Panasonic FP0-RTD6 4-axis pulse output in a compact body Datasheet

■ FP-X Control Unit Dimensions (Unit: mm)
Dimensions when expansion cassettes
(function and communication) are installed
●AFPX-C14 ∗ ∗ (The same dimensions apply to the expansion I/O unit AFPX-E16∗)
COM
Status display LED
N
X0
X2
X5
X4
X7
X6
PROG. ERR.
3
7
3
0
X 4
0
Y
4
Programmable Controller
45
L
RUN
Input/output display LED
Application cassette
Communication cassette
X3
X1
FP-X
60
5
90
Panasonic
RUN
PROG.
Mode selection switch
RUN/PROG.
FP-X C14
min.
max.
V0
V1
45
Analog volume
Tool port connector
0V
Y2
Y1
Y0
24V
C0
C1
C2
Y3
C3
Y5
Y4
13.6
3.5
Application cassette
Communication cassette
Battery
Expansion unit connector
79
8.6
79
●AFPX-C30 ∗ ∗ (The same dimensions apply to the expansion I/O unit AFPX-E30∗ ∗)
100
Mounting dimension diagram
Status display LED
N COM
L
COM
RUN
Input/output display LED
X1
X0
X3
X2
X5
X4
X7
X9
X8
X6
XB
XA
XD
XC
Introducing a New Transistor Output Model
Pulse Output
XF
XE
2-M
4o
r2
PROG. ERR.
0
8
0
Y
8
7
F
7
X
D
-
5
90
FP-X C30
RUN
PROG.
min.
82 ±0.5
Panasonic
Mode selection switch
RUN/PROG.
max.
4-Axis Integrated Control
V0
Analog volume
V1
0V
USB connector
24V
Tool port connector
Y0
C0
Y2
Y1
C1
C2
Y4
Y3
Y7
C3
Y5
Y6
Y9
Y8
YA
C4
YC
YB
YD
Cassette attachment area 1 Cassette attachment area 2
Application cassette
Communication cassette
Battery
FP-X C14
Function cassette
Battery
Expansion unit connector
●AFPX-C60 ∗ ∗
52 ±0.5
92 ±0.5
FP-X C30
ARCT1B273E
DIN hook
Cassette attachment area 1
182 ±0.5
FP-X C60
190
N COM
L
COM
RUN
X
Y
Mode selection switch
RUN/PROG.
X0
PROG.
X3
X2
X5
X4
7 8
17 18
7 8
17 18
XC
COM
NC
XF
XE
COM
COM
COM
X11
X13
X12
X10
X15
X14
X17
X16
X19
X18
X1B
X1A
X1D
X1C
X1F
X1E
F
1F
D
1D
FP-X C60
V1
V2
max.
V3
0V
Tool port connector
XA
XD
max.
V0
min.
USB connector
X8
XB
Panasonic
min.
24V
X6
X9
ERR.
0
10
0
10
RUN
PROG.
Analog volume
X7
Y0
C0
Y2
Y1
C1
C2
Y4
Y3
Y7
C3
Y5
Y6
Y9
Y8
YA
C4
YC
YB
Y10
YD
Cassette attachment area 1
Application cassette
Communication cassette
Battery
C0
Y11
C1
C2
Y12
Y13
C3
C5
Y14
C4
Y15
Y17
Y16
Y19
Y18
Y1A
C6
Y1C
Y1B
Cassette attachment area 2
Application cassette
Battery
Y1D
Expansion connector part
Battery
Expansion unit connector
■ FP-X Expansion FP0 Adapter Dimensions (Unit: mm)
( 0.5 )
25
60
POWER
I/F
L
ERROR
45
Status
display LED
(7)
Panasonic
Expansion connector
90
AFPX-EFP0
FP0-A80
When the expansion
connector is
attached
45
Input/output display LED
X1
90
Status display LED
2-Axis Linear
Interpolation
Simultaneously
in 2 Pairs!
Appearance when mounted
with a C14 control unit
3.5
DIN hook
Power connector 24 V DC
Expansion hook
These materials are printed on ECF pulp.
These materials are printed with earth-friendly vegetable-based (soybean oil) ink.
Please contact ..........
Matsushita Electric Works, Ltd.
Automation Controls Business Unit
Head Office: 1048, Kadoma, Kadoma-shi, Osaka 571-8686, Japan
Telephone: +81-6-6908-1050
Facsimile: +81-6-6908-5781
http://www.nais-e.com/
14-point type
FP-X Programmable Controller
ARCT1B273E ’06.8
All Rights Reserved © 2006 COPYRIGHT Matsushita Electric Works, Ltd.
ARCT1B273E 200608-6YT
Specifications are subject to change without notice.
30-point type
60-point type
New
Printed in Japan.
Panasonic... the new name for
Matsushita Electric Works, Ltd.
Introducing
a Transistor
Output Type
4-axis pulse output in a compact body
Simultaneous 2-axis linear interpolation is
possible in two pairs
(C14 comes with 3 axes)
Servomotor and stepping motor control in production equipment has become increasingly
diversified while requiring a greater number of axes – for example, electronic control for
replacing cams, XY table + Z-axis control for cell-production and LCD alignment, 3D bending
process of corrugated paper boxes and heat exchanger pipes, high-density coil winding
operations etc. With such applications in mind, FP-X is a compact general-purpose PLC
suited for small-scale equipment controls with its 4-axis pulse output built into the compact
body, enabling multi-axis control in a very small space at a fraction of the equipment cost.
AFPX-C60
(Add-on cassette attached)
Ultra High-speed Processing
High-speed scan of 0.32 µs for a basic instruction
(1.9 ms scan time for 5 ksteps*1)
The processing speed of 0.32 µsec, sufficient for a compact PLC, is
even applicable when high-speed scanning is required.
*1: A 5-kstep program consisting of 35% basic instructions and 65% applied instructions
(data transfer, four operations)
Large Capacity with an Extra Margin
Program capacity of 32 ksteps with a sufficient
comment area*2
The program capacity of 32 ksteps, exceeding the capacity of most
compact PLCs, can flexibly handle a wide variety of applications
requiring future equipment expansion.
*2: C14: 16 ksteps
Great Expandability with a Wide
Variety of Options
Max. I/O expansion of 300 points and further expansion
with a function expansion cassette
The add-on cassette easily enables functional enhancements when
slightly more features are to be added, while keeping costs down.
The expansion FP0 adapter enables the connection of 3 additional
FP0 expansion units.
High Security
Program protection with an 8-digit password and a function
prohibiting uploads
USB-port Equipped*3
AFPX-C30
(Add-on cassette attached)
New Functions
Easy-to-use Temperature Control
Command (F356 EZPID)
MEWTOCOL Master Function
AFPX-C14
Ethernet Add-on Unit (Available Soon)
(Add-on cassette attached)
Trace Function
Easy direct connection with a PC via a commercial USB
cable (AB type)
*3: Not provided with C14.
2
3
Introducing
a Transistor
Output Type
4-axis pulse output in a compact body
Simultaneous 2-axis linear interpolation is
possible in two pairs
(C14 comes with 3 axes)
Servomotor and stepping motor control in production equipment has become increasingly
diversified while requiring a greater number of axes – for example, electronic control for
replacing cams, XY table + Z-axis control for cell-production and LCD alignment, 3D bending
process of corrugated paper boxes and heat exchanger pipes, high-density coil winding
operations etc. With such applications in mind, FP-X is a compact general-purpose PLC
suited for small-scale equipment controls with its 4-axis pulse output built into the compact
body, enabling multi-axis control in a very small space at a fraction of the equipment cost.
AFPX-C60
(Add-on cassette attached)
Ultra High-speed Processing
High-speed scan of 0.32 µs for a basic instruction
(1.9 ms scan time for 5 ksteps*1)
The processing speed of 0.32 µsec, sufficient for a compact PLC, is
even applicable when high-speed scanning is required.
*1: A 5-kstep program consisting of 35% basic instructions and 65% applied instructions
(data transfer, four operations)
Large Capacity with an Extra Margin
Program capacity of 32 ksteps with a sufficient
comment area*2
The program capacity of 32 ksteps, exceeding the capacity of most
compact PLCs, can flexibly handle a wide variety of applications
requiring future equipment expansion.
*2: C14: 16 ksteps
Great Expandability with a Wide
Variety of Options
Max. I/O expansion of 300 points and further expansion
with a function expansion cassette
The add-on cassette easily enables functional enhancements when
slightly more features are to be added, while keeping costs down.
The expansion FP0 adapter enables the connection of 3 additional
FP0 expansion units.
High Security
Program protection with an 8-digit password and a function
prohibiting uploads
USB-port Equipped*3
AFPX-C30
(Add-on cassette attached)
New Functions
Easy-to-use Temperature Control
Command (F356 EZPID)
MEWTOCOL Master Function
AFPX-C14
Ethernet Add-on Unit (Available Soon)
(Add-on cassette attached)
Trace Function
Easy direct connection with a PC via a commercial USB
cable (AB type)
*3: Not provided with C14.
2
3
The Highly Expandable Lineup
Satisfies All Kinds of Needs.
FP-X Name and Function of Each Part
The flexible product lineup designed for rapidly responding to user needs provides a high level of satisfaction.
Control Unit
Product Lineup
Input terminals
Control Unit
Relay output
Power supply (100 to 240 V AC)
DC input: 8 (24 V DC)
Relay output: 6 (250 V AC/2 A)
Program capacity: 16 ksteps
Potentiometer: 2
AFPX-C14R
Power supply (100 to 240 V AC)
DC input: 16 (24 V DC)
Relay output: 14 (250 V AC/2 A)
Program capacity: 32 ksteps
Potentiometer: 2
Equipped with a USB communication port
AFPX-C30R
Power supply (100 to 240 V AC)
DC input: 32 (24 V DC)
Relay output: 28 (250 V AC/2 A)
Program capacity: 32 ksteps
Potentiometer: 4
Equipped with a USB communication port
AFPX-C60R
Transistor output
AFPX-C14TD
DC power supply, Transistor output (NPN), Input: 8-point, Output: 6-point
AFPX-C14T
AC power supply, Transistor output (NPN), Input: 8-point, Output: 6-point
AFPX-C14PD
DC power supply, Transistor output (PNP), Input: 8-point, Output: 6-point
AFPX-C14P
AC power supply, Transistor output (PNP), Input: 8-point, Output: 6-point
AFPX-C30TD
DC power supply, Transistor output (NPN), Input: 16-point, Output: 14-point
AFPX-C30T
AC power supply, Transistor output (NPN), Input: 16-point, Output: 14-point
AFPX-C30PD
DC power supply, Transistor output (PNP), Input: 16-point, Output: 14-point
AFPX-C30P
AC power supply, Transistor output (PNP), Input: 16-point, Output: 14-point
AFPX-C60TD
DC power supply, Transistor output (NPN), Input: 32-point, Output: 28-point
AFPX-C60T
AC power supply, Transistor output (NPN), Input: 32-point, Output: 28-point
AFPX-C60PD
DC power supply, Transistor output (PNP), Input: 32-point, Output: 28-point
AFPX-C60P
AC power supply, Transistor output (PNP), Input: 32-point, Output: 28-point
Expansion Unit
(Model: Relay output type AFPX-C30R)
Power terminals
Expansion cassette interface cover
Connector for
add-on cassette
I/O status monitor LED
Connector for
expansion unit
USB communication port (excluding C14R)
RUN/PROG. mode selection switch
Connector
for battery
Potentiometer
RS232C tool port
24 V DC service power output terminals
C14: 0.15 A
C30, C60: 0.4 A
Connector for expansion unit
Output terminals
(DC powered type has no service power output)
DC input: 8 (24 V DC)
Relay output: 8 (250 V AC/2 A)
AFPX-E16R
Remarks) Two or more E16R can't be
connected serially because it can't
supply the power to other units.
AFPX-E16T
Transistor output (NPN), Input: 8-point, Output: 8-point
AFPX-E16P
Transistor output (PNP), Input: 8-point, Output: 8-point
Expansion Unit
(Model: Relay output type AFPX-E16R)
Power supply (100 to 240 V AC)
DC input: 16 (24 V DC)
Relay output: 14 (250 V AC/2 A)
AFPX-E30R
Remarks) Addition of up to 8 units is possible
including E16R and EFP0.
Add-on Cassette
Communication cassette
AFPX-COM1
Communication cassette (RS232C 1 ch.)
AFPX-COM2
Communication cassette (RS232C 2 ch.)
AFPX-COM3
Communication cassette
(RS485/422 selectable 1 ch.)
AFPX-COM4
Communication cassette
(RS485 1 ch + RS232C 1 ch.)
AFPX-E30TD
DC power supply, Transistor output (NPN), Input: 16-point, Output: 14-point
AFPX-E30T
AC power supply, Transistor output (NPN), Input: 16-point, Output: 14-point
AFPX-E30PD
DC power supply, Transistor output (PNP), Input: 16-point, Output: 14-point
AFPX-E30P
AC power supply, Transistor output (PNP), Input: 16-point, Output: 14-point
AFPX-COM5
(Avail. April 2007)
AFPX-EFP0
Communication cassette
(Ethernet 1 ch + RS232C 1 ch.)
Application cassette
AFPX-IN8
Input cassette (24 V DC , 8 input ch.)
AFPX-TR8
Output cassette
(NPN transistor 0.3 A, 8 output ch.)
AFPX-AD2
Analog input cassette
(12-bit non-insulated 0 to 10 V/0 to 20 mA, 2 ch.)
AFPX-PLS
Pulse I/O cassette
(High-speed counter input: single phase 80 kHz 2 ch.,
2-phase 30 kHz 1 ch.)
(Pulse output: 1 axis 100 kHz < cw/ccw, pulse + sign >)
*Cannot be built into a transistor output type
AFPX-MRTC
I/O status monitor LED
Expansion FP0 Adapter
Up to 3 FP0 expansion units
can be connected.
Master memory cassette with a real-time clock
(32 ksteps program memory +
real-time clock in year/month/day/hour/minute)
*Real-time clock needs an option battery.
(Real-time clock → Calendar timer)
Connector for expansion unit
Connector for expansion unit
FP0 Expansion Unit
Part number
W
NE
Input terminals
Specifications
FP0-E8X
FP0-E16X
FP0-E8YT
FP0-E8YRS
FP0-E16T
FP0-E16P
FP0-E32T
FP0-E32P
FP0-E8RS
FP0-E16RS
8 ch. DC input, MIL connector
FP0-A21
FP0-A80
FP0-A04V
FP0-A04I
FP0-TC4
FP0-TC8
2 ch. analog input, 1 ch. output
FP0-IOL
FP0-CCLS
I/O link unit
FP0-E32RS*1
16ch DC input, 16ch relay output screw terminal block
FP0-RTD6*1
FP0-DPS2*1
6ch RTD input
Output terminals
16 ch. DC input, MIL connector
8 ch. transistor output, MIL connector
8 ch. relay output, screw terminal block
16 ch. transistor output, MIL connector
16 ch. PNP output, MIL connector
16 ch. DC input, 16 ch. transistor output, MIL connector
Add-on Cassette
16 ch. DC input, 16 ch. PNP output, MIL connector
(Model: Analog input cassette AFPX-AD2)
4 ch. DC input, 4 ch. relay output, screw terminal block
Securing hole
8 ch. DC input, 8 ch. relay output, screw terminal block
8 ch. analog input
4 ch. analog (voltage) output
Connector for double-stacked mounting
* Only the communication cassette can be upper.
* Use the two opposite diagonal holes
for mounting when a communication
cassette is double-stacked.
4 ch. analog (current) output
4 ch. thermocouple input
8 ch. thermocouple input
CC-Link unit
Input/output terminals or communication signal terminals
PROFIBUS remote I/O unit
*1 Provided from Panasonic Electric Works Europe AG
4
5
The Highly Expandable Lineup
Satisfies All Kinds of Needs.
FP-X Name and Function of Each Part
The flexible product lineup designed for rapidly responding to user needs provides a high level of satisfaction.
Control Unit
Product Lineup
Input terminals
Control Unit
Relay output
AFPX-C14R
AFPX-C30R
AFPX-C60R
Power supply (100 to 240 V AC)
DC input: 8 (24 V DC)
Relay output: 6 (250 V AC/2 A)
Program capacity: 16 ksteps
Potentiometer: 2
Power supply (100 to 240 V AC)
DC input: 16 (24 V DC)
Relay output: 14 (250 V AC/2 A)
Program capacity: 32 ksteps
Potentiometer: 2
Equipped with a USB communication port
Power supply (100 to 240 V AC)
DC input: 32 (24 V DC)
Relay output: 28 (250 V AC/2 A)
Program capacity: 32 ksteps
Potentiometer: 4
Equipped with a USB communication port
Transistor output
AFPX-C14TD
DC power supply, Transistor output (NPN), Input: 8-point, Output: 6-point
AFPX-C14T
AC power supply, Transistor output (NPN), Input: 8-point, Output: 6-point
AFPX-C14PD
DC power supply, Transistor output (PNP), Input: 8-point, Output: 6-point
AFPX-C14P
AC power supply, Transistor output (PNP), Input: 8-point, Output: 6-point
AFPX-C30TD
DC power supply, Transistor output (NPN), Input: 16-point, Output: 14-point
AFPX-C30T
AC power supply, Transistor output (NPN), Input: 16-point, Output: 14-point
AFPX-C30PD
DC power supply, Transistor output (PNP), Input: 16-point, Output: 14-point
AFPX-C30P
AC power supply, Transistor output (PNP), Input: 16-point, Output: 14-point
AFPX-C60TD
DC power supply, Transistor output (NPN), Input: 32-point, Output: 28-point
AFPX-C60T
AC power supply, Transistor output (NPN), Input: 32-point, Output: 28-point
AFPX-C60PD
DC power supply, Transistor output (PNP), Input: 32-point, Output: 28-point
AFPX-C60P
AC power supply, Transistor output (PNP), Input: 32-point, Output: 28-point
Expansion Unit
(Model: Relay output type AFPX-C30R)
Power terminals
Expansion cassette interface cover
Connector for
add-on cassette
I/O status monitor LED
Connector for
expansion unit
USB communication port (excluding C14R)
RUN/PROG. mode selection switch
Connector
for battery
Potentiometer
RS232C tool port
24 V DC service power output terminals
C14: 0.15 A
C30, C60: 0.4 A
Connector for expansion unit
Output terminals
(DC powered type has no service power output)
AFPX-E16R
DC input: 8 (24 V DC)
Relay output: 8 (250 V AC/2 A)
Remarks) Two or more E16R can't be
connected serially because it can't
supply the power to other units.
AFPX-E16T
Transistor output (NPN), Input: 8-point, Output: 8-point
AFPX-E16P
Transistor output (PNP), Input: 8-point, Output: 8-point
Expansion Unit
(Model: Relay output type AFPX-E16R)
AFPX-E30R
Power supply (100 to 240 V AC)
DC input: 16 (24 V DC)
Relay output: 14 (250 V AC/2 A)
Remarks) Addition of up to 8 units is possible
including E16R and EFP0.
Add-on Cassette
Communication cassette
AFPX-COM1
Communication cassette (RS232C 1 ch.)
AFPX-COM2
Communication cassette (RS232C 2 ch.)
AFPX-COM3
Communication cassette
(RS485/422 selectable 1 ch.)
AFPX-COM4
Communication cassette
(RS485 1 ch + RS232C 1 ch.)
AFPX-E30TD
DC power supply, Transistor output (NPN), Input: 16-point, Output: 14-point
AFPX-E30T
AC power supply, Transistor output (NPN), Input: 16-point, Output: 14-point
AFPX-E30PD
DC power supply, Transistor output (PNP), Input: 16-point, Output: 14-point
AFPX-E30P
AC power supply, Transistor output (PNP), Input: 16-point, Output: 14-point
AFPX-COM5
AFPX-EFP0
Communication cassette
(Introduced soon) (Ethernet 1 ch + RS232C 1 ch.)
Application cassette
AFPX-IN8
Input cassette (24 V DC , 8 input ch.)
AFPX-TR8
Output cassette
(NPN transistor 0.3 A, 8 output ch.)
AFPX-AD2
Analog input cassette
(12-bit non-insulated 0 to 10 V/0 to 20 mA, 2 ch.)
AFPX-PLS
Pulse I/O cassette
(High-speed counter input: single phase 80 kHz 2 ch.,
2-phase 30 kHz 1 ch.)
(Pulse output: 1 axis 100 kHz < cw/ccw, pulse + sign >)
*Cannot be built into a transistor output type
AFPX-MRTC
I/O status monitor LED
Expansion FP0 Adapter
Up to 3 FP0 expansion units
can be connected.
Master memory cassette with a real-time clock
(32 ksteps program memory +
real-time clock in year/month/day/hour/minute)
*Real-time clock needs an option battery.
(Real-time clock → Calendar timer)
Connector for expansion unit
Connector for expansion unit
FP0 Expansion Unit
Part number
W
NE
Input terminals
Specifications
FP0-E8X
FP0-E16X
FP0-E8YT
FP0-E8YRS
FP0-E16T
FP0-E16P
FP0-E32T
FP0-E32P
FP0-E8RS
FP0-E16RS
8 ch. DC input, MIL connector
FP0-A21
FP0-A80
FP0-A04V
FP0-A04I
FP0-TC4
FP0-TC8
2 ch. analog input, 1 ch. output
FP0-IOL
FP0-CCLS
I/O link unit
FP0-E32RS*1
16ch DC input, 16ch relay output screw terminal block
FP0-RTD6*1
FP0-DPS2*1
6ch RTD input
Output terminals
16 ch. DC input, MIL connector
8 ch. transistor output, MIL connector
8 ch. relay output, screw terminal block
16 ch. transistor output, MIL connector
16 ch. PNP output, MIL connector
16 ch. DC input, 16 ch. transistor output, MIL connector
Add-on Cassette
16 ch. DC input, 16 ch. PNP output, MIL connector
(Model: Analog input cassette AFPX-AD2)
4 ch. DC input, 4 ch. relay output, screw terminal block
Securing hole
8 ch. DC input, 8 ch. relay output, screw terminal block
8 ch. analog input
4 ch. analog (voltage) output
Connector for double-stacked mounting
* Only the communication cassette can be upper.
* Use the two opposite diagonal holes
for mounting when a communication
cassette is double-stacked.
4 ch. analog (current) output
4 ch. thermocouple input
8 ch. thermocouple input
CC-Link unit
Input/output terminals or communication signal terminals
PROFIBUS remote I/O unit
*1 Provided from Panasonic Electric Works Europe AG
4
5
Positioning
Usability
FP-X perfectly fits the need for low cost “multi-axis positioning control
The enhanced functionality expands the ranges of applications,
in small-scale equipment”
while improving the ease of use.
■ Built-in 4-axis Pulse Output (Transistor Output Type)
■ Securing 0.5A in every transistor output even when all output ports are ON.
The transistor output type C14 comes with 3-axis while C30/60 comes with 4-axis
pulse output inside the control unit. The multi-axis control, which previously
required a higher-level PLC or additional positioning unit, or two or more PLC units,
can now be achieved with only one FP-X transistor output type unit in a small
space at a low cost. In addition, as this type does not require a pulse I/O cassette
needed for a relay output type, other function expansion cassettes such as
communication or analog input can be attached for more diversified applications.
XY Table + Processing Head
Item
Specification
Pulse Output
C14: 100kHz(CH0,1), 20kHz(CH2)
Max Frequency C30,C60: 100kHz(CH0,1), 20kHz(CH2,3)
Output Type
Function
Semiconductor Wafer Takeout Blade
The transistor output type is not limited by the control capacity of each common
line. Every output port can secure 0.5A even when all output ports are ON for any
basic unit C14, C30, C40 as well as the expansion units E16 and E30 (at 25°C) –
Sufficient capacity for high-load switching such as LED type signal tower etc.
CW+CCW, Pulse + Direction Output
Trapezoidal control, multi-stage
operation, jog operation, origin return,
2-axis linear interpolation
LED signal tower
● The relay output type can control two axes by
using the expansion cassettes
100kHz x
2 axes
20kHz x
2 axes
3-axis Control with C14.
First
axis
80kHz
4-axis Control with C30/C60
Second
axis
80kHz
Pulse output up to 2-axis
80kHz is possible by
loading two pulse I/O
cassettes (AFPX-PLS).
Also capable of
performing 2-axis linear
interpolation.
Pulse I/O cassette doesn’t
work with control unit
transistor output type.
■ 2-axis Linear Interpolation Simultaneously in two Sets (Transistor Output Type)
2-axis linear interpolation refers to moving a robot arm or equipment head diagonally on a straight line by
simultaneously controlling two motor shafts. It is used for palletizing, component pick and place, XY table
control, contour cutting of a PC board etc. FP-X transistor output type is capable of simultaneously
controlling 2-axis linear interpolation, for the first time in the industry with a compact pulse-output PLC.
This unit drastically expands the range of applications along with the added convenience of programming
by using the linear interpolation commands F175 (SPSH).
Transistor Output Capacity 0.5A
(Even when all output ports are ON)
■ Equipped with a Sampling Trace Function – Smart Solution for Program Debugging
(Available from Ver. 2.0 of the transistor type and relay output types)
The sampling trace function enables the user to monitor a change of I/O condition or
data register value in a very short time interval – an efficiency tool for debugging a
ladder program.
The shortest sampling interval of the normal time-chart monitor is 10ms with the FPWIN
GR or FPWIN PRO, but monitoring in much shorter intervals is often required during
debugging operations. The sampling trace function enables data accumulation of any
16 contact data and 3 data register values once or several times within a scan time.
Reading out these data through the FPWIN GR or FPWIN PRO enables the user to
confirm an instantaneous change of status by time on the time-chart monitor.
(Normal Time-Chart Monitor)
(Sampling Trace)
Controls Two Units of 2-axis XY Table
C30/C60
Simultaneous Control of Two Mechanisms
Invisible changes become visible!
Y-axis Maximum
(CH1) composite speed
100kHz
Maximum
Y-axis composite speed
(CH3) 20kHz
■ The communication cassette (Ethernet Type) will be available soon.
X-axis
(CH2)
X-axis (CH0)
● The relay output type is also capable of 2-axis linear interpolation.
By adding two pulse I/O cassette units, linear interpolation is
possible at the maximum composite speed of 80kHz. The
command used for this unit is F175 (SPSH), same as that for
the transistor output types.
Using this option, you can monitor the data in FP-X on the
PCWAY through the existing Ethernet, or remotely
upload/download a program.
Model Type
Transistor
Output Mode Pulse Output (four axes) One ch in use
Single Phase
Output Type
Dual Phase
Relay Output
Single Phase
Type
Dual Phase
10BASE-T, 100BASE-TX, TCP/IP
RS232C (COM2)
3-wire, Asynchronous, Max115.2kbps
Computer Link
General communication General communication
(server)
(client)
Ethernet
Communication
PCWAY,
Mode
(1:1 communication) FPWIN GR/PRO
etc.
AFPX-COM5
■ High-Speed Counters – Eight Built–in Sets
Eight single-phase or four dual-phase
sets (X0~X7)
Ethernet (COM1)
Interface
Wait for a connection Connect to the
by the partner
specified partner
FP-X
FP-X
All channels in use
During Halt
100kHz
50kHz × 4ch + 10kHz × 4ch
During Operation
35kHz
25kHz × 4ch + 10kHz × 4ch
During Halt
35kHz
25kHz × 2ch + 5kHz × 2ch
During Operation
15kHz
10kHz × 2ch + 5kHz × 2ch
During Halt
10kHz
10kHz × 8ch
During Operation
10kHz
10kHz × 8ch
During Halt
5kHz
5kHz × 4ch
During Operation
5kHz
5kHz × 4ch
PCWAY
FPWIN GR/PRO
FP-X
Ethernet
Computer Link*
General Communication
Ethernet RS232C
FP-X
FP-X
*Computer Link is the command-response type
communication method using Matsushita’s
open protocol MEWTOCOL.
When adding a pulse I/O cassette to the relay output type, two high-speed counter sets can
be added to every cassette. Please refer to the user manual for counter specification.
6
7
Positioning
Usability
FP-X perfectly fits the need for low cost “multi-axis positioning control
The enhanced functionality expands the ranges of applications,
in small-scale equipment”
while improving the ease of use.
■ Built-in 4-axis Pulse Output (Transistor Output Type)
■ Securing 0.5A in every transistor output even when all output ports are ON.
The transistor output type C14 comes with 3-axis while C30/40 comes with 4-axis
pulse output inside the control unit. The multi-axis control, which previously
required a higher-level PLC or additional positioning unit, or two or more PLC units,
can now be achieved with only one FP-X transistor output type unit in a small
space at a low cost. In addition, as this type does not require a pulse I/O cassette
needed for a relay output type, other function expansion cassettes such as
communication or analog input can be attached for more diversified applications.
XY Table + Processing Head
Item
Specification
Pulse Output
C14: 100kHz(CH0,1), 20kHz(CH2)
Max Frequency C30,C60: 100kHz(CH0,1), 20kHz(CH2,3)
Output Type
Function
Semiconductor Wafer Takeout Blade
The transistor output type is not limited by the control capacity of each common
line. Every output port can secure 0.5A even when all output ports are ON for any
basic unit C14, C30, C60 as well as the expansion units E16 and E30 (at 25° C) –
Sufficient capacity for high-load switching such as LED type signal tower etc.
CW+CCW, Pulse + Direction Output
Trapezoidal control, multi-stage
operation, jog operation, origin return,
2-axis linear interpolation
LED signal tower
● The relay output type can control two axes by
using the expansion cassettes
100kHz x
2 axes
20kHz x
2 axes
3-axis Control with C14.
First
axis
80kHz
4-axis Control with C30/C60
Second
axis
80kHz
Pulse output up to 2-axis
80kHz is possible by
loading two pulse I/O
cassettes (AFPX-PLS).
Also capable of
performing 2-axis linear
interpolation.
Pulse I/O cassette doesn’t
work with control unit
transistor output type.
■ 2-axis Linear Interpolation Simultaneously in two Sets (Transistor Output Type)
2-axis linear interpolation refers to moving a robot arm or equipment head diagonally on a straight line by
simultaneously controlling two motor shafts. It is used for palletizing, component pick and place, XY table
control, contour cutting of a PC board etc. FP-X transistor output type is capable of simultaneously
controlling 2-axis linear interpolation, for the first time in the industry with a compact pulse-output PLC.
This unit drastically expands the range of applications along with the added convenience of programming
by using the linear interpolation commands F175 (SPSH).
Transistor Output Capacity 0.5A
(Even when all output ports are ON)
■ Equipped with a Sampling Trace Function – Smart Solution for Program Debugging
(Available from Ver. 2.0 of the transistor type and relay output types)
The sampling trace function enables the user to monitor a change of I/O condition or
data register value in a very short time interval – an efficiency tool for debugging a
ladder program.
The shortest sampling interval of the normal time-chart monitor is 10ms with the FPWIN
GR or FPWIN PRO, but monitoring in much shorter intervals is often required during
debugging operations. The sampling trace function enables data accumulation of any
16 contact data and 3 data register values once or several times within a scan time.
Reading out these data through the FPWIN GR or FPWIN PRO enables the user to
confirm an instantaneous change of status by time on the time-chart monitor.
(Normal Time-Chart Monitor)
(Sampling Trace)
Controls Two Units of 2-axis XY Table
C30/C60
Simultaneous Control of Two Mechanisms
Invisible changes become visible!
Y-axis Maximum
(CH1) composite speed
100kHz
Maximum
Y-axis composite speed
(CH3) 20kHz
■ The communication cassette (Ethernet Type) will be April 2007.
X-axis
(CH2)
X-axis (CH0)
● The relay output type is also capable of 2-axis linear interpolation.
By adding two pulse I/O cassette units, linear interpolation is
possible at the maximum composite speed of 80kHz. The
command used for this unit is F175 (SPSH), same as that for
the transistor output types.
Using this option, you can monitor the data in FP-X on the
PCWAY through the existing Ethernet, or remotely
upload/download a program.
Model Type
Transistor
Output Mode Pulse Output (four axes) One ch in use
Single Phase
Output Type
Dual Phase
Relay Output
Single Phase
Type
Dual Phase
10BASE-T, 100BASE-TX, TCP/IP
RS232C (COM2)
3-wire, Asynchronous, Max115.2kbps
Computer Link
General communication General communication
(server)
(client)
Ethernet
Communication
PCWAY,
Mode
(1:1 communication) FPWIN GR/PRO
etc.
AFPX-COM5
■ High-Speed Counters – Eight Built–in Sets
Eight single-phase or four dual-phase
sets (X0~X7)
Ethernet (COM1)
Interface
Wait for a connection Connect to the
by the partner
specified partner
FP-X
FP-X
All channels in use
During Halt
100kHz
50kHz × 4ch + 10kHz × 4ch
During Operation
35kHz
25kHz × 4ch + 10kHz × 4ch
During Halt
35kHz
25kHz × 2ch + 5kHz × 2ch
During Operation
15kHz
10kHz × 2ch + 5kHz × 2ch
During Halt
10kHz
10kHz × 8ch
During Operation
10kHz
10kHz × 8ch
During Halt
5kHz
5kHz × 4ch
During Operation
5kHz
5kHz × 4ch
PCWAY
FPWIN GR/PRO
FP-X
Ethernet
Computer Link*
General Communication
Ethernet RS232C
FP-X
FP-X
*Computer Link is the command-response type
communication method using Matsushita’s
open protocol MEWTOCOL.
When adding a pulse I/O cassette to the relay output type, two high-speed counter sets can
be added to every cassette. Please refer to the user manual for counter specification.
6
7
Temperature Control
High capacity/High speed
The high-level PID control easily achieves high-speed, high-accuracy
The high-level basic performance provides sufficient room for future
multi-point temperature control.
equipment expansion as well as a rich variation.
■ New PID Command (F356 EZPID) Produces a Temperature
Control Program only in a Single Line.
■ Abundant program capacity -
●The application of PLC-based temperature control has been
expanding such as multi-level temperature control, timercontrolled temperature control, and a temperature control
relative to a variable based on a data computation results
etc. By using the new PID command (F356 EZPID), a PID
control program can be drastically simplified and the PLCbased temperature control, which was previously thought
to be difficult by a PLC, can easily be achieved. The
example on the right, a simple uniform temperature control,
enables a surprisingly easily PID control with a single line
command by using a F356 command combined with a
touch-panel operation.
Thermocouple *1
°C
Touch Panel
Parameter setup
• Target value
• Control code
• PID control elements
Start bit ON
Auto-tuning end
■ Ultra high-speed scan at
Program
Start bit OFF
Parameter storage
Heater
Only a
single
command
PWM output
frequency setup
R0
PWM output circuit
*1 Thermocouple connection requires FP0 Thermocouple Unit.
Y0
F356 EZPID, WR1,
WX1,
DT0,
16k
FP0
10k
10k
0.32 µsec for instruction processing
20k
30k
Scan time: 1.9
steps
●Processing speed of the basic
instructions (ST, OR, AND, OT etc)
FP-X
0.32 µsec
0.9 µsec
FP0
ms (measured time)
DT100
Control code Measured value Target value Output value
PWM output
C14
(Ex.) In the case of a 5-kstep program consisting of 35% basic
instructions and 65% applied instructions,
Timer set value
conversion
t
PWM output
FP-X
C14
High-speed processing is often required for small-scale equipment control
such as serial data communication, network construction or PID temperature
control. High-speed scanning at 0.32 µsec/step (basic instruction) easily meets
such requirements.
Executing F356 PID command
PID command execution
Bit processing
SSR
32k
● 100,000 I/O comment items, 5,000 lines of line-space comments, 5,000 lines of remark
comments - All comments are stored in the FP-X simultaneously with the program.
• Target value setup
• Auto-tuning execution
C30/C60
C30, C60
● Separate memory areas reserved for program memory and comments do not cause a
reduction of program capacity when comments are entered.
Auto-tuning setup
Constant Temperature
●Program capacity
FP-X
The program capacity of 32 ksteps, exceeding the capacity of most compact
PLCs, can flexibly handle a wide variety of applications requiring future
equipment expansion. An adequate comment area has of course been
reserved. Free comment entry makes the program easy to understand during
verification.
When using the new
F356 PID command
When using the
previous F355 command
32 ksteps (16 ksteps for C14)
1.0 µsec
0.5
Output address
■ Abundant number of I/O points - Maximum
300
(Up to 382 points possible by using FP0 expansion units and add-on cassettes)
■ Multi-point PID control
When the user cannot predict the number of I/O points required in the future for his machine or equipment, he
is uncertain in selecting a PLC model. FP-X solves user concerns with a maximum of 300 I/O channels. The
number can even be increased up to 382 points by using the add-on cassettes and FP0 expansion units.
●High-accuracy PID control is possible by adopting a sophisticated
algorithm and floating-point operations.
●Higher accuracy is obtained by ultra high-speed computations in a
32 µs/loop. For example, a 16-loop control only adds a scan time of
0.5 ms by ensuring minimum impact on the tact time.
●The simultaneous multi-point auto-tuning simplifies complex
parameter setting.
●The high-speed control PI-D*1 mode and overshoot suppression I-PD*2
mode are available for selection according to the intended application.
●By combining with a sequence control, the parameters (Kp, Ti, Td, etc.)
can be changed during a PID control execution, thereby enabling
optimum temperature control in each stage including start up, midrange, and convergence.
The ability to change the target value easily enables multi-step
temperature control, which was difficult only with temperature
controllers. In addition, the multi-point temperature control enables
the centralized control of multiple temperature controllers with a
single FP-X for unified data management.
C60
E30
E30
E30
Max. 300 channels
Multiple temperature
controllers
Easy unification of
data management
Max. 8 units
FP-X
● Two or more E16 can't be connected serially.
T/C
T/C
T/C
T/C
T/C
C60
E16
● E16 can be sandwiched with E30*
E16
C60
Partial optimum control by changing parameters
E30
Multi-step control by changing the target value
NG
OK
* E30 requires an external power supply
High-speed PID
control
PI-D mode
Target value
● Connection by using the cable included in each expansion unit.
Target
value
Target
value
C60
I-PD mode
Rapid acceleration
Smooth startup
Time
Time
E30
E30
The units can be tightly
mounted adjacent to each
other with the cable bent
inside between the units for
saving space.
Overshoot suppression
8
E16
For connecting a thermocouple, please use an FP0 thermocouple
unit via an adapter (AFPX-EFP0).
*1 Derivative type
*2 Proportional-derivative type
Two modes are selectable
● Expansion units (E16R, E30R, EFP0) can be connected up to eight units.
Modbus-RTU
Time
9
Temperature Control
High capacity/High speed
The high-level PID control easily achieves high-speed, high-accuracy
The high-level basic performance provides sufficient room for future
multi-point temperature control.
equipment expansion as well as a rich variation.
■ New PID Command (F356 EZPID) Produces a Temperature
Control Program only in a Single Line.
■ Abundant program capacity -
●The application of PLC-based temperature control has been
expanding such as multi-level temperature control, timercontrolled temperature control, and a temperature control
relative to a variable based on a data computation results
etc. By using the new PID command (F356 EZPID), a PID
control program can be drastically simplified and the PLCbased temperature control, which was previously thought
to be difficult by a PLC, can easily be achieved. The
example on the right, a simple uniform temperature control,
enables a surprisingly easily PID control with a single line
command by using a F356 command combined with a
touch-panel operation.
Thermocouple *1
°C
Touch Panel
Parameter setup
• Target value
• Control code
• PID control elements
Start bit ON
Auto-tuning end
■ Ultra high-speed scan at
Program
Start bit OFF
Parameter storage
Heater
Only a
single
command
PWM output
frequency setup
R0
PWM output circuit
*1 Thermocouple connection requires FP0 Thermocouple Unit.
Y0
F356 EZPID, WR1,
WX1,
DT0,
16k
FP0
10k
10k
0.32 µsec for instruction processing
20k
30k
Scan time: 1.9
steps
●Processing speed of the basic
instructions (ST, OR, AND, OT etc)
FP-X
0.32 µsec
0.9 µsec
FP0
ms (measured time)
DT100
Control code Measured value Target value Output value
PWM output
C14
(Ex.) In the case of a 5-kstep program consisting of 35% basic
instructions and 65% applied instructions,
Timer set value
conversion
t
PWM output
FP-X
C14
High-speed processing is often required for small-scale equipment control
such as serial data communication, network construction or PID temperature
control. High-speed scanning at 0.32 µsec/step (basic instruction) easily meets
such requirements.
Executing F356 PID command
PID command execution
Bit processing
SSR
32k
● 100,000 I/O comment items, 5,000 lines of line-space comments, 5,000 lines of remark
comments - All comments are stored in the FP-X simultaneously with the program.
• Target value setup
• Auto-tuning execution
C30/C60
C30, C60
● Separate memory areas reserved for program memory and comments do not cause a
reduction of program capacity when comments are entered.
Auto-tuning setup
Constant Temperature
●Program capacity
FP-X
The program capacity of 32 ksteps, exceeding the capacity of most compact
PLCs, can flexibly handle a wide variety of applications requiring future
equipment expansion. An adequate comment area has of course been
reserved. Free comment entry makes the program easy to understand during
verification.
When using the new
F356 PID command
When using the
previous F355 command
32 ksteps (16 ksteps for C14)
1.0 µsec
0.5
Output address
■ Abundant number of I/O points - Maximum
300
(Up to 382 points possible by using FP0 expansion units and add-on cassettes)
■ Multi-point PID control
When the user cannot predict the number of I/O points required in the future for his machine or equipment, he
is uncertain in selecting a PLC model. FP-X solves user concerns with a maximum of 300 I/O channels. The
number can even be increased up to 382 points by using the add-on cassettes and FP0 expansion units.
●High-accuracy PID control is possible by adopting a sophisticated
algorithm and floating-point operations.
●Higher accuracy is obtained by ultra high-speed computations in a
32 µs/loop. For example, a 16-loop control only adds a scan time of
0.5 ms by ensuring minimum impact on the tact time.
●The simultaneous multi-point auto-tuning simplifies complex
parameter setting.
●The high-speed control PI-D*1 mode and overshoot suppression I-PD*2
mode are available for selection according to the intended application.
●By combining with a sequence control, the parameters (Kp, Ti, Td, etc.)
can be changed during a PID control execution, thereby enabling
optimum temperature control in each stage including start up, midrange, and convergence.
The ability to change the target value easily enables multi-step
temperature control, which was difficult only with temperature
controllers. In addition, the multi-point temperature control enables
the centralized control of multiple temperature controllers with a
single FP-X for unified data management.
C60
E30
E30
E30
Max. 300 channels
Multiple temperature
controllers
Easy unification of
data management
Max. 8 units
FP-X
● Two or more E16 can't be connected serially.
T/C
T/C
T/C
T/C
T/C
C60
E16
● E16 can be sandwiched with E30*
E16
C60
Partial optimum control by changing parameters
E30
Multi-step control by changing the target value
NG
OK
* E30 requires an external power supply
High-speed PID
control
PI-D mode
Target value
● Connection by using the cable included in each expansion unit.
Target
value
Target
value
C60
I-PD mode
Rapid acceleration
Smooth startup
Time
Time
E30
E30
The units can be tightly
mounted adjacent to each
other with the cable bent
inside between the units for
saving space.
Overshoot suppression
8
E16
For connecting a thermocouple, please use an FP0 thermocouple
unit via an adapter (AFPX-EFP0).
*1 Derivative type
*2 Proportional-derivative type
Two modes are selectable
● Expansion units (E16R, E30R, EFP0) can be connected up to eight units.
Modbus-RTU
Time
9
Expansion
Network
"Require slightly more functions", "Want to add functions to the existing equipment"
Different types of equipment need to be linked − FP-X flexibly meet such requirements.
- The rich variety of expansion boards helps solve these requirements.
■ MEWTOCOL Master Function Has Been Added
Add-on cassette easily adds small quantities of functions and I/O points.
The add-on cassette can be mounted onto the control unit easily.
Up to 2 cassettes on C14 or up to 3 cassettes on C30/C60 can be mounted.
Only communication cassette can be double-stacked upper side. (Communication cassette should be only one totally.)
Note) Please refer to the manual for the number of mountable units and position.
Add-on Cassette
DC input
AFPX-IN8
24 V DC input, 8 ch., bidirectional input (sync/source)
Application Cassette
Analog input
AFPX-AD2
2 ch., 12 bits (non-insulated), 2 ms/2 ch.
0 to 10 V or 0 to 20 mA
Master memory
AFPX-MPTC
32-kstep program storage and transfer
Calendar timer
Communication
Cassette
Cannot be used with a
transistor output type
High-speed counter input
➔ Single-phase 2 ch. 80 kHz or two-phase
1 ch. 30 kHz
Pulse output
➔ Single-axis 100 kHz (CW/CCW, Pulse+Sign)
NE
W
PC
RS232C
AFPX-COM3
RS485/RS422 selectable
AFPX-COM4
RS485 + RS232C*1
AFPX-COM5
Ethernet 1ch + RS232C 1 ch (Available April 2007)
1 ch. each
Easily removable
(Two screws to secure the unit)
FP0 expansion unit.
The MEWNET-W0 allows program-free links of up to 16 PLC units such as
FP2/2SH or FPΣ. The distributed control system allows efficient model
selection.
Item
Specifications
FPΣ requires a communication cassette (AFPG803, AFPG806)
E30
■ Modbus* Compatibility
Max. 7 units (210 points)
Product number
●Simple setting of the number of linked units, linked relays, and starting
Transmission speed
115.2 kbps
area address of the own station by using FPWIN GR/Pro allows sharing
Transmission distance
1200 m
of contact information and data without programming.
128 words (data register), 64 words (contacts)
Shared data
●The transfer rate of 115.2 kbps, the highest rate for a compact model.
Communication method Floating master
●A transfer distance of 1200 m, the longest distance for a compact model.
●FP-X and FPΣ allow a change of the station number by programming
(SYS instruction).
16 stations, 115.2 kbps, 1200 m
RS485
Twisted-pair cable
FP2/2SH requires a multi-communication unit (AFP2465, AFP2805)
Expansion FP0 adapter (AFPX-EFP0)
Specifications
16 stations
FP-X requires a communication cassette (AFPX-COM3 or AFPX-COM4)
* Only one expansion FP0 adapter unit can be attached to a control unit.
Up to 7 FP-X expansion units can be used when the expansion FP0 adapter is attached.
Max. 96 points
Compatible with both the master and slave of the Modbus* RTU, the world's de-facto standard
Great performance is expected for air-conditioning, temperature controls etc.
* Protocol developed by the Modicon Inc. of the United States
Usable as a master station [F145 (Write), F146 (Read) commands]
Capable of easily communicating with a temperature controller, inverter, FP-e, and foreign PLC
Specifications
FP0-A21
FP0-A80
FP0-A04V
FP0-A04I
FP0-TC4
FP0-TC8
Analog 2 ch. input, 1 ch. output
Analog 8 ch. input
Analog (voltage) 4 ch. output
Analog (current) 4 ch. output
Thermocouple 4 ch. input
Thermocouple 8 ch. input
FP0-IOL
FP0-CCL
I/O link unit
CC-link unit
DC input, 16ch relay output
FP0-E32RS*2 16ch
screw terminal block
2
FP0-RTD6*
6ch RTD input
FP0-DPS2*2 PROFIBUS remote I/O unit
*2 Provided from Panasonic Electric Works Europe AG
10
Modbus-RTU (115.2kbps,1200m)
RS485
1 ch.
All control units can be expanded by up to 3 FP0 expansion units via an adapter.
Applications can be expanded by using [Transistor outputs], [Analog input/outputs],
[Thermocouple input] and [I/O link (network)].
When further expansion or functions are required, use the existing FP0 expansion unit.
FP0-E16RS
RS232C
Number of stations
8 ch. DC input, MIL connector
16 ch. DC input, MIL connector
8 ch. transistor output, MIL connector
8 ch. relay output, screw terminal block
16 ch. transistor output, MIL connector
16 ch. DC input, 16 ch. transistor output,
MIL connector
4 ch. DC input, 4 ch. relay output,
screw terminal block
8 ch. DC input, 8 ch. relay output,
screw terminal block
1st ch.
■ PLC Link
2 ch.
E30
Always used
(Port No. COM1)
FP-e (PLC)
Temperature controller etc.
■ When further expansion or functions are required, use the existing
FP0-E8RS
AFPX-COM3 (RS485/422 selectable 1 ch.)
AFPX-COM2 (RS232C 2 ch.)
AFPX-COM4 (RS485+RS232C) 2nd ch. Switch-selectable
(Port No. COM2)
USB port
Default setting: USB port use
1 ch.
*1: Each of RS485 and RS422 is an insulated type.
FP0-E32T
Always used
AFPX-COM1 (RS232C 1 ch.)
GT11
AFPX-COM2
Product number
FP0-E8X
FP0-E16X
FP0-E8YT
FP0-E8YRS
FP0-E16YT
Communication Port
RS232C tool port
USB
RS232C
C60
■ Up to 3 serial communication ports can be used at once.
Communication cassette
AFPX-COM1
*1
Eco-POWER METER
KW4M
Temperature
Controller
KT4H
*The RS232C tool port can be used as a general-purpose serial communication port.
Transistor output AFPX-TR8 NPN, 8 ch., 0.3 A
Pulse I/O
AFPX-PLS
RS485
The use of a communication cassette provides up to 3 serial
communication ports.
Usable interfaces include RS232C, RS485, RS422, and USB.
Specifications
2D Code Reading Sensor
PD50
RS232C
Communication
cassette
■ The
By using the newly added MEWTOCOL master function for
automatically generating MEWTOCOL (Matsushita Open
Protocol) commands, serial communication with MEWTOCOL
compatible units such as PD50, KT4H, KW4H etc becomes
substantially easier.
Can also be used as
a slave station
Temperature Watt-hour meter
controller
Inverter
Another available application
The unified unit height of 90 mm makes
the panel surface look clean.
When 17 or more FP-X units need to be linked, the use of a Modbus
instead of a MEWNET-W0 can accommodate up to 99 FP-X units.
Because each FP-X can be a master or slave, a multi-master link
can be constructed by passing a token from a user program.
PLC
FP-e
FPΣ
Token passing (by user program)
Master/
slave
Master/
slave
Master/
slave
Master/
slave
Multi-master link of up
to 99 units is possible.
11
Expansion
Network
"Require slightly more functions", "Want to add functions to the existing equipment"
Different types of equipment need to be linked − FP-X flexibly meet such requirements.
- The rich variety of expansion boards helps solve these requirements.
■ MEWTOCOL Master Function Has Been Added
Add-on cassette easily adds small quantities of functions and I/O points.
The add-on cassette can be mounted onto the control unit easily.
Up to 2 cassettes on C14 or up to 3 cassettes on C30/C60 can be mounted.
Only communication cassette can be double-stacked upper side. (Communication cassette should be only one totally.)
Note) Please refer to the manual for the number of mountable units and position.
Add-on Cassette
DC input
AFPX-IN8
24 V DC input, 8 ch., bidirectional input (sync/source)
Application Cassette
Analog input
AFPX-AD2
2 ch., 12 bits (non-insulated), 2 ms/2 ch.
0 to 10 V or 0 to 20 mA
Master memory
AFPX-MPTC
32-kstep program storage and transfer
Calendar timer
Communication
Cassette
Cannot be used with a
transistor output type
High-speed counter input
➔ Single-phase 2 ch. 80 kHz or two-phase
1 ch. 30 kHz
Pulse output
➔ Single-axis 100 kHz (CW/CCW, Pulse+Sign)
NE
W
RS232C
AFPX-COM2
RS232C
AFPX-COM3
RS485/RS422 selectable
AFPX-COM4
RS485 + RS232C*1
AFPX-COM5
Ethernet 1ch + RS232C 1 ch (Introduced soon)
PC
1 ch.
1 ch. each
Easily removable
(Two screws to secure the unit)
FP0 expansion unit.
Item
Specifications
Specifications
Product number
16 stations
●Simple setting of the number of linked units, linked relays, and starting
Transmission speed
115.2 kbps
area address of the own station by using FPWIN GR/Pro allows sharing
Transmission distance
1200 m
of contact information and data without programming.
128 words (data register), 64 words (contacts)
Shared data
●The transfer rate of 115.2 kbps, the highest rate for a compact model.
Communication method Floating master
●A transfer distance of 1200 m, the longest distance for a compact model.
●FP-X and FPΣ allow a change of the station number by programming
(SYS instruction).
16 stations, 115.2 kbps, 1200 m
RS485
Twisted-pair cable
FP2/2SH requires a multi-communication unit (AFP2465, AFP2805)
FPΣ requires a communication cassette (AFPG803, AFPG806)
■ Modbus* Compatibility
Max. 96 points
Compatible with both the master and slave of the Modbus* RTU, the world's de-facto standard
Great performance is expected for air-conditioning, temperature controls etc.
* Protocol developed by the Modicon Inc. of the United States
Usable as a master station [F145 (Write), F146 (Read) commands]
Capable of easily communicating with a temperature controller, inverter, FP-e, and foreign PLC
Specifications
FP0-A21
FP0-A80
FP0-A04V
FP0-A04I
FP0-TC4
FP0-TC8
Analog 2 ch. input, 1 ch. output
Analog 8 ch. input
Analog (voltage) 4 ch. output
Analog (current) 4 ch. output
Thermocouple 4 ch. input
Thermocouple 8 ch. input
FP0-IOL
FP0-CCL
I/O link unit
CC-link unit
DC input, 16ch relay output
FP0-E32RS*2 16ch
screw terminal block
2
FP0-RTD6*
6ch RTD input
FP0-DPS2*2 PROFIBUS remote I/O unit
*2 Provided from Panasonic Electric Works Europe AG
10
The MEWNET-W0 allows program-free links of up to 16 PLC units such as
FP2/2SH or FPΣ. The distributed control system allows efficient model
selection.
FP-X requires a communication cassette (AFPX-COM3 or AFPX-COM4)
E30
Max. 7 units (210 points)
8 ch. DC input, MIL connector
16 ch. DC input, MIL connector
8 ch. transistor output, MIL connector
8 ch. relay output, screw terminal block
16 ch. transistor output, MIL connector
16 ch. DC input, 16 ch. transistor output,
MIL connector
4 ch. DC input, 4 ch. relay output,
screw terminal block
8 ch. DC input, 8 ch. relay output,
screw terminal block
1st ch.
Modbus-RTU (115.2kbps,1200m)
RS485
Number of stations
E30
Always used
(Port No. COM1)
■ PLC Link
2 ch.
Expansion FP0 adapter (AFPX-EFP0)
FP0-E16RS
AFPX-COM3 (RS485/422 selectable 1 ch.)
AFPX-COM2 (RS232C 2 ch.)
GT11
* Only one expansion FP0 adapter unit can be attached to a control unit.
Up to 7 FP-X expansion units can be used when the expansion FP0 adapter is attached.
FP0-E8RS
RS232C
1 ch.
All control units can be expanded by up to 3 FP0 expansion units via an adapter.
Applications can be expanded by using [Transistor outputs], [Analog input/outputs],
[Thermocouple input] and [I/O link (network)].
When further expansion or functions are required, use the existing FP0 expansion unit.
FP0-E32T
Always used
AFPX-COM1 (RS232C 1 ch.)
AFPX-COM4 (RS485+RS232C) 2nd ch. Switch-selectable
(Port No. COM2)
USB port
Default setting: USB port use
USB
■ When further expansion or functions are required, use the existing
Product number
FP0-E8X
FP0-E16X
FP0-E8YT
FP0-E8YRS
FP0-E16YT
Communication Port
RS232C tool port
Communication cassette
*1: Each of RS485 and RS422 is an insulated type.
C60
■ Up to 3 serial communication ports can be used at once.
FP-e (PLC)
Temperature controller etc.
AFPX-COM1
*1
Eco-POWER METER
KW4M
Temperature
Controller
KT4H
*The RS232C tool port can be used as a general-purpose serial communication port.
Transistor output AFPX-TR8 NPN, 8 ch., 0.3 A
Pulse I/O
AFPX-PLS
RS485
The use of a communication cassette provides up to 3 serial
communication ports.
Usable interfaces include RS232C, RS485, RS422, and USB.
Specifications
2D Code Reading Sensor
PD50
RS232C
Communication
cassette
■ The
By using the newly added MEWTOCOL master function for
automatically generating MEWTOCOL (Matsushita Open
Protocol) commands, serial communication with MEWTOCOL
compatible units such as PD50, KT4H, KW4H etc becomes
substantially easier.
Can also be used as
a slave station
Temperature Watt-hour meter
controller
Inverter
Another available application
The unified unit height of 90 mm makes
the panel surface look clean.
When 17 or more FP-X units need to be linked, the use of a Modbus
instead of a MEWNET-W0 can accommodate up to 99 FP-X units.
Because each FP-X can be a master or slave, a multi-master link
can be constructed by passing a token from a user program.
PLC
FP-e
FPΣ
Token passing (by user program)
Master/
slave
Master/
slave
Master/
slave
Master/
slave
Multi-master link of up
to 99 units is possible.
11
Program protection
Programming
Note: Product names and company names in this chart are trademarks or registered trademarks of the respective companies.
Protects your important program by preventing
illegal copies
Protected
Protected
Master memory
■ Program upload is easily prohibited by tool
software FPWIN.
Items possible
during an uploadprohibited condition
●Reading a program from the PLC main unit is virtually impossible.
●In the upload-prohibited condition, program transfers to the master
memory are also prohibited.
●Release of an upload-prohibited condition is possible with a forced
release accompanied by a program deletion.
●Program updates are easily carried out by transferring the program in
the master memory to FP-X even during an upload-prohibited condition.
The transferred program in FP-X is setup with the same upload
prohibition and permission conditions used in the master memory.
Program download from a PC
Data transfer from the master
memory
Change of data monitor/resistor value
Contact monitor
Time chart monitor
Items impossible Program upload to a PC
during an upload- Data transfer to the master memory
prohibited condition
Forced input/output
(Original program is required)
Ladder monitor
(Original program is required)
Rewrite during RUN mode
(Original program is required)
Password protection
■ More secure eight-character password can be used
along with the previous four-character password.
●The combination of upper and lower case alphanumeric characters
produces 218 trillion combinations. In addition, after three consecutive
entry failures, a power reset is required for password release.
Control FPWIN GR for Windows
The ladder programming software for FP series − highly operational software tool for maximizing convenience
in the field.
■ Operational Environment
■ Features
1. Easy field operations not requiring the use of a mouse for data
entry, search, writing, monitoring and timer changes, all carried
out only from the keyboard.
2. Allows standard operations in Windows, such as Copy & Paste,
etc.
3. All FP series PLCs are supported. The software assets produced
by using Ver. 4 or Ver. 3 of NPST-GR are usable.
4. Easy programming with wizard functions.
5. Communication with OPC Server, CommX, GTWIN, PCWAY
simultaneously through the same port.
OS
Windows95 (OSR2 or higher)/98/Me/
NT (Ver. 4.0 or later)/2000/XP
Hard disk capacity
At least 40 MB
CPU
Pentium 100 MHz or higher
Onboard memory
At least 64 MB (depends on OS)
Screen resolution
At least 1024 × 768
Display colors
High color (16-bit or higher)
Applicable PLC
FP-X/FP-e/FP0/FPΣ/FP2/FP2SH
Compatible FP-X
version
Relay output type: Ver.2.50 and after
Transistor output type: Ver.2.70 and after
Tool bar
Adaptability
Access often-used functions
using icons.
Program status display
Data monitoring window
Search window
Relay monitoring window
Allows you to search various data
High versatility and rich functionality provides “peace of mind” and “flexibility”.
Function bar
Program display
Bottons for command input
and confirmation, on-line/offline selection and PLC mode
selection.
■ An expensive USB conversion adapter/cable is not necessary for connecting
a PC to the PLC by using a standard USB port.*
In the case of FP-X
Before
PC
RS232C/422 Previous Model
conversion
adapter
USB
conversion cable
* USB port is equipped with C30 and C60.
Function instruction list
I/O comment edit function
USB cable direct
connection
The conventional RS232C port can also be used.
■ The master memory makes a program transfer easy and a real-time clock is equipped also
●The built-in 1 MB flash-ROM can store a 32-kstep program as well as the
comments and FPWIN Pro source file.
●Program update in a remote location is easy by simply sending master
memory for local installation.
●As the master memory stores the password information, password protection can be
applied for program transmission. Similarly, upload prohibition/permission can be setup.
●The built-in real-time clock enables periodical repeated control and
periodical data logging.
■ No need for program backup − easy maintenance
Master memory
To the field
operation
Program
transfer
FPWIN GR/Pro
FP-X
Program
transfer
●The programs and comments are stored in flash ROM, requiring no backup batteries.
●A backup battery is provided for data and real-time clock (AFPX-BATT)
One battery for C14, two for C30 and three for C60 can be attached. A twoBattery
battery installation can operate for a long time (10 years or more) without
holder
maintenance. (Real-time clock doesn't work without a battery.)
FP-X
Password used ➔ Password locked
Upload prohibited set ➔ Upload prohibited
Upload prohibited not set ➔ Upload permitted
●FP-X can store a program, comments, a total of 55 words of data, and
bit setting values in a flash memory without a battery. All of the data
and bits can be stored by adding optional batteries, but writing into a
flash ROM is possible without a battery by using applied instructions
(F12, P13). Perfectly suited for data storage of the setup values and
recipes modified several times a day.
Flash-ROM
* The limitation in a flash ROM designates the number of rewrites to be 10,000, or the feasible number to be approx 30,000. However,
rewriting every second will generate a memory failure within a few hours.
Writing
Classified by type, function
instructions can be selected from
the displayed list.
(Simple help included.)
Displays information concerning
PLC usage situation and settings,
and detailed information when an
error occurs.
■ Accompanying Tools
Text Compiler
Text command input mode
●Data Editor
This software for the PC is for reading and writing data
stored in the memory of FP Series main unit or on an IC
card. If a large data table is required in a PLC, the data
can be created and edited on a PC and then dowmload
to the PLC.
●Modem connection
Connector
Communication via modem is easy with FP Series units
in isolated locations.
Backup battery
for FP-X
(AFPX-BATT)
F12 ICRD K0, K1, DT0
Reading
Successive I/O comments can be
input for each device type. Data
from Excel and other applications
can be copied and pasted via the
clipboard.
Text command
input mode
■ FROM data storage
12
Status display
AFPX-C30/C60
PC
During the first scan, read one block
(2048 words) from the starting address of
DT0 at block number 0.
P13 ICWD DT0, K1, K0
When R0 is turned on, write one block
(2048 words) starting from the address
DT0 at block number 0.
●Wizard function
This software is for importing and
exporting programs created in text
format to and from FPWIN GR.
Programs created on the PLC of
another company can be edited as
text and then be transferred to the
FP Series without difficulty.
A ladder diagram is displayed
as a mnemonic code is entered
from the keyboard.
A Wizard function included in FPWIN GR since versions
2.2 can automatically generate ladder programs by
simply entering and selecting required items in the
dedicated screen. It can be used to assist in positioning,
PID instruction input, and FP-e screen display
instruction input.
●Personal preference settings
It is possible to switch among preference settings for
FPWIN GR, Data Editor and Text Compiler that are set
up for different individuals.
13
Program protection
Programming
Note: Product names and company names in this chart are trademarks or registered trademarks of the respective companies.
Protects your important program by preventing
illegal copies
Protected
Protected
Master memory
■ Program upload is easily prohibited by tool
software FPWIN.
Items possible
during an uploadprohibited condition
●Reading a program from the PLC main unit is virtually impossible.
●In the upload-prohibited condition, program transfers to the master
memory are also prohibited.
●Release of an upload-prohibited condition is possible with a forced
release accompanied by a program deletion.
●Program updates are easily carried out by transferring the program in
the master memory to FP-X even during an upload-prohibited condition.
The transferred program in FP-X is setup with the same upload
prohibition and permission conditions used in the master memory.
Program download from a PC
Data transfer from the master
memory
Change of data monitor/resistor value
Contact monitor
Time chart monitor
Items impossible Program upload to a PC
during an upload- Data transfer to the master memory
prohibited condition
Forced input/output
(Original program is required)
Ladder monitor
(Original program is required)
Rewrite during RUN mode
(Original program is required)
Password protection
■ More secure eight-character password can be used
along with the previous four-character password.
●The combination of upper and lower case alphanumeric characters
produces 218 trillion combinations. In addition, after three consecutive
entry failures, a power reset is required for password release.
Control FPWIN GR for Windows
The ladder programming software for FP series − highly operational software tool for maximizing convenience
in the field.
■ Operational Environment
■ Features
1. Easy field operations not requiring the use of a mouse for data
entry, search, writing, monitoring and timer changes, all carried
out only from the keyboard.
2. Allows standard operations in Windows, such as Copy & Paste,
etc.
3. All FP series PLCs are supported. The software assets produced
by using Ver. 4 or Ver. 3 of NPST-GR are usable.
4. Easy programming with wizard functions.
5. Communication with OPC Server, CommX, GTWIN, PCWAY
simultaneously through the same port.
OS
Windows95 (OSR2 or higher)/98/Me/
NT (Ver. 4.0 or later)/2000/XP
Hard disk capacity
At least 40 MB
CPU
Pentium 100 MHz or higher
Onboard memory
At least 64 MB (depends on OS)
Screen resolution
At least 1024 × 768
Display colors
High color (16-bit or higher)
Applicable PLC
FP-X/FP-e/FP0/FPΣ/FP2/FP2SH
Compatible FP-X
version
Relay output type: Ver.2.50 and after
Transistor output type: Ver.2.70 and after
Tool bar
Adaptability
Access often-used functions
using icons.
Program status display
Data monitoring window
Search window
Relay monitoring window
Allows you to search various data
High versatility and rich functionality provides “peace of mind” and “flexibility”.
Function bar
Program display
Bottons for command input
and confirmation, on-line/offline selection and PLC mode
selection.
■ An expensive USB conversion adapter/cable is not necessary for connecting
a PC to the PLC by using a standard USB port.*
In the case of FP-X
Before
PC
RS232C/422 Previous Model
conversion
adapter
USB
conversion cable
* USB port is equipped with C30 and C60.
Function instruction list
I/O comment edit function
USB cable direct
connection
The conventional RS232C port can also be used.
■ The master memory makes a program transfer easy and a real-time clock is equipped also
●The built-in 1 MB flash-ROM can store a 32-kstep program as well as the
comments and FPWIN Pro source file.
●Program update in a remote location is easy by simply sending master
memory for local installation.
●As the master memory stores the password information, password protection can be
applied for program transmission. Similarly, upload prohibition/permission can be setup.
●The built-in real-time clock enables periodical repeated control and
periodical data logging.
■ No need for program backup − easy maintenance
Master memory
To the field
operation
Program
transfer
FPWIN GR/Pro
FP-X
Program
transfer
●The programs and comments are stored in flash ROM, requiring no backup batteries.
●A backup battery is provided for data and real-time clock (AFPX-BATT)
One battery for C14, two for C30 and three for C60 can be attached. A twoBattery
battery installation can operate for a long time (10 years or more) without
holder
maintenance. (Real-time clock doesn't work without a battery.)
FP-X
Password used ➔ Password locked
Upload prohibited set ➔ Upload prohibited
Upload prohibited not set ➔ Upload permitted
●FP-X can store a program, comments, a total of 55 words of data, and
bit setting values in a flash memory without a battery. All of the data
and bits can be stored by adding optional batteries, but writing into a
flash ROM is possible without a battery by using applied instructions
(F12, P13). Perfectly suited for data storage of the setup values and
recipes modified several times a day.
Flash-ROM
* The limitation in a flash ROM designates the number of rewrites to be 10,000, or the feasible number to be approx 30,000. However,
rewriting every second will generate a memory failure within a few hours.
Writing
Classified by type, function
instructions can be selected from
the displayed list.
(Simple help included.)
Displays information concerning
PLC usage situation and settings,
and detailed information when an
error occurs.
■ Accompanying Tools
Text Compiler
Text command input mode
●Data Editor
This software for the PC is for reading and writing data
stored in the memory of FP Series main unit or on an IC
card. If a large data table is required in a PLC, the data
can be created and edited on a PC and then dowmload
to the PLC.
●Modem connection
Connector
Communication via modem is easy with FP Series units
in isolated locations.
Backup battery
for FP-X
(AFPX-BATT)
F12 ICRD K0, K1, DT0
Reading
Successive I/O comments can be
input for each device type. Data
from Excel and other applications
can be copied and pasted via the
clipboard.
Text command
input mode
■ FROM data storage
12
Status display
AFPX-C30/C60
PC
During the first scan, read one block
(2048 words) from the starting address of
DT0 at block number 0.
P13 ICWD DT0, K1, K0
When R0 is turned on, write one block
(2048 words) starting from the address
DT0 at block number 0.
●Wizard function
This software is for importing and
exporting programs created in text
format to and from FPWIN GR.
Programs created on the PLC of
another company can be edited as
text and then be transferred to the
FP Series without difficulty.
A ladder diagram is displayed
as a mnemonic code is entered
from the keyboard.
A Wizard function included in FPWIN GR since versions
2.2 can automatically generate ladder programs by
simply entering and selecting required items in the
dedicated screen. It can be used to assist in positioning,
PID instruction input, and FP-e screen display
instruction input.
●Personal preference settings
It is possible to switch among preference settings for
FPWIN GR, Data Editor and Text Compiler that are set
up for different individuals.
13
Part Number List
Programming
Note: Product names and company names in this chart are trademarks or registered trademarks of the respective companies.
FP-X Control Unit
Control FPWIN Pro (IEC61131-3 compliant Windows version software)
Product name
Relay output
Compliant with international standard IEC61131-3
Programming software approved by PLC Open
■ Features
3. Keep know-how from getting out
1. Five programming languages can
be used.
Programming can be done using the
language most familiar to the developer
or using the language most suited to the
process to be performed. High-level
(structured text) languages that allow
structuring, such as C, are supported.
4. Conversion function for previously
written programs provided to allow
use of program assets.
5. Uploading of source programs
from PLC possible.
2. Easy to reuse well-proven
programs
Maintainability increased by being able to
load programs and comments from the
PLC.
* This only applies to FP-X, FPΣ and FP2
(with comment memory) and to FP2SH
and FP10SH (with card board).
Efficiency when writing programs has
been greatly increased by being able to
split programming up for each function
and process using structured
programming.
Transistor output
By “black boxing” a part of a program, you
can prevent know-how from leaking out
and improve the program’s maintainability.
6. Programming for all models in the
FP series possible.
Any model can be used.
Easy-to-understand, efficient programs can be created, for example, by
using a ladder program for machine control or ST for communications
control.
■ “Black boxing” of programs
●Multiple passwords for protection of each block
The security level (8 levels) can be input for each block in a program. Only users
of a set security level or higher can make changes.
●Programming in the language you are good at
Person A (designer)
Programming time can be greatly reduced by the easy ability to split and
then integrate programming for each function and process.
Main program
(SFC)
Designer A
(SFC)
Positioning program
(ST)
Designer B
(ST)
Completed
program
Communications
program
(ST)
Person B (floor leader)
Block 1
Block 2
All blocks
Block 1
Block 2
Person C (operator)
100 to 240V AC
100 to 240V AC
24V DC
100 to 240V AC
24V DC
100 to 240V AC
24V DC
100 to 240V AC
24V DC
100 to 240V AC
24V DC
100 to 240V AC
24V DC
100 to 240V AC
Product name
Only block 1
Block 2
Block 1 Low
Block 2
Block 3
Block 4 High
Block 4
Completed
program
FP-X E30R Expansion I/O unit
100 to 240V AC
FP-X E16T Expansion I/O unit
FP-X E16P Expansion I/O unit
FP-X E30TD Expansion I/O unit
FP-X E30T Expansion I/O unit
24V DC
100 to 240V AC
FP-X E30P Expansion I/O unit
● Register time-proven programs by block in the library.
● By using variable identifiers (names), there is no need to be
concerned with addresses for each machine when reusing
programs.
New program
Positioning program
■ Operational Environment
OS
Windows95 (OSR2 or higher)/98/Me/NT (Ver. 4.0 or later)/2000/XP
Hard disk capacity
At least 100 MB
CPU
Pentium 100 MHz or higher
Onboard memory
At least 64 MB (depends on OS)
Screen resolution
At least 1024 × 768
Display colors
High Color (16-bit) or higher
Applicable PLC
FP-X/FP-e/FP0/FPΣ/FP1/FP-M/FP2/FP2SH/FP3/FP10SH
Compatible FP-X
version
Relay output type: Ver.5.1 and after
Transistor output type: Ver.5.3 and after (Available soon)
Communications program
Malfunction handling
program
Position
Operation
Function
Modem
Connection
Function
Communications program
Malfunction handling
program
Main program
Initialliton
Setting
Process
14
16-point of 24 V DC, 14-point output of 0.5 A transistor (PNP)
Program capacity 32 ksteps, 2-point potentiometer, USB port
16-point of 24 V DC, 14-point output of 0.5 A transistor (PNP)
Program capacity 32 ksteps, 2-point potentiometer, USB port
32-point of 24 V DC, 28-point output of 0.5 A transistor (NPN)
Program capacity 32 ksteps, 4-point potentiometer, USB port
32-point of 24 V DC, 28-point output of 0.5 A transistor (NPN)
Program capacity 32 ksteps, 4-point potentiometer, USB port
32-point of 24 V DC, 28-point output of 0.5 A transistor (PNP)
Program capacity 32 ksteps, 4-point potentiometer, USB port
32-point of 24 V DC, 28-point output of 0.5 A transistor (PNP)
Program capacity 32 ksteps, 4-point potentiometer, USB port
AFPX-C30R
AFPX-C60R
AFPX-C14TD
AFPX-C14T
AFPX-C14PD
AFPX-C14P
AFPX-C30TD
AFPX-C30T
AFPX-C30PD
AFPX-C30P
AFPX-C60TD
AFPX-C60T
AFPX-C60PD
AFPX-C60P
Specifications
8-point input of 24 V DC, 8-point relay output of 2 A
Remarks; Two or more E16R can't be connected serially because it can't supply the power to other units. With an 8cm extension cable
16-point input of 24 V DC, 14-point relay output of 2 A
Remarks; Possible to connect up to 8 units including E16R, EFP0. With an 8cm extension cable
16-point input of 24 V DC, 14-point transistor (NPN) output of 0.5 A
Remarks; Possible to connect up to 8 units including E16, EFP0. With an 8cm extension cable
16-point input of 24 V DC, 14-point transistor (NPN) output of 0.5 A
Remarks; Possible to connect up to 8 units including E16, EFP0. With an 8cm extension cable
Part number
AFPX-E16R
AFPX-E30R
AFPX-E16T
AFPX-E16P
AFPX-E30TD
AFPX-E30T
24V DC
AFPX-E30PD
100 to 240V AC
16-point input of 24 V DC, 14-point transistor (PNP) output of 0.5 A
Remarks; Possible to connect up to 8 units including E16, EFP0. With an 8cm extension cable
AFPX-E30P
Up to 3 FP0 expansion units can be connected via an adapter.
With an 8cm extension cable and power cable
AFPX-EFP0
24V DC
FP-X Add-on Cassette
■ Reuse of programs is easy.
Positioning program
8-point of 24 V DC, 6-point output of 0.5 A transistor (PNP)
Program capacity 16 ksteps, 2-point potentiometer
16-point of 24 V DC, 14-point output of 0.5 A transistor (NPN)
Program capacity 32 ksteps, 2-point potentiometer, USB port
16-point of 24 V DC, 14-point output of 0.5 A transistor (NPN)
Program capacity 32 ksteps, 4-point potentiometer, USB port
Part number
AFPX-C14R
16-point input of 24 V DC, 14-point transistor (PNP) output of 0.5 A
Remarks; Possible to connect up to 8 units including E16, EFP0. With an 8cm extension cable
Expansion FP0 Adapter
Parts library
8-point of 24 V DC, 6-point output of 0.5 A transistor (NPN)
Program capacity 16 ksteps, 2-point potentiometer
8-point of 24 V DC, 6-point output of 0.5 A transistor (NPN)
Program capacity 16 ksteps, 2-point potentiometer
8-point of 24 V DC, 6-point output of 0.5 A transistor (PNP)
Program capacity 16 ksteps, 2-point potentiometer
8-point input of 24 V DC, 8-point transistor (NPN) output of 0.5 A
Remarks; Two or more E16T cannot be connected serially because it cannot supply the power to other units. With an 8cm extension cable
8-point input of 24 V DC, 8-point transistor (PNP) output of 0.5 A
Remarks; Two or more E16T cannot be connected serially because it cannot supply the power to other units. With an 8cm extension cable
FP-X E30PD Expansion I/O unit
Designer D
(ladder)
Specifications
8-point input of 24 V DC, 6-point output of 2 A relay
Program capacity 16 ksteps, 2-point potentiometer
16-point input of 24 V DC, 14-point output of 2 A relay
Program capacity 32 ksteps, 2-point potentiometer, USB port
32-point input of 24 V DC, 28-point output of 2 A relay
Program capacity 32 ksteps, 4-point potentiometer, USB port
Power supply
FP-X E16R Expansion I/O unit
Programming security level
Designer C
(ST)
Malfunction handling
program
(ladder)
Power supply
100 to 240V AC
FP-X Expansion Unit
Relay output
●Programming in the language most suited to the process
FP-X C14PD
Control unit
FP-X C14P
Control unit
FP-X C30TD
Control unit
FP-X C30T
Control unit
FP-X C30PD
Control unit
FP-X C30P
Control unit
FP-X C60TD
Control unit
FP-X C60T
Control unit
FP-X C60PD
Control unit
FP-X C60P
Control unit
Transistor output
■ Programming in the most suitable language
FP-X C14R
Control unit
FP-X C30R
Control unit
FP-X C60R
Control unit
FP-X C14TD
Control unit
FP-X C14T
Control unit
Product name
Specifications
Part number
FP-X COM1 Communication cassette
FP-X COM2 Communication cassette
FP-X COM3 Communication cassette
FP-X COM4 Communication cassette
FP-X COM5 Communication cassette
FP-X Input cassette
RS232C 1 ch. RS, CS control signal equipped (non-insulated)
RS232C 2 ch. (non-insulated)
RS485/422 selectable 1ch (insulated)
RS485 1 ch. (insulated) + RS232C 1 ch. (non-insulated)
Ethernet 1 ch.(10BASE-T, 100BASE-TX) + RS232C 1 ch. (non-insulated)
8 point input of 24 V DC
8 point output of NPN 0.3 A
6 point output of PNP 0.5 A
2 point 12-bit non-insulated 0 to 10 V DC/0 to 20 mA
High-speed counter: single-phase 2 ch., each 80 kHz or two-phase 1 ch., 30 kHz.
Pulse output: one axis 100 kHz/ch. (Use restriction is applied for a two-unit installation)
Master memory: Capable of storing all program steps and comments simultaneously. Storage of FPWIN Pro source files.
Real-time clock: Year, month, day, hour, minute, second, day of week (optional battery required)
AFPX-COM1
AFPX-COM2
AFPX-COM3
AFPX-COM4
AFPX-COM5
AFPX-IN8
AFPX-TR8
AFPX-TR6P
AFPX-AD2
FP-X Output cassette
FP-X Analog input cassette
FP-X Pulse I/O cassette
(for relay output type control unit only)
FP-X Master memory
with a real-time clock
AFPX-PLS
AFPX-MRTC
FP-X Options and Service Parts
Product name
FP-X Backup battery
FP-X Expansion cable (8 cm)
FP-X Expansion cable (30 cm)
FP-X Expansion cable (80 cm)
FP-X Terminal block
Specifications
Part number
Battery for backing up the operation memory and real-time clock
Expansion unit connection cable, 8 cm
Expansion unit connection cable, 30 cm
Expansion unit connection cable, 80 cm
Terminal block for C30, C60 and E30, 21 pins, cover with no marking, five units included
AFPX-BATT
AFPX-EC08
AFPX-EC30
AFPX-EC80
AFPX-TAN1
15
Part Number List
Programming
Note: Product names and company names in this chart are trademarks or registered trademarks of the respective companies.
FP-X Control Unit
Control FPWIN Pro (IEC61131-3 compliant Windows version software)
Product name
Relay output
Compliant with international standard IEC61131-3
Programming software approved by PLC Open
■ Features
3. Keep know-how from getting out
1. Five programming languages can
be used.
Programming can be done using the
language most familiar to the developer
or using the language most suited to the
process to be performed. High-level
(structured text) languages that allow
structuring, such as C, are supported.
4. Conversion function for previously
written programs provided to allow
use of program assets.
5. Uploading of source programs
from PLC possible.
2. Easy to reuse well-proven
programs
Maintainability increased by being able to
load programs and comments from the
PLC.
* This only applies to FP-X, FPΣ and FP2
(with comment memory) and to FP2SH
and FP10SH (with card board).
Efficiency when writing programs has
been greatly increased by being able to
split programming up for each function
and process using structured
programming.
Transistor output
By “black boxing” a part of a program, you
can prevent know-how from leaking out
and improve the program’s maintainability.
6. Programming for all models in the
FP series possible.
Any model can be used.
Easy-to-understand, efficient programs can be created, for example, by
using a ladder program for machine control or ST for communications
control.
■ “Black boxing” of programs
●Multiple passwords for protection of each block
The security level (8 levels) can be input for each block in a program. Only users
of a set security level or higher can make changes.
●Programming in the language you are good at
Person A (designer)
Programming time can be greatly reduced by the easy ability to split and
then integrate programming for each function and process.
Main program
(SFC)
Designer A
(SFC)
Positioning program
(ST)
Designer B
(ST)
Completed
program
Communications
program
(ST)
Person B (floor leader)
Block 1
Block 2
All blocks
Block 1
Block 2
Person C (operator)
100 to 240V AC
100 to 240V AC
24V DC
100 to 240V AC
24V DC
100 to 240V AC
24V DC
100 to 240V AC
24V DC
100 to 240V AC
24V DC
100 to 240V AC
24V DC
100 to 240V AC
Product name
Only block 1
Block 2
Block 1 Low
Block 2
Block 3
Block 4 High
Block 4
Completed
program
FP-X E30R Expansion I/O unit
100 to 240V AC
FP-X E16T Expansion I/O unit
FP-X E16P Expansion I/O unit
FP-X E30TD Expansion I/O unit
FP-X E30T Expansion I/O unit
24V DC
100 to 240V AC
FP-X E30P Expansion I/O unit
● Register time-proven programs by block in the library.
● By using variable identifiers (names), there is no need to be
concerned with addresses for each machine when reusing
programs.
New program
Positioning program
■ Operational Environment
OS
Windows95 (OSR2 or higher)/98/Me/NT (Ver. 4.0 or later)/2000/XP
Hard disk capacity
At least 100 MB
CPU
Pentium 100 MHz or higher
Onboard memory
At least 64 MB (depends on OS)
Screen resolution
At least 1024 × 768
Display colors
High Color (16-bit) or higher
Applicable PLC
FP-X/FP-e/FP0/FPΣ/FP1/FP-M/FP2/FP2SH/FP3/FP10SH
Compatible FP-X
version
Relay output type: Ver.5.1 and after
Transistor output type: Ver.5.3 and after (Available soon)
Communications program
Malfunction handling
program
Position
Operation
Function
Modem
Connection
Function
Communications program
Malfunction handling
program
Main program
Initialliton
Setting
Process
14
16-point of 24 V DC, 14-point output of 0.5 A transistor (PNP)
Program capacity 32 ksteps, 2-point potentiometer, USB port
16-point of 24 V DC, 14-point output of 0.5 A transistor (PNP)
Program capacity 32 ksteps, 2-point potentiometer, USB port
32-point of 24 V DC, 28-point output of 0.5 A transistor (NPN)
Program capacity 32 ksteps, 4-point potentiometer, USB port
32-point of 24 V DC, 28-point output of 0.5 A transistor (NPN)
Program capacity 32 ksteps, 4-point potentiometer, USB port
32-point of 24 V DC, 28-point output of 0.5 A transistor (PNP)
Program capacity 32 ksteps, 4-point potentiometer, USB port
32-point of 24 V DC, 28-point output of 0.5 A transistor (PNP)
Program capacity 32 ksteps, 4-point potentiometer, USB port
AFPX-C30R
AFPX-C60R
AFPX-C14TD
AFPX-C14T
AFPX-C14PD
AFPX-C14P
AFPX-C30TD
AFPX-C30T
AFPX-C30PD
AFPX-C30P
AFPX-C60TD
AFPX-C60T
AFPX-C60PD
AFPX-C60P
Specifications
8-point input of 24 V DC, 8-point relay output of 2 A
Remarks; Two or more E16R can't be connected serially because it can't supply the power to other units. With an 8cm extension cable
16-point input of 24 V DC, 14-point relay output of 2 A
Remarks; Possible to connect up to 8 units including E16R, EFP0. With an 8cm extension cable
16-point input of 24 V DC, 14-point transistor (NPN) output of 0.5 A
Remarks; Possible to connect up to 8 units including E16, EFP0. With an 8cm extension cable
16-point input of 24 V DC, 14-point transistor (NPN) output of 0.5 A
Remarks; Possible to connect up to 8 units including E16, EFP0. With an 8cm extension cable
Part number
AFPX-E16R
AFPX-E30R
AFPX-E16T
AFPX-E16P
AFPX-E30TD
AFPX-E30T
24V DC
AFPX-E30PD
100 to 240V AC
16-point input of 24 V DC, 14-point transistor (PNP) output of 0.5 A
Remarks; Possible to connect up to 8 units including E16, EFP0. With an 8cm extension cable
AFPX-E30P
Up to 3 FP0 expansion units can be connected via an adapter.
With an 8cm extension cable and power cable
AFPX-EFP0
24V DC
FP-X Add-on Cassette
■ Reuse of programs is easy.
Positioning program
8-point of 24 V DC, 6-point output of 0.5 A transistor (PNP)
Program capacity 16 ksteps, 2-point potentiometer
16-point of 24 V DC, 14-point output of 0.5 A transistor (NPN)
Program capacity 32 ksteps, 2-point potentiometer, USB port
16-point of 24 V DC, 14-point output of 0.5 A transistor (NPN)
Program capacity 32 ksteps, 4-point potentiometer, USB port
Part number
AFPX-C14R
16-point input of 24 V DC, 14-point transistor (PNP) output of 0.5 A
Remarks; Possible to connect up to 8 units including E16, EFP0. With an 8cm extension cable
Expansion FP0 Adapter
Parts library
8-point of 24 V DC, 6-point output of 0.5 A transistor (NPN)
Program capacity 16 ksteps, 2-point potentiometer
8-point of 24 V DC, 6-point output of 0.5 A transistor (NPN)
Program capacity 16 ksteps, 2-point potentiometer
8-point of 24 V DC, 6-point output of 0.5 A transistor (PNP)
Program capacity 16 ksteps, 2-point potentiometer
8-point input of 24 V DC, 8-point transistor (NPN) output of 0.5 A
Remarks; Two or more E16T cannot be connected serially because it cannot supply the power to other units. With an 8cm extension cable
8-point input of 24 V DC, 8-point transistor (PNP) output of 0.5 A
Remarks; Two or more E16T cannot be connected serially because it cannot supply the power to other units. With an 8cm extension cable
FP-X E30PD Expansion I/O unit
Designer D
(ladder)
Specifications
8-point input of 24 V DC, 6-point output of 2 A relay
Program capacity 16 ksteps, 2-point potentiometer
16-point input of 24 V DC, 14-point output of 2 A relay
Program capacity 32 ksteps, 2-point potentiometer, USB port
32-point input of 24 V DC, 28-point output of 2 A relay
Program capacity 32 ksteps, 4-point potentiometer, USB port
Power supply
FP-X E16R Expansion I/O unit
Programming security level
Designer C
(ST)
Malfunction handling
program
(ladder)
Power supply
100 to 240V AC
FP-X Expansion Unit
Relay output
●Programming in the language most suited to the process
FP-X C14PD
Control unit
FP-X C14P
Control unit
FP-X C30TD
Control unit
FP-X C30T
Control unit
FP-X C30PD
Control unit
FP-X C30P
Control unit
FP-X C60TD
Control unit
FP-X C60T
Control unit
FP-X C60PD
Control unit
FP-X C60P
Control unit
Transistor output
■ Programming in the most suitable language
FP-X C14R
Control unit
FP-X C30R
Control unit
FP-X C60R
Control unit
FP-X C14TD
Control unit
FP-X C14T
Control unit
Product name
Specifications
Part number
FP-X COM1 Communication cassette
FP-X COM2 Communication cassette
FP-X COM3 Communication cassette
FP-X COM4 Communication cassette
FP-X COM5 Communication cassette
FP-X Input cassette
RS232C 1 ch. RS, CS control signal equipped (non-insulated)
RS232C 2 ch. (non-insulated)
RS485/422 selectable 1ch (insulated)
RS485 1 ch. (insulated) + RS232C 1 ch. (non-insulated)
Ethernet 1 ch.(10BASE-T, 100BASE-TX) + RS232C 1 ch. (non-insulated)
8 point input of 24 V DC
8 point output of NPN 0.3 A
6 point output of PNP 0.5 A
2 point 12-bit non-insulated 0 to 10 V DC/0 to 20 mA
High-speed counter: single-phase 2 ch., each 80 kHz or two-phase 1 ch., 30 kHz.
Pulse output: one axis 100 kHz/ch. (Use restriction is applied for a two-unit installation)
Master memory: Capable of storing all program steps and comments simultaneously. Storage of FPWIN Pro source files.
Real-time clock: Year, month, day, hour, minute, second, day of week (optional battery required)
AFPX-COM1
AFPX-COM2
AFPX-COM3
AFPX-COM4
AFPX-COM5
AFPX-IN8
AFPX-TR8
AFPX-TR6P
AFPX-AD2
FP-X Output cassette
FP-X Analog input cassette
FP-X Pulse I/O cassette
(for relay output type control unit only)
FP-X Master memory
with a real-time clock
AFPX-PLS
AFPX-MRTC
FP-X Options and Service Parts
Product name
FP-X Backup battery
FP-X Expansion cable (8 cm)
FP-X Expansion cable (30 cm)
FP-X Expansion cable (80 cm)
FP-X Terminal block
Specifications
Part number
Battery for backing up the operation memory and real-time clock
Expansion unit connection cable, 8 cm
Expansion unit connection cable, 30 cm
Expansion unit connection cable, 80 cm
Terminal block for C30, C60 and E30, 21 pins, cover with no marking, five units included
AFPX-BATT
AFPX-EC08
AFPX-EC30
AFPX-EC80
AFPX-TAN1
15
Related Products
Related Products List
Part Number List
FP Memory Loader
FP0 Expansion Units
Product name
Specifications
Number of I/O points
8
8
Input: 8
Input: 4
Output: 4
8
FP0 E32 Expansion Unit
Input
Output
Connection type
24 V DC Sink/Source (±common)
−
MIL connector
Terminal block
Molex connecter
Terminal block
24 V DC Sink/Source (±common)
Relay output: 2 A
Output: 8
24 V DC
−
8
Output: 8
−
−
16
Input: 16
16
Input: 8
Output: 8
Input: 8
Output: 8
16
32
16
FP0 E16 Expansion Unit
Power supply
voltage
−
24 V DC
FP0 E8 Expansion Unit
FP Web-Server Unit
Product name
−
24 V DC Sink/Source (±common)
Relay output: 2 A
Transistor output:
NPN 0.1 A
−
24 V DC
24 V DC Sink/Source (±common)
Relay output: 2 A
Product number
Part number
FP0-E8X
FP0-E8RS
FP0-E8RM
FP0-E8YRS
AFP03003
AFP03023
AFP03013
AFP03020
FP0-E8YT
AFP03040
MIL connector
Part number
FP Web-Server unit
Data hold type
AFP8671
FP Web Configurator Tool
PCWAY Ver. 2.7 (Operation Data Managing Software)
Product name
AFW10011
PCWAY USB port version
AFW10031
Product name
PCWAY Version upgrade
AFW10401
Key unit IBM printer port version
AFW1031*
Key unit USB port version
AFW1033
* Charged version upgrade for Ver. 2.0 to 2.6.
Control CommX Ver. 1.3 (OCX for Communication)
FP0-E16RS
FP0-E16RM
AFP03323
AFP03313
Product name
Control CommX IBM printer port
AFW20011
Control CommX USB port
AFW20031
MIL connector
FP0-E16T
AFP03343
Output: 16
−
−
MIL connector
FP0-E16YT
AFP03340
Input: 16
Output: 16
−
24 V DC Sink/Source (±common)
Transistor output:
NPN 0.1 A
Transistor output:
NPN 0.1 A
MIL connector
FP0-E32T
AFP03543
Notes: 1) The relay output type expansion units come with a power cable (part number AFP0581). (The transistor output type needs no power cable.)
2) The terminal block type relay output units have 2 terminal blocks (9 pins) made by Phoenix. Use a 2.5 mm wide screwdriver.
Preferably use the specific terminal block screwdriver (part number AFP0806, Phoenix type code SZS 0. 4 × 2.5 mm) or equivalent.
3) The connector-type relay output units have 2 connectors made by Nihon Molex (Molex type code 51067-0900, 9 pins).
Use the specific Molex connector press-fit tool (part number AFP0805, Nihon Molex type code 57189-5000) or equivalent.
4) The transistor output units have a press-fit socket for wire-pressed terminal cable and contacts. Use the press-fit tool (part number AXY52000) for wire-pressed terminal cable.
Key Unit
PCWAY IBM printer port version
AFP03303
Transistor output:
NPN 0.1 A
AFP0610
AFPS30510
Economical type is available for secondary key.
The key unit is available for PCWAY and Control CommX.
Part number
FP0-E16X
24 V DC Sink/Source (±common)
Part number
AFP8670
MIL connector
Terminal block
Molex connecter
−
Product name
Data non-hold type
Part number
*The discontinuation of AFW1031 production is scheduled for August 2007.
Part number
Specifications
FP0 Intelligent Units
Product name
FP0 Thermocouple unit
Specifications
K, J, T, R thermocouple, Resolution: 0.1 °C
K, J, T, R thermocouple, Resolution: 0.1 °C
<Input specifications>
Number of channels:
Input range:
FP0 Analog I/O unit
FP0 A/D Converter Unit
<Output specifications>
Number of channels:
Output range:
<Input specifications>
Number of channels:
Input range:
<Output specifications>
Number of channels:
Output range:
FP0 D/A Converter Unit
Product number
FP0-TC4
FP0-TC8
2 channels
0 to 5 V, –10 to +10 V (Resolution: 1/4000)
0 to 20 mA (Resolution: 1/4000)
1 channel
–10 to +10 V (Resolution: 1/4000)
0 to 20 mA (Resolution: 1/4000)
8 channels
0 to 5, –10 to +10 V, –100 to 100 mV (Resolution: 1/4000)
0 to 20 mA (Resolution: 1/4000)
4 channels
–10 to +10 V (Resolution: 1/4000)
4 to 20 mA (Resolution: 1/4000)
Part number
AFP0420
AFP0421
AFP0480
FP0-A80
AFP0401
FP0-A04V
AFP04121
FP0-A04I
AFP04123
Power supply
Product number
voltage
FP0 CC-Link Slave unit
Specifications
This unit is for making the FP0 function as a slave station of the CC-Link.
Only one unit can be connected to the furthest right edge of the FP0 expansion bus.
Allowed momentary power off time
Ambient temperature
Storage temperature
Ambient humidity
Storage humidity
FP0 I/O Link unit
This is a link unit designed to make the FP0 function as a station to MEWNET-F (remote I/O system).
Part number
Breakdown voltage
Note: Accuracy will change if an FP0 thermocouple unit is used at the same time. For details, please refer to the FP0 catalog
or to the CC-Link Unit manual.
24 V DC
FP0-CCLS
AFP07943
24 V DC
FP0-IOL
AFP0732
Control FPWIN GR for Windows
Product name
Insulation resistance
Type
Part number
English: Full type
English: Small type
English: Ver. up type
Chinese
Chinese: Ver. up type
Korean
CD-ROM for Windows
CD-ROM for Windows
CD-ROM for Windows
CD-ROM for Windows
CD-ROM for Windows
CD-ROM for Windows
*The production of FP1, FP-M, FP3/FP10SH has been discontinued.
FPWIN GR
for Windows
FP-X
FPΣ
FP0
.
FP-e
A
A
A
A
A
A
A
A
A
AFPS10520
AFPS11520
AFPS10520R
AFPS10820
AFPS10820R
AFPS10920
Applicable PLC
FP0
FP1*
FP2
10k
A
A
A
A
A
N/A
A
A
A
FP2SH FP-M*
FP3*
.
FP10SH
A
N/A
A
A
A
N/A
A
A
A
A: Available, N/A: Not available
FPWIN Pro
for Windows
Type
English: Full type
English: Small type
Part number
CD-ROM for Windows
CD-ROM for Windows
AFPS50550
AFPS51550
FP-X
FPΣ
FP0
.
FP-e
A
A
A
A
A
A
Applicable PLC
FP0
FP1*
FP2
10k
A
A
A
A
A
N/A
A
N/A
A
A
Programmable Display GT series
Description
GT01: Main Unit
RS232C type
5 V DC
RS422/RS485 type
STN monochrome LCD
RS232C type
24 V DC
RS422/RS485 type
GT11: Main Unit
RS232C type
24 V DC
RS422/RS485 type
GT21C: Main Unit
RS232C type
STN color LCD
24 V DC
RS422/RS485 type
16
FP3*
.
FP10SH
A
N/A
Control unit
Expansion I/O unit
Black
Ash gry
Black
Ash gry
Black
Ash gry
Black
Ash gry
Black
Ash gry
Black
Ash gry
Black
Silver
Black
Silver
Part number
Current consumption
Weight
AFPX-C14❍❍
26 W or less *2
Approx. 280 g or less
AFPX-C30❍❍
52 W or less *2
Approx. 490 g or less
AFPX-C60❍❍
64 W or less *2
Approx. 780 g or less
AFPX-E16❍❍
8 W or less *2
Approx. 195 g or less
AFPX-E30❍❍
42 W or less *2
Approx. 430 g or less
AFPX-EFP0
0.24 W or less *3
Approx. 65 g
Part number
AFPX-COM1
2 W or less *2
Approx. 20 g
AIGT0030B1
AIGT0030H1
AIGT0032B1
AIGT0032H1
AIGT0030B
AIGT0030H
AIGT0032B
AIGT0032H
AIGT2030B
AIGT2030H
AIGT2032B
AIGT2032H
AIGT2230B
AIGT2230H
AIGT2232B
AIGT2232H
AFPX-COM2
2 W or less *2
Approx. 20 g
AFPX-COM3
2 W or less *2
Approx. 20 g
AFPX-COM4
2 W or less *2
Approx. 20 g
AFPX-COM5
2 W or less *2
Approx. 20 g
AFPX-AD2
2 W or less *2
Approx. 25 g
AFPX-IN8
1 W or less *2
Approx. 25 g
AFPX-TR8
1 W or less *2
Approx. 25 g
AFPX-TR6P
1 W or less *2
Approx. 25 g
AFPX-PLS
2 W or less *2
Approx. 25 g
AFPX-MRTC
2 W or less *2
Approx. 20 g
Expansion FP0 adapter
Product name
1500 V [P-P] pulse width 50 ns, 1 µs (AC power), 500 V [P-P] pulse width 50 ns, 1 µs (DC power) (per noise simulator method) (power terminals)
No corrosive gas and no excessive dust
Conforming to EN61131-2
2
II
*1 Cutoff current 5 mA
Product name
FP2SH FP-M*
A: Available, N/A: Not available
*The production of FP1, FP-M, FP3/FP10SH has been discontinued.
STN monochrome LCD
Vibration resistance
Shock resistance
Noise immunity
Operating condition
EC Directive Compliance Standard
Level of contamination
Over-voltage category
100 to 240 V AC (AC power), 24 V DC (DC power)
85 to 264 V AC (AC power), 20.4 to 28.8 V DC (DC power)
40 A or less (C14), 45 A or less (C30, C60) at 25°C (AC power)
12 A or less at 25°C (DC power)
10 ms or more
0 to +55°C
-40 to +70°C
10 to 95% RH (at 25 °C, non-condensing)
10 to 95% RH (at 25 °C, non-condensing)
Combined input/output terminals - Combined power and ground terminals,
2300 V AC 1 minute (AC power), 500 V AC*1 1 minute (DC power)
Input terminals - Relay output terminals, 2300 V AC*1 1 minute
Input terminals - Transistor output terminals, 500 V AC*1 1 minute
Power terminals - Ground terminals, 1500 V AC*1 1 minute (AC power), 500 V AC*1 1 minute (DC power)
Combined input/output terminals - Combined power and ground terminals, 100 MΩ or higher (500 V DC using an insulation resistance meter)
Input terminals - Output terminals, 100 MΩ or higher (500 V DC using an insulation resistance meter)
Power terminals - Ground terminals, 100 MΩ or higher (500 V DC using an insulation resistance meter)
5 to 9 Hz, single amplitude 3.5 mm/9 to 150 Hz, constant acceleration 9.8 m/s2, 1 sweep/min, 10 sweeps in each XYZ direction
147 m/s2
2. Power Consumption, Weight
Control FPWIN Pro (IEC61131-3 compliant Windows version software)
Product name
Description
Item
Rated voltage
Operating voltage range
Rush current
FP0-A21
FP0 Link Units
Product name
1. General Specifications
FP-X communication cassette
FP-X analog input cassette
FP-X input cassette
FP-X output cassette
FP-X pulse I/O cassette
FP-X master memory cassette
*2 Power consumption by the AC power supply connected to the control unit
*4 Please refer to FP0 users manual for FP0 expansion units.
Please refer to the user manual and specifications for further details.
*3 Power consumption by the DC power supply connected to the expansion FP0 adapter
17
Related Products
Related Products List
Part Number List
FP Memory Loader
FP0 Expansion Units
Product name
Specifications
Number of I/O points
8
8
Input: 8
Input: 4
Output: 4
8
FP0 E32 Expansion Unit
Input
Output
Connection type
24 V DC Sink/Source (±common)
−
MIL connector
Terminal block
Molex connecter
Terminal block
24 V DC Sink/Source (±common)
Relay output: 2 A
Output: 8
24 V DC
−
8
Output: 8
−
−
16
Input: 16
16
Input: 8
Output: 8
Input: 8
Output: 8
16
32
16
FP0 E16 Expansion Unit
Power supply
voltage
−
24 V DC
FP0 E8 Expansion Unit
FP Web-Server Unit
Product name
−
24 V DC Sink/Source (±common)
Relay output: 2 A
Transistor output:
NPN 0.1 A
−
24 V DC
24 V DC Sink/Source (±common)
Relay output: 2 A
Product number
Part number
FP0-E8X
FP0-E8RS
FP0-E8RM
FP0-E8YRS
AFP03003
AFP03023
AFP03013
AFP03020
FP0-E8YT
AFP03040
MIL connector
Part number
FP Web-Server unit
Data hold type
AFP8671
FP Web Configurator Tool
PCWAY Ver. 2.7 (Operation Data Managing Software)
Product name
AFW10011
PCWAY USB port version
AFW10031
Product name
PCWAY Version upgrade
AFW10401
Key unit IBM printer port version
AFW1031*
Key unit USB port version
AFW1033
* Charged version upgrade for Ver. 2.0 to 2.6.
Control CommX Ver. 1.3 (OCX for Communication)
FP0-E16RS
FP0-E16RM
AFP03323
AFP03313
Product name
Control CommX IBM printer port
AFW20011
Control CommX USB port
AFW20031
MIL connector
FP0-E16T
AFP03343
Output: 16
−
−
MIL connector
FP0-E16YT
AFP03340
Input: 16
Output: 16
−
24 V DC Sink/Source (±common)
Transistor output:
NPN 0.1 A
Transistor output:
NPN 0.1 A
MIL connector
FP0-E32T
AFP03543
Notes: 1) The relay output type expansion units come with a power cable (part number AFP0581). (The transistor output type needs no power cable.)
2) The terminal block type relay output units have 2 terminal blocks (9 pins) made by Phoenix. Use a 2.5 mm wide screwdriver.
Preferably use the specific terminal block screwdriver (part number AFP0806, Phoenix type code SZS 0. 4 × 2.5 mm) or equivalent.
3) The connector-type relay output units have 2 connectors made by Nihon Molex (Molex type code 51067-0900, 9 pins).
Use the specific Molex connector press-fit tool (part number AFP0805, Nihon Molex type code 57189-5000) or equivalent.
4) The transistor output units have a press-fit socket for wire-pressed terminal cable and contacts. Use the press-fit tool (part number AXY52000) for wire-pressed terminal cable.
Key Unit
PCWAY IBM printer port version
AFP03303
Transistor output:
NPN 0.1 A
AFP0610
AFPS30510
Economical type is available for secondary key.
The key unit is available for PCWAY and Control CommX.
Part number
FP0-E16X
24 V DC Sink/Source (±common)
Part number
AFP8670
MIL connector
Terminal block
Molex connecter
−
Product name
Data non-hold type
Part number
*The discontinuation of AFW1031 production is scheduled for August 2007.
Part number
Specifications
FP0 Intelligent Units
Product name
FP0 Thermocouple unit
Specifications
K, J, T, R thermocouple, Resolution: 0.1 °C
K, J, T, R thermocouple, Resolution: 0.1 °C
<Input specifications>
Number of channels:
Input range:
FP0 Analog I/O unit
FP0 A/D Converter Unit
<Output specifications>
Number of channels:
Output range:
<Input specifications>
Number of channels:
Input range:
<Output specifications>
Number of channels:
Output range:
FP0 D/A Converter Unit
Product number
FP0-TC4
FP0-TC8
2 channels
0 to 5 V, –10 to +10 V (Resolution: 1/4000)
0 to 20 mA (Resolution: 1/4000)
1 channel
–10 to +10 V (Resolution: 1/4000)
0 to 20 mA (Resolution: 1/4000)
8 channels
0 to 5, –10 to +10 V, –100 to 100 mV (Resolution: 1/4000)
0 to 20 mA (Resolution: 1/4000)
4 channels
–10 to +10 V (Resolution: 1/4000)
4 to 20 mA (Resolution: 1/4000)
Part number
AFP0420
AFP0421
AFP0480
FP0-A80
AFP0401
FP0-A04V
AFP04121
FP0-A04I
AFP04123
Power supply
Product number
voltage
FP0 CC-Link Slave unit
Specifications
This unit is for making the FP0 function as a slave station of the CC-Link.
Only one unit can be connected to the furthest right edge of the FP0 expansion bus.
Allowed momentary power off time
Ambient temperature
Storage temperature
Ambient humidity
Storage humidity
FP0 I/O Link unit
This is a link unit designed to make the FP0 function as a station to MEWNET-F (remote I/O system).
Part number
Breakdown voltage
Note: Accuracy will change if an FP0 thermocouple unit is used at the same time. For details, please refer to the FP0 catalog
or to the CC-Link Unit manual.
24 V DC
FP0-CCLS
AFP07943
24 V DC
FP0-IOL
AFP0732
Control FPWIN GR for Windows
Product name
Insulation resistance
Type
Part number
English: Full type
English: Small type
English: Ver. up type
Chinese
Chinese: Ver. up type
Korean
CD-ROM for Windows
CD-ROM for Windows
CD-ROM for Windows
CD-ROM for Windows
CD-ROM for Windows
CD-ROM for Windows
*The production of FP1, FP-M, FP3/FP10SH has been discontinued.
FPWIN GR
for Windows
FP-X
FPΣ
FP0
.
FP-e
A
A
A
A
A
A
A
A
A
AFPS10520
AFPS11520
AFPS10520R
AFPS10820
AFPS10820R
AFPS10920
Applicable PLC
FP0
FP1*
FP2
10k
A
A
A
A
A
N/A
A
A
A
FP2SH FP-M*
FP3*
.
FP10SH
A
N/A
A
A
A
N/A
A
A
A
A: Available, N/A: Not available
FPWIN Pro
for Windows
Type
English: Full type
English: Small type
Part number
CD-ROM for Windows
CD-ROM for Windows
AFPS50550
AFPS51550
FP-X
FPΣ
FP0
.
FP-e
A
A
A
A
A
A
Applicable PLC
FP0
FP1*
FP2
10k
A
A
A
A
A
N/A
A
N/A
A
A
Programmable Display GT series
Description
GT01: Main Unit
RS232C type
5 V DC
RS422/RS485 type
STN monochrome LCD
RS232C type
24 V DC
RS422/RS485 type
GT11: Main Unit
RS232C type
24 V DC
RS422/RS485 type
GT21C: Main Unit
RS232C type
STN color LCD
24 V DC
RS422/RS485 type
16
FP3*
.
FP10SH
A
N/A
Control unit
Expansion I/O unit
Black
Ash gry
Black
Ash gry
Black
Ash gry
Black
Ash gry
Black
Ash gry
Black
Ash gry
Black
Silver
Black
Silver
Part number
Current consumption
Weight
AFPX-C14❍❍
26 W or less *2
Approx. 280 g or less
AFPX-C30❍❍
52 W or less *2
Approx. 490 g or less
AFPX-C60❍❍
64 W or less *2
Approx. 780 g or less
AFPX-E16❍❍
8 W or less *2
Approx. 195 g or less
AFPX-E30❍❍
42 W or less *2
Approx. 430 g or less
AFPX-EFP0
0.24 W or less *3
Approx. 65 g
Part number
AFPX-COM1
2 W or less *2
Approx. 20 g
AIGT0030B1
AIGT0030H1
AIGT0032B1
AIGT0032H1
AIGT0030B
AIGT0030H
AIGT0032B
AIGT0032H
AIGT2030B
AIGT2030H
AIGT2032B
AIGT2032H
AIGT2230B
AIGT2230H
AIGT2232B
AIGT2232H
AFPX-COM2
2 W or less *2
Approx. 20 g
AFPX-COM3
2 W or less *2
Approx. 20 g
AFPX-COM4
2 W or less *2
Approx. 20 g
AFPX-COM5
2 W or less *2
Approx. 20 g
AFPX-AD2
2 W or less *2
Approx. 25 g
AFPX-IN8
1 W or less *2
Approx. 25 g
AFPX-TR8
1 W or less *2
Approx. 25 g
AFPX-TR6P
1 W or less *2
Approx. 25 g
AFPX-PLS
2 W or less *2
Approx. 25 g
AFPX-MRTC
2 W or less *2
Approx. 20 g
Expansion FP0 adapter
Product name
1500 V [P-P] pulse width 50 ns, 1 µs (AC power), 500 V [P-P] pulse width 50 ns, 1 µs (DC power) (per noise simulator method) (power terminals)
No corrosive gas and no excessive dust
Conforming to EN61131-2
2
II
*1 Cutoff current 5 mA
Product name
FP2SH FP-M*
A: Available, N/A: Not available
*The production of FP1, FP-M, FP3/FP10SH has been discontinued.
STN monochrome LCD
Vibration resistance
Shock resistance
Noise immunity
Operating condition
EC Directive Compliance Standard
Level of contamination
Over-voltage category
100 to 240 V AC (AC power), 24 V DC (DC power)
85 to 264 V AC (AC power), 20.4 to 28.8 V DC (DC power)
40 A or less (C14), 45 A or less (C30, C60) at 25°C (AC power)
12 A or less at 25°C (DC power)
10 ms or more
0 to +55°C
-40 to +70°C
10 to 95% RH (at 25 °C, non-condensing)
10 to 95% RH (at 25 °C, non-condensing)
Combined input/output terminals - Combined power and ground terminals,
2300 V AC 1 minute (AC power), 500 V AC*1 1 minute (DC power)
Input terminals - Relay output terminals, 2300 V AC*1 1 minute
Input terminals - Transistor output terminals, 500 V AC*1 1 minute
Power terminals - Ground terminals, 1500 V AC*1 1 minute (AC power), 500 V AC*1 1 minute (DC power)
Combined input/output terminals - Combined power and ground terminals, 100 MΩ or higher (500 V DC using an insulation resistance meter)
Input terminals - Output terminals, 100 MΩ or higher (500 V DC using an insulation resistance meter)
Power terminals - Ground terminals, 100 MΩ or higher (500 V DC using an insulation resistance meter)
5 to 9 Hz, single amplitude 3.5 mm/9 to 150 Hz, constant acceleration 9.8 m/s2, 1 sweep/min, 10 sweeps in each XYZ direction
147 m/s2
2. Power Consumption, Weight
Control FPWIN Pro (IEC61131-3 compliant Windows version software)
Product name
Description
Item
Rated voltage
Operating voltage range
Rush current
FP0-A21
FP0 Link Units
Product name
1. General Specifications
FP-X communication cassette
FP-X analog input cassette
FP-X input cassette
FP-X output cassette
FP-X pulse I/O cassette
FP-X master memory cassette
*2 Power consumption by the AC power supply connected to the control unit
*4 Please refer to FP0 users manual for FP0 expansion units.
Please refer to the user manual and specifications for further details.
*3 Power consumption by the DC power supply connected to the expansion FP0 adapter
17
Specifications
Specifications
4. Input Specifications (Control unit, expansion unit)
3. Controls Specifications
Item
Relay symbol method
Program method
Cyclic operation method
Control method
Program memory
Flash ROM built-in (no battery backup required)
Program capacity
16 ksteps (C14), 32 ksteps (C30, C60)
Basic instruction 0.32 µs/step
Operation processing speed
Basic instructions
111
Applied instructions
216
External inputs (X)
1760 points *4
External outputs (Y)
1760 points *4
Internal relay (R)
4096 points
Special internal relay (R)
192 points
Link relay (L)
2048 points
21.6 to 26.4 V DC
Operating voltage range
Approx. 8 mA (Control unit X0 to X3)
Approx. 4.7 mA (Control unit X0 to X7)
Approx. 4.7 mA (Control unit X4 to X7)
Rated input current
Approx 4.3 mA (Control unit X8 and after, expansion unit)
Approx. 4.3 mA (Control unit X8 and after, expansion unit)
8 points/common (C14, E16) 16 points/common (C30, C60)
Input points per common
(Input power polarity either positive or negative)
Min. ON voltage/ON current
19.2 V/3 mA
Max. OFF voltage/OFF current
2.4 V/1 mA
19.2 V/6 mA (Control unit X0 to X3)
19.2 V/3 mA (Control unit X4 and after, expansion unit)
2.4 V/1.3 mA (Control unit X0 to X3)
2.4 V/1 mA (Control unit X4 and after, expansion unit)
Approx. 3 kΩ (Control unit X0 to X3)
Approx. 5.1 kΩ (Control unit X4 to X7)
Approx. 5.6 kΩ (Control unit X8 and after, expansion unit)
Approx. 5.1 kΩ (Control unit X0 to X7)
Approx. 5.6 kΩ (Control unit X8 and after, expansion unit)
Input impedance
Control unit X0 to X7
12285 words (C14), 32765 words (C3R, C60)
256 words
Special data register (DT)
374 words
Response OFF → ON
Index register (I0 to ID)
14 words
time
Master control relay (MCR)
256 points
Number of labels (LOOP)
256 labels
Number of differentiations
Up to program capacity
Number of stepladders
1000 stages
Number of subroutines
500 subroutines
Number of interruption programs
High-speed counter *5
Control unit X8 and after, expansion unit
Built-in (Relay output): single-phase 8 ch (10 kHz x 8 ch)
Built-in (Transistor output): 100 kHz x 2 ch + 20 kHz x 2 ch
Relay output type: Total 14 points (including the high-speed counter)
ON → OFF
0.5 ms to 30 s
Possible
Constant scan
Equipped (usable only when AFPX-MRTC is installed) *7
Item
Description
Rated control capacity (Resistive load)
2 A 250 V AC, 2 A 30 V DC (8 A or less/common)
Output type
1a contact
Output points per common
Response time
Life time
Battery backup
Counter 16 points (1008 to 1023), Internal relay 128 points (R2470 to R255F), Data register 55 words
Approx. 8 ms
Mechanical
20 million operations or more (Operation frequency 180 times/min)
Electrical
None
After installing AFPX-MRTC
C14: 1230 days (actual operation 10 years at 25°C)
Item
Description
Insulation method
Photocoupler
Open collector
Output type
C14: 780 days (actual operation 10 years at 25°C)
Rated loadf voltage
C30, C60: 680 days (actual operation 10 years at 25°C)
Load voltage allowable range
Capable (4 or 8 characters selectable)
Capable (328 KB) (backup battery not required)
OFF state leakage current
PLC link function
Max 16 units, link relay 1024 points, link register 128 words (No data transfer or remote programming)
The actual usable number of points is restricted by the hardware.
Specification at the rated input voltage of 24 V DC, 25°C. Frequency may be lower due to the voltage and temperature.
Max frequency may vary by the method of operation. Please refer to the manual for details.
Calendar accuracy at 0°C: 119 sec/month or less, 25°C: 51 sec/month or less, 55°C: 148 sec/month or less (Real-time clock requires a battery.)
When data is stored in the storage area while the battery is not installed, the data is not cleared and the data value may be indefinite.
The same condition occurs when the battery is exhausted.
*9 The number of possible rewrites is 10,000 or less.
NPN type: 4.75 to 26.4 V DC, PNP type: 21.6 to 26.4 V DC
0.5 A
1.5 A
Max. inrush current
Comment storage
Capable
NPN type: 5 to 24 V DC, PNP type: 24 V DC
Max. load current
Output points per common
Rewriting in RUN mode
LED display
6. Transistor Output Specifications
Watch dog timer, program syntax check
Self-diagnosis function
100,000 operations or more (Operation frequency 20 times/min at the rated control capacity)
Operating indicator
C30, C60: 990 days (actual operation 10 years at 25°C)
(More than two batteries can be installed in C30 and C60. In this case, the battery life is extended several times)
Password
Approx. 10 ms
ON → OFF
Surge absorber
The memory allocated in the storage area by the system register (only when a battery is installed) *8
Before installing AFPX-MRTC
Battery life (when no power is supplied)
4 points/common
OFF → ON
Data register (32765 words)
Backup by F12, P13 commands
Auto-backup at power failure
LED display
5. Relay Output Specifications (Control units, Expansion units)
2 points (0 to 1000) (C14, C30) 4 points (0 to 1000) (C60)
Real-time clock
Same as above
*1 Specification at the rated input voltage of 24 V DC, 25°C.
Transistor output type: Total 8 points (including the high-speed counter)
Periodical interrupt
Potentiometer
Control unit X4 to X7
135 µs or less: Nominal input
50 µs or less: High-speed counter, pulse catch, interruption input setting*1
Control unit X8 and after, expansion unit
0.6 ms or less
Operating indicator
Pulse I/O cassette (AFPX-PLS) for relay output type: One unit (one axis) 100 kHz, or two units (two axes) 80 kHz
Pulse catch input / interrupt input
Control unit X0 to X3
135 µs or less: Nominal input
5 µs or less: High-speed counter, pulse catch, interruption input setting*1
Relay output type: 15 programs (14 external, 1 constant)
Transistor output type: 9 programs (8 external, 1 constant)
Pulse I/O cassette (AFPX-PLS) for relay output type: single-phase 2 ch (80 kHz x 2 ch)
Pulse output *6
0.6 ms or less: Normal input
50 ms or less: High-speed counter, pulse catch, interruption input setting *1
0.6 ms or less
Built-in (Transistor output): single-phase 8 ch (50 kHz x 4 ch + 10 kHz x 4 ch)
18
24 V DC
Rated input voltage
Link data register (LD)
*4
*5
*6
*7
*8
Transistor output
Photo-coupler
Counter capable of counting 1 to 32767
Data register (DT)
Flash ROM
backup *9
Relay output
Insulation method
Total 1024 points: timer capable of counting (1 ms, 10 ms, 100 ms, 1 s) x 32767
Timer/counter (T/C)
Description
Item
Specifications
8 points/common (C14, E16)
ON state voltage drop
Response time
OFF → ON
ON → OFF
Voltage range for external power supply
8 points/common, 6 points/common (C30, C60, E30)
1 µA or less
0.3 V DC or less
1 ms or less*2
1 ms or less*2
21.6 to 26.4 V DC
Surge absorber
Zener diode
Operating indicator
LED display
*2 Please refer to the user manual for Y0 to Y7 of the transistor output type.
19
Specifications
Specifications
4. Input Specifications (Control unit, expansion unit)
3. Controls Specifications
Item
Relay symbol method
Program method
Cyclic operation method
Control method
Program memory
Flash ROM built-in (no battery backup required)
Program capacity
16 ksteps (C14), 32 ksteps (C30, C60)
Basic instruction 0.32 µs/step
Operation processing speed
Basic instructions
111
Applied instructions
216
External inputs (X)
1760 points *4
External outputs (Y)
1760 points *4
Internal relay (R)
4096 points
Special internal relay (R)
192 points
Link relay (L)
2048 points
21.6 to 26.4 V DC
Operating voltage range
Approx. 8 mA (Control unit X0 to X3)
Approx. 4.7 mA (Control unit X0 to X7)
Approx. 4.7 mA (Control unit X4 to X7)
Rated input current
Approx 4.3 mA (Control unit X8 and after, expansion unit)
Approx. 4.3 mA (Control unit X8 and after, expansion unit)
8 points/common (C14, E16) 16 points/common (C30, C60)
Input points per common
(Input power polarity either positive or negative)
Min. ON voltage/ON current
19.2 V/3 mA
Max. OFF voltage/OFF current
2.4 V/1 mA
19.2 V/6 mA (Control unit X0 to X3)
19.2 V/3 mA (Control unit X4 and after, expansion unit)
2.4 V/1.3 mA (Control unit X0 to X3)
2.4 V/1 mA (Control unit X4 and after, expansion unit)
Approx. 3 kΩ (Control unit X0 to X3)
Approx. 5.1 kΩ (Control unit X4 to X7)
Approx. 5.6 kΩ (Control unit X8 and after, expansion unit)
Approx. 5.1 kΩ (Control unit X0 to X7)
Approx. 5.6 kΩ (Control unit X8 and after, expansion unit)
Input impedance
Control unit X0 to X7
12285 words (C14), 32765 words (C3R, C60)
256 words
Special data register (DT)
374 words
Response OFF → ON
Index register (I0 to ID)
14 words
time
Master control relay (MCR)
256 points
Number of labels (LOOP)
256 labels
Number of differentiations
Up to program capacity
Number of stepladders
1000 stages
Number of subroutines
500 subroutines
Number of interruption programs
High-speed counter *5
Control unit X8 and after, expansion unit
Built-in (Relay output): single-phase 8 ch (10 kHz x 8 ch)
Built-in (Transistor output): 100 kHz x 2 ch + 20 kHz x 2 ch
Relay output type: Total 14 points (including the high-speed counter)
ON → OFF
0.5 ms to 30 s
Possible
Constant scan
Equipped (usable only when AFPX-MRTC is installed) *7
Item
Description
Rated control capacity (Resistive load)
2 A 250 V AC, 2 A 30 V DC (8 A or less/common)
Output type
1a contact
Output points per common
Response time
Life time
Battery backup
Counter 16 points (1008 to 1023), Internal relay 128 points (R2470 to R255F), Data register 55 words
Approx. 8 ms
Mechanical
20 million operations or more (Operation frequency 180 times/min)
Electrical
None
After installing AFPX-MRTC
C14: 1230 days (actual operation 10 years at 25°C)
Item
Description
Insulation method
Photocoupler
Open collector
Output type
C14: 780 days (actual operation 10 years at 25°C)
Rated loadf voltage
C30, C60: 680 days (actual operation 10 years at 25°C)
Load voltage allowable range
Capable (4 or 8 characters selectable)
Capable (328 KB) (backup battery not required)
OFF state leakage current
PLC link function
Max 16 units, link relay 1024 points, link register 128 words (No data transfer or remote programming)
The actual usable number of points is restricted by the hardware.
Specification at the rated input voltage of 24 V DC, 25°C. Frequency may be lower due to the voltage and temperature.
Max frequency may vary by the method of operation. Please refer to the manual for details.
Calendar accuracy at 0°C: 119 sec/month or less, 25°C: 51 sec/month or less, 55°C: 148 sec/month or less (Real-time clock requires a battery.)
When data is stored in the storage area while the battery is not installed, the data is not cleared and the data value may be indefinite.
The same condition occurs when the battery is exhausted.
*9 The number of possible rewrites is 10,000 or less.
NPN type: 4.75 to 26.4 V DC, PNP type: 21.6 to 26.4 V DC
0.5 A
1.5 A
Max. inrush current
Comment storage
Capable
NPN type: 5 to 24 V DC, PNP type: 24 V DC
Max. load current
Output points per common
Rewriting in RUN mode
LED display
6. Transistor Output Specifications
Watch dog timer, program syntax check
Self-diagnosis function
100,000 operations or more (Operation frequency 20 times/min at the rated control capacity)
Operating indicator
C30, C60: 990 days (actual operation 10 years at 25°C)
(More than two batteries can be installed in C30 and C60. In this case, the battery life is extended several times)
Password
Approx. 10 ms
ON → OFF
Surge absorber
The memory allocated in the storage area by the system register (only when a battery is installed) *8
Before installing AFPX-MRTC
Battery life (when no power is supplied)
4 points/common
OFF → ON
Data register (32765 words)
Backup by F12, P13 commands
Auto-backup at power failure
LED display
5. Relay Output Specifications (Control units, Expansion units)
2 points (0 to 1000) (C14, C30) 4 points (0 to 1000) (C60)
Real-time clock
Same as above
*1 Specification at the rated input voltage of 24 V DC, 25°C.
Transistor output type: Total 8 points (including the high-speed counter)
Periodical interrupt
Potentiometer
Control unit X4 to X7
135 µs or less: Nominal input
50 µs or less: High-speed counter, pulse catch, interruption input setting*1
Control unit X8 and after, expansion unit
0.6 ms or less
Operating indicator
Pulse I/O cassette (AFPX-PLS) for relay output type: One unit (one axis) 100 kHz, or two units (two axes) 80 kHz
Pulse catch input / interrupt input
Control unit X0 to X3
135 µs or less: Nominal input
5 µs or less: High-speed counter, pulse catch, interruption input setting*1
Relay output type: 15 programs (14 external, 1 constant)
Transistor output type: 9 programs (8 external, 1 constant)
Pulse I/O cassette (AFPX-PLS) for relay output type: single-phase 2 ch (80 kHz x 2 ch)
Pulse output *6
0.6 ms or less: Normal input
50 ms or less: High-speed counter, pulse catch, interruption input setting *1
0.6 ms or less
Built-in (Transistor output): single-phase 8 ch (50 kHz x 4 ch + 10 kHz x 4 ch)
18
24 V DC
Rated input voltage
Link data register (LD)
*4
*5
*6
*7
*8
Transistor output
Photo-coupler
Counter capable of counting 1 to 32767
Data register (DT)
Flash ROM
backup *9
Relay output
Insulation method
Total 1024 points: timer capable of counting (1 ms, 10 ms, 100 ms, 1 s) x 32767
Timer/counter (T/C)
Description
Item
Specifications
8 points/common (C14, E16)
ON state voltage drop
Response time
OFF → ON
ON → OFF
Voltage range for external power supply
8 points/common, 6 points/common (C30, C60, E30)
1 µA or less
0.3 V DC or less
1 ms or less*2
1 ms or less*2
21.6 to 26.4 V DC
Surge absorber
Zener diode
Operating indicator
LED display
*2 Please refer to the user manual for Y0 to Y7 of the transistor output type.
19
■ FP-X Control Unit Dimensions (Unit: mm)
Dimensions when expansion cassettes
(function and communication) are installed
●AFPX-C14 ∗ ∗ (The same dimensions apply to the expansion I/O unit AFPX-E16∗)
COM
Status display LED
N
X0
X2
X5
X4
X7
X6
PROG. ERR.
3
7
3
0
X 4
0
Y
4
Programmable Controller
45
L
RUN
Input/output display LED
Application cassette
Communication cassette
X3
X1
FP-X
60
5
90
Panasonic
RUN
PROG.
Mode selection switch
RUN/PROG.
FP-X C14
min.
max.
V0
V1
45
Analog volume
Tool port connector
0V
Y2
Y1
Y0
24V
C0
C1
C2
Y3
C3
Y5
Y4
13.6
3.5
Application cassette
Communication cassette
Battery
Expansion unit connector
79
8.6
79
●AFPX-C30 ∗ ∗ (The same dimensions apply to the expansion I/O unit AFPX-E30∗ ∗)
100
Mounting dimension diagram
Status display LED
N COM
L
COM
RUN
Input/output display LED
X1
X0
X3
X2
X5
X4
X7
X9
X8
X6
XB
XA
XD
XC
Introducing a New Transistor Output Model
Pulse Output
XF
XE
2-M
4o
r2
PROG. ERR.
0
8
0
Y
8
7
F
7
X
D
-
5
90
FP-X C30
RUN
PROG.
min.
82 ±0.5
Panasonic
Mode selection switch
RUN/PROG.
max.
4-Axis Integrated Control
V0
Analog volume
V1
0V
USB connector
24V
Tool port connector
Y0
C0
Y2
Y1
C1
C2
Y4
Y3
Y7
C3
Y5
Y6
Y9
Y8
YA
C4
YC
YB
YD
Cassette attachment area 1 Cassette attachment area 2
Application cassette
Communication cassette
Battery
FP-X C14
Function cassette
Battery
Expansion unit connector
●AFPX-C60 ∗ ∗
52 ±0.5
92 ±0.5
FP-X C30
ARCT1B273E
DIN hook
Cassette attachment area 1
182 ±0.5
FP-X C60
190
N COM
L
COM
RUN
X
Y
Mode selection switch
RUN/PROG.
X0
PROG.
X3
X2
X5
X4
7 8
17 18
7 8
17 18
XC
COM
NC
XF
XE
COM
COM
COM
X11
X13
X12
X10
X15
X14
X17
X16
X19
X18
X1B
X1A
X1D
X1C
X1F
X1E
F
1F
D
1D
FP-X C60
V1
V2
max.
V3
0V
Tool port connector
XA
XD
max.
V0
min.
USB connector
X8
XB
Panasonic
min.
24V
X6
X9
ERR.
0
10
0
10
RUN
PROG.
Analog volume
X7
Y0
C0
Y2
Y1
C1
C2
Y4
Y3
Y7
C3
Y5
Y6
Y9
Y8
YA
C4
YC
YB
Y10
YD
Cassette attachment area 1
Application cassette
Communication cassette
Battery
C0
Y11
C1
C2
Y12
Y13
C3
C5
Y14
C4
Y15
Y17
Y16
Y19
Y18
Y1A
C6
Y1C
Y1B
Cassette attachment area 2
Application cassette
Battery
Y1D
Expansion connector part
Battery
Expansion unit connector
■ FP-X Expansion FP0 Adapter Dimensions (Unit: mm)
( 0.5 )
25
60
POWER
I/F
L
ERROR
45
Status
display LED
(7)
Panasonic
Expansion connector
90
AFPX-EFP0
FP0-A80
When the expansion
connector is
attached
45
Input/output display LED
X1
90
Status display LED
2-Axis Linear
Interpolation
Simultaneously
in 2 Pairs!
Appearance when mounted
with a C14 control unit
3.5
DIN hook
Power connector 24 V DC
Expansion hook
These materials are printed on ECF pulp.
These materials are printed with earth-friendly vegetable-based (soybean oil) ink.
Please contact ..........
Matsushita Electric Works, Ltd.
Automation Controls Business Unit
Head Office: 1048, Kadoma, Kadoma-shi, Osaka 571-8686, Japan
14-point type
FP-X Programmable Controller
ARCT1B273E ’06.8
All Rights Reserved © 2006 COPYRIGHT Matsushita Electric Works, Ltd.
ARCT1B273E 200608-6YT
Specifications are subject to change without notice.
Printed in Japan.
30-point type
http://www.nais-e.com/plc/
Panasonic... the new name for
60-point type
New
Matsushita Electric Works, Ltd.
Similar pages