Maxim MAX258 Integrated system protection Datasheet

EVALUATION KIT AVAILABLE
MAX258
500mA, Push-Pull Transformer Driver
for Isolated Power Supplies
General Description
Features and Benefits
The MAX258 is a 500mA, push-pull transformer driver
designed to provide a simple solution for isolated power
supplies. The IC has an internal oscillator and operates
from a single +3.0V to +5.5V supply. The transformer’s
secondary-to-primary winding ratio defines the output
voltage, allowing selection of virtually any isolated output
voltage with galvanic isolation.
The device features an integrated oscillator driving a pair
of n-channel power switches. Internal circuitry guarantees
a fixed 50% duty cycle to prevent DC current flow through
the transformer.
The IC operates with up to 500mA of continuous current
and features undervoltage lockout and thermal shutdown.
The IC includes a low-current shutdown mode to reduce
the overall supply current to less than 5µA (max) when the
driver is disabled.
The MAX258 is available in a small 8-pin (2mm x 3mm)
TDFN package and is specified over the -40°C to +125°C
temperature range.
● Simple, Flexible Design
• +3.0V to +5.5V Supply Range
• Low RON 300mΩ (max) at 4.5V
• Up to 90% Efficiency
• Provides Up to 500mA to the Transformer
• 250kHz or 600kHz Internal Oscillator Frequency
• -40ºC to +125ºC Temperature Range
● Integrated System Protection
• Undervoltage Lockout
• Thermal Shutdown
● Saves Space on Board
• Small 8-Pin TDFN Package (2mm x 3mm)
Applications
●
●
●
●
Power Meter Data Interface
Isolated Fieldbus Interface
Medical Equipment
Isolated Analog Front-End
Ordering Information appears at end of data sheet.
Typical Operating Circuit
5V
1µF
VDD
HICLK
T2
1CT:1.3CT
1µF ISOLATED
VOUT
MAX258
10µF
EN
T1
GND
PGND
For related parts and recommended products to use with this part, refer to www.maximintegrated.com/MAX258.related.
19-6696; Rev 0; 5/13
MAX258
500mA, Push-Pull Transformer Driver
for Isolated Power Supplies
Absolute Maximum Ratings
Operating Temperature Range...........................-40ºC to +125ºC
Junction Temperature....................................................... +150ºC
Storage Temperature Range..............................-65ºC to +150°C
Lead Temperature (soldering, 10s).................................. +300°C
Soldering Temperature (reflow)........................................+260°C
(All voltages referenced to GND.)
VDD, HICLK, EN.......................................................-0.3V to +6V
T1, T2..................................................................-0.3V to +16.5V
T1, T2 Maximum Continuous Current...............................+1.75A
Continuous Power Dissipation (TA = +70ºC)
TDFN (Multilayer Board)
(derate 16.7mW/ºC above +70ºC)...........................1333.3mW
Package Thermal Characteristics (Note 1)
TDFN (Multilayer)
Junction-to-Ambient Thermal Resistance (θJA)...........60°C/W
Junction-to-Case Thermal Resistance (θJC)................11°C/W
Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer
board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/thermal-tutorial.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Electrical Characteristics
(VDD = +3.0V to 5.5V, TA = TMIN to TMAX, unless otherwise noted. Typical values at VDD = +5.0V and TA = +25ºC.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
5.5
V
DC CHARACTERISTICS
Supply Voltage Range
3.0
VDD
VHICLK = 0V
1.1
1.8
VHICLK = VDD
2.1
3.5
Supply Current
IDD
VEN = 0V, T1 and T2 not
connected
Disable Supply Current
IDIS
VEN = VDD, T1, T2, HICLK connected to GND
or VDD (Note 3)
Driver Output Resistance
RO
IOUT = 500mA
Undervoltage Lockout
Threshold
VUVLO
Undervoltage Lockout
Threshold Hysteresis
VUVLO_HYST
T1, T2 Leakage Current
ILKG
5
VDD = 3.0V
160
350
VDD = 4.5V
145
300
2.75
2.9
VDD rising
2.6
250
VEN = VDD, T1, T2 = 0V or VDD
-1
mA
µA
mΩ
V
mV
+1
µA
LOGIC SIGNALS (EN, HICLK)
Input Logic-High Voltage
VIH
Input Logic-Low Voltage
VIL
Input Leakage Current
IIL
www.maximintegrated.com
2
EN, HICLK = 0V or 5.5V
-1
V
0.8
V
+1
µA
Maxim Integrated │ 2
MAX258
500mA, Push-Pull Transformer Driver
for Isolated Power Supplies
Electrical Characteristics (continued)
(VDD = +3.0V to 5.5V, TA = TMIN to TMAX, unless otherwise noted. Typical values at VDD = +5.0V and TA = +25ºC.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
VHICLK = 0V
237
250
263
VHICLK = VDD
564
600
636
UNITS
AC CHARACTERISTICS
Switching Frequency
fSW
T1, T2 Duty Cycle
D
T1, T2 Slew Rate
tSLEW
Crossover Dead Time
tDEAD
Figure 1
kHz
50
%
Figure 1
200
V/µs
Figure 1
50
ns
PROTECTION
Thermal-Shutdown
Threshold
TSHDN
+160
ºC
Thermal-Shutdown
Hysteresis
TSHDN_HYS
30
ºC
Note 2: All units are 100% production tested at TA = +25ºC. Specifications over temperature are guaranteed by design.
Note 3: Disable supply current includes output-switch-leakage currents.
VDD
100I
T1, T2
50pF
2 x VDD
T1
0V
2 x VDD
tDEAD
tDEAD
T2
0V
Figure 1. T1, T2 Timing Diagram
www.maximintegrated.com
Maxim Integrated │ 3
MAX258
500mA, Push-Pull Transformer Driver
for Isolated Power Supplies
Typical Operating Characteristics
(VDD = +5V, TA = +25°C, unless otherwise noted.)
HICLK = VDD
510
460
410
360
HICLK = GND
310
260
VDD = 3.3V
0.07
0.06
0.05
VDD = 5V
0.04
0.03
0.02
0.01
-45
-20
5
30
55
80
105
0
130
0.1
0.2
0.3
0.4
0.10
0.20
0.10
0.20
TA = +85°C
TA = -40°C
0
LOAD CURRENT (A)
www.maximintegrated.com
0.20
0.30
0.40
MAX258 toc07
93
91
89
87
VDD = 5V
85
83
81
75
VDD = 4.5V
VDD = 5.5V
HICLK = GND
1:1:1.3:1.3
HALO TGM-H240V8LF
TRANSFORMER
77
0.40
0.10
HICLK = GND
1:1:1.3:1.3
HALO TGM-H240V8LF
TRANSFORMER
EFFICIENCY vs. LOAD CURRENT
79
0.30
0.4
TA = +25°C
95
MAX258 toc06
1:1:1:3:1:3
HALO TGM-H240V8LF
TRANSFORMER
0.3
LOAD CURRENT (A)
EFFICIENCY (%)
EFFICIENCY (%)
80
0.2
TA = +125°C
82
0.25
HICLK = VDD
0
0.1
0
84
78
0.15
HICLK = GND
70
HICLK = GND
1:1:1.3:1.3
HALO TGM-H240V8LF
TRANSFORMER
2
80
90
75
3
86
EFFICIENCY vs. LOAD CURRENT
85
4
EFFICIENCY vs. LOAD CURRENT
LOAD CURRENT (A)
95
5
88
HICLK = GND
1:1:2:2
HALO TGM-H260V8LF
TRANSFORMER
0.05
6
LOAD CURRENT (A)
EFFICIENCY (%)
8
7
0
7
0
0.5
90
9
1
0
0
MAX258 toc04
ISOLATED OUTPUT VOLTAGE (V)
11
10
3
2
8
1
ISOLATED OUTPUT VOLTAGE
vs. LOAD CURRENT
6
5
4
9
OUTPUT CURRENT (A)
TEMPERATURE (°C)
12
10
MAX258 toc05
210
0.08
ISOLATED OUTPUT VOLTAGE
vs. LOAD CURRENT
MAX258 toc03
560
T1/T2 OUTPUT VOLTAGE LOW (V)
610
0.09
ISOLATED OUTPUT VOLTAGE (V)
0.10
MAX258 toc01
SWITCHING FREQUENCY (kHz)
660
T1/T2 OUTPUT VOLTAGE
LOW vs. OUTPUT CURRENT
MAX258 toc02
SWITCHING FREQUENCY
vs. TEMPERATURE
0
0.1
0.2
0.3
0.4
LOAD CURRENT (A)
Maxim Integrated │ 4
MAX258
500mA, Push-Pull Transformer Driver
for Isolated Power Supplies
Typical Operating Characteristics (continued)
(VDD = +5V, TA = +25°C, unless otherwise noted.)
TA = +25°C
89
87
85
TA = -40°C
83
81
77
75
TA = +125°C
HICLK = GND
1:1:2:2
HALO TGM-H260V8LF
TRANSFORMER
79
0
0.05
0.10
0.15
0.20
0.25
EFFICIENCY (%)
87
HICLK = VDD
85
83
81
1:1:2:2
HALO TGM-H260V8LF
TRANSFORMER
75
0
0.05
0.10
0.15
0.25
0.20
LOAD CURRENT (A)
VDD = 3.3V
MAX258 toc10
VDD = 3.6V
91
89
77
EFFICIENCY vs. LOAD CURRENT
93
HICLK = GND
91
79
LOAD CURRENT (A)
95
93
EFFICIENCY (%)
EFFICIENCY (%)
91
MAX258 toc08
TA = +85°C
93
EFFICIENCY vs. LOAD CURRENT
95
MAX258 toc09
EFFICIENCY vs. LOAD CURRENT
95
SWITCHING WAVEFORMS
MAX258 toc11
89
T1
5V/div
87
0V
85
VDD = 3.0V
83
81
79
77
75
T2
5V/div
0V
HICLK = GND
1:1:2:2
HALO TGM-H260V8LF
TRANSFORMER
0
0.05
0.10
HICLK = GND
0.15
LOAD CURRENT (A)
www.maximintegrated.com
0.20
0.25
RLOAD = 1kΩ
1µs/div
Maxim Integrated │ 5
MAX258
500mA, Push-Pull Transformer Driver
for Isolated Power Supplies
Pin Configuration
TOP VIEW
T1
PGND
T2
GND
8
7
6
5
MAX258
*EP
+
1
VDD
2
3
GND HICLK
4
EN
TDFN
*EXPOSED PAD—CONNECT TO GND
Pin Description
PIN
NAME
1
VDD
Power-Supply Input. Bypass VDD to GND with a 1µF capacitor as close as possible to the device.
2, 5
GND
Logic and Analog Ground
3
HICLK
4
EN
Active-Low Enable Input. Drive EN low to enable the device. Drive EN high to disable the device.
6
T2
Transformer Drive Output 2
7
PGND
8
T1
Transformer Drive Output 1
—
EP
Exposed Pad. Internally connected to GND. Connect EP to a large ground plane to maximize thermal
performance; not intended as an electrical connection point.
www.maximintegrated.com
FUNCTION
Internal Oscillator Frequency Select Input. Drive HICLK high to set the internal oscillator to a 600kHz
switching frequency. Drive HICLK low to set the internal oscillator to a 250kHz switching frequency.
Power Ground. The transformer primary current flows through PGND. Ensure a low-resistance
connection to ground.
Maxim Integrated │ 6
MAX258
500mA, Push-Pull Transformer Driver
for Isolated Power Supplies
Functional Diagram
VDD
T1
UVLO
MAX258
HICLK
DRIVER
T2
FLIPFLOP
OSC
EN
GND
Detailed Description
The MAX258 is an integrated primary-side transformer
driver for isolated power-supply circuits. An on-board
oscillator and internal MOSFETs provide up to 500mA of
drive current to the primary windings of a center-tapped
transformer. The IC features an internal oscillator for
autonomous operation. An internal flip-flop stage guarantees a fixed 50% duty cycle to prevent DC current flow in
the transformer.
The device operates from a single +3.0V to +5.5V supply
and includes undervoltage lockout for controlled startup.
Thermal shutdown circuitry provides additional protection
against excessive power dissipation.
Isolated Power-Supply Application
The IC allows a versatile range of secondary-side rectification circuits (see Figure 2). The primary-to-secondary
transformer winding ratio can be chosen to adjust the
isolated output voltage. The device allows up to 500mA of
current into the primary transformer winding with a supply
voltage up to +5.5V.
www.maximintegrated.com
PGND
Internal Oscillator
The device includes an internal oscillator with a guaranteed 50% duty cycle. Drive the HICLK input high to set
the internal oscillator frequency to 600kHz (typ). Drive the
HICLK input low to set the internal oscillator frequency to
250kHz (typ).
Slew-Rate Control
The T1 and T2 drivers feature a controlled slew rate to
limit EMI.
Disable Mode
The IC includes a pin-selectable disable mode to reduce
current consumption. In disable mode the device consumes less than 5µA (max) of supply current. The T1 and
T2 outputs are high impedance in disable mode.
Power-Up and Undervoltage Lockout
The IC provides an undervoltage lockout feature to
ensure a controlled power-up state and prevent operation
before the oscillator has stabilized. On power-up and during normal operation, if the supply voltage drops below
VUVLO, the undervoltage-lockout circuit forces the device
into disable mode. The T1 and T2 outputs are high impedance in disable mode.
Maxim Integrated │ 7
MAX258
T1
500mA, Push-Pull Transformer Driver
for Isolated Power Supplies
High-Temperature Operation
1CT:nCT
+
-
VIN
VOUT = nVIN - VD
T2
VD = DIODE FORWARD VOLTAGE
(A) PUSH-PULL RECTIFICATION
T1
1CT:nCT
Power-Supply Decoupling
+
VIN
VOUT = 2(nVIN - VD)
-
T2
VD = DIODE FORWARD VOLTAGE
(B) VOLTAGE DOUBLER
T1
When the device is operated under high ambient temperatures, the power dissipated in the package can raise
the junction temperature close to the thermal shutdown
threshold. Under such temperature conditions, the power
dissipation should be held low enough that the junction
temperature observes a factor of safety margin. The
maximum junction temperature should be held below
+140°C. Use the package’s thermal resistance to calculate the junction temperature.
1CT:nCT
Bypass VDD to ground with a 1µF ceramic capacitor as
close as possible to the device.
Connect at least 10µF between VDD and ground as close
as possible to the primary-side center tap of the transformer. This capacitor helps to stabilize the voltage on
the supply line and protects the IC against large voltage
spikes on VDD.
Output Voltage Regulation
VIN
+
VOUT = nVIN - 2VD
T2
VD = DIODE FORWARD VOLTAGE
(C) FULL-WAVE RECTIFIER
Figure 2. Secondary-Side Rectification Topologies
Thermal Shutdown
The device is protected from overtemperature damage
by integrated thermal-shutdown circuitry. When the junction temperature (TJ) exceeds +160ºC (typ), the device is
disabled. The device resumes normal operation when TJ
falls below +130°C (typ).
Applications Information
Power Dissipation
The power dissipation of the device is approximated by:
PD = (RO x IPRI2) + (IDD x VDD)
where RO is the resistance of the internal FET drivers and
IPRI is the load current flowing into T1 and T2. Ensure that
the power dissipation of the MAX258 is kept below the
Absolute Maximum Ratings for proper operation.
www.maximintegrated.com
For many applications, the unregulated output of the circuit meets output voltage tolerances. This configuration
represents the highest efficiency possible. When the load
currents on the transformer’s secondary side are low, the
output voltage of the rectifier can strongly increase. To
protect downstream circuitry, limit the output voltage when
operating the circuit under low load conditions. If the minimum output load current is less than approximately 5mA,
connect a zener diode from the output node of the rectifier
to ground to limit the output voltage to a safe value.
For applications requiring a regulated output voltage,
Maxim provides several solutions. In the following examples, assume a tolerance of ±10% for the input voltage.
Example 1: 5V to Isolated, Unregulated 6V
In the circuit of Figure 3, the MAX258 is used to generate
an isolated 5V output. For a minimum input voltage of 5V,
the output voltage of the rectifier is approximately 6V.
Example 2: 3.3V to Isolated, Regulated 5V
In the circuit of Figure 4, the MAX8881 low-dropout linear regulator regulates the isolated output voltage to 5V.
A 1:2 center-tapped transformer is used to step-up the
secondary-side voltage from a 3.3V input. For a minimum
input voltage of 3.3V, the output voltage of the rectifier is
approximately 6V.
Maxim Integrated │ 8
MAX258
500mA, Push-Pull Transformer Driver
for Isolated Power Supplies
5V
1µF
VDD
T2
HICLK
1CT:1.3CT
1µF
MAX258
6V
ISO OUTPUT
10µF
EN
T1
GND
PGND
Figure 3. 5V to Isolated, Unregulated 6V Application Circuit
3.3V
1µF
VDD
T2
HICLK
1CT:2CT
IN
1µF
MAX258
SHDN
OUT
MAX8881
FB
5V
ISO OUTPUT
4.7µF
10µF
EN
T1
GND
GND
PGND
Figure 4. 3.3V to Isolated, Regulated 5V Application Circuit
PCB Layout Guidelines
ensuring that the current flowing through the primary-side
center tap of the transformer does not flow through the
same trace that connects the supply pin of the MAX258 to
the VDD source, and connect the primary-side center tap
to the VDD supply using a very low inductance connection.
The traces from T1 and T2 to the transformer must be
low-resistance and low-inductance paths. Locate the
transformer as closely as possible to the MAX258 using
short, wide traces.
Exposed Pad
As with all power-supply circuits, careful PCB layout is
important to achieve low switching losses and stable
operation. Connect the exposed pad to a solid copper
ground plane for optimum thermal performance.
If possible, use a power plane for all VDD connections to
the MAX258 and the primary-side of the transformer. If a
power plane is not available, avoid damage to the IC by
www.maximintegrated.com
For optimal thermal performance, ensure that the exposed
pad has a low thermal resistance connection to the
ground plane. Failure to provide a low thermal impedance
path to the ground plane results in excessive junction
temperatures when dissipating high power.
Maxim Integrated │ 9
MAX258
500mA, Push-Pull Transformer Driver
for Isolated Power Supplies
Component Selection
Transformer Selection
Transformer selection for the MAX258 can be simplified
by the use of the ET product. The ET product relates
the maximum allowable magnetic flux density in a transformer core to the voltage across a winding and switching period. Inductor magnetizing current in the primary
winding changes linearly with time during the switching
period of the device. Each transformer has a minimum
ET product, though not always stated on the transformer
data sheet. Ensure that the transformer selected for use
with the device has an ET product of at least ET = VDD/(2
x fSW) for each half of the primary winding, where fSW is
the minimum switching frequency of the T1 and T2 ouputs.
Select a transformer with sufficient ET product for each
half of the primary winding to ensure that the transformer
does not saturate during operation. Saturation of the magnetic core results in significantly reduced inductance of the
primary, and therefore in a large increase in current flow.
For example, when HICLK is low, the required transformer ET product to the center tap for an application with
VDD (max) = 5.5V, is 13.1V-µs. An application with VDD
(max) = 3.3V has a transformer ET product to the center
tap requirement of 7.9V-µs.
In addition to the constraint on ET product, choose a transformer with low leakage inductance and low DC-winding
resistance. Power dissipation of the transformer due to
the copper loss is approximated as:
PD_TX = ILOAD2 x (RPRI /N2 + RSEC)
where RPRI is the DC-winding resistance of the primary,
and RSEC is the DC-winding resistance of the secondary. In most cases, an optimum is reached when RSEC =
RPRI /N2. For this condition, the power dissipation is equal
for the primary and secondary windings.
As with all power-supply designs, it is important to optimize efficiency. In designs incorporating small transformers, the possibility of thermal runaway makes low
transformer efficiencies problematic. Transformer losses
produce a temperature rise that reduces the efficiency of
the transformer. The lower efficiency, in turn, produces an
even larger temperature rise.
To ensure that the transformer meets these requirements
under all operating conditions, the design should focus on
the worst-case conditions. The most stringent demands
on ET product arise for maximum input voltage, minimum
switching frequency, and maximum temperature and load
current. Additionally, the worst-case values for transformer and rectifier losses should be considered.
The primary must be center-tapped; however the secondary winding may or may not be center-tapped, depending
on the rectifier topology used. The phasing between primary and secondary windings is not critical.
The transformer turns ratio must be set to provide the
minimum required output voltage at the maximum anticipated load with the minimum expected input voltage. In
addition, include in the calculations an allowance for the
worst-case losses in the rectifiers. Since the turns ratio
determined in this manner ordinarily produces a much
higher voltage at the secondary under conditions of high
input voltage and/or light loading, take care to prevent an
overvoltage condition from occurring.
Transformers for use with the IC are typically wound on
a high-permeability magnetic core. To minimize radiated
electromagnetic emissions, select a toroid, pot core, E/I/U
core, or equivalent.
Diode Selection
The high switching speed capability of the MAX258
necessitates high-speed rectifiers. Ordinary silicon signal
diodes such as the 1N914 or 1N4148 can be used for lowoutput current levels (less than 50mA), but at high-output
current levels, their reverse recovery times might degrade
efficiency. At higher output currents, select low forwardvoltage Schottky diodes to improve efficiency. Ensure
that the average forward current rating for the rectifier
diodes exceeds the maximum load current of the circuit.
For surface-mount applications, Schottky diodes such as
the B230A, MBRS230, and MBRS320 are recommended.
Suggested External Component Manufacturers
Table 1. Suggested External Component Manufacturers
MANUFACTURER
Halo Electronics
Diodes Inc.
Murata Americas
www.maximintegrated.com
COMPONENT
WEBSITE
Transformers
www.haloelectronics.com
Diodes
Capacitors
www.diodes.com
www.murataamericas.com
Maxim Integrated │ 10
MAX258
500mA, Push-Pull Transformer Driver
for Isolated Power Supplies
Package Information
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
MAX258ATA+
-40°C to +125°C
8 TDFN-EP*
+Denotes a lead(Pb)-free/RoHS-compliant package.
*EP = Exposed pad.
Chip Information
For the latest package outline information and land patterns
(footprints), go to www.maximintegrated.com/packages. Note
that a “+”, “#”, or “-” in the package code indicates RoHS status
only. Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN NO.
8 TDFN-EP
T823+1
21-0174
90-0091
PROCESS: BiCMOS
www.maximintegrated.com
Maxim Integrated │ 11
MAX258
500mA, Push-Pull Transformer Driver
for Isolated Power Supplies
Revision History
REVISION
NUMBER
REVISION
DATE
0
5/13
DESCRIPTION
Initial release
PAGES
CHANGED
—
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits)
shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
© 2013 Maxim Integrated Products, Inc. │ 12
Similar pages