Renesas HM628511CJPI12 Wide temperature range version 4m high speed sram (512-kword ã 8-bit) Datasheet

To all our customers
Regarding the change of names mentioned in the document, such as Hitachi
Electric and Hitachi XX, to Renesas Technology Corp.
The semiconductor operations of Mitsubishi Electric and Hitachi were transferred to Renesas
Technology Corporation on April 1st 2003. These operations include microcomputer, logic, analog
and discrete devices, and memory chips other than DRAMs (flash memory, SRAMs etc.)
Accordingly, although Hitachi, Hitachi, Ltd., Hitachi Semiconductors, and other Hitachi brand
names are mentioned in the document, these names have in fact all been changed to Renesas
Technology Corp. Thank you for your understanding. Except for our corporate trademark, logo and
corporate statement, no changes whatsoever have been made to the contents of the document, and
these changes do not constitute any alteration to the contents of the document itself.
Renesas Technology Home Page: http://www.renesas.com
Renesas Technology Corp.
Customer Support Dept.
April 1, 2003
Cautions
Keep safety first in your circuit designs!
1. Renesas Technology Corporation puts the maximum effort into making semiconductor products better
and more reliable, but there is always the possibility that trouble may occur with them. Trouble with
semiconductors may lead to personal injury, fire or property damage.
Remember to give due consideration to safety when making your circuit designs, with appropriate
measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or
(iii) prevention against any malfunction or mishap.
Notes regarding these materials
1. These materials are intended as a reference to assist our customers in the selection of the Renesas
Technology Corporation product best suited to the customer's application; they do not convey any
license under any intellectual property rights, or any other rights, belonging to Renesas Technology
Corporation or a third party.
2. Renesas Technology Corporation assumes no responsibility for any damage, or infringement of any
third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or
circuit application examples contained in these materials.
3. All information contained in these materials, including product data, diagrams, charts, programs and
algorithms represents information on products at the time of publication of these materials, and are
subject to change by Renesas Technology Corporation without notice due to product improvements or
other reasons. It is therefore recommended that customers contact Renesas Technology Corporation
or an authorized Renesas Technology Corporation product distributor for the latest product information
before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors.
Renesas Technology Corporation assumes no responsibility for any damage, liability, or other loss
rising from these inaccuracies or errors.
Please also pay attention to information published by Renesas Technology Corporation by various
means, including the Renesas Technology Corporation Semiconductor home page
(http://www.renesas.com).
4. When using any or all of the information contained in these materials, including product data, diagrams,
charts, programs, and algorithms, please be sure to evaluate all information as a total system before
making a final decision on the applicability of the information and products. Renesas Technology
Corporation assumes no responsibility for any damage, liability or other loss resulting from the
information contained herein.
5. Renesas Technology Corporation semiconductors are not designed or manufactured for use in a device
or system that is used under circumstances in which human life is potentially at stake. Please contact
Renesas Technology Corporation or an authorized Renesas Technology Corporation product distributor
when considering the use of a product contained herein for any specific purposes, such as apparatus or
systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.
6. The prior written approval of Renesas Technology Corporation is necessary to reprint or reproduce in
whole or in part these materials.
7. If these products or technologies are subject to the Japanese export control restrictions, they must be
exported under a license from the Japanese government and cannot be imported into a country other
than the approved destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the
country of destination is prohibited.
8. Please contact Renesas Technology Corporation for further details on these materials or the products
contained therein.
HM628511HCI Series
Wide Temperature Range Version
4M High Speed SRAM (512-kword × 8-bit)
ADE-203-1304A (Z)
Rev. 1.0
Nov. 30, 2001
Description
The HM628511HCI Series is a 4-Mbit high speed static RAM organized 512-k word × 8-bit. It has
realized high speed access time by employing CMOS process (6-transistor memory cell)and high speed
circuit designing technology. It is most appropriate for the application which requires high speed, high
density memory and wide bit width configuration, such as cache and buffer memory in system. It is
packaged in 400-mil 36-pin plastic SOJ.
Features
• Single 5.0 V supply: 5.0 V ± 10 %
• Access time: 12 ns (max)
• Completely static memory
 No clock or timing strobe required
• Equal access and cycle times
• Directly TTL compatible
 All inputs and outputs
• Operating current: 130 mA (max)
• TTL standby current: 40 mA (max)
• CMOS standby current : 5 mA (max)
• Center VCC and VSS type pin out
• Temperature range : –40 to +85°C
Ordering Information
Type No.
Access time
Device marking
Package
HM628511HCJPI-12
12 ns
HM628511CJPI12
400-mil 36-pin plastic SOJ (CP-36D)
HM628511HCI Series
Pin Arrangement
36-pin SOJ
A0
1
36
NC
A1
2
35
A18
A2
3
34
A17
A3
4
33
A16
A4
5
32
A15
6
31
I/O1
7
30
I/O8
I/O2
8
29
I/O7
VCC
9
28
VSS
VSS
10
27
VCC
I/O3
11
26
I/O6
I/O4
12
25
I/O5
13
24
A14
A5
14
23
A13
A6
15
22
A12
A7
16
21
A11
A8
17
20
A10
A9
18
19
NC
(Top View)
Pin Description
Pin name
Function
A0 to A18
Address input
I/O1 to I/O8
Data input/output
CS
Chip select
OE
Output enable
WE
Write enable
VCC
Power supply
VSS
Ground
NC
No connection
Rev. 1, Nov. 2001, page 2 of 2
HM628511HCI Series
Block Diagram
(LSB)
A14
A13
A12
A5
A6
A7
A11
A10
A3
A1
(MSB)
Internal
voltage
generator
Row
decoder
1024-row × 32-column ×
16-block × 8-bit
(4,194,304 bits)
VCC
VSS
CS
Column I/O
I/O1
.
.
Input
data
control
Column decoder
CS
.
I/O8
A8 A9 A18 A16 A17 A0 A2 A4 A15
(LSB)
WE
CS
(MSB)
OE
CS
Rev. 1, Nov. 2001, page 3 of 3
HM628511HCI Series
Operation Table
CS
OE
WE
Mode
VCC current
I/O
Ref. cycle
H
×
×
Standby
ISB, ISB1
High-Z
—
L
H
H
Output disable
ICC
High-Z
—
L
L
H
Read
ICC
Dout
Read cycle (1) to (3)
L
H
L
Write
ICC
Din
Write cycle (1)
L
L
L
Write
ICC
Din
Write cycle (2)
Parameter
Symbol
Value
Supply voltage relative to VSS
VCC
–0.5 to +7.0
Note:
H: VIH, L: VIL, ×: VIH or VIL
Absolute Maximum Ratings
Unit
V
1
2
Voltage on any pin relative to VSS
VT
–0.5* to VCC+0.5*
V
Power dissipation
PT
1.0
Operating temperature
Topr
–40 to +85
°C
Storage temperature
Tstg
–55 to +125
°C
Storage temperature under bias
Tbias
–40 to +85
°C
W
Notes: 1. VT (min) = –2.0 V for pulse width (under shoot) ≤ 6 ns.
2. VT (max) = VCC+2.0 V for pulse width (over shoot) ≤ 6 ns.
Recommended DC Operating Conditions
(Ta = –40 to +85°C)
Parameter
Symbol
Supply voltage
Input voltage
VIH
VIL
Notes: 1.
2.
3.
4.
Typ
Unit
4.5
5.0
5.5
V
0
0
0
V
2.2
—
VCC + 0.5*
—
0.8
–0.5*
1
VIL (min) = –2.0 V for pulse width (under shoot) ≤ 6 ns.
VIH (max) = VCC+2.0 V for pulse width (over shoot) ≤ 6 ns.
The supply voltage with all VCC pins must be on the same level.
The supply voltage with all VSS pins must be on the same level.
Rev. 1, Nov. 2001, page 4 of 4
Max
4
VCC*
VSS*
Min
3
2
V
V
HM628511HCI Series
DC Characteristics
(Ta = –40 to +85°C, VCC = 5.0 V ± 10 %, VSS = 0V)
Parameter
Symbol Min
Typ*
Input leakage current
IILII
—
Output leakage current
IILOI
1
Max
Unit
Test conditions
—
2
µA
Vin = VSS to VCC
—
—
2
µA
Vin = VSS to VCC
Operation power supply current ICC
—
—
130
mA
Min cycle
CS = VIL, lout = 0 mA
Other inputs = VIH/VIL
Standby power supply current
ISB
—
—
40
mA
Min cycle, CS = VIH,
Other inputs = VIH/VIL
ISB1
—
2.5
5
mA
f = 0 MHz
VCC ≥ CS ≥ VCC - 0.2 V,
(1) 0 V ≤ Vin ≤ 0.2 V or
(2) VCC ≥ Vin ≥ VCC - 0.2 V
Output voltage
VOL
—
—
0.4
V
IOL = 8 mA
VOH
2.4
—
—
V
IOH = –4 mA
Notes: 1. Typical values are at VCC = 5.0 V, Ta = +25°C and not guaranteed.
Capacitance
(Ta = +25°C, f = 1.0 MHz)
Parameter
Input capacitance*
1
Input/output capacitance*
Note:
1
Symbol
Min
Typ
Max
Unit
Test conditions
Cin
—
—
6
pF
Vin = 0 V
CI/O
—
—
8
pF
VI/O = 0 V
1. This parameter is sampled and not 100% tested.
Rev. 1, Nov. 2001, page 5 of 5
HM628511HCI Series
AC Characteristics
(Ta = –40 to +85°C, VCC = 5.0 V ± 10 %, unless otherwise noted.)
Test Conditions
• Input pulse levels: 3.0 V/0.0 V
• Input rise and fall time: 3 ns
• Input and output timing reference levels: 1.5 V
• Output load: See figures (Including scope and jig)
5V
1.5 V
Dout Zo=50 Ω
RL=50 Ω
480Ω
Dout
255Ω
30 pF
5 pF
Output load (B)
(for tCLZ, tOLZ, tCHZ, tOHZ, tWHZ, and tOW)
Output load (A)
Read Cycle
HM628511HCI
-12
Parameter
Symbol
Min
Max
Unit
Read cycle time
tRC
12
—
ns
Address access time
tAA
—
12
ns
Chip select access time
tACS
—
12
ns
Output enable to output valid
tOE
—
6
ns
Output hold from address change
tOH
3
—
ns
Chip select to output in low-Z
tCLZ
3
—
ns
1
Output enable to output in low-Z
tOLZ
0
—
ns
1
Chip deselect to output in high-Z
tCHZ
—
6
ns
1
Output disable to output in high-Z
tOHZ
—
6
ns
1
Rev. 1, Nov. 2001, page 6 of 6
Notes
HM628511HCI Series
Write Cycle
HM628511HCI
-12
Parameter
Symbol
Min
Max
Unit
Notes
Write cycle time
tWC
12
—
ns
Address valid to end of write
tAW
8
—
ns
Chip select to end of write
tCW
8
—
ns
9
Write pulse width
tWP
8
—
ns
8
Address setup time
tAS
0
—
ns
6
Write recovery time
tWR
0
—
ns
7
Data to write time overlap
tDW
6
—
ns
Data hold from write time
tDH
0
—
ns
Write disable to output in low-Z
tOW
3
—
ns
1
Output disable to output in high-Z
tOHZ
—
6
ns
1
Write enable to output in high-Z
tWHZ
—
6
ns
1
Notes: 1. Transition is measured ±200 mV from steady voltage with output load (B). This parameter is
sampled and not 100% tested.
2. Address should be valid prior to or coincident with CS transition low.
3. WE and/or CS must be high during address transition time.
4. If CS and OE are low during this period, I/O pins are in the output state. Then, the data input
signals of opposite phase to the outputs must not be applied to them.
5. If the CS low transition occurs simultaneously with the WE low transition or after the WE
transition, output remains a high impedance state.
6. tAS is measured from the latest address transition to the later of CS or WE going low.
7. tWR is measured from the earlier of CS or WE going high to the first address transition.
8. A write occurs during the overlap of a low CS and a low WE. A write begins at the latest
transition among CS going low and WE going low. A write ends at the earliest transition among
CS going high and WE going high. tWP is measured from the beginning of write to the end of
write.
9. tCW is measured from the later of CS going low to the end of write.
Rev. 1, Nov. 2001, page 7 of 7
HM628511HCI Series
Timing Waveforms
Read Timing Waveform (1) (WE = VIH)
tRC
Address
Valid address
tOH
tAA
tACS
CS
tOE
tCHZ
tOHZ
OE
tOLZ
tCLZ
Dout
High impedance
Valid data
Read Timing Waveform (2) (WE = VIH, CS = VIL, OE = VIL)
tRC
Address
Valid address
tAA
tOH
tOH
Dout
Rev. 1, Nov. 2001, page 8 of 8
Valid data
HM628511HCI Series
Read Timing Waveform (3) (WE = VIH, CS = VIL, OE = VIL)*
2
tRC
CS
tACS
tCHZ
tCLZ
Dout
High
impedance
Valid data
High
impedance
Write Timing Waveform (1) (WE Controlled)
tWC
Valid address
Address
tWR
tAW
tCW
*3
tAS
tWP
*3
tOHZ
High impedance*5
Dout
tDW
Din
*4
tDH
Valid data
*4
Rev. 1, Nov. 2001, page 9 of 9
HM628511HCI Series
Write Timing Waveform (2) (CS Controlled)
tWC
Valid address
Address
tWR
tCW
*3
tAW
tWP
*3
tAS
tWHZ
tOW
High impedance*5
Dout
tDW
Din
Rev. 1, Nov. 2001, page 10 of 10
*4
tDH
Valid data
*4
HM628511HCI Series
Package Dimensions
HM628511HCJPI Series (CP-36D)
As of January, 2001
Unit: mm
23.25
23.62 Max
10.16 ± 0.13
*0.43 ± 0.10
0.41 ± 0.08
1.27
0.80 +0.25
–0.17
1.30 Max
2.85 ± 0.12
18
0.74
3.50 ± 0.26
1
11.18 ± 0.13
19
36
9.40 ± 0.25
0.10
*Dimension including the plating thickness
Base material dimension
Hitachi Code
JEDEC
EIAJ
Mass (reference value)
CP-36D
Conforms
Conforms
1.4 g
Rev. 1, Nov. 2001, page 11 of 11
HM628511HCI Series
Disclaimer
1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent,
copyright, trademark, or other intellectual property rights for information contained in this document.
Hitachi bears no responsibility for problems that may arise with third party’s rights, including
intellectual property rights, in connection with use of the information contained in this document.
2. Products and product specifications may be subject to change without notice. Confirm that you have
received the latest product standards or specifications before final design, purchase or use.
3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However,
contact Hitachi’s sales office before using the product in an application that demands especially high
quality and reliability or where its failure or malfunction may directly threaten human life or cause risk
of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation,
traffic, safety equipment or medical equipment for life support.
4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly
for maximum rating, operating supply voltage range, heat radiation characteristics, installation
conditions and other characteristics. Hitachi bears no responsibility for failure or damage when used
beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable
failure rates or failure modes in semiconductor devices and employ systemic measures such as failsafes, so that the equipment incorporating Hitachi product does not cause bodily injury, fire or other
consequential damage due to operation of the Hitachi product.
5. This product is not designed to be radiation resistant.
6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without
written approval from Hitachi.
7. Contact Hitachi’s sales office for any questions regarding this document or Hitachi semiconductor
products.
Sales Offices
Hitachi, Ltd.
Semiconductor & Integrated Circuits
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Tel: (03) 3270-2111 Fax: (03) 3270-5109
URL
http://www.hitachisemiconductor.com/
For further information write to:
Hitachi Semiconductor
(America) Inc.
179 East Tasman Drive
San Jose,CA 95134
Tel: <1> (408) 433-1990
Fax: <1>(408) 433-0223
Hitachi Europe Ltd.
Electronic Components Group
Whitebrook Park
Lower Cookham Road
Maidenhead
Berkshire SL6 8YA, United Kingdom
Tel: <44> (1628) 585000
Fax: <44> (1628) 585200
Hitachi Asia Ltd.
Hitachi Tower
16 Collyer Quay #20-00
Singapore 049318
Tel : <65>-538-6533/538-8577
Fax : <65>-538-6933/538-3877
URL : http://semiconductor.hitachi.com.sg
Hitachi Europe GmbH
Electronic Components Group
Dornacher Straße 3
D-85622 Feldkirchen
Postfach 201, D-85619 Feldkirchen
Germany
Tel: <49> (89) 9 9180-0
Fax: <49> (89) 9 29 30 00
Hitachi Asia Ltd.
(Taipei Branch Office)
4/F, No. 167, Tun Hwa North Road
Hung-Kuo Building
Taipei (105), Taiwan
Tel : <886>-(2)-2718-3666
Fax : <886>-(2)-2718-8180
Telex : 23222 HAS-TP
URL : http://www.hitachi.com.tw
Hitachi Asia (Hong Kong) Ltd.
Group III (Electronic Components)
7/F., North Tower
World Finance Centre,
Harbour City, Canton Road
Tsim Sha Tsui, Kowloon Hong Kong
Tel : <852>-(2)-735-9218
Fax : <852>-(2)-730-0281
URL : http://semiconductor.hitachi.com.hk
Copyright © Hitachi, Ltd., 2001. All rights reserved. Printed in Japan.
Colophon 5.0
Rev. 1, Nov. 2001, page 12 of 12
Similar pages