Coilcraft LPS4018-154MR Shielded power inductor Datasheet

Document 435-1
Shielded Power Inductors – LPS4018
• Very low DCR; excellent current handling
• 4.0 × 4.0 mm footprint; less than 1.8 mm tall
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Environmental RoHS compliant, halogen free
Terminations RoHS compliant matte tin over nickel over silver.
Other terminations available at additional cost.
Weight 54 – 100 mg
Ambient temperature –40°C to +85°C with (40°C rise) Irms current.
Maximum part temperature +125°C (ambient + temp rise). Derating.
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 1000/7″ reel; 3500/13″ reel Plastic tape: 12 mm wide,
0.23 mm thick, 8 mm pocket spacing, 1.9 mm pocket depth
Recommended pick and place nozzle OD: 4 mm; ID: ≤ 2 mm
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Part number1
Isat (A)5 Irms (A)6
DCR
SRF
3
4
max
typ 10% 20% 30% 20°C 40°C
(Ohms) (MHz) drop drop drop rise rise
Inductance2
(µH)
LPS4018-561MR_ 0.56 ±20% 0.033
LPS4018-102NR_ 1.0 ±30% 0.042
LPS4018-222MR_ 2.2 ±20% 0.070
LPS4018-332MR_ 3.3 ±20% 0.080
LPS4018-472MR_ 4.7 ±20% 0.125
LPS4018-682MR_ 6.8 ±20% 0.150
LPS4018-103MR_ 10 ±20%
0.200
LPS4018-153MR_ 15 ±20%
0.260
LPS4018-183MR_ 18 ±20%
0.270
LPS4018-223MR_ 22 ±20%
0.360
LPS4018-333MR_ 33 ±20%
0.420
LPS4018-473MR_ 47 ±20%
0.650
LPS4018-683MR_ 68 ±20%
0.950
LPS4018-104MR_ 100 ±20%
1.40
LPS4018-124MR_ 120 ±20%
1.60
LPS4018-154MR_ 150 ±20%
2.00
LPS4018-184MR_ 180 ±20%
2.50
LPS4018-224MR_ 220 ±20%
3.70
LPS4018-334MR_ 330 ±20%
5.90
LPS4018-474MR_ 470 ±20%
7.80
LPS4018-564MR_ 560 ±20% 10.0
LPS4018-684MR_ 680 ±20% 11.5
LPS4018-824MR_ 820 ±20% 14.0
LPS4018-105MR_ 1000 ±20% 18.0
250
180
90
75
65
50
40
32
27
26
20
16
13
10
9.0
8.0
7.5
6.5
5.5
4.5
4.0
3.5
2.9
2.8
4.8
3.8
2.7
1.9
1.8
1.2
1.1
0.86
0.78
0.74
0.58
0.51
0.41
0.34
0.31
0.27
0.24
0.21
0.18
0.14
0.13
0.12
0.11
0.10
5.2
3.9
2.8
2.0
1.9
1.3
1.2
0.91
0.83
0.80
0.64
0.55
0.45
0.36
0.33
0.29
0.26
0.225
0.19
0.16
0.14
0.13
0.12
0.11
5.3
4.0
2.9
2.0
1.9
1.3
1.3
0.94
0.85
0.83
0.68
0.56
0.46
0.37
0.34
0.30
0.27
0.235
0.20
0.17
0.15
0.14
0.13
0.11
1.9
1.8
1.5
1.4
1.3
1.0
0.90
0.80
0.70
0.65
0.55
0.45
0.40
0.35
0.30
0.28
0.26
0.20
0.17
0.15
0.14
0.12
0.10
0.098
2.8
2.5
2.0
1.9
1.8
1.5
1.25
1.12
1.00
0.90
0.80
0.68
0.56
0.50
0.45
0.40
0.36
0.30
0.23
0.20
0.18
0.16
0.14
0.125
Coilcraft Designer’s Kit C392 contains samples of 0.80 µH to 33 µH parts (3 each)
from LPS3008, LPS3010 and LPS3015. Kit C401 contains samples of 0.56 µH to
33 µH parts (3 each) from LPS4012 and LPS4018. Kit C402 contains samples of 220
µH to 3300 µH parts (3 each) from all five series. For details of kit contents and to
order, contact Coilcraft or visit http://order.coilcraft.com.
1. Please specify termination and packaging codes:
LPS4018-223MRC
Termination: R = RoHS compliant matte tin over
nickel over silver.
Special order, added cost:
Q = RoHS tin-silver-copper (95.5/4/0.5)
or P = non-RoHS tin-lead (63/37).
Packaging: C = 7″ machine-ready reel. EIA-481
embossed plastic tape (1000 parts
per full reel).
B = Less than full reel. In tape, but not
machine ready.
To have a leader and trailer added
($25 charge), use code letter C
instead.
D = 13″ machine-ready reel. EIA-481
embossed plastic tape. Factory
order only, not stocked (3500 parts
per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms using an
Agilent/HP 4192A. Inductance at 1 MHz is the same
for parts with SRF ≥10 MHz.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using Agilent/HP 8753ES or equivalent.
5. DC current at 25°C that causes the specified inductance drop from its value without current.
Click for temperature derating information.
6. Current that causes the specified temperature rise from
25°C ambient. This information is for reference only and
does not represent absolute maximum ratings.
Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Document 435-1
Revised 09/02/15
Document 435-2
Shielded SMT Power Inductors – LPS4018 Series
Typical L vs Frequency
Typical L vs Current
10000
10000
2200 µH
680 µH
100
22 µH
10
4.7 µH
1 µH
1
0.1
0.01
0.1
100
22 µH
10
4.7 µH
1 µH
10
1
Frequency (MHz)
0.1
0.01
0.1
Current (A)
1
10
Packaging 1000/7″ reel; 3500/13″ reel Plastic tape: 12 mm wide,
0.23 mm thick, 8 mm pocket spacing, 1.9 mm pocket depth
0.1535 ±0.003*
3,90 ±0,076
NOTE NEW PART ORIENTATION Parts are rotated 90° in the
packaging tape compared to previous versions of this product.
Winding
direction
NEW
0.0669 ±0.004*
1,70 ±0,10
OLD
123
Internal
code
123
123
Dash
number
680 µH
1
0.1535 ±0.003*
3,90 ±0,076
XXX X
2200 µH
1000
Inductance (µH)
Inductance (µH)
1000
123
123
123
Recommended
Land Pattern
0.105
2,66
0.059
1,50
0.110 0.045
2,79 1,15
0.060
1,52
are of the case not including
* Dimensions
the termination. For maximum overall
dimensions including the termination, add
0.005 in / 0,13 mm.
For optional tin-lead and tin-silver-copper
terminations, dimensions are for the
mounted part. Dimensions before mounting
can be an additional 0.005 inch / 0,13 mm).
0.0305
0,775
0.153
3,89
0.129
3,28
0.173
4,40
Dimensions are in
inches
mm
Document 435-2
Revised 09/02/15
Similar pages