TI BQ2056VSNTR Low-dropout li-ion charge-control ics with autocompâ ¢ charge-rate compensation Datasheet

bq2056/T/V
Low-Dropout Li-Ion Charge-Control ICs with
AutoComp™ Charge-Rate Compensation
Features
General Description
➤ Significant reduction in charge
time with AutoComp charge-rate
compensation
The bq2056 series ICs are low-cost
precision linear charge-control devices for Li-Ion batteries. With a
minimum number of external components, the bq2056 is a complete lowdropout linear charger. The dropout
voltage is typically less than 0.5V
when the bq2056 is used with an external PNP transistor or P-channel
FET. Features include proprietary
➤ Ideal for low-dropout linear regulator design
➤ 1-cell, 2-cell, and programmable
multicell versions
➤ Low-cost charger implementation
with minimum number of external components
➤ Programmable current limit to
accommodate any battery size
automatic charge-rate compensation
(AutoComp) and a trickle-charger interface output for reviving deeply
discharged cells. The bq2056 supports a single-cell 4.1V pack and the
2056T supports a two-cell 8.2V pack.
The bq2056V may be externally programmed for supporting other voltages. All versions feature a sleep
mode for low-power applications.
Functional Block Diagram
➤ Interface to external trickle
charger for reviving deeply discharged batteries
+
SNS
TRKL
2.0V
➤ High-accuracy charge control
BAT
➤ Sleep mode for low power consumption
COMP
➤ Direct battery voltage sense
wi t h o ut r e s i s ti v e d i v i d e r s
(bq2056 and bq2056T)
SNS
KCOMP
+
VREG
100mV
CC
+
VSS
➤ Small 8-pin SOIC package
INH
BDbq2056.eps
Pin Names
Pin Connections
Charge-inhibit input
SNS
Current sense input
TRKL
Trickle-charge
interface output
BAT
Battery voltage input
CC
VSS
Ground
Charge control
output
COMP
Charge-rate
compensation input
VCC
Supply input
INH
INH
1
8
VCC
TRKL
2
7
CC
VSS
3
6
BAT
COMP
4
5
SNS
8-Pin DIP or Narrow SOIC
PN-205601.eps
10/98 B
1
bq2056/T/V
SNS
Pin Descriptions:
INH
Battery current is sensed via the voltage
developed on this pin by an external senseresistor, connected in series with the negative terminal of the battery pack.
Charge-inhibit input
When input to this pin is high, the bq2056
suspends the charge in progress and places
the device in sleep mode. When input is low,
the bq2056 resumes operation.
TRKL
BAT
This output is driven low if the battery voltage is less than an internal threshold level
and INH is low. This open-drain output can
enable an external trickle charger to revive a
deeply discharged battery.
Ground
COMP
Charge-rate compensation input
Battery voltage input
This is the battery voltage sense input. It is
tied directly to the positive side of the battery pack on bq2056 and bq2056T versions.
A simple resistive divider is required to
generate this input for bq2056V.
Trickle-charge interface output
VSS
Current sense input
CC
Charge-control output
CC is an open-collector output that is used
to control the charging current to the battery.
VCC
This input is used to set the charge-rate
compensation level. The voltage regulation
output may be programmed to vary as a
function of the charge current delivered to
the battery. This feature, called AutoComp,
provides compensation for internal cell impedance and voltage drops in protection
circuitry and therefore may be used to
safely reduce charging time. Connecting
this pin to VSS disables the AutoComp feature.
2
VCC supply input
bq2056/T/V
R3
Q1
4.7K
2N3906
5 VDC
DC+
2TX788B
Q2
D1
1N5817
R5
2.7K
R5
2K
C2
DC-
0.1 F
1
2
3
4
INH
VCC
TRKL
CC
VS
BAT
COMP
SNS
8
7
BAT+
6
C1
10 F
10V
5
BAT-
bq2056
R2 1K
R6
0.3
R1
1K
bq2056sc.eps
Figure 1. Low-Dropout Single-Cell Li-Ion Charger
is accomplished by comparing pin BAT voltage to the internal threshold VMIN. While pin BAT voltage is less
than VMIN and pin INH is low, the open-drain output
TRKL is driven low and the voltage/current regulator is
disabled (CC=high-Z). In the bq2056V, low-voltage detection occurs when the voltage on pin BAT is less than
or equal to VMIND. As shown in Figure 1, TRKL enables
an external trickle-charge circuit to bring the battery
voltage up to VMIN or VMIND.
Functional Description
The bq2056 supports a precision current- and voltagelimited charging system for Li-Ion batteries. The no-load
voltage regulation references (VREG) for the bq2056 and
bq2056T are maintained at 4.1V and 8.2V, respectively.
The bq2056V provides variable regulation to accommodate a wide range of charge voltages and may be used to
meet tighter tolerance requirements through external
trimming. The functional block diagram for the bq2056
is on the first page of this data sheet, and Figure 1 illustrates a typical application.
Current Regulation
The bq2056 provides current regulation while the pack
voltage is below the voltage limit. Charge-current feedback, applied through pin SNS, maintains regulation
around a threshold of VSNS. The following formula calculates the value of the sense-resistor connected in series
with the negative terminal of the battery pack (Figure 3):
Charge Algorithm
The bq2056 completes the charge cycle in two phases. A
constant current phase replenishes approximately 70%
of battery capacity, while an accurate voltage regulation
phase completes the charge.
RSNS= 0.1/ IMAX
Figure 2 shows a typical charge algorithm for bq2056,
including charge qualification, current regulation, and
voltage regulation phases.
where IMAX is the maximum charging current. IMAX
should not exceed 1A.
Charge Qualification
An external PNP or power P-FET may be used as the series pass element with control provided through output
pin CC.
During charge qualification the bq2056 detects a low
battery and reports this status on pin TRKL. Detection
3
bq2056/T/V
External
Trickle Charge
Enabled
AutoComp™
Phase
VREG
Current
Voltage Regulation
VMIN
Voltage
Voltage
IMAX
Current
Regulation
Cu
rre
nt
2056chg.eps
Figure 2. bq2056 Charge Algorithm
voltage to compensate for the battery’s internal impedance and undesired voltage drops in the circuit.
Voltage Regulation
Voltage regulation feedback is through pin BAT. This pin
is connected directly to the pack in the bq2056 and
bq2056T. This voltage is compared with the voltage
regulation reference, VREG. In the bq2056V, a resistive
divider may be used to generate this input (Figure 4). In
this case, the voltage presented on pin BAT is compared
with the internal reference voltage VREF. The resistor
values RB1 and RB2 (Figure 4) are calculated based on
the following equation:
For bq2056 and bq2056T, the voltage across the battery
pack, VPAK, is
VPAK = VREG + (KCOMP ∗ voltage on pin COMP)
For bq2056V, the compensation voltage is added to the
product of the internal voltage reference, VREF, and the
gain, KDIV, of the external resistive divider between the
battery pack and BAT input, (Figure 4).
RB1 N ∗ VCELL
=
−1
RB2
VREF
VPAK = (VREF ∗ KDIV) + (KCOMP ∗ voltage on pin COMP)
Sleep Mode
where
N
= Number of cells in series
The charge function may be disabled through pin INH.
When INH is driven high, internal current consumption
is reduced, and pins CC and TRKL assumes a highimpedance output state.
VCELL = Manufacturer-specified charging voltage
Automatic Charge-Rate Compensation
(AutoComp) Feature
To reduce charging time, the bq2056 series uses the proprietary AutoComp technique to compensate safely for
internal impedance of battery and any voltage drops in
the protection circuitry. This maximizes battery’s capacity while reducing charging time. Compensation is
through input pin COMP (Figure 5). A portion of the
current-sense voltage, presented through this pin, is
scaled by a factor of KCOMP and summed with the regulation reference, VREG. This process increases the output
4
bq2056/T/V
BAT+
RB1
3
BAT
VSS
SNS
5
BAT-
bq2056
bq2056T
bq2056V
3
RB2
VSS
SNS
RSNS
6
BAT-
5
bq2056V
RSNS
2056CSR.eps
2056BVD.eps
Figure 4. Battery Voltage Divider for
bq2056V
Figure 3. Current-Sensing Resistor
3
VCC
4 COMP SNS 5
BAT-
bq2056
bq2056T
bq2056V
RC2
RC1
RSNS
2056ACC.eps
Figure 5. AutoComp Circuit
5
bq2056/T/V
Absolute Maximum Ratings
Symbol
Parameter
Min
Max
Units
VCC
VCC relative to VSS
-0.3
+18
V
VT
DC voltage applied on any pin
(excluding VCC) relative to VSS
-0.3
VCC+0.3
V
TOPR
Operating ambient temperature
-20
70
°C
TSTG
Storage temperature
-40
125
°C
TSOLDER
Soldering temperature
-
260
°C
PD
Power dissipation
300
mW
Notes
10s max.
DC Thresholds (TA=TOPR and VCC = 5–17V unless otherwise specified)
Symbol
Parameter
Rating
Unit
Tolerance
VREG
(bq2056)
Voltage regulation reference
4.10
V
±1%
VREG
(bq2056T)
Voltage regulation reference
8.20
V
±1%
VREF
(bq2056V)
Voltage regulation reference
3.35
V
±1%
VSNS
Current regulation reference
100
mV
±15%
VMIN
(bq2056)
Trickle-charge voltage
reference
2.0
V
±15%
VMIN
(bq2056T)
Trickle-charge voltage
reference
4.0
V
±15%
VMIND
(bq2056V)
Trickle-charge voltage
reference
1.64
V
±15%
KCOMP
(bq2056)
AutoComp constant
2.0
-
±10%
KCOMP
(bq2056T)
AutoComp constant
4.0
-
±10%
KCOMP
(bq2056V)
AutoComp constant
1.7
-
±10%
6
Notes
bq2056/T/V
Recommended DC Operating Conditions (TA=25°C)
Symbol
Parameter
Min
Typical
Max
Units
Notes
VCC
Supply voltage relative to VSS
5.0
-
17.0
V
ICC
Supply current
-
1
2
mA
INH = LOW
ICCS
Sleep current
-
10
30
µA
INH = HIGH
VIL
Input low
-
-
0.5
V
Pin INH
VIH
Input high
2.0
-
-
V
Pin INH
VOL
Output low
-
-
0.4
V
Pin TRKL, IOL = 1mA
IOH
Leakage current
-
-
1
µA
Pin TRKL
ISNK
Sink current
-
-
40
mA
Pin CC
Min
Typical
Max
Units
Impedance
Symbol
Parameter
RBAT
BAT pin input impedance
-
1
-
MΩ
RSNS
SNS pin input impedance
-
100
-
kΩ
RCOMP
COMP pin input impedance
-
100
-
kΩ
7
Notes
bq2056/T/V
8-Pin DIP (PN)
8-Pin PN (0.300" DIP)
Inches
D
E1
E
A
B1
A1
L
C
B
S
e
G
8
Millimeters
Dimension
A
Min.
Max.
Min.
Max.
0.160
0.180
4.06
4.57
A1
0.015
0.040
0.38
1.02
B
0.015
0.022
0.38
0.56
B1
0.055
0.065
1.40
1.65
C
0.008
0.013
0.20
0.33
D
0.350
0.380
8.89
9.65
E
0.300
0.325
7.62
8.26
E1
0.230
0.280
5.84
7.11
e
0.300
0.370
7.62
9.40
G
0.090
0.110
2.29
2.79
L
0.115
0.150
2.92
3.81
S
0.020
0.040
0.51
1.02
bq2056/T/V
8-Pin SOIC Narrow (SN)
8-Pin SN (0.150" SOIC)
Inches
9
Millimeters
Dimension
A
Min.
Max.
Min.
Max.
0.060
0.070
1.52
1.78
A1
0.004
0.010
0.10
0.25
B
0.013
0.020
0.33
0.51
C
0.007
0.010
0.18
0.25
D
0.185
0.200
4.70
5.08
E
0.150
0.160
3.81
4.06
e
0.045
0.055
1.14
1.40
H
0.225
0.245
5.72
6.22
L
0.015
0.035
0.38
0.89
bq2056/T/V
Data Sheet Revision History
Change No.
1
1
Note:
Page No.
6
6
Description
Changed tolerance for VREG and VREF in
DC Thresholds table
Changed value and tolerance for KCOMP
in DC Thresholds table
Change 1 = Oct. 1998 B changes from March 1998.
10
Nature of Change
Was: ±0.7% with ±0.5% variation over power
supply and temperature range
Is: ±1% over power supply and temperature
range
Was: 2.0, ±15%
Is: bq2056: 2.0, ±10%
bq2056T: 4.0, ±10%
bq2056V: 1.7, ±10%
bq2056/T/V
Ordering Information
bq2056
Package Option:
PN = 8-pin plastic DIP
SN = 8-pin narrow SOIC
Device:
bq2056 Li-Ion Fast-Charge IC for one cell
bq2056T Li-Ion Fast-Charge IC for two cells
bq2056V Programmable Li-Ion Fast-Charge IC
11
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  1999, Texas Instruments Incorporated
Similar pages