Fujitsu MB95F284L 8-bit microcontrollers mb95350l sery Datasheet

FUJITSU SEMICONDUCTOR
INTRODUCTION SHEET
NP07-12631-1E
8-bit Microcontrollers
MB95350L Series
The MB95350L is a series of general-purpose, single-chip microcontrollers.
In addition to a compact instruction set, the microcontrollers of this series
contain a variety of peripheral resources for example 2 channels I2C.
This can be used for the Security sensors, Toys, Heater detector applications
which need more communication ports application etc.
■ FEATURES
 F2MC-8FX CPU
■PRODUCT LINEUP
Part number
Parameter
Instruction set optimized for controllers
MB95F
352E
MB95F
353E
Type
 Clock
Maximum clock frequency:16.25MHz
 Timer
8/16-bit composite timer:2 channels
Time-base timer:1 channels
 UART/SIO
1 channel(alternative selection between I2C and UART/SIO)
MB95F
282L
MB95F
283L
MB95F
284L
Flash memory product
ROM
(Byte)
8K
RAM
(Byte)
240
Low-voltage
detection
reset
MB95F
354E
12K
20K
496
8K
12K
240
Yes
20K
496
No
 I2C
1 channel
[+ 1 channel(alternative selection between I2C and UART/SIO)]
 LIN/UART:1 channel
 External interrupt:6 channels
- Interrupt by edge detection
- Can be used to wake up the device from different
low power consumption (standby) modes
 8/10-bit A/D converter:6 channels
 Low power consumption (standby) modes
Stop mode
Sleep mode
Watch mode
Time-base timer mode
 I/O port
MB95F352E/F353E/F354E:22
MB95F352L/F353L/F354L:21
 On-chip debug
- 1-wire serial control
- Serial writing supported (asynchronous mode)
■ORDERING INFORMATION
Product name
Package
Remarks
MB95F352EPF
MB95F352LPF
MB95F353EPF
MB95F353LPF
MB95F354EPF
MB95F354LPF
Plastic・SOP,24-pins
(LCC-24P-M34)
7.50mm×15.34mm,1.27mm pitch
-
MB95F352EPFT
MB95F352LPFT
MB95F353EPFT
MB95F353LPFT
MB95F354EPFT
MB95F354LPFT
Plastic・TSSOP,24-pins
(FPT-24P-M10)
4.40mm×7.80mm,0.65mm pitch
-
MB95F352EWQN
MB95F352LWQN
MB95F353EWQN
MB95F353LWQN
MB95F354EWQN
MB95F354LWQN
Plastic・QFN,32-pins
(LCC-32P-M19)
5.00mm□,0.50mm pitch
-
■PACKAGE EXAMPLE OF REFERENCE
 Hardware/software watchdog timer
 Low-voltage detection reset circuit
MB95F352E/F353E/F354E
 Clock supervisor counter
 Dual operation Flash memory
 Flash memory security function
 Power supply:1.8~3.6V
*The range of the power supply voltage is different
according to the operating frequency and the operating
temperature.
May, 2010
1/2
Copyright©2010 FUJITSU SEMICONDUCTOR LIMITED All rights reserved
Plastic ・ TSSOP, 24-pins
(FPT-24P-M10)
MB95350L Series
PRELIMINARY
■ BLOCK DIAGRAM
F2MC-8FX CPU
PF2/RST*2
Reset with LVD
Flash with security function
PF1/X1*2
PF0/X0*2
Oscillator
circuit
PG2/X1A*2
CR
oscillator
RAM (496/240 bytes)
PG1/X0A*2
Interrupt controller
(P04/HCLK1)
Clock control
(P05*3/HCLK2)
(P05*3/TO00)
(P12/DBG*1)
On-chip debug
(P06*3/TO01)
8/16-bit composite timer (0)
External interrupt
P02/INT02 to P07/INT07
Internal bus
P12*1/EC0, (P04/EC0)
Wild register
P62*3/TO10
P63*3/TO11
8/16-bit composite timer (1)
P64/EC1
8/10-bit A/D converter
(P00/AN00 to P05/AN05)
P14*1/SDA0
I2C (0)
P15*1/SCL0
(P16/SDA1)
I2C (1)
(P17/SCL1)
(P02/SCK)
PG0/UCK
LIN-UART
(P03/SOT)
UART/SIO
P16/UO
(P04/SIN)
P17/UI
Por t
Por t
Vcc
*1: P12, P14 and P15 are N-ch open drain pins.
Vss
*2: Software option
*3: P05, P06, P62 and P63 are high-current ports.
Note: Pins in parentheses indicate that functions of those pins are shared among different resources.
■ SUPPORT TOOL
 HARDWARE
Name
BGM adapter
PC cable
Evaluation board
Part Number
MB2146-08-E
USB cable
MB2146-460-E
Remarks
F2MC-8FX MB95200 series in common
Attached to MB2146-08-E, 1.0m
-
 SOFTWARE
Software
SOFTUNE V3 Professional Pack
Part Number
SP36503Z008-P01
Operating System
Windows2000/XP/Vista
 FLASH MICROCONTROLLER PROGRAMMER
Name
Parallel programmer
Serial on board programmer
Remarks
Made by Flash Support Group, etc. (Under contemplation)
FUJITSU FLASH MCU Programmer
NP07-12631-1E
May, 2010
2/2
Copyright©2010 FUJITSU SEMICONDUCTOR LIMITED All rights reserved
Similar pages