Kemet C062H105J5R5GA7061 Radial through-hole multilayer ceramic capacitor Datasheet

Radial Through-Hole Multilayer Ceramic Capacitors
High Temperature 200°C, Radial, Molded, X7R Dielectric,
50 – 200 VDC (Industrial Grade)
Overview
KEMET’s High Temperature 200ºC epoxy molded radial
through-hole ceramic capacitors in X7R dielectric feature
a robust and proprietary dielectric system that offers
industry-leading performance in extreme high pressure
and high temperature environments up to 200°C. These
capacitors are designed specifically to withstand the
severe shock and vibration conditions associated with
deep-well and horizontal drilling activities and are well
suited for use in aerospace engine compartments,
geophysical probes, hybrid and electric automotive motor
drives and defense applications.
These epoxy molded radial through-hole ceramic capacitors
in X7R dielectric achieve high dielectric breakdown,
low leakage current and minimal parametric shift while
maintaining predictable performance characteristics with
respect to variations in temperature, applied voltage and
time. These devices are suited for bypass and decoupling
applications or for frequency discriminating circuits where Q
and stability of capacitance characteristics are not critical.
Capacitance change is limited to ±15% from −55°C to +125°C
and +15%/−55% at +200°C.
As high temperature electronic module complexity
increases, the size reduction of components becomes
more and more critical. These devices are significantly
smaller by volume than most competitor radial molded
capacitors, allowing for downsizing and replacement
opportunities of larger high temperature precious metal
electrode (PME) and base metal electrode (BME) dielectric
system devices. They feature gold-plated lead wires
for temperature resistance and an epoxy molded case for
environmental protection and mechanical durability.
Click image above for interactive 3D content
Open PDF in Adobe Reader for full functionality
Ordering Information
C
Ceramic
062
H
Style/ Specification/
Size
Series
052
062
H=
High Temp
200ºC
105
K
Capacitance
Code (pF)
Capacitance
Tolerance1
Two significant digits
and number of zeros
Use 9 for 1.0 – 9.9 pF
ex. 2.2 pF = 229
J = ±5%
K = ±10%
M = ±20%
5
R
5
Rated
Voltage Dielectric Design
(VDC)
5 = 50
R=
5=
1 = 100
X7R
Multilayer
2 = 200
G
A
7303
Lead
Finish2
Failure
Rate
Packaging
C-Spec3
G=
Gold (Au)
A=
N/A
Blank = Bulk Bag
T250 = 250 pcs/
12" Reel
T500 = 500 pcs/
12" Reel
T1K0 = 1,000 pcs/
12" Reel
7301 = Full Reel Qty/
12" Reel
7303 = Full Reel Qty/
12" Reel
7061 = Bulk Tray
Additional capacitance tolerance offerings may be available. Contact KEMET for details.
Wire lead materials and finishes: Alternative lead materials and finishes may be available. Contact KEMET for details.
3
Default packaging for this product series is "Bulk Bag". KEMET will assume "Bulk Bag" packaging is required when the 15th thru 18th character positions are
left blank.
3
C-Spec 7301 can only be used when ordering 052 style/size.
3
C-Spec 7303 can only be used when ordering 062 style/size.
1
2
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1074_HT_X7R_RADIAL_MOLDED • 8/10/2016
1
Radial Through-Hole Multilayer Ceramic Capacitors
High Temperature 200°C, Radial, Molded, X7R Dielectric, 50 – 200 VDC (Industrial Grade)
Dimensions – Inches (Millimeters)
C052H
C062H
L
0.045
(1.143)
Maximum
T
L
T
H
H
LL
LL
LD
LD
S
Series
S
S
Lead Spacing
L
Length
H
Height
T
Thickness
LD
Lead Diameter
LL
Lead Length
Minimum
0.20±0.015
(5.08±0.38)
0.19±0.01
(4.83±0.25)
0.29±0.01
(7.37±0.25)
0.19±0.01
(4.83±0.25)
0.29±0.01
(7.37±0.25)
0.09±0.01
(2.29±0.25)
0.09±0.01
(2.29±0.25)
0.025+0.004/−0.002
(0.635+0.102/−0.051)
1.25 (31.75)
C052H
C062H
Benefits
• Operating temperature range of −55°C to +200°C
• X7R temperature stable dielectric
• High shock and vibration capability
• Radial through-hole form factor
• Gold (Au) plated wire lead finish
• Base metal electrode (BME) and precious metal electrode
(PME) dielectric systems.
• RoHS and REACH compliant (most select values)
• Military designation styles CK/CKR05 and CK/CKR06
• Molded case
• High breakdown voltage strength
• DC voltage ratings of 50 V, 100 V and 200 V
• Capacitance offerings ranging from 1,000 pF to 1.0 μF
• Available capacitance tolerances of ±5%, ±10% and ±20%
• Low ESR and ESL
• Predictable performance characteristics with respect to
variations in temperature, applied voltage and time
• Non-polar device, minimizing installation concerns
• Encapsulation meets flammability standard UL 94V–0
• Halogen-free
Applications
Typical applications include decoupling, bypass, smoothing circuits, DC/DC converters, power supplies (input/output filters),
noise reduction (piezoelectric/mechanical), circuits with a direct battery or power source connection, critical and safety
relevant circuits without (integrated) current limitation and any application that is subject to extreme environments such as
high shock and vibration, high temperature, high levels of board flexure and/or temperature cycling. Markets include military,
industrial, aerospace, and automotive.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1074_HT_X7R_RADIAL_MOLDED • 8/10/2016
2
Radial Through-Hole Multilayer Ceramic Capacitors
High Temperature 200°C, Radial, Molded, X7R Dielectric, 50 – 200 VDC (Industrial Grade)
Qualification
These devices are subject to internal qualification. Details regarding test methods and conditions are referenced in Table 2,
Performance & Reliability.
Environmental Compliance
RoHS compliance is dependent upon series and rated capacitance value.
1
Series
Rated
Capacitance
RoHS
Compliant
RoHS Exemption
Code1
Halogen Free
C052H
All
Yes
7(a)
Yes
C062H
< 0.27µF
Yes
7(a)
Yes
C062H
≥ 0.27µF
No
n/a
Yes
7(a): Lead in high melting temperature type solders
Electrical Parameters/Characteristics
Item
Parameters/Characteristics
Operating Temperature Range
Capacitance Change with Reference to
+25°C and 0 VDC Applied (TCC)
Capacitance Change with Reference to
+25°C and 100% Rated VDC Applied
Aging Rate (Maximum % Cap Loss/Decade Hour)
Dielectric Withstanding Voltage
Dissipation Factor (DF) Maximum Limit at 25ºC
Insulation Resistance (IR) Limit at 25°C
−55°C to +200°C
±15% (−55°C to +125°C), +15%/−55% (200°C)
+15%/−30% (−55°C to +125°C), +15%/−60% (200°C)
3%
250% of rated voltage
(5±1 seconds and charge/discharge not exceeding 50 mA at 25°C)
2.50%
1,000 MΩ microfarads or 100 GΩ
(Rated voltage applied for 120±5 seconds)
Regarding aging rate: Capacitance measurements (including tolerance) are indexed to a referee time of 1,000 hours.
To obtain IR limit, divide MΩ-µF value by the capacitance and compare to GΩ limit. Select the lower of the two limits.
Capacitance and dissipation factor (DF) measured under the following conditions:
1 kHz ±50 Hz and 1.0 ±0.2 Vrms if capacitance ≤ 10 µF
120 Hz ±10 Hz and 0.5 ±0.1 Vrms if capacitance > 10 µF
Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 and Agilent E4980 have a feature known
as Automatic Level Control (ALC). The ALC feature should be switched to "ON."
Post Environmental Limits
High Temperature Life, Biased Humidity, Moisture Resistance
Dielectric
X7R
Rated DC Voltage Capacitance Value
> 25
All
DF (%)
Capacitance Shift
IR
3.0
±20%
10% of Initial Limit
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1074_HT_X7R_RADIAL_MOLDED • 8/10/2016
3
Radial Through-Hole Multilayer Ceramic Capacitors
High Temperature 200°C, Radial, Molded, X7R Dielectric, 50 – 200 VDC (Industrial Grade)
Table 1A – C052 Style/Size (0.20" Lead Spacing), Capacitance Range Waterfall
C052 Style/Size (0.20" Lead Spacing)
Rated Voltage (VDC)
50
100
200
Voltage Code
5
1
2
Capacitance
Tolerance
Capacitance
1,000 pF
1,200 pF
1,500 pF
1,800 pF
2,200 pF
2,700 pF
3,300 pF
3,900 pF
4,700 pF
5,600 pF
6,800 pF
8,200 pF
0.01 µF
0.012 µF
0.015 µF
0.018 µF
0.022 µF
0.027 µF
0.033 µF
0.039 µF
0.047 µF
0.056 µF
0.068 µF
0.082 µF
0.1 µF
Capacitance Code (Available Capacitance)
C052H102(1)5R5GA(2)
C052H122(1)5R5GA(2)
C052H152(1)5R5GA(2)
C052H182(1)5R5GA(2)
C052H222(1)5R5GA(2)
C052H272(1)5R5GA(2)
C052H332(1)5R5GA(2)
C052H392(1)5R5GA(2)
C052H472(1)5R5GA(2)
C052H562(1)5R5GA(2)
C052H682(1)5R5GA(2)
C052H822(1)5R5GA(2)
C052H103(1)5R5GA(2)
C052H123(1)5R5GA(2)
C052H153(1)5R5GA(2)
C052H183(1)5R5GA(2)
C052H223(1)5R5GA(2)
C052H273(1)5R5GA(2)
C052H333(1)5R5GA(2)
C052H393(1)5R5GA(2)
C052H473(1)5R5GA(2)
C052H563(1)5R5GA(2)
C052H683(1)5R5GA(2)
C052H823(1)5R5GA(2)
C052H104(1)5R5GA(2)
C052H102(1)1R5GA(2)
C052H122(1)1R5GA(2)
C052H152(1)1R5GA(2)
C052H182(1)1R5GA(2)
C052H222(1)1R5GA(2)
C052H272(1)1R5GA(2)
C052H332(1)1R5GA(2)
C052H392(1)1R5GA(2)
C052H472(1)1R5GA(2)
C052H562(1)1R5GA(2)
C052H682(1)1R5GA(2)
C052H822(1)1R5GA(2)
C052H103(1)1R5GA(2)
C052H123(1)1R5GA(2)
C052H153(1)1R5GA(2)
C052H183(1)1R5GA(2)
C052H223(1)1R5GA(2)
C052H273(1)1R5GA(2)
C052H333(1)1R5GA(2)
C052H393(1)1R5GA(2)
C052H473(1)1R5GA(2)
C052H102(1)2R5GA(2)
C052H122(1)2R5GA(2)
C052H152(1)2R5GA(2)
C052H182(1)2R5GA(2)
C052H222(1)2R5GA(2)
C052H272(1)2R5GA(2)
C052H332(1)2R5GA(2)
Rated Voltage (VDC)
50
100
200
Voltage Code
5
1
2
J = ±5%
K = ±10%
M = ±20%
(1) To complete ordering code, insert the proper character for capacitance tolerance: (See table above for character definitions)
(1) Available capacitance tolerances: J, K, M
(2) To complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code." See details below:
Blank = Bulk Bag
T250 = 250 pcs / 12" Reel
T500 = 500pcs / 12" Reel
T1K0 = 1,000 pcs / 12" reel
7301 = Full Reel Qty / 12" reel
7303 = Full Reel Qty / 12" reel
7061 = Bulk Tray
These products are protected under U.S. Patents 7172985 and 7670981, other patents pending, and any foreign counterparts.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1074_HT_X7R_RADIAL_MOLDED • 8/10/2016
4
Radial Through-Hole Multilayer Ceramic Capacitors
High Temperature 200°C, Radial, Molded, X7R Dielectric, 50 – 200 VDC (Industrial Grade)
Table 1B – C062 Style/Size (0.20" Lead Spacing), Capacitance Range Waterfall
C062 Style/Size (0.20" Lead Spacing)
Rated Voltage (VDC)
50
100
200
Voltage Code
5
1
2
Capacitance
Tolerance
Capacitance
4,700 pF
5,600 pF
6,800 pF
0.056 µF
0.068 µF
0.082 µF
0.1 µF
0.12 µF
0.15 µF
0.18 µF
0.22 µF
0.27 µF
0.33 µF
0.39 µF
0.47 µF
0.56 µF
0.68 µF
0.82 µF
1.0 µF
Capacitance Code (Available Capacitance)
C062H124(1)5R5GA(2)
C062H154(1)5R5GA(2)
C062H184(1)5R5GA(2)
C062H224(1)5R5GA(2)
C062H274(1)5R5GA(2)
C062H334(1)5R5GA(2)
C062H394(1)5R5GA(2)
C062H474(1)5R5GA(2)
C062H564(1)5R5GA(2)
C062H684(1)5R5GA(2)
C062H824(1)5R5GA(2)
C062H105(1)5R5GA(2)
J = ±5%
K = ±10%
M = ±20%
C062H472(1)2R5GA(2)
C062H562(1)2R5GA(2)
C062H682(1)2R5GA(2)
C062H563(1)1R5GA(2)
C062H683(1)1R5GA(2)
C062H823(1)1R5GA(2)
C062H104(1)1R5GA(2)
C062H124(1)1R5GA(2)
Rated Voltage (VDC)
50
100
200
Voltage Code
5
1
2
(1) To complete ordering code, insert the proper character for capacitance tolerance: (See table above for character definitions)
(1) Available capacitance tolerances: J, K, M
(2) To complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code." See details below:
Blank = Bulk Bag
T250 = 250 pcs / 12" Reel
T500 = 500pcs / 12" Reel
T1K0 = 1,000 pcs / 12" reel
7301 = Full Reel Qty / 12" reel
7303 = Full Reel Qty / 12" reel
7061 = Bulk Tray
These products are protected under U.S. Patents 7172985 and 7670981, other patents pending, and any foreign counterparts.
Packaging Quantities
Packaging Options
Bulk Bag
(default)1
Bulk Tray
Tape and Reel
Packaging Quantities3
Ordering Code
C-Spec2
Style/
Series
n/a
7061
T250
T500
T1K0
7301
7303
C052H
100 pcs/bag
50 pcs/tray
250
500
1,000
2,000
n/a
C062H
100 pcs/bag
40 pcs/tray
250
500
1,000
n/a
1,500
Default packaging for this product series is "Bulk Bag". KEMET will assume " Bulk Bag" packaging is required unless a valid C-spec is included in the
15th thru 18th character positions of the ordering code. For more information see "Ordering Information" section of this document.
1, 2
The " Ordering Code C-Spec" is a four-digit code that follows the KEMET part number and identifies any special packaging or processing
requirements. Failure to include a C-Spec when ordering will result in the default packaging option. Default packaging for this product series is "Bulk
Bag".
3
Packaging quantities reported above are considered "minimum order quantities" and are mandatory.
1
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1074_HT_X7R_RADIAL_MOLDED • 8/10/2016
5
Radial Through-Hole Multilayer Ceramic Capacitors
High Temperature 200°C, Radial, Molded, X7R Dielectric, 50 – 200 VDC (Industrial Grade)
Soldering Process
Recommended Soldering Technique:
• Solder Wave
• Hand Soldering (Manual)
Recommended Soldering Profile:
• Optimum Wave Solder Profile
Solder Wave Peak
Temperature 260ºC
Entrance to Solder Wave
Degrees – Cº
Flux Zone
250
225
200
175
150
125
100
75
50
25
Exit from Solder Wave
(Time in Wave – 2 to 4 Seconds)
Preheat Zone
Hot Air Debridging
Exit from
Solder
Machine
80ºC
to 120ºC
Entrance
to Solder
Machine
Free
Air
Cool
Bottom Side
Temperature
Range
Entrance to
In-Line Cleaner
Exit from
In-Line Cleaner
(time in cleaner
may be less)
Immersion in
Cleaning
Vapor
150ºC
Maximum
Top Side
Nominal
0
1
2
3
Time (Minutes)
4
5
6
• Hand Soldering (Manual)
Manual Solder Profile with Pre-heating
Soldering
Gradual Cooling
Gradual Preheat
60 – 120 Seconds
Recommend 2.5ºC/second
Maximum 3 seconds
Delta T < = 120ºC
KEMET recommends following the guidelines and techniques outlined in technical bulletins F2103 and F9207.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1074_HT_X7R_RADIAL_MOLDED • 8/10/2016
6
Radial Through-Hole Multilayer Ceramic Capacitors
High Temperature 200°C, Radial, Molded, X7R Dielectric, 50 – 200 VDC (Industrial Grade)
Table 2 – Performance & Reliability: Test Methods and Conditions
Stress
Reference
Solderability
J–STD–002
Temperature Cycling
JESD22 Method JA–104
Biased Humidity
MIL–STD–202 Method
103
Immersion
Storage Life
High Temperature Life
High Temperature
Lead Pull
Vibration
Resistance to Soldering
Heat
Terminal Strength
Mechanical Shock
Resistance to Solvents
MIL–STD–202 Method
104
MIL–STD–202 Method
108
MIL–STD–202 Method
108
KEMET Defined Test
MIL–STD–202 Method
204
MIL–STD–202 Method
210
MIL–STD–202 Method
211
MIL–STD–202 Method
213
MIL–STD–202 Method
215
Test or Inspection Method
Method A at 235°C, category 3
50 cycles (−55°C to 220°C), measurement at 24 ±4 hours after test conclusion. 30 minutes
maximum dwell time at each temperature extreme. 8 minutes maximum transition time.
Load humidity: 1,000 hours 85°C/85% RH and rated voltage. Add 100 K ohm resistor.
Measurement at 24 hours ±4 hours after test conclusion.
Low volt humidity: 1,000 hours 85°C/85% RH and 1.5 V. Add 100 K ohm resistor.
Measurement at 24 hours ±4 hours after test conclusion.
Test condition B
Unpowered 1,000 hours at 200°C. Measurement at 24 hours ±4 hours after test conclusion.
IR Measurement at 150°C
1,000 hours at 200°C with rated voltage applied.
Peel to Failure (25ºC and 200ºC): 4 lbs (1.84 kg) minimum
5g for 20 minutes, 12 cycles each of 3 orientations. Note: Use 8" X 5" PCB. 031" thick 7
secure points on one long side and 2 secure points at corners of opposite sides. Parts
mounted within 2" from any secure point. Test from 10 – 2000 Hz.
Test Condition B, Solder dip. Note: no preheat of samples.
Test Condition A. 454g 5 – 10 s; Bend test © 227g, 3 bends
Test Condition D. Figure 1 of Method 213.
Add aqueous wash chemical – OKEM Clean or equivalent.
Storage & Handling
The un-mounted storage life of a through-hole (leaded) ceramic capacitor is dependent upon storage and atmospheric
conditions as well as packaging materials. While the ceramic chips enveloped under the epoxy coating themselves are quite
robust in most environments, solderability of the wire lead on the final epoxy-coated product will be degraded by exposure
to high temperatures, high humidity, corrosive atmospheres, and long term storage. In addition, packaging materials will be
degraded by high temperature and exposure to direct sunlight–reels may soften or warp, and tape peel force may increase.
KEMET recommends storing the un-mounted capacitors in their original packaging, in a location away from direct sunlight,
and where the temperature and relative humidity do not exceed 40 degrees centigrade and 70% respectively. For optimum
solderability, capacitor stock should be used promptly, preferably within 18 months of receipt. For applications requiring
pre-tinning of components, storage life may be extended if solderability is verified. Before cleaning, bonding or molding these
devices, it is important to verify that your process does not affect product quality and performance. KEMET recommends
testing and evaluating the performance of a cleaned, bonded or molded product prior to implementing and/or qualifying any
of these processes.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1074_HT_X7R_RADIAL_MOLDED • 8/10/2016
7
Radial Through-Hole Multilayer Ceramic Capacitors
High Temperature 200°C, Radial, Molded, X7R Dielectric, 50 – 200 VDC (Industrial Grade)
Application Notes
Working Voltage:
Application voltage (Vp-p or Vo-p) must not exceed the voltage rating of the capacitor. Irregular voltages can be generated
for a transient period of time when voltage is initially applied and/or removed from a circuit. It is important to choose a
capacitor with a voltage rating greater than or equal to these irregular voltages.
Operating Temperature and Self-Generating Heat:
The surface temperature of a capacitor should be kept below the upper limit of its rated operating temperature range. Be
sure to take into account the heat generated by the capacitor itself. When the capacitor is used in a high-frequency current,
pulse current or similar current, it may self-generate heat due to dielectric loss. Temperature rise due to self-generated
heating should not exceed 20°C (while operated at an atmosphere temperature of 25°C).
FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY RESULT, WORST CASE, IN A SHORT CIRCUIT AND CAUSE FUMING OR
PARTIAL DISPERSION WHEN THE PRODUCT IS USED.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1074_HT_X7R_RADIAL_MOLDED • 8/10/2016
8
Radial Through-Hole Multilayer Ceramic Capacitors
High Temperature 200°C, Radial, Molded, X7R Dielectric, 50 – 200 VDC (Industrial Grade)
Construction
Base Metal Electrode
Epoxy
Encapsulation
Finish Layer
(Sn10/Pb88/Ag2)
Detailed Cross Section
Barrier Layer
(Ni)
Base Metal
(Cu)
Lead Attach Solder
(Sn10/Pb88/Ag2)
Lead Attach Solder
(Sn10/Pb88/Ag2)
Dielectric
Material (CaZrO3)
Inner Electrodes
(Ni)
Barrier Layer
(Ni)
Base Metal
(Cu)
Finish Layer
(Sn10/Pb88/Ag2)
Lead Wire
Core Metal
Barrier Layer 1
Barrier Layer 2
Finish Layer
Steel
Cu
Ni
Au
Precious Metal Electrode
Inner Electrodes
(Ni)
Epoxy
Encapsulation
Detailed Cross Section
Epoxy
Encapsulation
Chip End
Metalization
(Solderable Silver)
Lead Attach Solder
(Sn10/Pb88/Ag2)
Lead Attach Solder
(Sn10/Pb88/Ag2)
Dielectric
Material (BaTiO3)
Inner Electrodes
(PdAg)
Chip End
Metalization
(Solderable Silver)
Lead Wire
Core Metal
Barrier Layer 1
Barrier Layer 2
Finish Layer
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
Steel
Cu
Ni
Au
Inner Electrodes
Epoxy (PdAg)
Encapsulation
C1074_HT_X7R_RADIAL_MOLDED • 8/10/2016
9
Radial Through-Hole Multilayer Ceramic Capacitors
High Temperature 200°C, Radial, Molded, X7R Dielectric, 50 – 200 VDC (Industrial Grade)
Marking
FRONT
BACK
Rated Voltage
(VDC)
Style/Size
Dielectric
Specification/Series
KEMET ID
Rated Capacitance
Capacitance
Tolerance Code
Date Code
Date Code
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
14
20
Manufacturing Year:
14 = 2014
Manufacturing Week:
20 = Week 20
(of mfg. calendar year)
C1074_HT_X7R_RADIAL_MOLDED • 8/10/2016
10
Radial Through-Hole Multilayer Ceramic Capacitors
High Temperature 200°C, Radial, Molded, X7R Dielectric, 50 – 200 VDC (Industrial Grade)
Lead Tape & Reel Packaging Information
KEMET offers standard reeling of Molded Radial Leaded
Capacitors in accordance with EIA standard 468. Parts
are taped to a tag board carrier strip, and wound on a reel
as shown in Figure 1. Kraft paper interleaving is inserted
between the layers of capacitors on the reel.
t
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1074_HT_X7R_RADIAL_MOLDED • 8/10/2016
11
Radial Through-Hole Multilayer Ceramic Capacitors
High Temperature 200°C, Radial, Molded, X7R Dielectric, 50 – 200 VDC (Industrial Grade)
Table 3 – Ceramic Radial Tape and Reel Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
D0
P2
P0
P
∆H
±0.2 (0.008) ±0.3 (0.012) ±0.3 (0.012) ±0.7 (0.028) Maximum
L1
Maximum
t
Maximum
W
T
W0
+ 1.0/−0.5
Maximum (+0.039/−0.020) Minimum
4.00 (0.157) 12.7 (0.500) 12.7 (0.500) 6.35 (0.250) 1.0 (0.039) 1.0 (0.039) 0.9 (0.035) 2.0 (0.079)
18.0 (0.709)
W2
Maximum
5.0 (0.197) 3.0 (0.118)
Symbol Reference Table
Variable Dimensions — Millimeters (Inches)
F
+0.6 (0.024)
−0.2 (0.008)
Note 1
P1
±0.7 (0.028)
Note 1
2.54 (0.100)
5.08 (0.200)
4.32 (0.170)
3.89 (0.153)
P1
5.08 (0.200)
3.81 (0.150)
5.59 (0.220)
D0
Sprocket Hole Diameter
P0
Sprocket Hole Pitch
P
Component Pitch
F
P2
Lead Spacing
Sprocket Hole Center to Adjacent Component
Lead
Sprocket Hole Center to Component Center
3.25 (0.128)
H
Height to Seating Plane (Straight Leads Only)
6.98 (0.275)
2.54 (0.100)
H0
Height to Seating Plane (Formed Leads Only)
7.62 (0.300)
2.24 (0.088)
H1
Component Height Above Tape Center
9.52 (0.375)
7.62 (0.300)
∆H
Component Alignment
10.16 (0.400)
7.34 (0.290)
L1
Lead Protrusion
12.06 (0.475)
6.35 (0.250)
t
W
Composite Tape Thickness
Carrier Tape Width
14.60 (0.575)
5.08 (0.200)
W0
Hold-Down Tape Width
17.14 (0.675)
3.81 (0.15)
W2
Hold-Down Tape Location
H
Minimum
Note 2
18.0 (0.709)
H0
±0.5 (0.630)
Note 3
16.0 (0.024)
1. Measured at the egress from the carrier tape, on the component side.
2. Straight Lead configuration part types only.
3. Formed (bent) lead configuration part types only.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1074_HT_X7R_RADIAL_MOLDED • 8/10/2016
12
Radial Through-Hole Multilayer Ceramic Capacitors
High Temperature 200°C, Radial, Molded, X7R Dielectric, 50 – 200 VDC (Industrial Grade)
KEMET Electronic Corporation Sales Offices
For a complete list of our global sales offices, please visit www.kemet.com/sales.
Disclaimer
All product specifications, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for
checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.
All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such
applications, but are not intended to constitute – and KEMET specifically disclaims – any warranty concerning suitability for a specific customer application or use.
The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any
technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no
obligation or liability for the advice given or results obtained.
Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component
failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards
(such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or
property damage.
Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other
measures may not be required.
KEMET is a registered trademark of KEMET Electronics Corporation.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1074_HT_X7R_RADIAL_MOLDED • 8/10/2016
13
Similar pages