TDK MMZ2012Y202BT000 Chip beads for general signal line Datasheet

E M C
C o m p o n e n t s
February 2015
Chip Beads
For general signal line
MMZ Series
MMZ2012 Type
MMZ2012
2012[0805 inch]*
* Dimensions Code JIS[EIA]
(2/11)
E M C
C o m p o n e n t s
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
20150203 / beads_commercial_signal_mmz2012_en.fm
(3/11)
E M C
C o m p o n e n t s
Chip Beads
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
For general signal line
Overview of MMZ2012 Type
FEATURES
Noise reduction solution for general signal line.
Various frequency characteristics with 8 materials of different features for countermeasures against everything from general signals to
high-speed signals.
APPLICATION
Noise removal for mobile devices such as smartphones and tablet terminals, and various modules.
Noise removal for PCs and recorders, household appliances such as STBs, smart grids, and industrial equipment.
PART NUMBER CONSTRUCTION
MMZ
Series name
2012
L×W×T Dimensions
(mm)
2012
2.0×1.25x0.85
S
Material name
D
R
S
Y
150
A
Impedance
(:) at 100MHz
121
120
150
15
Characteristic
type
A
B
T
000
Packaging style
Internal code
T
Taping
000
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Temperature range
Operating
Storage
Type
temperature
temperature
(°C)
(°C)
MMZ2012
–55 to +125
–55 to +125
The Storage temperature range is for after the circuit board is mounted.
Package quantity
Individual weight
(pieces/reel)
4,000
(mg)
8
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150203 / beads_commercial_signal_mmz2012_en.fm
(4/11)
E M C
C o m p o n e n t s
MMZ2012 Type
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T: Temperature
T4
T3
T2
T3
t3
T1
t1
t2
t: Time
Preheating
Temp.
T1
T2
150°C
180°C
Time
t1
60 to 120s
Soldering
Temp.
Time
T3
t2
230°C
30 to 60s
Peak
Temp.
T4
250 to 260°C
Time
t3
10s
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150203 / beads_commercial_signal_mmz2012_en.fm
(5/11)
E M C
C o m p o n e n t s
MMZ2012 Type
MATERIAL CHARACTERISTICS
R material: For wide frequency applications calling for broad impedance characteristics. For digital signal line applications calling
requiring good waveform integrity. Impedance values selected for effectiveness at 10 to 200MHz.
S material: Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line applications in
which the blocking region is near 100MHz. Impedance values selected for effectiveness at 40 to 300MHz.
Y material: High frequency range type intended for the 100MHz region and above.
For signal line applications in which the signal frequency is far from the cutoff frequency. Impedance values selected for
effectiveness at 80 to 400MHz.
D material: For applications calling for low insertion loss at low frequencies and sharply increasing impedance at high frequencies.
Designed for high impedance at high frequencies (300MHz to 1GHz) for signal line applications.
TYPICAL MATERIAL IMPEDANCE CHARACTERISTICS
2500
Impedance(Ω)
2000
Y
1500
1000
500
0
10
S
D
R
100
Frequency(MHz)
1000
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150203 / beads_commercial_signal_mmz2012_en.fm
(6/11)
E M C
C o m p o n e n t s
MMZ2012 Type
SHAPE & DIMENSIONS
0.85±0.2
1.25±0.2
2±0.2
Dimensions in mm
0.5±0.3
1.2
RECOMMENDED LAND PATTERN
0.8
1
0.8
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150203 / beads_commercial_signal_mmz2012_en.fm
(7/11)
E M C
C o m p o n e n t s
MMZ2012 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Impedance
[100MHz]
(: )
15
30
60
120
300
600
1000
40
80
120
180
300
600
1000
15
30
60
120
300
600
1000
1500
2000
80
120
300
Tolerance
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
±25%
DC resistance
Rated current
Part No.
(: )max.
0.05
0.05
0.10
0.12
0.15
0.20
0.30
0.10
0.10
0.15
0.15
0.20
0.30
0.35
0.05
0.05
0.10
0.12
0.15
0.20
0.30
0.40
0.50
0.30
0.30
0.50
(mA)max.
1500
1500
1000
800
600
500
500
1000
800
800
600
600
500
500
1500
1500
1000
800
600
500
500
500
400
500
500
400
MMZ2012R150AT000
MMZ2012R300AT000
MMZ2012R600AT000
MMZ2012R121AT000
MMZ2012R301AT000
MMZ2012R601AT000
MMZ2012R102AT000
MMZ2012S400AT000
MMZ2012S800AT000
MMZ2012S121AT000
MMZ2012S181AT000
MMZ2012S301AT000
MMZ2012S601AT000
MMZ2012S102AT000
MMZ2012Y150BT000
MMZ2012Y300BT000
MMZ2012Y600BT000
MMZ2012Y121BT000
MMZ2012Y301BT000
MMZ2012Y601BT000
MMZ2012Y102BT000
MMZ2012Y152BT000
MMZ2012Y202BT000
MMZ2012D800BT000
MMZ2012D121BT000
MMZ2012D301BT000
○ Measurement equipment
Measurement item
Product No.
Impedance
E4991A+16192A
DC resistance
Type-7556
* Equivalent measurement equipment may be used.
Manufacturer
Agilent Technologies
Yokogawa
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150203 / beads_commercial_signal_mmz2012_en.fm
(8/11)
E M C
C o m p o n e n t s
MMZ2012 Type
ELECTRICAL CHARACTERISTICS
Z VS. FREQUENCY CHARACTERISTICS (BY SERIES)
MMZ2012R SERIES
MMZ2012S SERIES
MMZ2012R102A
MMZ2012R601A
1000
MMZ2012R301A
MMZ2012R121A
900
MMZ2012R600A
800
MMZ2012R300A
MMZ2012R150A
700
600
500
400
MMZ2012S181A
500
400
200
100
100
10000
2000
600
300
100
1000
Frequency (MHz)
MMZ2012S601A
MMZ2012S301A
700
200
10
MMZ2012Y202B
MMZ2012S121A
800
300
0
1
2500
MMZ2012S102A
1000 MMZ2012S800A
900 MMZ2012S400A
Impedance (Ω)
1100
1100
Impedance (Ω)
1200
Impedance (Ω)
MMZ2012Y SERIES
1200
0
1
MMZ2012Y600B
MMZ2012Y152B
MMZ2012Y300B
MMZ2012Y102B
1500 MMZ2012Y150B
MMZ2012Y601B
MMZ2012Y301B
MMZ2012Y121B
1000
500
10
100
1000
Frequency (MHz)
10000
0
1
10
100
1000
Frequency (MHz)
10000
MMZ2012D SERIES
4500
4000
MMZ2012D301B
Impedance (Ω)
3500
3000
2500
2000
MMZ2012D121B
1500 MMZ2012D800B
1000
500
0
1
10
100
1000
Frequency (MHz)
10000
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150203 / beads_commercial_signal_mmz2012_en.fm
(9/11)
E M C
C o m p o n e n t s
MMZ2012 Type
ELECTRICAL CHARACTERISTICS
Z, X, R VS. FREQUENCY CHARACTERISTICS
MMZ2012R150AT000
MMZ2012R300AT000
R
X
10
100
1000
Frequency (MHz)
10000
140
120
100
80
60
40
20
0
1
Z
R
X
10
100
1000
Frequency (MHz)
10000
350
300
250
200
150
100
50
0
1
1200
60
1000
50
Z
600
R
400
200
0
1
X
10
100
1000
Frequency (MHz)
700
600
500
400
300
200
100
0
1
X
100
1000
Frequency (MHz)
10000
Z
30
R
20
X
10
10
Z
R
100
1000
Frequency (MHz)
10000
X
10
100
1000
Frequency (MHz)
Z
R
50
0
1
10000
140
120
100
80
60
40
20
0
1
X
10
100
1000
Frequency (MHz)
10000
Impedance (Ω)
MMZ2012S102AT000
Z
R
X
10
200
100
100
1000
Frequency (MHz)
10000
450
400
350
300
250
200
150
100
50
0
1
30
1000
25
600
Z
R
400
200
0
1
X
10
10
100
1000
Frequency (MHz)
10000
Z
R
X
10
100
1000
Frequency (MHz)
10000
Z
R
X
10
100
1000
Frequency (MHz)
10000
Z
R
X
10
100
1000
Frequency (MHz)
10000
MMZ2012Y150BT000
1200
800
X
MMZ2012S301AT000
250
150
R
MMZ2012S800AT000
300
Impedance (Ω)
Impedance (Ω)
Impedance (Ω)
R
10
Z
MMZ2012R601AT000
MMZ2012S181AT000
MMZ2012S601AT000
700
600
500
400
300
200
100
0
1
10000
Z
40
0
1
10000
MMZ2012S121AT000
180
160
140
120
100
80
60
40
20
0
1
100
1000
Frequency (MHz)
MMZ2012S400AT000
Impedance (Ω)
Impedance (Ω)
MMZ2012R102AT000
800
10
MMZ2012R301AT000
Impedance (Ω)
Impedance (Ω)
MMZ2012R121AT000
X
Impedance (Ω)
0
1
R
Impedance (Ω)
5
Z
Impedance (Ω)
Z
10
90
80
70
60
50
40
30
20
10
0
1
Impedance (Ω)
15
Impedance (Ω)
Impedance (Ω)
20
Impedance (Ω)
40
0
35
30
25
20
15
10
5
0
1
25
MMZ2012R600AT000
100
1000
Frequency (MHz)
10000
Z
20
R
15
10
X
5
0
1
10
100
1000
Frequency (MHz)
10000
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150203 / beads_commercial_signal_mmz2012_en.fm
(10/11)
E M C
C o m p o n e n t s
MMZ2012 Type
ELECTRICAL CHARACTERISTICS
120
40
100
Z
30
R
20
10
X
100
1000
Frequency (MHz)
Impedance (Ω)
Impedance (Ω)
Z
R
300
200
100
0
1
X
10
100
1000
Frequency (MHz)
10000
Z
R
X
10
100
1000
Frequency (MHz)
10
100
1000
Frequency (MHz)
800
700
600
500
400
300
200
100
0
Z
R
100
50
0
1
10000
X
10
100
1000
Frequency (MHz)
10000
MMZ2012Y102BT000
1200
1000
Z
R
X
1
10
100
1000
Frequency (MHz)
R
400
X
200
10
100
1000
Frequency (MHz)
10000
MMZ2012D800BT000
Z
1500
1000
X
R
10
Z
600
0
1
10000
2000
500
800
100
1000
Frequency (MHz)
10000
700
600
500
400
300
200
100
0
1
Z
10
X
R
100
1000
Frequency (MHz)
10000
MMZ2012D301BT000
Impedance (Ω)
1000
Impedance (Ω)
1
0
1
10000
1200
800
600
400
0
1
X
20
150
2500
MMZ2012D121BT000
200
40
MMZ2012Y202BT000
Impedance (Ω)
Impedance (Ω)
MMZ2012Y152BT000
1800
1600
1400
1200
1000
800
600
400
200
0
1
R
MMZ2012Y601BT000
600
500
400
Z
60
0
10000
MMZ2012Y301BT000
80
Impedance (Ω)
10
200
Impedance (Ω)
0
1
MMZ2012Y121BT000
Impedance (Ω)
50
Impedance (Ω)
Impedance (Ω)
Z, X, R VS. FREQUENCY CHARACTERISTICS
MMZ2012Y300BT000
MMZ2012Y600BT000
Z
X
R
10
100
1000
Frequency (MHz)
10000
4500
4000
3500
3000
2500
2000
1500
1000
500
0
1
Z
R
10
X
100
1000
Frequency (MHz)
10000
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150203 / beads_commercial_signal_mmz2012_en.fm
(11/11)
E M C
C o m p o n e n t s
MMZ2012 Type
PACKAGING STYLE
REEL DIMENSIONS
ø60min.
2.0±0.5
1.0
8.4 +2.0
–0.0
ø13±0.2
ø21±0.8
14.4max.
ø180±2.0
Dimensions in mm
4.0±0.1
B
A
8.0±0.3
2.0±0.05
3.5±0.05
1.5 +0.1
0
1.75±0.1
TAPE DIMENSIONS
P1
K
Dimensions in mm
Type
MMZ2012
160min.
Drawing direction
A
1.5±0.2
Taping
B
2.3±0.2
P1
4.0±0.1
K
1.1max.
200min.
300min.
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150203 / beads_commercial_signal_mmz2012_en.fm
Similar pages