NKK LB25CKW01-12GJ General specification Datasheet

Toggles
Series LB
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Other Ratings
D
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Contact Timing:
Travel:
Materials & Finishes
Housing:
Snap-in Frame:
Movable Contact:
Stationary Contacts:
Base:
Switch Terminals:
Lamp Terminals:
Slides
Rotaries
Keylocks
Programmable Illuminated PB
Pushbuttons
Power Level (silver): 3A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC
Logic Level (gold): 0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Indicators
Touch
Tilt
Tactiles
Environmental Data
Operating Temperature Range:
Humidity:
Vibration:
Shock:
Sealing:
Installation
Cap Installation Force:
Quick Connect Force:
Soldering Time & Temperature:
50 milliohms maximum for silver; 100 milliohms maximum for gold
200 megohms minimum @ 500V DC
1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts & case for 1 minute minimum
1,000,000 operations minimum for momentary circuit
200,000 operations minimum for maintained circuit
100,000 operations minimum
4.41N
Nonshorting (break-before-make)
Pretravel .059” (1.5mm); Overtravel .059” (1.5mm); Total Travel .118” (3.0mm)
Glass fiber reinforced polyamide (UL94V-0)
Stainless steel
Silver alloy or copper with gold plating
Silver alloy or copper with gold plating
Liquid crystal polymer (UL94V-0)
Phosphor bronze with silver or gold plating
Brass with silver plating
–25°C through +50°C (–13°F through +122°F) for Illuminated
–25°C through +70°C (–13°F through +158°F) for Nonilluminated
Note: When used with a polyvinyl chloride splash cover, the lowest limit is 0°C (32°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Not available for snap-in; see next section for panel seal.
3.92N maximum downward force on cap
52.95N maximum downward force on connector
Manual Soldering: See Profile A in Supplement section.
Standards & Certifications
Flammability Standards: UL94V-0 housing & base
UL: File No. E44145 - Recognized only when ordered with marking on switch.
Add “/U” or “/CUL” before first dash in part number to order UL recognized switch.
All models recognized at 3A @ 125V or 250V AC or 0.4VA @ 28V AC/DC maximum.
CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch.
Add “/C” before first dash in part number to order CSA certified switch.
All models certified at 3A @ 125V or 250V AC or 0.4VA @ 28V AC/DC maximum.
Supplement
Accessories
Standard Size Pushbuttons
D48
www.nkkswitches.com
Toggles
Series LB
Standard Size Pushbuttons
Rockers
Distinctive Characteristics
Spot illumination available in single and bicolor LEDs.
Choice of super bright LEDs in white, green, and blue
in addition to standard or bright red, amber, and
green LEDs.
D
Stainless steel clips provide secure mounting with a
wide range of panel thicknesses.
Keylocks
Latchdown feature gives indication of circuit status.
Audible and tactile feedback with smooth and
responsive operation.
Programmable Illuminated PB
Pushbuttons
Carefully designed light diffusion and filtering system produces bright,
full surface illumination with front panel relamping.
Rotaries
Snap-action contact mechanism gives long electrical
life and sensitivity of actuation.
Combination solder lug and .110” quick connect
terminals are epoxy sealed to prevent entry of flux,
dust, and other contaminants.
Slides
Panel sealed model meets IP65 of IEC60529 specifications
(similar to NEMA 4 & 13).
Tactiles
Compact switch design minimizes behind panel depth.
Actual Size
Page D48
Panel Seal
Page D59
www.nkkswitches.com
D49
Supplement
Accessories
Snap-in Mount
Indicators
Touch
Tilt
Matching indicators available.
Series LB
Toggles
Standard Size Snap-in Pushbuttons
TYPICAL SWITCH
1
Poles
D
1
SPDT
2
DPDT
5
S
Circuits
5
ON
(ON)
( ) = Momentary
6
ON
K
Shapes
ON
W01
Housing
S
Square
K
Black
C
Round
G
Gray
R
Rectangular
Alternate Action
with Latchdown
Contacts & Terminals
Rotaries
Keylocks
Programmable Illuminated PB
Pushbuttons
Rockers
LB
W01
Silver Contacts
Rated 3A @ 125/250V AC
Solder Lug/Quick Connect Terminals
G01
Gold Contacts
Rated 0.4VA @ 28V AC/DC
Solder Lug/Quick Connect Terminals
IMPORTANT:
Tactiles
Slides
Switches are supplied without UL, cULus and CSA marking unless specified.
UL, cULus & CSA recognized only when ordered with marking on the switch.
Specific models, ratings, and ordering instructions are noted on the General
Specifications page.
Tilt
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
Touch
LB15SKW01-5C12-JC
Indicators
Red, 12-volt, Bright LED with Resistor
Accessories
SPDT ON-(ON) Circuit
Supplement
Silver Contacts
Rated 3A @ 125/250V AC;
Solder Lug/Quick Connect Terminals
D50
www.nkkswitches.com
Clear Cap with Red Diffuser
Square Shape
Black Housing
Series LB
Toggles
Standard Size Snap-in Pushbuttons
ORDERING EXAMPLE
Cap Types & Colors
Incandescent Lamp Used with Solid Cap
Solid Cap: Lens/Filter Colors
05
5-volt
BJ
White/Clear
12
12-volt
CJ
Red/Clear
EJ
Yellow/Clear
FJ
Green/Clear
GJ
Blue/Clear
Nonilluminated
Incandescent or Neon Used with Insert Cap
Insert Cap: Lens/Filter Colors
01
110-volt Neon
JB
Clear/White
05
5-volt Incandescent
JC
Clear/Red
12
12-volt Incandescent
No
Code
Nonilluminated
D
JE
Clear/Yellow
* JF
Clear/Green
* JG
Clear/Blue
Keylocks
No
Code
*JF & JG not suitable with neon.
5F
Green
Clear/Red
JD
Clear/Amber
12
12-volt
JF
Clear/Green
24
24-volt
Super Bright LED Used with LED Cap
6B
White
6F
Green
6G
Blue
LED Cap: Lens/Diffuser Colors
JB
LED in Spot Illuminated Cap
Clear/White
Spot Illuminated Cap Colors
1C
Red Single Color
A
Black
1D
Amber Single Color
B
White
1F
Green Single Color
C
Red
CF
Red/Green Bicolor
F
Green
Nonilluminated
No
Code
Nonilluminated
Slides
JC
5-volt
Tilt
Amber
No Resistor
05
Touch
5D
Clear/White
Available in
Square and
Round only.
Indicators
No Code
Red
JB
Accessories
5C
Resistor
Nonilluminated Cap Colors
A
Black
F
Green
B
White
G
Blue
C
Red
H
Gray
E
Yellow
www.nkkswitches.com
Supplement
Colors
LED Cap: Lens/Diffuser Colors
Tactiles
Bright LED Used with LED Cap
Programmable Illuminated PB
Lamps
Pushbuttons
Rockers
JC
Rotaries
5C 12
D51
Series LB
Toggles
Standard Size Snap-in Pushbuttons
POLES & CIRCUITS
Rockers
Plunger Position
( ) = Momentary
Model
Normal
Down
Normal
Down
Throw & Switch/Lamp Schematics
Notes: Switch is marked with NC, NO, COM, L+, L–.
Lamp circuit is isolated and requires an
external power source.
SP
LB15
*LB16
ON
ON
(ON)
ON
1-3
1-2
SPDT
DP
LB25
*LB26
ON
ON
(ON)
ON
1-3 4-6
1-2 4-5
DPDT
D
S
.622” (15.8mm)
Square
.854” (21.7mm)
Round
C
Rotaries
NC
2
COM
NC 2
NO
6
L (+)
(-) L
L (+)
(-) L
NO
4
COM
NC
5
NO
R
(22.0) Dia
.866
.622” x .866” (15.8mm x 22.0mm)
Rectangular
(16.2)
.638
(11.5)
.453
(16.2) Sq
.638
(22.4)
.882
(1.5) R
.059
Cutout for 1 switch:
.638” x .638” (16.2mm x 16.2mm)
Cutout for 1 switch with barriers:
.638” x .815” (16.2mm x 20.7mm)
Cutout for 1 switch:
.638” x .882” (16.2mm x 22.4mm)
Cutout for 1 switch with barriers:
.638” x 1.059” (16.2mm x 26.9mm)
Panel Thickness for Switches & Barriers: .039” ~ .157” (1.0 ~ 4.0mm)
Panel Thickness for Protective Guards & Splash Covers: .039” ~ .138” (1.0 ~ 3.5mm)
HOUSING
Tactiles
Slides
COM
SHAPES & PANEL CUTOUTS
K
G
Black
Gray
Tilt
CONTACT MATERIALS, RATINGS & TERMINALS
Touch
W01
Indicators
3
1
* When in latchdown position for the alternate circuit, cap position is .039” (1.0mm) above the built-in bezel.
Housing Colors Available:
G01
Solder Lug/Quick Connect
Silver Contacts
Power Level
3A @ 125V AC & 250V AC
Gold Contacts
Logic Level
0.4VA max. @ 28V AC/DC max.
Epoxy
Seal
Optional PCB adaptors
(2.0)
AT711 & AT712 available;
.079
illustrated in “Optional
Accessories” immediately following
“Typical Switch Dimensions.”
Complete explanation of operating range in Supplement section.
(7.5)
.295
(2.8)
.110
(1.2)
.047
Thk = (0.5)
.020
INCANDESCENT & NEON LAMP CODES & SPECIFICATIONS
AT607 & AT607N
Supplement
Accessories
3
1
Keylocks
Programmable Illuminated PB
Pushbuttons
Pole
Connected Terminals
AT607 Incandescent 5-volt or
12-volt; AT607N Neon 110-volt
D52
12
01 *
Voltage
V
5V AC
12V AC
110V AC
Current
I
115mA
60mA
1.5mA
Endurance
T-1 Bi-pin
05
Avg. Hours
Ambient Temp. Range
10,000
–25°C ~ +50°C
www.nkkswitches.com
10,000
The electrical specifications shown are
determined at a basic temperature of
25°C. Lamp circuit is isolated and
requires external power source.
* Recommended Resistors for Neon:
33K ohms for 110V AC;
100K ohms for 220V AC
Series LB
Toggles
Standard Size Snap-in Pushbuttons
LED COLORS & SPECIFICATIONS
Rockers
The electrical specifications shown are determined at a basic temperature of 25°C.
LED circuit is isolated and requires external power source. Polarity marks are on the switch.
If the source voltage exceeds the rated voltage, a ballast resistor is required.
The resistor value can be calculated by using the formula in the Supplement section.
Additional lamp detail is shown in the Accessories & Hardware section.
(+)
(-)
Green
5C
5D
5F
No Code
Red
Amber
Green
Maximum Forward Current
IFM
30mA
30mA
30mA
Typical Forward Current
IF
20mA
20mA
20mA
Forward Voltage
VF
1.9V
2.0V
2.1V
Maximum Reverse Voltage
VRM
5V
5V
5V
Current Reduction Rate Above 25°C
∆IF
D
0.42mA/°C
Ambient Temperature Range
T-1 ⁄ Bi-pin
12
No Resistor
–25° ~ +50°C
Keylocks
LEDs are colored
in OFF state.
Amber
Bright LED with Resistor
Green
5C
5D
5F
Resistor Codes
05
12
24
Maximum Forward Current
IFM
—
—
—
Typical Forward Current
IF
52mA
26mA
13mA
Forward Voltage
VF
5V
12V
24V
Maximum Reverse Voltage
VRM
4V
8V
16V
Current Reduction Rate Above 25°C
∆IF
0.50mA/°C
Ambient Temperature Range
T-1 Bi-pin
AT627
5-volt
4-element (+)
with Resistor
(-)
AT627
12-volt
4-element
with Resistor
Rotaries
Amber
Slides
Color Codes:
Red
–25° ~ +50°C
(+)
(-)
Tactiles
AT627
with Resistor
Programmable Illuminated PB
Color Codes
Red
AT627
24-volt
(+)
4-element
with Resistor
(-)
Tilt
AT635
Pushbuttons
Bright LED without Resistor
ATTENTION
6G
Color
White
Green
Blue
Maximum Forward Current
IFM
30mA
30mA
30mA
Typical Forward Current
IF
20mA
20mA
20mA
Forward Voltage
VF
3.3V
3.3V
3.3V
Maximum Reverse Voltage
VRM
(-)
7V
7V
7V
Current Reduction Rate Above 25°C
∆IF
0.40mA/°C
0.40mA/°C
0.40mA/°C
T-1 Bi-pin
Ambient Temperature Range
Indicators
6F
–25° ~ +50°C
Supplement
(+)
No Code
6B
ELECTROSTATIC
SENSITIVE DEVICES
Accessories
AT625G Blue
AT631B White
AT632F Green
Touch
Super Bright Single Element LED
No Lamp
www.nkkswitches.com
D53
Series LB
Toggles
Standard Size Snap-in Pushbuttons
CAP TYPES & COLOR COMBINATIONS
Color Codes:
Rockers
Pushbuttons
Lens/Filter
Colors Available:
D
D Amber
E Yellow
F Green
G Blue
J Clear
BJ
FJ
CJ
GJ
AT476
Square
AT4012
Round
(3.5)
.138
(13.2) Sq
.520
(19.0) Dia
.748
AT4026
Rectangular
(4.5)
.177
(5.5)
.217
(13.2)
.520
Translucent Colored Lens
(19.4)
.764
(5.0)
.197
(6.0)
.236
(6.5)
.256
Transparent Clear Filter
EJ
Material: Polycarbonate
Lamp AT607
Finish: Glossy
Insert Cap for Incandescent or Neon Lamp & Nonilluminated
Lens/Filter
Colors Available:
Keylocks
Programmable Illuminated PB
C Red
Solid Cap for Incandescent Lamp & Nonilluminated
Rotaries
Slides
Tactiles
B White
JB
JF
JC
JG
AT477
Square
AT4013
Round
(3.5)
.138
(13.2) Sq
.520
(19.0) Dia
.748
AT4027
Rectangular
(4.5)
.177
(5.5)
.217
(13.2)
.520
Transparent Clear Lens
(19.4)
.764
(5.0)
.197
(6.0)
.236
(6.5)
.256
Translucent Colored Filter
JE
JF and JG not suitable
with neon lamp.
Material: Polycarbonate
Finish: Glossy
Lamp AT607 or 607N
Cap for Bright LED without Resistor
Lens/Diffuser
Colors Available:
JB
(13.2) Sq
.520
Tilt
JC
AT4176
Square
AT4178
Round
(19.0) Dia
.748
(3.5)
.138
(4.5)
.177
(13.2)
.520
Transparent Clear Lens
(19.4)
.764
(6.5)
.256
(5.0)
.197
(5.5)
.217
JD
JF
Touch
AT4177
Rectangular
Material: Polycarbonate
(6.0)
.236
Translucent Colored Diffuser
Bright LED
AT635
Finish: Glossy
Lens/Diffuser
Colors Available:
JB
Accessories
Indicators
Cap for Bright LED with Resistor
JC
Supplement
JD
AT4162
Square
AT4164
Round
AT4163
Rectangular
Transparent Clear Lens
(13.2) Sq
.520
(3.5)
.138
(6.5)
.256
(19.0) Dia
.748
(4.5)
.177
(13.2)
.520
(5.0)
.197
(6.0)
.236
(5.5)
.217
JF
Material: Polycarbonate
D54
www.nkkswitches.com
(19.4)
.764
Finish: Glossy
Translucent Colored Diffuser
Bright LED
AT627
Series LB
Toggles
Standard Size Snap-in Pushbuttons
CAP TYPES & COLOR COMBINATIONS
E Yellow
F Green
G Blue
H Gray
J Clear
AT4129
Square
(3.5)
.138
(13.2) Sq
.520
Material:
Polycarbonate
Finish: Glossy
AT4128
Round
(19.0) Dia
.748
Transparent
Clear Lens
AT4130
Rectangular
(13.2)
.520
(4.5)
.177
(5.5)
.217
(19.4)
.764
Translucent
White Diffuser
(5.0)
.197
(6.0)
.236
(6.5)
.256
LEDs AT625
AT631 AT632
Spot Illuminated Cap with LED
The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires an external
power source. Single color LEDs are colored in OFF state; bicolor LEDs are translucent white in OFF state. Polarity marks are on the
switch. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the
formula in the Supplement section. Additional lamp detail is shown in the Accessories & Hardware section.
(+)
(-)
1C
1D
1F
CF
Red
Amber
Green
Red/Green
Maximum Forward Current
IFM
25mA
30mA
25mA
30/25mA
Typical Forward Current
IF
20mA
20mA
20mA
20mA
Forward Voltage
VF
2.25V
2.1V
2.2V
2.0/2.2V
Maximum Reverse Voltage
VRM
5V
5V
5V
—
Current Reduction Rate Above 25°C
∆IF
0.33mA/°C
0.43/0.38mA/°C
0.33mA/°C 0.40mA/°C
Ambient Temperature Range
Cap Colors
Available:
A
C
B
F
(13.2) Sq
.520
(4.0)
.157 (2.0)
.079
(5.0)
.197
–25° ~ +70°C
AT480
Square
AT4016
Round
(19.0) Dia
.748
(3.5)
.138
(6.5)
.256
Material:
Polycarbonate
Finish: Glossy
Slides
Not Available
Separately
(+)
(-)
Bicolor
Tactiles
LED factory
assembled in Spot
Illuminated Caps
Single Color
Bicolor LED
with 2 Elements
(5.0)
.197
(4.5)
.177
(5.5)
.217
Cap with Window
(2.0)
(6.0) .079
.236
Factory Assembled LED;
Not Available Separately
Cap for Nonilluminated
E
B
F
C
G
AT484
Square
H
(13.2) Sq
.520
AT4017
Round
(3.5)
.138
(19.0) Dia
.748
(6.5)
.256
(4.5)
.177
(5.5)
.217
Material: Polycarbonate
AT4030
Rectangular
(13.2)
.520
Accessories
A
Indicators
When ordering spot illuminated cap separately, LED color must be specified.
Examples: AT480CA (red LED, black cap); AT4016CFB (red/green bicolored LED, white cap)
Cap Colors
Available:
(19.4)
.764
(5.0)
.197
(6.0)
.236
Cap
No Lamp
Finish: Glossy
www.nkkswitches.com
D
Keylocks
LED Specifications
Single Color LED
with 1 Element
Pushbuttons
JB
Rockers
Cap for Super Bright LEDs
Clear Lens
White Diffuser
Programmable Illuminated PB
D Amber
Rotaries
C Red
Tilt
B White
Touch
A Black
D55
Supplement
Color Codes:
Series LB
Toggles
Standard Size Snap-in Pushbuttons
TYPICAL SWITCH DIMENSIONS
Square
Single & Double Pole
Rockers
(0.5) Typ
.020
Pushbuttons
3
NO
L (+)
(3.2)
.126
D
(21.5)
.846
Latchdown Position
1
4
L (-)
(2.8) Typ
.110
(5.08) Typ
.200
(7.5)
.295
LB15SKW01-12-CJ
(15.8) Sq
.622
5
(1.0)
.039
(17.8) Sq
.701
6
2
COM
(2.54) Typ
.100
Single pole models do not have terminals 4, 5, & 6.
Round
Single & Double Pole
(1.2) x (2.0) Typ
.047 x .079
(1.8)
.071
(0.5) Typ
.020
NC
3
NO
COM
(2.54) Typ
.100
(1.0)
.039
Rotaries
(19.0) Dia
.748
(23.7) Dia
.933
(3.2)
.126
L (+)
6
2
5
1
4
L (-)
(15.8) Sq
.622
(21.7) Dia
.854
(2.8) Typ
.110
(5.08) Typ
.200
(7.5)
.295
(21.5)
.846
Latchdown Position
LB16CKW01-12-CJ
Slides
NC
(13.2) Sq
.520
Keylocks
Programmable Illuminated PB
(1.2) x (2.0) Typ
.047 x .079
(1.8)
.071
Single pole models do not have terminals 4, 5, & 6.
Rectangular
Single & Double Pole
Tactiles
(1.8)
.071
(1.2) x (2.0) Typ
.047 x .079
(0.5) Typ
.020
(13.2)
.520
(17.8)
.701
NC
NO
COM
Tilt
(2.54) Typ
.100
(19.4)
.764
(3.2)
.126
Touch
LB26RGW01-12-CJ
6
5
2
(15.8)
.622
4
1
(5.08) Typ
.200
(22.0)
.866
(7.5)
.295
(22.5)
.886
Latchdown Position
L (+)
L (-)
(1.0)
.039
(24.0)
.945
3
(2.8) Typ
.110
Single pole models do not have terminals 4, 5, & 6.
Indicators
OPTIONAL ACCESSORIES
PCB Adaptors
AT711
Single Pole • Straight PC Terminals
Accessories
(0.3) Typ
.012
NC
NO
COM
Supplement
(0.5)
.020
(15.0)
(4.0)
.591
.157
L
(+)
(-)
NO
COM
(2.54) Typ
.100
(0.74) Typ
.029
Double Pole • Straight PC Terminals
(0.3) Typ
.012
(5.08)
.200
NC
L
AT712
(15.8) Sq
.622
NO
(2.54) Typ
.100
(1.0) Dia Typ
.039
(5.08)
.200
COM
(0.5)
.020
(15.0)
(4.0)
.591
.157
Note: Order adaptors separately.
D56
www.nkkswitches.com
(2.54) Typ
.100
(0.74) Typ
.029
(5.08) Typ
.200
NC
NC
L
(+)
NO
L
(-)
COM
(15.8) Sq
.622
(2.54) Typ
.100
(1.0) Dia Typ
.039
(5.08)
.200
Series LB
Toggles
Standard Size Snap-in Pushbuttons
OPTIONAL ACCESSORIES
(23.5)
.925
(4.3) Typ
.169
(5.2)
.205
End Position
(20.0)
.787
Cutouts for More Than 1 Switch
(19.2)
.756
A
Pushbuttons
AT498
Center
(16.2)
.638
(15.0)
.591
Center Position
Material: Polyamide
(1.19)
.047
(1.19)
.047
(19.2)
.756
Square
A = .752” (19.1mm) x Number of Switches + .051” (1.3mm)
Rectangular
A = .996” (25.3mm) x Number of Switches + .051” (1.3mm)
AT499
Square
Protective Guard
Keylocks
Protective Guard
D
Programmable Illuminated PB
AT497
End
Rockers
Barriers
(10.0)
.394
Material: Polyamide
Cap Height
When
Assembled
(20.0)
.787
(14.0) Sq
.551
(17.9) Sq
.705
(8.0)
.315
Slides
(17.0)
.669
Rotaries
(21.0)
.827
Opens 90°
Closes manually
Protective Guards reduce depth of switch behind panel by .020” (0.5mm).
Tactiles
Spring Loaded Protective Guard
(10.5)
.413
(17.9)
.705
(20.5)
.807
(7.1)
.280
(18.4)
.724
(20.4)
.803
Cap Height
When
Assembled
(7.5)
.295
(14.2)
.559
(17.9)
.705
(16.2) Sq
.638
(20.5)
.807
180°
Accessories
Materials:
Cover: Clear Polycarbonate
Base: Black GFR Polyamide
Coil Spring: Stainless Steel
(10.5)
.413
Indicators
(39.0) Min*
1.535
AT4171
(20.4)
.803 (N)
* Minimum dimension allows opening of cover to 180°
Supplement
(20.4)
.803
(N) = Number of switches
Recommended Panel Thickness:
.039” ~ .106” (1.0mm ~ 2.7mm)
www.nkkswitches.com
Tilt
Opens 180°
Closes automatically
Touch
AT4171
Square
Protective Guard
D57
Series LB
Toggles
Standard Size Snap-in Pushbuttons
OPTIONAL ACCESSORIES
Protective Guard
Rockers
AT4057
Rectangular
Protective Guard
Pushbuttons
Opens 90°
Closes manually
Cap Height
When
Assembled
D
Material: Polyamide
(24.15)
.951
(8.0)
.315
Protective Guards reduce depth of switch behind panel by .020” (0.5mm).
Spring Loaded Protective Guard
AT4172
Rectangular
Protective Guard
(10.5)
.413
(7.1)
.280
(24.6)
.969
Rotaries
(16.2)
.638
(39.0) Min*
1.535
Cap Height
When
Assembled
(26.6)
1.047
(20.4)
.803
(7.5)
.295
180°
Materials:
Cover: Clear Polycarbonate
Base: Black GFR Polyamide
Coil Spring: Stainless Steel
(20.5)
.807
(26.6)
1.047
(26.6)
1.047 (N)
(N) = Number of switches
(24.1)
.949
Opens 180°
Closes automatically
(10.5)
.413
Tactiles
(17.9)
.705
(20.5)
.807
(22.4)
.882
AT4172
Slides
(14.0)
.551
(21.0)
.827
(26.0)
1.024
Keylocks
Programmable Illuminated PB
(10.0)
.394
Recommended Panel Thickness:
.039” ~ .106” (1.0mm ~ 2.7mm)
* Minimum dimension allows opening of cover to 180°
Tilt
Dust Covers
AT4001
Square
AT4011
Rectangular
Indicators
Touch
AT4002
Round
Supplement
Accessories
(21.0) Dia
.827
Cap Height
When
Assembled
(7.3)
.287
(2.5)
.098
(21.8) Dia
.858
Cap Height
When
Assembled
(30.0) Dia
1.181
(16.5)
.650
(16.5)
.650
(15.0) Sq
.591
(2.5)
.098
(7.3)
.287
(24.0)
.945
(22.7)
.894
(24.0) Sq
.945
(30.2)
1.189
Materials: PVC with polyethylene gasket; PVC loses pliability below 0°C (32°F). Dust Covers reduce depth of switch behind panel by .020” (0.5mm).
D58
www.nkkswitches.com
Series LB
Rockers
Toggles
General Specifications
Electrical Capacity (Resistive Load)
Environmental Data
Operating Temperature Range:
Humidity:
Vibration:
Shock:
Sealing:
Installation
Mounting Torque:
Cap Installation Force:
Quick Connect Force:
Soldering Time & Temperature:
Programmable Illuminated PB
Keylocks
Rotaries
Glass fiber reinforced polyamide (UL94V-0)
Nitrile butadiene rubber
Silicone rubber
Silver alloy or copper with gold plating
Silver alloy or copper with gold plating
Liquid crystal polymer (UL94V-0)
Phosphor bronze with silver or gold plating
Brass with silver plating
Slides
Housing:
O-ring:
Inner Seal:
Movable Contact:
Stationary Contacts:
Base:
Switch Terminals:
Lamp Terminals:
D
–25°C through +50°C (–13°F through +122°F) for Illuminated
–25°C through +70°C (–13°F through +158°F) for Nonilluminated
Note: When used with a polyvinyl chloride splash cover, the lowest limit is 0°C (32°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Tactiles
Materials & Finishes
50 milliohms maximum for silver; 100 milliohms maximum for gold
200 megohms minimum @ 500V DC
1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts & case for 1 minute minimum
1,000,000 operations minimum for momentary circuit
200,000 operations minimum for maintained circuit
100,000 operations minimum
5.39N
Nonshorting (break-before-make)
Pretravel .059” (1.5mm); Overtravel .059” (1.5mm); Total Travel .118” (3.0mm)
IP65 of IEC60529 standard (similar to NEMA 4 & 13)
Touch
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Contact Timing:
Travel:
1.96Nm (17.35 lb•in) maximum
3.92N maximum downward force on cap
52.95N maximum downward force on connector
Manual Soldering: See Profile A in Supplement section.
Indicators
Other Ratings
Pushbuttons
Power Level (silver):
3A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC
Logic Level (gold):
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Tilt
Standard Size Panel Seal Pushbuttons
Standards & Certifications
www.nkkswitches.com
Supplement
Accessories
Flammability Standards:
UL94V-0 housing & base
UL:
File No. E44145 - Recognized only when ordered with marking on switch.
Add “/U” or “/CUL” before first dash in part number to order UL recognized switch.
All models recognized at 3A @ 125V or 250V AC or 0.4VA @ 28V AC/DC maximum.
CSA:
File No. 023535_0_000 - Certified only when ordered with marking on switch.
Add “/C” before first dash in part number to order CSA certified switch.
All models certified at 3A @ 125V or 250V AC or 0.4VA @ 28V AC/DC maximum.
D59
Series LB
Toggles
Standard Size Panel Seal Pushbuttons
TYPICAL SWITCH
1
Poles
D
1
SPDT
2
DPDT
6
W
Circuits
5
ON
W
(ON)
Round
( ) = Momentary
6
ON
K
Shape
W01
Housing
K
Black
G
Gray
ON
Alternate Action
with Latchdown
Contacts & Terminals
Rotaries
Keylocks
Programmable Illuminated PB
Pushbuttons
Rockers
LB
W01
Silver Contacts
Rated 3A @ 125/250V AC
Solder Lug/Quick Connect Terminals
G01
Gold Contacts
Rated 0.4VA @ 28V AC/DC
Solder Lug/Quick Connect Terminals
IMPORTANT:
Tactiles
Slides
Switches are supplied without UL, cULus & CSA marking unless specified.
UL, cULus & CSA recognized only when ordered with marking on the switch.
Specific models, ratings, & ordering instructions are noted on the General
Specifications page.
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
Tilt
LB16WKW01-5C12-JC
Touch
Red, 12-volt, Bright LED with Resistor
Indicators
Round Shape
Clear Cap with Red Diffuser
SPDT ON-ON Circuit
Black Housing
Supplement
Accessories
Silver Contacts
Rated 3A @ 125/250V AC;
Solder Lug/Quick Connect Terminals
D60
www.nkkswitches.com
Series LB
Toggles
Standard Size Panel Seal Pushbuttons
ORDERING EXAMPLE
Incandescent Lamp Used with Solid Cap
Solid Cap: Lens/Filter Colors
05
5-volt
BJ
White/Clear
12
12-volt
CJ
Red/Clear
EJ
Yellow/Clear
FJ
Green/Clear
GJ
Blue/Clear
Nonilluminated
Incandescent or Neon Used with Insert Cap
Insert Cap: Lens/Filter Colors
01
110-volt Neon
JB
Clear/White
05
5-volt Incandescent
JC
Clear/Red
12
12-volt Incandescent
No
Code
Nonilluminated
JE
Clear/Yellow
* JF
Clear/Green
* JG
Clear/Blue
Rotaries
No
Code
D
Red
5D
Amber
5F
Green
JB
Clear/White
No Resistor
JC
Clear/Red
05
5-volt
JD
Clear/Amber
12
12-volt
JF
Clear/Green
24
24-volt
No Code
Touch
5C
Resistor
LED Cap: Lens/Diffuser Colors
Tilt
Colors
Tactiles
*JF & JG not suitable with neon.
Bright LED Used with LED Cap
Programmable Illuminated PB
Cap Types & Colors
Keylocks
Lamps
Pushbuttons
Rockers
JC
Slides
5C 12
Green
6G
Blue
Clear/White
Accessories
6F
LED Cap: Lens/Diffuser Colors
JB
Supplement
White
Indicators
Super Bright LED Used with LED Cap
6B
www.nkkswitches.com
D61
Series LB
Toggles
Standard Size Panel Seal Pushbuttons
POLES & CIRCUITS
Rockers
Plunger Position
( ) = Momentary
D
Normal
Down
Normal
Down
LB15
*LB16
ON
ON
(ON)
ON
1-3
1-2
SPDT
DP
LB25
*LB26
ON
ON
(ON)
ON
1-3 4-6
1-2 4-5
DPDT
3
1
3
1
COM
NC
2
COM
NC 2
NO
6
L (+)
(-) L
L (+)
(-) L
NO
4
COM
NC
5
NO
* When in latchdown position for the alternate circuit, cap position is .039” (1.0mm) above the built-in bezel.
SHAPE & PANEL CUTOUT
W
.866” (22.0mm)
Round
(1.7)
.067
Recommended Panel Thickness:
.039” ~ .157” (1.0mm ~ 4.0mm)
(10.5)
.413
Recommended Panel Thickness with Splash Cover:
.039” ~ .138” (1.0mm ~ 3.5mm)
Rotaries
Overtightening the mounting nut AT074
may damage the switch housing.
(22.0) Dia
.866
HOUSING
K
Housing Colors Available:
G
Black
Gray
CONTACT MATERIALS, RATINGS & TERMINALS
Tactiles
Slides
Notes: Switch is marked with NC, NO, COM, L+, L–.
Lamp circuit is isolated and requires
external power source.
Model
W01
Silver Contacts
Power Level
3A @ 125V AC & 250V AC
Solder Lug/Quick Connect
Epoxy
Seal
Tilt
Touch
Throw & Switch/Lamp Schematics
SP
Keylocks
Programmable Illuminated PB
Pushbuttons
Pole
Connected Terminals
G01
Gold Contacts
Logic Level
0.4VA max. @ 28V AC/DC max.
(2.0)
.079
Optional PCB adaptors AT711
& AT712 available; illustrated
in previous snap-in subsection.
Complete explanation of operating range in Supplement section.
(7.5)
.295
(2.8)
.110
(1.2)
.047
Thk = (0.5)
.020
AT607 & AT607N
Accessories
Indicators
INCANDESCENT & NEON LAMP CODES & SPECIFICATIONS
AT607 Incandescent 5-volt or
12-volt; AT607N Neon 110-volt
Supplement
D62
12
01 *
Voltage
V
5V AC
12V AC
110V AC
Current
I
115mA
60mA
1.5mA
Endurance
T-1 Bi-pin
05
Avg. Hours
Ambient Temp. Range
10,000
–25°C ~ +50°C
www.nkkswitches.com
10,000
The electrical specifications shown are
determined at a basic temperature of
25°C. Lamp circuit is isolated and
requires external power source.
* Recommended Resistors for Neon:
33K ohms for 110V AC;
100K ohms for 220V AC
Series LB
Toggles
Standard Size Panel Seal Pushbuttons
LED COLORS & SPECIFICATIONS
Rockers
The electrical specifications shown are determined at a basic temperature of 25°C.
LED circuit is isolated and requires external power source. Polarity marks are on the switch.
If the source voltage exceeds the rated voltage, a ballast resistor is required.
The resistor value can be calculated by using the formula in the Supplement section.
Additional lamp detail is shown in the Accessories & Hardware section.
(-)
Green
5C
5D
5F
No Code
Red
Amber
Green
Maximum Forward Current
IFM
30mA
30mA
30mA
Typical Forward Current
IF
20mA
20mA
20mA
Forward Voltage
VF
1.9V
2.0V
2.1V
Maximum Reverse Voltage
VRM
5V
5V
5V
Current Reduction Rate Above 25°C
∆IF
D
0.42mA/°C
Ambient Temperature Range
T-1 ⁄ Bi-pin
12
No Resistor
–25° ~ +50°C
Keylocks
(+)
Amber
Bright LED with Resistor
Green
5C
5D
5F
Resistor Codes
05
12
24
Maximum Forward Current
IFM
—
—
—
Typical Forward Current
IF
52mA
26mA
13mA
Forward Voltage
VF
5V
12V
24V
Maximum Reverse Voltage
VRM
4V
8V
16V
Current Reduction Rate Above 25°C
∆IF
0.50mA/°C
Ambient Temperature Range
T-1 Bi-pin
AT627
5-volt
4-element (+)
with Resistor
(-)
Rotaries
Amber
Slides
Color Codes:
Red
–25° ~ +50°C
AT627
12-volt
4-element (+)
with Resistor
(-)
Tactiles
AT627
with Resistor
Programmable Illuminated PB
Color Codes
LEDs are colored
in OFF state.
Red
AT627
24-volt
(+)
4-element
with Resistor
(-)
Tilt
AT635
Pushbuttons
Bright LED without Resistor
ATTENTION
6G
Color
White
Green
Blue
Maximum Forward Current
IFM
30mA
30mA
30mA
Typical Forward Current
IF
20mA
20mA
20mA
Forward Voltage
VF
3.3V
3.3V
3.3V
(-)
Maximum Reverse Voltage
VRM
7V
7V
7V
Current Reduction Rate Above 25°C
∆IF
0.40mA/°C
0.40mA/°C
0.40mA/°C
T-1 Bi-pin
Ambient Temperature Range
Indicators
6F
–25° ~ +50°C
Supplement
(+)
No Code
6B
ELECTROSTATIC
SENSITIVE DEVICES
Accessories
AT625G Blue
AT631B White
AT632F Green
Touch
Super Bright Single Element LED
No Lamp
www.nkkswitches.com
D63
Toggles
Series LB
CAP TYPES & COLOR COMBINATIONS
Color Codes:
Rockers
Pushbuttons
Lens/Filter
Colors Available:
D
C Red
D Amber
E Yellow
F Green
G Blue
J Clear
BJ
FJ
CJ
GJ
(19.0) Dia
.748
AT4054
(5.1)
.201
Translucent
Colored Lens
EJ
Material: Polycarbonate
Transparent
Clear Filter
Lamp
AT607
Finish: Glossy
Insert Cap for Incandescent or Neon Lamp & Nonilluminated
Lens/Filter
Colors Available:
Keylocks
Programmable Illuminated PB
B White
Solid Cap for Incandescent Lamp & Nonilluminated
Rotaries
Slides
Standard Size Panel Seal Pushbuttons
JB
JF
JC
JG
(19.0) Dia
.748
Lamp
AT607
AT4055
(5.1)
.201
JE
JF and JG not suitable
with neon lamp.
Transparent
Clear Lens
Material: Polycarbonate
Translucent
Colored Filter
Lamp
AT607N
Translucent
Colored Diffuser
Bright LED
AT635
Translucent
Colored Diffuser
Bright LED
AT627
Finish: Glossy
Lens/Diffuser
Colors Available:
JB
(19.0) Dia
.748
AT4179
JC
Tilt
Tactiles
Cap for Bright LED without Resistor
(5.1)
.201
JD
Transparent
Clear Lens
Touch
JF
Material: Polycarbonate
Finish: Glossy
Lens/Diffuser
Colors Available:
JB
Accessories
Indicators
Cap for Bright LED with Resistor
JC
(19.0) Dia
.748
AT4165
(5.1)
.201
Transparent
Clear Lens
Supplement
JD
JF
D64
Material: Polycarbonate
www.nkkswitches.com
Finish: Glossy
Series LB
Toggles
Standard Size Panel Seal Pushbuttons
CAP TYPES & COLOR COMBINATIONS
(5.1)
.201
Transparent
Clear Lens
Translucent
Colored Diffuser
LEDs
AT625
AT631
AT632
TYPICAL SWITCH DIMENSIONS
Single & Double Pole
(5.5)
.217
Panel Seal
(1.2) x (2.0) Typ
.047 x .079
M22 P1
3
COM
1
6
5
2
(2.54) Typ
.100
(1.8)
.071
(1.0)
.039
(3.2)
.126
L (+)
(15.8) Sq
.622
4
L (-)
Rotaries
NC
NO
Keyway
(12.0)
.472
(21.5)
.846
Latchdown Position
(2.8) Typ
.110
(7.5)
.295
(5.08) Typ
.200
LB25WKW01-12-JC
Single pole models do not have terminals 4, 5, & 6.
Tactiles
OPTIONAL ACCESSORIES
AT9410 Splash Cover for Panel Seal
D
Keylocks
(0.5) Typ
.020
(19.0) Dia
.748
(25.0) Dia
.984
Pushbuttons
AT4131
Programmable Illuminated PB
Material:
Polycarbonate
Finish: Glossy
(19.0) Dia
.748
Slides
Clear Lens
White Diffuser
Lid
Materials:
Lid: PVC (loses pliability below 0°C/32°F)
Base: Polyethylene
O-ring: NBR
Tilt
Base
O-ring Supplied with
Panel Seal Switch
O-ring Supplied with
AT9410 Splash Cover
Indicators
Touch
Recommended Panel Thickness:
.039” ~ .138” (1.0mm ~ 3.5mm)
Accessories
(21.0) Dia
.827
(10.6)
.417
(31.3) Dia
1.232
(7.8)
.307
(3.0)
.118
(1.6)
.063
(23.0) Dia
.906
www.nkkswitches.com
(22.0) Dia
.866
(31.3) Dia
1.232
(0.5)
.020
D65
Supplement
JB
Rockers
Cap for Super Bright LEDs
Series LB
Toggles
Standard Size Pushbuttons
ASSEMBLY INSTRUCTIONS
Panel Seal Models
Pushbuttons
Align projections on lamp
with grooves (B) in holder
when inserting lamp. To
correctly join the lamp
holder and cap base,
match the cut corners (A).
D
For panel seal models,
Bright LED must first be
inserted into the lamp
socket which is built into
the switch. The cap can
then be placed on the
switch.
Bright & Super Bright LEDs
AT625, AT631, AT632,
AT635
Snap-in Models
For snap-in models,
Bright LED must be
inserted into the cap
first. Align cut corners
(C) when
inserting
the LED.
Align D-flat on LED with flat (B) in
holder when inserting the LED.
To correctly join the lamp holder and
cap base, match the cut corners (A).
ATTENTION
ELECTROSTATIC
SENSITIVE DEVICES
B
A
B
A
LED
B
LED
C
D Flat
Switch & Cap Assembly
Keylocks
Programmable Illuminated PB
Bright LED AT627
Incandescent & Neon Lamps
AT607 & AT607N
5
Rockers
Lamp Installation & LED Orientation
C
Rotaries
Cut Corner
Round & Rectangular
Match clip on cap assembly with receptacle inside
switch. Lamp terminals will then be aligned correctly
with lamp socket.
N
.C
.
Rubber Seal
Slides
N .O .
3 25
A
3
K
S
5 C
-1 5V A C
LBA 12 0V A
N
.C
.
Projection
Projection
Notch
Tilt
Tactiles
C
Panel Seal
With Lamps AT607, AT607N, and
LEDs AT614, AT625, AT631, AT632:
Match projection on cap assembly with
notch inside switch. Lamp terminals
will then be aligned correctly with lamp
socket.
Square
Match projection (C) on cap
assembly with groove (C)
inside switch. Lamp terminals
will then be aligned correctly
with lamp socket.
Touch
Installation & Maintenance
Snap-in Mount
Panel Seal
Bushing Mount
Lamp Replacement
Supplement
Accessories
Indicators
Bezel
Snap-in clip holds all switches firmly
in place.
To mount round
switch, match
the antirotation Projection
projection on
switch with
guide cut in
Panel
panel. Snap
into panel
cutout.
D66
Insert switch from the
front of the panel with
the o-ring between the
built-in bezel and the
panel. Install mounting
nut AT075 (supplied with
switch) from the rear of
the panel.
Overtightening mounting
nut may damage the
switch housing.
www.nkkswitches.com
O-ring
Panel
Actuator must be in UP position.
Pull off cap with cap extractor
AT109.
Replace lamp and reassemble as
shown above.
Mounting Nut
AT109
Cap Extractor
AT112
Socket Wrench
Series LB
Toggles
Standard Size Pushbuttons
LEGENDS
Rockers
NKK Switches can provide custom legends for caps. Contact factory for more information.
Suggested Printable Area for Lens
Epoxy based ink is recommended.
(0.76) Typ
.030
(13.2)
.520
T
AR
ST
(11.68)
.460
(11.68) Sq
.460
(13.2) Sq
.520
(17.48) Dia
.688
(19.0) Dia
.748
(0.76) Typ
.030
(0.76) Typ
.030
(17.88)
.704
(0.76) Typ
.030
(19.4)
.764
Keylocks
Shaded areas are printable areas.
Suggested Printable Area for Film Insert
Rotaries
Recommended Print Method: Laser Print or Screen Print with Epoxy based ink
Film Insert: Clear Polyester, 4 mil max. thickness
R = (0.6)
.024
(0.76) Typ
.030
(14.66)
.577
Film
Insert
Slides
Lens
(10.08) (11.6)
.397 .457
(0.76) Typ
.030
(16.28)
.641
(17.8)
.701
(0.76) Typ
.030
Tilt
(15.88) Dia
.625
(17.4) Dia
.685
Indicators
Touch
Shaded areas are printable areas.
Accessories
(0.76) Typ
.030
Supplement
(10.08) Sq
.397
(11.6) Sq
.457
Tactiles
ON
Filter or
Diffuser
D
Programmable Illuminated PB
Pushbuttons
Recommended Methods: Laser Etch on clear lens, Screen Print, or Pad Print on lens.
www.nkkswitches.com
D67
Similar pages