Corporation
1111 West Bardin Road
Arlington, TX 76017
Tel: 1(800) 272-9959
Fax: 1(800) 737-7018
http://www.national.com
2. A critical component is any component of a life
support device or system whose failure to perform can
be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or
effectiveness.
National Semiconductor
Europe
Fax: a49 (0) 180-530 85 86
Email: europe.support @ nsc.com
Deutsch Tel: a49 (0) 180-530 85 85
English Tel: a49 (0) 180-532 78 32
Fran3ais Tel: a49 (0) 180-532 93 58
Italiano Tel: a49 (0) 180-534 16 80
National Semiconductor
Hong Kong Ltd.
13th Floor, Straight Block,
Ocean Centre, 5 Canton Rd.
Tsimshatsui, Kowloon
Hong Kong
Tel: (852) 2737-1600
Fax: (852) 2736-9960
National Semiconductor
Japan Ltd.
Tel: 81-043-299-2308
Fax: 81-043-299-2408
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and Automotive www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
www.ti.com/video
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
Similar pages