TDK ATB2012E50011TL Balun transformers wound smd Datasheet

R F
C o m p o n e n t s
July 2013
Balun Transformers
Wound SMD
ATB series
ATB2012-50011 (2.0u1.2u1.2mm)
ATB2012-75011 (2.0u1.2u1.2mm)
ATB2012E-50011M (2.0u1.2u1.0mm)
ATB2012E-75011M (2.0u1.2u1.0mm)
(2/13)
R F
C o m p o n e n t s
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 6 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or
less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
001-01 / 20130723 / e751_woundbalun_atb.fm
(3/13)
R F
C o m p o n e n t s
Balun Transformers
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
Wound SMD
Overview of the ATB Series
FEATURES
Chip balun transformer developed for impedance systems; ATB2012-50011 and ATB2012E-50011M are for 50: impedance and
ATB2012-75011 and ATB2012E-75011M are for 75: impedance.
Input impedance is 50: for ATB2012-50011 and ATB2012E-50011M, and 75: for ATB2012-75011 and ATB2012E-75011M.
The impedance ratio is 1:1.
The frequency band width for ATB2012-50011 is 40MHz to 860MHz (Standard IL = 1.0dB), for ATB2012E-50011M is 400MHz to 1.8GHz
(Standard IL =1.0dB), for ATB2012-75011is 50MHz to 1.2GHz (Standard IL = 0.8dB), and for ATB2012E-75011M is 400MHz to 1.8GHz
(Standard IL = 1.0dB).
APPLICATION
TV and mobile device tuners (DVB-T/H, ISDB-T, etc.)
STB / tuner power divider
PART NUMBER CONSTRUCTION
ATB
2012
Series name
-
L×W×H Dimensions
(mm)
2012 2.0×1.2×1.2
ATB
2012E
Series name
500
Input impedance
(:)
500
50
750
75
-
L×W×H Dimensions
(mm)
2012 2.0×1.2×1.0
11
Impedance ratio
11
500
Input impedance
(:)
500
50
750
75
1:1
T
TL
11
□□□
Packaging style
Internal code
ø180mm reel
ø330mm reel
M
Impedance ratio
11
T
1:1
-
Product
internal code
M
T
□□
Packaging style
Internal code
T
TL
ø180mm reel
ø330mm reel
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Type
Temperature range
Operating
Storage
temperature
temperature
(°C)
(°C)
ATB2012-50011
–40 to +85
–40 to +85
ATB2012-75011
–40 to +85
–40 to +85
ATB2012E-50011M
–40 to +85
–40 to +85
ATB2012E-75011M
–40 to +85
–40 to +85
Reel diameter
ø180mm
ø330mm
ø180mm
ø330mm
ø180mm
ø330mm
ø180mm
ø330mm
Package quantity
Individual weight
(pieces/reel)
2,000
10,000
2,000
10,000
2,000
10,000
2,000
10,000
(mg)
10
10
10
10
Operating temperature range includes self-temperature rise.
The Storage temperature range is for after the circuit board is mounted.
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
• All specifications are subject to change without notice.
001-01 / 20130723 / e751_woundbalun_atb.fm
(4/13)
R F
C o m p o n e n t s
Overview of the ATB Series
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T: Temperature
T4
T3
T2
T3
t3
T1
t1
t2
t: Time
Preheating
Temp.
T1
T2
150°C
180°C
Time
t1
60 to 120s
Soldering
Temp.
Time
T3
t2
230°C
10 to 30s
Peak
Temp.
T4
245°C
Time
t3
5s max.
• All specifications are subject to change without notice.
001-01 / 20130723 / e751_woundbalun_atb.fm
(5/13)
R F
C o m p o n e n t s
ATB series
ATB2012-50011 Type
SHAPE & DIMENSIONS
2.0±0.2
4
2
3
0.4
1.2±0.1
1.2±0.2
1
1.2
0.4
0.35 0.5 0.35
0.4
Dimensions in mm
RECOMMENDED LAND PATTERN
2.7
CIRCUIT DIAGRAM
Unbalanced Port
50Ω
1
Balanced Port
50Ω
4
0.4
1.2
3
0.8
2
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20130723 / e751_woundbalun_atb.fm
(6/13)
R F
C o m p o n e n t s
ATB series ATB2012-50011 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Frequency
range
(MHz)
40 to 860
UB/B
impedance
(: )
50/50
Insertion loss
(dB)
typ.
max.
1.0
2.5
CMRR
min.
20
○ Measurement equipment
Measurement item
Product No.
DC resistance
4338A
Insulation resistance
4339A
Insertion loss
E5071B
Return loss
E5071B
Amplitude imbalance
E5071B
Phase balance
E5071B
* Equivalent measurement equipment may be used.
DC
resistance
(: )max.
1.0
Rated
current
(mA)
200
Rated
voltage
(V)
20
Insulation
resistance
(M: )
10
Withstanding
voltage
(V)
125
Part No.
ATB2012-50011-T
Manufacturer
Agilent Technologies
Agilent Technologies
Agilent Technologies
Agilent Technologies
Agilent Technologies
Agilent Technologies
FREQUENCY CHARACTERISTICS
INSERTION LOSS
RETURN LOSS
0
5
1.0
Return loss (dB)
Insertion loss (dB)
0.0
2.0
3.0
4.0
5.0
6.0
20
25
35
5.0
4.0
3.0
2.0
1.0
0 100 200 300 400 500 600 700 800 900 1000
Frequency (MHz)
0 100 200 300 400 500 600 700 800 900 1000
Frequency (MHz)
PHASE BALANCE
Phase balance (deg.)
Amplitude imbalance (dB)
15
30
0 100 200 300 400 500 600 700 800 900 1000
Frequency (MHz)
AMPLITUDE IMBALANCE
0
10
185
184
183
182
181
180
179
178
177
176
175
0 100 200 300 400 500 600 700 800 900 1000
Frequency (MHz)
• All specifications are subject to change without notice.
001-01 / 20130723 / e751_woundbalun_atb.fm
(7/13)
R F
C o m p o n e n t s
ATB series
ATB2012E-50011M Type
SHAPE & DIMENSIONS
2.0±0.2
4
2
3
1.0±0.1
1.2±0.2
1
1.2
0.4
0.3
0.5
0.3
0.4
Dimensions in mm
RECOMMENDED LAND PATTERN
2.7
CIRCUIT DIAGRAM
Unbalanced Port
50:
1
Balanced Port
50:
4
0.4
1.2
3
0.8
2
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20130723 / e751_woundbalun_atb.fm
(8/13)
R F
C o m p o n e n t s
ATB series ATB2012E-50011M Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Frequency
range
(MHz)
400 to 1800
UB/B
impedance
(: )
50/50
Insertion loss
(dB)
typ.
max.
1.0
2.2
CMRR
min.
15
○ Measurement equipment
Measurement item
Product No.
DC resistance
4338A
Insulation resistance
4339A
Insertion loss
E5071B
Return loss
E5071B
Amplitude imbalance
E5071B
Phase balance
E5071B
* Equivalent measurement equipment may be used.
DC
resistance
(: )max.
0.5
Rated
current
(mA)
150
Rated
voltage
(V)
20
Insulation
resistance
(M: )
10
Withstanding
voltage
(V)
125
Part No.
ATB2012E-50011M-T
Manufacturer
Agilent Technologies
Agilent Technologies
Agilent Technologies
Agilent Technologies
Agilent Technologies
Agilent Technologies
FREQUENCY CHARACTERISTICS
0
1
2
3
4
5
6
7
8
9
0
200 400 600 800 1000 1200 1400 1500 1800
Frequency (MHz)
10
9
8
7
6
5
4
3
2
1
0
0
200 400 600 800 1000 1200 1400 1500 1800
Frequency (MHz)
0
5
10
15
20
25
30
35
40
45
0
200 400 600 800 1000 1200 1400 1500 1800
Frequency (MHz)
PHASE BALANCE
Phase balance (deg.)
AMPLITUDE IMBALANCE
Amplitude imbalance (dB)
RETURN LOSS
Return loss (dB)
Insertion loss (dB)
INSERTION LOSS
200
195
190
185
180
175
170
165
160
0
200 400 600 800 1000 1200 1400 1500 1800
Frequency (MHz)
• All specifications are subject to change without notice.
001-01 / 20130723 / e751_woundbalun_atb.fm
(9/13)
R F
C o m p o n e n t s
ATB series
ATB2012-75011Type
SHAPE & DIMENSIONS
2.0±0.2
4
2
3
0.4
1.2±0.1
1.2±0.2
1
1.2
0.4
0.35 0.5 0.35
0.4
Dimensions in mm
RECOMMENDED LAND PATTERN
CIRCUIT DIAGRAM
Unbalanced Port
75Ω
1
2.7
Balanced Port
75Ω
4
0.4
1.2
3
0.8
2
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20130723 / e751_woundbalun_atb.fm
(10/13)
R F
C o m p o n e n t s
ATB series ATB2012-75011Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Frequency
range
(MHz)
50 to 1200
UB/B
impedance
(: )
75/75
Insertion loss
(dB)
typ.
max.
0.8
1.2
CMRR
min.
20
○ Measurement equipment
Measurement item
Product No.
DC resistance
4338A
Insulation resistance
4339A
Insertion loss
E5071B
Return loss
E5071B
Amplitude imbalance
E5071B
Phase balance
E5071B
* Equivalent measurement equipment may be used.
DC
resistance
(: )
0.7
Rated
current
(mA)
280
Rated
voltage
(V)
20
Insulation
resistance
(M: )
10
Withstanding
voltage
(V)
125
Part No.
ATB2012-75011-T
Manufacturer
Agilent Technologies
Agilent Technologies
Agilent Technologies
Agilent Technologies
Agilent Technologies
Agilent Technologies
FREQUENCY CHARACTERISTICS
INSERTION LOSS
RETURN LOSS
1.0
Return loss (dB)
Insertion loss (dB)
0.0
2.0
3.0
4.0
5.0
6.0
0
200
400
600
800
Frequency (MHz)
1000
1200
3.0
2.0
1.0
0
–1.0
–2.0
–3.0
0
200
400
600
800
Frequency (MHz)
0
200
400
600
800
Frequency (MHz)
1000
1200
1000
1200
PHASE BALANCE
Phase balance (deg.)
Amplitude imbalance (dB)
AMPLITUDE IMBALANCE
0
–5
–10
–15
–20
–25
–30
–35
–40
1000
1200
190
188
186
184
182
180
178
176
174
172
170
0
200
400
600
800
Frequency (MHz)
• All specifications are subject to change without notice.
001-01 / 20130723 / e751_woundbalun_atb.fm
(11/13)
R F
C o m p o n e n t s
ATB series
ATB2012E-75011M Type
SHAPE & DIMENSIONS
2.0±0.2
4
2
3
1.0±0.1
1.2±0.2
1
1.2
0.4
0.3
0.5
0.3
0.4
Dimensions in mm
RECOMMENDED LAND PATTERN
CIRCUIT DIAGRAM
Unbalanced Port
75:
1
2.7
Balanced Port
75:
4
0.4
1.2
3
0.8
2
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20130723 / e751_woundbalun_atb.fm
(12/13)
R F
C o m p o n e n t s
ATB series ATB2012E-75011M Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Frequency
range
(MHz)
400 to 1800
UB/B
impedance
(: )
75/75
Insertion loss
(dB)
typ.
max.
1.0
2
DC
CMRR
resistance
min.
(: )max.
15
0.5
○ Measurement equipment
Measurement item
Product No.
DC resistance
4338A
Insulation resistance
4339A
Insertion loss
E5071B
Return loss
E5071B
Amplitude imbalance
E5071B
Phase balance
E5071B
* Equivalent measurement equipment may be used.
Rated
current
(mA)
150
Rated
voltage
(V)
20
Insulation
resistance
(M: )
10
Withstanding
voltage
(V)
125
Part No.
ATB2012E-75011M-T
Manufacturer
Agilent Technologies
Agilent Technologies
Agilent Technologies
Agilent Technologies
Agilent Technologies
Agilent Technologies
FREQUENCY CHARACTERISTICS
INSERTION LOSS
RETURN LOSS
1
Return loss (dB)
Insertion loss (dB)
0
2
3
4
5
6
0
200 400 600 800 1000 1200 1400 1500 1800
Frequency (MHz)
10
9
8
7
6
5
4
3
2
1
0
0
200 400 600 800 1000 1200 1400 1500 1800
Frequency (MHz)
0
200 400 600 800 1000 1200 1400 1500 1800
Frequency (MHz)
PHASE BALANCE
Phase balance (deg.)
Amplitude imbalance (dB)
AMPLITUDE IMBALANCE
0
5
10
15
20
25
30
35
40
200
195
190
185
180
175
170
165
160
0
200 400 600 800 1000 1200 1400 1500 1800
Frequency (MHz)
• All specifications are subject to change without notice.
001-01 / 20130723 / e751_woundbalun_atb.fm
(13/13)
R F
C o m p o n e n t s
ATB series
Packaging style
REEL DIMENSIONS
2.0±0.5
Type
ATB2012-50011
ATB2012-75011
N
ATB2012E-50011M
ATB2012E-75011M
A
ø180
ø330
ø180
ø330
ø180
ø330
ø180
ø330
W1
13
13.5
13
13.5
13
13.5
13
13.5
W2
60
100
60
100
60
100
60
100
N
9
10
9
10
9
10
9
10
P2
2.0±0.1
2.0±0.1
2.0±0.1
2.0±0.1
W
8.0±0.2
8.0±0.2
8.0±0.2
8.0±0.2
K
1.4±0.1
1.4±0.1
1.15±0.1
1.15±0.1
1.0
ø13.0±0.2
W1
ø21.0±0.8
W2
A
Dimensions in mm
TAPE DIMENSIONS
P2
t
P0
W
B
F
E
øD0
A
K
P1
Dimensions in mm
Type
ATB2012-50011
ATB2012-75011
ATB2012E-50011M
ATB2012E-75011M
A
1.4±0.1
1.4±0.1
1.4±0.1
1.4±0.1
B
2.25±0.1
2.25±0.1
2.25±0.1
2.25±0.1
øD0
1.5+0.1/0
1.5+0.1/0
1.5+0.1/0
1.5+0.1/0
E
1.75±0.1
1.75±0.1
1.75±0.1
1.75±0.1
F
3.5±0.1
3.5±0.1
3.5±0.1
3.5±0.1
P0
4.0±0.1
4.0±0.1
4.0±0.1
4.0±0.1
P1
4.0±0.1
4.0±0.1
4.0±0.1
4.0±0.1
t
0.25±0.05
0.25±0.05
0.2±0.05
0.2±0.05
500 to 560min.
160min.
Taping
440min.
Drawing direction
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20130723 / e751_woundbalun_atb.fm
Similar pages