LITEON LTW-C192TS5 Property of lite-on only Datasheet

LITE-ON
TECHNOLOGY
CORPORATION
Property of Lite-On Only
Features
* Super thin (0.40H mm) Chip LED.
* Ultra bright InGaN White Chip LED.
* Package in 8mm tape on 7" diameter reels.
* Compatible with automatic placement equipment.
* Compatible with infrared and vapor phase reflow solder process.
* EIA STD package.
* I.C. compatible.
Package
Dimensions
Part No.
Lens
Emitted Color
LTW-C192TS5
Yellow
InGaN White
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ± 0.10 mm (.004") unless otherwise noted.
Part
No. : LTW-C192TS5
BNS-OD-C131/A4
Page :
1
of
11
LITE-ON
TECHNOLOGY
CORPORATION
Property of Lite-On Only
Absolute
Maximum
Ratings
Parameter
At
Ta=25℃
LTW-C192TS5
Unit
Power Dissipation
70
mW
Peak Forward Current
(1/10 Duty Cycle, 0.1ms Pulse Width)
100
mA
DC Forward Current
20
mA
0.25
mA/°C
5
V
Derating Linear From 25°C
Reverse Voltage
Operating Temperature Range
-20°C to + 80°C
Storage Temperature Range
-55°C to + 105°C
Wave Soldering Condition
260°C For 5 Seconds
Suggest IR Reflow Condition :
R e c o m m e n d e d P r o file B e t w e e n A s s e m b le A n d H e a t-R e s is ta n c e L in e
T h e P ro file is a v a ila b le t h a t m u s t t o u s e S n A g
Part
No. : LTW-C192TS5
BNS-OD-C131/A4
Cu
Page :
s o ld e r p a s t e
2
of
11
LITE-ON
TECHNOLOGY
CORPORATION
Property of Lite-On Only
Electrical
Optical
Characteristics
Parameter
Luminous Intensity
Viewing Angle
Symbol
At
Ta=25℃
Part No.
LTW-
IV
C192TS5
2θ1/2
C192TS5
Min.
28.0
Max.
Unit
Test Condition
112.0
mcd
IF = 5mA
Note 1, 2, 5
deg
Fig.6
130
x
Chromaticity Coordinates
Typ.
IF = 5mA
Note 3, 5
Fig.1
0.294
C192TS5
y
0.286
Forward Voltage
VF
C192TS5
Reverse Current
IR
C192TS5
2.70
3.15
V
IF = 5mA
10
µA
VR = 5V
Note : 1. Luminous intensity is measured with a light sensor and filter combination that approximates the
CIE eye-response curve.
2. Iv classification code is marked on each packing bag.
3. The chromaticity coordinates (x, y) is derived from the 1931 CIE chromaticity diagram.
4. Caution in ESD:
Static Electricity and surge damages the LED. It is recommend to use a wrist band or anti-electrostatic
glove when handling the LED. All devices, equipment and machinery must be properly grounded.
5. Tester
z CAS140B is for the chromaticity coordinates (x, y) and Iv.
6. The chromaticity coordinates (x, y) guarantee should be added ± 0.01 tolerance.
Part
No. : LTW-C192TS5
BNS-OD-C131/A4
Page :
3
of
11
LITE-ON
TECHNOLOGY
CORPORATION
Property of Lite-On Only
Typical
(25℃
Part
No. : LTW-C192TS5
BNS-OD-C131/A4
Electrical
Ambient
/
Optical
Temperature
Characteristics
Unless
Otherwise
Curves
Noted)
Page :
4
of
11
LITE-ON
TECHNOLOGY
CORPORATION
Property of Lite-On Only
Bin Code List
VF Spec. Table
Forward Voltage (V) at IF = 5mA
VF Bin
Min.
Max.
A
2.70
2.85
B
2.85
3.00
C
3.00
3.15
Tolerance on each Forward Voltage bin is +/-0.1 volt
IV Spec. Table
Luminous Intensity (mcd) at IF = 5mA
IV Bin
Min.
Max.
N
28.0
45.0
P
45.0
71.0
Q
71.0
112.0
Tolerance on each Luminous Intensity bin is +/- 15%.
Hue Spec. Table
Color bin limits at IF = 5mA
Hue Bin
CIE 1931Chromaticity coordinates
S1
S2
S3
S4
S5
S6
x
0.274
0.274
0.294
0.294
y
0.226
0.258
0.286
0.254
x
0.274
0.274
0.294
0.294
y
0.258
0.291
0.319
0.286
x
0.294
0.294
0.314
0.314
y
0.254
0.286
0.315
0.282
x
0.294
0.294
0.314
0.314
y
0.286
0.319
0.347
0.315
x
0.314
0.314
0.334
0.334
y
0.282
0.315
0.343
0.311
x
0.314
0.314
0.334
0.334
y
0.315
0.347
0.376
0.343
Tolerance on each Hue (x, y) bin is +/- 0.01.
C. I. E. 1931 Chromaticity Diagram
0.4
Y-coordinate
0.35
S6
S4
0.3
S2
Part
No. : LTW-C192TS5
BNS-OD-C131/A4
S3
S1
0.25
0.2
0.25
S5
0.27
0.29
0.31
X-coordinate
0.33
0.35
Page :
5
of
11
LITE-ON
TECHNOLOGY
CORPORATION
Property of Lite-On Only
Cleaning
Do not use unspecified chemical liquid to clean LED they could harm the package.
If clean is necessary, immerse the LED in ethyl alcohol or in isopropyl alcohol at normal temperature
for less one minute.
Suggest Soldering Pad Dimensions
Package Dimensions Of Tape And Reel
Notes:
1. All dimensions are in millimeters (inches).
Part
No. : LTW-C192TS5
BNS-OD-C131/A4
Page :
6
of
11
LITE-ON
TECHNOLOGY
CORPORATION
Property of Lite-On Only
Package Dimensions of Reel
Notes:
1. Empty component pockets sealed with top cover tape.
2. 7 inch reel-3000 pieces per reel.
3. Minimum packing quantity is 500 pieces for remainders.
4. The maximum number of consecutive missing lamps is two.
5. In accordance with ANSI/EIA 481-1-A-1994 specifications.
Part
No. : LTW-C192TS5
BNS-OD-C131/A4
Page :
7
of
11
LITE-ON
TECHNOLOGY
CORPORATION
Property of Lite-On Only
Notes:
1. There are 3 moisture barrier bags or less in inner carton.
2. There are 21 inner carton or less in a master carton.
Part
No. : LTW-C192TS5
BNS-OD-C131/A4
Page :
8
of
11
LITE-ON
TECHNOLOGY
CORPORATION
Property of Lite-On Only
CAUTIONS
1. Application
The LEDs described here are intended to be used for ordinary electronic equipment (such as office
equipment, communication equipment and household applications).Consult Liteon’s Sales in advance
for information on applications in which exceptional reliability is required, particularly when the failure
or malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation,
traffic control equipment, medical and life support systems and safety devices).
2. Storage
The storage ambient for the LEDs should not exceed 30°C temperature or 70% relative humidity.
It is recommended that LEDs out of their original packaging are IR-reflowed within one week.
For extended storage out of their original packaging, it is recommended that the LEDs be stored in a
sealed container with appropriate desiccant, or in a desiccators with nitrogen ambient.
LEDs stored out of their original packaging for more than a week should be baked at about 60 deg C
for at least 24 hours before solder assembly.
3. Cleaning
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED if necessary.
4. Soldering
Recommended soldering conditions:
Reflow soldering
Pre-heat
Pre-heat time
Peak temperature
Soldering time
120~150°C
120 sec. Max.
240°C Max.
10 sec. Max.
Wave Soldering
Pre-heat
Pre-heat time
Solder wave
Soldering time
Soldering iron
100°C Max.
60 sec. Max.
260°C Max.
10 sec. Max.
Temperature
Soldering time
300°C Max.
3 sec. Max.
(one time only)
5. Drive Method
An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs
connected in parallel in an application, it is recommended that a current limiting resistor be incorporated
in the drive circuit, in series with each LED as shown in Circuit A below.
Circuit model A
LED
Circuit model B
LED
(A) Recommended circuit.
(B) The brightness of each LED might appear different due to the differences in the I-V characteristics
of those LEDs.
6. ESD (Electrostatic Discharge)
Static Electricity or power surge will damage the LED.
Suggestions to prevent ESD damage:
„
„
„
„
Part
Use of a conductive wrist band or anti-electrostatic glove when handling these LEDs.
All devices, equipment, and machinery must be properly grounded.
Work tables, storage racks, etc. should be properly grounded.
Use ion blower to neutralize the static charge which might have built up on surface of the LED’s
plastic lens as a result of friction between LEDs during storage and handling.
No. : LTW-C192TS5
BNS-OD-C131/A4
Page :
9
of
11
LITE-ON
TECHNOLOGY
CORPORATION
Property of Lite-On Only
ESD-damaged LEDs will exhibit abnormal characteristics such as high reverse leakage current, low forward
voltage, or “ no lightup ” at low currents.
To verify for ESD damage, check for “ lightup ” and Vf of the suspect LEDs at low currents.
The Vf of “ good ” LEDs should be >[email protected] for InGaN product and >[email protected] for AlInGaP product.
7. Reliability Test
Classification
Test Item
Reference Standard
Ta= Under Room Temperature As Per Data Sheet
Maximum Rating
*Test Time= 1000HRS (-24HRS,+72HRS)*@20mA.
MIL-STD-750D:1026 (1995)
MIL-STD-883D:1005 (1991)
JIS C 7021:B-1 (1982)
High Temperature
High Humidity
Storage
IR-Reflow In-Board, 2 Times
Ta= 65±5℃,RH= 90~95%
*Test Time= 240HRS±2HRS
MIL-STD-202F:103B(1980)
JIS C 7021:B-11(1982)
High Temperature
Storage
Ta= 105±5℃
*Test Time= 1000HRS (-24HRS,+72HRS)
MIL-STD-883D:1008 (1991)
JIS C 7021:B-10 (1982)
Low Temperature
Storage
Ta= -55±5℃
*Test Time=1000HRS (-24HRS,+72H RS)
JIS C 7021:B-12 (1982)
105℃ ~ 25℃ ~ -55℃ ~ 25℃
30mins 5mins
30mins 5mins
10 Cycles
MIL-STD-202F:107D (1980)
MIL-STD-750D:1051(1995)
MIL-STD-883D:1010 (1991)
JIS C 7021:A-4(1982)
IR-Reflow In-Board, 2 Times
85 ± 5℃ ~ -40℃ ± 5℃
10mins
10mins 10 Cycles
MIL-STD-202F:107D(1980)
MIL-STD-750D:1051(1995)
MIL-STD-883D:1011 (1991)
Solder
Resistance
T.sol= 260 ± 5℃
Dwell Time= 10 ± 1secs
MIL-STD-202F:210A(1980)
MIL-STD-750D:2031(1995)
JIS C 7021:A-1(1982)
IR-Reflow
Ramp-up rate(217℃ to Peak) +3℃/ second max
Temp. maintain at 175(±25)℃ 180 seconds max
Temp. maintain above 217℃ 60-150 seconds
Peak temperature range 260℃+0/-5℃
Time within 5°C of actual Peak Temperature (tp)
20-40 seconds
Ramp-down rate +6℃/second max
Operation Life
Endurance
Test
Test Condition
Temperature
Cycling
Thermal
Shock
Environmental
Test
Solderability
T.sol= 235 ± 5℃
Immersion time 2±0.5 sec
Immersion rate 25±2.5 mm/sec
Coverage ≧95% of the dipped surface
MIL-STD-750D:2031.2(1995)
J-STD-020(1999)
MIL-STD-202F:208D(1980)
MIL-STD-750D:2026(1995)
MIL-STD-883D:2003(1991)
IEC 68 Part 2-20
JIS C 7021:A-2(1982)
8. Others
The appearance and specifications of the product may be modified for improvement without prior notice.
Part
No. : LTW-C192TS5
BNS-OD-C131/A4
Page :
10
of
11
LITE-ON
TECHNOLOGY
CORPORATION
Property of Lite-On Only
9. Suggested Checking List
Training and Certification
1. Everyone working in a static-safe area is ESD-certified?
2. Training records kept and re-certification dates monitored?
Static-Safe Workstation & Work Areas
1. Static-safe workstation or work-areas have ESD signs?
2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V?
3. All ionizer activated, positioned towards the units?
4. Each work surface mats grounding is good?
Personnel Grounding
1. Every person (including visitors) handling ESD sensitive (ESDS) items wears wrist strap, heel
strap or conductive shoes with conductive flooring?
2. If conductive footwear used, conductive flooring also present where operator stand or walk?
3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*?
4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DLs?
5. All wrist strap or heel strap checkers calibration up to date?
Note: *50V for Blue LED.
Device Handling
1. Every ESDS items identified by EIA-471 labels on item or packaging?
2. All ESDS items completely inside properly closed static-shielding containers when not at
static-safe workstation?
3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items?
4. All flexible conductive and dissipative package materials inspected before reuse or recycles?
Others
1. Audit result reported to entity ESD control coordinator?
2. Corrective action from previous audits completed?
3. Are audit records complete and on file?
Part
No. : LTW-C192TS5
BNS-OD-C131/A4
Page :
11
of
11
Similar pages